You are not logged in.

Pages: 1

#1 2011-09-05 06:43:50

sunnieside-up
Member
Registered: 2011-08-10
Posts: 58

[SOLVED] Cannot connect to ethernet

Hi guys,

I'm having trouble connecting to my wired ethernet. I'm using networkmanager, and wireless works fine. However, it will not connect to wired connections, and when I run sudo dhcpcd eth0 I get:

dhcpcd[2044]: version 5.2.12 starting
dhcpcd[2044]: eth0: waiting for carrier
dhcpcd[2044]: timed out

Does anyone know what's going on?

Last edited by sunnieside-up (2011-09-06 03:39:06)

Offline

#2 2011-09-05 09:18:27

keen90
Member
From: Europe
Registered: 2010-04-07
Posts: 106

Re: [SOLVED] Cannot connect to ethernet

Are you sure your device is up?
You can try (as root):

ifcfg eth0 up

and the run the dhcpcd

Offline

#3 2011-09-05 13:10:00

karol
Archivist
Registered: 2009-05-06
Posts: 25,440

Re: [SOLVED] Cannot connect to ethernet

Post the output of 'ip add list'.

Offline

#4 2011-09-05 20:17:41

sunnieside-up
Member
Registered: 2011-08-10
Posts: 58

Re: [SOLVED] Cannot connect to ethernet

sudo ifcfg eth0 up:

/usr/sbin/ifcfg: line 25: [: up: integer expression expected
/usr/sbin/ifcfg: line 26: [: up: integer expression expected
/usr/sbin/ifcfg: line 27: [: up: integer expression expected
/usr/sbin/ifcfg: line 28: [: up: integer expression expected
arping: unknown host up
Error: some host already uses address up on eth0.

And dhcpcd didn't work still. What is ifcfg anyways, is it the same as ifconfig eth0 up?

ip add list:

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN 
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN qlen 1000
    link/ether 70:5a:b6:69:e7:3e brd ff:ff:ff:ff:ff:ff
    inet6 fe80::725a:b6ff:fe69:e73e/64 scope link 
       valid_lft forever preferred_lft forever
3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN qlen 1000
    link/ether 00:26:c7:17:c2:48 brd ff:ff:ff:ff:ff:ff
    inet6 fe80::226:c7ff:fe17:c248/64 scope link 
       valid_lft forever preferred_lft forever

Offline

#5 2011-09-05 20:50:34

moetunes
Member
From: A comfortable couch
Registered: 2010-10-09
Posts: 1,033

Re: [SOLVED] Cannot connect to ethernet

Why are you using dhcpd? If you're connecting to a router it will have its' own dhcp daemon.

You're just jealous because the voices only talk to me.

Offline

#6 2011-09-05 23:22:04

ewaller
Administrator
From: Pasadena, CA
Registered: 2009-07-13
Posts: 19,771

Re: [SOLVED] Cannot connect to ethernet

2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP>

Check your cable.  You won't get anywhere without a carrier.  All that usually takes is a good cable and a live port to hook it to. 
Does your NIC have a carrier and/or activity lights?  Are the lit? 
How about your router/switch/hub/modem?  Is it plugged in and turned on? Does it have anunciators? are they lit?

Nothing is too wonderful to be true, if it be consistent with the laws of nature -- Michael Faraday
Sometimes it is the people no one can imagine anything of who do the things no one can imagine. -- Alan Turing
---
How to Ask Questions the Smart Way

Offline

#7 2011-09-06 03:01:18

sunnieside-up
Member
Registered: 2011-08-10
Posts: 58

Re: [SOLVED] Cannot connect to ethernet

The cable and connectors work fine, I can connect under windows 7. It's a problem with linux somewhere. Networkmanager also tries to automatically connect, but it never works.

Offline

#8 2011-09-06 03:11:26

ewaller
Administrator
From: Pasadena, CA
Registered: 2009-07-13
Posts: 19,771

Re: [SOLVED] Cannot connect to ethernet

Fair enough.  But until you do get a carrier, don't waste your time on things like dhcpcd which operate on the higher levels of the stack.  The physical and transport layers have to be working first.  Could you post the output of lspci -vv   (That is two v's, not a w)  ??

Nothing is too wonderful to be true, if it be consistent with the laws of nature -- Michael Faraday
Sometimes it is the people no one can imagine anything of who do the things no one can imagine. -- Alan Turing
---
How to Ask Questions the Smart Way

Offline

#9 2011-09-06 03:16:33

sunnieside-up
Member
Registered: 2011-08-10
Posts: 58

Re: [SOLVED] Cannot connect to ethernet

lspci -vv:

00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 12)
	Subsystem: Lenovo Device 391e
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: <access denied>
	Kernel modules: intel-agp

00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 12) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 00005000-00005fff
	Memory behind bridge: d2000000-d30fffff
	Prefetchable memory behind bridge: 00000000c0000000-00000000d1ffffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06)
	Subsystem: Lenovo Device 38a5
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at db106100 (64-bit, non-prefetchable) [size=16]
	Capabilities: <access denied>
	Kernel driver in use: mei
	Kernel modules: mei

00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) (prog-if 20 [EHCI])
	Subsystem: Lenovo Device 38aa
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at db105c00 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ehci_hcd
	Kernel modules: ehci-hcd

00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05)
	Subsystem: Lenovo Device 38af
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 43
	Region 0: Memory at db100000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: HDA Intel
	Kernel modules: snd-hda-intel

00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=02, subordinate=05, sec-latency=0
	I/O behind bridge: 00004000-00004fff
	Memory behind bridge: da100000-db0fffff
	Prefetchable memory behind bridge: 00000000d3100000-00000000d40fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
	I/O behind bridge: 00003000-00003fff
	Memory behind bridge: d9100000-da0fffff
	Prefetchable memory behind bridge: 00000000d4100000-00000000d50fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:1c.2 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 (rev 05) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
	I/O behind bridge: 00002000-00002fff
	Memory behind bridge: d8100000-d90fffff
	Prefetchable memory behind bridge: 00000000d5100000-00000000d60fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:1c.4 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 5 (rev 05) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=08, subordinate=0b, sec-latency=0
	I/O behind bridge: 00001000-00001fff
	Memory behind bridge: d7100000-d80fffff
	Prefetchable memory behind bridge: 00000000d6100000-00000000d70fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) (prog-if 20 [EHCI])
	Subsystem: Lenovo Device 38b8
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 23
	Region 0: Memory at db105800 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ehci_hcd
	Kernel modules: ehci-hcd

00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5) (prog-if 01 [Subtractive decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Bus: primary=00, secondary=0c, subordinate=0c, sec-latency=32
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>

00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05)
	Subsystem: Lenovo Device 38be
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: <access denied>
	Kernel modules: iTCO_wdt

00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 05) (prog-if 01 [AHCI 1.0])
	Subsystem: Lenovo Device 38c1
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 41
	Region 0: I/O ports at 6048 [size=8]
	Region 1: I/O ports at 6054 [size=4]
	Region 2: I/O ports at 6040 [size=8]
	Region 3: I/O ports at 6050 [size=4]
	Region 4: I/O ports at 6020 [size=32]
	Region 5: Memory at db105000 (32-bit, non-prefetchable) [size=2K]
	Capabilities: <access denied>
	Kernel driver in use: ahci
	Kernel modules: ahci

00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05)
	Subsystem: Lenovo Device 38bf
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin C routed to IRQ 19
	Region 0: Memory at db106000 (64-bit, non-prefetchable) [size=256]
	Region 4: I/O ports at 6000 [size=32]
	Kernel driver in use: i801_smbus
	Kernel modules: i2c-i801

00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 05)
	Subsystem: Lenovo Device 38c0
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 21
	Region 0: Memory at db104000 (64-bit, non-prefetchable) [size=4K]
	Capabilities: <access denied>
	Kernel driver in use: intel ips
	Kernel modules: intel_ips

01:00.0 VGA compatible controller: nVidia Corporation GT218 [GeForce 310M] (rev a2) (prog-if 00 [VGA controller])
	Subsystem: Lenovo Device 392d
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at d2000000 (32-bit, non-prefetchable) [size=16M]
	Region 1: Memory at c0000000 (64-bit, prefetchable) [size=256M]
	Region 3: Memory at d0000000 (64-bit, prefetchable) [size=32M]
	Region 5: I/O ports at 5000 [size=128]
	[virtual] Expansion ROM at d3080000 [disabled] [size=512K]
	Capabilities: <access denied>
	Kernel driver in use: nvidia
	Kernel modules: nvidiafb, nvidia, nouveau

01:00.1 Audio device: nVidia Corporation High Definition Audio Controller (rev a1)
	Subsystem: Lenovo Device 392d
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at d3000000 (32-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: HDA Intel
	Kernel modules: snd-hda-intel

06:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000
	Subsystem: Intel Corporation Centrino Wireless-N 1000 BGN
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 42
	Region 0: Memory at d9100000 (64-bit, non-prefetchable) [size=8K]
	Capabilities: <access denied>
	Kernel driver in use: iwlagn
	Kernel modules: iwlagn

07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02)
	Subsystem: Lenovo Device 392e
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 44
	Region 0: I/O ports at 2000 [size=256]
	Region 2: Memory at d5110000 (64-bit, prefetchable) [size=4K]
	Region 4: Memory at d5100000 (64-bit, prefetchable) [size=64K]
	Expansion ROM at d5120000 [disabled] [size=128K]
	Capabilities: <access denied>
	Kernel driver in use: r8169
	Kernel modules: r8169

ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02)
	Subsystem: Lenovo Device 392b
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0

ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02)
	Subsystem: Lenovo Device 392b
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0

ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02)
	Subsystem: Lenovo Device 392b
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0

ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02)
	Subsystem: Lenovo Device 392b
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0

ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02)
	Subsystem: Lenovo Device 392b
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0

ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02)
	Subsystem: Lenovo Device 392b
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0

Also, I have this line in my rc.conf ever since I get networkmanager, is this the right way to do it?

#eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
#eth0="dhcp"
INTERFACES=(!eth0)

Offline

#10 2011-09-06 03:24:01

lilsirecho
Veteran
Registered: 2003-10-24
Posts: 5,000

Re: [SOLVED] Cannot connect to ethernet

I suggest you remove the ! from interfaces....................

Prediction...This year will be a very odd year!
Hard work does not kill people but why risk it: Charlie Mccarthy
A man is not complete until he is married..then..he is finished.
When ALL is lost, what can be found? Even bytes get lonely for a little bit!     X-ray confirms Iam spineless!

Offline

#11 2011-09-06 03:38:39

sunnieside-up
Member
Registered: 2011-08-10
Posts: 58

Re: [SOLVED] Cannot connect to ethernet

Yeah that worked! Thanks for all your guys' help! Although I am a bit confused because the arch wiki told me to put !eth0, but oh well I'm not complaining

Offline

Pages: 1

Board footer

Powered by FluxBB