That's it, thanks a lot! I feel a bit stupid now, but it seems linux-lts is actually too old for this machine. iommu=soft barely changed anything, for the record.
Conclusion for anyone else stumbling on this:
* Lenovo Yoga 7 with Tiger Lake chipset
* NVME drive visible in installer
* Current linux-lts kernel (here 5.4.) is too old, use 5.10!
[ 1.706468] pci_bus 10000:e1: busn_res: can not insert [bus e1] under [bus 00-1f] (conflicts with (null) [bus 00-1f])
What if you add the boot parameter iommu=soft
Edit:
You could also try using linux 5.10.11 from the ALA which is used on the ISO that worked for you.
Here are the logs:
Healthy dmesg: https://pastebin.com/RePhSUZN
Healthy lsmod: https://pastebin.com/f2hy7end
Broken dmesg: https://pastebin.com/ZC0Sxn46
Broken lsmod: https://pastebin.com/MwsKXUNS
Thank you very much!
]]>I am setting up a brand new Lenovo Yoga 7. I shrunk the Windows install, disabled secure boot and everything seemed to work well. Unfortunately, the system can't boot, because the disk does not show up.
What I tried: I added "nvme_load=YES" to the kernel parameters, I added "vmd" to mkinitcpio.conf MODULES, I added modconf to HOOKS and removed autodetect (and I added lspci and nvme to BINARIES).
So far I am not making any progress.
I'm happy about any debugging hints (or solutions, haha) you can give me!
lspci in the live system says:
0000:00:00.0 Host bridge: Intel Corporation 11th Gen Core Processor Host Bridge/DRAM Registers (rev 01)
0000:00:02.0 VGA compatible controller: Intel Corporation UHD Graphics (rev 01)
0000:00:04.0 Signal processing controller: Intel Corporation Device 9a03 (rev 01)
0000:00:07.0 PCI bridge: Intel Corporation Tiger Lake-LP Thunderbolt PCI Express Root Port #0 (rev 01)
0000:00:07.1 PCI bridge: Intel Corporation Tiger Lake-LP Thunderbolt PCI Express Root Port #1 (rev 01)
0000:00:07.2 PCI bridge: Intel Corporation Tiger Lake-LP Thunderbolt PCI Express Root Port #2 (rev 01)
0000:00:07.3 PCI bridge: Intel Corporation Tiger Lake-LP Thunderbolt PCI Express Root Port #3 (rev 01)
0000:00:0a.0 Signal processing controller: Intel Corporation Device 9a0d (rev 01)
0000:00:0d.0 USB controller: Intel Corporation Tiger Lake-LP Thunderbolt USB Controller (rev 01)
0000:00:0d.2 USB controller: Intel Corporation Tiger Lake-LP Thunderbolt NHI #0 (rev 01)
0000:00:0d.3 USB controller: Intel Corporation Tiger Lake-LP Thunderbolt NHI #1 (rev 01)
0000:00:0e.0 RAID bus controller: Intel Corporation Volume Management Device NVMe RAID Controller
0000:00:12.0 Serial controller: Intel Corporation Tiger Lake-LP Integrated Sensor Hub (rev 20)
0000:00:14.0 USB controller: Intel Corporation Tiger Lake-LP USB 3.2 Gen 2x1 xHCI Host Controller (rev 20)
0000:00:14.2 RAM memory: Intel Corporation Tiger Lake-LP Shared SRAM (rev 20)
0000:00:14.3 Network controller: Intel Corporation Wi-Fi 6 AX201 (rev 20)
0000:00:15.0 Serial bus controller [0c80]: Intel Corporation Tiger Lake-LP Serial IO I2C Controller #0 (rev 20)
0000:00:15.1 Serial bus controller [0c80]: Intel Corporation Tiger Lake-LP Serial IO I2C Controller #1 (rev 20)
0000:00:16.0 Communication controller: Intel Corporation Tiger Lake-LP Management Engine Interface (rev 20)
0000:00:1d.0 System peripheral: Intel Corporation Device 09ab
0000:00:1e.0 Communication controller: Intel Corporation Tiger Lake-LP Serial IO UART Controller #0 (rev 20)
0000:00:1e.3 Serial bus controller [0c80]: Intel Corporation Tiger Lake-LP Serial IO SPI Controller #1 (rev 20)
0000:00:1f.0 ISA bridge: Intel Corporation Tiger Lake-LP LPC Controller (rev 20)
0000:00:1f.3 Multimedia audio controller: Intel Corporation Tiger Lake-LP Smart Sound Technology Audio Controller (rev 20)
0000:00:1f.4 SMBus: Intel Corporation Tiger Lake-LP SMBus Controller (rev 20)
0000:00:1f.5 Serial bus controller [0c80]: Intel Corporation Tiger Lake-LP SPI Controller (rev 20)
10000:e0:1d.0 PCI bridge: Intel Corporation Tiger Lake-LP PCI Express Root Port #9 (rev 20)
10000:e1:00.0 Non-Volatile memory controller: Sandisk Corp Device 5006
In the emergency shell of the installed system, the last line is just missing, but I also get only numeric codes for the devices:
0000:00:00.0 Class 0600: Device 8086:9a14 (rev 01)
0000:00:02.0 Class 0300: Device 8086:9a49 (rev 01)
0000:00:04.0 Class 1180: Device 8086:9a03 (rev 01)
0000:00:07.0 Class 0604: Device 8086:9a23 (rev 01)
0000:00:07.1 Class 0604: Device 8086:9a25 (rev 01)
0000:00:07.2 Class 0604: Device 8086:9a27 (rev 01)
0000:00:07.3 Class 0604: Device 8086:9a29 (rev 01)
0000:00:0a.0 Class 1180: Device 8086:9a0d (rev 01)
0000:00:0d.0 Class 0c03: Device 8086:9a13 (rev 01)
0000:00:0d.2 Class 0c03: Device 8086:9a1b (rev 01)
0000:00:0d.3 Class 0c03: Device 8086:9a1d (rev 01)
0000:00:0e.0 Class 0104: Device 8086:9a0b
0000:00:12.0 Class 0700: Device 8086:a0fc (rev 20)
0000:00:14.0 Class 0c03: Device 8086:a0ed (rev 20)
0000:00:14.2 Class 0500: Device 8086:a0ef (rev 20)
0000:00:14.3 Class 0280: Device 8086:a0f0 (rev 20)
0000:00:15.0 Class 0c80: Device 8086:a0e8 (rev 20)
0000:00:15.1 Class 0c80: Device 8086:a0e9 (rev 20)
0000:00:16.0 Class 0780: Device 8086:a0e0 (rev 20)
0000:00:1d.0 Class 0880: Device 8086:09ab
0000:00:1e.0 Class 0780: Device 8086:a0a8 (rev 20)
0000:00:1e.3 Class 0c80: Device 8086:a0ab (rev 20)
0000:00:1f.0 Class 0601: Device 8086:a082 (rev 20)
0000:00:1f.3 Class 0401: Device 8086:a0c8 (rev 20)
0000:00:1f.4 Class 0c05: Device 8086:a0a3 (rev 20)
0000:00:1f.5 Class 0c80: Device 8086:a0a4 (rev 20)
10000:00:1d.0 Class 0604: Device 8086:a0b0 (rev 20)
Some excerpts from dmesg:
libata version 3.00 loaded.
...
[ 9.476846] vmd 0000:00:0e.0: PCI host bridge to bus 10000:e0
[ 9.476848] pci_bus 10000:e0: root bus resource [bus e0-ff]
[ 9.476849] pci_bus 10000:e0: root bus resource [mem 0x50000000-0x51ffffff]
[ 9.476850] pci_bus 10000:e0: root bus resource [mem 0x605f102000-0x605f1fffff 64bit]
[ 9.476874] pci 10000:e0:1d.0: [8086:a0b0] type 01 class 0x060400
[ 9.476977] pci 10000:e0:1d.0: PME# supported from D0 D3hot D3cold
[ 9.477016] pci 10000:e0:1d.0: PTM enabled (root), 4ns granularity
[ 9.477061] pci 10000:e0:1d.0: Adding to iommu group 9
[ 9.477073] pci 10000:e0:1d.0: Primary bus is hard wired to 0
[ 9.477138] pci 10000:e1:00.0: [15b7:5006] type 00 class 0x010802
[ 9.477169] pci 10000:e1:00.0: reg 0x10: [mem 0x50000000-0x50003fff 64bit]
[ 9.477215] pci 10000:e1:00.0: reg 0x20: [mem 0x00000000-0x000000ff 64bit]
[ 9.477393] pci 10000:e1:00.0: Adding to iommu group 9
[ 9.477434] pci 10000:e0:1d.0: PCI bridge to [bus e1]
[ 9.477436] pci 10000:e0:1d.0: bridge window [io 0x0000-0x0fff]
[ 9.477438] pci 10000:e0:1d.0: bridge window [mem 0x50000000-0x500fffff]
[ 9.477444] pci 10000:e0:1d.0: Primary bus is hard wired to 0
[ 9.477452] pci 10000:e0:1d.0: BAR 14: assigned [mem 0x50000000-0x500fffff]
[ 9.477453] pci 10000:e0:1d.0: BAR 13: no space for [io size 0x1000]
[ 9.477454] pci 10000:e0:1d.0: BAR 13: failed to assign [io size 0x1000]
[ 9.477455] pci 10000:e1:00.0: BAR 0: assigned [mem 0x50000000-0x50003fff 64bit]
[ 9.477469] pci 10000:e1:00.0: BAR 4: assigned [mem 0x50004000-0x500040ff 64bit]
[ 9.477483] pci 10000:e0:1d.0: PCI bridge to [bus e1]
[ 9.477488] pci 10000:e0:1d.0: bridge window [mem 0x50000000-0x500fffff]
[ 9.477505] pcieport 10000:e0:1d.0: can't derive routing for PCI INT A
[ 9.477505] pcieport 10000:e0:1d.0: PCI INT A: no GSI
[ 9.477549] pcieport 10000:e0:1d.0: PME: Signaling with IRQ 184
[ 9.477670] nvme nvme0: pci function 10000:e1:00.0
[ 9.477686] vmd 0000:00:0e.0: Bound to PCI domain 10000
[ 9.477687] pcieport 10000:e0:1d.0: can't derive routing for PCI INT A
[ 9.477688] nvme 10000:e1:00.0: PCI INT A: no GSI
[ 9.487648] nvme nvme0: 8/0/0 default/read/poll queues
[ 9.492942] nvme0n1: p1 p2 p3 p4 p5
The broken system looks pretty similar. But I cannot find the libata-line anywhere. Is this significant?
[ 1.706251] vmd 0000:00:0e.0: PCI host bridge to bus 10000:00
[ 1.706253] pci_bus 10000:00: root bus resource [bus 00-1f]
[ 1.706253] pci_bus 10000:00: root bus resource [mem 0x50000000-0x51ffffff]
[ 1.706254] pci_bus 10000:00: root bus resource [mem 0x605f102000-0x605f1fffff 64bit]
[ 1.706268] pci 10000:00:1d.0: [8086:a0b0] type 01 class 0x060400
[ 1.706377] pci 10000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 1.706405] pci 10000:00:1d.0: PTM enabled (root), 4ns granularity
[ 1.706468] pci_bus 10000:e1: busn_res: can not insert [bus e1] under [bus 00-1f] (conflicts with (null) [bus 00-1f])
[ 1.706469] pci 10000:00:1d.0: PCI bridge to [bus e1]
[ 1.706471] pci 10000:00:1d.0: bridge window [io 0x0000-0x0fff]
[ 1.706473] pci 10000:00:1d.0: bridge window [mem 0x50000000-0x500fffff]
[ 1.706489] pci 10000:00:1d.0: BAR 14: assigned [mem 0x50000000-0x500fffff]
[ 1.706490] pci 10000:00:1d.0: BAR 13: no space for [io size 0x1000]
[ 1.706491] pci 10000:00:1d.0: BAR 13: failed to assign [io size 0x1000]
[ 1.706491] pci 10000:00:1d.0: PCI bridge to [bus e1]
[ 1.706496] pci 10000:00:1d.0: bridge window [mem 0x50000000-0x500fffff]
[ 1.706513] pcieport 10000:00:1d.0: can't derive routing for PCI INT A
[ 1.706513] pcieport 10000:00:1d.0: PCI INT A: no GSI
[ 1.706556] pcieport 10000:00:1d.0: PME: Signaling with IRQ 149
[ 1.706621] vmd 0000:00:0e.0: Bound to PCI domain 10000