Arch Linux

celebrimbor

Member

From: Philadelphia, PA

Registered: 2012-07-04

Posts: 56

Hovering mouse over tint2 taskbar causes X server to crash

I tried running tint2 and tint2-svn on openbox, compiz-standalone, and xfce4 (with xfwm). It works fine as long as compositing is not enabled.
But when I enable compoziting (xcompmgr in case of openbox), hovering the mouse over tint2 taskbar causes X server to crash. X works fine and I can succesfully launch apps from tint2 launcher.
I have fully updated arch system installed.
If it matters, I am running arch on Dell Inspiron N4010 laptop with i915 graphics and I have configured them as per arch wiki. No other app causes such behaviour.

My lspci:

00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18)
00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18)
00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06)
00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06)
00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06)
00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06)
00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06)
00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06)
00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6)
00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06)
00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 06)
00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06)
00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06)
03:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 [Condor Peak]
04:00.0 Ethernet controller: Atheros Communications Inc. AR8152 v1.1 Fast Ethernet (rev c1)
ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 05)
ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 05)
ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 05)
ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 05)
ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 05)
ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 05)

Xorg.0.log

tint2rc

---

“If you wish to make an apple pie from scratch, you must first invent the universe.”
― Carl Sagan, Cosmos

WonderWoofy

Member

From: Los Gatos, CA

Registered: 2012-05-19

Posts: 8,414

Re: Hovering mouse over tint2 taskbar causes X server to crash

No output, no logs, no useful info...

celebrimbor

Member

From: Philadelphia, PA

Registered: 2012-07-04

Posts: 56

Re: Hovering mouse over tint2 taskbar causes X server to crash

What info, apart from the one I provided, should I post? I don't even receive any message at all when X crashes and nothing responds and I have to manually shutdown.

---

“If you wish to make an apple pie from scratch, you must first invent the universe.”
― Carl Sagan, Cosmos

Kolibry

Member

Registered: 2012-12-20

Posts: 110

Re: Hovering mouse over tint2 taskbar causes X server to crash

Did you resolve your problem ? I'm having the same one :s

---

Asus 1225B - 11,6" -  AMD E-60 Dual Core 1,3Ghz - 4 Go RAM - Disque dur SSD 128 Go -  Radeon HD6290
ArchLinux Openbox - My Github