You are not logged in.
- Topics: Active | Unanswered
#1 2012-05-04 17:59:09
- spiky25
- Member
- Registered: 2009-09-29
- Posts: 134
[wifi] bcm4313 troubles with linux-lqx 3.3.4-2
The free driver and firmware seem breaking at each upgrade, broadcom-wl don't seem to be updated fast enough, what I could do to keep my wifi working while keeping the rolling release way active, change my wireless chip or there's a fix ?
English isn't my native langage
Offline
#2 2012-05-04 18:29:02
- Gusar
- Member
- Registered: 2009-08-25
- Posts: 3,605
Re: [wifi] bcm4313 troubles with linux-lqx 3.3.4-2
It would help if you'd provide a bit more info. A very possible scenario, you have bcma blacklisted. If that's not it, like I said, provide more info. "It doesn't work" is not enough to get help.
Offline
#3 2012-05-04 20:43:49
- spiky25
- Member
- Registered: 2009-09-29
- Posts: 134
Re: [wifi] bcm4313 troubles with linux-lqx 3.3.4-2
modprobe. conf
alias floppy off
blacklist fd0
blacklist floppy
blacklist ipv6
blacklist pcspkr
blacklist snd_pcsp
lspci
02:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01)
*using wlan0 normaly, invisible by iwconfig/ifconfig ...*
English isn't my native langage
Offline
#4 2012-05-04 22:30:29
- spiky25
- Member
- Registered: 2009-09-29
- Posts: 134
Re: [wifi] bcm4313 troubles with linux-lqx 3.3.4-2
I removed two other .conf, both blacklisting bcma, but now it work but don't connect to my other laptop in AP mode ...
English isn't my native langage
Offline
#5 2012-05-04 22:41:58
- spiky25
- Member
- Registered: 2009-09-29
- Posts: 134
Re: [wifi] bcm4313 troubles with linux-lqx 3.3.4-2
English isn't my native langage
Offline
#6 2012-05-04 23:08:56
- Gusar
- Member
- Registered: 2009-08-25
- Posts: 3,605
Re: [wifi] bcm4313 troubles with linux-lqx 3.3.4-2
Full dmesg output would be nice to have. Those two lines I've seen before, however I don't know if they're actual errors or just informational output.
Also, exact commands you used to try to connect.
Offline
#7 2012-05-05 02:58:33
- spiky25
- Member
- Registered: 2009-09-29
- Posts: 134
Re: [wifi] bcm4313 troubles with linux-lqx 3.3.4-2
I use network-manager so I don't know the command lines used ...
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.3.4-2-ARCH (tobias@T-POWA-LX) (gcc version 4.7.0 20120414 (prerelease) (GCC) ) #1 SMP PREEMPT Wed May 2 18:28:42 CEST 2012
[ 0.000000] Command line: root=/dev/disk/by-uuid/f2329a91-cec6-4e92-9258-1b518a345feb loglevel=3 ro quiet resume=/dev/disk/by-uuid/962f6818-35c4-43cc-9d88-f4205b2021ee
[ 0.000000] Disabled fast string operations
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007f494000 (usable)
[ 0.000000] BIOS-e820: 000000007f494000 - 000000007f4bf000 (reserved)
[ 0.000000] BIOS-e820: 000000007f4bf000 - 000000007f579000 (usable)
[ 0.000000] BIOS-e820: 000000007f579000 - 000000007f5bf000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007f5bf000 - 000000007f5ec000 (usable)
[ 0.000000] BIOS-e820: 000000007f5ec000 - 000000007f5ff000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007f5ff000 - 000000007f600000 (usable)
[ 0.000000] BIOS-e820: 000000007f600000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI 2.6 present.
[ 0.000000] DMI: eMachines eM350/eM350, BIOS V1.06 07/08/2010
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] No AGP bridge found
[ 0.000000] last_pfn = 0x7f600 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-DFFFF write-through
[ 0.000000] E0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0FFF00000 mask 0FFF00000 write-protect
[ 0.000000] 1 base 000000000 mask 0C0000000 write-back
[ 0.000000] 2 base 040000000 mask 0C0000000 write-back
[ 0.000000] 3 base 07F800000 mask 0FF800000 uncachable
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] Base memory trampoline at [ffff88000009a000] 9a000 size 20480
[ 0.000000] init_memory_mapping: 0000000000000000-000000007f600000
[ 0.000000] 0000000000 - 007f600000 page 2M
[ 0.000000] kernel direct mapping tables up to 7f600000 @ 1fffd000-20000000
[ 0.000000] RAMDISK: 37d6d000 - 37ff0000
[ 0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 ACRSYS)
[ 0.000000] ACPI: XSDT 000000007f5fe120 00064 (v01 ACRSYS ACRPRDCT 00000001 01000013)
[ 0.000000] ACPI: FACP 000000007f5fd000 000F4 (v04 ACRSYS ACRPRDCT 00000001 1025 01000013)
[ 0.000000] ACPI: DSDT 000000007f5f1000 08D35 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
[ 0.000000] ACPI: FACS 000000007f586000 00040
[ 0.000000] ACPI: HPET 000000007f5fc000 00038 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
[ 0.000000] ACPI: APIC 000000007f5fb000 00078 (v02 ACRSYS ACRPRDCT 00000001 1025 01000013)
[ 0.000000] ACPI: MCFG 000000007f5fa000 0003C (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
[ 0.000000] ACPI: SLIC 000000007f5f0000 00176 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
[ 0.000000] ACPI: BOOT 000000007f5ef000 00028 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
[ 0.000000] ACPI: SSDT 000000007f5ed000 004C4 (v02 PmRef CpuPm 00003000 INTL 20051117)
[ 0.000000] ACPI: WDAT 000000007f5ec000 00194 (v01 INSYDE INSYDE 00000001 MSFT 01000013)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-000000007f600000
[ 0.000000] Initmem setup node 0 0000000000000000-000000007f600000
[ 0.000000] NODE_DATA [000000007f5e7000 - 000000007f5ebfff]
[ 0.000000] [ffffea0000000000-ffffea0001ffffff] PMD -> [ffff88007cc00000-ffff88007ebfffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal empty
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0007f494
[ 0.000000] 0: 0x0007f4bf -> 0x0007f579
[ 0.000000] 0: 0x0007f5bf -> 0x0007f5ec
[ 0.000000] 0: 0x0007f5ff -> 0x0007f600
[ 0.000000] On node 0 totalpages: 521483
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 5 pages reserved
[ 0.000000] DMA zone: 3914 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 8088 pages used for memmap
[ 0.000000] DMA32 zone: 509412 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 000000007f494000 - 000000007f4bf000
[ 0.000000] PM: Registered nosave memory: 000000007f579000 - 000000007f5bf000
[ 0.000000] PM: Registered nosave memory: 000000007f5ec000 - 000000007f5ff000
[ 0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:60000000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff88007f200000 s82176 r8192 d24320 u524288
[ 0.000000] pcpu-alloc: s82176 r8192 d24320 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 513326
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: root=/dev/disk/by-uuid/f2329a91-cec6-4e92-9258-1b518a345feb loglevel=3 ro quiet resume=/dev/disk/by-uuid/962f6818-35c4-43cc-9d88-f4205b2021ee
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 2038988k/2086912k available (4495k kernel code, 980k absent, 46944k reserved, 4327k data, 732k init)
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:4352 nr_irqs:712 16
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 8388608 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1662.663 MHz processor.
[ 0.003340] Calibrating delay loop (skipped), value calculated using timer frequency.. 3326.88 BogoMIPS (lpj=5542210)
[ 0.003351] pid_max: default: 32768 minimum: 301
[ 0.003419] Security Framework initialized
[ 0.003429] AppArmor: AppArmor disabled by boot time parameter
[ 0.003880] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.005777] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.007436] Mount-cache hash table entries: 256
[ 0.007798] Initializing cgroup subsys cpuacct
[ 0.007808] Initializing cgroup subsys memory
[ 0.007829] Initializing cgroup subsys devices
[ 0.007835] Initializing cgroup subsys freezer
[ 0.007841] Initializing cgroup subsys net_cls
[ 0.007846] Initializing cgroup subsys blkio
[ 0.007922] Disabled fast string operations
[ 0.007932] CPU: Physical Processor ID: 0
[ 0.007936] CPU: Processor Core ID: 0
[ 0.007941] mce: CPU supports 5 MCE banks
[ 0.007954] CPU0: Thermal monitoring handled by SMI
[ 0.007962] using mwait in idle threads.
[ 0.009358] ACPI: Core revision 20120111
[ 0.026713] ftrace: allocating 17484 entries in 69 pages
[ 0.037288] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.073073] CPU0: Intel(R) Atom(TM) CPU N450 @ 1.66GHz stepping 0a
[ 0.073329] Performance Events: PEBS fmt0+, Atom events, Intel PMU driver.
[ 0.073329] ... version: 3
[ 0.073329] ... bit width: 40
[ 0.073329] ... generic registers: 2
[ 0.073329] ... value mask: 000000ffffffffff
[ 0.073329] ... max period: 000000007fffffff
[ 0.073329] ... fixed-purpose events: 3
[ 0.073329] ... event mask: 0000000700000003
[ 0.090218] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.116704] Booting Node 0, Processors #1
[ 0.116711] smpboot cpu 1: start_ip = 9a000
[ 0.006666] Disabled fast string operations
[ 0.006666] CPU1: Thermal monitoring handled by SMI
[ 0.130069] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.136672] Brought up 2 CPUs
[ 0.136680] Total of 2 processors activated (6653.76 BogoMIPS).
[ 0.137231] devtmpfs: initialized
[ 0.141864] PM: Registering ACPI NVS region at 7f579000 (286720 bytes)
[ 0.142457] NET: Registered protocol family 16
[ 0.143494] ACPI: bus type pci registered
[ 0.143679] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.143688] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 0.204076] PCI: Using configuration type 1 for base access
[ 0.206724] bio: create slab <bio-0> at 0
[ 0.206780] ACPI: Added _OSI(Module Device)
[ 0.206780] ACPI: Added _OSI(Processor Device)
[ 0.206780] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.206783] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.211003] ACPI: EC: Look up EC in DSDT
[ 0.215214] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.219278] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.220340] ACPI: SSDT 000000007f4b7c90 001F7 (v02 PmRef Cpu0Ist 00003000 INTL 20051117)
[ 0.221336] ACPI: Dynamic OEM Table Load:
[ 0.221344] ACPI: SSDT (null) 001F7 (v02 PmRef Cpu0Ist 00003000 INTL 20051117)
[ 0.221658] ACPI: SSDT 000000007f4b6e10 001C7 (v02 PmRef Cpu0Cst 00003001 INTL 20051117)
[ 0.222602] ACPI: Dynamic OEM Table Load:
[ 0.222610] ACPI: SSDT (null) 001C7 (v02 PmRef Cpu0Cst 00003001 INTL 20051117)
[ 0.223400] ACPI: SSDT 000000007f4b7f10 000D0 (v02 PmRef Cpu1Ist 00003000 INTL 20051117)
[ 0.224369] ACPI: Dynamic OEM Table Load:
[ 0.224377] ACPI: SSDT (null) 000D0 (v02 PmRef Cpu1Ist 00003000 INTL 20051117)
[ 0.224672] ACPI: SSDT 000000007f4b5f10 00083 (v02 PmRef Cpu1Cst 00003000 INTL 20051117)
[ 0.225621] ACPI: Dynamic OEM Table Load:
[ 0.225628] ACPI: SSDT (null) 00083 (v02 PmRef Cpu1Cst 00003000 INTL 20051117)
[ 0.226855] ACPI: Interpreter enabled
[ 0.226866] ACPI: (supports S0 S3 S4 S5)
[ 0.226933] ACPI: Using IOAPIC for interrupt routing
[ 0.358800] ACPI: Power Resource [FN00] (on)
[ 0.359744] ACPI: EC: GPE = 0x19, I/O: command/status = 0x66, data = 0x62
[ 0.360171] ACPI: No dock devices found.
[ 0.360182] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.361140] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20120111/nspredef-359)
[ 0.361159] \_SB_.PCI0:_OSC evaluation returned wrong type
[ 0.361163] _OSC request data:1 8 1f
[ 0.361176] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.362705] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
[ 0.362713] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
[ 0.362719] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 0.362727] pci_root PNP0A08:00: host bridge window [mem 0x80000000-0xfebfffff]
[ 0.362834] PCI host bridge to bus 0000:00
[ 0.362841] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 0.362847] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 0.362853] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.362859] pci_bus 0000:00: root bus resource [mem 0x80000000-0xfebfffff]
[ 0.362878] pci 0000:00:00.0: [8086:a010] type 0 class 0x000600
[ 0.362946] pci 0000:00:02.0: [8086:a011] type 0 class 0x000300
[ 0.362963] pci 0000:00:02.0: reg 10: [mem 0x94180000-0x941fffff]
[ 0.362973] pci 0000:00:02.0: reg 14: [io 0x40c0-0x40c7]
[ 0.362983] pci 0000:00:02.0: reg 18: [mem 0x80000000-0x8fffffff pref]
[ 0.362993] pci 0000:00:02.0: reg 1c: [mem 0x94000000-0x940fffff]
[ 0.363044] pci 0000:00:02.1: [8086:a012] type 0 class 0x000380
[ 0.363058] pci 0000:00:02.1: reg 10: [mem 0x94100000-0x9417ffff]
[ 0.363180] pci 0000:00:1b.0: [8086:27d8] type 0 class 0x000403
[ 0.363211] pci 0000:00:1b.0: reg 10: [mem 0x94200000-0x94203fff 64bit]
[ 0.363360] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.363408] pci 0000:00:1c.0: [8086:27d0] type 1 class 0x000604
[ 0.363540] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.363589] pci 0000:00:1c.1: [8086:27d2] type 1 class 0x000604
[ 0.363720] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.363772] pci 0000:00:1d.0: [8086:27c8] type 0 class 0x000c03
[ 0.363841] pci 0000:00:1d.0: reg 20: [io 0x4080-0x409f]
[ 0.363900] pci 0000:00:1d.1: [8086:27c9] type 0 class 0x000c03
[ 0.363969] pci 0000:00:1d.1: reg 20: [io 0x4060-0x407f]
[ 0.364027] pci 0000:00:1d.2: [8086:27ca] type 0 class 0x000c03
[ 0.364096] pci 0000:00:1d.2: reg 20: [io 0x4040-0x405f]
[ 0.364160] pci 0000:00:1d.3: [8086:27cb] type 0 class 0x000c03
[ 0.364229] pci 0000:00:1d.3: reg 20: [io 0x4020-0x403f]
[ 0.364302] pci 0000:00:1d.7: [8086:27cc] type 0 class 0x000c03
[ 0.364334] pci 0000:00:1d.7: reg 10: [mem 0x94204400-0x942047ff]
[ 0.364461] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.364499] pci 0000:00:1e.0: [8086:2448] type 1 class 0x000604
[ 0.364620] pci 0000:00:1f.0: [8086:27bc] type 0 class 0x000601
[ 0.364788] pci 0000:00:1f.2: [8086:27c1] type 0 class 0x000106
[ 0.364819] pci 0000:00:1f.2: reg 10: [io 0x40b8-0x40bf]
[ 0.364836] pci 0000:00:1f.2: reg 14: [io 0x40cc-0x40cf]
[ 0.364852] pci 0000:00:1f.2: reg 18: [io 0x40b0-0x40b7]
[ 0.364869] pci 0000:00:1f.2: reg 1c: [io 0x40c8-0x40cb]
[ 0.364886] pci 0000:00:1f.2: reg 20: [io 0x40a0-0x40af]
[ 0.364903] pci 0000:00:1f.2: reg 24: [mem 0x94204000-0x942043ff]
[ 0.364973] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.365006] pci 0000:00:1f.3: [8086:27da] type 0 class 0x000c05
[ 0.365075] pci 0000:00:1f.3: reg 20: [io 0x4000-0x401f]
[ 0.365228] pci 0000:01:00.0: [1969:1062] type 0 class 0x000200
[ 0.365267] pci 0000:01:00.0: reg 10: [mem 0x93000000-0x9303ffff 64bit]
[ 0.365288] pci 0000:01:00.0: reg 18: [io 0x3000-0x307f]
[ 0.365447] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.370014] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[ 0.370024] pci 0000:00:1c.0: bridge window [io 0x3000-0x3fff]
[ 0.370033] pci 0000:00:1c.0: bridge window [mem 0x93000000-0x93ffffff]
[ 0.370046] pci 0000:00:1c.0: bridge window [mem 0x90000000-0x90ffffff 64bit pref]
[ 0.370199] pci 0000:02:00.0: [14e4:4727] type 0 class 0x000280
[ 0.370250] pci 0000:02:00.0: reg 10: [mem 0x92000000-0x92003fff 64bit]
[ 0.370502] pci 0000:02:00.0: supports D1 D2
[ 0.370507] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 0.370614] pci 0000:00:1c.1: PCI bridge to [bus 02-02]
[ 0.370624] pci 0000:00:1c.1: bridge window [io 0x2000-0x2fff]
[ 0.370633] pci 0000:00:1c.1: bridge window [mem 0x92000000-0x92ffffff]
[ 0.370645] pci 0000:00:1c.1: bridge window [mem 0x91000000-0x91ffffff 64bit pref]
[ 0.370745] pci 0000:00:1e.0: PCI bridge to [bus 03-03] (subtractive decode)
[ 0.370765] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 0.370772] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 0.370778] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.370785] pci 0000:00:1e.0: bridge window [mem 0x80000000-0xfebfffff] (subtractive decode)
[ 0.370820] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.371166] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
[ 0.371309] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT]
[ 0.371630] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20120111/nspredef-359)
[ 0.371650] \_SB_.PCI0:_OSC evaluation returned wrong type
[ 0.371654] _OSC request data:1 1f 1f
[ 0.371665] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 0.371807] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20120111/nspredef-359)
[ 0.371824] \_SB_.PCI0:_OSC evaluation returned wrong type
[ 0.371828] _OSC request data:1 0 1d
[ 0.371839] pci0000:00: ACPI _OSC request failed (AE_TYPE), returned control mask: 0x1d
[ 0.371843] ACPI _OSC control for PCIe not granted, disabling ASPM
[ 0.379122] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.379282] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 *10 11 12)
[ 0.379435] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.379588] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.379740] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.379895] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.380069] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.380224] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.380417] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.380417] vgaarb: loaded
[ 0.380417] vgaarb: bridge control possible 0000:00:02.0
[ 0.380417] PCI: Using ACPI for IRQ routing
[ 0.390738] PCI: pci_cache_line_size set to 64 bytes
[ 0.390888] reserve RAM buffer: 000000000009fc00 - 000000000009ffff
[ 0.390894] reserve RAM buffer: 000000007f494000 - 000000007fffffff
[ 0.390901] reserve RAM buffer: 000000007f579000 - 000000007fffffff
[ 0.390907] reserve RAM buffer: 000000007f5ec000 - 000000007fffffff
[ 0.390913] reserve RAM buffer: 000000007f600000 - 000000007fffffff
[ 0.391186] NetLabel: Initializing
[ 0.391191] NetLabel: domain hash size = 128
[ 0.391195] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.391230] NetLabel: unlabeled traffic allowed by default
[ 0.391241] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.391251] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.391261] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.400008] Switching to clocksource hpet
[ 0.419610] pnp: PnP ACPI init
[ 0.419654] ACPI: bus type pnp registered
[ 0.420579] pnp 00:00: [bus 00-ff]
[ 0.420587] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.420593] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.420598] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.420604] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.420610] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[ 0.420616] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[ 0.420621] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[ 0.420627] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[ 0.420633] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[ 0.420638] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[ 0.420644] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[ 0.420650] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[ 0.420655] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[ 0.420661] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[ 0.420667] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[ 0.420672] pnp 00:00: [mem 0x000ec000-0x000effff window]
[ 0.420678] pnp 00:00: [mem 0x000f0000-0x000fffff window]
[ 0.420684] pnp 00:00: [mem 0x80000000-0xfebfffff window]
[ 0.420830] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 0.480367] pnp 00:01: [io 0x0068]
[ 0.480374] pnp 00:01: [io 0x006c]
[ 0.480380] pnp 00:01: [io 0x164e-0x164f]
[ 0.480384] pnp 00:01: [io 0x0061]
[ 0.480395] pnp 00:01: [io 0x0070]
[ 0.480400] pnp 00:01: [io 0x0080]
[ 0.480404] pnp 00:01: [io 0x0092]
[ 0.480409] pnp 00:01: [io 0x00b2-0x00b3]
[ 0.480414] pnp 00:01: [io 0x0063]
[ 0.480419] pnp 00:01: [io 0x0065]
[ 0.480423] pnp 00:01: [io 0x0067]
[ 0.480428] pnp 00:01: [io 0x0600-0x060f]
[ 0.480433] pnp 00:01: [io 0x0610]
[ 0.480437] pnp 00:01: [io 0x0800-0x080f]
[ 0.480442] pnp 00:01: [io 0x0810-0x0817]
[ 0.480447] pnp 00:01: [io 0x0400-0x047f]
[ 0.480452] pnp 00:01: [io 0x0500-0x053f]
[ 0.480457] pnp 00:01: [io 0xff2c-0xff2f]
[ 0.480462] pnp 00:01: [mem 0xe0000000-0xefffffff]
[ 0.480468] pnp 00:01: [mem 0xfed1c000-0xfed1ffff]
[ 0.480473] pnp 00:01: [mem 0xfed14000-0xfed17fff]
[ 0.480478] pnp 00:01: [mem 0xfed18000-0xfed18fff]
[ 0.480483] pnp 00:01: [mem 0xfed19000-0xfed19fff]
[ 0.480489] pnp 00:01: [mem 0xfec00000-0xfec00fff]
[ 0.480494] pnp 00:01: [mem 0xfee00000-0xfee00fff]
[ 0.480660] system 00:01: [io 0x164e-0x164f] has been reserved
[ 0.480670] system 00:01: [io 0x0600-0x060f] has been reserved
[ 0.480676] system 00:01: [io 0x0610] has been reserved
[ 0.480683] system 00:01: [io 0x0800-0x080f] has been reserved
[ 0.480689] system 00:01: [io 0x0810-0x0817] has been reserved
[ 0.480696] system 00:01: [io 0x0400-0x047f] has been reserved
[ 0.480703] system 00:01: [io 0x0500-0x053f] has been reserved
[ 0.480710] system 00:01: [io 0xff2c-0xff2f] has been reserved
[ 0.480718] system 00:01: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.480725] system 00:01: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.480732] system 00:01: [mem 0xfed14000-0xfed17fff] has been reserved
[ 0.480739] system 00:01: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.480746] system 00:01: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.480754] system 00:01: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.480761] system 00:01: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.480771] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.480803] pnp 00:02: [io 0x0000-0x001f]
[ 0.480809] pnp 00:02: [io 0x0081-0x0091]
[ 0.480814] pnp 00:02: [io 0x0093-0x009f]
[ 0.480819] pnp 00:02: [io 0x00c0-0x00df]
[ 0.480825] pnp 00:02: [dma 4]
[ 0.480894] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.480963] pnp 00:03: [io 0x0070-0x0077]
[ 0.481040] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.481207] pnp 00:04: [irq 0 disabled]
[ 0.481230] pnp 00:04: [irq 8]
[ 0.481235] pnp 00:04: [mem 0xfed00000-0xfed003ff]
[ 0.481313] pnp 00:04: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.481346] pnp 00:05: [io 0x00f0]
[ 0.481360] pnp 00:05: [irq 13]
[ 0.481431] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.481463] pnp 00:06: [mem 0xff800000-0xffffffff]
[ 0.481539] pnp 00:06: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.481638] pnp 00:07: [io 0x0060]
[ 0.481644] pnp 00:07: [io 0x0064]
[ 0.481658] pnp 00:07: [irq 1]
[ 0.481740] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.481871] pnp 00:08: [irq 12]
[ 0.481950] pnp 00:08: Plug and Play ACPI device, IDs SYN1b1c SYN1b00 SYN0002 PNP0f13 (active)
[ 0.482306] pnp: PnP ACPI: found 9 devices
[ 0.482312] ACPI: ACPI bus type pnp unregistered
[ 0.494054] PCI: max bus depth: 1 pci_try_num: 2
[ 0.494116] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[ 0.494126] pci 0000:00:1c.0: bridge window [io 0x3000-0x3fff]
[ 0.494137] pci 0000:00:1c.0: bridge window [mem 0x93000000-0x93ffffff]
[ 0.494147] pci 0000:00:1c.0: bridge window [mem 0x90000000-0x90ffffff 64bit pref]
[ 0.494160] pci 0000:00:1c.1: PCI bridge to [bus 02-02]
[ 0.494167] pci 0000:00:1c.1: bridge window [io 0x2000-0x2fff]
[ 0.494177] pci 0000:00:1c.1: bridge window [mem 0x92000000-0x92ffffff]
[ 0.494187] pci 0000:00:1c.1: bridge window [mem 0x91000000-0x91ffffff 64bit pref]
[ 0.494200] pci 0000:00:1e.0: PCI bridge to [bus 03-03]
[ 0.494286] pci 0000:00:1e.0: setting latency timer to 64
[ 0.494296] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.494302] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.494308] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.494314] pci_bus 0000:00: resource 7 [mem 0x80000000-0xfebfffff]
[ 0.494320] pci_bus 0000:01: resource 0 [io 0x3000-0x3fff]
[ 0.494326] pci_bus 0000:01: resource 1 [mem 0x93000000-0x93ffffff]
[ 0.494332] pci_bus 0000:01: resource 2 [mem 0x90000000-0x90ffffff 64bit pref]
[ 0.494338] pci_bus 0000:02: resource 0 [io 0x2000-0x2fff]
[ 0.494344] pci_bus 0000:02: resource 1 [mem 0x92000000-0x92ffffff]
[ 0.494350] pci_bus 0000:02: resource 2 [mem 0x91000000-0x91ffffff 64bit pref]
[ 0.494357] pci_bus 0000:03: resource 4 [io 0x0000-0x0cf7]
[ 0.494363] pci_bus 0000:03: resource 5 [io 0x0d00-0xffff]
[ 0.494369] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.494375] pci_bus 0000:03: resource 7 [mem 0x80000000-0xfebfffff]
[ 0.494464] NET: Registered protocol family 2
[ 0.494694] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.496372] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.499357] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.500087] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.500094] TCP reno registered
[ 0.500130] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.500170] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.500411] NET: Registered protocol family 1
[ 0.500450] pci 0000:00:02.0: Boot video device
[ 0.500843] PCI: CLS 64 bytes, default 64
[ 0.500990] Unpacking initramfs...
[ 0.619152] Freeing initrd memory: 2572k freed
[ 0.621119] Simple Boot Flag at 0x44 set to 0x1
[ 0.622196] audit: initializing netlink socket (disabled)
[ 0.622223] type=2000 audit(1336170050.619:1): initialized
[ 0.623054] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.628208] VFS: Disk quotas dquot_6.5.2
[ 0.628354] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.628592] msgmni has been set to 3987
[ 0.629191] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.629275] io scheduler noop registered
[ 0.629282] io scheduler deadline registered
[ 0.629467] io scheduler cfq registered (default)
[ 0.629768] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
[ 0.629982] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X
[ 0.630423] intel_idle: MWAIT substates: 0x20220
[ 0.630449] intel_idle: v0.4 model 0x1C
[ 0.630456] intel_idle: lapic_timer_reliable_states 0x2
[ 0.630463] Marking TSC unstable due to TSC halts in idle states deeper than C2
[ 0.630565] GHES: HEST is not enabled!
[ 0.630785] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.632024] Linux agpgart interface v0.103
[ 0.632219] i8042: PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSS0] at 0x60,0x64 irq 1,12
[ 0.646644] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.646758] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.647103] mousedev: PS/2 mouse device common for all mice
[ 0.647989] rtc_cmos 00:03: RTC can wake from S4
[ 0.648256] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 0.648305] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
[ 0.648429] cpuidle: using governor ladder
[ 0.648568] cpuidle: using governor menu
[ 0.649035] TCP cubic registered
[ 0.649354] NET: Registered protocol family 10
[ 0.650533] NET: Registered protocol family 17
[ 0.650553] Registering the dns_resolver key type
[ 0.651027] PM: Checking hibernation image partition /dev/disk/by-uuid/962f6818-35c4-43cc-9d88-f4205b2021ee
[ 0.660589] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 0.668856] PM: Hibernation image not present or could not be loaded.
[ 0.668882] registered taskstats version 1
[ 0.669757] rtc_cmos 00:03: setting system clock to 2012-05-04 22:20:51 UTC (1336170051)
[ 0.669927] Initializing network drop monitor service
[ 0.673305] Freeing unused kernel memory: 732k freed
[ 0.673738] Write protecting the kernel read-only data: 8192k
[ 0.687134] Freeing unused kernel memory: 1632k freed
[ 0.693709] Freeing unused kernel memory: 656k freed
[ 0.716970] udevd[37]: starting version 182
[ 0.835652] SCSI subsystem initialized
[ 0.838773] usbcore: registered new interface driver usbfs
[ 0.838849] usbcore: registered new interface driver hub
[ 0.841959] usbcore: registered new device driver usb
[ 0.842752] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.842916] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 0.842929] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 0.843018] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 0.843070] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[ 0.843096] ehci_hcd 0000:00:1d.7: debug port 1
[ 0.848980] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
[ 0.849019] libata version 3.00 loaded.
[ 0.849036] ehci_hcd 0000:00:1d.7: irq 16, io mem 0x94204400
[ 0.856013] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.856923] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 0.857548] hub 1-0:1.0: USB hub found
[ 0.857570] hub 1-0:1.0: 8 ports detected
[ 0.863846] ahci 0000:00:1f.2: version 3.0
[ 0.863996] ahci 0000:00:1f.2: irq 42 for MSI/MSI-X
[ 0.864776] ahci: SSS flag set, parallel bus scan disabled
[ 0.864842] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0x3 impl SATA mode
[ 0.864855] ahci 0000:00:1f.2: flags: 64bit ncq ilck stag pm led clo pmp pio slum part
[ 0.864870] ahci 0000:00:1f.2: setting latency timer to 64
[ 0.868254] scsi0 : ahci
[ 0.869500] scsi1 : ahci
[ 0.869815] scsi2 : ahci
[ 0.875825] scsi3 : ahci
[ 0.876412] ata1: SATA max UDMA/133 abar m1024@0x94204000 port 0x94204100 irq 42
[ 0.876422] ata2: SATA max UDMA/133 abar m1024@0x94204000 port 0x94204180 irq 42
[ 0.876428] ata3: DUMMY
[ 0.876431] ata4: DUMMY
[ 0.876523] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 0.876534] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 0.876580] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 0.876657] uhci_hcd 0000:00:1d.0: irq 16, io base 0x00004080
[ 0.877980] hub 2-0:1.0: USB hub found
[ 0.878000] hub 2-0:1.0: 2 ports detected
[ 0.878305] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 0.878318] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 0.878361] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 0.878456] uhci_hcd 0000:00:1d.1: irq 17, io base 0x00004060
[ 0.879399] hub 3-0:1.0: USB hub found
[ 0.879419] hub 3-0:1.0: 2 ports detected
[ 0.879720] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 0.879735] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 0.879776] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 0.879874] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00004040
[ 0.881290] hub 4-0:1.0: USB hub found
[ 0.881318] hub 4-0:1.0: 2 ports detected
[ 0.883479] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 0.883492] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 0.883534] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 0.883623] uhci_hcd 0000:00:1d.3: irq 19, io base 0x00004020
[ 0.884268] hub 5-0:1.0: USB hub found
[ 0.884297] hub 5-0:1.0: 2 ports detected
[ 1.163473] usb 1-4: new high-speed USB device number 2 using ehci_hcd
[ 1.363420] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.364201] ata1.00: unexpected _GTF length (4)
[ 1.364527] ata1.00: ATA-8: WDC WD1600BEVT-22A23T0, 01.01A01, max UDMA/133
[ 1.364543] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.365386] ata1.00: unexpected _GTF length (4)
[ 1.365696] ata1.00: configured for UDMA/133
[ 1.366021] scsi 0:0:0:0: Direct-Access ATA WDC WD1600BEVT-2 01.0 PQ: 0 ANSI: 5
[ 1.683480] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.696619] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 1.696929] sd 0:0:0:0: [sda] Write Protect is off
[ 1.696942] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.697058] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.748747] sda: sda1 sda2 sda3
[ 1.750090] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.265323] PM: Starting manual resume from disk
[ 2.265332] PM: Hibernation image partition 8:1 present
[ 2.265336] PM: Looking for hibernation image.
[ 2.265696] PM: Image not found (code -22)
[ 2.265703] PM: Hibernation image not present or could not be loaded.
[ 2.407124] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 4.392808] udevd[125]: starting version 182
[ 5.131091] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 5.131112] ACPI: Power Button [PWRB]
[ 5.131314] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2
[ 5.131332] ACPI: Sleep Button [SLPB]
[ 5.131539] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input3
[ 5.131627] ACPI: Lid Switch [LID0]
[ 5.131857] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 5.131875] ACPI: Power Button [PWRF]
[ 5.144820] wmi: Mapper loaded
[ 5.167783] iTCO_vendor_support: vendor-support=0
[ 5.171211] lib80211: common routines for IEEE802.11 drivers
[ 5.171222] lib80211_crypt: registered algorithm 'NULL'
[ 5.188364] thermal LNXTHERM:00: registered as thermal_zone0
[ 5.188375] ACPI: Thermal Zone [THRM] (48 C)
[ 5.201326] ACPI: Fan [FAN] (on)
[ 5.272145] Linux media interface: v0.10
[ 5.282638] atl1c 0000:01:00.0: version 1.0.1.0-NAPI
[ 5.693632] ACPI: Battery Slot [BAT0] (battery present)
[ 5.741563] acer_wmi: Acer Laptop ACPI-WMI Extras
[ 5.741605] acer_wmi: Function bitmap for Communication Button: 0x1
[ 5.741854] acer_wmi: Brightness must be controlled by generic video driver
[ 5.744494] input: Acer WMI hotkeys as /devices/virtual/input/input5
[ 5.776660] cfg80211: Calling CRDA to update world regulatory domain
[ 5.813624] ACPI: AC Adapter [AC] (on-line)
[ 5.827521] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[ 5.827772] iTCO_wdt: Found a NM10 TCO device (Version=2, TCOBASE=0x0460)
[ 5.827990] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 5.859992] Linux video capture interface: v2.00
[ 5.976482] [drm] Initialized drm 1.1.0 20060810
[ 5.976527] agpgart-intel 0000:00:00.0: Intel GMA3150 Chipset
[ 5.976835] agpgart-intel 0000:00:00.0: detected gtt size: 524288K total, 262144K mappable
[ 5.977111] agpgart-intel 0000:00:00.0: detected 8192K stolen memory
[ 5.977626] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0x80000000
[ 6.065234] wl: module license 'Mixed/Proprietary' taints kernel.
[ 6.065245] Disabling lock debugging due to kernel taint
[ 6.075657] wl: disagrees about version of symbol skb_put
[ 6.075671] wl: Unknown symbol skb_put (err -22)
[ 6.075720] wl: disagrees about version of symbol cfg80211_scan_done
[ 6.075730] wl: Unknown symbol cfg80211_scan_done (err -22)
[ 6.075742] wl: disagrees about version of symbol consume_skb
[ 6.075750] wl: Unknown symbol consume_skb (err -22)
[ 6.075769] wl: disagrees about version of symbol __netif_schedule
[ 6.075777] wl: Unknown symbol __netif_schedule (err -22)
[ 6.075790] wl: disagrees about version of symbol unregister_netdev
[ 6.075798] wl: Unknown symbol unregister_netdev (err -22)
[ 6.075888] wl: disagrees about version of symbol cfg80211_disconnected
[ 6.075898] wl: Unknown symbol cfg80211_disconnected (err -22)
[ 6.075910] wl: disagrees about version of symbol ether_setup
[ 6.075917] wl: Unknown symbol ether_setup (err -22)
[ 6.075932] wl: disagrees about version of symbol wake_up_process
[ 6.075940] wl: Unknown symbol wake_up_process (err -22)
[ 6.075953] wl: disagrees about version of symbol eth_type_trans
[ 6.075960] wl: Unknown symbol eth_type_trans (err -22)
[ 6.075973] wl: disagrees about version of symbol alloc_netdev_mqs
[ 6.075980] wl: Unknown symbol alloc_netdev_mqs (err -22)
[ 6.076031] wl: disagrees about version of symbol wiphy_register
[ 6.076039] wl: Unknown symbol wiphy_register (err -22)
[ 6.076062] wl: disagrees about version of symbol wiphy_new
[ 6.076069] wl: Unknown symbol wiphy_new (err -22)
[ 6.076107] wl: disagrees about version of symbol cfg80211_roamed
[ 6.076115] wl: Unknown symbol cfg80211_roamed (err -22)
[ 6.076163] wl: disagrees about version of symbol lib80211_get_crypto_ops
[ 6.076170] wl: Unknown symbol lib80211_get_crypto_ops (err -22)
[ 6.076189] wl: disagrees about version of symbol dev_kfree_skb_any
[ 6.076196] wl: Unknown symbol dev_kfree_skb_any (err -22)
[ 6.076215] snd_hda_intel 0000:00:1b.0: irq 43 for MSI/MSI-X
[ 6.076220] wl: disagrees about version of symbol cfg80211_ibss_joined
[ 6.076227] wl: Unknown symbol cfg80211_ibss_joined (err -22)
[ 6.076236] wl: disagrees about version of symbol skb_pull
[ 6.076243] wl: Unknown symbol skb_pull (err -22)
[ 6.076276] wl: disagrees about version of symbol cfg80211_michael_mic_failure
[ 6.076284] wl: Unknown symbol cfg80211_michael_mic_failure (err -22)
[ 6.076306] wl: disagrees about version of symbol cfg80211_connect_result
[ 6.076314] wl: Unknown symbol cfg80211_connect_result (err -22)
[ 6.076325] wl: disagrees about version of symbol skb_push
[ 6.076333] wl: Unknown symbol skb_push (err -22)
[ 6.076361] wl: disagrees about version of symbol register_netdev
[ 6.076385] wl: Unknown symbol register_netdev (err -22)
[ 6.076595] wl: disagrees about version of symbol wiphy_unregister
[ 6.076604] wl: Unknown symbol wiphy_unregister (err -22)
[ 6.076637] wl: disagrees about version of symbol cfg80211_get_bss
[ 6.076646] wl: Unknown symbol cfg80211_get_bss (err -22)
[ 6.076803] wl: disagrees about version of symbol dev_alloc_skb
[ 6.076812] wl: Unknown symbol dev_alloc_skb (err -22)
[ 6.076840] wl: disagrees about version of symbol __ieee80211_get_channel
[ 6.078961] wl: Unknown symbol __ieee80211_get_channel (err -22)
[ 6.078997] wl: disagrees about version of symbol netif_rx
[ 6.079005] wl: Unknown symbol netif_rx (err -22)
[ 6.079093] wl: disagrees about version of symbol skb_clone
[ 6.079100] wl: Unknown symbol skb_clone (err -22)
[ 6.079135] wl: disagrees about version of symbol cfg80211_inform_bss_frame
[ 6.079143] wl: Unknown symbol cfg80211_inform_bss_frame (err -22)
[ 6.079210] wl: disagrees about version of symbol wiphy_free
[ 6.079231] wl: Unknown symbol wiphy_free (err -22)
[ 6.101822] bcma: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x24, class 0x0)
[ 6.101856] bcma: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x18, class 0x0)
[ 6.101927] bcma: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x11, class 0x0)
[ 6.129063] bcma: Bus registered
[ 6.199101] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000
[ 6.222076] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input6
[ 6.223263] uvcvideo: Found UVC 1.00 device WebCam (0402:7675)
[ 6.228085] input: WebCam as /devices/pci0000:00/0000:00:1d.7/usb1/1-4/1-4:1.0/input/input7
[ 6.228468] usbcore: registered new interface driver uvcvideo
[ 6.228477] USB Video Class driver (1.1.1)
[ 6.240700] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 6.241077] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 6.244979] i915 0000:00:02.0: setting latency timer to 64
[ 6.268760] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input10
[ 6.359473] i915 0000:00:02.0: irq 44 for MSI/MSI-X
[ 6.359501] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 6.359506] [drm] Driver supports precise vblank timestamp query.
[ 6.359586] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 6.413433] fixme: max PWM is zero.
[ 6.561775] brcmsmac bcma0:0: mfg 4bf core 812 rev 24 class 0 irq 17
[ 6.690166] [drm] initialized overlay support
[ 6.709038] fbcon: inteldrmfb (fb0) is primary device
[ 7.123651] Console: switching to colour frame buffer device 128x37
[ 7.130427] fb0: inteldrmfb frame buffer device
[ 7.130432] drm: registered panic notifier
[ 7.430213] acpi device:25: registered as cooling_device3
[ 7.430982] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input11
[ 7.431176] ACPI: Video Device [OVGA] (multi-head: yes rom: no post: no)
[ 7.431436] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 7.512527] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 7.514123] brcms_module_init: register returned 0
[ 8.765325] EXT4-fs (sda2): re-mounted. Opts: (null)
[ 9.037412] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[ 9.168834] Adding 2099196k swap on /dev/sda1. Priority:-1 extents:1 across:2099196k
[ 14.109272] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.301939] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 14.522766] atl1c 0000:01:00.0: irq 45 for MSI/MSI-X
[ 14.577905] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 14.638824] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 14.641269] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 14.645320] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 32.476358] fuse init (API version 7.18)
[ 42.416481] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 42.416510] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 42.418024] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 52.478743] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 52.478762] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 52.479761] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 62.539106] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 62.539127] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 62.540172] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 71.070519] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 71.070540] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 71.071509] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 81.129707] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 81.129727] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 81.130838] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 91.189309] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 91.189330] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 91.190441] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 99.071506] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 99.071526] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 99.072495] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 109.128724] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 109.128745] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 109.129712] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 119.185743] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 119.185765] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 119.186820] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 127.071952] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 127.071973] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 127.072937] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 137.127267] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 137.127288] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 137.128258] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 147.182742] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 147.182763] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 147.183915] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 304.764916] atl1c 0000:01:00.0: atl1c: eth0 NIC Link is Up<100 Mbps Full Duplex>
[ 304.765644] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 355.320399] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 355.320421] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 355.321405] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 364.657081] atl1c 0000:01:00.0: atl1c: eth0 NIC Link is Down
[ 365.373642] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 365.373663] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 365.374615] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 375.427022] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 375.427043] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 375.428016] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 453.890502] EXT4-fs (sda2): re-mounted. Opts: commit=0
[ 454.001056] EXT4-fs (sda3): re-mounted. Opts: commit=0
[ 531.237925] atl1c 0000:01:00.0: atl1c: eth0 NIC Link is Up<100 Mbps Full Duplex>
[ 535.061015] atl1c 0000:01:00.0: irq 45 for MSI/MSI-X
[ 535.061133] atl1c 0000:01:00.0: atl1c: eth0 NIC Link is Up<100 Mbps Full Duplex>
[ 535.115590] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 535.115612] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 535.116535] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 536.856668] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 536.856689] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 536.857664] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 546.911331] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 546.911352] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 546.912326] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 556.965540] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 556.965560] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 556.966562] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 565.075796] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 565.075816] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 565.077091] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 575.139328] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 575.139348] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 575.140545] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 585.205035] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 585.205055] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 585.206040] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 593.082167] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 593.082195] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 593.083723] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 603.163160] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 603.163188] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 603.164695] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 613.235966] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 613.235993] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 613.237505] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 621.069065] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 621.069086] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 621.070147] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 631.129005] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 631.129026] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 631.130085] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 641.188240] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 641.188262] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 641.189232] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 946.067745] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 946.067765] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 946.068748] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 956.121997] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 956.122027] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 956.123579] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 966.176142] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 966.176162] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 966.177317] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 974.066320] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 974.066341] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 974.067686] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 984.128315] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 984.128337] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 984.129320] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 994.189977] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 994.189997] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 994.190962] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1002.067713] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 1002.067734] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 1002.068706] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1012.125700] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 1012.125721] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 1012.126788] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1022.190971] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 1022.190992] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 1022.191972] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1030.088155] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 1030.088183] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 1030.089675] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1040.156426] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 1040.156457] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 1040.157985] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1050.214562] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 1050.214583] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 1050.215558] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1107.132053] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 1107.132076] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 1107.133055] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1117.187242] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 1117.187263] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 1117.188272] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1127.242173] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 1127.242199] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 1127.243409] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1175.521957] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 1175.521978] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 1175.522963] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1185.585545] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 1185.585565] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 1185.586542] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1195.641769] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 1195.641789] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 1195.642767] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1209.168933] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 1209.168954] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 1209.170000] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1219.225774] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 1219.225795] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 1219.226901] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1229.282696] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 1229.282717] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 1229.283893] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1237.504609] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 1237.504629] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 1237.505635] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1247.559347] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 1247.559368] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 1247.560518] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1257.646674] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 1257.646703] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 1257.648176] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1563.067816] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 1563.067837] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 1563.068793] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1573.129834] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 1573.129912] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 1573.131361] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1583.188580] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 1583.188601] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 1583.189572] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1591.070349] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 1591.070370] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 1591.071350] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1601.128453] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 1601.128474] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 1601.129606] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1611.185662] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 1611.185683] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 1611.186774] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1619.070815] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 1619.070836] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 1619.071829] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1629.127075] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[ 1629.127097] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[ 1629.128273] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[16694.722281] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[16694.722302] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[16694.723273] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[16696.431180] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[16696.431201] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[16696.432344] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[16706.485996] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[16706.486017] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[16706.486988] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[16716.542110] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: false (implement)
[16716.542131] ieee80211 phy0: brcms_ops_config: change power-save mode: false (implement)
[16716.543117] ADDRCONF(NETDEV_UP): wlan0: link is not readyEnglish isn't my native langage
Offline
#8 2012-05-05 09:50:28
- Gusar
- Member
- Registered: 2009-08-25
- Posts: 3,605
Re: [wifi] bcm4313 troubles with linux-lqx 3.3.4-2
Ok, it seems those are actual error messages, the cards gets stuck in a specific state and can't get out of it. Bad kernel I think. Either downgrade it, or upgrade to the very latest (3.4-rc5).
Offline
#9 2012-05-06 00:00:11
- spiky25
- Member
- Registered: 2009-09-29
- Posts: 134
Re: [wifi] bcm4313 troubles with linux-lqx 3.3.4-2
1-
02:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01)
Subsystem: Broadcom Corporation Device [14e4:0510]
2-
MODULES=()
3-
bcma 21810 1 brcmsmac
mbcache 5977 1 ext4
usbcore 146815 4 ehci_hcd,uhci_hcd,uvcvideo
usb_common 954 1 usbcore
4-
none
5-
nothing else than modprobe.conf :
alias floppy off
blacklist fd0
blacklist floppy
blacklist ipv6
blacklist pcspkr
blacklist snd_pcsp
English isn't my native langage
Offline
#10 2012-05-06 11:30:58
- sano
- Member
- Registered: 2012-02-11
- Posts: 114
Re: [wifi] bcm4313 troubles with linux-lqx 3.3.4-2
I have the same card and it's working fine with the built-in kernel driver. I get the same lines as you in dmesg when the driver is loaded, and dmesg and tty's are flooded with harmless
ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDUmessages afterwards, but that is only annoying when working on a tty. There are some workarounds for this in the forums, haven't tried them so far though.
My advice: Remove broadcom-wl, reboot, check dmesg for complaints about missing firmware if your card doesn't show up in iwconfig and report back here.
Btw, my relevant snippets from lsmod:
cordic 1073 1 brcmsmac
crc8 1186 1 brcmsmac
brcmutil 3216 1 brcmsmac
mac80211 394623 1 brcmsmac
cfg80211 177753 2 mac80211,brcmsmac
bcma 22098 1 brcmsmac
...
rfkill 15732 2 cfg80211,acer_wmiOffline