2006-03-13T13:01:30ZFluxBBhttps://bbs.archlinux.org/viewtopic.php?id=19542There is a pkg for the firmware in in [dibble] too ]]>https://bbs.archlinux.org/profile.php?id=18732006-03-13T13:01:30Zhttps://bbs.archlinux.org/viewtopic.php?pid=148843#p148843You need to configure eth1 - loading the firmware is only the first step. Read the network and wireless stuff in the wiki. I don't use profiles myself, so I can't be more specific.]]>https://bbs.archlinux.org/profile.php?id=18222006-03-11T21:43:59Zhttps://bbs.archlinux.org/viewtopic.php?pid=148559#p148559Thanks for help. Firmware loads no problem. eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 eth1: resetting device... eth1: uploading firmware... eth1: firmware version: 1.0.4.3 eth1: firmware upload complete eth1: interface reset complete eth0: no IPv6 routers present eth1: no IPv6 routers present eth1: islpci_close () But iwconfig gives me: eth1 NOT READY! ESSID:off/any Mode:Managed Channel:0 Access Point: 00:00:00:00:00:00 Tx-Power=31 dBm Sensitivity=0/200 Retry min limit:0 RTS thr=0 B Fragment thr=0 B Encryption key:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I think I need some editing in /etc/network/profiles/main or should I go with menu and create seperate file for eth1? Any chances for autodect or you always have to put SSID and KEY? Andrey]]>https://bbs.archlinux.org/profile.php?id=55802006-03-11T18:39:24Zhttps://bbs.archlinux.org/viewtopic.php?pid=148516#p148516It's not Arch-specific. Create /lib/firmware, download version 1.0.4.3 from here, and rename it isl3890.]]>https://bbs.archlinux.org/profile.php?id=18222006-03-11T17:42:28Zhttps://bbs.archlinux.org/viewtopic.php?pid=148503#p148503This is probably a problem /lib/firmware doesn't even exist. Where do I get the firmware from? Does it have to be Arch specific? Andrey Thanks for help]]>https://bbs.archlinux.org/profile.php?id=55802006-03-11T14:42:02Zhttps://bbs.archlinux.org/viewtopic.php?pid=148472#p148472Is the firmware file in the right place - /lib/firmware?]]>https://bbs.archlinux.org/profile.php?id=18222006-03-11T09:30:59Zhttps://bbs.archlinux.org/viewtopic.php?pid=148435#p148435Hello . I have 2 network cards: wired uses via_rhine and mii modules, and smc2802W using prism54 module. Via is eth1 and smc is eth0 I set them up in this order because prism54 tries to load firmware always to eth0 even if I set via card as eth0(any way to change where the firmware is uploaded?) I'm getting error: eth0: resetting device... eth0: uploading firmware... prism54: request_firmware() failed for 'isl3890' eth0: could not upload firmware ('isl3890') eth0: islpci_reset: failure What goes wronge there? I have connection on via card no problems. iwconfig gives me : eth0 NOT READY! ESSID:"default" Mode:Managed Channel:0 Access Point: 00:00:00:00:00:00 Tx-Power=31 dBm Sensitivity=0/200 Retry min limit:0 RTS thr=0 B Fragment thr=0 B Encryption key:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Thanks for help Andrey]]>https://bbs.archlinux.org/profile.php?id=55802006-03-11T06:16:16Zhttps://bbs.archlinux.org/viewtopic.php?pid=148413#p148413