Arch Linux

vjoe

Member

From: Milton Keynes

Registered: 2008-06-14

Posts: 72

Can't burn disks with wodim

Hey guys,

Wodim is not working for me. I am in the optical group.

This is the message I got when I tried to burn the cd:

wodim: No write mode specified.
wodim: Assuming -tao mode.
wodim: Future versions of wodim may have different drive dependent defaults.
wodim: Operation not permitted. Warning: Cannot raise RLIMIT_MEMLOCK limits.
scsidev: '/dev/sr0'
devname: '/dev/sr0'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.11
SCSI buffer size: 64512
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
TOC Type: 3 = CD-ROM XA mode 2
Driveropts: 'burnfree'
Device type    : Removable CD-ROM
Version        : 5
Response Format: 2
Capabilities   :
Vendor_info    : 'HL-DT-ST'
Identification : 'DVDRAM GSA-T20L '
Revision       : 'NR02'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x0009 (CD-R)
Profile: 0x0012 (DVD-RAM)
Profile: 0x0011 (DVD-R sequential recording)
Profile: 0x0015 (DVD-R/DL sequential recording)
Profile: 0x0014 (DVD-RW sequential recording)
Profile: 0x0013 (DVD-RW restricted overwrite)
Profile: 0x001A (DVD+RW)
Profile: 0x001B (DVD+R)
Profile: 0x002B (DVD+R/DL)
Profile: 0x0010 (DVD-ROM)
Profile: 0x0009 (CD-R) (current)
Profile: 0x000A (CD-RW)
Profile: 0x0008 (CD-ROM)
Profile: 0x0002 (Removable disk)
Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
Driver flags   : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 1053696 = 1029 KB
Drive DMA Speed: 13610 kB/s 77x CD 9x DVD
FIFO size      : 4194304 = 4096 KB
Speed set to 4234 KB/s
   4 seconds.   3 seconds.   2 seconds.   1 seconds.   0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...
Starting new track at sector: 0
Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
CDB:  2A 00 00 00 01 B2 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 03 00 00 00 00 0A 3C 30 00 80 02 00 00 00
Sense Key: 0x3 Medium Error, Segment 0
Sense Code: 0x02 Qual 0x00 (no seek complete) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 12.602s timeout 40s
wodim: A write error occured.
wodim: Please properly read the error message above.
Errno: 5 (Input/output error), test unit ready scsi sendcmd: no error
CDB:  00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 71 00 03 00 00 00 00 0A 3C 30 00 80 02 00 00 00
Sense Key: 0x3 Medium Error, deferred error, Segment 0
Sense Code: 0x02 Qual 0x00 (no seek complete) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.003s timeout 40s

write track data: error after 888832 bytes
Writing  time:   36.019s
Average write speed 132.3x.
Fixating...
Fixating time:    0.005s

Can I have some help please?

Thank you

karol

Archivist

Registered: 2009-05-06

Posts: 25,440

Re: Can't burn disks with wodim

Please use [ code ] tags when pasting code https://bbs.archlinux.org/help.php#bbcode

When reporting problems, it's important you provide not only the output, but also the command you used.

Was this drive burning CDs OK before?