@oeht
You may want to edit the typo in your post, the directory is /etc/modprobe.d/ not /etc/modeprobe.d/.
Thank you for reading it exactly! It's corrected.
]]>You may want to edit the typo in your post, the directory is /etc/modprobe.d/ not /etc/modeprobe.d/.
]]>To sum up for other people, the solution was the following:
1) Install b43-firmware. See this entry in the wiki for how to do this.
2) Create /etc/modprobe.d/local-b43.conf with
# Activate experimental support for some hardware revisions
options b43 allhwsupport=1
Now I'm looking forward to finish my installation and getting a part of the arch community!
]]>I've tried this answer , but it does end in some more errors (dmesg | grep b43):
[ 2.896617] b43-phy0: Broadcom 43224 WLAN found (core revision 23)
[ 2.897153] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 6
[ 2.897163] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2056, Revision 11, Version 0
[ 2.903129] b43 bcma0:1: Direct firmware load for b43/ucode16_mimo.fw failed with error -2
[ 2.903145] b43 bcma0:1: Direct firmware load for b43/ucode16_mimo.fw failed with error -2
[ 2.903164] b43 bcma0:1: Direct firmware load for b43-open/ucode16_mimo.fw failed with error -2
[ 2.903177] b43 bcma0:1: Direct firmware load for b43-open/ucode16_mimo.fw failed with error -2
[ 2.903179] b43-phy0 ERROR: Firmware file "b43/ucode16_mimo.fw" not found
[ 2.903188] b43-phy0 ERROR: Firmware file "b43-open/ucode16_mimo.fw" not found
[ 2.903198] b43-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware for this driver version. Please carefully read all instructions on this website.
so how can I check, if I've installed the firmware the right way or how can I install it now?
]]>[ 3.868434] Support for cores revisions 0x17 and 0x18 disabled by module param allhwsupport=0. Try b43.allhwsupport=1
[ 3.868452] b43: probe of bcma0:1 failed with error -524
[ 3.877968] Broadcom 43xx driver loaded [ Features: PNLS ]
[ 3.912383] brcmsmac bcma0:1: mfg 4bf core 812 rev 23 class 0 irq 22
[ 3.936735] brcmsmac bcma0:1 wlp1s0b1: renamed from wlan0
So, what do you think happens and what other options do you have?
]]>I posted the originally dmesg in the originally post. I found out, that
(...) Wrong diagnostic page: asked for 1 got 8
(...) Failed to get diagnostic page 0xffffffea
(...) Failed to bind enclosure -19
is problem caused by a detective external HD, which I can solve sperately.
Yes, the wifi worked before, so I uninstalled broadcom-wl-dkms and it works again.
Furthermore I created /etc/modprobe.d/blacklist.conf with the content
blacklist wl
but the error still occurs in dmesg.
Here is the output of 'lspci -vnn | grep -i net'
01:00.0 Network controller [0280]: Broadcom Limited BCM43224 802.11a/b/g/n [14e4:4353] (rev 01)
So to mend my suggestion:
"blacklist wl and unblacklist b43 and brcmsmac" (move away the blacklist config provided by wl - or just uninstall broadcom-wl-dkms)
In case, just blacklist the wl module to return to the b43 or brcmsmac module (which ever was actually used)
broadcom-wl-dkms blacklists b43 and brcmsmac see broadcom-wl-dkms.conf would not adding wl to the blacklist just make no drivers available?
]]>I'm not familiar with those messages, but there is a history of broadcom drivers being fairly verbose and emitting harmless warnings.
All in all, if b43 ain't broke, don't try to fix it with wl.
EDIT: the "solution" you linked to was for someone with hardware that was not supported by b43 or - presumably - any other better option, so wl was all that was left. It sounds like your hardware is supported by b43. If in doubt, please post the output of `lspci -vnn | grep -i net`
]]>The output of dmesg (from arch, not ubuntu!) would be a good start for further inspection of the situation.
]]>I'm new to archlinux and I really like the KISS-concept!
I've done the installation part 1 of the german arch wiki. I think this is about the full installation of https://wiki.archlinux.org/index.php/Installation_guide on my macbook air mid 2011 dualboot with ubuntu.
Now, I'm facing the following error after booting:
(...)Support for cores revisions 0x17 and 0x18 disabled by module param allhwsupport=0. Try b43.allhwsupport=1
I've already found this answer, but after
pacman -S broadcom-wl-dkms
I'm no more able to connect to wifi with
wifi-menu
Before the installation of broadcom-wl-dkm, I was able to connect.
EDIT: Here is the output of dmesg:
[ 0.000000] random: get_random_bytes called from start_kernel+0x42/0x4b7 with crng_init=0
[ 0.000000] Linux version 4.13.11-1-ARCH (builduser@tobias) (gcc version 7.2.0 (GCC)) #1 SMP PREEMPT Thu Nov 2 10:25:56 CET 2017
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-linux root=/dev/sda5
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[ 0.000000] x86/fpu: Enabled xstate features 0x3, context size is 576 bytes, using 'standard' format.
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000008efff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000008f000-0x000000000008ffff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x0000000000090000-0x000000000009ffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000006effffff] usable
[ 0.000000] BIOS-e820: [mem 0x000000006f000000-0x000000007effffff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007f000000-0x000000007f718fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007f719000-0x000000007f938fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000007f939000-0x000000007f953fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007f954000-0x000000007f96afff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x000000007f96b000-0x000000007f96efff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007f96f000-0x000000007f99afff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007f99b000-0x000000007f9affff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007f9b0000-0x000000007f9dafff] type 20
[ 0.000000] BIOS-e820: [mem 0x000000007f9db000-0x000000007fef8fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007fef9000-0x000000007fefffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000093200000-0x0000000093200fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ffc00000-0x00000000ffffffff] reserved
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] efi: EFI v1.10 by Apple
[ 0.000000] efi: ACPI=0x7f96a000 ACPI 2.0=0x7f96a014 SMBIOS=0x7f71a000
[ 0.000000] random: fast init done
[ 0.000000] SMBIOS 2.4 present.
[ 0.000000] DMI: Apple Inc. MacBookAir3,2/Mac-942C5DF58193131B, BIOS MBA31.88Z.0061.B07.1201241641 01/24/12
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0x7fef9 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: write-back
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-FFFFF uncachable
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 080000000 mask F80000000 uncachable
[ 0.000000] 1 base 07FF00000 mask FFFF00000 uncachable
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WC UC- WT
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] Base memory trampoline at [ffff991800099000] 99000 size 24576
[ 0.000000] BRK [0x6bd64000, 0x6bd64fff] PGTABLE
[ 0.000000] BRK [0x6bd65000, 0x6bd65fff] PGTABLE
[ 0.000000] BRK [0x6bd66000, 0x6bd66fff] PGTABLE
[ 0.000000] BRK [0x6bd67000, 0x6bd67fff] PGTABLE
[ 0.000000] BRK [0x6bd68000, 0x6bd68fff] PGTABLE
[ 0.000000] BRK [0x6bd69000, 0x6bd69fff] PGTABLE
[ 0.000000] BRK [0x6bd6a000, 0x6bd6afff] PGTABLE
[ 0.000000] BRK [0x6bd6b000, 0x6bd6bfff] PGTABLE
[ 0.000000] Secure boot could not be determined
[ 0.000000] RAMDISK: [mem 0x37332000-0x37990fff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x000000007F96A014 000024 (v02 APPLE )
[ 0.000000] ACPI: XSDT 0x000000007F96A1C0 000084 (v01 APPLE Apple00 00000061 01000013)
[ 0.000000] ACPI: FACP 0x000000007F968000 0000F4 (v04 APPLE Apple00 00000061 Loki 0000005F)
[ 0.000000] ACPI: DSDT 0x000000007F95B000 00572C (v01 APPLE MacBookA 00030001 INTL 20061109)
[ 0.000000] ACPI: FACS 0x000000007F71E000 000040
[ 0.000000] ACPI: FACS 0x000000007F71E000 000040
[ 0.000000] ACPI: HPET 0x000000007F967000 000038 (v01 APPLE Apple00 00000001 Loki 0000005F)
[ 0.000000] ACPI: APIC 0x000000007F966000 000068 (v01 APPLE Apple00 00000001 Loki 0000005F)
[ 0.000000] ACPI: APIC 0x000000007F965000 000068 (v02 APPLE Apple00 00000001 Loki 0000005F)
[ 0.000000] ACPI: ASF! 0x000000007F963000 0000A5 (v32 APPLE Apple00 00000001 Loki 0000005F)
[ 0.000000] ACPI: SBST 0x000000007F962000 000030 (v01 APPLE Apple00 00000001 Loki 0000005F)
[ 0.000000] ACPI: ECDT 0x000000007F961000 000053 (v01 APPLE Apple00 00000001 Loki 0000005F)
[ 0.000000] ACPI: SSDT 0x000000007F958000 000107 (v01 APPLE SataAhci 00001000 INTL 20061109)
[ 0.000000] ACPI: SSDT 0x000000007F957000 000024 (v01 APPLE Apple 00001000 INTL 20061109)
[ 0.000000] ACPI: SSDT 0x000000007F956000 0000FC (v01 APPLE SDCard 00001000 INTL 20061109)
[ 0.000000] ACPI: SSDT 0x000000007F954000 0004DC (v01 APPLE CpuPm 00003000 INTL 20061109)
[ 0.000000] ACPI: MCFG 0x000000007F964000 00003C (v01 APPLE Apple00 00000001 Loki 0000005F)
[ 0.000000] ACPI: BIOS bug: multiple APIC/MADT found, using 0
[ 0.000000] ACPI: If "acpi_apic_instance=2" works better, notify linux-acpi@vger.kernel.org
[ 0.000000] ACPI: DMI detected to setup _OSI("Darwin"): Apple hardware
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000007fef8fff]
[ 0.000000] NODE_DATA(0) allocated [mem 0x7fef4000-0x7fef8fff]
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x000000007fef8fff]
[ 0.000000] Normal empty
[ 0.000000] Device empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000008efff]
[ 0.000000] node 0: [mem 0x0000000000090000-0x000000000009ffff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x000000006effffff]
[ 0.000000] node 0: [mem 0x000000007f000000-0x000000007f718fff]
[ 0.000000] node 0: [mem 0x000000007f939000-0x000000007f953fff]
[ 0.000000] node 0: [mem 0x000000007f96b000-0x000000007f96efff]
[ 0.000000] node 0: [mem 0x000000007f99b000-0x000000007f9affff]
[ 0.000000] node 0: [mem 0x000000007f9db000-0x000000007fef8fff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000007fef8fff]
[ 0.000000] On node 0 totalpages: 457737
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 23 pages reserved
[ 0.000000] DMA zone: 3998 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7090 pages used for memmap
[ 0.000000] DMA32 zone: 453739 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000
[ 0.000000] smpboot: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0008f000-0x0008ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x6f000000-0x7effffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7f719000-0x7f938fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7f954000-0x7f96afff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7f96f000-0x7f99afff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7f9b0000-0x7f9dafff]
[ 0.000000] e820: [mem 0x93201000-0xffbfffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370452778343963 ns
[ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] percpu: Embedded 36 pages/cpu @ffff99186c600000 s106520 r8192 d32744 u1048576
[ 0.000000] pcpu-alloc: s106520 r8192 d32744 u1048576 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 450560
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=/dev/sda5
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 1732260K/1830948K available (6644K kernel code, 1134K rwdata, 2048K rodata, 1336K init, 908K bss, 98688K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] ftrace: allocating 28354 entries in 111 pages
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=2.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 8448, nr_irqs: 440, preallocated irqs: 16
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.003333] tsc: Detected 1858.401 MHz processor
[ 0.003333] Calibrating delay loop (skipped), value calculated using timer frequency.. 3718.66 BogoMIPS (lpj=6194670)
[ 0.003333] pid_max: default: 32768 minimum: 301
[ 0.003333] ACPI: Core revision 20170531
[ 0.009378] ACPI: 5 ACPI AML tables successfully acquired and loaded
[ 0.047949] Security Framework initialized
[ 0.047950] Yama: becoming mindful.
[ 0.048772] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.049173] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.049195] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.049208] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.049480] CPU: Physical Processor ID: 0
[ 0.049481] CPU: Processor Core ID: 0
[ 0.049483] mce: CPU supports 6 MCE banks
[ 0.049490] CPU0: Thermal monitoring enabled (TM2)
[ 0.049493] process: using mwait in idle threads
[ 0.049497] Last level iTLB entries: 4KB 128, 2MB 4, 4MB 4
[ 0.049499] Last level dTLB entries: 4KB 256, 2MB 0, 4MB 32, 1GB 0
[ 0.049629] Freeing SMP alternatives memory: 24K
[ 0.052791] smpboot: Max logical packages: 1
[ 0.053254] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.086666] smpboot: CPU0: Intel(R) Core(TM)2 Duo CPU L9400 @ 1.86GHz (family: 0x6, model: 0x17, stepping: 0xa)
[ 0.096676] Performance Events: PEBS fmt0+, Core2 events, Intel PMU driver.
[ 0.096686] ... version: 2
[ 0.096687] ... bit width: 40
[ 0.096688] ... generic registers: 2
[ 0.096689] ... value mask: 000000ffffffffff
[ 0.096690] ... max period: 000000007fffffff
[ 0.096691] ... fixed-purpose events: 3
[ 0.096692] ... event mask: 0000000700000003
[ 0.103337] Hierarchical SRCU implementation.
[ 0.116756] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.123337] smp: Bringing up secondary CPUs ...
[ 0.150018] x86: Booting SMP configuration:
[ 0.150020] .... node #0, CPUs: #1
[ 0.235364] smp: Brought up 1 node, 2 CPUs
[ 0.235364] smpboot: Total of 2 processors activated (7436.10 BogoMIPS)
[ 0.236871] devtmpfs: initialized
[ 0.236871] x86/mm: Memory block size: 128MB
[ 0.240005] PM: Registering ACPI NVS region [mem 0x0008f000-0x0008ffff] (4096 bytes)
[ 0.240005] PM: Registering ACPI NVS region [mem 0x7f719000-0x7f938fff] (2228224 bytes)
[ 0.240005] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[ 0.240005] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.240005] pinctrl core: initialized pinctrl subsystem
[ 0.240005] RTC time: 7:37:04, date: 11/05/17
[ 0.240005] NET: Registered protocol family 16
[ 0.240015] cpuidle: using governor ladder
[ 0.243339] cpuidle: using governor menu
[ 0.243339] PCCT header not found.
[ 0.243362] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.243363] ACPI: bus type PCI registered
[ 0.243365] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.243666] PCI: MMCONFIG for domain 0000 [bus 00-02] at [mem 0xf0000000-0xf02fffff] (base 0xf0000000)
[ 0.243673] PCI: not using MMCONFIG
[ 0.243673] PCI: Using configuration type 1 for base access
[ 0.244390] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.244390] ACPI: Disabled all _OSI OS vendors
[ 0.244390] ACPI: Added _OSI(Module Device)
[ 0.244390] ACPI: Added _OSI(Processor Device)
[ 0.244390] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.244390] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.244390] ACPI: Added _OSI(Darwin)
[ 0.244390] ACPI: EC: EC started
[ 0.244390] ACPI: EC: interrupt blocked
[ 0.247788] ACPI: \: Used as first EC
[ 0.247790] ACPI: \: GPE=0x57, EC_CMD/EC_SC=0x66, EC_DATA=0x62
[ 0.247792] ACPI: \: Used as boot ECDT EC to handle transactions
[ 0.249927] ACPI: BIOS _OSI(Darwin) query honored via DMI
[ 0.251604] ACPI: Dynamic OEM Table Load:
[ 0.251614] ACPI: SSDT 0xFFFF991868A5F200 0001FB (v01 APPLE Cpu0Ist 00003000 INTL 20061109)
[ 0.251841] ACPI: Dynamic OEM Table Load:
[ 0.251850] ACPI: SSDT 0xFFFF991868A3A800 0005A6 (v01 APPLE Cpu0Cst 00003001 INTL 20061109)
[ 0.252293] ACPI: Dynamic OEM Table Load:
[ 0.252301] ACPI: SSDT 0xFFFF991868A0F900 0000C8 (v01 APPLE Cpu1Ist 00003000 INTL 20061109)
[ 0.252460] ACPI: Dynamic OEM Table Load:
[ 0.252467] ACPI: SSDT 0xFFFF9918689ECCC0 000085 (v01 APPLE Cpu1Cst 00003000 INTL 20061109)
[ 0.252774] ACPI: Interpreter enabled
[ 0.252796] ACPI: (supports S0 S3 S4 S5)
[ 0.252798] ACPI: Using IOAPIC for interrupt routing
[ 0.252825] PCI: MMCONFIG for domain 0000 [bus 00-02] at [mem 0xf0000000-0xf02fffff] (base 0xf0000000)
[ 0.253153] PCI: MMCONFIG at [mem 0xf0000000-0xf02fffff] reserved in ACPI motherboard resources
[ 0.253164] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.265168] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.265174] acpi PNP0A08:00: _OSC: OS assumes control of [PCIeHotplug SHPCHotplug AER PCIeCapability]
[ 0.265185] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-02] only partially covers this bridge
[ 0.265468] PCI host bridge to bus 0000:00
[ 0.265471] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window]
[ 0.265473] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.265475] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[ 0.265477] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000c3fff window]
[ 0.265479] pci_bus 0000:00: root bus resource [mem 0x000c4000-0x000c7fff window]
[ 0.265480] pci_bus 0000:00: root bus resource [mem 0x000c8000-0x000cbfff window]
[ 0.265482] pci_bus 0000:00: root bus resource [mem 0x000cc000-0x000cffff window]
[ 0.265484] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff window]
[ 0.265486] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff window]
[ 0.265488] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff window]
[ 0.265489] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff window]
[ 0.265491] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000e3fff window]
[ 0.265493] pci_bus 0000:00: root bus resource [mem 0x000e4000-0x000e7fff window]
[ 0.265495] pci_bus 0000:00: root bus resource [mem 0x000e8000-0x000ebfff window]
[ 0.265497] pci_bus 0000:00: root bus resource [mem 0x000ec000-0x000effff window]
[ 0.265499] pci_bus 0000:00: root bus resource [mem 0x000f0000-0x000fffff window]
[ 0.265501] pci_bus 0000:00: root bus resource [mem 0x80000000-0xfebfffff window]
[ 0.265503] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.265521] pci 0000:00:00.0: [10de:0d60] type 00 class 0x060000
[ 0.265742] pci 0000:00:00.1: [10de:0d68] type 00 class 0x050000
[ 0.265976] pci 0000:00:01.0: [10de:0d6d] type 00 class 0x050000
[ 0.266198] pci 0000:00:01.1: [10de:0d6e] type 00 class 0x050000
[ 0.266423] pci 0000:00:01.2: [10de:0d6f] type 00 class 0x050000
[ 0.266644] pci 0000:00:01.3: [10de:0d70] type 00 class 0x050000
[ 0.266872] pci 0000:00:02.0: [10de:0d71] type 00 class 0x050000
[ 0.267092] pci 0000:00:02.1: [10de:0d72] type 00 class 0x050000
[ 0.267311] pci 0000:00:03.0: [10de:0d80] type 00 class 0x060100
[ 0.267324] pci 0000:00:03.0: reg 0x10: [io 0x2100-0x21ff]
[ 0.267455] pci 0000:00:03.1: [10de:0d7b] type 00 class 0x050000
[ 0.267610] pci 0000:00:03.2: [10de:0d79] type 00 class 0x0c0500
[ 0.267626] pci 0000:00:03.2: reg 0x10: [io 0x2000-0x20ff]
[ 0.267633] pci 0000:00:03.2: reg 0x14: [mem 0x93286000-0x93287fff]
[ 0.267650] pci 0000:00:03.2: reg 0x20: [io 0x2240-0x227f]
[ 0.267657] pci 0000:00:03.2: reg 0x24: [io 0x2200-0x223f]
[ 0.267694] pci 0000:00:03.2: PME# supported from D3hot D3cold
[ 0.267806] pci 0000:00:03.3: [10de:0d69] type 00 class 0x050000
[ 0.268061] pci 0000:00:03.4: [10de:0d7a] type 00 class 0x0b4000
[ 0.268093] pci 0000:00:03.4: reg 0x10: [mem 0x93200000-0x9327ffff]
[ 0.268320] pci 0000:00:04.0: [10de:0d9c] type 00 class 0x0c0310
[ 0.268335] pci 0000:00:04.0: reg 0x10: [mem 0x9328a000-0x9328afff]
[ 0.268389] pci 0000:00:04.0: supports D1 D2
[ 0.268391] pci 0000:00:04.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.268538] pci 0000:00:04.1: [10de:0d9d] type 00 class 0x0c0320
[ 0.268555] pci 0000:00:04.1: reg 0x10: [mem 0x9328b100-0x9328b1ff]
[ 0.268615] pci 0000:00:04.1: supports D1 D2
[ 0.268616] pci 0000:00:04.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.268787] pci 0000:00:06.0: [10de:0d9c] type 00 class 0x0c0310
[ 0.268802] pci 0000:00:06.0: reg 0x10: [mem 0x93289000-0x93289fff]
[ 0.268856] pci 0000:00:06.0: supports D1 D2
[ 0.268858] pci 0000:00:06.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.269001] pci 0000:00:06.1: [10de:0d9d] type 00 class 0x0c0320
[ 0.269018] pci 0000:00:06.1: reg 0x10: [mem 0x9328b000-0x9328b0ff]
[ 0.269078] pci 0000:00:06.1: supports D1 D2
[ 0.269079] pci 0000:00:06.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.269245] pci 0000:00:08.0: [10de:0d94] type 00 class 0x040300
[ 0.269260] pci 0000:00:08.0: reg 0x10: [mem 0x93280000-0x93283fff]
[ 0.269313] pci 0000:00:08.0: PME# supported from D3hot D3cold
[ 0.269433] pci 0000:00:0a.0: [10de:0d88] type 00 class 0x010601
[ 0.269447] pci 0000:00:0a.0: reg 0x10: [io 0x2298-0x229f]
[ 0.269453] pci 0000:00:0a.0: reg 0x14: [io 0x22a4-0x22a7]
[ 0.269459] pci 0000:00:0a.0: reg 0x18: [io 0x2290-0x2297]
[ 0.269465] pci 0000:00:0a.0: reg 0x1c: [io 0x22a0-0x22a3]
[ 0.269471] pci 0000:00:0a.0: reg 0x20: [io 0x2280-0x228f]
[ 0.269477] pci 0000:00:0a.0: reg 0x24: [mem 0x93284000-0x93285fff]
[ 0.269645] pci 0000:00:0b.0: [10de:0d75] type 00 class 0x050000
[ 0.269659] pci 0000:00:0b.0: reg 0x10: [mem 0x93288000-0x93288fff]
[ 0.269839] pci 0000:00:15.0: [10de:0d9b] type 01 class 0x060400
[ 0.270127] pci 0000:00:15.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.270272] pci 0000:00:17.0: [10de:0d76] type 01 class 0x060400
[ 0.270318] pci 0000:00:17.0: PME# supported from D0 D3hot D3cold
[ 0.270585] pci 0000:01:00.0: [14e4:4353] type 00 class 0x028000
[ 0.270617] pci 0000:01:00.0: reg 0x10: [mem 0x93100000-0x93103fff 64bit]
[ 0.270740] pci 0000:01:00.0: supports D1 D2
[ 0.270742] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.270922] pci 0000:00:15.0: PCI bridge to [bus 01]
[ 0.270944] pci 0000:00:15.0: bridge window [mem 0x93100000-0x931fffff]
[ 0.271016] pci 0000:02:00.0: [10de:08a3] type 00 class 0x030000
[ 0.271029] pci 0000:02:00.0: reg 0x10: [mem 0x92000000-0x92ffffff]
[ 0.271038] pci 0000:02:00.0: reg 0x14: [mem 0x80000000-0x8fffffff 64bit pref]
[ 0.271046] pci 0000:02:00.0: reg 0x1c: [mem 0x90000000-0x91ffffff 64bit pref]
[ 0.271053] pci 0000:02:00.0: reg 0x24: [io 0x1000-0x107f]
[ 0.271059] pci 0000:02:00.0: reg 0x30: [mem 0x93000000-0x9301ffff pref]
[ 0.271256] pci 0000:00:17.0: PCI bridge to [bus 02]
[ 0.271260] pci 0000:00:17.0: bridge window [io 0x1000-0x1fff]
[ 0.271264] pci 0000:00:17.0: bridge window [mem 0x92000000-0x930fffff]
[ 0.271268] pci 0000:00:17.0: bridge window [mem 0x80000000-0x91ffffff 64bit pref]
[ 0.271711] ACPI: PCI Interrupt Link [LNK1] (IRQs *16 17 18 19 20 21 22 23)
[ 0.271831] ACPI: PCI Interrupt Link [LNK2] (IRQs 16 *17 18 19 20 21 22 23)
[ 0.271949] ACPI: PCI Interrupt Link [LNK3] (IRQs 16 17 *18 19 20 21 22 23)
[ 0.272067] ACPI: PCI Interrupt Link [LNK4] (IRQs 16 17 18 *19 20 21 22 23)
[ 0.272186] ACPI: PCI Interrupt Link [Z00J] (IRQs 16 17 18 19 20 *21 22 23)
[ 0.272305] ACPI: PCI Interrupt Link [Z00K] (IRQs 16 17 18 19 20 *21 22 23)
[ 0.272426] ACPI: PCI Interrupt Link [Z00L] (IRQs 16 17 18 19 20 *21 22 23)
[ 0.272544] ACPI: PCI Interrupt Link [Z00M] (IRQs 16 17 18 19 20 *21 22 23)
[ 0.272661] ACPI: PCI Interrupt Link [LSMB] (IRQs 16 17 18 19 20 21 *22 23)
[ 0.272778] ACPI: PCI Interrupt Link [LUS0] (IRQs 16 *17 18 19 20 21 22 23)
[ 0.272894] ACPI: PCI Interrupt Link [LUS2] (IRQs 16 *17 18 19 20 21 22 23)
[ 0.273013] ACPI: PCI Interrupt Link [LMAC] (IRQs 16 *17 18 19 20 21 22 23)
[ 0.273135] ACPI: PCI Interrupt Link [LAZA] (IRQs 16 17 18 19 *20 21 22 23)
[ 0.273252] ACPI: PCI Interrupt Link [LGPU] (IRQs *16 17 18 19 20 21 22 23)
[ 0.273376] ACPI: PCI Interrupt Link [LPID] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 0.273496] ACPI: PCI Interrupt Link [LSI0] (IRQs 16 17 *18 19 20 21 22 23)
[ 0.273614] ACPI: PCI Interrupt Link [Z000] (IRQs 16 17 *18 19 20 21 22 23)
[ 0.273731] ACPI: PCI Interrupt Link [Z001] (IRQs 16 17 18 19 20 21 *22 23)
[ 0.273845] ACPI: PCI Interrupt Link [LPMU] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 0.274049] ACPI: Enabled 3 GPEs in block 00 to 1F
[ 0.274063] ACPI: Enabled 2 GPEs in block 20 to 5F
[ 0.274112] ACPI: EC: EC stopped
[ 0.274113] ACPI: EC: EC started
[ 0.274114] ACPI: EC: interrupt blocked
[ 0.291243] ACPI: EC: interrupt unblocked
[ 0.291253] ACPI: EC: event unblocked
[ 0.291262] ACPI: \_SB_.PCI0.LPCB.EC__: GPE=0x57, EC_CMD/EC_SC=0x66, EC_DATA=0x62
[ 0.291264] ACPI: \_SB_.PCI0.LPCB.EC__: Used as boot ECDT EC to handle transactions and events
[ 0.291292] ACPI: \_SB_.PCI0.LPCB.EC__: GPE=0x57, EC_CMD/EC_SC=0x66, EC_DATA=0x62
[ 0.291294] ACPI: \_SB_.PCI0.LPCB.EC__: Used as boot DSDT EC to handle transactions and events
[ 0.291384] pci 0000:02:00.0: vgaarb: VGA device added: decodes=io+mem,owns=none,locks=none
[ 0.291384] pci 0000:02:00.0: vgaarb: setting as boot device
[ 0.291384] pci 0000:02:00.0: vgaarb: bridge control possible
[ 0.291384] vgaarb: loaded
[ 0.291384] EDAC MC: Ver: 3.0.0
[ 0.291384] Registered efivars operations
[ 0.771721] PCI: Using ACPI for IRQ routing
[ 0.771724] PCI: pci_cache_line_size set to 64 bytes
[ 0.771861] e820: reserve RAM buffer [mem 0x0008f000-0x0008ffff]
[ 0.771862] e820: reserve RAM buffer [mem 0x6f000000-0x6fffffff]
[ 0.771864] e820: reserve RAM buffer [mem 0x7f719000-0x7fffffff]
[ 0.771866] e820: reserve RAM buffer [mem 0x7f954000-0x7fffffff]
[ 0.771868] e820: reserve RAM buffer [mem 0x7f96f000-0x7fffffff]
[ 0.771869] e820: reserve RAM buffer [mem 0x7f9b0000-0x7fffffff]
[ 0.771871] e820: reserve RAM buffer [mem 0x7fef9000-0x7fffffff]
[ 0.771993] NetLabel: Initializing
[ 0.771994] NetLabel: domain hash size = 128
[ 0.771995] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 0.772018] NetLabel: unlabeled traffic allowed by default
[ 0.772069] HPET: 4 timers in total, 0 timers will be used for per-cpu timer
[ 0.772075] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31, 31
[ 0.772081] hpet0: 4 comparators, 64-bit 25.000000 MHz counter
[ 0.776687] clocksource: Switched to clocksource hpet
[ 0.793093] VFS: Disk quotas dquot_6.6.0
[ 0.793121] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.793239] pnp: PnP ACPI init
[ 0.793417] system 00:00: [mem 0xf0000000-0xf3ffffff] has been reserved
[ 0.793422] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.793594] system 00:01: [mem 0xfed00000-0xfed003ff] has been reserved
[ 0.793599] system 00:01: Plug and Play ACPI device, IDs PNP0103 PNP0c01 (active)
[ 0.793746] system 00:02: [io 0x0400-0x047f] has been reserved
[ 0.793748] system 00:02: [io 0x0480-0x04ff] has been reserved
[ 0.793751] system 00:02: [io 0x0500-0x057f] has been reserved
[ 0.793753] system 00:02: [io 0x0580-0x05ff] has been reserved
[ 0.793755] system 00:02: [io 0x0800-0x087f] has been reserved
[ 0.793757] system 00:02: [io 0x0880-0x08ff] has been reserved
[ 0.793760] system 00:02: [io 0x04d0-0x04d1] has been reserved
[ 0.793762] system 00:02: [io 0x0295-0x0296] has been reserved
[ 0.793766] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.793802] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.794249] pnp: PnP ACPI: found 4 devices
[ 0.801554] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[ 0.801595] pci 0000:00:15.0: PCI bridge to [bus 01]
[ 0.801608] pci 0000:00:15.0: bridge window [mem 0x93100000-0x931fffff]
[ 0.801629] pci 0000:00:17.0: PCI bridge to [bus 02]
[ 0.801631] pci 0000:00:17.0: bridge window [io 0x1000-0x1fff]
[ 0.801635] pci 0000:00:17.0: bridge window [mem 0x92000000-0x930fffff]
[ 0.801638] pci 0000:00:17.0: bridge window [mem 0x80000000-0x91ffffff 64bit pref]
[ 0.801643] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window]
[ 0.801646] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window]
[ 0.801648] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[ 0.801649] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000c3fff window]
[ 0.801651] pci_bus 0000:00: resource 8 [mem 0x000c4000-0x000c7fff window]
[ 0.801653] pci_bus 0000:00: resource 9 [mem 0x000c8000-0x000cbfff window]
[ 0.801655] pci_bus 0000:00: resource 10 [mem 0x000cc000-0x000cffff window]
[ 0.801657] pci_bus 0000:00: resource 11 [mem 0x000d0000-0x000d3fff window]
[ 0.801659] pci_bus 0000:00: resource 12 [mem 0x000d4000-0x000d7fff window]
[ 0.801661] pci_bus 0000:00: resource 13 [mem 0x000d8000-0x000dbfff window]
[ 0.801663] pci_bus 0000:00: resource 14 [mem 0x000dc000-0x000dffff window]
[ 0.801665] pci_bus 0000:00: resource 15 [mem 0x000e0000-0x000e3fff window]
[ 0.801667] pci_bus 0000:00: resource 16 [mem 0x000e4000-0x000e7fff window]
[ 0.801669] pci_bus 0000:00: resource 17 [mem 0x000e8000-0x000ebfff window]
[ 0.801671] pci_bus 0000:00: resource 18 [mem 0x000ec000-0x000effff window]
[ 0.801673] pci_bus 0000:00: resource 19 [mem 0x000f0000-0x000fffff window]
[ 0.801674] pci_bus 0000:00: resource 20 [mem 0x80000000-0xfebfffff window]
[ 0.801677] pci_bus 0000:01: resource 1 [mem 0x93100000-0x931fffff]
[ 0.801679] pci_bus 0000:02: resource 0 [io 0x1000-0x1fff]
[ 0.801681] pci_bus 0000:02: resource 1 [mem 0x92000000-0x930fffff]
[ 0.801683] pci_bus 0000:02: resource 2 [mem 0x80000000-0x91ffffff 64bit pref]
[ 0.801797] NET: Registered protocol family 2
[ 0.802017] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.802086] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[ 0.802194] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.802256] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.802274] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.802333] NET: Registered protocol family 1
[ 0.802721] ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 23
[ 0.857062] ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 23
[ 0.857452] ACPI: PCI Interrupt Link [Z000] enabled at IRQ 20
[ 0.913720] ACPI: PCI Interrupt Link [Z001] enabled at IRQ 19
[ 0.913945] PCI: CLS 256 bytes, default 64
[ 0.913994] Unpacking initramfs...
[ 1.059907] Freeing initrd memory: 6524K
[ 1.060140] Scanning for low memory corruption every 60 seconds
[ 1.060908] Initialise system trusted keyrings
[ 1.060921] Key type blacklist registered
[ 1.061008] workingset: timestamp_bits=40 max_order=19 bucket_order=0
[ 1.062967] zbud: loaded
[ 1.064812] Key type asymmetric registered
[ 1.064857] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 1.064898] io scheduler noop registered
[ 1.064900] io scheduler deadline registered
[ 1.064941] io scheduler cfq registered (default)
[ 1.064942] io scheduler mq-deadline registered
[ 1.064943] io scheduler kyber registered
[ 1.064982] io scheduler bfq registered
[ 1.065426] ACPI: PCI Interrupt Link [Z00J] enabled at IRQ 22
[ 1.065631] efifb: probing for efifb
[ 1.065658] efifb: framebuffer at 0x80010000, using 7232k, total 7232k
[ 1.065659] efifb: mode is 1440x900x32, linelength=8192, pages=1
[ 1.065660] efifb: scrolling: redraw
[ 1.065662] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 1.070890] Console: switching to colour frame buffer device 180x56
[ 1.075929] fb0: EFI VGA frame buffer device
[ 1.075940] intel_idle: does not run on family 6 model 23
[ 1.076040] Monitor-Mwait will be used to enter C-1 state
[ 1.076045] Monitor-Mwait will be used to enter C-2 state
[ 1.076050] Monitor-Mwait will be used to enter C-3 state
[ 1.076052] tsc: Marking TSC unstable due to TSC halts in idle
[ 1.076409] GHES: HEST is not enabled!
[ 1.076526] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.077472] rtc_cmos 00:03: RTC can wake from S4
[ 1.077786] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 1.077840] rtc_cmos 00:03: alarms up to one year, y3k, 242 bytes nvram, hpet irqs
[ 1.077906] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.077954] vlv2_plat_clk vlv2_plat_clk: vlv2_plat_clk initialized
[ 1.078270] NET: Registered protocol family 10
[ 1.082790] Segment Routing with IPv6
[ 1.082812] NET: Registered protocol family 17
[ 1.082951] RAS: Correctable Errors collector initialized.
[ 1.082986] microcode: sig=0x1067a, pf=0x80, revision=0xa07
[ 1.083048] microcode: Microcode Update Driver: v2.2.
[ 1.083231] registered taskstats version 1
[ 1.083244] Loading compiled-in X.509 certificates
[ 1.083259] zswap: loaded using pool lzo/zbud
[ 1.087010] Key type big_key registered
[ 1.087668] Magic number: 9:726:621
[ 1.087815] rtc_cmos 00:03: setting system clock to 2017-11-05 07:37:05 UTC (1509867425)
[ 1.088721] PM: Hibernation image not present or could not be loaded.
[ 1.091246] Freeing unused kernel memory: 1336K
[ 1.091248] Write protecting the kernel read-only data: 10240k
[ 1.092198] Freeing unused kernel memory: 1536K
[ 2.080024] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x359355a40ea, max_idle_ns: 881590542641 ns
[ 2.111256] ACPI: bus type USB registered
[ 2.111290] usbcore: registered new interface driver usbfs
[ 2.111303] usbcore: registered new interface driver hub
[ 2.111333] usbcore: registered new device driver usb
[ 2.111965] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.112505] ehci-pci: EHCI PCI platform driver
[ 2.112631] SCSI subsystem initialized
[ 2.112758] ehci-pci 0000:00:04.1: EHCI Host Controller
[ 2.112767] ehci-pci 0000:00:04.1: new USB bus registered, assigned bus number 1
[ 2.112779] ehci-pci 0000:00:04.1: debug port 1
[ 2.112803] ehci-pci 0000:00:04.1: disable ppcd for nvidia mcp89
[ 2.112810] ehci-pci 0000:00:04.1: cache line size of 256 is not supported
[ 2.112829] ehci-pci 0000:00:04.1: irq 23, io mem 0x9328b100
[ 2.113406] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.114826] libata version 3.00 loaded.
[ 2.123390] ehci-pci 0000:00:04.1: USB 2.0 started, EHCI 1.10
[ 2.123607] hub 1-0:1.0: USB hub found
[ 2.123616] hub 1-0:1.0: 6 ports detected
[ 2.124096] ehci-pci 0000:00:06.1: EHCI Host Controller
[ 2.124105] ehci-pci 0000:00:06.1: new USB bus registered, assigned bus number 2
[ 2.124114] ehci-pci 0000:00:06.1: debug port 1
[ 2.124134] ehci-pci 0000:00:06.1: disable ppcd for nvidia mcp89
[ 2.124140] ehci-pci 0000:00:06.1: cache line size of 256 is not supported
[ 2.124153] ehci-pci 0000:00:06.1: irq 19, io mem 0x9328b000
[ 2.136748] ehci-pci 0000:00:06.1: USB 2.0 started, EHCI 1.10
[ 2.136992] hub 2-0:1.0: USB hub found
[ 2.137001] hub 2-0:1.0: 6 ports detected
[ 2.137353] ahci 0000:00:0a.0: version 3.0
[ 2.137639] ohci-pci: OHCI PCI platform driver
[ 2.137667] ACPI: PCI Interrupt Link [LSI0] enabled at IRQ 18
[ 2.137745] ahci 0000:00:0a.0: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
[ 2.137748] ahci 0000:00:0a.0: flags: 64bit ncq sntf pm led pio slum part apst
[ 2.138296] scsi host0: ahci
[ 2.138381] ata1: SATA max UDMA/133 abar m8192@0x93284000 port 0x93284100 irq 24
[ 2.138537] ohci-pci 0000:00:04.0: OHCI PCI host controller
[ 2.138544] ohci-pci 0000:00:04.0: new USB bus registered, assigned bus number 3
[ 2.138562] ohci-pci 0000:00:04.0: irq 23, io mem 0x9328a000
[ 2.195676] hub 3-0:1.0: USB hub found
[ 2.195686] hub 3-0:1.0: 6 ports detected
[ 2.196113] ohci-pci 0000:00:06.0: OHCI PCI host controller
[ 2.196119] ohci-pci 0000:00:06.0: new USB bus registered, assigned bus number 4
[ 2.196141] ohci-pci 0000:00:06.0: irq 20, io mem 0x93289000
[ 2.252234] hub 4-0:1.0: USB hub found
[ 2.252244] hub 4-0:1.0: 6 ports detected
[ 2.451025] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.451264] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 2.451327] ata1.00: ATA-8: APPLE SSD TS128C, CJAA0201, max UDMA/100
[ 2.451330] ata1.00: 236978176 sectors, multi 16: LBA48
[ 2.451638] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 2.451702] ata1.00: configured for UDMA/100
[ 2.451946] scsi 0:0:0:0: Direct-Access ATA APPLE SSD TS128C 0201 PQ: 0 ANSI: 5
[ 2.460118] usb 2-1: new high-speed USB device number 2 using ehci-pci
[ 2.488441] sd 0:0:0:0: [sda] 236978176 512-byte logical blocks: (121 GB/113 GiB)
[ 2.488458] sd 0:0:0:0: [sda] Write Protect is off
[ 2.488461] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.488488] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.490543] sda: sda1 sda2 sda3 sda4 sda5
[ 2.491269] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.604477] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 2.605344] scsi host1: usb-storage 2-1:1.0
[ 2.605437] usbcore: registered new interface driver usb-storage
[ 2.605811] usbcore: registered new interface driver uas
[ 2.627685] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
[ 2.746702] usb 3-3: new full-speed USB device number 2 using ohci-pci
[ 2.751887] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 2.760897] systemd[1]: systemd 235 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN default-hierarchy=hybrid)
[ 2.761042] systemd[1]: Detected architecture x86-64.
[ 2.761702] systemd[1]: Set hostname to <arche>.
[ 2.879934] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 2.880178] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 2.880454] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 2.881170] systemd[1]: Created slice User and Session Slice.
[ 2.881489] systemd[1]: Created slice System Slice.
[ 2.886034] systemd[1]: Listening on udev Kernel Socket.
[ 2.886158] systemd[1]: Reached target Slices.
[ 2.959082] EXT4-fs (sda5): re-mounted. Opts: data=ordered
[ 3.032156] systemd-journald[184]: Received request to flush runtime journal from PID 1
[ 3.134637] ACPI: SBS HC: EC = 0xffff991868a0f500, offset = 0x20, query_bit = 0x10
[ 3.135001] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
[ 3.135047] ACPI: Lid Switch [LID0]
[ 3.135105] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[ 3.135118] ACPI: Power Button [PWRB]
[ 3.135172] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
[ 3.135183] ACPI: Sleep Button [SLPB]
[ 3.135263] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 3.135283] ACPI: Power Button [PWRF]
[ 3.135407] hidraw: raw HID events driver (C) Jiri Kosina
[ 3.143647] ACPI: AC Adapter [ADP1] (off-line)
[ 3.169463] usbcore: registered new interface driver usbhid
[ 3.169466] usbhid: USB HID core driver
[ 3.172532] [Firmware Bug]: ACPI(IGPU) defines _DOD but not _DOS
[ 3.172561] ACPI: Video Device [IGPU] (multi-head: yes rom: no post: no)
[ 3.172707] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:2a/LNXVIDEO:00/input/input4
[ 3.197497] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 3.200803] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 3.250234] bcma: bus0: Found chip with id 43224, rev 0x01 and package 0x08
[ 3.250251] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0)
[ 3.250263] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0)
[ 3.250285] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0)
[ 3.272319] Linux agpgart interface v0.103
[ 3.290191] snd_hda_intel 0000:00:08.0: enabling device (0000 -> 0002)
[ 3.290518] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 20
[ 3.290528] snd_hda_intel 0000:00:08.0: Disabling MSI
[ 3.290531] snd_hda_intel 0000:00:08.0: position_fix set to 1 for device 10de:cb89
[ 3.310570] bcma: bus0: Bus registered
[ 3.375333] applesmc: key=323 fan=1 temp=27 index=26 acc=0 lux=0 kbd=0
[ 3.375430] applesmc applesmc.768: hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
[ 3.388763] (NULL device *): hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
[ 3.388799] ACPI: Smart Battery System [SBS0]: Battery Slot [BAT0] (battery present)
[ 3.395325] intel_powerclamp: No package C-state available
[ 3.405784] Adding 4198396k swap on /dev/sda4. Priority:-1 extents:1 across:4198396k SSFS
[ 3.417558] input: bcm5974 as /devices/pci0000:00/0000:00:04.0/usb3/3-3/3-3:1.2/input/input6
[ 3.417585] usbcore: registered new interface driver bcm5974
[ 3.445113] input: Apple Inc. Apple Internal Keyboard / Trackpad as /devices/pci0000:00/0000:00:04.0/usb3/3-3/3-3:1.0/0003:05AC:0240.0001/input/input7
[ 3.445957] ACPI Warning: \_SB.PCI0.IXVE.IGPU._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20170531/nsarguments-95)
[ 3.446060] ACPI: \_SB_.PCI0.IXVE.IGPU: failed to evaluate _DSM
[ 3.446103] nouveau 0000:02:00.0: enabling device (0006 -> 0007)
[ 3.446324] ACPI: PCI Interrupt Link [LGPU] enabled at IRQ 16
[ 3.446418] checking generic (80010000 710000) vs hw (80000000 10000000)
[ 3.446419] fb: switching to nouveaufb from EFI VGA
[ 3.446451] Console: switching to colour dummy device 80x25
[ 3.446689] nouveau 0000:02:00.0: NVIDIA MCP89 (0af180a2)
[ 3.477821] nouveau 0000:02:00.0: bios: version 70.89.13.00.00
[ 3.500128] apple 0003:05AC:0240.0001: input,hidraw0: USB HID v1.11 Keyboard [Apple Inc. Apple Internal Keyboard / Trackpad] on usb-0000:00:04.0-3/input0
[ 3.500305] apple 0003:05AC:0240.0002: hidraw1: USB HID v1.11 Device [Apple Inc. Apple Internal Keyboard / Trackpad] on usb-0000:00:04.0-3/input1
[ 3.503868] nouveau 0000:02:00.0: fb: 256 MiB stolen system memory
[ 3.590232] nouveau 0000:02:00.0: bus: MMIO write of 0000807e FAULT at 100c1c
[ 3.672467] scsi 1:0:0:0: Direct-Access APPLE SD Card Reader 1.00 PQ: 0 ANSI: 0
[ 3.674189] sd 1:0:0:0: [sdb] Attached SCSI removable disk
[ 3.675740] mousedev: PS/2 mouse device common for all mice
[ 3.726706] usb 3-5: new full-speed USB device number 3 using ohci-pci
[ 3.868434] Support for cores revisions 0x17 and 0x18 disabled by module param allhwsupport=0. Try b43.allhwsupport=1
[ 3.868452] b43: probe of bcma0:1 failed with error -524
[ 3.877968] Broadcom 43xx driver loaded [ Features: PNLS ]
[ 3.912383] brcmsmac bcma0:1: mfg 4bf core 812 rev 23 class 0 irq 22
[ 3.933294] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 3.936735] brcmsmac bcma0:1 wlp1s0b1: renamed from wlan0
[ 3.959119] hub 3-5:1.0: USB hub found
[ 3.962066] hub 3-5:1.0: 3 ports detected
[ 4.213345] usb 1-6: new high-speed USB device number 4 using ehci-pci
[ 4.276710] usb 3-5.1: new full-speed USB device number 4 using ohci-pci
[ 4.405459] input: HID 05ac:820a as /devices/pci0000:00/0000:00:04.0/usb3/3-5/3-5.1/3-5.1:1.0/0003:05AC:820A.0003/input/input8
[ 4.460756] hid-generic 0003:05AC:820A.0003: input,hidraw2: USB HID v1.11 Keyboard [HID 05ac:820a] on usb-0000:00:04.0-5.1/input0
[ 4.483390] usb 3-5.2: new full-speed USB device number 5 using ohci-pci
[ 4.493389] snd_hda_codec_cirrus hdaudioC0D0: autoconfig for CS4206: line_outs=2 (0xb/0xa/0x0/0x0/0x0) type:speaker
[ 4.493392] snd_hda_codec_cirrus hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 4.493394] snd_hda_codec_cirrus hdaudioC0D0: hp_outs=1 (0x9/0x0/0x0/0x0/0x0)
[ 4.493396] snd_hda_codec_cirrus hdaudioC0D0: mono: mono_out=0x0
[ 4.493398] snd_hda_codec_cirrus hdaudioC0D0: dig-out=0x10/0x0
[ 4.493400] snd_hda_codec_cirrus hdaudioC0D0: inputs:
[ 4.493402] snd_hda_codec_cirrus hdaudioC0D0: Mic=0xd
[ 4.610545] input: HID 05ac:820b as /devices/pci0000:00/0000:00:04.0/usb3/3-5/3-5.2/3-5.2:1.0/0003:05AC:820B.0004/input/input9
[ 4.636740] media: Linux media interface: v0.10
[ 4.644421] Linux video capture interface: v2.00
[ 4.655333] uvcvideo: Found UVC 1.00 device Built-in iSight (05ac:850a)
[ 4.662904] uvcvideo 1-6:1.0: Entity type for entity Processing 3 was not initialized!
[ 4.662907] uvcvideo 1-6:1.0: Entity type for entity Camera 1 was not initialized!
[ 4.663182] input: Built-in iSight: Built-in iSigh as /devices/pci0000:00/0000:00:04.1/usb1/1-6/1-6:1.0/input/input10
[ 4.666837] hid-generic 0003:05AC:820B.0004: input,hidraw3: USB HID v1.11 Mouse [HID 05ac:820b] on usb-0000:00:04.0-5.2/input0
[ 4.670369] usbcore: registered new interface driver uvcvideo
[ 4.670371] USB Video Class driver (1.1.1)
[ 4.746708] usb 3-5.3: new full-speed USB device number 6 using ohci-pci
[ 4.780286] [TTM] Zone kernel: Available graphics memory: 894452 kiB
[ 4.780288] [TTM] Initializing pool allocator
[ 4.780294] [TTM] Initializing DMA pool allocator
[ 4.780319] nouveau 0000:02:00.0: DRM: VRAM: 256 MiB
[ 4.780321] nouveau 0000:02:00.0: DRM: GART: 1048576 MiB
[ 4.780326] nouveau 0000:02:00.0: DRM: TMDS table version 2.0
[ 4.780328] nouveau 0000:02:00.0: DRM: DCB version 4.0
[ 4.780331] nouveau 0000:02:00.0: DRM: DCB outp 00: 040001b6 0f220010
[ 4.780333] nouveau 0000:02:00.0: DRM: DCB outp 01: 020112a6 0f220010
[ 4.780335] nouveau 0000:02:00.0: DRM: DCB outp 02: 02011262 00020010
[ 4.780337] nouveau 0000:02:00.0: DRM: DCB conn 00: 00002047
[ 4.780339] nouveau 0000:02:00.0: DRM: DCB conn 01: 00101146
[ 4.785966] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 4.785967] [drm] Driver supports precise vblank timestamp query.
[ 4.801719] nouveau 0000:02:00.0: DRM: MM: using M2MF for buffer copies
[ 4.870637] nouveau 0000:02:00.0: DRM: allocated 1440x900 fb: 0x50000, bo ffff9918654c4000
[ 4.874697] fbcon: nouveaufb (fb0) is primary device
[ 4.927373] Bluetooth: Core ver 2.22
[ 4.927678] NET: Registered protocol family 31
[ 4.927679] Bluetooth: HCI device and connection manager initialized
[ 4.927684] Bluetooth: HCI socket layer initialized
[ 4.927687] Bluetooth: L2CAP socket layer initialized
[ 4.927694] Bluetooth: SCO socket layer initialized
[ 4.941337] usbcore: registered new interface driver btusb
[ 4.966087] usb 3-5.1: USB disconnect, device number 4
[ 5.000110] Console: switching to colour frame buffer device 180x56
[ 5.069098] Bluetooth: hci0: BCM: chip id 19 build 0848
[ 5.072096] Bluetooth: hci0: BCM: product 05ac:821b
[ 5.075095] Bluetooth: hci0: BCM: features 0x07
[ 5.093076] Bluetooth: hci0: ubuntu-0
[ 5.102601] nouveau 0000:02:00.0: fb0: nouveaufb frame buffer device
[ 5.110100] [drm] Initialized nouveau 1.3.1 20120801 for 0000:02:00.0 on minor 0
[ 5.190238] usb 3-5.2: USB disconnect, device number 5
[ 5.595331] input: HDA NVidia Headphone as /devices/pci0000:00/0000:00:08.0/sound/card0/input11
[ 5.595788] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:08.0/sound/card0/input12
[ 5.596205] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:08.0/sound/card0/input13
[ 5.596600] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:08.0/sound/card0/input14
[ 12.864219] random: crng init done
What do I have to do to fix the problem?
If I have to add any log-files, please tell me.
Thank you for your help.
EDIT2: removed error messages which are not depending of the broadcom-driver.
]]>