Arch Linux

zilverling

Member

From: Bennekom, Netherlands

Registered: 2009-08-19

Posts: 84

USB 2.0 not functioning properly after upgrading to 3.10.3-1 kernel

After upgrading to the 3.10.3-1 kernel USB 2.0 is not working anymore on my ASrock ION330 nettop.
I just did a system upgrade (including a kernel upgrade to 3.10.5-1), but the problem remains...

Here's the relevant messages that I extracted with journalctl -b

Aug 07 09:59:11 alcyone kernel: ACPI: bus type USB registered
Aug 07 09:59:11 alcyone kernel: usbcore: registered new interface driver usbfs
Aug 07 09:59:11 alcyone kernel: usbcore: registered new interface driver hub
Aug 07 09:59:11 alcyone kernel: usbcore: registered new device driver usb
Aug 07 09:59:11 alcyone kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Aug 07 09:59:11 alcyone kernel: ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Aug 07 09:59:11 alcyone kernel: ehci-pci: EHCI PCI platform driver
Aug 07 09:59:11 alcyone kernel: ohci_hcd 0000:00:04.0: setting latency timer to 64
Aug 07 09:59:11 alcyone kernel: ohci_hcd 0000:00:04.0: OHCI Host Controller
Aug 07 09:59:11 alcyone kernel: ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 1
Aug 07 09:59:11 alcyone kernel: ohci_hcd 0000:00:04.0: irq 16, io mem 0xfae7f000
Aug 07 09:59:11 alcyone kernel: hub 1-0:1.0: USB hub found
Aug 07 09:59:11 alcyone kernel: hub 1-0:1.0: 6 ports detected
Aug 07 09:59:11 alcyone kernel: ehci-pci 0000:00:04.1: setting latency timer to 64
Aug 07 09:59:11 alcyone kernel: ehci-pci 0000:00:04.1: EHCI Host Controller
Aug 07 09:59:11 alcyone kernel: ehci-pci 0000:00:04.1: new USB bus registered, assigned bus number 2
Aug 07 09:59:11 alcyone kernel: ehci-pci 0000:00:04.1: debug port 1
Aug 07 09:59:11 alcyone kernel: ehci-pci 0000:00:04.1: cache line size of 64 is not supported
Aug 07 09:59:11 alcyone kernel: ehci-pci 0000:00:04.1: irq 18, io mem 0xfae7ec00
Aug 07 09:59:11 alcyone kernel: ehci-pci 0000:00:04.1: USB 2.0 started, EHCI 1.00
Aug 07 09:59:11 alcyone kernel: hub 2-0:1.0: USB hub found
Aug 07 09:59:11 alcyone kernel: hub 2-0:1.0: 6 ports detected
Aug 07 09:59:11 alcyone kernel: hub 1-0:1.0: USB hub found
Aug 07 09:59:11 alcyone kernel: hub 1-0:1.0: 6 ports detected
Aug 07 09:59:11 alcyone kernel: usb 2-2: new high-speed USB device number 3 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-2: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-2: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-2: new high-speed USB device number 4 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-2: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-2: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-2: new high-speed USB device number 5 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-2: device not accepting address 5, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-2: new high-speed USB device number 6 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-2: device not accepting address 6, error -71
Aug 07 09:59:11 alcyone kernel: hub 2-0:1.0: unable to enumerate USB device on port 2
Aug 07 09:59:11 alcyone kernel: usb 2-3: new high-speed USB device number 7 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-3: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-3: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-3: new high-speed USB device number 8 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-3: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-3: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-3: new high-speed USB device number 9 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-3: device not accepting address 9, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-3: new high-speed USB device number 10 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-3: device not accepting address 10, error -71
Aug 07 09:59:11 alcyone kernel: hub 2-0:1.0: unable to enumerate USB device on port 3
Aug 07 09:59:11 alcyone kernel: usb 2-5: new high-speed USB device number 12 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-5: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-5: device descriptor read/64, error -71
Aug 07 09:59:12 alcyone kernel: usb 2-5: new high-speed USB device number 13 using ehci-pci
Aug 07 09:59:12 alcyone kernel: usb 2-5: device descriptor read/64, error -71
Aug 07 09:59:12 alcyone kernel: usb 2-5: device descriptor read/64, error -71
Aug 07 09:59:12 alcyone kernel: usb 2-5: new high-speed USB device number 14 using ehci-pci
Aug 07 09:59:13 alcyone kernel: usb 2-5: device not accepting address 14, error -71
Aug 07 09:59:13 alcyone kernel: usb 2-5: device not accepting address 15, error -71
Aug 07 09:59:13 alcyone kernel: hub 2-0:1.0: unable to enumerate USB device on port 5
Aug 07 09:59:13 alcyone systemd[1]: Found device MCP79 Ethernet.
Aug 07 09:59:14 alcyone kernel: usb 1-1: new low-speed USB device number 2 using ohci_hcd
Aug 07 09:59:14 alcyone kernel: usb 1-4: new low-speed USB device number 3 using ohci_hcd

I'm glad that keyboard and mouse are working properly under USB 1.0, but neither my usb-parport printer nor my USB external hard drive are recognised any more :-(

Any ideas how to solve this?? (I'd prefer not to downgrade the kernel)

Last edited by zilverling (2013-08-07 14:28:36)

rasertux

Member

From: Florianópolis, Brazil

Registered: 2012-03-03

Posts: 51

Re: USB 2.0 not functioning properly after upgrading to 3.10.3-1 kernel

The same error here. Downgrade the kernel to 3.10.2 make the things work again.
https://bugs.archlinux.org/task/36296

zilverling

Member

From: Bennekom, Netherlands

Registered: 2009-08-19

Posts: 84

Re: USB 2.0 not functioning properly after upgrading to 3.10.3-1 kernel

I've discovered it's not that USB 2.0 is not working. 3 out of 6 usb ports/busses seem to work properly. The other three seem totally dead. Obviously this was not the case under kernel 3.9.9-1. Downgrading to kernel 3.10.2 made no difference.

In practical terms this means that I can use my printer and access my external drive if I use the right port/bus. And I could probably work around the problem by plugging a USB hub in one of the working ports. But I would be happy to get rid of the error messages and have all 6 usb busses working as they did before...