You are not logged in.
- Topics: Active | Unanswered
Pages: 1
#1 2015-05-10 09:35:13
- Ivan1pl
- Member
- Registered: 2012-03-12
- Posts: 3
ATA bus error
Hello,
I have some problems with hard drive on my laptop. Sometimes everything freezes for few seconds (usually during start-up, but sometimes after I login) and I get some errors. After that, everything seems to be working fine.
Part of dmesg with errors:
[ 10.019887] ata1.00: cmd 60/00:10:10:da:59/01:00:0f:00:00/40 tag 2 ncq 131072 in
res 41/84:00:f2:da:59/00:01:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 10.019968] ata1.00: status: { DRDY ERR }
[ 10.019992] ata1.00: error: { ICRC ABRT }
[ 10.020017] ata1: hard resetting link
[ 10.339913] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 10.443163] ata1.00: configured for UDMA/133
[ 10.443191] ata1: EH complete
[ 10.516832] ata1.00: exception Emask 0x0 SAct 0x7000 SErr 0x0 action 0x6
[ 10.516877] ata1.00: irq_stat 0x40000008
[ 10.516902] ata1.00: failed command: READ FPDMA QUEUED
[ 10.516935] ata1.00: cmd 60/e8:60:e8:16:3b/00:00:0f:00:00/40 tag 12 ncq 118784 in
res 41/84:e8:8c:17:3b/00:00:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 10.517017] ata1.00: status: { DRDY ERR }
[ 10.517041] ata1.00: error: { ICRC ABRT }
[ 10.517067] ata1: hard resetting link
[ 10.836973] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 10.964972] ata1.00: configured for UDMA/133
[ 10.965002] ata1: EH complete
[ 10.984003] ata1: limiting SATA link speed to 3.0 Gbps
[ 10.984015] ata1.00: exception Emask 0x0 SAct 0x60020000 SErr 0x0 action 0x6
[ 10.984106] ata1.00: irq_stat 0x40000008
[ 10.984157] ata1.00: failed command: READ FPDMA QUEUED
[ 10.984225] ata1.00: cmd 60/20:e8:40:6e:b0/00:00:13:00:00/40 tag 29 ncq 16384 in
res 41/84:20:46:6e:b0/00:00:13:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 10.984397] ata1.00: status: { DRDY ERR }
[ 10.984445] ata1.00: error: { ICRC ABRT }
[ 10.984497] ata1: hard resetting link
[ 11.304016] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 11.409308] ata1.00: configured for UDMA/133
[ 11.409343] ata1: EH complete
[ 11.441025] vboxpci: IOMMU not found (not registered)
[ 11.543239] bbswitch: version 0.8
[ 11.543246] bbswitch: Found integrated VGA device 0000:00:02.0: \_SB_.PCI0.GFX0
[ 11.543252] bbswitch: Found discrete VGA device 0000:03:00.0: \_SB_.PCI0.RP05.PEGP
[ 11.543262] ACPI Warning: \_SB_.PCI0.RP05.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[ 11.543355] bbswitch: detected an Optimus _DSM function
[ 11.543372] pci 0000:03:00.0: enabling device (0006 -> 0007)
[ 11.543434] bbswitch: Succesfully loaded. Discrete card 0000:03:00.0 is on
[ 11.545169] bbswitch: disabling discrete graphics
[ 11.545181] ACPI Warning: \_SB_.PCI0.RP05.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[ 13.327790] r8169 0000:01:00.0 enp1s0: link up
[ 20.651344] ata1.00: exception Emask 0x0 SAct 0x2000000 SErr 0x0 action 0x6
[ 20.651349] ata1.00: irq_stat 0x40000008
[ 20.651353] ata1.00: failed command: READ FPDMA QUEUED
[ 20.651359] ata1.00: cmd 60/08:c8:98:86:ae/00:00:10:00:00/40 tag 25 ncq 4096 in
res 41/84:08:98:86:ae/00:00:10:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 20.651361] ata1.00: status: { DRDY ERR }
[ 20.651363] ata1.00: error: { ICRC ABRT }
[ 20.651367] ata1: hard resetting link
[ 20.971293] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 21.080441] ata1.00: configured for UDMA/133
[ 21.080467] ata1: EH complete
[ 21.121498] ata1.00: exception Emask 0x0 SAct 0x20000000 SErr 0x0 action 0x6
[ 21.121503] ata1.00: irq_stat 0x40000008
[ 21.121507] ata1.00: failed command: READ FPDMA QUEUED
[ 21.121513] ata1.00: cmd 60/00:e8:00:f4:69/01:00:0f:00:00/40 tag 29 ncq 131072 in
res 41/84:00:ee:f4:69/00:01:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 21.121515] ata1.00: status: { DRDY ERR }
[ 21.121517] ata1.00: error: { ICRC ABRT }
[ 21.121521] ata1: hard resetting link
[ 21.441483] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 21.546775] ata1.00: configured for UDMA/133
[ 21.546795] sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x08
[ 21.546798] sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
[ 21.546801] sd 0:0:0:0: [sda] ASC=0x47 ASCQ=0x0
[ 21.546802] sd 0:0:0:0: [sda] CDB:
[ 21.546804] cdb[0]=0x28: 28 00 0f 69 f4 00 00 01 00 00
[ 21.546812] blk_update_request: I/O error, dev sda, sector 258601984
[ 21.546829] ata1: EH complete
[ 21.606131] ata1.00: exception Emask 0x0 SAct 0x200 SErr 0x0 action 0x6
[ 21.606139] ata1.00: irq_stat 0x40000008
[ 21.606145] ata1.00: failed command: READ FPDMA QUEUED
[ 21.606155] ata1.00: cmd 60/88:48:00:d8:36/00:00:0f:00:00/40 tag 9 ncq 69632 in
res 41/84:88:04:d8:36/00:00:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 21.606160] ata1.00: status: { DRDY ERR }
[ 21.606163] ata1.00: error: { ICRC ABRT }
[ 21.606170] ata1: hard resetting link
[ 21.924963] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 22.035385] ata1.00: configured for UDMA/133
[ 22.035408] ata1: EH complete
[ 22.111984] ata1: limiting SATA link speed to 1.5 Gbps
[ 22.111991] ata1.00: exception Emask 0x0 SAct 0x1000000 SErr 0x0 action 0x6
[ 22.111994] ata1.00: irq_stat 0x40000008
[ 22.111997] ata1.00: failed command: READ FPDMA QUEUED
[ 22.112003] ata1.00: cmd 60/90:c0:48:39:32/00:00:0f:00:00/40 tag 24 ncq 73728 in
res 41/84:90:8a:39:32/00:00:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 22.112005] ata1.00: status: { DRDY ERR }
[ 22.112007] ata1.00: error: { ICRC ABRT }
[ 22.112011] ata1: hard resetting link
[ 22.431783] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 22.535011] ata1.00: configured for UDMA/133
[ 22.535038] ata1: EH complete
[ 22.618877] ata1.00: exception Emask 0x0 SAct 0x1e SErr 0x0 action 0x6
[ 22.618886] ata1.00: irq_stat 0x40000008
[ 22.618891] ata1.00: failed command: READ FPDMA QUEUED
[ 22.618901] ata1.00: cmd 60/00:08:08:2c:32/01:00:0f:00:00/40 tag 1 ncq 131072 in
res 41/84:00:70:2c:32/00:01:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 22.618906] ata1.00: status: { DRDY ERR }
[ 22.618909] ata1.00: error: { ICRC ABRT }
[ 22.618920] ata1: hard resetting link
[ 22.938608] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 23.023643] ata1.00: configured for UDMA/133
[ 23.023682] ata1: EH complete
[ 53.428943] ata1.00: exception Emask 0x1 SAct 0x7fffffff SErr 0x0 action 0x6 frozen
[ 53.428953] ata1.00: irq_stat 0x40000008
[ 53.428960] ata1.00: failed command: READ FPDMA QUEUED
[ 53.428971] ata1.00: cmd 60/00:00:00:e8:31/01:00:10:00:00/40 tag 0 ncq 131072 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x5 (timeout)
[ 53.428976] ata1.00: status: { DRDY }
[ 53.428981] ata1.00: failed command: READ FPDMA QUEUED
[ 53.428990] ata1.00: cmd 60/08:08:20:fe:e9/00:00:0f:00:00/40 tag 1 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.428994] ata1.00: status: { DRDY }
[ 53.428998] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429006] ata1.00: cmd 60/08:10:28:fe:e9/00:00:0f:00:00/40 tag 2 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429010] ata1.00: status: { DRDY }
[ 53.429014] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429022] ata1.00: cmd 60/08:18:30:fe:e9/00:00:0f:00:00/40 tag 3 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429026] ata1.00: status: { DRDY }
[ 53.429029] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429037] ata1.00: cmd 60/08:20:38:fe:e9/00:00:0f:00:00/40 tag 4 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429042] ata1.00: status: { DRDY }
[ 53.429045] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429053] ata1.00: cmd 60/08:28:40:fe:e9/00:00:0f:00:00/40 tag 5 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429057] ata1.00: status: { DRDY }
[ 53.429061] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429069] ata1.00: cmd 60/08:30:48:fe:e9/00:00:0f:00:00/40 tag 6 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429073] ata1.00: status: { DRDY }
[ 53.429076] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429084] ata1.00: cmd 60/08:38:50:fe:e9/00:00:0f:00:00/40 tag 7 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429089] ata1.00: status: { DRDY }
[ 53.429092] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429100] ata1.00: cmd 60/08:40:58:fe:e9/00:00:0f:00:00/40 tag 8 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429104] ata1.00: status: { DRDY }
[ 53.429108] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429116] ata1.00: cmd 60/08:48:60:fe:e9/00:00:0f:00:00/40 tag 9 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429120] ata1.00: status: { DRDY }
[ 53.429124] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429132] ata1.00: cmd 60/08:50:68:fe:e9/00:00:0f:00:00/40 tag 10 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429136] ata1.00: status: { DRDY }
[ 53.429139] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429148] ata1.00: cmd 60/08:58:70:fe:e9/00:00:0f:00:00/40 tag 11 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429152] ata1.00: status: { DRDY }
[ 53.429155] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429163] ata1.00: cmd 60/08:60:78:fe:e9/00:00:0f:00:00/40 tag 12 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429168] ata1.00: status: { DRDY }
[ 53.429171] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429179] ata1.00: cmd 60/08:68:80:fe:e9/00:00:0f:00:00/40 tag 13 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429183] ata1.00: status: { DRDY }
[ 53.429187] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429195] ata1.00: cmd 60/08:70:18:e8:a9/00:00:16:00:00/40 tag 14 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429199] ata1.00: status: { DRDY }
[ 53.429203] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429211] ata1.00: cmd 60/08:78:90:fe:e9/00:00:0f:00:00/40 tag 15 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429215] ata1.00: status: { DRDY }
[ 53.429218] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429226] ata1.00: cmd 60/08:80:98:fe:e9/00:00:0f:00:00/40 tag 16 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429230] ata1.00: status: { DRDY }
[ 53.429234] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429242] ata1.00: cmd 60/08:88:a0:fe:e9/00:00:0f:00:00/40 tag 17 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429246] ata1.00: status: { DRDY }
[ 53.429250] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429258] ata1.00: cmd 60/08:90:a8:fe:e9/00:00:0f:00:00/40 tag 18 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429262] ata1.00: status: { DRDY }
[ 53.429265] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429273] ata1.00: cmd 60/08:98:b0:fe:e9/00:00:0f:00:00/40 tag 19 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429277] ata1.00: status: { DRDY }
[ 53.429281] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429289] ata1.00: cmd 60/08:a0:b8:fe:e9/00:00:0f:00:00/40 tag 20 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429293] ata1.00: status: { DRDY }
[ 53.429297] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429305] ata1.00: cmd 60/08:a8:c0:fe:e9/00:00:0f:00:00/40 tag 21 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429309] ata1.00: status: { DRDY }
[ 53.429312] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429320] ata1.00: cmd 60/08:b0:c8:fe:e9/00:00:0f:00:00/40 tag 22 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429325] ata1.00: status: { DRDY }
[ 53.429328] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429336] ata1.00: cmd 60/08:b8:d0:fe:e9/00:00:0f:00:00/40 tag 23 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429340] ata1.00: status: { DRDY }
[ 53.429344] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429352] ata1.00: cmd 60/08:c0:d8:fe:e9/00:00:0f:00:00/40 tag 24 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429356] ata1.00: status: { DRDY }
[ 53.429360] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429367] ata1.00: cmd 60/08:c8:e0:fe:e9/00:00:0f:00:00/40 tag 25 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429372] ata1.00: status: { DRDY }
[ 53.429375] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429383] ata1.00: cmd 60/08:d0:e8:fe:e9/00:00:0f:00:00/40 tag 26 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429387] ata1.00: status: { DRDY }
[ 53.429391] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429399] ata1.00: cmd 60/08:d8:f0:fe:e9/00:00:0f:00:00/40 tag 27 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429403] ata1.00: status: { DRDY }
[ 53.429407] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429414] ata1.00: cmd 60/08:e0:f8:fe:e9/00:00:0f:00:00/40 tag 28 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429419] ata1.00: status: { DRDY }
[ 53.429422] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429430] ata1.00: cmd 60/08:e8:00:ff:e9/00:00:0f:00:00/40 tag 29 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429435] ata1.00: status: { DRDY }
[ 53.429438] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429446] ata1.00: cmd 60/08:f0:88:fe:e9/00:00:0f:00:00/40 tag 30 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429450] ata1.00: status: { DRDY }
[ 53.429458] ata1: hard resetting link
[ 53.749173] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 53.836070] ata1.00: configured for UDMA/133
[ 53.836079] ata1.00: device reported invalid CHS sector 0
[ 53.836116] sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x08
[ 53.836119] sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
[ 53.836121] sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
[ 53.836123] sd 0:0:0:0: [sda] CDB:
[ 53.836125] cdb[0]=0x28: 28 00 0f e9 fe 20 00 00 08 00
[ 53.836133] blk_update_request: I/O error, dev sda, sector 266993184
[ 53.836148] sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x08
[ 53.836151] sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
[ 53.836153] sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
[ 53.836154] sd 0:0:0:0: [sda] CDB:
[ 53.836155] cdb[0]=0x28: 28 00 0f e9 fe 28 00 00 08 00
[ 53.836162] blk_update_request: I/O error, dev sda, sector 266993192
[ 53.836167] sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x08
[ 53.836169] sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
[ 53.836171] sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
[ 53.836173] sd 0:0:0:0: [sda] CDB:
[ 53.836174] cdb[0]=0x28: 28 00 0f e9 fe 30 00 00 08 00
[ 53.836180] blk_update_request: I/O error, dev sda, sector 266993200
[ 53.836185] sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x08
[ 53.836187] sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
[ 53.836189] sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
[ 53.836190] sd 0:0:0:0: [sda] CDB:
[ 53.836191] cdb[0]=0x28: 28 00 0f e9 fe 38 00 00 08 00
[ 53.836198] blk_update_request: I/O error, dev sda, sector 266993208
[ 53.836202] sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x08
[ 53.836204] sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
[ 53.836206] sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
[ 53.836208] sd 0:0:0:0: [sda] CDB:
[ 53.836209] cdb[0]=0x28: 28 00 0f e9 fe 40 00 00 08 00
[ 53.836215] blk_update_request: I/O error, dev sda, sector 266993216
[ 53.836220] sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x08
[ 53.836222] sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
[ 53.836224] sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
[ 53.836225] sd 0:0:0:0: [sda] CDB:
[ 53.836226] cdb[0]=0x28: 28 00 0f e9 fe 48 00 00 08 00
[ 53.836232] blk_update_request: I/O error, dev sda, sector 266993224
[ 53.836237] sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x08
[ 53.836239] sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
[ 53.836241] sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
[ 53.836242] sd 0:0:0:0: [sda] CDB:
[ 53.836243] cdb[0]=0x28: 28 00 0f e9 fe 50 00 00 08 00
[ 53.836249] blk_update_request: I/O error, dev sda, sector 266993232
[ 53.836253] sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x08
[ 53.836255] sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
[ 53.836257] sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
[ 53.836259] sd 0:0:0:0: [sda] CDB:
[ 53.836260] cdb[0]=0x28: 28 00 0f e9 fe 58 00 00 08 00
[ 53.836266] blk_update_request: I/O error, dev sda, sector 266993240
[ 53.836270] sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x08
[ 53.836272] sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
[ 53.836274] sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
[ 53.836276] sd 0:0:0:0: [sda] CDB:
[ 53.836277] cdb[0]=0x28: 28 00 0f e9 fe 60 00 00 08 00
[ 53.836283] blk_update_request: I/O error, dev sda, sector 266993248
[ 53.836287] sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x08
[ 53.836289] sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
[ 53.836291] sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
[ 53.836293] sd 0:0:0:0: [sda] CDB:
[ 53.836294] cdb[0]=0x28: 28 00 0f e9 fe 68 00 00 08 00
[ 53.836300] blk_update_request: I/O error, dev sda, sector 266993256
[ 53.836354] ata1: EH complete
[ 53.922776] ata1.00: exception Emask 0x0 SAct 0x20 SErr 0x0 action 0x6
[ 53.922827] ata1.00: irq_stat 0x40000008
[ 53.922855] ata1.00: failed command: READ FPDMA QUEUED
[ 53.922891] ata1.00: cmd 60/00:28:38:3f:04/01:00:10:00:00/40 tag 5 ncq 131072 in
res 41/84:00:5a:3f:04/00:01:10:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 53.922981] ata1.00: status: { DRDY ERR }
[ 53.923007] ata1.00: error: { ICRC ABRT }
[ 53.923037] ata1: hard resetting link
[ 54.242882] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 54.357940] ata1.00: configured for UDMA/133
[ 54.357967] ata1: EH complete
[ 54.413337] ata1.00: limiting speed to UDMA/100:PIO4
[ 54.413343] ata1.00: exception Emask 0x0 SAct 0x100 SErr 0x0 action 0x6
[ 54.413387] ata1.00: irq_stat 0x40000008
[ 54.413412] ata1.00: failed command: READ FPDMA QUEUED
[ 54.413445] ata1.00: cmd 60/20:40:c0:04:b1/00:00:16:00:00/40 tag 8 ncq 16384 in
res 41/84:20:d4:04:b1/00:00:16:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 54.413527] ata1.00: status: { DRDY ERR }
[ 54.413551] ata1.00: error: { ICRC ABRT }
[ 54.413578] ata1: hard resetting link
[ 54.733264] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 54.835393] ata1.00: configured for UDMA/100
[ 54.835419] ata1: EH complete
[ 54.883575] ata1.00: exception Emask 0x0 SAct 0x8 SErr 0x0 action 0x6
[ 54.883618] ata1.00: irq_stat 0x40000008
[ 54.883643] ata1.00: failed command: READ FPDMA QUEUED
[ 54.883675] ata1.00: cmd 60/08:18:e0:04:b1/00:00:16:00:00/40 tag 3 ncq 4096 in
res 41/84:08:e4:04:b1/00:00:16:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 54.883756] ata1.00: status: { DRDY ERR }
[ 54.883779] ata1.00: error: { ICRC ABRT }
[ 54.883805] ata1: hard resetting link
[ 55.203636] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 55.301754] ata1.00: configured for UDMA/100
[ 55.301780] ata1: EH complete
[ 55.357428] ata1.00: exception Emask 0x0 SAct 0x40000 SErr 0x0 action 0x6
[ 55.357474] ata1.00: irq_stat 0x40000008
[ 55.357500] ata1.00: failed command: READ FPDMA QUEUED
[ 55.357532] ata1.00: cmd 60/f0:90:e0:34:a5/00:00:0e:00:00/40 tag 18 ncq 122880 in
res 41/84:f0:ea:34:a5/00:00:0e:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 55.357613] ata1.00: status: { DRDY ERR }
[ 55.357636] ata1.00: error: { ICRC ABRT }
[ 55.357661] ata1: hard resetting link
[ 55.677344] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 55.779200] ata1.00: configured for UDMA/100
[ 55.779228] ata1: EH complete
[ 55.954538] ata1.00: exception Emask 0x0 SAct 0xc0000 SErr 0x0 action 0x6
[ 55.954585] ata1.00: irq_stat 0x40000008
[ 55.954610] ata1.00: failed command: READ FPDMA QUEUED
[ 55.954643] ata1.00: cmd 60/00:90:00:eb:a4/01:00:0e:00:00/40 tag 18 ncq 131072 in
res 41/84:00:10:eb:a4/00:01:0e:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 55.954725] ata1.00: status: { DRDY ERR }
[ 55.954748] ata1.00: error: { ICRC ABRT }
[ 55.954774] ata1: hard resetting link
[ 56.274496] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 56.367864] ata1.00: configured for UDMA/100
[ 56.367921] ata1: EH complete
[ 56.448401] ata1.00: limiting speed to UDMA/33:PIO4
[ 56.448412] ata1.00: exception Emask 0x0 SAct 0x4 SErr 0x0 action 0x6
[ 56.448483] ata1.00: irq_stat 0x40000008
[ 56.448524] ata1.00: failed command: READ FPDMA QUEUED
[ 56.448578] ata1.00: cmd 60/00:10:58:ec:a4/01:00:0e:00:00/40 tag 2 ncq 131072 in
res 41/84:00:fe:ec:a4/00:01:0e:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 56.448715] ata1.00: status: { DRDY ERR }
[ 56.448753] ata1.00: error: { ICRC ABRT }
[ 56.448798] ata1: hard resetting link
[ 56.768215] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 56.856253] ata1.00: configured for UDMA/33
[ 56.856297] ata1: EH complete
[ 56.898690] ata1.00: exception Emask 0x0 SAct 0x60 SErr 0x0 action 0x6
[ 56.898770] ata1.00: irq_stat 0x40000008
[ 56.898816] ata1.00: failed command: READ FPDMA QUEUED
[ 56.898876] ata1.00: cmd 60/00:30:c8:ee:a4/01:00:0e:00:00/40 tag 6 ncq 131072 in
res 41/84:00:e8:ee:a4/00:01:0e:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 56.899029] ata1.00: status: { DRDY ERR }
[ 56.899072] ata1.00: error: { ICRC ABRT }
[ 56.899121] ata1: hard resetting link
[ 57.218560] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 57.311513] ata1.00: configured for UDMA/33
[ 57.311542] ata1: EH complete
[ 57.355664] ata1.00: exception Emask 0x0 SAct 0x500 SErr 0x0 action 0x6
[ 57.355754] ata1.00: irq_stat 0x40000008
[ 57.355806] ata1.00: failed command: READ FPDMA QUEUED
[ 57.355873] ata1.00: cmd 60/58:50:00:ec:a4/00:00:0e:00:00/40 tag 10 ncq 45056 in
res 41/84:58:1a:ec:a4/00:00:0e:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 57.356044] ata1.00: status: { DRDY ERR }
[ 57.356091] ata1.00: error: { ICRC ABRT }
[ 57.356145] ata1: hard resetting link
[ 57.675608] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 57.766781] ata1.00: configured for UDMA/33
[ 57.766816] ata1: EH complete
[ 57.806077] ata1.00: exception Emask 0x0 SAct 0x3000 SErr 0x0 action 0x6
[ 57.806134] ata1.00: irq_stat 0x40000008
[ 57.806164] ata1.00: failed command: READ FPDMA QUEUED
[ 57.806203] ata1.00: cmd 60/00:68:70:24:a5/01:00:0e:00:00/40 tag 13 ncq 131072 in
res 41/84:00:f2:24:a5/00:01:0e:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 57.806302] ata1.00: status: { DRDY ERR }
[ 57.806330] ata1.00: error: { ICRC ABRT }
[ 57.806362] ata1: hard resetting link
[ 58.125961] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 58.211103] ata1.00: configured for UDMA/33
[ 58.211156] ata1: EH complete
[ 58.249769] ata1.00: exception Emask 0x0 SAct 0x18000 SErr 0x0 action 0x6
[ 58.249854] ata1.00: irq_stat 0x40000008
[ 58.249901] ata1.00: failed command: READ FPDMA QUEUED
[ 58.249962] ata1.00: cmd 60/00:80:20:27:a5/01:00:0e:00:00/40 tag 16 ncq 131072 in
res 41/84:00:a2:27:a5/00:01:0e:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 58.255626] ata1.00: status: { DRDY ERR }
[ 58.258790] ata1.00: error: { ICRC ABRT }
[ 58.261924] ata1: hard resetting link
[ 58.579657] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 58.666164] ata1.00: configured for UDMA/33
[ 58.666199] ata1: EH complete
[ 58.716707] ata1.00: exception Emask 0x0 SAct 0x4000000 SErr 0x0 action 0x6
[ 58.718539] ata1.00: irq_stat 0x40000008
[ 58.720328] ata1.00: failed command: READ FPDMA QUEUED
[ 58.722121] ata1.00: cmd 60/00:d0:68:92:5c/01:00:0f:00:00/40 tag 26 ncq 131072 in
res 41/84:00:76:92:5c/00:01:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 58.725736] ata1.00: status: { DRDY ERR }
[ 58.727553] ata1.00: error: { ICRC ABRT }
[ 58.728965] ata1: hard resetting link
[ 59.046670] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 59.132488] ata1.00: configured for UDMA/33
[ 59.132515] ata1: EH complete
[ 59.180459] ata1.00: exception Emask 0x0 SAct 0x20000000 SErr 0x0 action 0x6
[ 59.181979] ata1.00: irq_stat 0x40000008
[ 59.182990] ata1.00: failed command: READ FPDMA QUEUED
[ 59.183943] ata1.00: cmd 60/f8:e8:68:93:5c/00:00:0f:00:00/40 tag 29 ncq 126976 in
res 41/84:f8:6a:93:5c/00:00:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 59.185831] ata1.00: status: { DRDY ERR }
[ 59.186778] ata1.00: error: { ICRC ABRT }
[ 59.187715] ata1: hard resetting link
[ 59.507035] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 59.610051] ata1.00: configured for UDMA/33
[ 59.610080] ata1: EH complete
[ 59.661766] ata1.00: exception Emask 0x0 SAct 0x80 SErr 0x0 action 0x6
[ 59.663154] ata1.00: irq_stat 0x40000008
[ 59.664089] ata1.00: failed command: READ FPDMA QUEUED
[ 59.665027] ata1.00: cmd 60/98:38:60:94:5c/00:00:0f:00:00/40 tag 7 ncq 77824 in
res 41/84:98:64:94:5c/00:00:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 59.666916] ata1.00: status: { DRDY ERR }
[ 59.669774] ata1.00: error: { ICRC ABRT }
[ 59.672954] ata1: hard resetting link
[ 59.990695] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 60.087554] ata1.00: configured for UDMA/33
[ 60.087600] ata1: EH complete
[ 60.217903] ata1.00: exception Emask 0x0 SAct 0x80 SErr 0x0 action 0x6
[ 60.219413] ata1.00: irq_stat 0x40000008
[ 60.220456] ata1.00: failed command: READ FPDMA QUEUED
[ 60.221440] ata1.00: cmd 60/20:38:00:1b:3e/00:00:0f:00:00/40 tag 7 ncq 16384 in
res 41/84:20:18:1b:3e/00:00:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 60.223332] ata1.00: status: { DRDY ERR }
[ 60.224269] ata1.00: error: { ICRC ABRT }
[ 60.225206] ata1: hard resetting link
[ 60.544531] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 60.653686] ata1.00: configured for UDMA/33
[ 60.653713] ata1: EH complete
[ 60.701540] ata1.00: exception Emask 0x0 SAct 0x400 SErr 0x0 action 0x6
[ 60.703016] ata1.00: irq_stat 0x40000008
[ 60.704106] ata1.00: failed command: READ FPDMA QUEUED
[ 60.705056] ata1.00: cmd 60/88:50:78:1b:3e/00:00:0f:00:00/40 tag 10 ncq 69632 in
res 41/84:88:78:1b:3e/00:00:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 60.706949] ata1.00: status: { DRDY ERR }
[ 60.707884] ata1.00: error: { ICRC ABRT }
[ 60.708824] ata1: hard resetting link
[ 61.028237] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 61.142293] ata1.00: configured for UDMA/33
[ 61.142319] ata1: EH complete
[ 61.195399] ata1.00: exception Emask 0x0 SAct 0x8000 SErr 0x0 action 0x6
[ 61.197750] ata1.00: irq_stat 0x40000008
[ 61.200089] ata1.00: failed command: READ FPDMA QUEUED
[ 61.201690] ata1.00: cmd 60/20:78:10:39:38/00:00:0f:00:00/40 tag 15 ncq 16384 in
res 41/84:20:14:39:38/00:00:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 61.204897] ata1.00: status: { DRDY ERR }
[ 61.206484] ata1.00: error: { ICRC ABRT }
[ 61.208071] ata1: hard resetting link
[ 61.525313] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 61.630818] ata1.00: configured for UDMA/33
[ 61.630845] ata1: EH complete
[ 61.675724] ata1.00: exception Emask 0x0 SAct 0x40000 SErr 0x0 action 0x6
[ 61.677345] ata1.00: irq_stat 0x40000008
[ 61.678943] ata1.00: failed command: READ FPDMA QUEUED
[ 61.680539] ata1.00: cmd 60/50:90:30:39:38/00:00:0f:00:00/40 tag 18 ncq 40960 in
res 41/84:50:70:39:38/00:00:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 61.683756] ata1.00: status: { DRDY ERR }
[ 61.685369] ata1.00: error: { ICRC ABRT }
[ 61.686586] ata1: hard resetting link
[ 62.005676] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 62.108289] ata1.00: configured for UDMA/33
[ 62.108316] ata1: EH complete
[ 62.162783] ata1.00: exception Emask 0x0 SAct 0x400000 SErr 0x0 action 0x6
[ 62.164411] ata1.00: irq_stat 0x40000008
[ 62.166015] ata1.00: failed command: READ FPDMA QUEUED
[ 62.167617] ata1.00: cmd 60/20:b0:d8:c3:3d/00:00:0f:00:00/40 tag 22 ncq 16384 in
res 41/84:20:d8:c3:3d/00:00:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 62.170837] ata1.00: status: { DRDY ERR }
[ 62.172433] ata1.00: error: { ICRC ABRT }
[ 62.173698] ata1: hard resetting link
[ 62.492749] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 62.607944] ata1.00: configured for UDMA/33
[ 62.607974] ata1: EH completeOutput of smartctl -a /dev/sda
smartctl 6.3 2014-07-26 r3976 [x86_64-linux-3.19.3-3-ARCH] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Laptop SSHD
Device Model: ST1000LM014-SSHD-8GB
Serial Number: W3829AM6
LU WWN Device Id: 5 000c50 07be01372
Firmware Version: LVD3
User Capacity: 1,000,204,886,016 bytes [1,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Sun May 10 11:12:02 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 150) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 198) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x1081) SCT Status supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 117 099 006 Pre-fail Always - 158141600
3 Spin_Up_Time 0x0003 097 097 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 429
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 073 060 030 Pre-fail Always - 4319585187
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 1864
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 437
184 End-to-End_Error 0x0032 089 089 099 Old_age Always FAILING_NOW 11
187 Reported_Uncorrect 0x0032 098 098 000 Old_age Always - 2
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 069 052 045 Old_age Always - 31 (Min/Max 25/31)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 50
193 Load_Cycle_Count 0x0032 097 097 000 Old_age Always - 6179
194 Temperature_Celsius 0x0022 031 048 000 Old_age Always - 31 (0 19 0 0 0)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 13 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 13 occurred at disk power-on lifetime: 1779 hours (74 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 10 ff ff ff 4f 00 09:58:41.053 READ FPDMA QUEUED
60 00 b0 ff ff ff 4f 00 09:58:41.053 READ FPDMA QUEUED
60 00 30 ff ff ff 4f 00 09:58:41.053 READ FPDMA QUEUED
ea 00 00 00 00 00 a0 00 09:58:40.403 FLUSH CACHE EXT
61 00 08 ff ff ff 4f 00 09:58:40.403 WRITE FPDMA QUEUED
Error 12 occurred at disk power-on lifetime: 1722 hours (71 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 00:01:28.048 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 00:01:28.048 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:01:28.047 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 00:01:28.047 READ FPDMA QUEUED
60 00 30 50 3a c5 4e 00 00:01:28.045 READ FPDMA QUEUED
Error 11 occurred at disk power-on lifetime: 1537 hours (64 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 00:00:35.199 READ FPDMA QUEUED
60 00 20 ff ff ff 4f 00 00:00:35.198 READ FPDMA QUEUED
60 00 08 10 10 2b 4f 00 00:00:35.188 READ FPDMA QUEUED
60 00 e0 20 e0 78 4f 00 00:00:35.187 READ FPDMA QUEUED
60 00 90 68 e1 78 4f 00 00:00:35.185 READ FPDMA QUEUED
Error 10 occurred at disk power-on lifetime: 1525 hours (63 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 a0 ff ff ff 4f 00 00:00:15.374 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:00:15.373 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:00:15.373 READ FPDMA QUEUED
60 00 80 ff ff ff 4f 00 00:00:15.370 READ FPDMA QUEUED
60 00 68 ff ff ff 4f 00 00:00:15.370 READ FPDMA QUEUED
Error 9 occurred at disk power-on lifetime: 1525 hours (63 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 e0 9e 31 4f 00 00:00:15.146 READ FPDMA QUEUED
60 00 a8 ff ff ff 4f 00 00:00:15.073 READ FPDMA QUEUED
60 00 18 ff ff ff 4f 00 00:00:15.072 READ FPDMA QUEUED
60 00 98 ff ff ff 4f 00 00:00:15.072 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 00:00:15.068 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.Is this software bug or hard drive failure? Thanks in advance.
Offline
#2 2015-05-10 16:16:12
- ewaller
- Administrator
- From: Pasadena, CA
- Registered: 2009-07-13
- Posts: 20,384
Re: ATA bus error
Those seek errors and raw read error rates are astronomical. This is a hard drive failure.
Nothing is too wonderful to be true, if it be consistent with the laws of nature -- Michael Faraday
The shortest way to ruin a country is to give power to demagogues.— Dionysius of Halicarnassus
---
How to Ask Questions the Smart Way
Offline
#3 2015-05-10 20:02:41
- jsoy9pQbYVNu5nfU
- Member
- Registered: 2013-04-19
- Posts: 108
Re: ATA bus error
ewaller wrote:
Those seek errors and raw read error rates are astronomical. This is a hard drive failure.
Not necessarily, this is a Seagate hard drive. AFAIK Seek Error Rate and Raw Read Error Rate are 48bit values where the lower 24bit encode the total number of sectors read/saught (which overflows to zero) and the upper 24bit encode the acutal errors.
smartctl -v 1,hex48 -v 7,hex48 -a /dev/sdashould display OP's data in a usuable format.
In fact, I turned my recently purchased laptop in for a hard disk replacement of almost the same type as OP (ST500LM000-SSHD-8GB) twice, but all three drives of this type I had provided SMART values which were more of an oracle rather than data useful for monitoring purposes. Forums are full with people unsure about what to do with this kind of drives. If you google for the End-to-End errors with Seagate drives (here marked as FAILING!), you'll find people reporting that Seagate's own tools do not report any errors despite the attribute in question being reported by monitoring tools just as bad... Seagate is the horror. So, I'd say that it is rather uncertain whether the SMART values are connected to the actual drive failing or a faulty cable.
OP, did you see these errors from the beginning or after a certain time, or perhaps after a kernel upgrade? Did you check the drive's cable? What was the situation before these errors showed up (maybe under Windows?)
Offline
#4 2015-05-10 22:35:45
- ewaller
- Administrator
- From: Pasadena, CA
- Registered: 2009-07-13
- Posts: 20,384
Re: ATA bus error
I'd never heard that; So much for trusting the instrumentation. I'll watch this thread and see how it plays out.
Nothing is too wonderful to be true, if it be consistent with the laws of nature -- Michael Faraday
The shortest way to ruin a country is to give power to demagogues.— Dionysius of Halicarnassus
---
How to Ask Questions the Smart Way
Offline
#5 2015-05-10 22:39:49
- ewaller
- Administrator
- From: Pasadena, CA
- Registered: 2009-07-13
- Posts: 20,384
Re: ATA bus error
Okay, point of reference. I too have a Seagate drive, but I don't see the issue :?
ewaller@turing /sys/class/backlight 1063 %sudo smartctl -a /dev/sda
[sudo] password for ewaller:
smartctl 6.3 2014-07-26 r3976 [x86_64-linux-4.0.2-1-ARCH] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: ST2000LM003 HN-M201RAD
Serial Number: S34LJ9BG202317
LU WWN Device Id: 5 0004cf 20f40fd49
Firmware Version: 2BC10001
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sun May 10 15:36:03 2015 PDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (22320) seconds.
Offline data collection
capabilities: (0x51) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 372) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 0
2 Throughput_Performance 0x0027 252 252 000 Pre-fail Always - 0
3 Spin_Up_Time 0x0023 091 090 025 Pre-fail Always - 2880
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 123
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x002f 252 252 051 Pre-fail Always - 0
8 Seek_Time_Performance 0x0025 252 252 015 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 334
10 Spin_Retry_Count 0x0033 252 252 051 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 127
181 Program_Fail_Cnt_Total 0x0022 100 100 000 Old_age Always - 127774
183 Runtime_Bad_Block 0x0032 252 252 010 Old_age Always - 0
184 End-to-End_Error 0x0033 252 252 097 Pre-fail Always - 0
186 Unknown_Attribute 0x0032 252 252 000 Old_age Always - 0
187 Reported_Uncorrect 0x0032 252 252 000 Old_age Always - 0
188 Command_Timeout 0x0032 252 252 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0002 067 056 040 Old_age Always - 33 (Min/Max 17/44)
191 G-Sense_Error_Rate 0x0022 100 100 000 Old_age Always - 432
192 Power-Off_Retract_Count 0x0022 100 100 000 Old_age Always - 3
193 Load_Cycle_Count 0x0032 092 092 000 Old_age Always - 83598
194 Temperature_Celsius 0x0002 064 056 000 Old_age Always - 33 (Min/Max 17/44)
195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age Always - 0
196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 252 252 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x002a 100 100 000 Old_age Always - 10
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
ewaller@turing /sys/class/backlight 1064 %Nothing is too wonderful to be true, if it be consistent with the laws of nature -- Michael Faraday
The shortest way to ruin a country is to give power to demagogues.— Dionysius of Halicarnassus
---
How to Ask Questions the Smart Way
Offline
#6 2015-05-11 06:06:31
- jsoy9pQbYVNu5nfU
- Member
- Registered: 2013-04-19
- Posts: 108
Re: ATA bus error
Here's mine, it looks like all the drives I had before from the same model line looked like:
smartctl 6.3 2014-07-26 r3976 [x86_64-linux-3.19.7-1-ck] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Laptop SSHD
Device Model: ST500LM000-SSHD-8GB
Serial Number: W761FLG1
LU WWN Device Id: 5 000c50 07c473b34
Firmware Version: LIV5
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS, ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Mon May 11 08:00:51 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 139) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 100) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x1081) SCT Status supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 111 099 034 Pre-fail Always - 0x00000262e8a0
3 Spin_Up_Time 0x0003 099 099 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 147
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 066 060 030 Pre-fail Always - 0x00010039c4b3
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 747 (221 229 0)
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 147
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 099 000 Old_age Always - 3
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 067 048 045 Old_age Always - 33 (Min/Max 23/33)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 5
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 188
194 Temperature_Celsius 0x0022 033 052 000 Old_age Always - 33 (0 16 0 0 0)
196 Reallocated_Event_Count 0x000f 100 100 030 Pre-fail Always - 754 (54398 0)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 744 -
# 2 Vendor (0x50) Aborted by host 90% 580 -
# 3 Short offline Completed without error 00% 580 -
# 4 Extended offline Completed without error 00% 4 -
# 5 Conveyance offline Completed without error 00% 3 -
# 6 Short offline Completed without error 00% 2 -
# 7 Short offline Completed without error 00% 2 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.You can tell that my Seek Error Rate (although not Raw Reads) is worrying even according to the interpretation I gave (likewise, the Reallocated Event Count), but the service people (Lenovo Service, it's a TP) refuse to exchange the drive a third time since short and long SMART test routines do not error out. As I said, I do not have verified information and do not know anybody who does know how to read these SMART values correctly...I gave up and am just waiting for the drive to fail.
Last edited by jsoy9pQbYVNu5nfU (2015-05-11 06:07:13)
Offline
#7 2015-05-11 10:24:56
- Ivan1pl
- Member
- Registered: 2012-03-12
- Posts: 3
Re: ATA bus error
Thanks for your answers.
2ion wrote:
Not necessarily, this is a Seagate hard drive. AFAIK Seek Error Rate and Raw Read Error Rate are 48bit values where the lower 24bit encode the total number of sectors read/saught (which overflows to zero) and the upper 24bit encode the acutal errors.
smartctl -v 1,hex48 -v 7,hex48 -a /dev/sdashould display OP's data in a usuable format.
In fact, I turned my recently purchased laptop in for a hard disk replacement of almost the same type as OP (ST500LM000-SSHD-8GB) twice, but all three drives of this type I had provided SMART values which were more of an oracle rather than data useful for monitoring purposes. Forums are full with people unsure about what to do with this kind of drives. If you google for the End-to-End errors with Seagate drives (here marked as FAILING!), you'll find people reporting that Seagate's own tools do not report any errors despite the attribute in question being reported by monitoring tools just as bad... Seagate is the horror. So, I'd say that it is rather uncertain whether the SMART values are connected to the actual drive failing or a faulty cable.
OP, did you see these errors from the beginning or after a certain time, or perhaps after a kernel upgrade? Did you check the drive's cable? What was the situation before these errors showed up (maybe under Windows?)
smartctl -v 1,hex48 -v 7,hex48 -a /dev/sda
smartctl 6.3 2014-07-26 r3976 [x86_64-linux-3.19.3-3-ARCH] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Laptop SSHD
Device Model: ST1000LM014-SSHD-8GB
Serial Number: W3829AM6
LU WWN Device Id: 5 000c50 07be01372
Firmware Version: LVD3
User Capacity: 1,000,204,886,016 bytes [1,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Mon May 11 12:09:29 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 150) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 198) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x1081) SCT Status supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 115 099 006 Pre-fail Always - 0x000005184840
3 Spin_Up_Time 0x0003 097 097 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 433
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 073 060 030 Pre-fail Always - 0x0001017be679
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 1880
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 441
184 End-to-End_Error 0x0032 089 089 099 Old_age Always FAILING_NOW 11
187 Reported_Uncorrect 0x0032 098 098 000 Old_age Always - 2
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 061 052 045 Old_age Always - 39 (Min/Max 37/39)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 50
193 Load_Cycle_Count 0x0032 097 097 000 Old_age Always - 6282
194 Temperature_Celsius 0x0022 039 048 000 Old_age Always - 39 (0 19 0 0 0)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 13 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 13 occurred at disk power-on lifetime: 1779 hours (74 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 10 ff ff ff 4f 00 09:58:41.053 READ FPDMA QUEUED
60 00 b0 ff ff ff 4f 00 09:58:41.053 READ FPDMA QUEUED
60 00 30 ff ff ff 4f 00 09:58:41.053 READ FPDMA QUEUED
ea 00 00 00 00 00 a0 00 09:58:40.403 FLUSH CACHE EXT
61 00 08 ff ff ff 4f 00 09:58:40.403 WRITE FPDMA QUEUED
Error 12 occurred at disk power-on lifetime: 1722 hours (71 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 00:01:28.048 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 00:01:28.048 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:01:28.047 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 00:01:28.047 READ FPDMA QUEUED
60 00 30 50 3a c5 4e 00 00:01:28.045 READ FPDMA QUEUED
Error 11 occurred at disk power-on lifetime: 1537 hours (64 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 00:00:35.199 READ FPDMA QUEUED
60 00 20 ff ff ff 4f 00 00:00:35.198 READ FPDMA QUEUED
60 00 08 10 10 2b 4f 00 00:00:35.188 READ FPDMA QUEUED
60 00 e0 20 e0 78 4f 00 00:00:35.187 READ FPDMA QUEUED
60 00 90 68 e1 78 4f 00 00:00:35.185 READ FPDMA QUEUED
Error 10 occurred at disk power-on lifetime: 1525 hours (63 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 a0 ff ff ff 4f 00 00:00:15.374 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:00:15.373 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:00:15.373 READ FPDMA QUEUED
60 00 80 ff ff ff 4f 00 00:00:15.370 READ FPDMA QUEUED
60 00 68 ff ff ff 4f 00 00:00:15.370 READ FPDMA QUEUED
Error 9 occurred at disk power-on lifetime: 1525 hours (63 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 e0 9e 31 4f 00 00:00:15.146 READ FPDMA QUEUED
60 00 a8 ff ff ff 4f 00 00:00:15.073 READ FPDMA QUEUED
60 00 18 ff ff ff 4f 00 00:00:15.072 READ FPDMA QUEUED
60 00 98 ff ff ff 4f 00 00:00:15.072 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 00:00:15.068 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 1871 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.These errors just appeared, not after upgrade and I didn't get them in the beginning. The situation before errors - everything worked exactly the same, I see no difference in performance, except that few seconds long freeze that sometimes happen. Can't tell about Windows, I have it pre-installed but never used it so I can't compare. I didn't check the cable, and I'd rather not do that - I don't want to mess with hardware, if I do something wrong I lose the warranty. If something is wrong then I'd rather have it checked and fixed by someone who knows how to do that (and for free, because I still have the warranty).
Offline
#8 2015-05-11 15:49:30
- jsoy9pQbYVNu5nfU
- Member
- Registered: 2013-04-19
- Posts: 108
Re: ATA bus error
Indeed, the ATA errors seem to occur periodically and not persistently. Since the SMART error log is populated and your error rates even in the upper bytes are not zero (neither is mine, but oh well), you should have no problem at all getting your computer serviced! As ewaller said, this is likely a hardware problem. Maybe ask if you can get a different hard drive type as a replacement, like a Hitachi.
Offline
#9 2015-05-11 21:06:10
- rlees85
- Member
- From: Daventry, UK
- Registered: 2015-04-29
- Posts: 98
- Website
Re: ATA bus error
Given you have no bad sectors but have things like 'END-TO-END' errors, maybe try a different SATA cable or even SATA port if possible?
Also what is an SSHD? Is it one of those hybrid things? I've only ever known those to give people grief to be honest best either getting a SSD or a HDD.
I know on Seagate HARD DISKs the stupidly high looking raw-read error rates are perfectly normal as mentioned above. I wouldn't spend too much time worrying about those...
Also Google "NCQ bug" as a lot of SSD/SSHDs seem to have this. The 'work-around' is to disable NCQ Linky
Edit: if you do try the above, make sure you update your grub config file after making changes to /etc/default/grub !!
# grub-mkconfig -o /boot/grub/grub.cfgLast edited by rlees85 (2015-05-11 21:31:38)
Offline
Pages: 1