You are not logged in.
Hello everyone,
I am using ArchLinux on a HP dm1-3100ev (aka dm1z). This little machine is equipped with an 80GB Intel X25-M SSD (2nd gen) and boots and runs nice and fast.
However, I just noticed a curious issue, where the SATA interface takes 5.3 seconds to appear. According to dmesg:
[ 1.510296] Switching to clocksource tsc
[ 6.856991] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 6.857578] ata1.00: ATA-7: INTEL SSDSA2M080G2GC, 2CV102HD, max UDMA/133
[ 6.857585] ata1.00: 156301488 sectors, multi 1: LBA48 NCQ (depth 31/32)
[ 6.858264] ata1.00: configured for UDMA/133
[ 6.858756] scsi 0:0:0:0: Direct-Access ATA INTEL SSDSA2M080 2CV1 PQ: 0 ANSI: 5
[ 6.871132] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 6.871271] sd 0:0:0:0: [sda] Write Protect is off
[ 6.871276] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 6.871320] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 6.872158] sda: sda1
[ 6.873464] sd 0:0:0:0: [sda] Attached SCSI disk
This is on linux 2.6.39. Anyone have any ideas why this is and how I can reduce this delay? This is by far the slowest part of the boot sequence right now!
Full dmesg log below:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.39-ARCH (tobias@T-POWA-LX) (gcc version 4.6.0 20110603 (prerelease) (GCC) ) #1 SMP PREEMPT Mon Jun 6 22:37:55 CEST 2011
[ 0.000000] Command line: root=/dev/disk/by-uuid/3e8701ef-e777-4352-a42c-83dd9f68240a ro nomodeset quiet
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000dfa3f000 (usable)
[ 0.000000] BIOS-e820: 00000000dfa3f000 - 00000000dfabf000 (reserved)
[ 0.000000] BIOS-e820: 00000000dfabf000 - 00000000dfebf000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000dfebf000 - 00000000dfef6000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000dfef6000 - 00000000dff00000 (usable)
[ 0.000000] BIOS-e820: 00000000dff00000 - 00000000e0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec10000 - 00000000fec11000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000187000000 (usable)
[ 0.000000] BIOS-e820: 0000000187000000 - 000000019f000000 (reserved)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI 2.7 present.
[ 0.000000] DMI: Hewlett-Packard HP Pavilion dm1 Notebook PC /1611, BIOS F.12 04/26/2011
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] No AGP bridge found
[ 0.000000] last_pfn = 0x187000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-FFFFF write-through
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 080000000 mask FC0000000 write-back
[ 0.000000] 2 base 0C0000000 mask FE0000000 write-back
[ 0.000000] 3 base 0DFEBD000 mask FFFFFF000 uncachable
[ 0.000000] 4 base 0FFE00000 mask FFFE00000 write-protect
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] TOM2: 000000019f000000 aka 6640M
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] last_pfn = 0xdff00 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [ffff8800000fe1b0] fe1b0
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] Base memory trampoline at [ffff88000009a000] 9a000 size 20480
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] init_memory_mapping: 0000000000000000-00000000dff00000
[ 0.000000] 0000000000 - 00c0000000 page 1G
[ 0.000000] 00c0000000 - 00dfe00000 page 2M
[ 0.000000] 00dfe00000 - 00dff00000 page 4k
[ 0.000000] kernel direct mapping tables up to dff00000 @ dfefd000-dff00000
[ 0.000000] init_memory_mapping: 0000000100000000-0000000187000000
[ 0.000000] 0100000000 - 0180000000 page 1G
[ 0.000000] 0180000000 - 0187000000 page 2M
[ 0.000000] kernel direct mapping tables up to 187000000 @ 186ffe000-187000000
[ 0.000000] RAMDISK: 37e47000 - 37ff0000
[ 0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 HPQOEM)
[ 0.000000] ACPI: XSDT 00000000dfef5120 00064 (v01 HPQOEM SLIC-MPC 00000003 01000013)
[ 0.000000] ACPI: FACP 00000000dfef4000 000F4 (v04 HPQOEM SLIC-MPC 00000003 ACPI 00040000)
[ 0.000000] ACPI: DSDT 00000000dfee7000 0972F (v01 HP INSYDE F0000000 ACPI 00040000)
[ 0.000000] ACPI: FACS 00000000dfc96000 00040
[ 0.000000] ACPI: HPET 00000000dfef3000 00038 (v01 HP INSYDE 00000001 ACPI 00040000)
[ 0.000000] ACPI: APIC 00000000dfef2000 00084 (v02 HP INSYDE 00000001 ACPI 00040000)
[ 0.000000] ACPI: MCFG 00000000dfef1000 0003C (v01 HP INSYDE 00000001 ACPI 00040000)
[ 0.000000] ACPI: BOOT 00000000dfee6000 00028 (v01 HP INSYDE 00000001 ACPI 00040000)
[ 0.000000] ACPI: SLIC 00000000dfee5000 00176 (v01 HPQOEM SLIC-MPC 00000001 ACPI 00040000)
[ 0.000000] ACPI: SSDT 00000000dfee4000 003DE (v01 HP INSYDE 00000001 AMD 00000001)
[ 0.000000] ACPI: SSDT 00000000dfee2000 012FA (v02 HP INSYDE 00000001 MSFT 04000000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-0000000187000000
[ 0.000000] NUMA: Using 63 for the hash shift.
[ 0.000000] Initmem setup node 0 0000000000000000-0000000187000000
[ 0.000000] NODE_DATA [0000000186ff9000 - 0000000186ffdfff]
[ 0.000000] [ffffea0000000000-ffffea00055fffff] PMD -> [ffff880180c00000-ffff880185bfffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00187000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[4] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x000dfa3f
[ 0.000000] 0: 0x000dfef6 -> 0x000dff00
[ 0.000000] 0: 0x00100000 -> 0x00187000
[ 0.000000] On node 0 totalpages: 1468888
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 5 pages reserved
[ 0.000000] DMA zone: 3922 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 897665 pages, LIFO batch:31
[ 0.000000] Normal zone: 7560 pages used for memmap
[ 0.000000] Normal zone: 545400 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 33, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x43538210 base: 0xfed00000
[ 0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 00000000dfa3f000 - 00000000dfabf000
[ 0.000000] PM: Registered nosave memory: 00000000dfabf000 - 00000000dfebf000
[ 0.000000] PM: Registered nosave memory: 00000000dfebf000 - 00000000dfef6000
[ 0.000000] PM: Registered nosave memory: 00000000dff00000 - 00000000e0000000
[ 0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000f8000000
[ 0.000000] PM: Registered nosave memory: 00000000f8000000 - 00000000fc000000
[ 0.000000] PM: Registered nosave memory: 00000000fc000000 - 00000000fec00000
[ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000
[ 0.000000] PM: Registered nosave memory: 00000000fec01000 - 00000000fec10000
[ 0.000000] PM: Registered nosave memory: 00000000fec10000 - 00000000fec11000
[ 0.000000] PM: Registered nosave memory: 00000000fec11000 - 00000000fee00000
[ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[ 0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ffe00000
[ 0.000000] PM: Registered nosave memory: 00000000ffe00000 - 0000000100000000
[ 0.000000] Allocating PCI resources starting at e0000000 (gap: e0000000:18000000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff880186c00000 s83136 r8192 d23360 u524288
[ 0.000000] pcpu-alloc: s83136 r8192 d23360 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1446987
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: root=/dev/disk/by-uuid/3e8701ef-e777-4352-a42c-83dd9f68240a ro nomodeset quiet
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 5715728k/6406144k available (4022k kernel code, 530592k absent, 159824k reserved, 3332k data, 724k init)
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptable hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:2304
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 47185920 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1596.101 MHz processor.
[ 0.003340] Calibrating delay loop (skipped), value calculated using timer frequency.. 3193.21 BogoMIPS (lpj=5320336)
[ 0.003347] pid_max: default: 32768 minimum: 301
[ 0.003562] Security Framework initialized
[ 0.003572] AppArmor: AppArmor disabled by boot time parameter
[ 0.005092] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.012089] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.014996] Mount-cache hash table entries: 256
[ 0.015789] Initializing cgroup subsys ns
[ 0.015797] ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup.
[ 0.015802] Initializing cgroup subsys cpuacct
[ 0.015866] Initializing cgroup subsys memory
[ 0.015901] Initializing cgroup subsys devices
[ 0.015905] Initializing cgroup subsys freezer
[ 0.015908] Initializing cgroup subsys net_cls
[ 0.015911] Initializing cgroup subsys blkio
[ 0.016009] tseg: 00dff00000
[ 0.016014] CPU: Physical Processor ID: 0
[ 0.016016] CPU: Processor Core ID: 0
[ 0.016019] mce: CPU supports 6 MCE banks
[ 0.018003] ACPI: Core revision 20110316
[ 0.026713] ftrace: allocating 15966 entries in 63 pages
[ 0.030133] Setting APIC routing to flat
[ 0.030496] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.064116] CPU0: AMD E-350 Processor stepping 00
[ 0.066663] Performance Events: AMD PMU driver.
[ 0.066663] ... version: 0
[ 0.066663] ... bit width: 48
[ 0.066663] ... generic registers: 4
[ 0.066663] ... value mask: 0000ffffffffffff
[ 0.066663] ... max period: 00007fffffffffff
[ 0.066663] ... fixed-purpose events: 0
[ 0.066663] ... event mask: 000000000000000f
[ 0.083498] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.110105] Booting Node 0, Processors #1
[ 0.110114] smpboot cpu 1: start_ip = 9a000
[ 0.206704] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.213374] Brought up 2 CPUs
[ 0.213387] Total of 2 processors activated (6386.16 BogoMIPS).
[ 0.213856] devtmpfs: initialized
[ 0.217207] PM: Registering ACPI NVS region at dfabf000 (4194304 bytes)
[ 0.218611] print_constraints: dummy:
[ 0.218770] NET: Registered protocol family 16
[ 0.219087] Extended Config Space enabled on 0 nodes
[ 0.219123] ACPI: bus type pci registered
[ 0.220109] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[ 0.220115] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[ 0.230714] PCI: Using configuration type 1 for base access
[ 0.231511] bio: create slab <bio-0> at 0
[ 0.234922] ACPI: EC: Look up EC in DSDT
[ 0.237245] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.241929] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.253590] ACPI: Interpreter enabled
[ 0.253602] ACPI: (supports S0 S3 S4 S5)
[ 0.253650] ACPI: Using IOAPIC for interrupt routing
[ 0.294296] ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62
[ 0.294593] ACPI: No dock devices found.
[ 0.294598] HEST: Table not found.
[ 0.294604] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.303828] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.304172] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
[ 0.304177] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
[ 0.304182] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 0.304186] pci_root PNP0A08:00: host bridge window [mem 0x000c0000-0x000c3fff]
[ 0.304190] pci_root PNP0A08:00: host bridge window [mem 0x000c4000-0x000c7fff]
[ 0.304194] pci_root PNP0A08:00: host bridge window [mem 0x000c8000-0x000cbfff]
[ 0.304198] pci_root PNP0A08:00: host bridge window [mem 0x000cc000-0x000cffff]
[ 0.304202] pci_root PNP0A08:00: host bridge window [mem 0x000d0000-0x000d3fff]
[ 0.304206] pci_root PNP0A08:00: host bridge window [mem 0x000d4000-0x000d7fff]
[ 0.304210] pci_root PNP0A08:00: host bridge window [mem 0x000d8000-0x000dbfff]
[ 0.304214] pci_root PNP0A08:00: host bridge window [mem 0x000dc000-0x000dffff]
[ 0.304218] pci_root PNP0A08:00: host bridge window [mem 0x000e0000-0x000e3fff]
[ 0.304222] pci_root PNP0A08:00: host bridge window [mem 0x000e4000-0x000e7fff]
[ 0.304226] pci_root PNP0A08:00: host bridge window [mem 0x000e8000-0x000ebfff]
[ 0.304230] pci_root PNP0A08:00: host bridge window [mem 0x000ec000-0x000effff]
[ 0.304234] pci_root PNP0A08:00: host bridge window [mem 0xe0000000-0xf7ffffff]
[ 0.304238] pci_root PNP0A08:00: host bridge window [mem 0xfc000000-0xffffffff]
[ 0.304265] pci 0000:00:00.0: [1022:1510] type 0 class 0x000600
[ 0.304322] pci 0000:00:01.0: [1002:9802] type 0 class 0x000300
[ 0.304337] pci 0000:00:01.0: reg 10: [mem 0xe0000000-0xefffffff pref]
[ 0.304347] pci 0000:00:01.0: reg 14: [io 0x3000-0x30ff]
[ 0.304357] pci 0000:00:01.0: reg 18: [mem 0xf0200000-0xf023ffff]
[ 0.304404] pci 0000:00:01.0: supports D1 D2
[ 0.304435] pci 0000:00:01.1: [1002:1314] type 0 class 0x000403
[ 0.304448] pci 0000:00:01.1: reg 10: [mem 0xf0244000-0xf0247fff]
[ 0.304506] pci 0000:00:01.1: supports D1 D2
[ 0.304585] pci 0000:00:04.0: [1022:1512] type 1 class 0x000604
[ 0.304645] pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
[ 0.304651] pci 0000:00:04.0: PME# disabled
[ 0.304684] pci 0000:00:05.0: [1022:1513] type 1 class 0x000604
[ 0.304743] pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
[ 0.304748] pci 0000:00:05.0: PME# disabled
[ 0.304811] pci 0000:00:11.0: [1002:4391] type 0 class 0x000106
[ 0.304838] pci 0000:00:11.0: reg 10: [io 0x3118-0x311f]
[ 0.304852] pci 0000:00:11.0: reg 14: [io 0x3124-0x3127]
[ 0.304866] pci 0000:00:11.0: reg 18: [io 0x3110-0x3117]
[ 0.304880] pci 0000:00:11.0: reg 1c: [io 0x3120-0x3123]
[ 0.304893] pci 0000:00:11.0: reg 20: [io 0x3100-0x310f]
[ 0.304907] pci 0000:00:11.0: reg 24: [mem 0xf024e000-0xf024e3ff]
[ 0.304971] pci 0000:00:12.0: [1002:4397] type 0 class 0x000c03
[ 0.304990] pci 0000:00:12.0: reg 10: [mem 0xf024d000-0xf024dfff]
[ 0.305084] pci 0000:00:12.2: [1002:4396] type 0 class 0x000c03
[ 0.305790] pci 0000:00:12.2: reg 10: [mem 0xf024c000-0xf024c0ff]
[ 0.309643] pci 0000:00:12.2: supports D1 D2
[ 0.309653] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot
[ 0.309661] pci 0000:00:12.2: PME# disabled
[ 0.309703] pci 0000:00:13.0: [1002:4397] type 0 class 0x000c03
[ 0.309726] pci 0000:00:13.0: reg 10: [mem 0xf024b000-0xf024bfff]
[ 0.310052] pci 0000:00:13.2: [1002:4396] type 0 class 0x000c03
[ 0.310717] pci 0000:00:13.2: reg 10: [mem 0xf024a000-0xf024a0ff]
[ 0.314283] pci 0000:00:13.2: supports D1 D2
[ 0.314293] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
[ 0.314302] pci 0000:00:13.2: PME# disabled
[ 0.314343] pci 0000:00:14.0: [1002:4385] type 0 class 0x000c05
[ 0.314451] pci 0000:00:14.2: [1002:4383] type 0 class 0x000403
[ 0.314483] pci 0000:00:14.2: reg 10: [mem 0xf0240000-0xf0243fff 64bit]
[ 0.314560] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
[ 0.314567] pci 0000:00:14.2: PME# disabled
[ 0.314600] pci 0000:00:14.3: [1002:439d] type 0 class 0x000601
[ 0.314701] pci 0000:00:14.4: [1002:4384] type 1 class 0x000604
[ 0.314764] pci 0000:00:16.0: [1002:4397] type 0 class 0x000c03
[ 0.314784] pci 0000:00:16.0: reg 10: [mem 0xf0249000-0xf0249fff]
[ 0.314878] pci 0000:00:16.2: [1002:4396] type 0 class 0x000c03
[ 0.315565] pci 0000:00:16.2: reg 10: [mem 0xf0248000-0xf02480ff]
[ 0.319593] pci 0000:00:16.2: supports D1 D2
[ 0.319602] pci 0000:00:16.2: PME# supported from D0 D1 D2 D3hot
[ 0.319611] pci 0000:00:16.2: PME# disabled
[ 0.319653] pci 0000:00:18.0: [1022:1700] type 0 class 0x000600
[ 0.319704] pci 0000:00:18.1: [1022:1701] type 0 class 0x000600
[ 0.319747] pci 0000:00:18.2: [1022:1702] type 0 class 0x000600
[ 0.320021] pci 0000:00:18.3: [1022:1703] type 0 class 0x000600
[ 0.320088] pci 0000:00:18.4: [1022:1704] type 0 class 0x000600
[ 0.320131] pci 0000:00:18.5: [1022:1718] type 0 class 0x000600
[ 0.320174] pci 0000:00:18.6: [1022:1716] type 0 class 0x000600
[ 0.320216] pci 0000:00:18.7: [1022:1719] type 0 class 0x000600
[ 0.320338] pci 0000:01:00.0: [10ec:8168] type 0 class 0x000200
[ 0.320359] pci 0000:01:00.0: reg 10: [io 0x2000-0x20ff]
[ 0.320392] pci 0000:01:00.0: reg 18: [mem 0xf0004000-0xf0004fff 64bit pref]
[ 0.320412] pci 0000:01:00.0: reg 20: [mem 0xf0000000-0xf0003fff 64bit pref]
[ 0.320466] pci 0000:01:00.0: supports D1 D2
[ 0.320470] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.320477] pci 0000:01:00.0: PME# disabled
[ 0.326731] pci 0000:00:04.0: PCI bridge to [bus 01-01]
[ 0.326751] pci 0000:00:04.0: bridge window [io 0x2000-0x2fff]
[ 0.326762] pci 0000:00:04.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
[ 0.326771] pci 0000:00:04.0: bridge window [mem 0xf0000000-0xf00fffff 64bit pref]
[ 0.326884] pci 0000:02:00.0: [1814:539f] type 0 class 0x000280
[ 0.326908] pci 0000:02:00.0: reg 10: [mem 0xf0100000-0xf010ffff]
[ 0.333424] pci 0000:00:05.0: PCI bridge to [bus 02-02]
[ 0.333437] pci 0000:00:05.0: bridge window [io 0xfffffffffffff000-0x0000] (disabled)
[ 0.333445] pci 0000:00:05.0: bridge window [mem 0xf0100000-0xf01fffff]
[ 0.333454] pci 0000:00:05.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.333600] pci 0000:00:14.4: PCI bridge to [bus 03-03] (subtractive decode)
[ 0.333607] pci 0000:00:14.4: bridge window [io 0xf000-0x0000] (disabled)
[ 0.333615] pci 0000:00:14.4: bridge window [mem 0xfff00000-0x000fffff] (disabled)
[ 0.333622] pci 0000:00:14.4: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.333627] pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 0.333631] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 0.333636] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.333640] pci 0000:00:14.4: bridge window [mem 0x000c0000-0x000c3fff] (subtractive decode)
[ 0.333645] pci 0000:00:14.4: bridge window [mem 0x000c4000-0x000c7fff] (subtractive decode)
[ 0.333649] pci 0000:00:14.4: bridge window [mem 0x000c8000-0x000cbfff] (subtractive decode)
[ 0.333653] pci 0000:00:14.4: bridge window [mem 0x000cc000-0x000cffff] (subtractive decode)
[ 0.333657] pci 0000:00:14.4: bridge window [mem 0x000d0000-0x000d3fff] (subtractive decode)
[ 0.333662] pci 0000:00:14.4: bridge window [mem 0x000d4000-0x000d7fff] (subtractive decode)
[ 0.333666] pci 0000:00:14.4: bridge window [mem 0x000d8000-0x000dbfff] (subtractive decode)
[ 0.333670] pci 0000:00:14.4: bridge window [mem 0x000dc000-0x000dffff] (subtractive decode)
[ 0.333675] pci 0000:00:14.4: bridge window [mem 0x000e0000-0x000e3fff] (subtractive decode)
[ 0.333679] pci 0000:00:14.4: bridge window [mem 0x000e4000-0x000e7fff] (subtractive decode)
[ 0.333683] pci 0000:00:14.4: bridge window [mem 0x000e8000-0x000ebfff] (subtractive decode)
[ 0.333688] pci 0000:00:14.4: bridge window [mem 0x000ec000-0x000effff] (subtractive decode)
[ 0.333692] pci 0000:00:14.4: bridge window [mem 0xe0000000-0xf7ffffff] (subtractive decode)
[ 0.333696] pci 0000:00:14.4: bridge window [mem 0xfc000000-0xffffffff] (subtractive decode)
[ 0.333730] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.333965] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB4_._PRT]
[ 0.334034] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB5_._PRT]
[ 0.334166] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
[ 0.334455] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 0.334981] pci0000:00: ACPI _OSC control (0x19) granted
[ 0.346082] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 0.346217] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 0.346353] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 0.346488] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 0.346625] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 0.346714] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 0.346789] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 0.346863] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 0.347047] vgaarb: device added: PCI:0000:00:01.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.347068] vgaarb: loaded
[ 0.347225] PCI: Using ACPI for IRQ routing
[ 0.347231] PCI: pci_cache_line_size set to 64 bytes
[ 0.347435] reserve RAM buffer: 000000000009f800 - 000000000009ffff
[ 0.347439] reserve RAM buffer: 00000000dfa3f000 - 00000000dfffffff
[ 0.347444] reserve RAM buffer: 00000000dff00000 - 00000000dfffffff
[ 0.347447] reserve RAM buffer: 0000000187000000 - 0000000187ffffff
[ 0.347671] NetLabel: Initializing
[ 0.347675] NetLabel: domain hash size = 128
[ 0.347677] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.347700] NetLabel: unlabeled traffic allowed by default
[ 0.347731] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.347738] hpet0: 3 comparators, 32-bit 14.318180 MHz counter
[ 0.349771] Switching to clocksource hpet
[ 0.349869] Switched to NOHz mode on CPU #1
[ 0.350046] Switched to NOHz mode on CPU #0
[ 0.357491] pnp: PnP ACPI init
[ 0.357525] ACPI: bus type pnp registered
[ 0.357763] pnp 00:00: [bus 00-ff]
[ 0.357768] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.357772] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.357777] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.357781] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[ 0.357785] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[ 0.357789] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[ 0.357793] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[ 0.357797] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[ 0.357800] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[ 0.357804] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[ 0.357808] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[ 0.357811] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[ 0.357815] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[ 0.357818] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[ 0.357822] pnp 00:00: [mem 0x000ec000-0x000effff window]
[ 0.357826] pnp 00:00: [mem 0xe0000000-0xf7ffffff window]
[ 0.357829] pnp 00:00: [mem 0xfc000000-0xffffffff window]
[ 0.357833] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.357945] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 0.358035] pnp 00:01: [mem 0xfec00000-0xfec00fff]
[ 0.358039] pnp 00:01: [mem 0xfee00000-0xfee00fff]
[ 0.358135] system 00:01: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.358141] system 00:01: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.358147] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.358359] pnp 00:02: [irq 0 disabled]
[ 0.358392] pnp 00:02: [irq 8]
[ 0.358396] pnp 00:02: [mem 0xfed00000-0xfed003ff]
[ 0.358441] pnp 00:02: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.358562] pnp 00:03: [io 0x0000-0x000f]
[ 0.358566] pnp 00:03: [io 0x0081-0x008f]
[ 0.358570] pnp 00:03: [io 0x00c0-0x00df]
[ 0.358574] pnp 00:03: [dma 4]
[ 0.358630] pnp 00:03: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.358647] pnp 00:04: [io 0x00f0-0x00fe]
[ 0.358671] pnp 00:04: [irq 13]
[ 0.358734] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.358812] pnp 00:05: [io 0x0070-0x0071]
[ 0.358869] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.358889] pnp 00:06: [io 0x0060]
[ 0.358892] pnp 00:06: [io 0x0064]
[ 0.358901] pnp 00:06: [irq 1]
[ 0.358958] pnp 00:06: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.358979] pnp 00:07: [irq 12]
[ 0.359045] pnp 00:07: Plug and Play ACPI device, IDs SYN1e3b SYN1e00 SYN0002 PNP0f13 (active)
[ 0.359066] pnp 00:08: [io 0x0010-0x001f]
[ 0.359069] pnp 00:08: [io 0x002e-0x002f]
[ 0.359072] pnp 00:08: [io 0x0072-0x0073]
[ 0.359075] pnp 00:08: [io 0x0080]
[ 0.359078] pnp 00:08: [io 0x00b0-0x00b1]
[ 0.359081] pnp 00:08: [io 0x0092]
[ 0.359084] pnp 00:08: [io 0x0400-0x04cf]
[ 0.359088] pnp 00:08: [io 0x04d0-0x04d1]
[ 0.359091] pnp 00:08: [io 0x04d6]
[ 0.359094] pnp 00:08: [io 0x0680-0x06ff]
[ 0.359097] pnp 00:08: [io 0x077a]
[ 0.359100] pnp 00:08: [io 0x0c00-0x0c01]
[ 0.359102] pnp 00:08: [io 0x0c14]
[ 0.359106] pnp 00:08: [io 0x0c50-0x0c52]
[ 0.359109] pnp 00:08: [io 0x0c6c]
[ 0.359111] pnp 00:08: [io 0x0c6f]
[ 0.359114] pnp 00:08: [io 0x0cd0-0x0cdb]
[ 0.359216] system 00:08: [io 0x0400-0x04cf] has been reserved
[ 0.359221] system 00:08: [io 0x04d0-0x04d1] has been reserved
[ 0.359225] system 00:08: [io 0x04d6] has been reserved
[ 0.359230] system 00:08: [io 0x0680-0x06ff] has been reserved
[ 0.359234] system 00:08: [io 0x077a] has been reserved
[ 0.359238] system 00:08: [io 0x0c00-0x0c01] has been reserved
[ 0.359242] system 00:08: [io 0x0c14] has been reserved
[ 0.359246] system 00:08: [io 0x0c50-0x0c52] has been reserved
[ 0.359251] system 00:08: [io 0x0c6c] has been reserved
[ 0.359255] system 00:08: [io 0x0c6f] has been reserved
[ 0.359259] system 00:08: [io 0x0cd0-0x0cdb] has been reserved
[ 0.359265] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.359348] pnp 00:09: [mem 0x000e0000-0x000fffff]
[ 0.359353] pnp 00:09: [mem 0xffe00000-0xffffffff]
[ 0.359450] system 00:09: [mem 0x000e0000-0x000fffff] could not be reserved
[ 0.359456] system 00:09: [mem 0xffe00000-0xffffffff] has been reserved
[ 0.359462] system 00:09: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.361159] pnp 00:0a: [irq 23]
[ 0.361298] pnp 00:0a: Plug and Play ACPI device, IDs HPQ0004 (active)
[ 0.361323] pnp: PnP ACPI: found 11 devices
[ 0.361326] ACPI: ACPI bus type pnp unregistered
[ 0.369286] pci 0000:00:04.0: PCI bridge to [bus 01-01]
[ 0.369294] pci 0000:00:04.0: bridge window [io 0x2000-0x2fff]
[ 0.369300] pci 0000:00:04.0: bridge window [mem disabled]
[ 0.369307] pci 0000:00:04.0: bridge window [mem 0xf0000000-0xf00fffff 64bit pref]
[ 0.369315] pci 0000:00:05.0: PCI bridge to [bus 02-02]
[ 0.369318] pci 0000:00:05.0: bridge window [io disabled]
[ 0.369325] pci 0000:00:05.0: bridge window [mem 0xf0100000-0xf01fffff]
[ 0.369330] pci 0000:00:05.0: bridge window [mem pref disabled]
[ 0.369337] pci 0000:00:14.4: PCI bridge to [bus 03-03]
[ 0.369340] pci 0000:00:14.4: bridge window [io disabled]
[ 0.369362] pci 0000:00:14.4: bridge window [mem disabled]
[ 0.369368] pci 0000:00:14.4: bridge window [mem pref disabled]
[ 0.369400] pci 0000:00:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.369408] pci 0000:00:04.0: setting latency timer to 64
[ 0.369422] pci 0000:00:05.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.369428] pci 0000:00:05.0: setting latency timer to 64
[ 0.369440] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.369444] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.369448] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.369452] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000c3fff]
[ 0.369456] pci_bus 0000:00: resource 8 [mem 0x000c4000-0x000c7fff]
[ 0.369460] pci_bus 0000:00: resource 9 [mem 0x000c8000-0x000cbfff]
[ 0.369464] pci_bus 0000:00: resource 10 [mem 0x000cc000-0x000cffff]
[ 0.369468] pci_bus 0000:00: resource 11 [mem 0x000d0000-0x000d3fff]
[ 0.369472] pci_bus 0000:00: resource 12 [mem 0x000d4000-0x000d7fff]
[ 0.369476] pci_bus 0000:00: resource 13 [mem 0x000d8000-0x000dbfff]
[ 0.369480] pci_bus 0000:00: resource 14 [mem 0x000dc000-0x000dffff]
[ 0.369484] pci_bus 0000:00: resource 15 [mem 0x000e0000-0x000e3fff]
[ 0.369487] pci_bus 0000:00: resource 16 [mem 0x000e4000-0x000e7fff]
[ 0.369491] pci_bus 0000:00: resource 17 [mem 0x000e8000-0x000ebfff]
[ 0.369495] pci_bus 0000:00: resource 18 [mem 0x000ec000-0x000effff]
[ 0.369499] pci_bus 0000:00: resource 19 [mem 0xe0000000-0xf7ffffff]
[ 0.369503] pci_bus 0000:00: resource 20 [mem 0xfc000000-0xffffffff]
[ 0.369507] pci_bus 0000:01: resource 0 [io 0x2000-0x2fff]
[ 0.369512] pci_bus 0000:01: resource 2 [mem 0xf0000000-0xf00fffff 64bit pref]
[ 0.369516] pci_bus 0000:02: resource 1 [mem 0xf0100000-0xf01fffff]
[ 0.369520] pci_bus 0000:03: resource 4 [io 0x0000-0x0cf7]
[ 0.369524] pci_bus 0000:03: resource 5 [io 0x0d00-0xffff]
[ 0.369528] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.369532] pci_bus 0000:03: resource 7 [mem 0x000c0000-0x000c3fff]
[ 0.369535] pci_bus 0000:03: resource 8 [mem 0x000c4000-0x000c7fff]
[ 0.369539] pci_bus 0000:03: resource 9 [mem 0x000c8000-0x000cbfff]
[ 0.369543] pci_bus 0000:03: resource 10 [mem 0x000cc000-0x000cffff]
[ 0.369547] pci_bus 0000:03: resource 11 [mem 0x000d0000-0x000d3fff]
[ 0.369551] pci_bus 0000:03: resource 12 [mem 0x000d4000-0x000d7fff]
[ 0.369555] pci_bus 0000:03: resource 13 [mem 0x000d8000-0x000dbfff]
[ 0.369559] pci_bus 0000:03: resource 14 [mem 0x000dc000-0x000dffff]
[ 0.369562] pci_bus 0000:03: resource 15 [mem 0x000e0000-0x000e3fff]
[ 0.369566] pci_bus 0000:03: resource 16 [mem 0x000e4000-0x000e7fff]
[ 0.369570] pci_bus 0000:03: resource 17 [mem 0x000e8000-0x000ebfff]
[ 0.369574] pci_bus 0000:03: resource 18 [mem 0x000ec000-0x000effff]
[ 0.369578] pci_bus 0000:03: resource 19 [mem 0xe0000000-0xf7ffffff]
[ 0.369582] pci_bus 0000:03: resource 20 [mem 0xfc000000-0xffffffff]
[ 0.369723] NET: Registered protocol family 2
[ 0.370245] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.373075] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[ 0.378850] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.379526] TCP: Hash tables configured (established 524288 bind 65536)
[ 0.379531] TCP reno registered
[ 0.379569] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.379687] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.380300] NET: Registered protocol family 1
[ 0.380331] pci 0000:00:01.0: Boot video device
[ 0.460342] PCI: CLS 64 bytes, default 64
[ 0.460446] Unpacking initramfs...
[ 0.505657] Freeing initrd memory: 1700k freed
[ 0.506819] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.506828] Placing 64MB software IO TLB between ffff8800dba3f000 - ffff8800dfa3f000
[ 0.506832] software IO TLB at phys 0xdba3f000 - 0xdfa3f000
[ 0.506921] Simple Boot Flag at 0x44 set to 0x1
[ 0.507647] audit: initializing netlink socket (disabled)
[ 0.507672] type=2000 audit(1308931391.506:1): initialized
[ 0.509016] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.513968] VFS: Disk quotas dquot_6.5.2
[ 0.514241] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.514554] msgmni has been set to 11166
[ 0.515475] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.515770] io scheduler noop registered
[ 0.515778] io scheduler deadline registered
[ 0.515922] io scheduler cfq registered (default)
[ 0.516411] ERST: Table is not found!
[ 0.516539] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.740924] Linux agpgart interface v0.103
[ 0.741073] i8042: PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 0.747470] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.747529] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.747687] mousedev: PS/2 mouse device common for all mice
[ 0.747867] rtc_cmos 00:05: RTC can wake from S4
[ 0.753544] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 0.767132] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 0.767186] rtc0: alarms up to one month, 114 bytes nvram, hpet irqs
[ 0.767213] cpuidle: using governor ladder
[ 0.767217] cpuidle: using governor menu
[ 0.767576] TCP cubic registered
[ 0.767581] NET: Registered protocol family 17
[ 0.767593] Registering the dns_resolver key type
[ 0.767764] PM: Hibernation image not present or could not be loaded.
[ 0.767778] registered taskstats version 1
[ 0.768843] rtc_cmos 00:05: setting system clock to 2011-06-24 16:03:12 UTC (1308931392)
[ 0.768918] Initializing network drop monitor service
[ 0.771516] Freeing unused kernel memory: 724k freed
[ 0.771916] Write protecting the kernel read-only data: 6144k
[ 0.772631] Freeing unused kernel memory: 56k freed
[ 0.777964] Freeing unused kernel memory: 784k freed
[ 0.815303] udevd[59]: starting version 171
[ 0.987592] SCSI subsystem initialized
[ 1.022258] libata version 3.00 loaded.
[ 1.036343] ahci 0000:00:11.0: version 3.0
[ 1.036385] ahci 0000:00:11.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 1.036532] ahci 0000:00:11.0: AHCI 0001.0200 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
[ 1.036539] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part
[ 1.037084] scsi0 : ahci
[ 1.037252] ata1: SATA max UDMA/133 abar m1024@0xf024e000 port 0xf024e100 irq 19
[ 1.510277] Refined TSC clocksource calibration: 1596.003 MHz.
[ 1.510296] Switching to clocksource tsc
[ 6.856991] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 6.857578] ata1.00: ATA-7: INTEL SSDSA2M080G2GC, 2CV102HD, max UDMA/133
[ 6.857585] ata1.00: 156301488 sectors, multi 1: LBA48 NCQ (depth 31/32)
[ 6.858264] ata1.00: configured for UDMA/133
[ 6.858756] scsi 0:0:0:0: Direct-Access ATA INTEL SSDSA2M080 2CV1 PQ: 0 ANSI: 5
[ 6.871132] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 6.871271] sd 0:0:0:0: [sda] Write Protect is off
[ 6.871276] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 6.871320] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 6.872158] sda: sda1
[ 6.873464] sd 0:0:0:0: [sda] Attached SCSI disk
[ 7.051357] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 7.707862] udevd[230]: starting version 171
[ 7.759090] ACPI: acpi_idle registered with cpuidle
[ 7.766584] powernow-k8: Found 1 AMD E-350 Processor (2 cpu cores) (version 2.20.00)
[ 7.766662] powernow-k8: 0 : pstate 0 (1600 MHz)
[ 7.766699] powernow-k8: 1 : pstate 1 (1280 MHz)
[ 7.766703] powernow-k8: 2 : pstate 2 (800 MHz)
[ 7.798328] rt5390 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 7.798437] rt5390 0000:02:00.0: setting latency timer to 64
[ 7.798971] <-- RTMPAllocAdapterBlock, Status=0
[ 7.860369] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 7.860383] ACPI: Power Button [PWRB]
[ 7.860558] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2
[ 7.861604] ACPI: Lid Switch [LID]
[ 7.861751] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 7.861761] ACPI: Power Button [PWRF]
[ 7.897248] vboxdrv: Found 2 processor cores.
[ 7.897357] VBoxDrv: dbg - g_abExecMemory=ffffffffa0276360
[ 7.897405] vboxdrv: fAsync=0 offMin=0x35d offMax=0xcf6
[ 7.897484] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 7.897488] vboxdrv: Successfully loaded version 4.0.8_OSE (interface 0x00180000).
[ 7.932205] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[ 7.934073] ACPI: AC Adapter [AC] (off-line)
[ 7.934370] wmi: Mapper loaded
[ 7.961127] acpi device:02: registered as cooling_device2
[ 7.961272] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input4
[ 7.961285] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 8.003256] SP5100 TCO timer: SP5100 TCO WatchDog Timer Driver v0.01
[ 8.003495] SP5100 TCO timer: mmio address 0xb8fe00 already in use
[ 8.014954] ACPI Warning: For \_TZ_.THRM._AL0: Return Package has no elements (empty) (20110316/nspredef-456)
[ 8.014969] ACPI: [Package] has zero elements (ffff88017c138cc0)
[ 8.014973] ACPI: Invalid active0 threshold
[ 8.025488] thermal LNXTHERM:00: registered as thermal_zone0
[ 8.025495] ACPI: Thermal Zone [THRM] (52 C)
[ 8.044849] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[ 8.044866] ACPI: Battery Slot [BAT0] (battery present)
[ 8.076882] hp_accel: laptop model unknown, using default axes configuration
[ 8.109541] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 8.112918] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 8.112984] r8169 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 8.113075] r8169 0000:01:00.0: setting latency timer to 64
[ 8.113083] r8169 0000:01:00.0: (unregistered net_device): unknown MAC, using family default
[ 8.113141] r8169 0000:01:00.0: irq 40 for MSI/MSI-X
[ 8.113883] r8169 0000:01:00.0: eth0: RTL8168b/8111b at 0xffffc90000c34000, 68:b5:99:e1:fa:b1, XID 0c200000 IRQ 40
[ 8.145250] usbcore: registered new interface driver usbfs
[ 8.145307] usbcore: registered new interface driver hub
[ 8.146258] usbcore: registered new device driver usb
[ 8.147469] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[ 8.211672] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.211773] ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 8.211870] ehci_hcd 0000:00:12.2: setting latency timer to 64
[ 8.211878] ehci_hcd 0000:00:12.2: EHCI Host Controller
[ 8.211930] ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 1
[ 8.226790] ehci_hcd 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 8.226839] QUIRK: Enable AMD PLL fix
[ 8.226874] ehci_hcd 0000:00:12.2: debug port 1
[ 8.226916] ehci_hcd 0000:00:12.2: irq 17, io mem 0xf024c000
[ 8.236710] ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00
[ 8.237083] hub 1-0:1.0: USB hub found
[ 8.237094] hub 1-0:1.0: 5 ports detected
[ 8.237272] ehci_hcd 0000:00:13.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 8.237336] ehci_hcd 0000:00:13.2: setting latency timer to 64
[ 8.237342] ehci_hcd 0000:00:13.2: EHCI Host Controller
[ 8.237361] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 2
[ 8.246722] ehci_hcd 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 8.246777] ehci_hcd 0000:00:13.2: debug port 1
[ 8.246803] ehci_hcd 0000:00:13.2: irq 17, io mem 0xf024a000
[ 8.255280] [drm] Initialized drm 1.1.0 20060810
[ 8.256809] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00
[ 8.257138] hub 2-0:1.0: USB hub found
[ 8.257148] hub 2-0:1.0: 5 ports detected
[ 8.257353] ehci_hcd 0000:00:16.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 8.257432] ehci_hcd 0000:00:16.2: setting latency timer to 64
[ 8.257438] ehci_hcd 0000:00:16.2: EHCI Host Controller
[ 8.257456] ehci_hcd 0000:00:16.2: new USB bus registered, assigned bus number 3
[ 8.266735] ehci_hcd 0000:00:16.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 8.266794] ehci_hcd 0000:00:16.2: debug port 1
[ 8.266822] ehci_hcd 0000:00:16.2: irq 17, io mem 0xf0248000
[ 8.280083] ehci_hcd 0000:00:16.2: USB 2.0 started, EHCI 1.00
[ 8.280419] hub 3-0:1.0: USB hub found
[ 8.280429] hub 3-0:1.0: 4 ports detected
[ 8.299920] input: HP WMI hotkeys as /devices/virtual/input/input5
[ 8.368162] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 8.368219] ohci_hcd 0000:00:12.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 8.368296] ohci_hcd 0000:00:12.0: setting latency timer to 64
[ 8.368303] ohci_hcd 0000:00:12.0: OHCI Host Controller
[ 8.368334] ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 4
[ 8.383583] ohci_hcd 0000:00:12.0: irq 18, io mem 0xf024d000
[ 8.438348] [drm] VGACON disable radeon kernel modesetting.
[ 8.439661] pci 0000:00:01.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 8.439670] pci 0000:00:01.0: setting latency timer to 64
[ 8.440157] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 8.440162] [drm] No driver support for vblank timestamp query.
[ 8.440168] [drm] Initialized radeon 1.33.0 20080528 for 0000:00:01.0 on minor 0
[ 8.441308] hub 4-0:1.0: USB hub found
[ 8.441368] hub 4-0:1.0: 5 ports detected
[ 8.441720] ohci_hcd 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 8.441833] ohci_hcd 0000:00:13.0: setting latency timer to 64
[ 8.441841] ohci_hcd 0000:00:13.0: OHCI Host Controller
[ 8.441860] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 5
[ 8.456856] ohci_hcd 0000:00:13.0: irq 18, io mem 0xf024b000
[ 8.477927] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[ 8.477937] Disabling lock debugging due to kernel taint
[ 8.514652] hub 5-0:1.0: USB hub found
[ 8.514713] hub 5-0:1.0: 5 ports detected
[ 8.514902] HDA Intel 0000:00:01.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 8.515007] HDA Intel 0000:00:01.1: irq 41 for MSI/MSI-X
[ 8.515044] HDA Intel 0000:00:01.1: setting latency timer to 64
[ 8.534738] HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 8.534853] HDA Intel 0000:00:14.2: setting latency timer to 64
[ 8.566706] usb 2-1: new high speed USB device number 2 using ehci_hcd
[ 8.583897] [fglrx] Maximum main memory to use for locked dma buffers: 5393 MBytes.
[ 8.583979] [fglrx] vendor: 1002 device: 9802 count: 1
[ 8.584734] [fglrx] ioport: bar 1, base 0x3000, size: 0x100
[ 8.584748] pci 0000:00:01.0: setting latency timer to 64
[ 8.585495] [fglrx] Kernel PAT support is enabled
[ 8.585539] [fglrx] module loaded - fglrx 8.86.5 [May 24 2011] with 1 minors
[ 8.598000] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:14.2/input/input6
[ 8.614292] input: HDA ATI SB Mic at Ext Right Jack as /devices/pci0000:00/0000:00:14.2/sound/card1/input7
[ 8.614454] input: HDA ATI SB HP Out at Ext Right Jack as /devices/pci0000:00/0000:00:14.2/sound/card1/input8
[ 8.614783] ohci_hcd 0000:00:16.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 8.614861] ohci_hcd 0000:00:16.0: setting latency timer to 64
[ 8.614869] ohci_hcd 0000:00:16.0: OHCI Host Controller
[ 8.614900] ohci_hcd 0000:00:16.0: new USB bus registered, assigned bus number 6
[ 8.623464] ohci_hcd 0000:00:16.0: irq 18, io mem 0xf0249000
[ 8.681124] hub 6-0:1.0: USB hub found
[ 8.681137] hub 6-0:1.0: 4 ports detected
[ 8.892947] Synaptics Touchpad, model: 1, fw: 7.4, id: 0x1e0b1, caps: 0xd04773/0xe40000/0x5a0400
[ 8.940407] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input9
[ 9.016651] lis3lv02d: 8 bits 3DC sensor found
[ 9.403986] Linux media interface: v0.10
[ 9.420636] Linux video capture interface: v2.00
[ 9.429080] uvcvideo: Found UVC 1.00 device HP Webcam-101 (174f:112b)
[ 9.455290] input: HP Webcam-101 as /devices/pci0000:00/0000:00:13.2/usb2/2-1/2-1:1.0/input/input10
[ 9.455419] usbcore: registered new interface driver uvcvideo
[ 9.455423] USB Video Class driver (v1.0.0)
[ 9.460103] usb 2-2: new high speed USB device number 3 using ehci_hcd
[ 9.960350] usb 6-1: new full speed USB device number 2 using ohci_hcd
[ 10.246250] Bluetooth: Core ver 2.16
[ 10.246292] NET: Registered protocol family 31
[ 10.246295] Bluetooth: HCI device and connection manager initialized
[ 10.246300] Bluetooth: HCI socket layer initialized
[ 10.246303] Bluetooth: L2CAP socket layer initialized
[ 10.250254] Bluetooth: SCO socket layer initialized
[ 10.265755] Initializing USB Mass Storage driver...
[ 10.265954] usbcore: registered new interface driver usb-storage
[ 10.265957] USB Mass Storage support registered.
[ 10.270760] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 10.271722] usbcore: registered new interface driver btusb
[ 10.288479] scsi1 : usb-storage 2-2:1.0
[ 10.288755] usbcore: registered new interface driver ums-realtek
[ 10.293708] usbcore: registered new interface driver uas
[ 10.430407] input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d/input/input11
[ 10.430745] Registered led device: hp::hddprotect
[ 10.430769] hp_accel: driver loaded
[ 10.526540] EXT4-fs (sda1): re-mounted. Opts: discard
[ 11.289737] scsi 1:0:0:0: Direct-Access Generic- Multi-Card 1.00 PQ: 0 ANSI: 0 CCS
[ 11.290445] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 11.312911] fuse init (API version 7.16)
[ 11.519361] r8169 0000:01:00.0: eth0: link down
[ 11.527370] KH: Use High Memory for Beacon
[ 11.531213] <-- RTMPAllocTxRxRingMemory, Status=0
[ 11.588181] <==== rt28xx_init, Status=0
[ 11.588301] 0x1300 = 00064300
[ 12.021213] sd 1:0:0:0: [sdb] 3987456 512-byte logical blocks: (2.04 GB/1.90 GiB)
[ 12.023162] sd 1:0:0:0: [sdb] Write Protect is off
[ 12.023168] sd 1:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 12.023172] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 12.025360] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 12.027256] sdb: sdb1
[ 12.031613] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 12.031628] sd 1:0:0:0: [sdb] Attached SCSI removable disk
[ 12.486029] fglrx_pci 0000:00:01.0: irq 42 for MSI/MSI-X
[ 12.486918] [fglrx] Firegl kernel thread PID: 779
[ 12.486999] [fglrx] Firegl kernel thread PID: 780
[ 12.487080] [fglrx] Firegl kernel thread PID: 781
[ 12.487290] [fglrx] IRQ 42 Enabled
[ 12.612000] [fglrx] Gart USWC size:1280 M.
[ 12.612007] [fglrx] Gart cacheable size:508 M.
[ 12.612017] [fglrx] Reserved FB block: Shared offset:0, size:1000000
[ 12.612021] [fglrx] Reserved FB block: Unshared offset:fbfd000, size:403000
[ 12.612025] [fglrx] Reserved FB block: Unshared offset:17ff4000, size:c000
[ 25.342715] EXT4-fs (sda1): re-mounted. Opts: discard,commit=600
[ 39.000090] NET: Registered protocol family 10
[ 39.001989] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 39.648846] hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj.The Open Toolkit: OpenGL, OpenAL, OpenCL and Vulkan for Mono/.Net.
Offline