iwconfig eth1 essid Csatlos
iwconfig eth1 key XXXXXXXX
After having used Kubuntu/PCLinuxOS and a host of other distros I wanted to give Arch a try on my Averatec 3280 laptop. All is well so far except the wireless connection. I have searched in this forum and on Google for answers but nothing has helped so far. My wireless is visible:
eth1 IEEE 802.11g ESSID:"Csatlos"
Mode:Managed Frequency:2.437 GHz Access Point: 00:0D:88:F2:53:E5
Bit Rate:54 Mb/s Tx-Power=20 dBm Sensitivity=8/0
Retry limit:7 RTS thr:off Fragment thr:off
Encryption key:95C0-xxxx-EBC3-xxxx-F699-xxxx-xx Security mode:restricted
Power Management:off
Link Quality=85/100 Signal level=-45 dBm Noise level=-85 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:1821 Missed beacon:2
ifconfig only shows eth0 and lo.
this is my /etc/rc.conf:
#
# /etc/rc.conf - Main Configuration for Arch Linux
#
#
# -----------------------------------------------------------------------
# LOCALIZATION
# -----------------------------------------------------------------------
#
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
#
LOCALE="en_US.utf8"
HARDWARECLOCK="localtime"
TIMEZONE="America/Eastern"
KEYMAP="us"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
#
# -----------------------------------------------------------------------
# HARDWARE
# -----------------------------------------------------------------------
#
# Scan hardware and load required modules at bootup
MOD_AUTOLOAD="yes"
# Module Blacklist - modules in this list will never be loaded by udev
MOD_BLACKLIST=()
#
# Modules to load at boot-up (in this order)
# - prefix a module with a ! to blacklist it
#
MODULES=(mii via-rhine ipw2200 ac97_bus snd-mixer-oss snd-pcm-oss snd-seq-oss snd-seq-device snd-seq-midi-event snd-seq snd-page-alloc snd-pcm snd-rawmidi snd-timer snd snd-mpu401-uart snd-ac97-codec snd-via82xx-modem snd-via82xx soundcore)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
#
# -----------------------------------------------------------------------
# NETWORKING
# -----------------------------------------------------------------------
#
HOSTNAME="csatlose-laptop"
#
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available
# interfaces.
#
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
#
# Note: to use DHCP, set your interface to be "dhcp" (eth0="dhcp")
#
lo="lo 127.0.0.1"
eth0="dhcp"
wlan_eth1="dhcp"
wlan_eth1="eth1 mode managed essid Csatlos key restricted 95c0xxxxebc3xxxxf699xxxxe6"
INTERFACES=(lo eth1 eth0)
#
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
#
gateway="default gw 192.168.4.1"
ROUTES=(!gateway)
#
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
#
# Network profiles are found in /etc/network-profiles
#
#NET_PROFILES=(main)
#
# -----------------------------------------------------------------------
# DAEMONS
# -----------------------------------------------------------------------
#
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
#
DAEMONS=(syslog-ng network netfs !networkmanager cups samba crond laptop-mode alsa ipw2200-fw wifi-radar)
# End of file
If you have any clue what I can do to get an IP address I would greatly appreciate it.
]]>