I have to wonder Jamiroph and n0dl, anyone else: do you have tablet sensitivity issues as noted in this thread? https://bbs.archlinux.org/viewtopic.php?id=134803
I'm unsure if this is relative to only certain types of tablets, but if you do have these problems, please watch (or join?) the discussion.
** EDIT **: It's also worth noting: if your tablet stops working as a result of a kernel upgrade, it's because the kernel upgrade overwrote the wacom.ko. >.>; Since the wacom.ko has been replaced, those steps need to be performed again.
]]>FYI: Please do a pacman -Syu and reboot before you begin this - it's very important. My updated kernel is 3.2.5-1-ARCH.
#1. First check lsusb to see if the Wacom device is being detected:
lsusb | grep Wacom
Bus 002 Device 003: ID 056a:00dd Wacom Co., Ltd
#2. If it is, obtain xf86-input-wacom-git from the AUR (I used yaourt).
yaourt -S xf86-input-wacom-git
#3. Grab the tablet driver from here, third post down as an attachment (wacom-bamboo.tar.gz):
http://sourceforge.net/mailarchive/foru … om-discuss
#4. Decompress this archive in a directory of your choice.
#5. Change to that directory and run
make -C /lib/modules/`uname -r`/build/ SUBDIRS=$(pwd) modules
#6. Run [as root]
depmod -a
#7. Copy the compiled file to the tablet module's directory:
cp wacom.ko /lib/modules/`uname -r`/kernel/drivers/input/tablet/wacom.ko
#8. Create a file called 10-wacom.rule under /etc/udev/rules.d/ and place this within it:
ATTRS{idVendor}=="056a", ATTRS{idProduct}=="00dd", SYMLINK="input/tablet-bamboo-pen"
(This was not automatically generated for me on install of any package.)
#9. Under /lib/modules/`uname -r`/kernel/drivers/input/tablet/, backup the original wacom.ko.gz (I renamed it to wacom.ko.gz.backup), and gzip the wacom.ko
gzip wacom.ko
wacom.ko.gz should be in the directory again.
#10. Add wacom to the MODULES area of /etc/rc.conf.
#11. In /etc/X11/xorg.conf I've placed the following. I'm still troubleshooting things, but for the moment (and I literally mean for the moment) this works:
Section "InputDevice"
Driver "wacom"
Identifier "stylus"
# Option "Device" "/dev/input/wacom-stylus"
Option "Device" "/dev/input/tablet-bamboo-pen"
Option "Type" "stylus"
Option "USB" "on" # USB ONLY
# Changed to Relative: 02-12 @ 1:10pm
Option "Mode" "Relative" # other option: "Absolute" Relative
Option "Vendor" "WACOM"
# Option "tilt" "on" # add this if your tablet supports tilt
# Option "Threshold" "5" # the official linuxwacom howto advises this line
EndSection
Add to Section "ServerLayout":
InputDevice "stylus" "SendCoreEvents"
#12. Reboot.
#13. Start X, and it should operate in one of it's modes (tablet or mouse) when you draw on it. It's worth noting here that while the tablet works in KDE, doing a cat /dev/input/tablet-bamboo-pen did nothing from the prompt when using the tablet.
I'm not sure of the tablet's limitations, but it's working for the moment. I don't mean to redo instructions already provided, but I needed something slightly more straightforward, guys.
It's worth noting the way /dev/input/ currently looks using this method:
by-id event0 event2 event4 event6 event8 js0 mice mouse1 tablet-bamboo-pen
by-path event1 event3 event5 event7 event9 js1 mouse0 mouse2
Just for reference, nothing spectacular.
]]>It also appears in lsmod: -
lsmod | grep wacom
wacom 33718 0
usbcore 146209 7 ehci_hcd,uhci_hcd,usbhid,wacom,uas,usb_storage
I've followed the above article with regards to applying the patched kernel module and added the line for my pen device in the 10-wacom udev file as well but I still don't get any wacom devices listed in /dev/input. Is there anyone else who had this issue and managed to fix it or any further things I could check?
]]>Thank you for sharing this info around.
]]>Everything seemed to load properly, but still no symlink.
In addition to n0dl's excellent instructions (thanks n0dl!) there are two things you need to do to get CTL-470K (Bamboo Connect Pen) working:
Add the following to the '# Type-named links for multiple tablets' section of /etc/udev/rules.d/10-wacom.rule generated by xf86-input-wacom-git:
ATTRS{idVendor}=="056a", ATTRS{idProduct}=="00dd", SYMLINK="input/tablet-bamboo-pen"
And make sure that the wacom.ko you get after the 'make' step supersedes the previous version (back up the old wacom.ko.gz and put the newly-obtained wacom.ko in its place after gzipping it).
Add wacom to the MODULES array in rc.conf and reboot. The tablet should work after this.
]]>First obtain the xf86-input-wacom-git package from the AUR. This will provide the much needed udev rules and X11 configuration options. Next grab the patch from the third post in this thread (it's an attachment), decompress it, then run
make -C /lib/modules/`uname -r`/build/ SUBDIRS=$(pwd) modules
then
depmod -a
and finally copy the kernel module to the tablet drivers directory as such:
cp wacom.ko /lib/modules/`uname -r`/kernel/drivers/input/tablet/wacom.ko
Afterward you should restart. Once you do check to see if theres a wacom symlink in the /dev/input directory, then cat it move your stylus around and see if it works (there should just be a bunch of random characters when you move it around the tablet).
I will probably work on some AUR package in the near future.
]]>lsusb | grep Wacom
Bus 002 Device 003: ID 056a:00dd Wacom Co., Ltd
and I loaded the driver:
sudo modprobe wacom
lsmod | grep wacom
wacom 27924 0
usbcore 120796 6 wacom,uvcvideo,usbhid,uhci_hcd,ehci_hcd
In system settings, under Wacom Graphics Tablet, it says "No tablet detected please plug in or turn on your Wacom tablet." I know this is a new model and is not supported in the kernel, but I can't even get the patches working that others say work fine. I also multi-boot with ubuntu, debian, fedora, and slack. I've tried it on Ubuntu and have the same issue- haven't tried it on the others yet. Any help is greatly appreciated.
]]>