You are not logged in.

#1 2013-12-11 12:53:35

virusso80
Member
From: Italy
Registered: 2007-03-09
Posts: 325

Virtualbox network configuration host (arch) - guest (centos6.5)

Hi all,
I know there are tons of posts on this issue, but it's 2 days I'm not able to find a solution.
I have a host with arch x64 and a guest with centos6.5 x64

I need to be able to use ssh from host to guest (at least). I read that I needed a host-only adapter. I had a NAT already configured (which allowed me to connect the internet), then I added a new adapter hostonly vboxnet0 (it has been added after the centos installation...i don't know if it matters)

starting the guest machine, ifconfig command shows that eth1 (the hostonly adapt) is active with ipaddress: 192.168.56.101 BUT it is not pingable from the host. i enabled the eth0 (nat), guest is able to reach web, but again I'm not able to ping from host.
I disabled on the guest all services that could block anything: iptables, selinux.

I then tried setting the eth0 to bridged mode, but nothing changed.
this is the output of the guest ifconfig command:

[root@centos65vm ~]# ifconfig
eth0      Link encap:Ethernet  HWaddr 08:00:27:F5:CC:23  
          inet addr:192.168.16.200  Bcast:192.168.16.255  Mask:255.255.255.0
          inet6 addr: fe80::a00:27ff:fef5:cc23/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:468 errors:0 dropped:0 overruns:0 frame:0
          TX packets:35 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:71501 (69.8 KiB)  TX bytes:3602 (3.5 KiB)

eth1      Link encap:Ethernet  HWaddr 08:00:27:C6:E9:F3  
          inet addr:192.168.56.101  Bcast:192.168.56.255  Mask:255.255.255.0
          inet6 addr: fe80::a00:27ff:fec6:e9f3/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:15 errors:0 dropped:0 overruns:0 frame:0
          TX packets:21 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:6200 (6.0 KiB)  TX bytes:4098 (4.0 KiB)

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:44 errors:0 dropped:0 overruns:0 frame:0
          TX packets:44 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:3192 (3.1 KiB)  TX bytes:3192 (3.1 KiB)

virbr0    Link encap:Ethernet  HWaddr 52:54:00:5A:2E:06  
          inet addr:192.168.122.1  Bcast:192.168.122.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

The strange thing is that from virtual box main manager, if I edit properties of the hostonly adapter I can disable dhcp option, and set the ip address to 192.168.56.1 or 192.168.56.10 or whatever when restarting the host is always getting ip 101. very strange, no?

forcing the correct address with

ifconfig eth1 192.168.56.1 netmask 255.255.255.0 up

ip is correct but still not able to ping or ssh...

I don't really know what to do!

Thanks in advance

Offline

Board footer

Powered by FluxBB