Also, a thought occured to me: I know our IP range (192.168.0.*) is defined in our Cisco router. Could it be I would have to define the second range in the router for this to work?
Probably yes... I think it's easier to do what you want immediately instead of this apparently useless configuration (two nics in the same box connected to the same network).
]]>#
lo="lo 127.0.0.1"
eth0="eth0 192.168.0.22 netmask 255.255.255.0 broadcast 192.168.0.255"
eth1="eth1 192.168.1.23 netmask 255.255.255.0 broadcast 192.168.1.255"
INTERFACES=(lo eth0 eth1)
and in modprobe.conf
#
# /etc/modprobe.conf (for v2.6 kernels)
#
alias eth0 3c59x
alias eth1 8139too
# OSS Compatibility
install snd-pcm modprobe -i snd-pcm ; modprobe snd-pcm-oss ; true
install snd-seq modprobe -i snd-seq ; modprobe snd-seq-oss ; true
____________________________
Can anybody tell if my netmasks are correct in rc.conf?
Also, a thought occured to me: I know our IP range (192.168.0.*) is defined in our Cisco router. Could it be I would have to define the second range in the router for this to work?
Thanks much again.
marco
]]>Use something like e.g. 192.168.0.22 and 192.168.1.22
]]>alias 3c59x eth0
alias 8139too eth1
otherwise it's *possible* that they load up in the wrong order
]]>The machine is an old Dell Gx1 with onboard NIC (3C905B.) I've installed a Network Everywhere card which, according to the documentation, I should treat as an Realtek 8139.
I've assigned IP's to both NIC's, and when I have just the first card hooked up, I can ping either IP or SSH into the machine via either IP. If I put the ethernet cable only to the 2nd NIC, I get nothing. Currently, I have both NIC's cabled up, but how I can I tell if they are working properly?
My ultimate goal is to install the bridge-utils package (I realize that when I do this I won't be assigning the IP's as I have them now.)
http://www.archlinux.org/packages.php?id=4220
Here is the relevant info from rc.conf:
#
lo="lo 127.0.0.1"
eth0="eth0 192.168.0.22 netmask 255.255.255.0 broadcast 192.168.0.255"
eth1="eth1 192.168.0.23 netmask 255.255.255.0 broadcast 192.168.0.255"
INTERFACES=(lo eth0 eth1)
#
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# (prefix a route in ROUTES with a ! to disable it)
#
gateway="default gw 192.168.0.1"
ROUTES=(gateway)
from lspci
00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 02)
00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 02)
00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01)
00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01)
00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
00:0e.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
00:11.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 24)
01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage Pro AGP 1X/2X (rev 5c)
and lsmod
Module Size Used by
8139too 27904 0
mii 5760 1 8139too
3c59x 40232 0
rtc 13128 0
Thanks much
]]>