[solved] cannot clear the disk in UEFI install

crazySocket · 2018-01-20 23:13:15

I want to install Arch on my laptop with windows 10 preinstalled. The drive is encrypted. Gdisk presents two partitions: basic data partition and efi system partition. First is of size 32k, the second 12mb. Even though my drive is over 400gb there is no third partition to be seen neither can I use the space.

I replaced these partitions with new one. It seems I cannot use more than 128mb of the disc. I tried to create new empty GPT but even though gdisk prints "the operation has completed successfully" I can see lots of messages like this

ata1.00: exception emask 0x1 sact 0x0 serr 0x0 action 0x0
ata1.00: failed command: WRITE DMA

Any operation with gdisk or parted does not effect the hard drive.

Is there some kind of protection on? I had to disable secure boot in order to boot arch iso. I was following arch install guide. Yes, I verified I boot into uefi mode.

How can I partition such hard drive?

Last edited by crazySocket (2018-01-24 11:05:54)

Head_on_a_Stick · 2018-01-20 23:35:39

Try blkdiscard(8) (if it is an SSD) or see https://wiki.archlinux.org/index.php/Securely_wipe_disk

Otherwise, have you checked the firmware ("BIOS") menus for an option to disable the encryption?

Slithery · 2018-01-20 23:41:04

How is the drive encrypted?

R00KIE · 2018-01-21 01:16:45

Do you want to keep windows or do you want to wipe it all clean?

crazySocket · 2018-01-21 10:38:46

I want to wipe the drive clean. As far as I know the drive is encrypted with bitlocker. I have tried blkdiscard, hdparm (ata security erase) and dd (urandom). Seems like dd managed to write something down because windows does not boot anymore. However, every command results in kernel (?) printing the error message I presented in the first post.

I even tried to install debian with their fancy graphical installer. Failed on partitioning the disc, again.

Last edited by crazySocket (2018-01-21 11:02:37)

Head_on_a_Stick · 2018-01-21 11:40:46

crazySocket wrote:

the drive is encrypted with bitlocker

Does this help?

R00KIE · 2018-01-21 12:12:54

Please post the full output of dmesg, I begin to suspect that if the SSD is capable of self encryption that bitlocker may be using it.

Slithery · 2018-01-21 12:21:16

Also the output of...

hdparm -I /dev/sdX

crazySocket · 2018-01-21 18:30:09

hdparm -I /dev/sda

/dev/sda:

ATA device, with non-removable media
	Model Number:       LITEON CV3-8D512-41 SATA 512GB SED      
	Serial Number:      TW0MN0K7LOH0075R00AR
	Firmware Revision:  T89410C 
	Transport:          Serial, ATA8-AST, SATA II Extensions, SATA Rev 2.6, SATA Rev 3.0
Standards:
	Used: ATA/ATAPI-7 T13 1532D revision 4a 
	Supported: 8 7 6 5 & some of 8
Configuration:
	Logical		max	current
	cylinders	16383	16383
	heads		16	16
	sectors/track	63	63
	--
	CHS current addressable sectors:    16514064
	LBA    user addressable sectors:   268435455
	LBA48  user addressable sectors:  1000215216
	Logical  Sector size:                   512 bytes
	Physical Sector size:                   512 bytes
	Logical Sector-0 offset:                  0 bytes
	device size with M = 1024*1024:      488386 MBytes
	device size with M = 1000*1000:      512110 MBytes (512 GB)
	cache/buffer size  = unknown
	Form Factor: unknown (0x0007]
	Nominal Media Rotation Rate: Solid State Device
Capabilities:
	LBA, IORDY(can be disabled)
	Queue depth: 32
	Standby timer values: spec'd by Standard, no device specific minimum
	R/W multiple sector transfer: Max = 1	Current = 0
	Recommended acoustic management value: 254, current value: 0
	DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 
	     Cycle time: min=120ns recommended=120ns
	PIO: pio0 pio1 pio2 pio3 pio4 
	     Cycle time: no flow control=120ns  IORDY flow control=120ns
Commands/features:
	Enabled	Supported:
	   *	SMART feature set
	   *	Power Management feature set
	   *	Write cache
	   *	Look-ahead
	   *	Host Protected Area feature set
	   *	WRITE_BUFFER command
	   *	READ_BUFFER command
	   *	DOWNLOAD_MICROCODE
	    	SET_MAX security extension
	    	Automatic Acoustic Management feature set
	   *	48-bit Address feature set
	   *	Device Configuration Overlay feature set
	   *	Mandatory FLUSH_CACHE
	   *	FLUSH_CACHE_EXT
	   *	SMART error logging
	   *	SMART self-test
	   *	General Purpose Logging feature set
	   *	64-bit World wide name
	   *	Segmented DOWNLOAD_MICROCODE
	   *	Gen1 signaling speed (1.5Gb/s)
	   *	Gen2 signaling speed (3.0Gb/s)
	   *	Gen3 signaling speed (6.0Gb/s)
	   *	Native Command Queueing (NCQ)
	   *	Host-initiated interface power management
	   *	Phy event counters
	   *	DMA Setup Auto-Activate optimization
	    	Device-initiated interface power management
	   *	Software settings preservation
	   *	Device Sleep (DEVSLP)
	   *	SMART Command Transport (SCT) feature set
	   *	SCT Write Same (AC2)
	   *	SCT Error Recovery Control (AC3)
	   *	SCT Features Control (AC4)
	   *	SCT Data Tables (AC5)
	   *	SANITIZE_ANTIFREEZE_LOCK_EXT command
	   *	SANITIZE feature set
	   *	CRYPTO_SCRAMBLE_EXT command
	   *	BLOCK_ERASE_EXT command
	   *	reserved 69[4]
	   *	WRITE BUFFER DMA command
	   *	READ BUFFER DMA command
	   *	Data Set Management TRIM supported (limit 8 blocks)
Logical Unit WWN Device Identifier: 5002303100e7ef36
	NAA		: 5
	IEEE OUI	: 002303
	Unique ID	: 100e7ef36
Device Sleep:
	DEVSLP Exit Timeout (DETO): 100 ms (drive)
	Minimum DEVSLP Assertion Time (MDAT): 10 ms (drive)
Checksum: correct

dmesg

[    0.000000] Linux version 4.14.9-1-ARCH (builduser@heftig-13854) (gcc version 7.2.1 20171128 (GCC)) #1 SMP PREEMPT Tue Dec 26 00:18:37 UTC 2017
[    0.000000] Command line: initrd=\EFI\archiso\intel_ucode.img initrd=\EFI\archiso\archiso.img archisobasedir=arch archisolabel=ARCH_201801
[    0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[    0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[    0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
[    0.000000] x86/fpu: Supporting XSAVE feature 0x008: 'MPX bounds registers'
[    0.000000] x86/fpu: Supporting XSAVE feature 0x010: 'MPX CSR'
[    0.000000] x86/fpu: xstate_offset[2]:  576, xstate_sizes[2]:  256
[    0.000000] x86/fpu: xstate_offset[3]:  832, xstate_sizes[3]:   64
[    0.000000] x86/fpu: xstate_offset[4]:  896, xstate_sizes[4]:   64
[    0.000000] x86/fpu: Enabled xstate features 0x1f, context size is 960 bytes, using 'compacted' format.
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x0000000000057fff] usable
[    0.000000] BIOS-e820: [mem 0x0000000000058000-0x0000000000058fff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000059000-0x000000000009dfff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009e000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000006b2cefff] usable
[    0.000000] BIOS-e820: [mem 0x000000006b2cf000-0x000000006b2cffff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x000000006b2d0000-0x000000006b2d0fff] reserved
[    0.000000] BIOS-e820: [mem 0x000000006b2d1000-0x000000007a22dfff] usable
[    0.000000] BIOS-e820: [mem 0x000000007a22e000-0x000000007a5b7fff] reserved
[    0.000000] BIOS-e820: [mem 0x000000007a5b8000-0x000000007a5fefff] ACPI data
[    0.000000] BIOS-e820: [mem 0x000000007a5ff000-0x000000007af5ffff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x000000007af60000-0x000000007b5fefff] reserved
[    0.000000] BIOS-e820: [mem 0x000000007b5ff000-0x000000007b5fffff] usable
[    0.000000] BIOS-e820: [mem 0x000000007b600000-0x000000007f7fffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000f0000000-0x00000000f7ffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fe000000-0x00000000fe010fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000047e7fffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] e820: update [mem 0x6b380018-0x6b388e57] usable ==> usable
[    0.000000] e820: update [mem 0x6b380018-0x6b388e57] usable ==> usable
[    0.000000] e820: update [mem 0x65d1c018-0x65d2c457] usable ==> usable
[    0.000000] e820: update [mem 0x65d1c018-0x65d2c457] usable ==> usable
[    0.000000] extended physical RAM map:
[    0.000000] reserve setup_data: [mem 0x0000000000000000-0x0000000000057fff] usable
[    0.000000] reserve setup_data: [mem 0x0000000000058000-0x0000000000058fff] reserved
[    0.000000] reserve setup_data: [mem 0x0000000000059000-0x000000000009dfff] usable
[    0.000000] reserve setup_data: [mem 0x000000000009e000-0x00000000000fffff] reserved
[    0.000000] reserve setup_data: [mem 0x0000000000100000-0x0000000065d1c017] usable
[    0.000000] reserve setup_data: [mem 0x0000000065d1c018-0x0000000065d2c457] usable
[    0.000000] reserve setup_data: [mem 0x0000000065d2c458-0x000000006b2cefff] usable
[    0.000000] reserve setup_data: [mem 0x000000006b2cf000-0x000000006b2cffff] ACPI NVS
[    0.000000] reserve setup_data: [mem 0x000000006b2d0000-0x000000006b2d0fff] reserved
[    0.000000] reserve setup_data: [mem 0x000000006b2d1000-0x000000006b380017] usable
[    0.000000] reserve setup_data: [mem 0x000000006b380018-0x000000006b388e57] usable
[    0.000000] reserve setup_data: [mem 0x000000006b388e58-0x000000007a22dfff] usable
[    0.000000] reserve setup_data: [mem 0x000000007a22e000-0x000000007a5b7fff] reserved
[    0.000000] reserve setup_data: [mem 0x000000007a5b8000-0x000000007a5fefff] ACPI data
[    0.000000] reserve setup_data: [mem 0x000000007a5ff000-0x000000007af5ffff] ACPI NVS
[    0.000000] reserve setup_data: [mem 0x000000007af60000-0x000000007b5fefff] reserved
[    0.000000] reserve setup_data: [mem 0x000000007b5ff000-0x000000007b5fffff] usable
[    0.000000] reserve setup_data: [mem 0x000000007b600000-0x000000007f7fffff] reserved
[    0.000000] reserve setup_data: [mem 0x00000000f0000000-0x00000000f7ffffff] reserved
[    0.000000] reserve setup_data: [mem 0x00000000fe000000-0x00000000fe010fff] reserved
[    0.000000] reserve setup_data: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[    0.000000] reserve setup_data: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[    0.000000] reserve setup_data: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[    0.000000] reserve setup_data: [mem 0x0000000100000000-0x000000047e7fffff] usable
[    0.000000] efi: EFI v2.40 by American Megatrends
[    0.000000] efi:  ACPI=0x7a5c6000  ACPI 2.0=0x7a5c6000  SMBIOS=0xf0000  SMBIOS 3.0=0xf0020  ESRT=0x7b2d4018  MEMATTR=0x77bbf018 
[    0.000000] random: fast init done
[    0.000000] SMBIOS 3.0.0 present.
[    0.000000] DMI: Dell Inc. Latitude 5480/0DD5XR, BIOS 1.6.4 09/12/2017
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] e820: last_pfn = 0x47e800 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: write-back
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 0080000000 mask 7F80000000 uncachable
[    0.000000]   1 base 007E000000 mask 7FFE000000 uncachable
[    0.000000]   2 base 007D000000 mask 7FFF000000 uncachable
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000]   8 disabled
[    0.000000]   9 disabled
[    0.000000] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WP  UC- WT  
[    0.000000] e820: last_pfn = 0x7b600 max_arch_pfn = 0x400000000
[    0.000000] esrt: Reserving ESRT space from 0x000000007b2d4018 to 0x000000007b2d4050.
[    0.000000] Scanning 1 areas for low memory corruption
[    0.000000] Base memory trampoline at [ffff9171c0098000] 98000 size 24576
[    0.000000] Using GB pages for direct mapping
[    0.000000] BRK [0x34f212000, 0x34f212fff] PGTABLE
[    0.000000] BRK [0x34f213000, 0x34f213fff] PGTABLE
[    0.000000] BRK [0x34f214000, 0x34f214fff] PGTABLE
[    0.000000] BRK [0x34f215000, 0x34f215fff] PGTABLE
[    0.000000] BRK [0x34f216000, 0x34f216fff] PGTABLE
[    0.000000] BRK [0x34f217000, 0x34f217fff] PGTABLE
[    0.000000] BRK [0x34f218000, 0x34f218fff] PGTABLE
[    0.000000] BRK [0x34f219000, 0x34f219fff] PGTABLE
[    0.000000] BRK [0x34f21a000, 0x34f21afff] PGTABLE
[    0.000000] Secure boot disabled
[    0.000000] RAMDISK: [mem 0x65d2d000-0x67f5afff]
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x000000007A5C6000 000024 (v02 DELL  )
[    0.000000] ACPI: XSDT 0x000000007A5C60C8 000114 (v01 DELL   CBX3     01072009 AMI  00010013)
[    0.000000] ACPI: FACP 0x000000007A5EC630 00010C (v05 DELL   CBX3     01072009 AMI  00010013)
[    0.000000] ACPI: DSDT 0x000000007A5C6270 0263C0 (v02 DELL   CBX3     01072009 INTL 20160422)
[    0.000000] ACPI: FACS 0x000000007AF5DE80 000040
[    0.000000] ACPI: APIC 0x000000007A5EC740 000084 (v03 DELL   CBX3     01072009 AMI  00010013)
[    0.000000] ACPI: FPDT 0x000000007A5EC7C8 000044 (v01 DELL   CBX3     01072009 AMI  00010013)
[    0.000000] ACPI: FIDT 0x000000007A5EC810 0000AC (v01 DELL   CBX3     01072009 AMI  00010013)
[    0.000000] ACPI: MCFG 0x000000007A5EC8C0 00003C (v01 DELL   CBX3     01072009 MSFT 00000097)
[    0.000000] ACPI: HPET 0x000000007A5EC900 000038 (v01 DELL   CBX3     01072009 AMI. 0005000B)
[    0.000000] ACPI: SSDT 0x000000007A5EC938 000559 (v01 SataRe SataTabl 00001000 INTL 20160422)
[    0.000000] ACPI: SSDT 0x000000007A5ECE98 0012FE (v02 SaSsdt SaSsdt   00003000 INTL 20160422)
[    0.000000] ACPI: SSDT 0x000000007A5EE198 002AC0 (v02 PegSsd PegSsdt  00001000 INTL 20160422)
[    0.000000] ACPI: HPET 0x000000007A5F0C58 000038 (v01 INTEL  KBL      00000001 MSFT 0000005F)
[    0.000000] ACPI: SSDT 0x000000007A5F0C90 000CE8 (v02 INTEL  xh_rvp11 00000000 INTL 20160422)
[    0.000000] ACPI: UEFI 0x000000007A5F1978 000042 (v01                 00000000      00000000)
[    0.000000] ACPI: SSDT 0x000000007A5F19C0 000EDE (v02 CpuRef CpuSsdt  00003000 INTL 20160422)
[    0.000000] ACPI: LPIT 0x000000007A5F28A0 000094 (v01 INTEL  KBL      00000000 MSFT 0000005F)
[    0.000000] ACPI: WSMT 0x000000007A5F2938 000028 (v01 DELL   CBX3     00000000 MSFT 0000005F)
[    0.000000] ACPI: SSDT 0x000000007A5F2960 000141 (v02 INTEL  HdaDsp   00000000 INTL 20160422)
[    0.000000] ACPI: SSDT 0x000000007A5F2AA8 00029F (v02 INTEL  sensrhub 00000000 INTL 20160422)
[    0.000000] ACPI: SSDT 0x000000007A5F2D48 003002 (v02 INTEL  PtidDevc 00001000 INTL 20160422)
[    0.000000] ACPI: SSDT 0x000000007A5F5D50 000517 (v02 INTEL  TbtTypeC 00000000 INTL 20160422)
[    0.000000] ACPI: DBGP 0x000000007A5F6268 000034 (v01 INTEL           00000002 MSFT 0000005F)
[    0.000000] ACPI: DBG2 0x000000007A5F62A0 000054 (v00 INTEL           00000002 MSFT 0000005F)
[    0.000000] ACPI: SSDT 0x000000007A5F62F8 005265 (v02 DptfTa DptfTabl 00001000 INTL 20160422)
[    0.000000] ACPI: MSDM 0x000000007A5FB560 000055 (v03 DELL   CBX3     06222004 AMI  00010013)
[    0.000000] ACPI: SLIC 0x000000007A5FB5B8 000176 (v03 DELL   CBX3     01072009 MSFT 00010013)
[    0.000000] ACPI: SSDT 0x000000007A5FB730 00006A (v02 SgRef  SgPeg    00001000 INTL 20160422)
[    0.000000] ACPI: DMAR 0x000000007A5FB7A0 0000F0 (v01 INTEL  KBL      00000001 INTL 00000001)
[    0.000000] ACPI: TPM2 0x000000007A5FB890 000034 (v03        Tpm2Tabl 00000001 AMI  00000000)
[    0.000000] ACPI: SSDT 0x000000007A5FB8C8 001D77 (v01 ODMRef ODMTabl  00001000 INTL 20160422)
[    0.000000] ACPI: ASF! 0x000000007A5FD640 0000A0 (v32 INTEL   HCG     00000001 TFSM 000F4240)
[    0.000000] ACPI: BGRT 0x000000007A5FD6E0 000038 (v00 ?\xb7\xea|            01072009 AMI  00010013)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at [mem 0x0000000000000000-0x000000047e7fffff]
[    0.000000] NODE_DATA(0) allocated [mem 0x47e7fc000-0x47e7fffff]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.000000]   DMA32    [mem 0x0000000001000000-0x00000000ffffffff]
[    0.000000]   Normal   [mem 0x0000000100000000-0x000000047e7fffff]
[    0.000000]   Device   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000001000-0x0000000000057fff]
[    0.000000]   node   0: [mem 0x0000000000059000-0x000000000009dfff]
[    0.000000]   node   0: [mem 0x0000000000100000-0x000000006b2cefff]
[    0.000000]   node   0: [mem 0x000000006b2d1000-0x000000007a22dfff]
[    0.000000]   node   0: [mem 0x000000007b5ff000-0x000000007b5fffff]
[    0.000000]   node   0: [mem 0x0000000100000000-0x000000047e7fffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000047e7fffff]
[    0.000000] On node 0 totalpages: 4164041
[    0.000000]   DMA zone: 64 pages used for memmap
[    0.000000]   DMA zone: 21 pages reserved
[    0.000000]   DMA zone: 3996 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 7753 pages used for memmap
[    0.000000]   DMA32 zone: 496173 pages, LIFO batch:31
[    0.000000]   Normal zone: 57248 pages used for memmap
[    0.000000]   Normal zone: 3663872 pages, LIFO batch:31
[    0.000000] Reserving Intel graphics memory at 0x000000007d800000-0x000000007f7fffff
[    0.000000] ACPI: PM-Timer IO Port: 0x1808
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
[    0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-119
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[    0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[    0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.000000] PM: Registered nosave memory: [mem 0x00058000-0x00058fff]
[    0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x000fffff]
[    0.000000] PM: Registered nosave memory: [mem 0x65d1c000-0x65d1cfff]
[    0.000000] PM: Registered nosave memory: [mem 0x65d2c000-0x65d2cfff]
[    0.000000] PM: Registered nosave memory: [mem 0x6b2cf000-0x6b2cffff]
[    0.000000] PM: Registered nosave memory: [mem 0x6b2d0000-0x6b2d0fff]
[    0.000000] PM: Registered nosave memory: [mem 0x6b380000-0x6b380fff]
[    0.000000] PM: Registered nosave memory: [mem 0x6b388000-0x6b388fff]
[    0.000000] PM: Registered nosave memory: [mem 0x7a22e000-0x7a5b7fff]
[    0.000000] PM: Registered nosave memory: [mem 0x7a5b8000-0x7a5fefff]
[    0.000000] PM: Registered nosave memory: [mem 0x7a5ff000-0x7af5ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x7af60000-0x7b5fefff]
[    0.000000] PM: Registered nosave memory: [mem 0x7b600000-0x7f7fffff]
[    0.000000] PM: Registered nosave memory: [mem 0x7f800000-0xefffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xf0000000-0xf7ffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfdffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfe000000-0xfe010fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfe011000-0xfebfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfedfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xfeffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xff000000-0xffffffff]
[    0.000000] e820: [mem 0x7f800000-0xefffffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370452778343963 ns
[    0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:4 nr_node_ids:1
[    0.000000] percpu: Embedded 38 pages/cpu @ffff91763e400000 s117400 r8192 d30056 u524288
[    0.000000] pcpu-alloc: s117400 r8192 d30056 u524288 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 4098955
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: initrd=\EFI\archiso\intel_ucode.img initrd=\EFI\archiso\archiso.img archisobasedir=arch archisolabel=ARCH_201801
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Calgary: detecting Calgary via BIOS EBDA area
[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000000] Memory: 16230780K/16656164K available (6648K kernel code, 1149K rwdata, 2788K rodata, 1320K init, 992K bss, 425384K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] ftrace: allocating 29083 entries in 114 pages
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.
[    0.000000] 	Tasks RCU enabled.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 8448, nr_irqs: 1024, preallocated irqs: 16
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [tty0] enabled
[    0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635855245 ns
[    0.000000] hpet clockevent registered
[    0.003333] tsc: Detected 2800.000 MHz processor
[    0.003333] Calibrating delay loop (skipped), value calculated using timer frequency.. 5618.00 BogoMIPS (lpj=9360000)
[    0.003333] pid_max: default: 32768 minimum: 301
[    0.003333] ACPI: Core revision 20170728
[    0.046480] ACPI: 13 ACPI AML tables successfully acquired and loaded
[    0.047361] Security Framework initialized
[    0.047361] Yama: becoming mindful.
[    0.049727] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[    0.050934] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[    0.050976] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes)
[    0.051015] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes)
[    0.051206] CPU: Physical Processor ID: 0
[    0.051207] CPU: Processor Core ID: 0
[    0.051212] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[    0.051212] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[    0.051217] mce: CPU supports 10 MCE banks
[    0.051226] CPU0: Thermal monitoring enabled (TM1)
[    0.051247] process: using mwait in idle threads
[    0.051250] Last level iTLB entries: 4KB 128, 2MB 8, 4MB 8
[    0.051250] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 0, 1GB 4
[    0.051531] Freeing SMP alternatives memory: 24K
[    0.054380] smpboot: Max logical packages: 1
[    0.054384] DMAR: Host address width 39
[    0.054385] DMAR: DRHD base: 0x000000fed90000 flags: 0x0
[    0.054392] DMAR: dmar0: reg_base_addr fed90000 ver 1:0 cap 1c0000c40660462 ecap 19e2ff0505e
[    0.054393] DMAR: DRHD base: 0x000000fed91000 flags: 0x1
[    0.054397] DMAR: dmar1: reg_base_addr fed91000 ver 1:0 cap d2008c40660462 ecap f050da
[    0.054397] DMAR: RMRR base: 0x0000007a2fb000 end: 0x0000007a31afff
[    0.054398] DMAR: RMRR base: 0x0000007d000000 end: 0x0000007f7fffff
[    0.054399] DMAR: ANDD device: 1 name: \_SB.PCI0.I2C0
[    0.054400] DMAR: ANDD device: 2 name: \_SB.PCI0.I2C1
[    0.054401] DMAR-IR: IOAPIC id 2 under DRHD base  0xfed91000 IOMMU 1
[    0.054402] DMAR-IR: HPET id 0 under DRHD base 0xfed91000
[    0.054403] DMAR-IR: Queued invalidation will be enabled to support x2apic and Intr-remapping.
[    0.056958] DMAR-IR: Enabled IRQ remapping in x2apic mode
[    0.056961] x2apic enabled
[    0.056971] Switched APIC routing to cluster x2apic.
[    0.060923] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.093957] TSC deadline timer enabled
[    0.093961] smpboot: CPU0: Intel(R) Core(TM) i5-7440HQ CPU @ 2.80GHz (family: 0x6, model: 0x9e, stepping: 0x9)
[    0.106680] Performance Events: PEBS fmt3+, Skylake events, 32-deep LBR, full-width counters, Intel PMU driver.
[    0.106727] ... version:                4
[    0.106727] ... bit width:              48
[    0.106728] ... generic registers:      8
[    0.106729] ... value mask:             0000ffffffffffff
[    0.106729] ... max period:             00007fffffffffff
[    0.106729] ... fixed-purpose events:   3
[    0.106730] ... event mask:             00000007000000ff
[    0.113338] Hierarchical SRCU implementation.
[    0.126754] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[    0.133338] smp: Bringing up secondary CPUs ...
[    0.160034] x86: Booting SMP configuration:
[    0.160035] .... node  #0, CPUs:      #1 #2 #3
[    0.214066] smp: Brought up 1 node, 4 CPUs
[    0.214066] smpboot: Total of 4 processors activated (22472.00 BogoMIPS)
[    0.216944] devtmpfs: initialized
[    0.216944] x86/mm: Memory block size: 128MB
[    0.217692] PM: Registering ACPI NVS region [mem 0x6b2cf000-0x6b2cffff] (4096 bytes)
[    0.217692] PM: Registering ACPI NVS region [mem 0x7a5ff000-0x7af5ffff] (9834496 bytes)
[    0.217692] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    0.217692] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.217692] pinctrl core: initialized pinctrl subsystem
[    0.217692] RTC time: 18:17:43, date: 01/21/18
[    0.217692] NET: Registered protocol family 16
[    0.217692] cpuidle: using governor ladder
[    0.217692] cpuidle: using governor menu
[    0.217692] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.217692] ACPI: bus type PCI registered
[    0.217692] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.217692] PCI: MMCONFIG for domain 0000 [bus 00-7f] at [mem 0xf0000000-0xf7ffffff] (base 0xf0000000)
[    0.217692] PCI: MMCONFIG at [mem 0xf0000000-0xf7ffffff] reserved in E820
[    0.217692] PCI: Using configuration type 1 for base access
[    0.217692] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    0.217692] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.217692] ACPI: Added _OSI(Module Device)
[    0.217692] ACPI: Added _OSI(Processor Device)
[    0.217692] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.217692] ACPI: Added _OSI(Processor Aggregator Device)
[    0.220990] ACPI: Executed 40 blocks of module-level executable AML code
[    0.236775] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[    0.245499] ACPI: Dynamic OEM Table Load:
[    0.245506] ACPI: SSDT 0xFFFF91762B4C4000 000651 (v02 PmRef  Cpu0Ist  00003000 INTL 20160422)
[    0.245668] ACPI: Executed 1 blocks of module-level executable AML code
[    0.245738] ACPI: \_PR_.CPU0: _OSC native thermal LVT Acked
[    0.246692] ACPI: Dynamic OEM Table Load:
[    0.246698] ACPI: SSDT 0xFFFF91762B623400 0003FF (v02 PmRef  Cpu0Cst  00003001 INTL 20160422)
[    0.246840] ACPI: Executed 1 blocks of module-level executable AML code
[    0.247245] ACPI: Dynamic OEM Table Load:
[    0.247251] ACPI: SSDT 0xFFFF91762B4C5000 00065C (v02 PmRef  ApIst    00003000 INTL 20160422)
[    0.247595] ACPI: Executed 1 blocks of module-level executable AML code
[    0.247801] ACPI: Dynamic OEM Table Load:
[    0.247806] ACPI: SSDT 0xFFFF91762B554600 00018A (v02 PmRef  ApCst    00003000 INTL 20160422)
[    0.247947] ACPI: Executed 1 blocks of module-level executable AML code
[    0.249301] ACPI: EC: EC started
[    0.249302] ACPI: EC: interrupt blocked
[    0.255773] ACPI: \_SB_.PCI0.LPCB.ECDV: Used as first EC
[    0.255775] ACPI: \_SB_.PCI0.LPCB.ECDV: GPE=0x6e, EC_CMD/EC_SC=0x934, EC_DATA=0x930
[    0.255776] ACPI: \_SB_.PCI0.LPCB.ECDV: Used as boot DSDT EC to handle transactions
[    0.255776] ACPI: Interpreter enabled
[    0.255824] ACPI: (supports S0 S3 S4 S5)
[    0.255825] ACPI: Using IOAPIC for interrupt routing
[    0.255863] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.256506] ACPI: Enabled 8 GPEs in block 00 to 7F
[    0.258654] ACPI: Power Resource [PG00] (on)
[    0.259091] ACPI: Power Resource [PG01] (on)
[    0.280747] ACPI: Power Resource [PG02] (on)
[    0.282504] ACPI: Power Resource [WRST] (on)
[    0.282851] ACPI: Power Resource [WRST] (on)
[    0.283198] ACPI: Power Resource [WRST] (on)
[    0.283540] ACPI: Power Resource [WRST] (on)
[    0.283876] ACPI: Power Resource [WRST] (on)
[    0.284211] ACPI: Power Resource [WRST] (on)
[    0.284909] ACPI: Power Resource [WRST] (on)
[    0.285254] ACPI: Power Resource [WRST] (on)
[    0.285588] ACPI: Power Resource [WRST] (on)
[    0.285930] ACPI: Power Resource [WRST] (on)
[    0.286451] ACPI: Power Resource [WRST] (on)
[    0.286795] ACPI: Power Resource [WRST] (on)
[    0.287131] ACPI: Power Resource [WRST] (on)
[    0.287464] ACPI: Power Resource [WRST] (on)
[    0.287797] ACPI: Power Resource [WRST] (on)
[    0.288131] ACPI: Power Resource [WRST] (on)
[    0.288465] ACPI: Power Resource [WRST] (on)
[    0.289732] ACPI: Power Resource [WRST] (on)
[    0.290069] ACPI: Power Resource [WRST] (on)
[    0.290403] ACPI: Power Resource [WRST] (on)
[    0.311626] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-7e])
[    0.311631] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.311977] acpi PNP0A08:00: _OSC: platform does not support [PCIeHotplug PME]
[    0.312300] acpi PNP0A08:00: _OSC: OS now controls [AER PCIeCapability]
[    0.312301] acpi PNP0A08:00: FADT indicates ASPM is unsupported, using BIOS configuration
[    0.312930] PCI host bridge to bus 0000:00
[    0.312932] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
[    0.312933] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.312934] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.312935] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000c3fff window]
[    0.312936] pci_bus 0000:00: root bus resource [mem 0x000c4000-0x000c7fff window]
[    0.312937] pci_bus 0000:00: root bus resource [mem 0x000c8000-0x000cbfff window]
[    0.312937] pci_bus 0000:00: root bus resource [mem 0x000cc000-0x000cffff window]
[    0.312938] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff window]
[    0.312939] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff window]
[    0.312940] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff window]
[    0.312941] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff window]
[    0.312942] pci_bus 0000:00: root bus resource [mem 0x7f800000-0xefffffff window]
[    0.312943] pci_bus 0000:00: root bus resource [mem 0xfd000000-0xfe7fffff window]
[    0.312944] pci_bus 0000:00: root bus resource [bus 00-7e]
[    0.312951] pci 0000:00:00.0: [8086:5910] type 00 class 0x060000
[    0.313064] pci 0000:00:01.0: [8086:1901] type 01 class 0x060400
[    0.313103] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.313247] pci 0000:00:01.1: [8086:1905] type 01 class 0x060400
[    0.313285] pci 0000:00:01.1: PME# supported from D0 D3hot D3cold
[    0.313441] pci 0000:00:02.0: [8086:591b] type 00 class 0x030000
[    0.313451] pci 0000:00:02.0: reg 0x10: [mem 0xeb000000-0xebffffff 64bit]
[    0.313457] pci 0000:00:02.0: reg 0x18: [mem 0x80000000-0x8fffffff 64bit pref]
[    0.313461] pci 0000:00:02.0: reg 0x20: [io  0xf000-0xf03f]
[    0.313474] pci 0000:00:02.0: BAR 2: assigned to efifb
[    0.313585] pci 0000:00:04.0: [8086:1903] type 00 class 0x118000
[    0.313595] pci 0000:00:04.0: reg 0x10: [mem 0xed340000-0xed347fff 64bit]
[    0.313793] pci 0000:00:14.0: [8086:a12f] type 00 class 0x0c0330
[    0.313826] pci 0000:00:14.0: reg 0x10: [mem 0xed330000-0xed33ffff 64bit]
[    0.313927] pci 0000:00:14.0: PME# supported from D3hot D3cold
[    0.314125] pci 0000:00:14.2: [8086:a131] type 00 class 0x118000
[    0.314153] pci 0000:00:14.2: reg 0x10: [mem 0xed358000-0xed358fff 64bit]
[    0.314402] pci 0000:00:15.0: [8086:a160] type 00 class 0x118000
[    0.314653] pci 0000:00:15.0: reg 0x10: [mem 0xed357000-0xed357fff 64bit]
[    0.315533] pci 0000:00:15.1: [8086:a161] type 00 class 0x118000
[    0.315784] pci 0000:00:15.1: reg 0x10: [mem 0xed356000-0xed356fff 64bit]
[    0.316566] pci 0000:00:16.0: [8086:a13a] type 00 class 0x078000
[    0.316586] pci 0000:00:16.0: reg 0x10: [mem 0xed355000-0xed355fff 64bit]
[    0.316665] pci 0000:00:16.0: PME# supported from D3hot
[    0.316809] pci 0000:00:17.0: [8086:a102] type 00 class 0x010601
[    0.316834] pci 0000:00:17.0: reg 0x10: [mem 0xed350000-0xed351fff]
[    0.316841] pci 0000:00:17.0: reg 0x14: [mem 0xed354000-0xed3540ff]
[    0.316849] pci 0000:00:17.0: reg 0x18: [io  0xf090-0xf097]
[    0.316860] pci 0000:00:17.0: reg 0x1c: [io  0xf080-0xf083]
[    0.316869] pci 0000:00:17.0: reg 0x20: [io  0xf060-0xf07f]
[    0.316875] pci 0000:00:17.0: reg 0x24: [mem 0xed353000-0xed3537ff]
[    0.316929] pci 0000:00:17.0: PME# supported from D3hot
[    0.317068] pci 0000:00:1c.0: [8086:a111] type 01 class 0x060400
[    0.317163] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.317324] pci 0000:00:1c.2: [8086:a112] type 01 class 0x060400
[    0.317425] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[    0.317578] pci 0000:00:1c.4: [8086:a114] type 01 class 0x060400
[    0.317674] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[    0.317845] pci 0000:00:1f.0: [8086:a154] type 00 class 0x060100
[    0.318048] pci 0000:00:1f.2: [8086:a121] type 00 class 0x058000
[    0.318061] pci 0000:00:1f.2: reg 0x10: [mem 0xed34c000-0xed34ffff]
[    0.318228] pci 0000:00:1f.3: [8086:a171] type 00 class 0x040300
[    0.318258] pci 0000:00:1f.3: reg 0x10: [mem 0xed348000-0xed34bfff 64bit]
[    0.318284] pci 0000:00:1f.3: reg 0x20: [mem 0xed320000-0xed32ffff 64bit]
[    0.318337] pci 0000:00:1f.3: PME# supported from D3hot D3cold
[    0.318531] pci 0000:00:1f.4: [8086:a123] type 00 class 0x0c0500
[    0.318593] pci 0000:00:1f.4: reg 0x10: [mem 0xed352000-0xed3520ff 64bit]
[    0.318664] pci 0000:00:1f.4: reg 0x20: [io  0xf040-0xf05f]
[    0.318861] pci 0000:00:1f.6: [8086:15e3] type 00 class 0x020000
[    0.318890] pci 0000:00:1f.6: reg 0x10: [mem 0xed300000-0xed31ffff]
[    0.319004] pci 0000:00:1f.6: PME# supported from D0 D3hot D3cold
[    0.319149] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.319197] pci 0000:02:00.0: [10de:134e] type 00 class 0x030200
[    0.319225] pci 0000:02:00.0: reg 0x10: [mem 0xec000000-0xecffffff]
[    0.319242] pci 0000:02:00.0: reg 0x14: [mem 0xc0000000-0xcfffffff 64bit pref]
[    0.319259] pci 0000:02:00.0: reg 0x1c: [mem 0xd0000000-0xd1ffffff 64bit pref]
[    0.319270] pci 0000:02:00.0: reg 0x24: [io  0xe000-0xe07f]
[    0.319281] pci 0000:02:00.0: reg 0x30: [mem 0xed000000-0xed07ffff pref]
[    0.326709] pci 0000:00:01.1: PCI bridge to [bus 02]
[    0.326711] pci 0000:00:01.1:   bridge window [io  0xe000-0xefff]
[    0.326713] pci 0000:00:01.1:   bridge window [mem 0xec000000-0xed0fffff]
[    0.326716] pci 0000:00:01.1:   bridge window [mem 0xc0000000-0xd1ffffff 64bit pref]
[    0.327262] pci 0000:03:00.0: [8086:24fd] type 00 class 0x028000
[    0.327424] pci 0000:03:00.0: reg 0x10: [mem 0xed200000-0xed201fff 64bit]
[    0.327777] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
[    0.337001] pci 0000:00:1c.0: PCI bridge to [bus 03]
[    0.337008] pci 0000:00:1c.0:   bridge window [mem 0xed200000-0xed2fffff]
[    0.337171] pci 0000:04:00.0: [10ec:525a] type 00 class 0xff0000
[    0.337273] pci 0000:04:00.0: reg 0x14: [mem 0xed100000-0xed100fff]
[    0.337573] pci 0000:04:00.0: supports D1 D2
[    0.337574] pci 0000:04:00.0: PME# supported from D1 D2 D3hot D3cold
[    0.346754] pci 0000:00:1c.2: PCI bridge to [bus 04]
[    0.346761] pci 0000:00:1c.2:   bridge window [mem 0xed100000-0xed1fffff]
[    0.346894] pci 0000:00:1c.4: PCI bridge to [bus 05-3d]
[    0.346901] pci 0000:00:1c.4:   bridge window [mem 0xd4000000-0xea0fffff]
[    0.346908] pci 0000:00:1c.4:   bridge window [mem 0x90000000-0xb1ffffff 64bit pref]
[    0.351735] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.351783] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 *10 11 12 14 15)
[    0.351829] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.351874] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.351919] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.351965] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.352009] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.352054] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.354339] ACPI: EC: interrupt unblocked
[    0.354348] ACPI: EC: event unblocked
[    0.354370] ACPI: \_SB_.PCI0.LPCB.ECDV: GPE=0x6e, EC_CMD/EC_SC=0x934, EC_DATA=0x930
[    0.354371] ACPI: \_SB_.PCI0.LPCB.ECDV: Used as boot DSDT EC to handle transactions and events
[    0.354608] pci 0000:00:02.0: vgaarb: setting as boot VGA device
[    0.354608] pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[    0.354608] pci 0000:00:02.0: vgaarb: bridge control possible
[    0.354608] vgaarb: loaded
[    0.354608] EDAC MC: Ver: 3.0.0
[    0.354608] Registered efivars operations
[    0.364758] PCI: Using ACPI for IRQ routing
[    0.374940] PCI: pci_cache_line_size set to 64 bytes
[    0.375600] e820: reserve RAM buffer [mem 0x00058000-0x0005ffff]
[    0.375601] e820: reserve RAM buffer [mem 0x0009e000-0x0009ffff]
[    0.375602] e820: reserve RAM buffer [mem 0x65d1c018-0x67ffffff]
[    0.375603] e820: reserve RAM buffer [mem 0x6b2cf000-0x6bffffff]
[    0.375604] e820: reserve RAM buffer [mem 0x6b380018-0x6bffffff]
[    0.375604] e820: reserve RAM buffer [mem 0x7a22e000-0x7bffffff]
[    0.375605] e820: reserve RAM buffer [mem 0x7b600000-0x7bffffff]
[    0.375606] e820: reserve RAM buffer [mem 0x47e800000-0x47fffffff]
[    0.375671] NetLabel: Initializing
[    0.375671] NetLabel:  domain hash size = 128
[    0.375672] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.375684] NetLabel:  unlabeled traffic allowed by default
[    0.375693] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[    0.375693] hpet0: 8 comparators, 64-bit 24.000000 MHz counter
[    0.377694] clocksource: Switched to clocksource hpet
[    0.384433] VFS: Disk quotas dquot_6.6.0
[    0.384452] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.384495] pnp: PnP ACPI init
[    0.384718] system 00:00: [io  0x0680-0x069f] has been reserved
[    0.384720] system 00:00: [io  0xffff] has been reserved
[    0.384721] system 00:00: [io  0xffff] has been reserved
[    0.384722] system 00:00: [io  0xffff] has been reserved
[    0.384723] system 00:00: [io  0x1800-0x18fe] has been reserved
[    0.384724] system 00:00: [io  0x164e-0x164f] has been reserved
[    0.384728] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.384824] system 00:01: [io  0x0800-0x087f] has been reserved
[    0.384826] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.384842] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.384872] system 00:03: [io  0x1854-0x1857] has been reserved
[    0.384874] system 00:03: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[    0.384974] pnp 00:04: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.385187] system 00:05: [mem 0xfed10000-0xfed17fff] has been reserved
[    0.385188] system 00:05: [mem 0xfed18000-0xfed18fff] has been reserved
[    0.385190] system 00:05: [mem 0xfed19000-0xfed19fff] has been reserved
[    0.385191] system 00:05: [mem 0xf0000000-0xf7ffffff] has been reserved
[    0.385192] system 00:05: [mem 0xfed20000-0xfed3ffff] has been reserved
[    0.385193] system 00:05: [mem 0xfed90000-0xfed93fff] could not be reserved
[    0.385194] system 00:05: [mem 0xfed45000-0xfed8ffff] has been reserved
[    0.385196] system 00:05: [mem 0xff000000-0xffffffff] has been reserved
[    0.385197] system 00:05: [mem 0xfee00000-0xfeefffff] could not be reserved
[    0.385198] system 00:05: [mem 0xeffe0000-0xefffffff] has been reserved
[    0.385201] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.385235] system 00:06: [mem 0xfd000000-0xfdabffff] has been reserved
[    0.385236] system 00:06: [mem 0xfdad0000-0xfdadffff] has been reserved
[    0.385237] system 00:06: [mem 0xfdb00000-0xfdffffff] has been reserved
[    0.385238] system 00:06: [mem 0xfe000000-0xfe01ffff] could not be reserved
[    0.385240] system 00:06: [mem 0xfe036000-0xfe03bfff] has been reserved
[    0.385241] system 00:06: [mem 0xfe03d000-0xfe3fffff] has been reserved
[    0.385242] system 00:06: [mem 0xfe410000-0xfe7fffff] has been reserved
[    0.385244] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.385562] system 00:07: [io  0xff00-0xfffe] has been reserved
[    0.385564] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.386769] system 00:08: [mem 0xfdaf0000-0xfdafffff] has been reserved
[    0.386770] system 00:08: [mem 0xfdae0000-0xfdaeffff] has been reserved
[    0.386771] system 00:08: [mem 0xfdac0000-0xfdacffff] has been reserved
[    0.386774] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.392532] pnp: PnP ACPI: found 9 devices
[    0.400408] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.400450] pci 0000:00:1c.4: bridge window [io  0x1000-0x0fff] to [bus 05-3d] add_size 1000
[    0.400455] pci 0000:00:1c.4: BAR 13: assigned [io  0x2000-0x2fff]
[    0.400456] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.400462] pci 0000:00:01.1: PCI bridge to [bus 02]
[    0.400464] pci 0000:00:01.1:   bridge window [io  0xe000-0xefff]
[    0.400466] pci 0000:00:01.1:   bridge window [mem 0xec000000-0xed0fffff]
[    0.400468] pci 0000:00:01.1:   bridge window [mem 0xc0000000-0xd1ffffff 64bit pref]
[    0.400471] pci 0000:00:1c.0: PCI bridge to [bus 03]
[    0.400477] pci 0000:00:1c.0:   bridge window [mem 0xed200000-0xed2fffff]
[    0.400487] pci 0000:00:1c.2: PCI bridge to [bus 04]
[    0.400492] pci 0000:00:1c.2:   bridge window [mem 0xed100000-0xed1fffff]
[    0.400502] pci 0000:00:1c.4: PCI bridge to [bus 05-3d]
[    0.400506] pci 0000:00:1c.4:   bridge window [io  0x2000-0x2fff]
[    0.400511] pci 0000:00:1c.4:   bridge window [mem 0xd4000000-0xea0fffff]
[    0.400515] pci 0000:00:1c.4:   bridge window [mem 0x90000000-0xb1ffffff 64bit pref]
[    0.400523] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
[    0.400524] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
[    0.400525] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.400525] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000c3fff window]
[    0.400526] pci_bus 0000:00: resource 8 [mem 0x000c4000-0x000c7fff window]
[    0.400527] pci_bus 0000:00: resource 9 [mem 0x000c8000-0x000cbfff window]
[    0.400528] pci_bus 0000:00: resource 10 [mem 0x000cc000-0x000cffff window]
[    0.400529] pci_bus 0000:00: resource 11 [mem 0x000d0000-0x000d3fff window]
[    0.400530] pci_bus 0000:00: resource 12 [mem 0x000d4000-0x000d7fff window]
[    0.400531] pci_bus 0000:00: resource 13 [mem 0x000d8000-0x000dbfff window]
[    0.400532] pci_bus 0000:00: resource 14 [mem 0x000dc000-0x000dffff window]
[    0.400533] pci_bus 0000:00: resource 15 [mem 0x7f800000-0xefffffff window]
[    0.400534] pci_bus 0000:00: resource 16 [mem 0xfd000000-0xfe7fffff window]
[    0.400535] pci_bus 0000:02: resource 0 [io  0xe000-0xefff]
[    0.400536] pci_bus 0000:02: resource 1 [mem 0xec000000-0xed0fffff]
[    0.400537] pci_bus 0000:02: resource 2 [mem 0xc0000000-0xd1ffffff 64bit pref]
[    0.400538] pci_bus 0000:03: resource 1 [mem 0xed200000-0xed2fffff]
[    0.400539] pci_bus 0000:04: resource 1 [mem 0xed100000-0xed1fffff]
[    0.400540] pci_bus 0000:05: resource 0 [io  0x2000-0x2fff]
[    0.400540] pci_bus 0000:05: resource 1 [mem 0xd4000000-0xea0fffff]
[    0.400541] pci_bus 0000:05: resource 2 [mem 0x90000000-0xb1ffffff 64bit pref]
[    0.400678] NET: Registered protocol family 2
[    0.400798] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.400963] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.401084] TCP: Hash tables configured (established 131072 bind 65536)
[    0.401120] UDP hash table entries: 8192 (order: 6, 262144 bytes)
[    0.401160] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
[    0.401216] NET: Registered protocol family 1
[    0.401230] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[    0.401821] PCI: CLS 0 bytes, default 64
[    0.401849] Unpacking initramfs...
[    4.099198] Freeing initrd memory: 35000K
[    4.099227] DMAR: ACPI device "device:79" under DMAR at fed91000 as 00:15.0
[    4.099230] DMAR: ACPI device "device:7a" under DMAR at fed91000 as 00:15.1
[    4.099243] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    4.099245] software IO TLB [mem 0x73140000-0x77140000] (64MB) mapped at [ffff917233140000-ffff91723713ffff]
[    4.099387] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2879c5f06f2, max_idle_ns: 440795220049 ns
[    4.099514] Scanning for low memory corruption every 60 seconds
[    4.100107] Initialise system trusted keyrings
[    4.100114] Key type blacklist registered
[    4.100187] workingset: timestamp_bits=41 max_order=22 bucket_order=0
[    4.101026] zbud: loaded
[    4.103740] Key type asymmetric registered
[    4.103771] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    4.103824] io scheduler noop registered
[    4.103825] io scheduler deadline registered
[    4.103858] io scheduler cfq registered (default)
[    4.103859] io scheduler mq-deadline registered
[    4.103859] io scheduler kyber registered
[    4.103876] io scheduler bfq registered
[    4.105007] pcieport 0000:00:1c.0: AER enabled with IRQ 122
[    4.105037] pcieport 0000:00:1c.2: AER enabled with IRQ 123
[    4.105070] pcieport 0000:00:1c.4: AER enabled with IRQ 124
[    4.105090] efifb: probing for efifb
[    4.105100] efifb: framebuffer at 0x80000000, using 1876k, total 1875k
[    4.105101] efifb: mode is 800x600x32, linelength=3200, pages=1
[    4.105101] efifb: scrolling: redraw
[    4.105102] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[    4.106082] Console: switching to colour frame buffer device 100x37
[    4.106991] fb0: EFI VGA frame buffer device
[    4.106998] intel_idle: MWAIT substates: 0x11142120
[    4.106999] intel_idle: v0.4.1 model 0x9E
[    4.107196] intel_idle: lapic_timer_reliable_states 0xffffffff
[    4.107432] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    4.108402] rtc_cmos 00:02: RTC can wake from S4
[    4.108826] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[    4.108910] rtc_cmos 00:02: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[    4.108916] intel_pstate: Intel P-state driver initializing
[    4.108944] intel_pstate: Disabling energy efficiency optimization
[    4.109351] intel_pstate: HWP enabled
[    4.109468] ledtrig-cpu: registered to indicate activity on CPUs
[    4.109509] vlv2_plat_clk vlv2_plat_clk: vlv2_plat_clk initialized
[    4.109650] NET: Registered protocol family 10
[    4.113098] Segment Routing with IPv6
[    4.113109] NET: Registered protocol family 17
[    4.113442] RAS: Correctable Errors collector initialized.
[    4.113459] microcode: sig=0x906e9, pf=0x20, revision=0x5e
[    4.113600] microcode: Microcode Update Driver: v2.2.
[    4.113606] sched_clock: Marking stable (4113598422, 0)->(4113631544, -33122)
[    4.113902] registered taskstats version 1
[    4.113905] Loading compiled-in X.509 certificates
[    4.113914] zswap: loaded using pool lzo/zbud
[    4.116223] Key type big_key registered
[    4.117497]   Magic number: 2:177:292
[    4.117506] tty tty25: hash matches
[    4.117707] rtc_cmos 00:02: setting system clock to 2018-01-21 18:17:47 UTC (1516558667)
[    4.119074] Freeing unused kernel memory: 1320K
[    4.119075] Write protecting the kernel read-only data: 12288k
[    4.119455] Freeing unused kernel memory: 1524K
[    4.121123] Freeing unused kernel memory: 1308K
[    4.168756] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
[    4.169397] ACPI: Lid Switch [LID0]
[    4.169430] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[    4.169454] ACPI: Power Button [PBTN]
[    4.169475] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
[    4.169483] ACPI: Sleep Button [SBTN]
[    4.169504] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[    4.169521] ACPI: Power Button [PWRF]
[    4.173042] wmi_bus wmi_bus-PNP0C14:03: WQBC data block query control method not found
[    4.174402] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[    4.174402] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[    4.174781] i8042: Warning: Keylock active
[    4.175020] serio: i8042 KBD port at 0x60,0x64 irq 1
[    4.190295] Linux agpgart interface v0.103
[    4.191573] SCSI subsystem initialized
[    4.192039] ACPI: bus type USB registered
[    4.192051] usbcore: registered new interface driver usbfs
[    4.192055] usbcore: registered new interface driver hub
[    4.192071] usbcore: registered new device driver usb
[    4.193240] pps_core: LinuxPPS API ver. 1 registered
[    4.193241] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    4.193452] rtsx_pci 0000:04:00.0: enabling device (0000 -> 0002)
[    4.193506] PTP clock support registered
[    4.194618] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    4.194618] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    4.194832] e1000e 0000:00:1f.6: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[    4.196919] libata version 3.00 loaded.
[    4.197133] AVX2 version of gcm_enc/dec engaged.
[    4.197133] AES CTR mode by8 optimization enabled
[    4.210575] MXM: GUID detected in BIOS
[    4.210599] ACPI Warning: \_SB.PCI0.GFX0._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20170728/nsarguments-100)
[    4.210639] ACPI Warning: \_SB.PCI0.PEG1.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20170728/nsarguments-100)
[    4.210806] pci 0000:02:00.0: optimus capabilities: enabled, status dynamic power, hda bios codec supported
[    4.210808] VGA switcheroo: detected Optimus DSM method \_SB_.PCI0.PEG1.PEGP handle
[    4.210808] nouveau: detected PR support, will not use DSM
[    4.210834] nouveau 0000:02:00.0: enabling device (0006 -> 0007)
[    4.210940] checking generic (80000000 1d5000) vs hw (c0000000 10000000)
[    4.210941] checking generic (80000000 1d5000) vs hw (d0000000 2000000)
[    4.211002] nouveau 0000:02:00.0: NVIDIA GM108 (1180e0a2)
[    4.216534] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[    4.225454] nouveau 0000:02:00.0: bios: version 82.08.6e.00.01
[    4.311024] nouveau 0000:02:00.0: fb: 2048 MiB DDR3
[    4.311034] nouveau 0000:02:00.0: bus: MMIO read of 00000000 FAULT at 612004 [ IBUS ]
[    4.312428] nouveau 0000:02:00.0: bus: MMIO read of 00000000 FAULT at 10ac08 [ IBUS ]
[    4.424435] e1000e 0000:00:1f.6 0000:00:1f.6 (uninitialized): registered PHC clock
[    4.512664] e1000e 0000:00:1f.6 eth0: (PCI Express:2.5GT/s:Width x1) a4:4c:c8:6d:41:10
[    4.512668] e1000e 0000:00:1f.6 eth0: Intel(R) PRO/1000 Network Connection
[    4.512783] e1000e 0000:00:1f.6 eth0: MAC: 12, PHY: 12, PBA No: FFFFFF-0FF
[    4.513021] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    4.513025] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[    4.514399] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x00109810
[    4.514407] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[    4.514851] hub 1-0:1.0: USB hub found
[    4.514945] hub 1-0:1.0: 16 ports detected
[    4.515811] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    4.515813] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[    4.515992] hub 2-0:1.0: USB hub found
[    4.516056] hub 2-0:1.0: 10 ports detected
[    4.516314] usb: port power management may be unreliable
[    4.516975] ahci 0000:00:17.0: version 3.0
[    4.517220] ahci 0000:00:17.0: SSS flag set, parallel bus scan disabled
[    4.517307] ahci 0000:00:17.0: AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x1 impl SATA mode
[    4.517308] ahci 0000:00:17.0: flags: 64bit ncq sntf stag pm led clo only pio slum part ems deso sadm sds apst 
[    4.517582] scsi host0: ahci
[    4.518360] scsi host1: ahci
[    4.518418] ata1: SATA max UDMA/133 abar m2048@0xed353000 port 0xed353100 irq 129
[    4.518418] ata2: DUMMY
[    4.520153] [drm] Memory usable by graphics device = 4096M
[    4.520154] checking generic (80000000 1d5000) vs hw (80000000 10000000)
[    4.520155] fb: switching to inteldrmfb from EFI VGA
[    4.520164] Console: switching to colour dummy device 80x25
[    4.520342] [drm] Replacing VGA console driver
[    4.525507] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    4.525508] [drm] Driver supports precise vblank timestamp query.
[    4.526881] i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem
[    4.530074] [drm] Finished loading DMC firmware i915/kbl_dmc_ver1_01.bin (v1.1)
[    4.830793] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    4.834831] ata1.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[    4.834832] ata1.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[    4.834833] ata1.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[    4.834938] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[    4.835196] ata1.00: supports DRM functions and may not be fully accessible
[    4.835285] ata1.00: ATA-8: LITEON CV3-8D512-41 SATA 512GB SED, T89410C, max UDMA/133
[    4.835286] ata1.00: 1000215216 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
[    4.836377] ata1.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[    4.836378] ata1.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[    4.836379] ata1.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[    4.836443] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[    4.836618] ata1.00: supports DRM functions and may not be fully accessible
[    4.837101] ata1.00: configured for UDMA/133
[    4.837455] scsi 0:0:0:0: Direct-Access     ATA      LITEON CV3-8D512 10C  PQ: 0 ANSI: 5
[    4.839786] sd 0:0:0:0: [sda] 1000215216 512-byte logical blocks: (512 GB/477 GiB)
[    4.839808] sd 0:0:0:0: [sda] Write Protect is off
[    4.839809] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    4.839845] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.841652] Alternate GPT is invalid, using primary GPT.
[    4.841656]  sda: sda1 sda2
[    4.843740] sd 0:0:0:0: [sda] supports TCG Opal
[    4.843741] sd 0:0:0:0: [sda] Attached SCSI disk
[    4.846697] usb 1-1: new high-speed USB device number 2 using xhci_hcd
[    4.990715] usb-storage 1-1:1.0: USB Mass Storage device detected
[    4.991109] scsi host2: usb-storage 1-1:1.0
[    4.991179] usbcore: registered new interface driver usb-storage
[    4.991708] usbcore: registered new interface driver uas
[    5.110081] usb 1-6: new full-speed USB device number 3 using xhci_hcd
[    5.120402] clocksource: Switched to clocksource tsc
[    5.373374] usb 1-10: new full-speed USB device number 4 using xhci_hcd
[    5.376783] vga_switcheroo: enabled
[    5.376933] [TTM] Zone  kernel: Available graphics memory: 8156114 kiB
[    5.376933] [TTM] Zone   dma32: Available graphics memory: 2097152 kiB
[    5.376934] [TTM] Initializing pool allocator
[    5.376936] [TTM] Initializing DMA pool allocator
[    5.376964] nouveau 0000:02:00.0: DRM: VRAM: 2048 MiB
[    5.376964] nouveau 0000:02:00.0: DRM: GART: 1048576 MiB
[    5.376966] nouveau 0000:02:00.0: DRM: Pointer to TMDS table invalid
[    5.376969] nouveau 0000:02:00.0: DRM: DCB version 4.0
[    5.519614] nouveau 0000:02:00.0: DRM: MM: using COPY for buffer copies
[    5.519621] [drm] Initialized nouveau 1.3.1 20120801 for 0000:02:00.0 on minor 0
[    5.519976] [drm] Initialized i915 1.6.0 20170818 for 0000:00:02.0 on minor 1
[    5.521377] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[    5.522110] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input5
[    5.522147] ACPI: Video Device [PEGP] (multi-head: no  rom: yes  post: no)
[    5.522162] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:0c/LNXVIDEO:01/input/input6
[    5.548414] usb 1-10: config 0 descriptor??
[    5.690152] usb 1-11: new high-speed USB device number 5 using xhci_hcd
[    5.771078] fbcon: inteldrmfb (fb0) is primary device
[    6.012191] scsi 2:0:0:0: Direct-Access     TOSHIBA  TransMemory      1.00 PQ: 0 ANSI: 4
[    6.013073] sd 2:0:0:0: [sdb] 15148608 512-byte logical blocks: (7.76 GB/7.22 GiB)
[    6.013402] sd 2:0:0:0: [sdb] Write Protect is off
[    6.013405] sd 2:0:0:0: [sdb] Mode Sense: 45 00 00 00
[    6.013740] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    6.016122]  sdb: sdb1 sdb2
[    6.017761] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[    6.453678] [drm] RC6 on
[    7.121928] Console: switching to colour frame buffer device 240x67
[    7.148697] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[    7.229269] ISO 9660 Extensions: RRIP_1991A
[    7.241232] loop: module loaded
[    7.316609] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    7.335561] overlayfs: fs on '/run/archiso/sfs/airootfs' does not support file handles, falling back to index=off.
[    8.247204] ip_tables: (C) 2000-2006 Netfilter Core Team
[    8.277460] systemd[1]: systemd 236 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN default-hierarchy=hybrid)
[    8.277567] systemd[1]: Detected architecture x86-64.
[    8.288254] systemd[1]: Set hostname to <archiso>.
[    8.313557] systemd[1]: Initializing machine ID from random generator.
[    8.575412] systemd[1]: Unnecessary job for /dev/loop0 was removed.
[    8.575539] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    8.575757] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    8.576112] systemd[1]: Created slice User and Session Slice.
[    8.576201] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[    8.576272] systemd[1]: Reached target Paths.
[    8.581591] random: crng init done
[    8.701647] systemd-journald[253]: Received request to flush runtime journal from PID 1
[    8.863307] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    8.877981] intel-lpss 0000:00:15.0: enabling device (0000 -> 0002)
[    8.948185] idma64 idma64.0: Found Intel integrated DMA 64-bit
[    8.948587] ACPI: AC Adapter [AC] (off-line)
[    8.977344] intel-lpss 0000:00:15.1: enabling device (0000 -> 0002)
[    8.977521] idma64 idma64.1: Found Intel integrated DMA 64-bit
[    8.987658] (NULL device *): hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
[    8.987737] mei_me 0000:00:16.0: enabling device (0000 -> 0002)
[    9.004163] proc_thermal 0000:00:04.0: enabling device (0000 -> 0002)
[    9.004216] tpm_tis MSFT0101:00: 2.0 TPM (device-id 0xFE, rev-id 4)
[    9.014640] int3403 thermal: probe of INT3403:03 failed with error -22
[    9.045897] (NULL device *): hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
[    9.048578] thermal LNXTHERM:00: registered as thermal_zone6
[    9.048579] ACPI: Thermal Zone [THM] (25 C)
[    9.065553] ACPI: Battery Slot [BAT0] (battery present)
[    9.077021] hidraw: raw HID events driver (C) Jiri Kosina
[    9.108326] i801_smbus 0000:00:1f.4: SPD Write Disable is set
[    9.108352] i801_smbus 0000:00:1f.4: SMBus using PCI interrupt
[    9.109043] e1000e 0000:00:1f.6 enp0s31f6: renamed from eth0
[    9.135011] Bluetooth: Core ver 2.22
[    9.135020] NET: Registered protocol family 31
[    9.135021] Bluetooth: HCI device and connection manager initialized
[    9.135023] Bluetooth: HCI socket layer initialized
[    9.135025] Bluetooth: L2CAP socket layer initialized
[    9.135027] Bluetooth: SCO socket layer initialized
[    9.175733] media: Linux media interface: v0.10
[    9.195095] Linux video capture interface: v2.00
[    9.216853] usbcore: registered new interface driver btusb
[    9.221729] Bluetooth: HCI UART driver ver 2.3
[    9.221731] Bluetooth: HCI UART protocol H4 registered
[    9.221732] Bluetooth: HCI UART protocol BCSP registered
[    9.221735] Bluetooth: hci0: Bootloader revision 0.0 build 26 week 38 2015
[    9.221751] Bluetooth: HCI UART protocol LL registered
[    9.221752] Bluetooth: HCI UART protocol ATH3K registered
[    9.221753] Bluetooth: HCI UART protocol Three-wire (H5) registered
[    9.221783] Bluetooth: HCI UART protocol Intel registered
[    9.221807] Bluetooth: HCI UART protocol Broadcom registered
[    9.221808] Bluetooth: HCI UART protocol QCA registered
[    9.221809] Bluetooth: HCI UART protocol AG6XX registered
[    9.221809] Bluetooth: HCI UART protocol Marvell registered
[    9.224217] Bluetooth: hci0: Device revision is 16
[    9.224218] Bluetooth: hci0: Secure boot is enabled
[    9.224219] Bluetooth: hci0: OTP lock is enabled
[    9.224220] Bluetooth: hci0: API lock is enabled
[    9.224221] Bluetooth: hci0: Debug lock is disabled
[    9.224222] Bluetooth: hci0: Minimum firmware build 1 week 10 2014
[    9.225883] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[    9.239276] dell-wmi 9DBB5994-A997-11DA-B012-B622A1EF5492: Detected Dell WMI interface version 1
[    9.239335] input: Dell WMI hotkeys as /devices/platform/PNP0C14:03/wmi_bus/wmi_bus-PNP0C14:03/9DBB5994-A997-11DA-B012-B622A1EF5492/input/input7
[    9.244600] Intel(R) Wireless WiFi driver for Linux
[    9.244601] Copyright(c) 2003- 2015 Intel Corporation
[    9.244962] iwlwifi 0000:03:00.0: enabling device (0000 -> 0002)
[    9.246609] uvcvideo: Found UVC 1.00 device Integrated_Webcam_HD (0c45:6717)
[    9.251057] uvcvideo 1-11:1.0: Entity type for entity Extension 4 was not initialized!
[    9.251058] uvcvideo 1-11:1.0: Entity type for entity Extension 3 was not initialized!
[    9.251059] uvcvideo 1-11:1.0: Entity type for entity Processing 2 was not initialized!
[    9.251060] uvcvideo 1-11:1.0: Entity type for entity Camera 1 was not initialized!
[    9.251187] input: Integrated_Webcam_HD: Integrate as /devices/pci0000:00/0000:00:14.0/usb1/1-11/1-11:1.0/input/input8
[    9.251287] usbcore: registered new interface driver uvcvideo
[    9.251288] USB Video Class driver (1.1.1)
[    9.270232] RAPL PMU: API unit is 2^-32 Joules, 5 fixed counters, 655360 ms ovfl timer
[    9.270233] RAPL PMU: hw unit of domain pp0-core 2^-14 Joules
[    9.270234] RAPL PMU: hw unit of domain package 2^-14 Joules
[    9.270234] RAPL PMU: hw unit of domain dram 2^-14 Joules
[    9.270234] RAPL PMU: hw unit of domain pp1-gpu 2^-14 Joules
[    9.270235] RAPL PMU: hw unit of domain psys 2^-14 Joules
[    9.302379] snd_hda_intel 0000:00:1f.3: enabling device (0000 -> 0002)
[    9.302530] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
[    9.603861] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC3246: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[    9.603865] snd_hda_codec_realtek hdaudioC0D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[    9.603868] snd_hda_codec_realtek hdaudioC0D0:    hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
[    9.603871] snd_hda_codec_realtek hdaudioC0D0:    mono: mono_out=0x0
[    9.603873] snd_hda_codec_realtek hdaudioC0D0:    inputs:
[    9.603876] snd_hda_codec_realtek hdaudioC0D0:      Headset Mic=0x19
[    9.603879] snd_hda_codec_realtek hdaudioC0D0:      Headphone Mic=0x1a
[    9.603881] snd_hda_codec_realtek hdaudioC0D0:      Internal Mic=0x12
[    9.648163] Bluetooth: hci0: Found device firmware: intel/ibt-12-16.sfi
[    9.652162] iTCO_vendor_support: vendor-support=0
[    9.655149] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[    9.655335] iTCO_wdt: Found a Intel PCH TCO device (Version=4, TCOBASE=0x0400)
[    9.659269] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[    9.660798] dell_laptop: Using i8042 filter function for receiving events
[    9.739324] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1f.3/sound/card0/input9
[    9.739539] input: HDA Intel PCH Headphone Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input11
[    9.739576] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input13
[    9.739612] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input14
[    9.739654] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input15
[    9.739688] input: HDA Intel PCH HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input16
[    9.739723] input: HDA Intel PCH HDMI/DP,pcm=10 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input17
[    9.742130] input: DualPoint Stick as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-10/i2c-DLL07D0:01/0018:044E:120B.0001/input/input12
[    9.742177] input: DLL07D0:01 044E:120B as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-10/i2c-DLL07D0:01/0018:044E:120B.0001/input/input10
[    9.742223] hid-alps 0018:044E:120B.0001: input,hidraw0: I2C HID v1.00 Mouse [DLL07D0:01 044E:120B] on i2c-DLL07D0:01
[    9.758258] iwlwifi 0000:03:00.0: loaded firmware version 34.0.1 op_mode iwlmvm
[    9.795993] mousedev: PS/2 mouse device common for all mice
[    9.813900] intel_rapl: Found RAPL domain package
[    9.813902] intel_rapl: Found RAPL domain core
[    9.813902] intel_rapl: Found RAPL domain uncore
[    9.813903] intel_rapl: Found RAPL domain dram
[    9.847253] iwlwifi 0000:03:00.0: Detected Intel(R) Dual Band Wireless AC 8265, REV=0x230
[    9.879898] input: Intel HID events as /devices/platform/INT33D5:00/input/input18
[    9.880082] intel-hid INT33D5:00: platform supports 5 button array
[    9.880106] input: Intel HID 5 button array as /devices/platform/INT33D5:00/input/input19
[    9.880347] input: PC Speaker as /devices/platform/pcspkr/input/input20
[    9.910853] iwlwifi 0000:03:00.0: base HW address: d4:25:8b:b9:24:31
[    9.999061] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs'
[    9.999525] (NULL device *): hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
[    9.999553] thermal thermal_zone8: failed to read out thermal zone (-61)
[   10.010686] iwlwifi 0000:03:00.0 wlp3s0: renamed from wlan0
[   11.238175] Bluetooth: hci0: Waiting for firmware download to complete
[   11.238742] Bluetooth: hci0: Firmware loaded in 1974180 usecs
[   11.238794] Bluetooth: hci0: Waiting for device to boot
[   11.250752] Bluetooth: hci0: Device booted in 11714 usecs
[   11.264134] Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-12-16.ddc
[   11.265804] Bluetooth: hci0: Applying Intel DDC parameters completed
[   11.640367] IPv6: ADDRCONF(NETDEV_UP): enp0s31f6: link is not ready
[   14.849637] e1000e: enp0s31f6 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
[   14.849711] IPv6: ADDRCONF(NETDEV_CHANGE): enp0s31f6: link becomes ready
[  145.603350] Alternate GPT is invalid, using primary GPT.
[  145.603355]  sda: sda1 sda2
[  169.897342] Alternate GPT is invalid, using primary GPT.
[  169.897356]  sda: sda1 sda2
[  188.313657] ata1: log page 10h reported inactive tag 0
[  188.315818] ata1.00: exception Emask 0x1 SAct 0x2 SErr 0x0 action 0x0
[  188.318003] ata1.00: irq_stat 0x40000008
[  188.319098] ata1.00: failed command: WRITE FPDMA QUEUED
[  188.319624] ata1.00: cmd 61/08:08:f8:ff:03/00:00:00:00:00/40 tag 1 ncq dma 4096 out
                        res 40/00:0c:f8:ff:03/00:00:00:00:00/40 Emask 0x1 (device error)
[  188.320716] ata1.00: status: { DRDY }
[  188.321648] ata1.00: supports DRM functions and may not be fully accessible
[  188.322229] ata1.00: supports DRM functions and may not be fully accessible
[  188.322615] ata1.00: configured for UDMA/133
[  188.322621] ata1: EH complete
[  188.322803] ata1: log page 10h reported inactive tag 0
[  188.323380] ata1.00: exception Emask 0x1 SAct 0x10 SErr 0x0 action 0x0
[  188.323968] ata1.00: irq_stat 0x40000008
[  188.324535] ata1.00: failed command: WRITE FPDMA QUEUED
[  188.325090] ata1.00: cmd 61/08:20:f8:ff:03/00:00:00:00:00/40 tag 4 ncq dma 4096 out
                        res 40/00:24:f8:ff:03/00:00:00:00:00/40 Emask 0x1 (device error)
[  188.326238] ata1.00: status: { DRDY }
[  188.327013] ata1.00: supports DRM functions and may not be fully accessible
[  188.327589] ata1.00: supports DRM functions and may not be fully accessible
[  188.327973] ata1.00: configured for UDMA/133
[  188.327976] ata1: EH complete
[  188.328098] ata1: log page 10h reported inactive tag 0
[  188.328674] ata1.00: exception Emask 0x1 SAct 0x100000 SErr 0x0 action 0x0
[  188.329275] ata1.00: irq_stat 0x40000008
[  188.329850] ata1.00: failed command: WRITE FPDMA QUEUED
[  188.330473] ata1.00: cmd 61/08:a0:f8:ff:03/00:00:00:00:00/40 tag 20 ncq dma 4096 out
                        res 40/00:a4:f8:ff:03/00:00:00:00:00/40 Emask 0x1 (device error)
[  188.331707] ata1.00: status: { DRDY }
[  188.332482] ata1.00: supports DRM functions and may not be fully accessible
[  188.333043] ata1.00: supports DRM functions and may not be fully accessible
[  188.333430] ata1.00: configured for UDMA/133
[  188.333433] ata1: EH complete
[  188.333562] ata1: log page 10h reported inactive tag 0
[  188.334155] ata1.00: NCQ disabled due to excessive errors
[  188.334156] ata1.00: exception Emask 0x1 SAct 0x8 SErr 0x0 action 0x0
[  188.334771] ata1.00: irq_stat 0x40000008
[  188.335362] ata1.00: failed command: WRITE FPDMA QUEUED
[  188.335965] ata1.00: cmd 61/08:18:f8:ff:03/00:00:00:00:00/40 tag 3 ncq dma 4096 out
                        res 40/00:1c:f8:ff:03/00:00:00:00:00/40 Emask 0x1 (device error)
[  188.337196] ata1.00: status: { DRDY }
[  188.338045] ata1.00: supports DRM functions and may not be fully accessible
[  188.338614] ata1.00: supports DRM functions and may not be fully accessible
[  188.339002] ata1.00: configured for UDMA/133
[  188.339004] ata1: EH complete
[  188.339053] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[  188.339657] ata1.00: irq_stat 0x40000001
[  188.340287] ata1.00: failed command: WRITE DMA
[  188.340947] ata1.00: cmd ca/00:08:f8:ff:03/00:00:00:00:00/e0 tag 22 dma 4096 out
                        res 51/04:08:f8:ff:03/00:00:00:00:00/e0 Emask 0x1 (device error)
[  188.342210] ata1.00: status: { DRDY ERR }
[  188.342837] ata1.00: error: { ABRT }
[  188.343669] ata1.00: supports DRM functions and may not be fully accessible
[  188.344246] ata1.00: supports DRM functions and may not be fully accessible
[  188.344629] ata1.00: configured for UDMA/133
[  188.344632] ata1: EH complete
[  188.344681] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[  188.345335] ata1.00: irq_stat 0x40000001
[  188.345967] ata1.00: failed command: WRITE DMA
[  188.346623] ata1.00: cmd ca/00:08:f8:ff:03/00:00:00:00:00/e0 tag 15 dma 4096 out
                        res 51/04:08:f8:ff:03/00:00:00:00:00/e0 Emask 0x1 (device error)
[  188.347960] ata1.00: status: { DRDY ERR }
[  188.348654] ata1.00: error: { ABRT }
[  188.349454] ata1.00: supports DRM functions and may not be fully accessible
[  188.350030] ata1.00: supports DRM functions and may not be fully accessible
[  188.350411] ata1.00: configured for UDMA/133
[  188.350414] sd 0:0:0:0: [sda] tag#15 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08
[  188.350415] sd 0:0:0:0: [sda] tag#15 Sense Key : 0x5 [current] 
[  188.350416] sd 0:0:0:0: [sda] tag#15 ASC=0x21 ASCQ=0x4 
[  188.350417] sd 0:0:0:0: [sda] tag#15 CDB: opcode=0x2a 2a 00 00 03 ff f8 00 00 08 00
[  188.350418] print_req_error: I/O error, dev sda, sector 262136
[  188.351078] Buffer I/O error on dev sda, logical block 32767, lost async page write
[  188.351730] ata1: EH complete
[  188.370126] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[  188.372796] ata1.00: irq_stat 0x40000001
[  188.375474] ata1.00: failed command: WRITE DMA
[  188.376346] ata1.00: cmd ca/00:18:00:00:00/00:00:00:00:00/e0 tag 22 dma 12288 out
                        res 51/04:18:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[  188.377714] ata1.00: status: { DRDY ERR }
[  188.378408] ata1.00: error: { ABRT }
[  188.379248] ata1.00: supports DRM functions and may not be fully accessible
[  188.379818] ata1.00: supports DRM functions and may not be fully accessible
[  188.380253] ata1.00: configured for UDMA/133
[  188.380257] ata1: EH complete
[  188.380312] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[  188.380996] ata1.00: irq_stat 0x40000001
[  188.381713] ata1.00: failed command: WRITE DMA
[  188.382412] ata1.00: cmd ca/00:18:00:00:00/00:00:00:00:00/e0 tag 25 dma 12288 out
                        res 51/04:18:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[  188.383867] ata1.00: status: { DRDY ERR }
[  188.384571] ata1.00: error: { ABRT }
[  188.385451] ata1.00: supports DRM functions and may not be fully accessible
[  188.386038] ata1.00: supports DRM functions and may not be fully accessible
[  188.386425] ata1.00: configured for UDMA/133
[  188.386427] ata1: EH complete
[  188.386477] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[  188.387214] ata1.00: irq_stat 0x40000001
[  188.387926] ata1.00: failed command: WRITE DMA
[  188.388652] ata1.00: cmd ca/00:18:00:00:00/00:00:00:00:00/e0 tag 29 dma 12288 out
                        res 51/04:18:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[  188.390086] ata1.00: status: { DRDY ERR }
[  188.390802] ata1.00: error: { ABRT }
[  188.391652] ata1.00: supports DRM functions and may not be fully accessible
[  188.392227] ata1.00: supports DRM functions and may not be fully accessible
[  188.392616] ata1.00: configured for UDMA/133
[  188.392618] ata1: EH complete
[  188.392667] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[  188.393324] ata1.00: irq_stat 0x40000001
[  188.393990] ata1.00: failed command: WRITE DMA
[  188.394635] ata1.00: cmd ca/00:18:00:00:00/00:00:00:00:00/e0 tag 2 dma 12288 out
                        res 51/04:18:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[  188.395975] ata1.00: status: { DRDY ERR }
[  188.396622] ata1.00: error: { ABRT }
[  188.397448] ata1.00: supports DRM functions and may not be fully accessible
[  188.398018] ata1.00: supports DRM functions and may not be fully accessible
[  188.398405] ata1.00: configured for UDMA/133
[  188.398407] ata1: EH complete
[  188.398457] ata1: limiting SATA link speed to 3.0 Gbps
[  188.398458] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
[  188.399121] ata1.00: irq_stat 0x40000001
[  188.399761] ata1.00: failed command: WRITE DMA
[  188.400419] ata1.00: cmd ca/00:18:00:00:00/00:00:00:00:00/e0 tag 6 dma 12288 out
                        res 51/04:18:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[  188.401725] ata1.00: status: { DRDY ERR }
[  188.402384] ata1.00: error: { ABRT }
[  188.403019] ata1: hard resetting link
[  188.717975] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[  188.723620] ata1.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[  188.723625] ata1.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[  188.723629] ata1.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[  188.723727] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[  188.723907] ata1.00: supports DRM functions and may not be fully accessible
[  188.726442] ata1.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[  188.726446] ata1.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[  188.726450] ata1.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[  188.726516] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[  188.726822] ata1.00: supports DRM functions and may not be fully accessible
[  188.727393] ata1.00: configured for UDMA/133
[  188.727444] ata1: EH complete
[  188.727528] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[  188.730127] ata1.00: irq_stat 0x40000001
[  188.732533] ata1.00: failed command: WRITE DMA
[  188.734941] ata1.00: cmd ca/00:18:00:00:00/00:00:00:00:00/e0 tag 10 dma 12288 out
                        res 51/04:18:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[  188.739774] ata1.00: status: { DRDY ERR }
[  188.742192] ata1.00: error: { ABRT }
[  188.744769] ata1.00: supports DRM functions and may not be fully accessible
[  188.745406] ata1.00: supports DRM functions and may not be fully accessible
[  188.745825] ata1.00: configured for UDMA/133
[  188.745839] sd 0:0:0:0: [sda] tag#10 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08
[  188.745843] sd 0:0:0:0: [sda] tag#10 Sense Key : 0x5 [current] 
[  188.745846] sd 0:0:0:0: [sda] tag#10 ASC=0x21 ASCQ=0x4 
[  188.745849] sd 0:0:0:0: [sda] tag#10 CDB: opcode=0x2a 2a 00 00 00 00 00 00 00 18 00
[  188.745852] print_req_error: I/O error, dev sda, sector 0
[  188.748241] Buffer I/O error on dev sda, logical block 0, lost async page write
[  188.750676] Buffer I/O error on dev sda, logical block 1, lost async page write
[  188.753064] Buffer I/O error on dev sda, logical block 2, lost async page write
[  188.755438] ata1: EH complete
[  188.766809] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[  188.769198] ata1.00: irq_stat 0x40000001
[  188.771552] ata1.00: failed command: WRITE DMA EXT
[  188.773907] ata1.00: cmd 35/00:18:98:12:9e/00:00:3b:00:00/e0 tag 16 dma 12288 out
                        res 51/04:18:98:12:9e/00:00:3b:00:00/e0 Emask 0x1 (device error)
[  188.778603] ata1.00: status: { DRDY ERR }
[  188.780885] ata1.00: error: { ABRT }
[  188.782712] ata1.00: supports DRM functions and may not be fully accessible
[  188.783344] ata1.00: supports DRM functions and may not be fully accessible
[  188.783763] ata1.00: configured for UDMA/133
[  188.783777] ata1: EH complete
[  188.783855] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[  188.785495] ata1.00: irq_stat 0x40000001
[  188.786801] ata1.00: failed command: WRITE DMA EXT
[  188.788043] ata1.00: cmd 35/00:18:98:12:9e/00:00:3b:00:00/e0 tag 19 dma 12288 out
                        res 51/04:18:98:12:9e/00:00:3b:00:00/e0 Emask 0x1 (device error)
[  188.790561] ata1.00: status: { DRDY ERR }
[  188.791610] ata1.00: error: { ABRT }
[  188.792779] ata1.00: supports DRM functions and may not be fully accessible
[  188.793365] ata1.00: supports DRM functions and may not be fully accessible
[  188.793763] ata1.00: configured for UDMA/133
[  188.793768] ata1: EH complete
[  188.793830] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[  188.794849] ata1.00: irq_stat 0x40000001
[  188.795860] ata1.00: failed command: WRITE DMA EXT
[  188.796706] ata1.00: cmd 35/00:18:98:12:9e/00:00:3b:00:00/e0 tag 23 dma 12288 out
                        res 51/04:18:98:12:9e/00:00:3b:00:00/e0 Emask 0x1 (device error)
[  188.798444] ata1.00: status: { DRDY ERR }
[  188.799301] ata1.00: error: { ABRT }
[  188.800301] ata1.00: supports DRM functions and may not be fully accessible
[  188.800887] ata1.00: supports DRM functions and may not be fully accessible
[  188.801277] ata1.00: configured for UDMA/133
[  188.801280] ata1: EH complete
[  188.801332] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[  188.802060] ata1.00: irq_stat 0x40000001
[  188.802807] ata1.00: failed command: WRITE DMA EXT
[  188.803555] ata1.00: cmd 35/00:18:98:12:9e/00:00:3b:00:00/e0 tag 27 dma 12288 out
                        res 51/04:18:98:12:9e/00:00:3b:00:00/e0 Emask 0x1 (device error)
[  188.805027] ata1.00: status: { DRDY ERR }
[  188.805779] ata1.00: error: { ABRT }
[  188.806576] ata1.00: supports DRM functions and may not be fully accessible
[  188.807147] ata1.00: supports DRM functions and may not be fully accessible
[  188.807539] ata1.00: configured for UDMA/133
[  188.807542] ata1: EH complete
[  188.807593] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[  188.808260] ata1.00: irq_stat 0x40000001
[  188.808903] ata1.00: failed command: WRITE DMA EXT
[  188.809560] ata1.00: cmd 35/00:18:98:12:9e/00:00:3b:00:00/e0 tag 0 dma 12288 out
                        res 51/04:18:98:12:9e/00:00:3b:00:00/e0 Emask 0x1 (device error)
[  188.810865] ata1.00: status: { DRDY ERR }
[  188.811499] ata1.00: error: { ABRT }
[  188.812246] ata1.00: supports DRM functions and may not be fully accessible
[  188.812823] ata1.00: supports DRM functions and may not be fully accessible
[  188.813213] ata1.00: configured for UDMA/133
[  188.813215] ata1: EH complete
[  188.813266] ata1: limiting SATA link speed to 1.5 Gbps
[  188.813267] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
[  188.813871] ata1.00: irq_stat 0x40000001
[  188.814485] ata1.00: failed command: WRITE DMA EXT
[  188.815075] ata1.00: cmd 35/00:18:98:12:9e/00:00:3b:00:00/e0 tag 4 dma 12288 out
                        res 51/04:18:98:12:9e/00:00:3b:00:00/e0 Emask 0x1 (device error)
[  188.816253] ata1.00: status: { DRDY ERR }
[  188.816844] ata1.00: error: { ABRT }
[  188.817443] ata1: hard resetting link
[  189.130907] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[  189.136312] ata1.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[  189.136317] ata1.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[  189.136321] ata1.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[  189.136387] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[  189.136566] ata1.00: supports DRM functions and may not be fully accessible
[  189.138976] ata1.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[  189.138981] ata1.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[  189.138984] ata1.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[  189.139057] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[  189.139233] ata1.00: supports DRM functions and may not be fully accessible
[  189.139668] ata1.00: configured for UDMA/133
[  189.139698] sd 0:0:0:0: [sda] tag#4 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08
[  189.139702] sd 0:0:0:0: [sda] tag#4 Sense Key : 0x5 [current] 
[  189.139706] sd 0:0:0:0: [sda] tag#4 ASC=0x21 ASCQ=0x4 
[  189.139709] sd 0:0:0:0: [sda] tag#4 CDB: opcode=0x2a 2a 00 3b 9e 12 98 00 00 18 00
[  189.139712] print_req_error: I/O error, dev sda, sector 1000215192
[  189.142074] Buffer I/O error on dev sda, logical block 125026899, lost async page write
[  189.144480] Buffer I/O error on dev sda, logical block 125026900, lost async page write
[  189.145243] Buffer I/O error on dev sda, logical block 125026901, lost async page write
[  189.145866] ata1: EH complete
[  189.166800] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[  189.169134] ata1.00: irq_stat 0x40000001
[  189.171478] ata1.00: failed command: WRITE DMA
[  189.173779] ata1.00: cmd ca/00:28:00:00:00/00:00:00:00:00/e0 tag 17 dma 20480 out
                        res 51/04:28:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[  189.178432] ata1.00: status: { DRDY ERR }
[  189.180761] ata1.00: error: { ABRT }
[  189.183269] ata1.00: supports DRM functions and may not be fully accessible
[  189.184022] ata1.00: supports DRM functions and may not be fully accessible
[  189.184494] ata1.00: configured for UDMA/133
[  189.184512] ata1: EH complete
[  189.184596] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[  189.186934] ata1.00: irq_stat 0x40000001
[  189.189244] ata1.00: failed command: WRITE DMA
[  189.190254] ata1.00: cmd ca/00:28:00:00:00/00:00:00:00:00/e0 tag 20 dma 20480 out
                        res 51/04:28:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[  189.191459] ata1.00: status: { DRDY ERR }
[  189.192044] ata1.00: error: { ABRT }
[  189.192775] ata1.00: supports DRM functions and may not be fully accessible
[  189.193368] ata1.00: supports DRM functions and may not be fully accessible
[  189.193765] ata1.00: configured for UDMA/133
[  189.193768] ata1: EH complete
[  189.193819] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[  189.194399] ata1.00: irq_stat 0x40000001
[  189.194981] ata1.00: failed command: WRITE DMA
[  189.195547] ata1.00: cmd ca/00:28:00:00:00/00:00:00:00:00/e0 tag 26 dma 20480 out
                        res 51/04:28:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[  189.196753] ata1.00: status: { DRDY ERR }
[  189.197416] ata1.00: error: { ABRT }
[  189.198151] ata1.00: supports DRM functions and may not be fully accessible
[  189.198735] ata1.00: supports DRM functions and may not be fully accessible
[  189.199128] ata1.00: configured for UDMA/133
[  189.199130] ata1: EH complete
[  189.199179] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[  189.199784] ata1.00: irq_stat 0x40000001
[  189.200420] ata1.00: failed command: WRITE DMA
[  189.201058] ata1.00: cmd ca/00:28:00:00:00/00:00:00:00:00/e0 tag 30 dma 20480 out
                        res 51/04:28:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[  189.202224] ata1.00: status: { DRDY ERR }
[  189.202813] ata1.00: error: { ABRT }
[  189.203565] ata1.00: supports DRM functions and may not be fully accessible
[  189.204158] ata1.00: supports DRM functions and may not be fully accessible
[  189.204554] ata1.00: configured for UDMA/133
[  189.204556] ata1: EH complete
[  189.204606] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[  189.205199] ata1.00: irq_stat 0x40000001
[  189.205768] ata1.00: failed command: WRITE DMA
[  189.206355] ata1.00: cmd ca/00:28:00:00:00/00:00:00:00:00/e0 tag 5 dma 20480 out
                        res 51/04:28:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[  189.207553] ata1.00: status: { DRDY ERR }
[  189.208181] ata1.00: error: { ABRT }
[  189.208914] ata1.00: supports DRM functions and may not be fully accessible
[  189.209499] ata1.00: supports DRM functions and may not be fully accessible
[  189.209892] ata1.00: configured for UDMA/133
[  189.209894] ata1: EH complete
[  189.209943] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[  189.210525] ata1.00: irq_stat 0x40000001
[  189.211179] ata1.00: failed command: WRITE DMA
[  189.211807] ata1.00: cmd ca/00:28:00:00:00/00:00:00:00:00/e0 tag 9 dma 20480 out
                        res 51/04:28:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[  189.212967] ata1.00: status: { DRDY ERR }
[  189.213557] ata1.00: error: { ABRT }
[  189.214326] ata1.00: supports DRM functions and may not be fully accessible
[  189.214913] ata1.00: supports DRM functions and may not be fully accessible
[  189.215307] ata1.00: configured for UDMA/133
[  189.215310] sd 0:0:0:0: [sda] tag#9 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08
[  189.215311] sd 0:0:0:0: [sda] tag#9 Sense Key : 0x5 [current] 
[  189.215312] sd 0:0:0:0: [sda] tag#9 ASC=0x21 ASCQ=0x4 
[  189.215312] sd 0:0:0:0: [sda] tag#9 CDB: opcode=0x2a 2a 00 00 00 00 00 00 00 28 00
[  189.215313] print_req_error: I/O error, dev sda, sector 0
[  189.215900] Buffer I/O error on dev sda, logical block 0, lost async page write
[  189.216479] Buffer I/O error on dev sda, logical block 1, lost async page write
[  189.217314] Buffer I/O error on dev sda, logical block 2, lost async page write
[  189.218005] ata1: EH complete
[  189.230040] ata1.00: limiting speed to UDMA/100:PIO4
[  189.230042] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
[  189.230654] ata1.00: irq_stat 0x40000001
[  189.231252] ata1.00: failed command: WRITE DMA EXT
[  189.231862] ata1.00: cmd 35/00:28:88:12:9e/00:00:3b:00:00/e0 tag 15 dma 20480 out
                        res 51/04:28:88:12:9e/00:00:3b:00:00/e0 Emask 0x1 (device error)
[  189.233052] ata1.00: status: { DRDY ERR }
[  189.233699] ata1.00: error: { ABRT }
[  189.234340] ata1: hard resetting link
[  189.544270] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[  189.549957] ata1.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[  189.549964] ata1.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[  189.549993] ata1.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[  189.550129] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[  189.550397] ata1.00: supports DRM functions and may not be fully accessible
[  189.553290] ata1.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[  189.553295] ata1.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[  189.553320] ata1.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[  189.553390] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[  189.553605] ata1.00: supports DRM functions and may not be fully accessible
[  189.554153] ata1.00: configured for UDMA/100
[  189.554200] ata1: EH complete
[  189.554296] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[  189.556917] ata1.00: irq_stat 0x40000001
[  189.559474] ata1.00: failed command: WRITE DMA EXT
[  189.562039] ata1.00: cmd 35/00:28:88:12:9e/00:00:3b:00:00/e0 tag 20 dma 20480 out
                        res 51/04:28:88:12:9e/00:00:3b:00:00/e0 Emask 0x1 (device error)
[  189.566853] ata1.00: status: { DRDY ERR }
[  189.569136] ata1.00: error: { ABRT }
[  189.571624] ata1.00: supports DRM functions and may not be fully accessible
[  189.572282] ata1.00: supports DRM functions and may not be fully accessible
[  189.572714] ata1.00: configured for UDMA/100
[  189.572724] ata1: EH complete
[  189.572821] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[  189.575137] ata1.00: irq_stat 0x40000001
[  189.577438] ata1.00: failed command: WRITE DMA EXT
[  189.579713] ata1.00: cmd 35/00:28:88:12:9e/00:00:3b:00:00/e0 tag 28 dma 20480 out
                        res 51/04:28:88:12:9e/00:00:3b:00:00/e0 Emask 0x1 (device error)
[  189.584319] ata1.00: status: { DRDY ERR }
[  189.586379] ata1.00: error: { ABRT }
[  189.588155] ata1.00: supports DRM functions and may not be fully accessible
[  189.588789] ata1.00: supports DRM functions and may not be fully accessible
[  189.589204] ata1.00: configured for UDMA/100
[  189.589211] ata1: EH complete
[  189.589286] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[  189.590881] ata1.00: irq_stat 0x40000001
[  189.592115] ata1.00: failed command: WRITE DMA EXT
[  189.593351] ata1.00: cmd 35/00:28:88:12:9e/00:00:3b:00:00/e0 tag 8 dma 20480 out
                        res 51/04:28:88:12:9e/00:00:3b:00:00/e0 Emask 0x1 (device error)
[  189.595802] ata1.00: status: { DRDY ERR }
[  189.596811] ata1.00: error: { ABRT }
[  189.597983] ata1.00: supports DRM functions and may not be fully accessible
[  189.598585] ata1.00: supports DRM functions and may not be fully accessible
[  189.598991] ata1.00: configured for UDMA/100
[  189.598995] ata1: EH complete
[  189.599053] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[  189.600067] ata1.00: irq_stat 0x40000001
[  189.601025] ata1.00: failed command: WRITE DMA EXT
[  189.601875] ata1.00: cmd 35/00:28:88:12:9e/00:00:3b:00:00/e0 tag 21 dma 20480 out
                        res 51/04:28:88:12:9e/00:00:3b:00:00/e0 Emask 0x1 (device error)
[  189.603572] ata1.00: status: { DRDY ERR }
[  189.604431] ata1.00: error: { ABRT }
[  189.605449] ata1.00: supports DRM functions and may not be fully accessible
[  189.606043] ata1.00: supports DRM functions and may not be fully accessible
[  189.606442] ata1.00: configured for UDMA/100
[  189.606445] ata1: EH complete
[  189.606498] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[  189.607250] ata1.00: irq_stat 0x40000001
[  189.607978] ata1.00: failed command: WRITE DMA EXT
[  189.608724] ata1.00: cmd 35/00:28:88:12:9e/00:00:3b:00:00/e0 tag 7 dma 20480 out
                        res 51/04:28:88:12:9e/00:00:3b:00:00/e0 Emask 0x1 (device error)
[  189.610208] ata1.00: status: { DRDY ERR }
[  189.610939] ata1.00: error: { ABRT }
[  189.611770] ata1.00: supports DRM functions and may not be fully accessible
[  189.612353] ata1.00: supports DRM functions and may not be fully accessible
[  189.612748] ata1.00: configured for UDMA/100
[  189.612752] sd 0:0:0:0: [sda] tag#7 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08
[  189.612753] sd 0:0:0:0: [sda] tag#7 Sense Key : 0x5 [current] 
[  189.612754] sd 0:0:0:0: [sda] tag#7 ASC=0x21 ASCQ=0x4 
[  189.612755] sd 0:0:0:0: [sda] tag#7 CDB: opcode=0x2a 2a 00 3b 9e 12 88 00 00 28 00
[  189.612756] print_req_error: I/O error, dev sda, sector 1000215176
[  189.613420] ata1: EH complete
[  202.820753] Alternate GPT is invalid, using primary GPT.
[  202.820770]  sda: sda1 sda2

all I did was `parted` then `print`. I got warning that primary is ok but secondary table is corrupted. I was asked if the GPT should be fixed, then errors happened.

Head_on_a_Stick · 2018-01-21 18:46:20

Searches for the error messages seem to show hardware-related problems — could the cable/connector be damaged?

I've never dealt with firmware-encrypted drives (if that is what we are dealing with here) but does this help: https://wiki.archlinux.org/index.php/Se … ing_Drives

This bit from `dmesg` looks relevant (perhaps):

[    4.843740] sd 0:0:0:0: [sda] supports TCG Opal

R00KIE · 2018-01-21 19:06:36

The line Head_on_a_Stick mentions probably explains why you can't write to the SSD and why you only see two small partitions.

Install sedutil[1] from the aur and post the output of 'sedutil-cli --query /dev/sda'.

[1] https://aur.archlinux.org/packages/sedutil

Edit:
You may have to boot with libata.allow_tpm=1 in order to let sedutil communicate with the SSD.

Last edited by R00KIE (2018-01-21 19:08:43)

crazySocket · 2018-01-24 11:05:41

I've found out the disc is indeed self-encrypted. Without the proper key I cannot do anything. Thanks for help.

Arch Linux

#1 2018-01-20 23:13:15

[solved] cannot clear the disk in UEFI install

#2 2018-01-20 23:35:39

Re: [solved] cannot clear the disk in UEFI install

#3 2018-01-20 23:41:04

Re: [solved] cannot clear the disk in UEFI install

#4 2018-01-21 01:16:45

Re: [solved] cannot clear the disk in UEFI install

#5 2018-01-21 10:38:46

Re: [solved] cannot clear the disk in UEFI install

#6 2018-01-21 11:40:46

Re: [solved] cannot clear the disk in UEFI install

#7 2018-01-21 12:12:54

Re: [solved] cannot clear the disk in UEFI install

#8 2018-01-21 12:21:16

Re: [solved] cannot clear the disk in UEFI install

#9 2018-01-21 18:30:09

Re: [solved] cannot clear the disk in UEFI install

#10 2018-01-21 18:46:20

Re: [solved] cannot clear the disk in UEFI install

#11 2018-01-21 19:06:36

Re: [solved] cannot clear the disk in UEFI install

#12 2018-01-24 11:05:41

Re: [solved] cannot clear the disk in UEFI install

Board footer