[SOLVED] Attansic Network Controller is not workig

hoobastank · 2010-08-07 19:02:07

Hi,

I have new an Acer Timelinex 4820T laptop, but network isn't working. I've installed Archlinux 2009.08 x86_64, kernel 2.6.30-ARCH

Here some hints to figure out the problem...

#lspci | grep -i ethernet
01:00.0 Ethernet controller: Attansic Technology Corp. Device 1073 (rev c0)

so i'm using Atheros based ethernet cards

#zgrep -i atl1e /proc/config.gz
CONFIG_ATL1E=m

so it's already built as a module

is it already loaded?

#lsmod | grep -i atl1e
atl1e  39108 0

yes, now i'm trying again to start network

#/etc/rc.d/network restart
Stopping Network FAIL
Starting Network BUSY
dhcpcd: eth0: interface not found or invalid
dhcpcd: time out

#ifconfig -a
lo  Link encap:Local Loopback ..
bla bla..

i have no eth0

is there any idea for this problem?

Last edited by hoobastank (2010-08-09 19:17:16)

.:B:. · 2010-08-07 19:12:45

Did you check dmesg for any possible errors?

hoobastank · 2010-08-07 19:41:57

Yes,

# dmesg | grep -i ethernet
# dmesg | grep -i eth0
# dmesg | grep -i network
Initalizing network drop monitor service
# dmesg | grep -i atl1e
# dmesg | grep -i interface
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
Linux video capture interface: v2.00
usbcore: registered new interface driver uvcvideo

is it meaningful?

.:B:. · 2010-08-07 19:56:06

Not like this no, poste the full dmesg output please.

hoobastank · 2010-08-07 20:23:25

Linux version 2.6.30-ARCH (root@T-POWA-LX) (gcc version 4.4.1 (GCC) ) #1 SMP PREEMPT Fri Jul 31 07:30:28 CEST 2009
Command line: root=/dev/disk/by-uuid/0a714b68-bc83-45ab-90a2-3aa4595aa055 ro
KERNEL supported cpus:
  Intel GenuineIntel
  AMD AuthenticAMD
  Centaur CentaurHauls
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009d000 (usable)
 BIOS-e820: 000000000009d000 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 00000000b3675000 (usable)
 BIOS-e820: 00000000b3675000 - 00000000b36bf000 (reserved)
 BIOS-e820: 00000000b36bf000 - 00000000b374c000 (usable)
 BIOS-e820: 00000000b374c000 - 00000000b37bf000 (ACPI NVS)
 BIOS-e820: 00000000b37bf000 - 00000000b37e3000 (usable)
 BIOS-e820: 00000000b37e3000 - 00000000b37ff000 (ACPI data)
 BIOS-e820: 00000000b37ff000 - 00000000b3800000 (usable)
 BIOS-e820: 00000000b3800000 - 00000000c0000000 (reserved)
 BIOS-e820: 00000000f0000000 - 00000000f8000000 (reserved)
 BIOS-e820: 00000000feb00000 - 00000000feb04000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fed10000 - 00000000fed14000 (reserved)
 BIOS-e820: 00000000fed18000 - 00000000fed1a000 (reserved)
 BIOS-e820: 00000000fed1b000 - 00000000fed20000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
 BIOS-e820: 0000000100000000 - 0000000138000000 (usable)
DMI 2.6 present.
last_pfn = 0x138000 max_arch_pfn = 0x100000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
  00000-9FFFF write-back
  A0000-BFFFF uncachable
  C0000-EFFFF write-through
  F0000-FFFFF write-combining
MTRR variable ranges enabled:
  0 base 000000000 mask F80000000 write-back
  1 base 0FFE00000 mask FFFE00000 write-protect
  2 base 080000000 mask FC0000000 write-back
  3 base 0B8000000 mask FF8000000 uncachable
  4 base 0B4000000 mask FFC000000 uncachable
  5 base 0B3800000 mask FFF800000 uncachable
  6 base 100000000 mask FC0000000 write-back
  7 base 138000000 mask FF8000000 uncachable
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
last_pfn = 0xb3800 max_arch_pfn = 0x100000000
e820 update range: 0000000000001000 - 0000000000006000 (usable) ==> (reserved)
Scanning 1 areas for low memory corruption
modified physical RAM map:
 modified: 0000000000000000 - 0000000000001000 (usable)
 modified: 0000000000001000 - 0000000000006000 (reserved)
 modified: 0000000000006000 - 000000000009d000 (usable)
 modified: 000000000009d000 - 00000000000a0000 (reserved)
 modified: 00000000000e0000 - 0000000000100000 (reserved)
 modified: 0000000000100000 - 00000000b3675000 (usable)
 modified: 00000000b3675000 - 00000000b36bf000 (reserved)
 modified: 00000000b36bf000 - 00000000b374c000 (usable)
 modified: 00000000b374c000 - 00000000b37bf000 (ACPI NVS)
 modified: 00000000b37bf000 - 00000000b37e3000 (usable)
 modified: 00000000b37e3000 - 00000000b37ff000 (ACPI data)
 modified: 00000000b37ff000 - 00000000b3800000 (usable)
 modified: 00000000b3800000 - 00000000c0000000 (reserved)
 modified: 00000000f0000000 - 00000000f8000000 (reserved)
 modified: 00000000feb00000 - 00000000feb04000 (reserved)
 modified: 00000000fec00000 - 00000000fec01000 (reserved)
 modified: 00000000fed10000 - 00000000fed14000 (reserved)
 modified: 00000000fed18000 - 00000000fed1a000 (reserved)
 modified: 00000000fed1b000 - 00000000fed20000 (reserved)
 modified: 00000000fee00000 - 00000000fee01000 (reserved)
 modified: 00000000ffe00000 - 0000000100000000 (reserved)
 modified: 0000000100000000 - 0000000138000000 (usable)
init_memory_mapping: 0000000000000000-00000000b3800000
 0000000000 - 00b3800000 page 2M
kernel direct mapping tables up to b3800000 @ 8000-c000
init_memory_mapping: 0000000100000000-0000000138000000
 0100000000 - 0138000000 page 2M
kernel direct mapping tables up to 138000000 @ a000-10000
RAMDISK: 37f4e000 - 37fefe4c
ACPI: RSDP 00000000000fe020 00024 (v02 ACRSYS)
ACPI: XSDT 00000000b37fe120 00074 (v01 ACRSYS ACRPRDCT 00000001      01000013)
ACPI: FACP 00000000b37fc000 000F4 (v04 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: DSDT 00000000b37ed000 0BB9F (v02 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: FACS 00000000b375f000 00040
ACPI: ASF! 00000000b37fd000 000A5 (v32 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: HPET 00000000b37fb000 00038 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: APIC 00000000b37fa000 0008C (v02 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: MCFG 00000000b37f9000 0003C (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: SLIC 00000000b37ec000 00176 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: BOOT 00000000b37e9000 00028 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: ASPT 00000000b37e5000 00034 (v04 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: WDAT 00000000b37e4000 00224 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: SSDT 00000000b37e3000 009F1 (v01  PmRef    CpuPm 00003000 INTL 20051117)
ACPI: Local APIC address 0xfee00000
(8 early reservations) ==> bootmem [0000000000 - 0138000000]
  #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
  #1 [0000006000 - 0000008000]       TRAMPOLINE ==> [0000006000 - 0000008000]
  #2 [0000200000 - 000082d0d0]    TEXT DATA BSS ==> [0000200000 - 000082d0d0]
  #3 [0037f4e000 - 0037fefe4c]          RAMDISK ==> [0037f4e000 - 0037fefe4c]
  #4 [000009d000 - 0000100000]    BIOS reserved ==> [000009d000 - 0000100000]
  #5 [000082e000 - 000082e2fa]              BRK ==> [000082e000 - 000082e2fa]
  #6 [0000008000 - 000000a000]          PGTABLE ==> [0000008000 - 000000a000]
  #7 [000000a000 - 000000b000]          PGTABLE ==> [000000a000 - 000000b000]
 [ffffe20000000000-ffffe200045fffff] PMD -> [ffff880028200000-ffff88002c7fffff] on node 0
Zone PFN ranges:
  DMA      0x00000000 -> 0x00001000
  DMA32    0x00001000 -> 0x00100000
  Normal   0x00100000 -> 0x00138000
Movable zone start PFN for each node
early_node_map[7] active PFN ranges
    0: 0x00000000 -> 0x00000001
    0: 0x00000006 -> 0x0000009d
    0: 0x00000100 -> 0x000b3675
    0: 0x000b36bf -> 0x000b374c
    0: 0x000b37bf -> 0x000b37e3
    0: 0x000b37ff -> 0x000b3800
    0: 0x00100000 -> 0x00138000
On node 0 totalpages: 964287
  DMA zone: 56 pages used for memmap
  DMA zone: 1686 pages reserved
  DMA zone: 2250 pages, LIFO batch:0
  DMA32 zone: 14280 pages used for memmap
  DMA32 zone: 716639 pages, LIFO batch:31
  Normal zone: 3136 pages used for memmap
  Normal zone: 226240 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x05] enabled)
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)
ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 0, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a201 base: 0xfed00000
SMP: Allowing 8 CPUs, 4 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 0000000000001000 - 0000000000006000
PM: Registered nosave memory: 000000000009d000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
PM: Registered nosave memory: 00000000b3675000 - 00000000b36bf000
PM: Registered nosave memory: 00000000b374c000 - 00000000b37bf000
PM: Registered nosave memory: 00000000b37e3000 - 00000000b37ff000
PM: Registered nosave memory: 00000000b3800000 - 00000000c0000000
PM: Registered nosave memory: 00000000c0000000 - 00000000f0000000
PM: Registered nosave memory: 00000000f0000000 - 00000000f8000000
PM: Registered nosave memory: 00000000f8000000 - 00000000feb00000
PM: Registered nosave memory: 00000000feb00000 - 00000000feb04000
PM: Registered nosave memory: 00000000feb04000 - 00000000fec00000
PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000
PM: Registered nosave memory: 00000000fec01000 - 00000000fed10000
PM: Registered nosave memory: 00000000fed10000 - 00000000fed14000
PM: Registered nosave memory: 00000000fed14000 - 00000000fed18000
PM: Registered nosave memory: 00000000fed18000 - 00000000fed1a000
PM: Registered nosave memory: 00000000fed1a000 - 00000000fed1b000
PM: Registered nosave memory: 00000000fed1b000 - 00000000fed20000
PM: Registered nosave memory: 00000000fed20000 - 00000000fee00000
PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
PM: Registered nosave memory: 00000000fee01000 - 00000000ffe00000
PM: Registered nosave memory: 00000000ffe00000 - 0000000100000000
Allocating PCI resources starting at c4000000 (gap: c0000000:30000000)
NR_CPUS:16 nr_cpumask_bits:16 nr_cpu_ids:8 nr_node_ids:1
PERCPU: Embedded 25 pages at ffff880028023000, static data 72352 bytes
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 945129
Kernel command line: root=/dev/disk/by-uuid/0a714b68-bc83-45ab-90a2-3aa4595aa055 ro
Initializing CPU#0
NR_IRQS:768
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000
Fast TSC calibration using PIT
Detected 2128.487 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Checking aperture...
No AGP bridge found
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Placing 64MB software IO TLB between ffff880020000000 - ffff880024000000
software IO TLB at phys 0x20000000 - 0x24000000
Memory: 3704436k/5111808k available (3409k kernel code, 1254660k absent, 151788k reserved, 1239k data, 464k init)
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
hpet clockevent registered
HPET: 8 timers in total, 6 timers will be used for per-cpu timer
Calibrating delay loop (skipped), value calculated using timer frequency.. 4258.34 BogoMIPS (lpj=7094956)
Security Framework initialized
Mount-cache hash table entries: 256
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 3072K
CPU0: Thermal monitoring enabled (TM1)
CPU 0 MCA banks CMCI:2 CMCI:3 CMCI:5 CMCI:6
using mwait in idle threads.
ACPI: Core revision 20090320
Setting APIC routing to flat
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM) i3 CPU       M 330  @ 2.13GHz stepping 02
APIC calibration not consistent with PM-Timer: 449ms instead of 100ms
APIC delta adjusted to PM-Timer: 831392 (3741252)
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4258.10 BogoMIPS (lpj=7094570)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 3072K
CPU1: Thermal monitoring enabled (TM1)
CPU 1 MCA banks SHD:2 SHD:3 SHD:5 SHD:6
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: Intel(R) Core(TM) i3 CPU       M 330  @ 2.13GHz stepping 02
Skipping synchronization checks as TSC is reliable.
Booting processor 2 APIC 0x4 ip 0x6000
Initializing CPU#2
Calibrating delay using timer specific routine.. 4258.11 BogoMIPS (lpj=7094589)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 2
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 3072K
CPU2: Thermal monitoring enabled (TM1)
CPU 2 MCA banks CMCI:2 CMCI:3 CMCI:5 SHD:6
x86 PAT enabled: cpu 2, old 0x7040600070406, new 0x7010600070106
CPU2: Intel(R) Core(TM) i3 CPU       M 330  @ 2.13GHz stepping 02
Skipping synchronization checks as TSC is reliable.
Booting processor 3 APIC 0x5 ip 0x6000
Initializing CPU#3
Calibrating delay using timer specific routine.. 4258.11 BogoMIPS (lpj=7094587)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 2
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 3072K
CPU3: Thermal monitoring enabled (TM1)
CPU 3 MCA banks SHD:2 SHD:3 SHD:5 SHD:6
x86 PAT enabled: cpu 3, old 0x7040600070406, new 0x7010600070106
CPU3: Intel(R) Core(TM) i3 CPU       M 330  @ 2.13GHz stepping 02
Skipping synchronization checks as TSC is reliable.
Brought up 4 CPUs
Total of 4 processors activated (17034.68 BogoMIPS).
CPU0 attaching sched-domain:
 domain 0: span 0-1 level SIBLING
  groups: 0 1
  domain 1: span 0-3 level MC
   groups: 0-1 2-3
CPU1 attaching sched-domain:
 domain 0: span 0-1 level SIBLING
  groups: 1 0
  domain 1: span 0-3 level MC
   groups: 0-1 2-3
CPU2 attaching sched-domain:
 domain 0: span 2-3 level SIBLING
  groups: 2 3
  domain 1: span 0-3 level MC
   groups: 2-3 0-1
CPU3 attaching sched-domain:
 domain 0: span 2-3 level SIBLING
  groups: 3 2
  domain 1: span 0-3 level MC
   groups: 2-3 0-1
net_namespace: 1888 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type pci registered
PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 127
PCI: MCFG area at f0000000 reserved in E820
PCI: Using MMCONFIG at f0000000 - f7ffffff
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: BIOS _OSI(Linux) query ignored
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in interrupt mode
ACPI: No dock devices found.
_OSC invalid UUID
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:02.0: reg 10 64bit mmio: [0xd0000000-0xd03fffff]
pci 0000:00:02.0: reg 18 64bit mmio: [0xc0000000-0xcfffffff]
pci 0000:00:02.0: reg 20 io port: [0x3050-0x3057]
pci 0000:00:16.0: reg 10 64bit mmio: [0xd4406100-0xd440610f]
pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
pci 0000:00:16.0: PME# disabled
pci 0000:00:1a.0: reg 10 32bit mmio: [0xd4405c00-0xd4405fff]
pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.0: PME# disabled
pci 0000:00:1b.0: reg 10 64bit mmio: [0xd4400000-0xd4403fff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.5: PME# disabled
pci 0000:00:1d.0: reg 10 32bit mmio: [0xd4405800-0xd4405bff]
pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.0: PME# disabled
pci 0000:00:1f.2: reg 10 io port: [0x3048-0x304f]
pci 0000:00:1f.2: reg 14 io port: [0x305c-0x305f]
pci 0000:00:1f.2: reg 18 io port: [0x3040-0x3047]
pci 0000:00:1f.2: reg 1c io port: [0x3058-0x305b]
pci 0000:00:1f.2: reg 20 io port: [0x3020-0x303f]
pci 0000:00:1f.2: reg 24 32bit mmio: [0xd4405000-0xd44057ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1f.3: reg 10 64bit mmio: [0xd4406000-0xd44060ff]
pci 0000:00:1f.3: reg 20 io port: [0x3000-0x301f]
pci 0000:00:1f.6: reg 10 64bit mmio: [0xd4404000-0xd4404fff]
pci 0000:01:00.0: reg 10 64bit mmio: [0xd3400000-0xd343ffff]
pci 0000:01:00.0: reg 18 io port: [0x2000-0x207f]
pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:01:00.0: PME# disabled
pci 0000:00:1c.0: bridge io port: [0x2000-0x2fff]
pci 0000:00:1c.0: bridge 32bit mmio: [0xd3400000-0xd43fffff]
pci 0000:00:1c.0: bridge 64bit mmio pref: [0xd0400000-0xd13fffff]
pci 0000:02:00.0: reg 10 64bit mmio: [0xd2400000-0xd2403fff]
pci 0000:02:00.0: supports D1 D2
pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
pci 0000:02:00.0: PME# disabled
pci 0000:00:1c.5: bridge io port: [0x1000-0x1fff]
pci 0000:00:1c.5: bridge 32bit mmio: [0xd2400000-0xd33fffff]
pci 0000:00:1c.5: bridge 64bit mmio pref: [0xd1400000-0xd23fffff]
pci 0000:00:1e.0: transparent bridge
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
_OSC invalid UUID
ACPI: PCI Root Bridge [CPBG] (0000:7f)
pci_bus 0000:7f: on NUMA node 0
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 *7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 *5 6 7 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 *7 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15)
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
hpet: hpet2 irq 24 for MSI
hpet: hpet3 irq 25 for MSI
hpet: hpet4 irq 26 for MSI
hpet: hpet5 irq 27 for MSI
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 2
Switched to high resolution mode on CPU 3
Switched to high resolution mode on CPU 1
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:05: io resource (0x164e-0x164f) overlaps 0000:00:1c.5 BAR 13 (0x1000-0x1fff), disabling
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
system 00:05: ioport range 0x680-0x69f has been reserved
system 00:05: ioport range 0x800-0x80f has been reserved
system 00:05: ioport range 0xffff-0xffff has been reserved
system 00:05: ioport range 0xffff-0xffff has been reserved
system 00:05: ioport range 0x400-0x47f has been reserved
system 00:05: ioport range 0x500-0x57f has been reserved
system 00:09: iomem range 0xfed1c000-0xfed1ffff has been reserved
system 00:09: iomem range 0xfed10000-0xfed13fff has been reserved
system 00:09: iomem range 0xfed18000-0xfed18fff has been reserved
system 00:09: iomem range 0xfed19000-0xfed19fff has been reserved
system 00:09: iomem range 0xf0000000-0xf1ffffff has been reserved
system 00:09: iomem range 0xfed20000-0xfed3ffff has been reserved
system 00:09: iomem range 0xfed45000-0xfed8ffff has been reserved
system 00:09: iomem range 0xff000000-0xffffffff could not be reserved
system 00:09: iomem range 0xfee00000-0xfeefffff could not be reserved
system 00:09: iomem range 0xd4500000-0xd4500fff has been reserved
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:01
pci 0000:00:1c.0:   IO window: 0x2000-0x2fff
pci 0000:00:1c.0:   MEM window: 0xd3400000-0xd43fffff
pci 0000:00:1c.0:   PREFETCH window: 0x000000d0400000-0x000000d13fffff
pci 0000:00:1c.5: PCI bridge, secondary bus 0000:02
pci 0000:00:1c.5:   IO window: 0x1000-0x1fff
pci 0000:00:1c.5:   MEM window: 0xd2400000-0xd33fffff
pci 0000:00:1c.5:   PREFETCH window: 0x000000d1400000-0x000000d23fffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:03
pci 0000:00:1e.0:   IO window: disabled
pci 0000:00:1e.0:   MEM window: disabled
pci 0000:00:1e.0:   PREFETCH window: disabled
pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.5: PCI INT B -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.5: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
pci_bus 0000:01: resource 0 io:  [0x2000-0x2fff]
pci_bus 0000:01: resource 1 mem: [0xd3400000-0xd43fffff]
pci_bus 0000:01: resource 2 pref mem [0xd0400000-0xd13fffff]
pci_bus 0000:02: resource 0 io:  [0x1000-0x1fff]
pci_bus 0000:02: resource 1 mem: [0xd2400000-0xd33fffff]
pci_bus 0000:02: resource 2 pref mem [0xd1400000-0xd23fffff]
pci_bus 0000:03: resource 3 io:  [0x00-0xffff]
pci_bus 0000:03: resource 4 mem: [0x000000-0xffffffffffffffff]
pci_bus 0000:7f: resource 0 io:  [0x00-0xffff]
pci_bus 0000:7f: resource 1 mem: [0x000000-0xffffffffffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Unpacking initramfs...
Freeing initrd memory: 647k freed
Simple Boot Flag at 0x44 set to 0x1
Scanning for low memory corruption every 60 seconds
audit: initializing netlink socket (disabled)
type=2000 audit(1281216334.486:1): initialized
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
msgmni has been set to 7238
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:02.0: Boot video device
pcieport-driver 0000:00:1c.0: irq 30 for MSI/MSI-X
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.5: irq 31 for MSI/MSI-X
pcieport-driver 0000:00:1c.5: setting latency timer to 64
Linux agpgart interface v0.103
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
input: Macintosh mouse button emulation as /devices/virtual/input/input0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
registered taskstats version 1
Initalizing network drop monitor service
Freeing unused kernel memory: 464k freed
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
SCSI subsystem initialized
libata version 3.00 loaded.
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:1f.2: irq 32 for MSI/MSI-X
ahci: SSS flag set, parallel bus scan disabled
ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 4 ports 3 Gbps 0x3 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ems 
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m2048@0xd4405000 port 0xd4405100 irq 32
ata2: SATA max UDMA/133 irq_stat 0x00000040, connection status changed irq 32
ata3: DUMMY
ata4: DUMMY
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-8: Hitachi HTS545032B9A300, PB3OC60F, max UDMA/133
ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access     ATA      Hitachi HTS54503 PB3O PQ: 0 ANSI: 5
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ACPI _SDD failed (AE 0x5)
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ACPI _SDD failed (AE 0x5)
ata2.00: ACPI: failed the second time, disabled
ata2.00: ATAPI: HL-DT-ST DVDRAM GU10N, AP04, max UDMA/133, ATAPI AN
ata2.00: configured for UDMA/133
scsi 1:0:0:0: CD-ROM            HL-DT-ST DVDRAM GU10N     AP04 PQ: 0 ANSI: 5
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda:<4>Driver 'sr' needs updating - please use bus_type methods
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
 sda1 sda2 sda3 < sda5 sda6 sda7 >
sd 0:0:0:0: [sda] Attached SCSI disk
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with writeback data mode.
rtc_cmos 00:06: RTC can wake from S4
rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, y3k, 242 bytes nvram, hpet irqs
udev: starting version 141
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
ACPI: Power Button [PWRF]
input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0A08:00/PNP0C0C:00/input/input3
ACPI: Power Button [PWRB]
input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0A08:00/PNP0C0D:00/input/input4
ACPI: Lid Switch [LID0]
input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0A08:00/PNP0C0E:00/input/input5
ACPI: Sleep Button [SLPB]
ACPI: Battery Slot [BAT1] (battery present)
ACPI: SSDT 00000000b3691c18 003AE (v01  PmRef  Cpu0Ist 00003000 INTL 20051117)
ACPI: SSDT 00000000b368f018 00891 (v01  PmRef  Cpu0Cst 00003001 INTL 20051117)
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-3 state
ACPI: CPU0 (power states: C1[C1] C2[C3])
processor ACPI_CPU:00: registered as cooling_device0
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: SSDT 00000000b3690a98 00303 (v01  PmRef    ApIst 00003000 INTL 20051117)
ACPI: SSDT 00000000b368ed98 00119 (v01  PmRef    ApCst 00003000 INTL 20051117)
ACPI: CPU1 (power states: C1[C1] C2[C3])
processor ACPI_CPU:01: registered as cooling_device1
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: CPU2 (power states: C1[C1] C2[C3])
processor ACPI_CPU:02: registered as cooling_device2
ACPI: Processor [CPU2] (supports 8 throttling states)
ACPI: CPU3 (power states: C1[C1] C2[C3])
processor ACPI_CPU:03: registered as cooling_device3
ACPI: Processor [CPU3] (supports 8 throttling states)
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (40 C)
input: PC Speaker as /devices/platform/pcspkr/input/input6
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ACPI: AC Adapter [ACAD] (on-line)
ACPI: WMI: Mapper loaded
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ehci_hcd 0000:00:1a.0: setting latency timer to 64
ehci_hcd 0000:00:1a.0: EHCI Host Controller
ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.0: debug port 2
ehci_hcd 0000:00:1a.0: cache line size of 32 is not supported
ehci_hcd 0000:00:1a.0: irq 16, io mem 0xd4405c00
ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.0: setting latency timer to 64
ehci_hcd 0000:00:1d.0: EHCI Host Controller
ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.0: debug port 2
ehci_hcd 0000:00:1d.0: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.0: irq 23, io mem 0xd4405800
ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
i801_smbus 0000:00:1f.3: PCI INT C -> GSI 19 (level, low) -> IRQ 19
usb 1-1: new high speed USB device using ehci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 6 ports detected
usb 2-1: new high speed USB device using ehci_hcd and address 2
Synaptics Touchpad, model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04731/0xa44000
acer-wmi: Acer Laptop ACPI-WMI Extras
acer-wmi: Brightness must be controlled by generic video driver
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input7
HDA Intel 0000:00:1b.0: enabling device (0000 -> 0002)
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
HDA Intel 0000:00:1b.0: setting latency timer to 64
usb 2-1: configuration #1 chosen from 1 choice
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 8 ports detected
hda_codec: Unknown model for ALC269, trying auto-probe from BIOS...
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input8
usb 1-1.1: new high speed USB device using ehci_hcd and address 3
usb 1-1.1: configuration #1 chosen from 1 choice
Linux video capture interface: v2.00
uvcvideo: Found UVC 1.00 device 1.3M WebCam (064e:a219)
input: 1.3M WebCam as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.1/1-1.1:1.0/input/input9
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
EXT3 FS on sda6, internal journal
Adding 2152668k swap on /dev/sda7.  Priority:-1 extents:1 across:2152668k 
usb 2-1.4: new high speed USB device using ehci_hcd and address 3
usb 2-1.4: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
scsi 4:0:0:0: Direct-Access              USB DISK 2.0     PMAP PQ: 0 ANSI: 0 CCS
sd 4:0:0:0: Attached scsi generic sg2 type 0
sd 4:0:0:0: [sdb] 7829504 512-byte hardware sectors: (4.00 GB/3.73 GiB)
sd 4:0:0:0: [sdb] Write Protect is off
sd 4:0:0:0: [sdb] Mode Sense: 23 00 00 00
sd 4:0:0:0: [sdb] Assuming drive cache: write through
usb-storage: device scan complete
sd 4:0:0:0: [sdb] Assuming drive cache: write through
 sdb: sdb1
sd 4:0:0:0: [sdb] Attached SCSI removable disk

hoobastank · 2010-08-08 14:58:55

it'll be very bad if i cant over come this problem... I've been using GNU/Linux for years and since last year I used to use Archlinux

.:B:. · 2010-08-08 15:01:43

I'm checking your dmesg output. You should really update your installation before we can reliably diagnose your problem. Arch is at kernel 2.6.34 now... Can you update the system using wireless?

You should use the latest installation image, the one you used is a bit outdated.

http://www.archlinux.org/download/

If you read this topic, it appears the newer kernel should fix your problem. 2010.05 has 2.6.33.4 which should have support for your NIC. A bit of googling would have given you that solution as well .

Commit that adds support for your card: http://git.kernel.org/?p=linux/kernel/g … 578393cfe0

hoobastank · 2010-08-08 16:21:12

i've already tried Archlinux 2010.05 but i didnt work too. New version of vi editor is really weird and graphic driver is unstable but I still continued with the installation and network again was down. There is no interface like wlan0 or eth0 so i cant download any package to fix it. Everything must be done offline.

#lshw
description: Ethernet controller
product: AR8151 v1.0 Gigabit Ethernet
vendor: Atheros Communications

I think i need AR8151 driver so i'll try the solution which is given at below link.
https://bbs.archlinux.org/viewtopic.php?id=101481
http://rhythmcloud.blogspot.com/2010/07 … gabit.html

hokasch · 2010-08-08 16:28:13

Maybe compat-wireless is an easy way to get your network working, if support was added on later kernels.

.:B:. · 2010-08-08 16:29:30

I would stick with 2010.05 either way, then we can start troubleshooting from there. Either way, you'll have to run an upgrade at some point, and you stand a better chance with a newer kernel than with an old one. 2.6.30 is two years old.

Could you paste lspci -n output for your NIC? It should print 1969:1073.

The topic you link to suggests you'd need 2.6.34 or higher, and 2.6.34.2 is in the repos.

Mektub · 2010-08-08 17:22:43

hoobastank,

There is no interface like wlan0 or eth0 so i cant download any package to fix it. Everything must be done offline.

I had a similar problem with an ASUS PC N61JQ-JX001V with an Attansic Tech Device 1063 (rev 03) after installing Archlinux 2009.08 (i686).

After that the eth0 disappeared and the only way to recover it was to take out the power + battery (!) from the laptop for some
seconds.

I know its weird, but it is reported on the web, only I can't find it anymore.

Mektub

hoobastank · 2010-08-08 21:53:42

.:B:. wrote:

Could you paste lspci -n output for your NIC? It should print 1969:1073.
The topic you link to suggests you'd need 2.6.34 or higher, and 2.6.34.2 is in the repos.

I've just installed 2010.05 x86_64 but you know it includes Kernel: 2.6.33.4

#uname -a
Linux archlinuxtr 2.6.33-ARCH #1 SMP PREEMPT Thu May 13 11:32:37 CEST 2010 x86_64 Intel(R) Core(TM) i3 CPU M 330 @ 2.13GHz GenuineIntel GNU/Linux

#lspci -n
00:00.0 0600: 8086:0044 (rev 12)
00:02.0 0300: 8086:0046 (rev 12)
00:16.0 0780: 8086:3b64 (rev 06)
00:1a.0 0c03: 8086:3b3c (rev 05)
00:1b.0 0403: 8086:3b56 (rev 05)
00:1c.0 0604: 8086:3b42 (rev 05)
00:1c.5 0604: 8086:3b4c (rev 05)
00:1d.0 0c03: 8086:3b34 (rev 05)
00:1e.0 0604: 8086:2448 (rev a5)
00:1f.0 0601: 8086:3b09 (rev 05)
00:1f.2 0106: 8086:3b29 (rev 05)
00:1f.3 0c05: 8086:3b30 (rev 05)
00:1f.6 1180: 8086:3b32 (rev 05)
01:00.0 0200: 1969:1073 (rev c0)
02:00.0 0280: 14e4:4357 (rev 01)
7f:00.0 0600: 8086:2c62 (rev 02)
7f:00.1 0600: 8086:2d01 (rev 02)
7f:02.0 0600: 8086:2d10 (rev 02)
7f:02.1 0600: 8086:2d11 (rev 02)
7f:02.2 0600: 8086:2d12 (rev 02)
7f:02.3 0600: 8086:2d13 (rev 02)

I've tired to install kernel 2.6.34.2 to port modified driver but it gives me some error about dependencies linux-firmware etc. Years ago, once i had installed a software and all of it's dependencies step by step... I was a newbie at that time so I was very patient

hokasch · 2010-08-09 10:50:27

Just install linux-firmware as well? There should not be many more dependencies to follow. Or boot the newest archboot image (unofficial, 2,6.34.1) to reinstall or update from a chroot, or get compat-wireles, or...

hoobastank · 2010-08-09 19:15:46

hokasch wrote:

Just install linux-firmware as well? There should not be many more dependencies to follow. Or boot the newest archboot image (unofficial, 2,6.34.1) to reinstall or update from a chroot, or get compat-wireles, or...

Yes you are right.. I've just installed 2010.07 which has kernel 2.6.34.1 and surprisingly it installed the correct module atl1c for Attansic Device 1073. In the former version of Archlinux, 2010.05, it installed atl1e module as a default. in fact I changed it to atl1c but did not work and again there was no ethernet interface eth0. There is something wrong with it, and i think this is a good puzzle to learn something but i dont have too much time so i choose easy way to solve.

Thank you very much.

The problem is SOLVED..

Last edited by hoobastank (2010-08-09 19:18:33)

Arch Linux

#1 2010-08-07 19:02:07

[SOLVED] Attansic Network Controller is not workig

#2 2010-08-07 19:12:45

Re: [SOLVED] Attansic Network Controller is not workig

#3 2010-08-07 19:41:57

Re: [SOLVED] Attansic Network Controller is not workig

#4 2010-08-07 19:56:06

Re: [SOLVED] Attansic Network Controller is not workig

#5 2010-08-07 20:23:25

Re: [SOLVED] Attansic Network Controller is not workig

#6 2010-08-08 14:58:55

Re: [SOLVED] Attansic Network Controller is not workig

#7 2010-08-08 15:01:43

Re: [SOLVED] Attansic Network Controller is not workig

#8 2010-08-08 16:21:12

Re: [SOLVED] Attansic Network Controller is not workig

#9 2010-08-08 16:28:13

Re: [SOLVED] Attansic Network Controller is not workig

#10 2010-08-08 16:29:30

Re: [SOLVED] Attansic Network Controller is not workig

#11 2010-08-08 17:22:43

Re: [SOLVED] Attansic Network Controller is not workig

#12 2010-08-08 21:53:42

Re: [SOLVED] Attansic Network Controller is not workig

#13 2010-08-09 10:50:27

Re: [SOLVED] Attansic Network Controller is not workig

#14 2010-08-09 19:15:46

Re: [SOLVED] Attansic Network Controller is not workig

Board footer