Can anyone explain this? Surely it should have worked fine before making dhcpcd a service?
]]>Would I even get error messages using wpa_supplicant? I thought that's only with netctl. I invoke the settings with wpa_supplicant -B -i wlo1 -c /etc/wpa_supplicant/wpa_supplicant.conf then try to connect with dhcpcd wlo1, and it simply doesn't aqcuire the carrier; it doesn't say anything was logged after it times out.
]]>BSS 00:1a:1e:84:64:65(on wlo1)
TSF: 73799768253 usec (0d, 20:29:59)
freq: 2437
beacon interval: 100 TUs
capability: ESS Privacy ShortPreamble ShortSlotTime (0x0431)
signal: -59.00 dBm
last seen: 520 ms ago
Information elements from Probe Response frame:
SSID: ACStudent
Supported rates: 18.0* 24.0* 36.0 48.0 54.0
DS Parameter set: channel 6
ERP: <no flags>
RSN: * Version: 1
* Group cipher: CCMP
* Pairwise ciphers: CCMP
* Authentication suites: IEEE 802.1X
* Capabilities: 4-PTKSA-RC 4-GTKSA-RC (0x0028)
HT capabilities:
Capabilities: 0x104c
HT20
SM Power Save disabled
RX HT40 SGI
No RX STBC
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT RX MCS rate indexes supported: 0-15
HT TX MCS rate indexes are undefined
HT operation:
* primary channel: 6
* secondary channel offset: no secondary
* STA channel width: 20 MHz
* RIFS: 0
* HT protection: non-HT mixed
* non-GF present: 0
* OBSS non-GF present: 1
* dual beacon: 0
* dual CTS protection: 0
* STBC beacon: 0
* L-SIG TXOP Prot: 0
* PCO active: 0
* PCO phase: 0
WPA: * Version: 1
* Group cipher: CCMP
* Pairwise ciphers: CCMP
* Authentication suites: IEEE 802.1X
* Capabilities: 4-PTKSA-RC 4-GTKSA-RC (0x0028)
WMM: * Parameter version 1
* BE: CW 15-1023, AIFSN 3
* BK: CW 15-1023, AIFSN 7
* VI: CW 7-15, AIFSN 2, TXOP 3008 usec
* VO: CW 3-7, AIFSN 2, TXOP 1504 usec
BSS 00:1a:1e:84:64:64(on wlo1)
These are the settings described for connecting on Android:
SSID - Enter one of ACStudent or AlgSecureWLAN.
Security 802.1x - Select EAP.
EAP Method - Select PEAP.
Phase2 authentication - Select MSCHAPV2.
Identity - Enter your username.
Password - Enter your network account password.
And this is my attempted wpa_supplicant config:
network={
ssid="ACStudent"
key_mgmt=WPA-EAP
eap=PEAP
identity="smit0052"
password="cY402901"
phase2="auth=MSCHAPV2"
}
If anyone could point out if there's a problem with my config or let me know that there's not, I'd really appreciate it.
MOD EDIT: Please use code tags when pasting terminal output. ~fukawi2
]]>