Arch Linux

signor_rossi

Member

Registered: 2007-08-24

Posts: 257

Who has got an USB-3.0 PCI-E card working? Which one?

I can't get this one to work with a WD MyBook Essential USB-3.0 external hard disk:

02:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30 [XHCI])
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 32 bytes
    Interrupt: pin A routed to IRQ 18
    Region 0: Memory at fdafe000 (64-bit, non-prefetchable) [size=8K]
    Capabilities: [50] Power Management version 3
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
        Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+
        Address: 0000000000000000  Data: 0000
    Capabilities: [90] MSI-X: Enable- Count=8 Masked-
        Vector table: BAR=0 offset=00001000
        PBA: BAR=0 offset=00001080
    Capabilities: [a0] Express (v2) Endpoint, MSI 00
        DevCap:    MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
            ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
        DevCtl:    Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
            RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
            MaxPayload 128 bytes, MaxReadReq 512 bytes
        DevSta:    CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
        LnkCap:    Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <4us, L1 unlimited
            ClockPM+ Surprise- LLActRep- BwNot-
        LnkCtl:    ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
            ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
        LnkSta:    Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
        DevCap2: Completion Timeout: Not Supported, TimeoutDis+
        DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
        LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
             Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
             Compliance De-emphasis: -6dB
        LnkSta2: Current De-emphasis Level: -3.5dB
    Capabilities: [100 v1] Advanced Error Reporting
        UESta:    DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
        UEMsk:    DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
        UESvrt:    DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
        CESta:    RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
        CEMsk:    RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
        AERCap:    First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
    Capabilities: [140 v1] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff
    Capabilities: [150 v1] #18
    Kernel driver in use: xhci_hcd
    Kernel modules: xhci-hcd

USB-2.0 devices work on it, btw and the hard disk works on an USB-2.0 port. I have tried to search the forums and google a solution, but to no avail.
This is the dmesg output:

[ 6383.586074] usb 1-2: new high speed USB device number 2 using xhci_hcd
[ 6383.786581] usb 1-2: Device not responding to set address.
[ 6383.989491] usb 1-2: Device not responding to set address.
[ 6384.192737] usb 1-2: device not accepting address 2, error -71
[ 6384.246081] hub 1-0:1.0: unable to enumerate USB device on port 2

signor_rossi

Member

Registered: 2007-08-24

Posts: 257

Re: Who has got an USB-3.0 PCI-E card working? Which one?

BUMP...
Problem still persists with newest kernel.