You are not logged in.
I am not sure what I installed to do this but I noticed the lines in my console are being replaced with strange characters (see first two photos)
The same programs are fine in xfce:
Sorry, I don't have any more information than what I displayed here. Thanks for any help.
Last edited by tedbell (2013-04-12 16:39:34)
Offline
Apparently it’s some encoding (iso-8859-? vs. cp85?) problem. What is in your /etc/vconsole.conf and /etc/locale.conf files?
Last edited by barto (2013-04-11 18:02:47)
“First principle, Clarice. Simplicity” – Dr. Hannibal Lecter
Offline
Thanks. Here's my vconsole.conf:
KEYMAP=us
FONT=lat9w-16
FONT_MAP=8859-1_to_uniAnd locale.conf:
LANG=en_US.UTF-8Offline
FONT=lat9w-16
You may want to try two things:
1) Try setting the font manually, using setfont:
setfont lat9w-16.psfu.gzIf everything looks fine, you should probably edit your /etc/mkinitcpio.conf and add two bits there:
a) add your video module at the beginning of the MODULES array (in my case it's MODULES="i915 ...")
b) add consolefont hook at the beginning of the HOOKS
-- and re-run mkinitcpio. This is done to prevent re-setting your vconsole settings when the video module is loaded at boot.
2) If 1) doesn't seem to change anything, try using a different console font. Simply go to /usr/share/kbd/consolefonts/ and experiment with
setfont <font.file.gz>The one that does the job you should put in your /etc/vconsole.conf (without any extensions and suffixes). You may still follow the steps in 1) to make changes more permanent.
:: Registered Linux User No. 223384
:: github
:: infinality-bundle+fonts: good looking fonts made easy
Offline
Thanks for the help! I'll try these out but I am using a G41 Chipset. Do you know if this is supported?
Offline
I don't think a different chipset really matters once you've got a working driver. Even with pure SVGA you can use any font you wish in the console. Step 1) is valid if you want to prevent overriding custom settings when the video module is loaded (which may be the case here). If you want to try getting it fixed, just check if the font you're currently using, when loaded manually, works correctly. If it does, than mkinitcpio related stuff will come in handy. If not -- pick a different one. If the text in the console looks OK after rebooting the system, you don't have to do anything. If not -- go to point 1). ![]()
:: Registered Linux User No. 223384
:: github
:: infinality-bundle+fonts: good looking fonts made easy
Offline
No luck so far. I am still getting strange characters replacing the lines.
Here is my current vconsole.conf:
KEYMAP=us
FONT=LatGrkCyr-8x16
FONT_MAP=8859-1_to_uniI am not sure where to find more font maps if that font map is the problem.
Here is my mkinitcpio.conf:
# vim:set ft=sh
# MODULES
# The following modules are loaded before any boot hooks are
# run. Advanced users may wish to specify all system modules
# in this array. For instance:
# MODULES="piix ide_disk reiserfs"
MODULES=""
# BINARIES
# This setting includes any additional binaries a given user may
# wish into the CPIO image. This is run last, so it may be used to
# override the actual binaries included by a given hook
# BINARIES are dependency parsed, so you may safely ignore libraries
BINARIES=""
# FILES
# This setting is similar to BINARIES above, however, files are added
# as-is and are not parsed in any way. This is useful for config files.
FILES="/etc/modprobe.d/modprobe.conf"
# HOOKS
# This is the most important setting in this file. The HOOKS control the
# modules and scripts added to the image, and what happens at boot time.
# Order is important, and it is recommended that you do not change the
# order in which HOOKS are added. Run 'mkinitcpio -H <hook name>' for
# help on a given hook.
# 'base' is _required_ unless you know precisely what you are doing.
# 'udev' is _required_ in order to automatically load modules
# 'filesystems' is _required_ unless you specify your fs modules in MODULES
# Examples:
## This setup specifies all modules in the MODULES setting above.
## No raid, lvm2, or encrypted root is needed.
# HOOKS="base"
#
## This setup will autodetect all modules for your system and should
## work as a sane default
# HOOKS="base udev autodetect block filesystems"
#
## This setup will generate a 'full' image which supports most systems.
## No autodetection is done.
# HOOKS="base udev block filesystems"
#
## This setup assembles a pata mdadm array with an encrypted root FS.
## Note: See 'mkinitcpio -H mdadm' for more information on raid devices.
# HOOKS="base udev block mdadm encrypt filesystems"
#
## This setup loads an lvm2 volume group on a usb device.
# HOOKS="base udev block lvm2 filesystems"
#
## NOTE: If you have /usr on a separate partition, you MUST include the
# usr, fsck and shutdown hooks.
HOOKS="base udev autodetect modconf block filesystems usbinput fsck consolefont keymap"
# COMPRESSION
# Use this to compress the initramfs image. By default, gzip compression
# is used. Use 'cat' to create an uncompressed image.
#COMPRESSION="gzip"
#COMPRESSION="bzip2"
#COMPRESSION="lzma"
#COMPRESSION="xz"
#COMPRESSION="lzop"
# COMPRESSION_OPTIONS
# Additional options for the compressor
#COMPRESSION_OPTIONS=""I tried adding "G41" to the modules array but it returned "No module found".
Thanks again for the help...
Offline
I'm afraid your driver will be something like i915, too... Issue 'lsmod | grep video' and check the output.
Besides, get the output of 'locale -a' and 'locale' respectively. If there is no UTF-8 active, you will have to modify your settings, too (either globally, or simply by appending a line to your .bashrc / .bash_profile). Of course, if your shell is BASH.
:: Registered Linux User No. 223384
:: github
:: infinality-bundle+fonts: good looking fonts made easy
Offline
I think either adding the module or commenting out the locale fixed it. bohoomil you're a genius. Thank you ![]()
Offline