You are not logged in.

#1 2012-11-30 16:57:19

Archdove
Member
Registered: 2011-09-23
Posts: 118

awesome wm (only) langague & regional settings

Hi

So. With Gnome 3.6 i switched to awesome wm. Actually i'm in the process of switching since a few weeks.
Since i removed most of the gnome packages i'm facing some strange issues about stuff just not working anymore. Some things i could fix on my own. For some things i just couldn't find the time and other things just seem to be unfixable.

1) Language Settings
I used to have the language settings set to en_US and the regional settings (time, currency and stuff) to de_CH. This wasn't the case anymore. I noticed that something is wrong when i found me unable to compile a latex file with some umlauts in it. Also typing umlauts öäü in Terminal (xfce terminal) would result in ???.
=> I adjusted the locale in /etc/locale.conf by setting LANG="de_CH.UTF-8"
Good thing is, i can type umlauts in terminal again. Bad thing is, my system output is german now. Also compiling latex with utf8 is still not working.

Question: How can i set different locales for language und regional stuff? And activate UTF-8 system wide. (utf is the way to go right?)

2) eth0 not working when plugged in after boot
When i boot my system with ethernet plugged in, it just works. Booting without and plugging in afterwards won't set up link. In fact no led is on. Network Manager is working and i tried to activate the port with "ip link set eth0 up".

Some hints would be nice. I realise how dependent on the gui stuff i actually am.

Regards, Dove

Offline

#2 2012-11-30 17:04:42

kaszak696
Member
Registered: 2009-05-26
Posts: 543

Re: awesome wm (only) langague & regional settings

You can adjust many locale variables, not just LANG. Look here.


'What can be asserted without evidence can also be dismissed without evidence.' - Christopher Hitchens
'There's no such thing as addiction, there's only things that you enjoy doing more than life.' - Doug Stanhope
GitHub Junkyard

Offline

#3 2012-11-30 17:09:18

Archdove
Member
Registered: 2011-09-23
Posts: 118

Re: awesome wm (only) langague & regional settings

Thanks. Yes i know that. In fact i tried most of the settings i received while executing "locale" in terminal. But i couln't evaluate the right settings.
Everything else but de_CH wouldn't allow me to type the umlauts. Not to mention the general problem with UTF in latex.

Last edited by Archdove (2012-11-30 17:15:18)

Offline

#4 2012-11-30 17:17:54

Antoine
Member
From: Picton Ontario
Registered: 2012-10-11
Posts: 90

Re: awesome wm (only) langague & regional settings

Archdove wrote:

2) eth0 not working when plugged in after boot
When i boot my system with ethernet plugged in, it just works. Booting without and plugging in afterwards won't set up link. In fact no led is on. Network Manager is working and i tried to activate the port with "ip link set eth0 up".

You can  use the nm-applet (from Gnome) with awesome. It will sit up in your "taskbar" next to the date. I start it in ~/.xinitrc:

/usr/bin/nm-applet --sm-disable &

then you can click and right-click on it and so on, manage your network connections.

You might want also to look at the man page for nmcli, which comes with Network Manager. I use it to bring up my VPN connection, either remotely or via ~/.xinitrc.

Sorry, I can't help with the locale stuff.

Offline

#5 2012-11-30 21:02:36

Archdove
Member
Registered: 2011-09-23
Posts: 118

Re: awesome wm (only) langague & regional settings

Actually NetworkManager is working fine. The Ethernet port just doesn't seem to recognize a connection when there is no cable plugged in on startup. I intended to write that but my english is bad sometimes.

Offline

Board footer

Powered by FluxBB