You are not logged in.

#1 2012-04-11 22:58:30

aardwolf
Member
From: Belgium
Registered: 2005-07-23
Posts: 310

VMware "rc.d start vmware" says "failed" to most steps

Hello,

The wiki says that to get modules like "vmmon" loaded, it should load that, and more, by running  rc.start vmware.

However, for me running that (as root) gives this instead (with failed next to most things):

rc.d start vmware
Starting VMware services:
   Virtual machine monitor                                            failed
   Virtual machine communication interface                            failed
   VM communication interface socket family                           failed
   Blocking file system                                                done
   Virtual ethernet                                                   failed
   VMware Authentication Daemon                                        done

And the modules are still nog loaded.

My linux is 3.2.13-1-ARCH x86_64
And VMware player is version 4.0.2 build-591240

I followed the wiki to install it: https://wiki.archlinux.org/index.php/VMware

I did all of "Installation"
of "Configuration", I only did the "sed -i "s|/sbin/|/usr/bin/|g" /usr/bin/vmplayer"
Of "VMware module patches and installation", I did the steps for kernel 3.2/3.3, with vmware802fixlinux320.tar.gz

What could be the problem?

Thanks!

Last edited by aardwolf (2012-04-11 23:01:52)

Offline

#2 2012-04-11 23:10:03

karabaja4
Member
From: Croatia
Registered: 2008-09-14
Posts: 1,049
Website

Re: VMware "rc.d start vmware" says "failed" to most steps

You need to rebuild the modules after patching:

sudo vmware-modconfig --console --install-all

Offline

#3 2012-04-12 07:52:13

aardwolf
Member
From: Belgium
Registered: 2005-07-23
Posts: 310

Re: VMware "rc.d start vmware" says "failed" to most steps

karabaja4 wrote:

You need to rebuild the modules after patching:

sudo vmware-modconfig --console --install-all

That didn't solve it, at the end of all the output of this command, it even also tried to do the same and output the same thing again:

Starting VMware services:
   Virtual machine monitor                                            failed
   Virtual machine communication interface                            failed
   VM communication interface socket family                           failed
   Blocking file system                                                done
   Virtual ethernet                                                   failed
   VMware Authentication Daemon                                        done


If I run modprobe vmmon and modprobe vmci manually, then VMware player works, but there's no network... even after doing modprobe vmnet and modprobe vsock.

I hate this so frigging much, both VMware and Virtualbox are so fragile! Why doesn't there exist a PC emulator that doesn't depend on kernel versions and so on! NES emulators can, why not a PC emulator that has 3D graphics! What more than graphics, sound, network, mouse and keyboard do you need, all of which can work without depending on a kernel version (except for reliable and well supported modules like the 3D graphics)!

Last edited by aardwolf (2012-04-12 10:13:27)

Offline

#4 2012-04-17 15:04:40

phyte
Member
Registered: 2012-03-27
Posts: 17

Re: VMware "rc.d start vmware" says "failed" to most steps

You may want to try vmware-patch.
After installing, try (as root!):

vmware-patch

It will patch the necessary source files. Then you can use the vmware-modconfig command.
I use VMware Workstation 8 and 3.3.1-1 kernel atm and this AUR package is incredibly helpfull.

But remember, after every kernel upgrade, you need to rerun the vmware-patch command and to compile the modules again.


Sometimes, in order to see the light, you have to risk the dark

Offline

Board footer

Powered by FluxBB