Archlinux_x86_64_0.8.2 can't recognize hard disk on Acer aspire 4520g

faque · 2008-01-27 15:33:30

hello archers

I wanna switch from opensuse to arch, but arch can't recognize my hard disk.

My computer is Acer aspire 4520g:
AMD Athlon TK-55
2G Memory
NVIDIA GForce 8400M G graphic card
And an 80G Toshiba HD
--------------------------------------------
First time I install arch ISO (x86_64_0.8.2) image from harddisk, but the arch installer can't recognize the HD,
I notice the hard disk LED is always on.

And I reboot to try a second time, when loading installer I pass vga=0361 to kernel, this is a mistake, so vga=0361 is not
a valid parameter in my system (actually it should be vga=0x361), but amazing, when I continue the installation
after that mistake, the hard disk can be recognized, so I can install the core system.

But when installation is done, I reboot the system, the hard disk can not be recognized any more even I try to pass
vag=0361 to kernel.

Somebody can help me?

Thanks!

kozzi · 2008-02-01 12:34:19

Did you try to choose an ide-legacy?

faque · 2008-02-01 12:55:45

Yes, I tried.

In the bois I select IDE mode for SATA(another option is AHCI) to support booting WinXP.
But I tried both option, takes no effect!

I also tried the 11.0.4 ISO, this problem still exists!

byte · 2008-02-01 12:58:43

Post dmesg output after booting the -0.4 ISO.

faque · 2008-02-02 15:42:26

I use a USB DISK to save the output of dmesg, I also notice that the 11.0.4 installer turn down the lightness of my LCD screen(I passed vga=0x361 to the kernel).

Linux version 2.6.23-ARCH (root@T-POWA-LX) (gcc version 4.2.2) #1 SMP PREEMPT Sat Nov 17 18:23:00 CET 2007
Command line: vga=0x361
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009e000 (usable)
 BIOS-e820: 000000000009e000 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000007fed0000 (usable)
 BIOS-e820: 000000007fed0000 - 000000007fee5000 (ACPI data)
 BIOS-e820: 000000007fee5000 - 000000007fee6000 (ACPI NVS)
 BIOS-e820: 000000007fee6000 - 000000007ff00000 (reserved)
 BIOS-e820: 000000007ff80000 - 0000000080000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 158) 0 entries of 256 used
Entering add_active_range(0, 256, 523984) 1 entries of 256 used
end_pfn_map = 1048576
DMI present.
ACPI: RSDP 000F7E30, 0024 (r2 PTLTD )
ACPI: XSDT 7FEDE28D, 006C (r1 ACRSYS ACRPRDCT  6040000  LTP        0)
ACPI: FACP 7FEE492A, 00F4 (r3 NVIDIA MCP67-M   6040000 PTL_    F4240)
ACPI: DSDT 7FEDE2F9, 65BD (r1 NVIDIA    MCP67  6040000 MSFT  3000000)
ACPI: FACS 7FEE5FC0, 0040
ACPI: SRAT 7FEE4A1E, 00A0 (r1 AMD    HAMMER    6040000 AMD         1)
ACPI: WDAT 7FEE4ABE, 0104 (r1 PTLTD  WDATTBL   6040000  LTP        1)
ACPI: SSDT 7FEE4BC2, 01C4 (r1 PTLTD  POWERNOW  6040000  LTP        1)
ACPI: MCFG 7FEE4D86, 003C (r1 PTLTD    MCFG    6040000  LTP        0)
ACPI: HPET 7FEE4DC2, 0038 (r1 PTLTD  HPETTBL   6040000  LTP        1)
ACPI: APIC 7FEE4DFA, 0068 (r1 PTLTD       APIC    6040000  LTP        0)
ACPI: BOOT 7FEE4E62, 0028 (r1 PTLTD  $SBFTBL$  6040000  LTP        1)
ACPI: SLIC 7FEE4E8A, 0176 (r1 ACRSYS ACRPRDCT  6040000 acer        0)
Entering add_active_range(0, 0, 158) 0 entries of 256 used
Entering add_active_range(0, 256, 523984) 1 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  DMA32        4096 ->  1048576
  Normal    1048576 ->  1048576
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0:        0 ->      158
    0:      256 ->   523984
On node 0 totalpages: 523886
  DMA zone: 56 pages used for memmap
  DMA zone: 1174 pages reserved
  DMA zone: 2768 pages, LIFO batch:0
  DMA32 zone: 7107 pages used for memmap
  DMA32 zone: 512781 pages, LIFO batch:31
  Normal zone: 0 pages used for memmap
  Movable zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
ACPI: HPET id: 0x10de8201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
swsusp: Registered nosave memory region: 000000000009e000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000d0000
swsusp: Registered nosave memory region: 00000000000d0000 - 0000000000100000
Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 31080 bytes of per cpu data
Built 1 zonelists in Zone order.  Total pages: 515549
Kernel command line: vga=0x361
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000
Marking TSC unstable due to TSCs unsynchronized
time.c: Detected 1800.167 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Checking aperture...
CPU 0: aperture @ 278000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Memory: 2028316k/2095936k available (2761k kernel code, 66764k reserved, 1040k data, 252k init)
SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
Calibrating delay using timer specific routine.. 3604.37 BogoMIPS (lpj=6005395)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
SMP alternatives: switching to UP code
Early unpacking initramfs... done
ACPI: Core revision 20070126
ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
Using local APIC timer interrupts.
result 12501167
Detected 12.501 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 3601.41 BogoMIPS (lpj=6000666)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
AMD Athlon(tm) 64 X2 Dual-Core Processor TK-55 stepping 01
Brought up 2 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000 - e07fffff
PCI: No mmconfig possible on device 00:18
ACPI: EC: Look up EC in DSDT
ACPI: EC: GPE = 0x10, I/O: command/status = 0x66, data = 0x62
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x10, I/O: command/status = 0x66, data = 0x62
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:08.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR3._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LK1E] (IRQs 16 17 18 19 20) *0, disabled.
ACPI: PCI Interrupt Link [LK2E] (IRQs 16 17 18 19 20) *10
ACPI: PCI Interrupt Link [LK3E] (IRQs 16 17 18 19 20) *10
ACPI: PCI Interrupt Link [LK4E] (IRQs 16 17 18 19 20) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 16 17 18 19 20) *10
ACPI: PCI Interrupt Link [LUS0] (IRQs 16 17 18 19 20) *11
ACPI: PCI Interrupt Link [LUS2] (IRQs 16 17 18 19 20) *10
ACPI: PCI Interrupt Link [LMAC] (IRQs 16 17 18 19 20) *11
ACPI: PCI Interrupt Link [LAZA] (IRQs 16 17 18 19 20) *10
ACPI: PCI Interrupt Link [LGPU] (IRQs 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LPID] (IRQs 16 17 18 19 20) *0, disabled.
ACPI: PCI Interrupt Link [LSI0] (IRQs 16 17 18 19 20) *5
ACPI: PCI Interrupt Link [Z002] (IRQs 16 17 18 19 20) *7
ACPI: PCI Interrupt Link [Z003] (IRQs 16 17 18 19 20) *11
ACPI: PCI Interrupt Link [LPMU] (IRQs 16 17 18 19 20) *11
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Cannot allocate resource region 7 of bridge 0000:00:0c.0
PCI: Cannot allocate resource region 8 of bridge 0000:00:0c.0
PCI: Cannot allocate resource region 9 of bridge 0000:00:0c.0
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
ACPI: RTC can wake from S4
Time: hpet clocksource has been installed.
pnp: 00:02: iomem range 0xe0000000-0xefffffff could not be reserved
pnp: 00:03: ioport range 0x1000-0x107f has been reserved
pnp: 00:03: ioport range 0x1080-0x10ff has been reserved
pnp: 00:03: ioport range 0x1400-0x147f has been reserved
pnp: 00:03: ioport range 0x1480-0x14ff has been reserved
pnp: 00:03: ioport range 0x1800-0x187f has been reserved
pnp: 00:03: ioport range 0x1880-0x18ff has been reserved
pnp: 00:03: ioport range 0x3040-0x307f has been reserved
pnp: 00:03: ioport range 0x3000-0x303f has been reserved
pnp: 00:0b: iomem range 0xffc00000-0xffffffff could not be reserved
pnp: 00:0b: iomem range 0xfec00000-0xfec00fff could not be reserved
pnp: 00:0b: iomem range 0xfee00000-0xfeefffff could not be reserved
pnp: 00:0b: iomem range 0xfed00000-0xfed00fff has been reserved
PCI: Bridge: 0000:00:08.0
  IO window: disabled.
  MEM window: f2100000-f21fffff
  PREFETCH window: disabled.
PCI: Failed to allocate mem resource #6:20000@e0000000 for 0000:02:00.0
PCI: Bridge: 0000:00:0b.0
  IO window: 4000-4fff
  MEM window: cc000000-ceffffff
  PREFETCH window: d0000000-dfffffff
PCI: Bridge: 0000:00:0c.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:0e.0
  IO window: disabled.
  MEM window: f2000000-f20fffff
  PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:08.0 to 64
PCI: Setting latency timer of device 0000:00:0b.0 to 64
PCI: Setting latency timer of device 0000:00:0c.0 to 64
PCI: Setting latency timer of device 0000:00:0e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 131072 (order: 9, 3145728 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 30160k freed
Simple Boot Flag at 0x36 set to 0x1
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:02:00.0
PCI: Setting latency timer of device 0000:00:0b.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0b.0:pcie00]
Allocate Port Service[0000:00:0b.0:pcie03]
PCI: Setting latency timer of device 0000:00:0c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0c.0:pcie00]
Allocate Port Service[0000:00:0c.0:pcie03]
PCI: Setting latency timer of device 0000:00:0e.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0e.0:pcie00]
Allocate Port Service[0000:00:0e.0:pcie03]
vesafb: framebuffer at 0xcd000000, mapped to 0xffffc20000900000, using 8000k, total 14336k
vesafb: mode is 1280x800x32, linelength=5120, pages=1
vesafb: scrolling: redraw
vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
Console: switching to colour frame buffer device 160x50
fb0: VESA VGA frame buffer device
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input0
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 252k freed
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
input: Power Button (FF) as /devices/virtual/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /devices/virtual/input/input3
ACPI: Power Button (CM) [PWRB]
input: Lid Switch as /devices/virtual/input/input4
ACPI: Lid Switch [LID]
input: Sleep Button (CM) as /devices/virtual/input/input5
ACPI: Sleep Button (CM) [SLPB]
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI Exception (processor_core-0818): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0818): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI: Thermal Zone [THRM] (56 C)
input: Video Bus as /devices/virtual/input/input6
ACPI: Video Device [IGPU] (multi-head: yes  rom: no  post: no)
input: Video Bus as /devices/virtual/input/input7
ACPI: Video Device [Z004] (multi-head: yes  rom: no  post: no)
ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 10
ACPI: PCI Interrupt 0000:01:09.0[A] -> Link [LNK1] -> GSI 10 (level, low) -> IRQ 10
firewire_ohci: Added fw-ohci device 0000:01:09.0, OHCI version 1.10
rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
rtc_cmos: probe of 00:07 failed with error -16
ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [LAZA] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:07.0 to 64
hda_codec: Unknown model for ALC268, trying auto-probe from BIOS...
si3054: cannot initialize. EXT MID = 0000
libata version 2.21 loaded.
pata_amd 0000:00:06.0: version 0.3.9
PCI: Setting latency timer of device 0000:00:06.0 to 64
scsi0 : pata_amd
scsi1 : pata_amd
ata1: PATA max UDMA/133 cmd 0x00000000000101f0 ctl 0x00000000000103f6 bmdma 0x00000000000130c0 irq 14
ata2: PATA max UDMA/133 cmd 0x0000000000010170 ctl 0x0000000000010376 bmdma 0x00000000000130c8 irq 15
firewire_core: created new fw device fw0 (0 config rom retries, S400)
ata1.00: ATAPI: HL-DT-ST DVDRAM GSA-T20N, WP03, max UDMA/33
ata1.00: configured for UDMA/33
ata2: port disabled. ignoring.
scsi 0:0:0:0: CD-ROM            HL-DT-ST DVDRAM GSA-T20N  WP03 PQ: 0 ANSI: 5
ahci 0000:00:09.0: version 2.3
ACPI: PCI Interrupt Link [LSI0] enabled at IRQ 19
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LSI0] -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:09.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl IDE mode
ahci 0000:00:09.0: flags: 64bit sntf led clo pmp pio slum part 
PCI: Setting latency timer of device 0000:00:09.0 to 64
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata3: SATA max UDMA/133 cmd 0xffffc20000030100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 19
ata4: SATA max UDMA/133 cmd 0xffffc20000030180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 19
ata5: SATA max UDMA/133 cmd 0xffffc20000030200 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 19
ata6: SATA max UDMA/133 cmd 0xffffc20000030280 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 19
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
ata5: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.
ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 18
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LMAC] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:0a.0 to 64
forcedeth: using HIGHDMA
eth0: forcedeth.c: subsystem: 01025:0127 bound to 0000:00:0a.0
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
wlan: 0.8.4.2 (0.9.3.3)
ath_pci: 0.9.4.5 (0.9.3.3)
ACPI: PCI Interrupt Link [LK3E] enabled at IRQ 17
ACPI: PCI Interrupt 0000:07:00.0[A] -> Link [LK3E] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:07:00.0 to 64
wifi%d: unable to attach hardware: 'Hardware revision not supported' (HAL status 13)
ACPI: PCI interrupt for device 0000:07:00.0 disabled
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 16
ACPI: PCI Interrupt 0000:00:02.1[b] -> Link [LUS2] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: irq 16, io mem 0xf2489000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ACPI: PCI Interrupt Link [Z003] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:04.1[b] -> Link [Z003] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:04.1 to 64
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:04.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:04.1
ehci_hcd 0000:00:04.1: irq 20, io mem 0xf2489400
ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 19
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:02.0: irq 19, io mem 0xf2486000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
ACPI: PCI Interrupt Link [Z002] enabled at IRQ 18
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [Z002] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:04.0 to 64
ohci_hcd 0000:00:04.0: OHCI Host Controller
ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:04.0: irq 18, io mem 0xf2487000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 4 ports detected
usb 3-2: new low speed USB device using ohci_hcd and address 2
usb 3-2: configuration #1 chosen from 1 choice
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 0:0:0:0: Attached scsi CD-ROM sr0
usbcore: registered new interface driver hiddev
input: USB Mouse as /devices/pci0000:00/0000:00:02.0/usb3/3-2/3-2:1.0/input/input8
input: USB HID v1.10 Mouse [USB Mouse] on usb-0000:00:02.0-2
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
floppy0: no floppy controllers found
md: linear personality registered for level -1
md: multipath personality registered for level -4
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
xor: automatically using best checksumming function: generic_sse
   generic_sse:  5484.000 MB/sec
xor: using function: generic_sse (5484.000 MB/sec)
async_tx: api initialized (async)
raid6: int64x1   1757 MB/s
raid6: int64x2   2200 MB/s
raid6: int64x4   2264 MB/s
raid6: int64x8   1812 MB/s
raid6: sse2x1    2487 MB/s
raid6: sse2x2    3359 MB/s
raid6: sse2x4    3451 MB/s
raid6: using algorithm sse2x4 (3451 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: raid10 personality registered for level 10
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
usb 3-4: new full speed USB device using ohci_hcd and address 3
usb 3-4: configuration #1 chosen from 1 choice
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Initializing USB Mass Storage driver...
scsi6 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
scsi 6:0:0:0: Direct-Access     NEWMAN   FLASH !DISK      %z!Y PQ: 0 ANSI: 2
usb-storage: device scan complete
sd 6:0:0:0: [sda] 128544 512-byte hardware sectors (66 MB)
sd 6:0:0:0: [sda] Write Protect is off
sd 6:0:0:0: [sda] Mode Sense: 0b 00 00 08
sd 6:0:0:0: [sda] Assuming drive cache: write through
sd 6:0:0:0: [sda] 128544 512-byte hardware sectors (66 MB)
sd 6:0:0:0: [sda] Write Protect is off
sd 6:0:0:0: [sda] Mode Sense: 0b 00 00 08
sd 6:0:0:0: [sda] Assuming drive cache: write through
 sda: sda1
sd 6:0:0:0: [sda] Attached SCSI removable disk

byte · 2008-02-03 05:14:31

Shot in the dark: Try disabling AHCI in the bios / boot with "arch disablemodules=ahci"

faque · 2008-02-04 15:45:35

byte wrote:

Shot in the dark: Try disabling AHCI in the bios / boot with "arch disablemodules=ahci"

This can not work.

And I have tried several schemes, just found out that I need to pass the wrong vga parameter to the kernel as mentioned before.
Below are the outputs of dmesg.

1. just past vga=361 to kernel, it works!

Linux version 2.6.23-ARCH (root@T-POWA-LX) (gcc version 4.2.2) #1 SMP PREEMPT Sat Nov 17 18:23:00 CET 2007
Command line: vga=361
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009e000 (usable)
 BIOS-e820: 000000000009e000 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000007fed0000 (usable)
 BIOS-e820: 000000007fed0000 - 000000007fee5000 (ACPI data)
 BIOS-e820: 000000007fee5000 - 000000007fee6000 (ACPI NVS)
 BIOS-e820: 000000007fee6000 - 000000007ff00000 (reserved)
 BIOS-e820: 000000007ff80000 - 0000000080000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 158) 0 entries of 256 used
Entering add_active_range(0, 256, 523984) 1 entries of 256 used
end_pfn_map = 1048576
DMI present.
ACPI: RSDP 000F7E30, 0024 (r2 PTLTD )
ACPI: XSDT 7FEDE28D, 006C (r1 ACRSYS ACRPRDCT  6040000  LTP        0)
ACPI: FACP 7FEE492A, 00F4 (r3 NVIDIA MCP67-M   6040000 PTL_    F4240)
ACPI: DSDT 7FEDE2F9, 65BD (r1 NVIDIA    MCP67  6040000 MSFT  3000000)
ACPI: FACS 7FEE5FC0, 0040
ACPI: SRAT 7FEE4A1E, 00A0 (r1 AMD    HAMMER    6040000 AMD         1)
ACPI: WDAT 7FEE4ABE, 0104 (r1 PTLTD  WDATTBL   6040000  LTP        1)
ACPI: SSDT 7FEE4BC2, 01C4 (r1 PTLTD  POWERNOW  6040000  LTP        1)
ACPI: MCFG 7FEE4D86, 003C (r1 PTLTD    MCFG    6040000  LTP        0)
ACPI: HPET 7FEE4DC2, 0038 (r1 PTLTD  HPETTBL   6040000  LTP        1)
ACPI: APIC 7FEE4DFA, 0068 (r1 PTLTD       APIC    6040000  LTP        0)
ACPI: BOOT 7FEE4E62, 0028 (r1 PTLTD  $SBFTBL$  6040000  LTP        1)
ACPI: SLIC 7FEE4E8A, 0176 (r1 ACRSYS ACRPRDCT  6040000 acer        0)
Entering add_active_range(0, 0, 158) 0 entries of 256 used
Entering add_active_range(0, 256, 523984) 1 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  DMA32        4096 ->  1048576
  Normal    1048576 ->  1048576
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0:        0 ->      158
    0:      256 ->   523984
On node 0 totalpages: 523886
  DMA zone: 56 pages used for memmap
  DMA zone: 1174 pages reserved
  DMA zone: 2768 pages, LIFO batch:0
  DMA32 zone: 7107 pages used for memmap
  DMA32 zone: 512781 pages, LIFO batch:31
  Normal zone: 0 pages used for memmap
  Movable zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
ACPI: HPET id: 0x10de8201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
swsusp: Registered nosave memory region: 000000000009e000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000d0000
swsusp: Registered nosave memory region: 00000000000d0000 - 0000000000100000
Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 31080 bytes of per cpu data
Built 1 zonelists in Zone order.  Total pages: 515549
Kernel command line: vga=361
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000
Marking TSC unstable due to TSCs unsynchronized
time.c: Detected 1800.168 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Checking aperture...
CPU 0: aperture @ 27c000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Memory: 2028316k/2095936k available (2761k kernel code, 66764k reserved, 1040k data, 252k init)
SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
Calibrating delay using timer specific routine.. 3604.38 BogoMIPS (lpj=6005412)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
SMP alternatives: switching to UP code
Early unpacking initramfs... done
ACPI: Core revision 20070126
ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
Using local APIC timer interrupts.
result 12501158
Detected 12.501 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 3601.37 BogoMIPS (lpj=6000604)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
AMD Athlon(tm) 64 X2 Dual-Core Processor TK-55 stepping 01
Brought up 2 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000 - e07fffff
PCI: No mmconfig possible on device 00:18
ACPI: EC: Look up EC in DSDT
ACPI: EC: GPE = 0x10, I/O: command/status = 0x66, data = 0x62
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x10, I/O: command/status = 0x66, data = 0x62
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:08.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR3._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LK1E] (IRQs 16 17 18 19 20) *0, disabled.
ACPI: PCI Interrupt Link [LK2E] (IRQs 16 17 18 19 20) *10
ACPI: PCI Interrupt Link [LK3E] (IRQs 16 17 18 19 20) *10
ACPI: PCI Interrupt Link [LK4E] (IRQs 16 17 18 19 20) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 16 17 18 19 20) *10
ACPI: PCI Interrupt Link [LUS0] (IRQs 16 17 18 19 20) *11
ACPI: PCI Interrupt Link [LUS2] (IRQs 16 17 18 19 20) *10
ACPI: PCI Interrupt Link [LMAC] (IRQs 16 17 18 19 20) *11
ACPI: PCI Interrupt Link [LAZA] (IRQs 16 17 18 19 20) *10
ACPI: PCI Interrupt Link [LGPU] (IRQs 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LPID] (IRQs 16 17 18 19 20) *0, disabled.
ACPI: PCI Interrupt Link [LSI0] (IRQs 16 17 18 19 20) *5
ACPI: PCI Interrupt Link [Z002] (IRQs 16 17 18 19 20) *7
ACPI: PCI Interrupt Link [Z003] (IRQs 16 17 18 19 20) *11
ACPI: PCI Interrupt Link [LPMU] (IRQs 16 17 18 19 20) *11
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Cannot allocate resource region 7 of bridge 0000:00:0c.0
PCI: Cannot allocate resource region 8 of bridge 0000:00:0c.0
PCI: Cannot allocate resource region 9 of bridge 0000:00:0c.0
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
ACPI: RTC can wake from S4
Time: hpet clocksource has been installed.
pnp: 00:02: iomem range 0xe0000000-0xefffffff could not be reserved
pnp: 00:03: ioport range 0x1000-0x107f has been reserved
pnp: 00:03: ioport range 0x1080-0x10ff has been reserved
pnp: 00:03: ioport range 0x1400-0x147f has been reserved
pnp: 00:03: ioport range 0x1480-0x14ff has been reserved
pnp: 00:03: ioport range 0x1800-0x187f has been reserved
pnp: 00:03: ioport range 0x1880-0x18ff has been reserved
pnp: 00:03: ioport range 0x3040-0x307f has been reserved
pnp: 00:03: ioport range 0x3000-0x303f has been reserved
pnp: 00:0b: iomem range 0xffc00000-0xffffffff could not be reserved
pnp: 00:0b: iomem range 0xfec00000-0xfec00fff could not be reserved
pnp: 00:0b: iomem range 0xfee00000-0xfeefffff could not be reserved
pnp: 00:0b: iomem range 0xfed00000-0xfed00fff has been reserved
PCI: Bridge: 0000:00:08.0
  IO window: disabled.
  MEM window: f2100000-f21fffff
  PREFETCH window: disabled.
PCI: Failed to allocate mem resource #6:20000@e0000000 for 0000:02:00.0
PCI: Bridge: 0000:00:0b.0
  IO window: 4000-4fff
  MEM window: cc000000-ceffffff
  PREFETCH window: d0000000-dfffffff
PCI: Bridge: 0000:00:0c.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:0e.0
  IO window: disabled.
  MEM window: f2000000-f20fffff
  PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:08.0 to 64
PCI: Setting latency timer of device 0000:00:0b.0 to 64
PCI: Setting latency timer of device 0000:00:0c.0 to 64
PCI: Setting latency timer of device 0000:00:0e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 131072 (order: 9, 3145728 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 30160k freed
Simple Boot Flag at 0x36 set to 0x1
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:02:00.0
PCI: Setting latency timer of device 0000:00:0b.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0b.0:pcie00]
Allocate Port Service[0000:00:0b.0:pcie03]
PCI: Setting latency timer of device 0000:00:0c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0c.0:pcie00]
Allocate Port Service[0000:00:0c.0:pcie03]
PCI: Setting latency timer of device 0000:00:0e.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0e.0:pcie00]
Allocate Port Service[0000:00:0e.0:pcie03]
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input0
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 252k freed
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
input: Power Button (FF) as /devices/virtual/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /devices/virtual/input/input3
ACPI: Power Button (CM) [PWRB]
input: Lid Switch as /devices/virtual/input/input4
ACPI: Lid Switch [LID]
input: Sleep Button (CM) as /devices/virtual/input/input5
ACPI: Sleep Button (CM) [SLPB]
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI Exception (processor_core-0818): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0818): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI: Thermal Zone [THRM] (51 C)
input: Video Bus as /devices/virtual/input/input6
ACPI: Video Device [IGPU] (multi-head: yes  rom: no  post: no)
input: Video Bus as /devices/virtual/input/input7
ACPI: Video Device [Z004] (multi-head: yes  rom: no  post: no)
ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 10
ACPI: PCI Interrupt 0000:01:09.0[A] -> Link [LNK1] -> GSI 10 (level, low) -> IRQ 10
firewire_ohci: Added fw-ohci device 0000:01:09.0, OHCI version 1.10
rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
rtc_cmos: probe of 00:07 failed with error -16
ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [LAZA] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:07.0 to 64
hda_codec: Unknown model for ALC268, trying auto-probe from BIOS...
si3054: cannot initialize. EXT MID = 0000
libata version 2.21 loaded.
pata_amd 0000:00:06.0: version 0.3.9
PCI: Setting latency timer of device 0000:00:06.0 to 64
scsi0 : pata_amd
scsi1 : pata_amd
ata1: PATA max UDMA/133 cmd 0x00000000000101f0 ctl 0x00000000000103f6 bmdma 0x00000000000130c0 irq 14
ata2: PATA max UDMA/133 cmd 0x0000000000010170 ctl 0x0000000000010376 bmdma 0x00000000000130c8 irq 15
firewire_core: created new fw device fw0 (0 config rom retries, S400)
ata1.00: ATAPI: HL-DT-ST DVDRAM GSA-T20N, WP03, max UDMA/33
ata1.00: configured for UDMA/33
ata2: port disabled. ignoring.
scsi 0:0:0:0: CD-ROM            HL-DT-ST DVDRAM GSA-T20N  WP03 PQ: 0 ANSI: 5
ahci 0000:00:09.0: version 2.3
ACPI: PCI Interrupt Link [LSI0] enabled at IRQ 19
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LSI0] -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:09.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl IDE mode
ahci 0000:00:09.0: flags: 64bit sntf led clo pmp pio slum part 
PCI: Setting latency timer of device 0000:00:09.0 to 64
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata3: SATA max UDMA/133 cmd 0xffffc20000030100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 19
ata4: SATA max UDMA/133 cmd 0xffffc20000030180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 19
ata5: SATA max UDMA/133 cmd 0xffffc20000030200 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 19
ata6: SATA max UDMA/133 cmd 0xffffc20000030280 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 19
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATA-7: TOSHIBA MK8037GSX, DL250J, max UDMA/100
ata3.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata3.00: configured for UDMA/100
ata4: SATA link down (SStatus 0 SControl 300)
ata5: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
scsi 2:0:0:0: Direct-Access     ATA      TOSHIBA MK8037GS DL25 PQ: 0 ANSI: 5
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.
ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 18
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LMAC] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:0a.0 to 64
forcedeth: using HIGHDMA
eth0: forcedeth.c: subsystem: 01025:0127 bound to 0000:00:0a.0
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
wlan: 0.8.4.2 (0.9.3.3)
ath_pci: 0.9.4.5 (0.9.3.3)
ACPI: PCI Interrupt Link [LK3E] enabled at IRQ 17
ACPI: PCI Interrupt 0000:07:00.0[A] -> Link [LK3E] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:07:00.0 to 64
wifi%d: unable to attach hardware: 'Hardware revision not supported' (HAL status 13)
ACPI: PCI interrupt for device 0000:07:00.0 disabled
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 16
ACPI: PCI Interrupt 0000:00:02.1[b] -> Link [LUS2] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: irq 16, io mem 0xf2489000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ACPI: PCI Interrupt Link [Z003] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:04.1[b] -> Link [Z003] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:04.1 to 64
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:04.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:04.1
ehci_hcd 0000:00:04.1: irq 20, io mem 0xf2489400
ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 19
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:02.0: irq 19, io mem 0xf2486000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
ACPI: PCI Interrupt Link [Z002] enabled at IRQ 18
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [Z002] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:04.0 to 64
ohci_hcd 0000:00:04.0: OHCI Host Controller
ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:04.0: irq 18, io mem 0xf2487000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 4 ports detected
usb 3-2: new low speed USB device using ohci_hcd and address 2
usb 3-2: configuration #1 chosen from 1 choice
sd 2:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 > sda3
sd 2:0:0:0: [sda] Attached SCSI disk
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 0:0:0:0: Attached scsi CD-ROM sr0
usbcore: registered new interface driver hiddev
input: USB Mouse as /devices/pci0000:00/0000:00:02.0/usb3/3-2/3-2:1.0/input/input8
input: USB HID v1.10 Mouse [USB Mouse] on usb-0000:00:02.0-2
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
floppy0: no floppy controllers found
md: linear personality registered for level -1
md: multipath personality registered for level -4
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
xor: automatically using best checksumming function: generic_sse
   generic_sse:  5484.000 MB/sec
xor: using function: generic_sse (5484.000 MB/sec)
async_tx: api initialized (async)
raid6: int64x1   1760 MB/s
raid6: int64x2   2205 MB/s
raid6: int64x4   2273 MB/s
raid6: int64x8   1815 MB/s
raid6: sse2x1    2489 MB/s
raid6: sse2x2    3359 MB/s
raid6: sse2x4    3451 MB/s
raid6: using algorithm sse2x4 (3451 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: raid10 personality registered for level 10
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
usb 3-1: new full speed USB device using ohci_hcd and address 3
usb 3-1: configuration #1 chosen from 1 choice
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Initializing USB Mass Storage driver...
scsi6 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
scsi 6:0:0:0: Direct-Access     NEWMAN   FLASH !DISK      %z!Y PQ: 0 ANSI: 2
sd 6:0:0:0: [sdb] 128544 512-byte hardware sectors (66 MB)
sd 6:0:0:0: [sdb] Write Protect is off
sd 6:0:0:0: [sdb] Mode Sense: 0b 00 00 08
sd 6:0:0:0: [sdb] Assuming drive cache: write through
sd 6:0:0:0: [sdb] 128544 512-byte hardware sectors (66 MB)
sd 6:0:0:0: [sdb] Write Protect is off
sd 6:0:0:0: [sdb] Mode Sense: 0b 00 00 08
sd 6:0:0:0: [sdb] Assuming drive cache: write through
 sdb: sdb1
sd 6:0:0:0: [sdb] Attached SCSI removable disk
usb-storage: device scan complete

2. pass vga=361 and ide-legacy to kernel , it works too!

Linux version 2.6.23-ARCH (root@T-POWA-LX) (gcc version 4.2.2) #1 SMP PREEMPT Sat Nov 17 18:23:00 CET 2007
Command line: vga=361 ide-legacy
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009e000 (usable)
 BIOS-e820: 000000000009e000 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000007fed0000 (usable)
 BIOS-e820: 000000007fed0000 - 000000007fee5000 (ACPI data)
 BIOS-e820: 000000007fee5000 - 000000007fee6000 (ACPI NVS)
 BIOS-e820: 000000007fee6000 - 000000007ff00000 (reserved)
 BIOS-e820: 000000007ff80000 - 0000000080000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 158) 0 entries of 256 used
Entering add_active_range(0, 256, 523984) 1 entries of 256 used
end_pfn_map = 1048576
DMI present.
ACPI: RSDP 000F7E30, 0024 (r2 PTLTD )
ACPI: XSDT 7FEDE28D, 006C (r1 ACRSYS ACRPRDCT  6040000  LTP        0)
ACPI: FACP 7FEE492A, 00F4 (r3 NVIDIA MCP67-M   6040000 PTL_    F4240)
ACPI: DSDT 7FEDE2F9, 65BD (r1 NVIDIA    MCP67  6040000 MSFT  3000000)
ACPI: FACS 7FEE5FC0, 0040
ACPI: SRAT 7FEE4A1E, 00A0 (r1 AMD    HAMMER    6040000 AMD         1)
ACPI: WDAT 7FEE4ABE, 0104 (r1 PTLTD  WDATTBL   6040000  LTP        1)
ACPI: SSDT 7FEE4BC2, 01C4 (r1 PTLTD  POWERNOW  6040000  LTP        1)
ACPI: MCFG 7FEE4D86, 003C (r1 PTLTD    MCFG    6040000  LTP        0)
ACPI: HPET 7FEE4DC2, 0038 (r1 PTLTD  HPETTBL   6040000  LTP        1)
ACPI: APIC 7FEE4DFA, 0068 (r1 PTLTD       APIC    6040000  LTP        0)
ACPI: BOOT 7FEE4E62, 0028 (r1 PTLTD  $SBFTBL$  6040000  LTP        1)
ACPI: SLIC 7FEE4E8A, 0176 (r1 ACRSYS ACRPRDCT  6040000 acer        0)
Entering add_active_range(0, 0, 158) 0 entries of 256 used
Entering add_active_range(0, 256, 523984) 1 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  DMA32        4096 ->  1048576
  Normal    1048576 ->  1048576
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0:        0 ->      158
    0:      256 ->   523984
On node 0 totalpages: 523886
  DMA zone: 56 pages used for memmap
  DMA zone: 1174 pages reserved
  DMA zone: 2768 pages, LIFO batch:0
  DMA32 zone: 7107 pages used for memmap
  DMA32 zone: 512781 pages, LIFO batch:31
  Normal zone: 0 pages used for memmap
  Movable zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
ACPI: HPET id: 0x10de8201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
swsusp: Registered nosave memory region: 000000000009e000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000d0000
swsusp: Registered nosave memory region: 00000000000d0000 - 0000000000100000
Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 31080 bytes of per cpu data
Built 1 zonelists in Zone order.  Total pages: 515549
Kernel command line: vga=361 ide-legacy
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000
Marking TSC unstable due to TSCs unsynchronized
time.c: Detected 1800.167 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Checking aperture...
CPU 0: aperture @ 678000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Memory: 2028316k/2095936k available (2761k kernel code, 66764k reserved, 1040k data, 252k init)
SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
Calibrating delay using timer specific routine.. 3604.37 BogoMIPS (lpj=6005405)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
SMP alternatives: switching to UP code
Early unpacking initramfs... done
ACPI: Core revision 20070126
ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
Using local APIC timer interrupts.
result 12501166
Detected 12.501 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 3601.39 BogoMIPS (lpj=6000625)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
AMD Athlon(tm) 64 X2 Dual-Core Processor TK-55 stepping 01
Brought up 2 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000 - e07fffff
PCI: No mmconfig possible on device 00:18
ACPI: EC: Look up EC in DSDT
ACPI: EC: GPE = 0x10, I/O: command/status = 0x66, data = 0x62
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x10, I/O: command/status = 0x66, data = 0x62
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:08.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR3._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LK1E] (IRQs 16 17 18 19 20) *0, disabled.
ACPI: PCI Interrupt Link [LK2E] (IRQs 16 17 18 19 20) *10
ACPI: PCI Interrupt Link [LK3E] (IRQs 16 17 18 19 20) *10
ACPI: PCI Interrupt Link [LK4E] (IRQs 16 17 18 19 20) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 16 17 18 19 20) *10
ACPI: PCI Interrupt Link [LUS0] (IRQs 16 17 18 19 20) *11
ACPI: PCI Interrupt Link [LUS2] (IRQs 16 17 18 19 20) *10
ACPI: PCI Interrupt Link [LMAC] (IRQs 16 17 18 19 20) *11
ACPI: PCI Interrupt Link [LAZA] (IRQs 16 17 18 19 20) *10
ACPI: PCI Interrupt Link [LGPU] (IRQs 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LPID] (IRQs 16 17 18 19 20) *0, disabled.
ACPI: PCI Interrupt Link [LSI0] (IRQs 16 17 18 19 20) *5
ACPI: PCI Interrupt Link [Z002] (IRQs 16 17 18 19 20) *7
ACPI: PCI Interrupt Link [Z003] (IRQs 16 17 18 19 20) *11
ACPI: PCI Interrupt Link [LPMU] (IRQs 16 17 18 19 20) *11
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Cannot allocate resource region 7 of bridge 0000:00:0c.0
PCI: Cannot allocate resource region 8 of bridge 0000:00:0c.0
PCI: Cannot allocate resource region 9 of bridge 0000:00:0c.0
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
ACPI: RTC can wake from S4
Time: hpet clocksource has been installed.
pnp: 00:02: iomem range 0xe0000000-0xefffffff could not be reserved
pnp: 00:03: ioport range 0x1000-0x107f has been reserved
pnp: 00:03: ioport range 0x1080-0x10ff has been reserved
pnp: 00:03: ioport range 0x1400-0x147f has been reserved
pnp: 00:03: ioport range 0x1480-0x14ff has been reserved
pnp: 00:03: ioport range 0x1800-0x187f has been reserved
pnp: 00:03: ioport range 0x1880-0x18ff has been reserved
pnp: 00:03: ioport range 0x3040-0x307f has been reserved
pnp: 00:03: ioport range 0x3000-0x303f has been reserved
pnp: 00:0b: iomem range 0xffc00000-0xffffffff could not be reserved
pnp: 00:0b: iomem range 0xfec00000-0xfec00fff could not be reserved
pnp: 00:0b: iomem range 0xfee00000-0xfeefffff could not be reserved
pnp: 00:0b: iomem range 0xfed00000-0xfed00fff has been reserved
PCI: Bridge: 0000:00:08.0
  IO window: disabled.
  MEM window: f2100000-f21fffff
  PREFETCH window: disabled.
PCI: Failed to allocate mem resource #6:20000@e0000000 for 0000:02:00.0
PCI: Bridge: 0000:00:0b.0
  IO window: 4000-4fff
  MEM window: cc000000-ceffffff
  PREFETCH window: d0000000-dfffffff
PCI: Bridge: 0000:00:0c.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:0e.0
  IO window: disabled.
  MEM window: f2000000-f20fffff
  PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:08.0 to 64
PCI: Setting latency timer of device 0000:00:0b.0 to 64
PCI: Setting latency timer of device 0000:00:0c.0 to 64
PCI: Setting latency timer of device 0000:00:0e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 131072 (order: 9, 3145728 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 30160k freed
Simple Boot Flag at 0x36 set to 0x1
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:02:00.0
PCI: Setting latency timer of device 0000:00:0b.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0b.0:pcie00]
Allocate Port Service[0000:00:0b.0:pcie03]
PCI: Setting latency timer of device 0000:00:0c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0c.0:pcie00]
Allocate Port Service[0000:00:0c.0:pcie03]
PCI: Setting latency timer of device 0000:00:0e.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0e.0:pcie00]
Allocate Port Service[0000:00:0e.0:pcie03]
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input0
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 252k freed
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
input: Power Button (FF) as /devices/virtual/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /devices/virtual/input/input3
ACPI: Power Button (CM) [PWRB]
input: Lid Switch as /devices/virtual/input/input4
ACPI: Lid Switch [LID]
input: Sleep Button (CM) as /devices/virtual/input/input5
ACPI: Sleep Button (CM) [SLPB]
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI Exception (processor_core-0818): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0818): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI: Thermal Zone [THRM] (63 C)
input: Video Bus as /devices/virtual/input/input6
ACPI: Video Device [IGPU] (multi-head: yes  rom: no  post: no)
input: Video Bus as /devices/virtual/input/input7
ACPI: Video Device [Z004] (multi-head: yes  rom: no  post: no)
ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 10
ACPI: PCI Interrupt 0000:01:09.0[A] -> Link [LNK1] -> GSI 10 (level, low) -> IRQ 10
firewire_ohci: Added fw-ohci device 0000:01:09.0, OHCI version 1.10
rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
rtc_cmos: probe of 00:07 failed with error -16
ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [LAZA] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:07.0 to 64
hda_codec: Unknown model for ALC268, trying auto-probe from BIOS...
si3054: cannot initialize. EXT MID = 0000
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-MCP67: IDE controller at PCI slot 0000:00:06.0
NFORCE-MCP67: chipset revision 161
NFORCE-MCP67: not 100% native mode: will probe irqs later
NFORCE-MCP67: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE-MCP67: 0000:00:06.0 (rev a1) UDMA133 controller
    ide0: BM-DMA at 0x30c0-0x30c7, BIOS settings: hda:DMA, hdb:pio
Probing IDE interface ide0...
firewire_core: created new fw device fw0 (0 config rom retries, S400)
hda: HL-DT-ST DVDRAM GSA-T20N, ATAPI CD/DVD-ROM drive
hda: selected mode 0x42
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
libata version 2.21 loaded.
ahci 0000:00:09.0: version 2.3
ACPI: PCI Interrupt Link [LSI0] enabled at IRQ 19
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LSI0] -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:09.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl IDE mode
ahci 0000:00:09.0: flags: 64bit sntf led clo pmp pio slum part 
PCI: Setting latency timer of device 0000:00:09.0 to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 cmd 0xffffc20000030100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 19
ata2: SATA max UDMA/133 cmd 0xffffc20000030180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 19
ata3: SATA max UDMA/133 cmd 0xffffc20000030200 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 19
ata4: SATA max UDMA/133 cmd 0xffffc20000030280 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 19
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: TOSHIBA MK8037GSX, DL250J, max UDMA/100
ata1.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/100
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access     ATA      TOSHIBA MK8037GS DL25 PQ: 0 ANSI: 5
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.
ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 18
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LMAC] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:0a.0 to 64
forcedeth: using HIGHDMA
eth0: forcedeth.c: subsystem: 01025:0127 bound to 0000:00:0a.0
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
wlan: 0.8.4.2 (0.9.3.3)
ath_pci: 0.9.4.5 (0.9.3.3)
ACPI: PCI Interrupt Link [LK3E] enabled at IRQ 17
ACPI: PCI Interrupt 0000:07:00.0[A] -> Link [LK3E] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:07:00.0 to 64
wifi%d: unable to attach hardware: 'Hardware revision not supported' (HAL status 13)
ACPI: PCI interrupt for device 0000:07:00.0 disabled
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 16
ACPI: PCI Interrupt 0000:00:02.1[b] -> Link [LUS2] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: irq 16, io mem 0xf2489000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ACPI: PCI Interrupt Link [Z003] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:04.1[b] -> Link [Z003] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:04.1 to 64
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:04.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:04.1
ehci_hcd 0000:00:04.1: irq 20, io mem 0xf2489400
ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 19
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:02.0: irq 19, io mem 0xf2486000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
ACPI: PCI Interrupt Link [Z002] enabled at IRQ 18
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [Z002] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:04.0 to 64
ohci_hcd 0000:00:04.0: OHCI Host Controller
ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:04.0: irq 18, io mem 0xf2487000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 4 ports detected
usb 3-2: new low speed USB device using ohci_hcd and address 2
usb 3-2: configuration #1 chosen from 1 choice
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 > sda3
sd 0:0:0:0: [sda] Attached SCSI disk
hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
usbcore: registered new interface driver hiddev
input: USB Mouse as /devices/pci0000:00/0000:00:02.0/usb3/3-2/3-2:1.0/input/input8
input: USB HID v1.10 Mouse [USB Mouse] on usb-0000:00:02.0-2
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
floppy0: no floppy controllers found
md: linear personality registered for level -1
md: multipath personality registered for level -4
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
xor: automatically using best checksumming function: generic_sse
   generic_sse:  5486.400 MB/sec
xor: using function: generic_sse (5486.400 MB/sec)
async_tx: api initialized (async)
raid6: int64x1   1781 MB/s
raid6: int64x2   2221 MB/s
raid6: int64x4   2269 MB/s
raid6: int64x8   1814 MB/s
raid6: sse2x1    2513 MB/s
raid6: sse2x2    3030 MB/s
raid6: sse2x4    3185 MB/s
raid6: using algorithm sse2x4 (3185 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: raid10 personality registered for level 10
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
usb 3-1: new full speed USB device using ohci_hcd and address 3
usb 3-1: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
scsi 4:0:0:0: Direct-Access     NEWMAN   FLASH !DISK      %z!Y PQ: 0 ANSI: 2
sd 4:0:0:0: [sdb] 128544 512-byte hardware sectors (66 MB)
sd 4:0:0:0: [sdb] Write Protect is off
sd 4:0:0:0: [sdb] Mode Sense: 0b 00 00 08
sd 4:0:0:0: [sdb] Assuming drive cache: write through
sd 4:0:0:0: [sdb] 128544 512-byte hardware sectors (66 MB)
sd 4:0:0:0: [sdb] Write Protect is off
sd 4:0:0:0: [sdb] Mode Sense: 0b 00 00 08
sd 4:0:0:0: [sdb] Assuming drive cache: write through
 sdb: sdb1
sd 4:0:0:0: [sdb] Attached SCSI removable disk
usb-storage: device scan complete

3. ide-legacy only, can not work!

Linux version 2.6.23-ARCH (root@T-POWA-LX) (gcc version 4.2.2) #1 SMP PREEMPT Sat Nov 17 18:23:00 CET 2007
Command line: ide-legacy
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009e000 (usable)
 BIOS-e820: 000000000009e000 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000007fed0000 (usable)
 BIOS-e820: 000000007fed0000 - 000000007fee5000 (ACPI data)
 BIOS-e820: 000000007fee5000 - 000000007fee6000 (ACPI NVS)
 BIOS-e820: 000000007fee6000 - 000000007ff00000 (reserved)
 BIOS-e820: 000000007ff80000 - 0000000080000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 158) 0 entries of 256 used
Entering add_active_range(0, 256, 523984) 1 entries of 256 used
end_pfn_map = 1048576
DMI present.
ACPI: RSDP 000F7E30, 0024 (r2 PTLTD )
ACPI: XSDT 7FEDE28D, 006C (r1 ACRSYS ACRPRDCT  6040000  LTP        0)
ACPI: FACP 7FEE492A, 00F4 (r3 NVIDIA MCP67-M   6040000 PTL_    F4240)
ACPI: DSDT 7FEDE2F9, 65BD (r1 NVIDIA    MCP67  6040000 MSFT  3000000)
ACPI: FACS 7FEE5FC0, 0040
ACPI: SRAT 7FEE4A1E, 00A0 (r1 AMD    HAMMER    6040000 AMD         1)
ACPI: WDAT 7FEE4ABE, 0104 (r1 PTLTD  WDATTBL   6040000  LTP        1)
ACPI: SSDT 7FEE4BC2, 01C4 (r1 PTLTD  POWERNOW  6040000  LTP        1)
ACPI: MCFG 7FEE4D86, 003C (r1 PTLTD    MCFG    6040000  LTP        0)
ACPI: HPET 7FEE4DC2, 0038 (r1 PTLTD  HPETTBL   6040000  LTP        1)
ACPI: APIC 7FEE4DFA, 0068 (r1 PTLTD       APIC    6040000  LTP        0)
ACPI: BOOT 7FEE4E62, 0028 (r1 PTLTD  $SBFTBL$  6040000  LTP        1)
ACPI: SLIC 7FEE4E8A, 0176 (r1 ACRSYS ACRPRDCT  6040000 acer        0)
Entering add_active_range(0, 0, 158) 0 entries of 256 used
Entering add_active_range(0, 256, 523984) 1 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  DMA32        4096 ->  1048576
  Normal    1048576 ->  1048576
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0:        0 ->      158
    0:      256 ->   523984
On node 0 totalpages: 523886
  DMA zone: 56 pages used for memmap
  DMA zone: 1174 pages reserved
  DMA zone: 2768 pages, LIFO batch:0
  DMA32 zone: 7107 pages used for memmap
  DMA32 zone: 512781 pages, LIFO batch:31
  Normal zone: 0 pages used for memmap
  Movable zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
ACPI: HPET id: 0x10de8201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
swsusp: Registered nosave memory region: 000000000009e000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000d0000
swsusp: Registered nosave memory region: 00000000000d0000 - 0000000000100000
Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 31080 bytes of per cpu data
Built 1 zonelists in Zone order.  Total pages: 515549
Kernel command line: ide-legacy
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000
Marking TSC unstable due to TSCs unsynchronized
time.c: Detected 1800.167 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Checking aperture...
CPU 0: aperture @ 27c000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Memory: 2028316k/2095936k available (2761k kernel code, 66764k reserved, 1040k data, 252k init)
SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
Calibrating delay using timer specific routine.. 3604.39 BogoMIPS (lpj=6005424)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
SMP alternatives: switching to UP code
Early unpacking initramfs... done
ACPI: Core revision 20070126
ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
Using local APIC timer interrupts.
result 12501151
Detected 12.501 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 3601.36 BogoMIPS (lpj=6000579)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
AMD Athlon(tm) 64 X2 Dual-Core Processor TK-55 stepping 01
Brought up 2 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000 - e07fffff
PCI: No mmconfig possible on device 00:18
ACPI: EC: Look up EC in DSDT
ACPI: EC: GPE = 0x10, I/O: command/status = 0x66, data = 0x62
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x10, I/O: command/status = 0x66, data = 0x62
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:08.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR3._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LK1E] (IRQs 16 17 18 19 20) *0, disabled.
ACPI: PCI Interrupt Link [LK2E] (IRQs 16 17 18 19 20) *10
ACPI: PCI Interrupt Link [LK3E] (IRQs 16 17 18 19 20) *10
ACPI: PCI Interrupt Link [LK4E] (IRQs 16 17 18 19 20) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 16 17 18 19 20) *10
ACPI: PCI Interrupt Link [LUS0] (IRQs 16 17 18 19 20) *11
ACPI: PCI Interrupt Link [LUS2] (IRQs 16 17 18 19 20) *10
ACPI: PCI Interrupt Link [LMAC] (IRQs 16 17 18 19 20) *11
ACPI: PCI Interrupt Link [LAZA] (IRQs 16 17 18 19 20) *10
ACPI: PCI Interrupt Link [LGPU] (IRQs 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LPID] (IRQs 16 17 18 19 20) *0, disabled.
ACPI: PCI Interrupt Link [LSI0] (IRQs 16 17 18 19 20) *5
ACPI: PCI Interrupt Link [Z002] (IRQs 16 17 18 19 20) *7
ACPI: PCI Interrupt Link [Z003] (IRQs 16 17 18 19 20) *11
ACPI: PCI Interrupt Link [LPMU] (IRQs 16 17 18 19 20) *11
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Cannot allocate resource region 7 of bridge 0000:00:0c.0
PCI: Cannot allocate resource region 8 of bridge 0000:00:0c.0
PCI: Cannot allocate resource region 9 of bridge 0000:00:0c.0
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
ACPI: RTC can wake from S4
Time: hpet clocksource has been installed.
pnp: 00:02: iomem range 0xe0000000-0xefffffff could not be reserved
pnp: 00:03: ioport range 0x1000-0x107f has been reserved
pnp: 00:03: ioport range 0x1080-0x10ff has been reserved
pnp: 00:03: ioport range 0x1400-0x147f has been reserved
pnp: 00:03: ioport range 0x1480-0x14ff has been reserved
pnp: 00:03: ioport range 0x1800-0x187f has been reserved
pnp: 00:03: ioport range 0x1880-0x18ff has been reserved
pnp: 00:03: ioport range 0x3040-0x307f has been reserved
pnp: 00:03: ioport range 0x3000-0x303f has been reserved
pnp: 00:0b: iomem range 0xffc00000-0xffffffff could not be reserved
pnp: 00:0b: iomem range 0xfec00000-0xfec00fff could not be reserved
pnp: 00:0b: iomem range 0xfee00000-0xfeefffff could not be reserved
pnp: 00:0b: iomem range 0xfed00000-0xfed00fff has been reserved
PCI: Bridge: 0000:00:08.0
  IO window: disabled.
  MEM window: f2100000-f21fffff
  PREFETCH window: disabled.
PCI: Failed to allocate mem resource #6:20000@e0000000 for 0000:02:00.0
PCI: Bridge: 0000:00:0b.0
  IO window: 4000-4fff
  MEM window: cc000000-ceffffff
  PREFETCH window: d0000000-dfffffff
PCI: Bridge: 0000:00:0c.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:0e.0
  IO window: disabled.
  MEM window: f2000000-f20fffff
  PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:08.0 to 64
PCI: Setting latency timer of device 0000:00:0b.0 to 64
PCI: Setting latency timer of device 0000:00:0c.0 to 64
PCI: Setting latency timer of device 0000:00:0e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 131072 (order: 9, 3145728 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 30160k freed
Simple Boot Flag at 0x36 set to 0x1
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:02:00.0
PCI: Setting latency timer of device 0000:00:0b.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0b.0:pcie00]
Allocate Port Service[0000:00:0b.0:pcie03]
PCI: Setting latency timer of device 0000:00:0c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0c.0:pcie00]
Allocate Port Service[0000:00:0c.0:pcie03]
PCI: Setting latency timer of device 0000:00:0e.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0e.0:pcie00]
Allocate Port Service[0000:00:0e.0:pcie03]
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input0
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 252k freed
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
input: Power Button (FF) as /devices/virtual/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /devices/virtual/input/input3
ACPI: Power Button (CM) [PWRB]
input: Lid Switch as /devices/virtual/input/input4
ACPI: Lid Switch [LID]
input: Sleep Button (CM) as /devices/virtual/input/input5
ACPI: Sleep Button (CM) [SLPB]
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI Exception (processor_core-0818): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0818): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI: Thermal Zone [THRM] (52 C)
input: Video Bus as /devices/virtual/input/input6
ACPI: Video Device [IGPU] (multi-head: yes  rom: no  post: no)
input: Video Bus as /devices/virtual/input/input7
ACPI: Video Device [Z004] (multi-head: yes  rom: no  post: no)
ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 10
ACPI: PCI Interrupt 0000:01:09.0[A] -> Link [LNK1] -> GSI 10 (level, low) -> IRQ 10
firewire_ohci: Added fw-ohci device 0000:01:09.0, OHCI version 1.10
rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
rtc_cmos: probe of 00:07 failed with error -16
ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [LAZA] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:07.0 to 64
hda_codec: Unknown model for ALC268, trying auto-probe from BIOS...
si3054: cannot initialize. EXT MID = 0000
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-MCP67: IDE controller at PCI slot 0000:00:06.0
NFORCE-MCP67: chipset revision 161
NFORCE-MCP67: not 100% native mode: will probe irqs later
NFORCE-MCP67: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE-MCP67: 0000:00:06.0 (rev a1) UDMA133 controller
    ide0: BM-DMA at 0x30c0-0x30c7, BIOS settings: hda:DMA, hdb:pio
Probing IDE interface ide0...
firewire_core: created new fw device fw0 (0 config rom retries, S400)
hda: HL-DT-ST DVDRAM GSA-T20N, ATAPI CD/DVD-ROM drive
hda: selected mode 0x42
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
libata version 2.21 loaded.
ahci 0000:00:09.0: version 2.3
ACPI: PCI Interrupt Link [LSI0] enabled at IRQ 19
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LSI0] -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:09.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl IDE mode
ahci 0000:00:09.0: flags: 64bit sntf led clo pmp pio slum part 
PCI: Setting latency timer of device 0000:00:09.0 to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 cmd 0xffffc20000030100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 19
ata2: SATA max UDMA/133 cmd 0xffffc20000030180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 19
ata3: SATA max UDMA/133 cmd 0xffffc20000030200 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 19
ata4: SATA max UDMA/133 cmd 0xffffc20000030280 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 19
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.
ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 18
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LMAC] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:0a.0 to 64
forcedeth: using HIGHDMA
eth0: forcedeth.c: subsystem: 01025:0127 bound to 0000:00:0a.0
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
wlan: 0.8.4.2 (0.9.3.3)
ath_pci: 0.9.4.5 (0.9.3.3)
ACPI: PCI Interrupt Link [LK3E] enabled at IRQ 17
ACPI: PCI Interrupt 0000:07:00.0[A] -> Link [LK3E] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:07:00.0 to 64
wifi%d: unable to attach hardware: 'Hardware revision not supported' (HAL status 13)
ACPI: PCI interrupt for device 0000:07:00.0 disabled
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 16
ACPI: PCI Interrupt 0000:00:02.1[b] -> Link [LUS2] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: irq 16, io mem 0xf2489000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ACPI: PCI Interrupt Link [Z003] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:04.1[b] -> Link [Z003] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:04.1 to 64
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:04.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:04.1
ehci_hcd 0000:00:04.1: irq 20, io mem 0xf2489400
ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 19
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:02.0: irq 19, io mem 0xf2486000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
ACPI: PCI Interrupt Link [Z002] enabled at IRQ 18
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [Z002] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:04.0 to 64
ohci_hcd 0000:00:04.0: OHCI Host Controller
ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:04.0: irq 18, io mem 0xf2487000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 4 ports detected
usb 3-1: new full speed USB device using ohci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
usb 3-2: new low speed USB device using ohci_hcd and address 3
usb 3-2: configuration #1 chosen from 1 choice
hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
usbcore: registered new interface driver hiddev
input: USB Mouse as /devices/pci0000:00/0000:00:02.0/usb3/3-2/3-2:1.0/input/input8
input: USB HID v1.10 Mouse [USB Mouse] on usb-0000:00:02.0-2
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Initializing USB Mass Storage driver...
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
floppy0: no floppy controllers found
md: linear personality registered for level -1
md: multipath personality registered for level -4
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
xor: automatically using best checksumming function: generic_sse
   generic_sse:  5485.200 MB/sec
xor: using function: generic_sse (5485.200 MB/sec)
async_tx: api initialized (async)
raid6: int64x1   1792 MB/s
raid6: int64x2   2203 MB/s
raid6: int64x4   2248 MB/s
raid6: int64x8   1789 MB/s
raid6: sse2x1    2511 MB/s
raid6: sse2x2    3360 MB/s
raid6: sse2x4    3434 MB/s
raid6: using algorithm sse2x4 (3434 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: raid10 personality registered for level 10
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
scsi 4:0:0:0: Direct-Access     NEWMAN   FLASH !DISK      %z!Y PQ: 0 ANSI: 2
usb-storage: device scan complete
sd 4:0:0:0: [sda] 128544 512-byte hardware sectors (66 MB)
sd 4:0:0:0: [sda] Write Protect is off
sd 4:0:0:0: [sda] Mode Sense: 0b 00 00 08
sd 4:0:0:0: [sda] Assuming drive cache: write through
sd 4:0:0:0: [sda] 128544 512-byte hardware sectors (66 MB)
sd 4:0:0:0: [sda] Write Protect is off
sd 4:0:0:0: [sda] Mode Sense: 0b 00 00 08
sd 4:0:0:0: [sda] Assuming drive cache: write through
 sda: sda1
sd 4:0:0:0: [sda] Attached SCSI removable disk

Arch Linux

#1 2008-01-27 15:33:30

Archlinux_x86_64_0.8.2 can't recognize hard disk on Acer aspire 4520g

#2 2008-02-01 12:34:19

Re: Archlinux_x86_64_0.8.2 can't recognize hard disk on Acer aspire 4520g

#3 2008-02-01 12:55:45

Re: Archlinux_x86_64_0.8.2 can't recognize hard disk on Acer aspire 4520g

#4 2008-02-01 12:58:43

Re: Archlinux_x86_64_0.8.2 can't recognize hard disk on Acer aspire 4520g

#5 2008-02-02 15:42:26

Re: Archlinux_x86_64_0.8.2 can't recognize hard disk on Acer aspire 4520g

#6 2008-02-03 05:14:31

Re: Archlinux_x86_64_0.8.2 can't recognize hard disk on Acer aspire 4520g

#7 2008-02-04 15:45:35

Re: Archlinux_x86_64_0.8.2 can't recognize hard disk on Acer aspire 4520g

Board footer