Arch Linux

Isildur

Member

Registered: 2009-05-26

Posts: 100

[solved]Printing error - cups/kyocera

I normally print using CUPS and a Kyocera FS1030D connected via network. This used to work fine until recently (apparently after recent updates), now I get an error when trying to print.
The error is printed by the printer:

ERROR:
typecheck
OFFENDING COMMAND:
idiv
50000
--nostringval--
--nostringval--
-mark-
-mark-
-mark-
-mark-

CUPS itself apparently doesn't receive any errors:

% cat /var/log/cups/error_log
D [25/Feb/2015:22:56:45 +0100] [Job 557] Wrote 1 pages...
D [25/Feb/2015:22:56:45 +0100] [Job 557] PID 4451 (pstops) exited with no errors.
D [25/Feb/2015:22:56:45 +0100] [Job 557] PID 4447 (/usr/lib/cups/filter/pdftops) exited with no errors.
D [25/Feb/2015:22:56:45 +0100] [Job 557] Wrote 8192 bytes of print data...
D [25/Feb/2015:22:56:45 +0100] [Job 557] Read 8192 bytes of print data...
D [25/Feb/2015:22:56:45 +0100] [Job 557] Wrote 8192 bytes of print data...
D [25/Feb/2015:22:56:45 +0100] [Job 557] Read 8192 bytes of print data...
D [25/Feb/2015:22:56:45 +0100] [Job 557] Wrote 8192 bytes of print data...
D [25/Feb/2015:22:56:45 +0100] [Job 557] Read 8192 bytes of print data...
D [25/Feb/2015:22:56:45 +0100] [Job 557] Wrote 8192 bytes of print data...
D [25/Feb/2015:22:56:45 +0100] [Job 557] Read 8192 bytes of print data...
D [25/Feb/2015:22:56:45 +0100] [Job 557] Wrote 8192 bytes of print data...
D [25/Feb/2015:22:56:45 +0100] [Job 557] Read 8192 bytes of print data...
D [25/Feb/2015:22:56:45 +0100] [Job 557] Wrote 8192 bytes of print data...
D [25/Feb/2015:22:56:45 +0100] [Job 557] Read 8192 bytes of print data...
D [25/Feb/2015:22:56:45 +0100] [Job 557] Wrote 8192 bytes of print data...
D [25/Feb/2015:22:56:45 +0100] [Job 557] Read 2727 bytes of print data...
D [25/Feb/2015:22:56:45 +0100] [Job 557] Wrote 2727 bytes of print data...
D [25/Feb/2015:22:56:45 +0100] [Job 557] STATE: +cups-waiting-for-job-completed
D [25/Feb/2015:22:56:45 +0100] [Job 557] Waiting for printer to finish.
D [25/Feb/2015:22:56:45 +0100] [Job 557] PID 4448 (/usr/lib/cups/backend/socket) exited with no errors.
D [25/Feb/2015:22:56:45 +0100] [Job 557] End of messages
D [25/Feb/2015:22:56:45 +0100] [Job 557] printer-state=3(idle)
D [25/Feb/2015:22:56:45 +0100] [Job 557] printer-state-message="Waiting for printer to finish."
D [25/Feb/2015:22:56:45 +0100] [Job 557] printer-state-reasons=none

I tried modifying the printer and resetting the PPD to no avail. I'm open and for any suggestions.

Thank you in advance!

edit: I fixed the problem. The root partition just ran out of space leaving not enough disk space to save the tmp file before sending it completely to the printer.

Last edited by Isildur (2015-02-26 15:28:48)