You are not logged in.
- Topics: Active | Unanswered
#1 2015-08-22 13:37:16
- hotvic
- Member
- Registered: 2013-02-11
- Posts: 109
recently high X CPU usage
Recently the X is using a lot of CPU ~29-60% of CPU it occurs randomly but almost all time.
before I'm using arch and the cpu usage is about~5-6% so I switched to fedora by other reasons(and of course low cpu usage just like was on arch), and now switched back to arch and is suffering this.
Just after installed everything, X server, drivers, and window manager (awesome-wm) I got serious graphic corruptions. so I switched AccelMethod to "uxa" the corruptions ends.
but now its using a lot of CPU, I don't know if its beacause I'm using "uxa".
previous on arch I was using sna and on fedora too. (almost sure rsrs, since I never changed this setting).
it's a...
$ lspci
00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09)
# the processor is a Celeron 847
# the module is, of cource, i915
# the module parameters
Parameters:
disable_display = "N"
disable_power_well = "1"
disable_vtd_wa = "N"
enable_cmd_parser = "1"
enable_execlists = "0"
enable_fbc = "-1"
enable_hangcheck = "Y"
enable_ips = "1"
enable_ppgtt = "1"
enable_psr = "0"
enable_rc6 = "0"
fastboot = "N"
invert_brightness = "0"
load_detect_test = "N"
lvds_channel_mode = "0"
lvds_downclock = "0"
lvds_use_ssc = "-1"
mmio_debug = "0"
modeset = "-1"
nuclear_pageflip = "N"
panel_ignore_lid = "1"
prefault_disable = "N"
preliminary_hw_support= "0"
reset = "Y"
semaphores = "-1"
use_mmio_flip = "0"
vbt_sdvo_panel_type = "-1"
verbose_state_checks= "Y"
# all parameters are default ones, except by enable_rc6the server configuration is only:
~ cat /etc/X11/xorg.conf.d/20-intel.conf
Section "Device"
Identifier "Intel Graphics"
Driver "intel"
Option "AccelMethod" "uxa"
#Option "AccelMethod" "sna"
EndSectionThanks to all 
Offline
#2 2015-08-22 13:38:57
- karol
- Archivist
- Registered: 2009-05-06
- Posts: 25,440
Re: recently high X CPU usage
How did you measure cpu utilization by X?
Offline
#3 2015-08-22 13:49:25
- hotvic
- Member
- Registered: 2013-02-11
- Posts: 109
Re: recently high X CPU usage
I'm using htop, karol
Edit:
forgot to mention, when I launch htop in urxvt the CPU goes to top absurd values.
Last edited by hotvic (2015-08-22 13:53:37)
Offline
#4 2015-08-22 13:51:57
- karol
- Archivist
- Registered: 2009-05-06
- Posts: 25,440
Re: recently high X CPU usage
Anything interesting in the logs or systemd's journal?
Offline
#5 2015-08-22 13:54:54
- hotvic
- Member
- Registered: 2013-02-11
- Posts: 109
Re: recently high X CPU usage
Nothing! AFAIK there's nothing "unnatural"
Offline
#6 2015-08-22 14:01:37
- karol
- Archivist
- Registered: 2009-05-06
- Posts: 25,440
Re: recently high X CPU usage
I'm using uxa too and cpu utilization is around 0% unless I have firefox with a few tabs open - it then jumps to around 5%.
Post your X log.
Offline
#7 2015-08-22 14:14:40
- hotvic
- Member
- Registered: 2013-02-11
- Posts: 109
Re: recently high X CPU usage
Xorg log:
[ 28.437]
X.Org X Server 1.17.2
Release Date: 2015-06-16
[ 28.437] X Protocol Version 11, Revision 0
[ 28.437] Build Operating System: Linux 4.0.4-2-ARCH x86_64
[ 28.437] Current Operating System: Linux Victor 4.1.4-1-ARCH #1 SMP PREEMPT Mon Aug 3 21:30:37 UTC 2015 x86_64
[ 28.437] Kernel command line: initrd=\initramfs-linux.img rw root=/dev/sda3
[ 28.437] Build Date: 17 July 2015 05:38:19PM
[ 28.437]
[ 28.437] Current version of pixman: 0.32.6
[ 28.437] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 28.437] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 28.438] (==) Log file: "/home/victor/.local/share/xorg/Xorg.0.log", Time: Fri Aug 14 01:23:39 2015
[ 28.478] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 28.478] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 28.525] (==) No Layout section. Using the first Screen section.
[ 28.525] (==) No screen section available. Using defaults.
[ 28.525] (**) |-->Screen "Default Screen Section" (0)
[ 28.525] (**) | |-->Monitor "<default monitor>"
[ 28.538] (==) No device specified for screen "Default Screen Section".
Using the first device section listed.
[ 28.538] (**) | |-->Device "Intel Graphics"
[ 28.538] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 28.539] (==) Automatically adding devices
[ 28.539] (==) Automatically enabling devices
[ 28.539] (==) Automatically adding GPU devices
[ 28.539] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 28.539] Entry deleted from font path.
[ 28.539] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 28.539] Entry deleted from font path.
[ 28.539] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 28.539] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 28.539] Entry deleted from font path.
[ 28.539] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 28.539] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/OTF/
[ 28.539] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 28.539] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 28.549] (II) Loader magic: 0x817d60
[ 28.550] (II) Module ABI versions:
[ 28.550] X.Org ANSI C Emulation: 0.4
[ 28.550] X.Org Video Driver: 19.0
[ 28.550] X.Org XInput driver : 21.1
[ 28.550] X.Org Server Extension : 9.0
[ 28.555] (II) systemd-logind: took control of session /org/freedesktop/login1/session/c2
[ 28.556] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 28.557] (II) systemd-logind: got fd for /dev/dri/card0 226:0 fd 9 paused 0
[ 28.559] (--) PCI:*(0:0:2:0) 8086:0106:1565:110f rev 9, Mem @ 0xf7800000/4194304, 0xe0000000/268435456, I/O @ 0x0000f000/64
[ 28.559] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 28.569] (II) LoadModule: "glx"
[ 28.619] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 28.651] (II) Module glx: vendor="X.Org Foundation"
[ 28.651] compiled for 1.17.2, module version = 1.0.0
[ 28.651] ABI class: X.Org Server Extension, version 9.0
[ 28.651] (==) AIGLX enabled
[ 28.651] (II) LoadModule: "intel"
[ 28.651] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 28.737] (II) Module intel: vendor="X.Org Foundation"
[ 28.737] compiled for 1.17.2, module version = 2.99.917
[ 28.737] Module class: X.Org Video Driver
[ 28.738] ABI class: X.Org Video Driver, version 19.0
[ 28.738] (II) intel: Driver for Intel(R) Integrated Graphics Chipsets:
i810, i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G,
915G, E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM,
Pineview G, 965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33,
GM45, 4 Series, G45/G43, Q45/Q43, G41, B43
[ 28.739] (II) intel: Driver for Intel(R) HD Graphics: 2000-6000
[ 28.739] (II) intel: Driver for Intel(R) Iris(TM) Graphics: 5100, 6100
[ 28.739] (II) intel: Driver for Intel(R) Iris(TM) Pro Graphics: 5200, 6200, P6300
[ 28.739] (++) using VT number 2
[ 28.739] xf86EnableIOPorts: failed to set IOPL for I/O (Operation not permitted)
[ 28.752] (WW) VGA arbiter: cannot open kernel arbiter, no multi-card support
[ 28.752] (II) intel(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 28.752] (==) intel(0): Depth 24, (--) framebuffer bpp 32
[ 28.752] (==) intel(0): RGB weight 888
[ 28.752] (==) intel(0): Default visual is TrueColor
[ 28.752] (**) intel(0): Option "AccelMethod" "uxa"
[ 28.752] (--) intel(0): Integrated Graphics Chipset: Intel(R) HD Graphics 2000
[ 28.753] (**) intel(0): Relaxed fencing enabled
[ 28.753] (**) intel(0): Wait on SwapBuffers? enabled
[ 28.753] (**) intel(0): Triple buffering? enabled
[ 28.753] (**) intel(0): Framebuffer tiled
[ 28.753] (**) intel(0): Pixmaps tiled
[ 28.753] (**) intel(0): 3D buffers tiled
[ 28.753] (**) intel(0): SwapBuffers wait enabled
[ 28.753] (==) intel(0): video overlay key set to 0x101fe
[ 28.766] (II) intel(0): Output VGA1 has no monitor section
[ 28.767] (II) intel(0): Output HDMI1 has no monitor section
[ 28.767] (II) intel(0): Output DP1 has no monitor section
[ 28.780] (WW) EDID timing clock 85.50 exceeds claimed max 85MHz, fixing
[ 28.780] (II) intel(0): EDID for output VGA1
[ 28.780] (II) intel(0): Manufacturer: PHL Model: 875 Serial#: 51495
[ 28.780] (II) intel(0): Year: 2010 Week: 27
[ 28.780] (II) intel(0): EDID Version: 1.3
[ 28.780] (II) intel(0): Analog Display Input, Input Voltage Level: 0.700/0.700 V
[ 28.780] (II) intel(0): Sync: Separate
[ 28.780] (II) intel(0): Max Image Size [cm]: horiz.: 34 vert.: 19
[ 28.780] (II) intel(0): Gamma: 2.20
[ 28.780] (II) intel(0): DPMS capabilities: Off; RGB/Color Display
[ 28.780] (II) intel(0): First detailed timing is preferred mode
[ 28.780] (II) intel(0): redX: 0.635 redY: 0.335 greenX: 0.281 greenY: 0.597
[ 28.780] (II) intel(0): blueX: 0.153 blueY: 0.085 whiteX: 0.312 whiteY: 0.328
[ 28.780] (II) intel(0): Supported established timings:
[ 28.780] (II) intel(0): 720x400@70Hz
[ 28.780] (II) intel(0): 640x480@60Hz
[ 28.780] (II) intel(0): 640x480@67Hz
[ 28.780] (II) intel(0): 640x480@72Hz
[ 28.780] (II) intel(0): 640x480@75Hz
[ 28.780] (II) intel(0): 800x600@56Hz
[ 28.780] (II) intel(0): 800x600@60Hz
[ 28.780] (II) intel(0): 800x600@72Hz
[ 28.780] (II) intel(0): 800x600@75Hz
[ 28.780] (II) intel(0): 832x624@75Hz
[ 28.780] (II) intel(0): 1024x768@60Hz
[ 28.780] (II) intel(0): 1024x768@70Hz
[ 28.780] (II) intel(0): 1024x768@75Hz
[ 28.780] (II) intel(0): Manufacturer's mask: 0
[ 28.780] (II) intel(0): Supported standard timings:
[ 28.780] (II) intel(0): #0: hsize: 640 vsize 400 refresh: 70 vid: 2609
[ 28.780] (II) intel(0): #1: hsize: 1024 vsize 768 refresh: 72 vid: 19553
[ 28.780] (II) intel(0): Supported detailed timing:
[ 28.781] (II) intel(0): clock: 85.5 MHz Image Size: 344 x 194 mm
[ 28.781] (II) intel(0): h_active: 1366 h_sync: 1436 h_sync_end 1579 h_blank_end 1792 h_border: 0
[ 28.781] (II) intel(0): v_active: 768 v_sync: 771 v_sync_end 774 v_blanking: 798 v_border: 0
[ 28.781] (II) intel(0): Serial No: AF20942051495
[ 28.781] (II) intel(0): Monitor name: Philips 160VW
[ 28.781] (II) intel(0): Ranges: V min: 55 V max: 75 Hz, H min: 30 H max: 60 kHz, PixClock max 86 MHz
[ 28.781] (II) intel(0): EDID (in hex):
[ 28.781] (II) intel(0): 00ffffffffffff00410c750827c90000
[ 28.781] (II) intel(0): 1b140103682213782ab370a255489827
[ 28.781] (II) intel(0): 155054bfee00310a614c010101010101
[ 28.781] (II) intel(0): 010101010101662156aa51001e30468f
[ 28.781] (II) intel(0): 330058c21000001e000000ff00414632
[ 28.781] (II) intel(0): 30393432303531343935000000fc0050
[ 28.781] (II) intel(0): 68696c697073203136305657000000fd
[ 28.781] (II) intel(0): 00374b1e3c08000a2020202020200046
[ 28.781] (II) intel(0): Printing probed modes for output VGA1
[ 28.781] (II) intel(0): Modeline "1366x768"x59.8 85.50 1366 1436 1579 1792 768 771 774 798 +hsync +vsync (47.7 kHz eP)
[ 28.781] (II) intel(0): Modeline "1024x768"x75.1 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.1 kHz e)
[ 28.781] (II) intel(0): Modeline "1024x768"x72.0 78.44 1024 1080 1192 1360 768 769 772 801 -hsync +vsync (57.7 kHz)
[ 28.781] (II) intel(0): Modeline "1024x768"x70.1 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e)
[ 28.781] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 28.781] (II) intel(0): Modeline "832x624"x74.6 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e)
[ 28.781] (II) intel(0): Modeline "800x600"x72.2 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e)
[ 28.781] (II) intel(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 28.781] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 28.781] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 28.781] (II) intel(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 28.781] (II) intel(0): Modeline "640x480"x72.8 31.50 640 664 704 832 480 489 491 520 -hsync -vsync (37.9 kHz e)
[ 28.781] (II) intel(0): Modeline "640x480"x66.7 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e)
[ 28.781] (II) intel(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 28.781] (II) intel(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 28.782] (II) intel(0): EDID for output HDMI1
[ 28.782] (II) intel(0): EDID for output DP1
[ 28.782] (II) intel(0): Output VGA1 connected
[ 28.782] (II) intel(0): Output HDMI1 disconnected
[ 28.782] (II) intel(0): Output DP1 disconnected
[ 28.782] (II) intel(0): Using exact sizes for initial modes
[ 28.782] (II) intel(0): Output VGA1 using initial mode 1366x768
[ 28.782] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 28.782] (II) intel(0): Kernel page flipping support detected, enabling
[ 28.782] (==) intel(0): DPI set to (96, 96)
[ 28.782] (II) Loading sub module "fb"
[ 28.782] (II) LoadModule: "fb"
[ 28.813] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 28.840] (II) Module fb: vendor="X.Org Foundation"
[ 28.840] compiled for 1.17.2, module version = 1.0.0
[ 28.840] ABI class: X.Org ANSI C Emulation, version 0.4
[ 28.840] (II) Loading sub module "dri2"
[ 28.840] (II) LoadModule: "dri2"
[ 28.840] (II) Module "dri2" already built-in
[ 28.840] (==) Depth 24 pixmap format is 32 bpp
[ 28.840] (II) intel(0): Allocated new frame buffer 1366x768 stride 5632, tiled
[ 28.867] (II) UXA(0): Driver registered support for the following operations:
[ 28.867] (II) solid
[ 28.867] (II) copy
[ 28.867] (II) composite (RENDER acceleration)
[ 28.867] (II) put_image
[ 28.867] (II) get_image
[ 28.867] (II) intel(0): [DRI2] Setup complete
[ 28.867] (II) intel(0): [DRI2] DRI driver: i965
[ 28.867] (II) intel(0): [DRI2] VDPAU driver: va_gl
[ 28.867] (==) intel(0): Backing store enabled
[ 28.867] (==) intel(0): Silken mouse enabled
[ 28.875] (II) intel(0): Initializing HW Cursor
[ 28.875] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 28.881] (==) intel(0): DPMS enabled
[ 28.881] (==) intel(0): Intel XvMC decoder enabled
[ 28.882] (II) intel(0): Set up textured video
[ 28.882] (II) intel(0): [XvMC] xvmc_vld driver initialized.
[ 28.882] (II) intel(0): DRI2: Enabled
[ 28.882] (II) intel(0): DRI3: Disabled
[ 28.882] (==) intel(0): hotplug detection: "enabled"
[ 28.900] (--) RandR disabled
[ 28.954] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[ 28.954] (II) AIGLX: enabled GLX_ARB_create_context
[ 28.954] (II) AIGLX: enabled GLX_ARB_create_context_profile
[ 28.954] (II) AIGLX: enabled GLX_EXT_create_context_es2_profile
[ 28.954] (II) AIGLX: enabled GLX_INTEL_swap_event
[ 28.954] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[ 28.954] (II) AIGLX: enabled GLX_EXT_framebuffer_sRGB
[ 28.954] (II) AIGLX: enabled GLX_ARB_fbconfig_float
[ 28.954] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[ 28.954] (II) AIGLX: enabled GLX_ARB_create_context_robustness
[ 28.954] (II) AIGLX: Loaded and initialized i965
[ 28.954] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 28.955] (II) intel(0): Setting screen physical size to 361 x 203
[ 29.025] (II) config/udev: Adding input device Power Button (/dev/input/event3)
[ 29.025] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 29.025] (**) Power Button: Applying InputClass "system-keyboard"
[ 29.025] (II) LoadModule: "evdev"
[ 29.025] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 29.041] (II) Module evdev: vendor="X.Org Foundation"
[ 29.041] compiled for 1.17.1, module version = 2.9.2
[ 29.041] Module class: X.Org XInput Driver
[ 29.041] ABI class: X.Org XInput driver, version 21.0
[ 29.042] (II) systemd-logind: got fd for /dev/input/event3 13:67 fd 12 paused 0
[ 29.042] (II) Using input driver 'evdev' for 'Power Button'
[ 29.042] (**) Power Button: always reports core events
[ 29.042] (**) evdev: Power Button: Device: "/dev/input/event3"
[ 29.042] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 29.042] (--) evdev: Power Button: Found keys
[ 29.042] (II) evdev: Power Button: Configuring as keyboard
[ 29.042] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input3/event3"
[ 29.042] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 29.043] (**) Option "xkb_rules" "evdev"
[ 29.043] (**) Option "xkb_model" "pc104"
[ 29.043] (**) Option "xkb_layout" "br"
[ 29.043] (**) Option "xkb_options" "grp:alt_shift_toggle"
[ 29.085] (II) config/udev: Adding input device Video Bus (/dev/input/event11)
[ 29.085] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 29.085] (**) Video Bus: Applying InputClass "system-keyboard"
[ 29.086] (II) systemd-logind: got fd for /dev/input/event11 13:75 fd 13 paused 0
[ 29.086] (II) Using input driver 'evdev' for 'Video Bus'
[ 29.086] (**) Video Bus: always reports core events
[ 29.086] (**) evdev: Video Bus: Device: "/dev/input/event11"
[ 29.086] (--) evdev: Video Bus: Vendor 0 Product 0x6
[ 29.086] (--) evdev: Video Bus: Found keys
[ 29.086] (II) evdev: Video Bus: Configuring as keyboard
[ 29.086] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input11/event11"
[ 29.086] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[ 29.086] (**) Option "xkb_rules" "evdev"
[ 29.086] (**) Option "xkb_model" "pc104"
[ 29.086] (**) Option "xkb_layout" "br"
[ 29.086] (**) Option "xkb_options" "grp:alt_shift_toggle"
[ 29.087] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[ 29.087] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 29.088] (**) Power Button: Applying InputClass "system-keyboard"
[ 29.088] (II) systemd-logind: got fd for /dev/input/event2 13:66 fd 14 paused 0
[ 29.088] (II) Using input driver 'evdev' for 'Power Button'
[ 29.088] (**) Power Button: always reports core events
[ 29.088] (**) evdev: Power Button: Device: "/dev/input/event2"
[ 29.088] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 29.088] (--) evdev: Power Button: Found keys
[ 29.088] (II) evdev: Power Button: Configuring as keyboard
[ 29.089] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2/event2"
[ 29.089] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8)
[ 29.089] (**) Option "xkb_rules" "evdev"
[ 29.089] (**) Option "xkb_model" "pc104"
[ 29.089] (**) Option "xkb_layout" "br"
[ 29.089] (**) Option "xkb_options" "grp:alt_shift_toggle"
[ 29.091] (II) config/udev: Adding input device USB OPTICAL MOUSE (/dev/input/event1)
[ 29.091] (**) USB OPTICAL MOUSE: Applying InputClass "evdev pointer catchall"
[ 29.092] (II) systemd-logind: got fd for /dev/input/event1 13:65 fd 15 paused 0
[ 29.092] (II) Using input driver 'evdev' for ' USB OPTICAL MOUSE'
[ 29.092] (**) USB OPTICAL MOUSE: always reports core events
[ 29.092] (**) evdev: USB OPTICAL MOUSE: Device: "/dev/input/event1"
[ 29.092] (--) evdev: USB OPTICAL MOUSE: Vendor 0 Product 0x538
[ 29.092] (--) evdev: USB OPTICAL MOUSE: Found 3 mouse buttons
[ 29.092] (--) evdev: USB OPTICAL MOUSE: Found scroll wheel(s)
[ 29.092] (--) evdev: USB OPTICAL MOUSE: Found relative axes
[ 29.092] (--) evdev: USB OPTICAL MOUSE: Found x and y relative axes
[ 29.092] (II) evdev: USB OPTICAL MOUSE: Configuring as mouse
[ 29.092] (II) evdev: USB OPTICAL MOUSE: Adding scrollwheel support
[ 29.092] (**) evdev: USB OPTICAL MOUSE: YAxisMapping: buttons 4 and 5
[ 29.092] (**) evdev: USB OPTICAL MOUSE: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 29.092] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.0/0003:0000:0538.0001/input/input1/event1"
[ 29.092] (II) XINPUT: Adding extended input device " USB OPTICAL MOUSE" (type: MOUSE, id 9)
[ 29.092] (II) evdev: USB OPTICAL MOUSE: initialized for relative axes.
[ 29.093] (**) USB OPTICAL MOUSE: (accel) keeping acceleration scheme 1
[ 29.093] (**) USB OPTICAL MOUSE: (accel) acceleration profile 0
[ 29.093] (**) USB OPTICAL MOUSE: (accel) acceleration factor: 2.000
[ 29.093] (**) USB OPTICAL MOUSE: (accel) acceleration threshold: 4
[ 29.094] (II) config/udev: Adding input device USB OPTICAL MOUSE (/dev/input/mouse0)
[ 29.094] (II) No input driver specified, ignoring this device.
[ 29.094] (II) This device may have been added with another device file.
[ 29.094] (II) config/udev: Adding input device HDA Intel PCH Front Mic (/dev/input/event4)
[ 29.094] (II) No input driver specified, ignoring this device.
[ 29.094] (II) This device may have been added with another device file.
[ 29.095] (II) config/udev: Adding input device HDA Intel PCH Rear Mic (/dev/input/event5)
[ 29.095] (II) No input driver specified, ignoring this device.
[ 29.095] (II) This device may have been added with another device file.
[ 29.096] (II) config/udev: Adding input device HDA Intel PCH Line (/dev/input/event6)
[ 29.096] (II) No input driver specified, ignoring this device.
[ 29.096] (II) This device may have been added with another device file.
[ 29.096] (II) config/udev: Adding input device HDA Intel PCH Line Out (/dev/input/event7)
[ 29.096] (II) No input driver specified, ignoring this device.
[ 29.096] (II) This device may have been added with another device file.
[ 29.097] (II) config/udev: Adding input device HDA Intel PCH Front Headphone (/dev/input/event8)
[ 29.097] (II) No input driver specified, ignoring this device.
[ 29.097] (II) This device may have been added with another device file.
[ 29.097] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event9)
[ 29.098] (II) No input driver specified, ignoring this device.
[ 29.098] (II) This device may have been added with another device file.
[ 29.098] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[ 29.098] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 29.098] (**) AT Translated Set 2 keyboard: Applying InputClass "system-keyboard"
[ 29.099] (II) systemd-logind: got fd for /dev/input/event0 13:64 fd 16 paused 0
[ 29.099] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[ 29.099] (**) AT Translated Set 2 keyboard: always reports core events
[ 29.099] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[ 29.099] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
[ 29.099] (--) evdev: AT Translated Set 2 keyboard: Found keys
[ 29.099] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
[ 29.099] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[ 29.100] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 10)
[ 29.100] (**) Option "xkb_rules" "evdev"
[ 29.100] (**) Option "xkb_model" "pc104"
[ 29.100] (**) Option "xkb_layout" "br"
[ 29.100] (**) Option "xkb_options" "grp:alt_shift_toggle"
[ 29.101] (II) config/udev: Adding input device PC Speaker (/dev/input/event10)
[ 29.101] (II) No input driver specified, ignoring this device.
[ 29.101] (II) This device may have been added with another device file.
[ 30.903] (WW) EDID timing clock 85.50 exceeds claimed max 85MHz, fixing
[ 30.904] (II) intel(0): EDID vendor "PHL", prod id 2165
[ 30.904] (II) intel(0): Using EDID range info for horizontal sync
[ 30.904] (II) intel(0): Using EDID range info for vertical refresh
[ 30.904] (II) intel(0): Printing DDC gathered Modelines:
[ 30.904] (II) intel(0): Modeline "1366x768"x0.0 85.50 1366 1436 1579 1792 768 771 774 798 +hsync +vsync (47.7 kHz eP)
[ 30.904] (II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 30.904] (II) intel(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 30.904] (II) intel(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 30.904] (II) intel(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz e)
[ 30.904] (II) intel(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e)
[ 30.904] (II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 30.904] (II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 30.904] (II) intel(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz e)
[ 30.904] (II) intel(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e)
[ 30.904] (II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 30.904] (II) intel(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e)
[ 30.904] (II) intel(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 30.904] (II) intel(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e)
[ 30.904] (II) intel(0): Modeline "640x400"x70.0 23.35 640 656 720 800 400 401 404 417 -hsync +vsync (29.2 kHz e)
[ 30.904] (II) intel(0): Modeline "1024x768"x72.0 78.43 1024 1080 1192 1360 768 769 772 801 -hsync +vsync (57.7 kHz e)
[ 81.026] (WW) EDID timing clock 85.50 exceeds claimed max 85MHz, fixing
[ 81.026] (II) intel(0): EDID vendor "PHL", prod id 2165
[ 81.026] (II) intel(0): Using hsync ranges from config file
[ 81.026] (II) intel(0): Using vrefresh ranges from config file
[ 81.026] (II) intel(0): Printing DDC gathered Modelines:
[ 81.026] (II) intel(0): Modeline "1366x768"x0.0 85.50 1366 1436 1579 1792 768 771 774 798 +hsync +vsync (47.7 kHz eP)
[ 81.026] (II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 81.027] (II) intel(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 81.027] (II) intel(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 81.027] (II) intel(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz e)
[ 81.027] (II) intel(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e)
[ 81.027] (II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 81.027] (II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 81.027] (II) intel(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz e)
[ 81.027] (II) intel(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e)
[ 81.027] (II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 81.027] (II) intel(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e)
[ 81.027] (II) intel(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 81.027] (II) intel(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e)
[ 81.027] (II) intel(0): Modeline "640x400"x70.0 23.35 640 656 720 800 400 401 404 417 -hsync +vsync (29.2 kHz e)
[ 81.027] (II) intel(0): Modeline "1024x768"x72.0 78.43 1024 1080 1192 1360 768 769 772 801 -hsync +vsync (57.7 kHz e)
[ 2054.395] (WW) EDID timing clock 85.50 exceeds claimed max 85MHz, fixing
[ 2054.395] (II) intel(0): EDID vendor "PHL", prod id 2165
[ 2054.395] (II) intel(0): Using hsync ranges from config file
[ 2054.395] (II) intel(0): Using vrefresh ranges from config file
[ 2054.395] (II) intel(0): Printing DDC gathered Modelines:
[ 2054.395] (II) intel(0): Modeline "1366x768"x0.0 85.50 1366 1436 1579 1792 768 771 774 798 +hsync +vsync (47.7 kHz eP)
[ 2054.395] (II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 2054.395] (II) intel(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 2054.395] (II) intel(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 2054.395] (II) intel(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz e)
[ 2054.395] (II) intel(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e)
[ 2054.395] (II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 2054.395] (II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 2054.395] (II) intel(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz e)
[ 2054.395] (II) intel(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e)
[ 2054.395] (II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 2054.395] (II) intel(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e)
[ 2054.395] (II) intel(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 2054.395] (II) intel(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e)
[ 2054.395] (II) intel(0): Modeline "640x400"x70.0 23.35 640 656 720 800 400 401 404 417 -hsync +vsync (29.2 kHz e)
[ 2054.395] (II) intel(0): Modeline "1024x768"x72.0 78.43 1024 1080 1192 1360 768 769 772 801 -hsync +vsync (57.7 kHz e)
[ 3401.178] (WW) EDID timing clock 85.50 exceeds claimed max 85MHz, fixing
[ 3401.178] (II) intel(0): EDID vendor "PHL", prod id 2165
[ 3401.178] (II) intel(0): Using hsync ranges from config file
[ 3401.178] (II) intel(0): Using vrefresh ranges from config file
[ 3401.178] (II) intel(0): Printing DDC gathered Modelines:
[ 3401.178] (II) intel(0): Modeline "1366x768"x0.0 85.50 1366 1436 1579 1792 768 771 774 798 +hsync +vsync (47.7 kHz eP)
[ 3401.178] (II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 3401.178] (II) intel(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 3401.178] (II) intel(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 3401.178] (II) intel(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz e)
[ 3401.178] (II) intel(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e)
[ 3401.178] (II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 3401.178] (II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 3401.178] (II) intel(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz e)
[ 3401.178] (II) intel(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e)
[ 3401.178] (II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 3401.178] (II) intel(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e)
[ 3401.178] (II) intel(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 3401.178] (II) intel(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e)
[ 3401.178] (II) intel(0): Modeline "640x400"x70.0 23.35 640 656 720 800 400 401 404 417 -hsync +vsync (29.2 kHz e)
[ 3401.178] (II) intel(0): Modeline "1024x768"x72.0 78.43 1024 1080 1192 1360 768 769 772 801 -hsync +vsync (57.7 kHz e)
[ 8382.203] (II) config/udev: removing device USB OPTICAL MOUSE
[ 8382.204] (II) evdev: USB OPTICAL MOUSE: Close
[ 8382.204] (II) UnloadModule: "evdev"
[ 8382.204] (II) systemd-logind: releasing fd for 13:65
[ 8382.571] (II) config/udev: Adding input device USB OPTICAL MOUSE (/dev/input/mouse0)
[ 8382.571] (II) No input driver specified, ignoring this device.
[ 8382.571] (II) This device may have been added with another device file.
[ 8382.686] (II) config/udev: Adding input device USB OPTICAL MOUSE (/dev/input/event1)
[ 8382.687] (**) USB OPTICAL MOUSE: Applying InputClass "evdev pointer catchall"
[ 8382.739] (II) systemd-logind: got fd for /dev/input/event1 13:65 fd 18 paused 0
[ 8382.739] (II) Using input driver 'evdev' for ' USB OPTICAL MOUSE'
[ 8382.739] (**) USB OPTICAL MOUSE: always reports core events
[ 8382.739] (**) evdev: USB OPTICAL MOUSE: Device: "/dev/input/event1"
[ 8382.739] (--) evdev: USB OPTICAL MOUSE: Vendor 0 Product 0x538
[ 8382.740] (--) evdev: USB OPTICAL MOUSE: Found 3 mouse buttons
[ 8382.740] (--) evdev: USB OPTICAL MOUSE: Found scroll wheel(s)
[ 8382.740] (--) evdev: USB OPTICAL MOUSE: Found relative axes
[ 8382.740] (--) evdev: USB OPTICAL MOUSE: Found x and y relative axes
[ 8382.740] (II) evdev: USB OPTICAL MOUSE: Configuring as mouse
[ 8382.740] (II) evdev: USB OPTICAL MOUSE: Adding scrollwheel support
[ 8382.740] (**) evdev: USB OPTICAL MOUSE: YAxisMapping: buttons 4 and 5
[ 8382.740] (**) evdev: USB OPTICAL MOUSE: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 8382.740] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.0/0003:0000:0538.0002/input/input12/event1"
[ 8382.740] (II) XINPUT: Adding extended input device " USB OPTICAL MOUSE" (type: MOUSE, id 9)
[ 8382.740] (II) evdev: USB OPTICAL MOUSE: initialized for relative axes.
[ 8382.740] (**) USB OPTICAL MOUSE: (accel) keeping acceleration scheme 1
[ 8382.741] (**) USB OPTICAL MOUSE: (accel) acceleration profile 0
[ 8382.741] (**) USB OPTICAL MOUSE: (accel) acceleration factor: 2.000
[ 8382.741] (**) USB OPTICAL MOUSE: (accel) acceleration threshold: 4
[ 30193.014] (II) config/udev: removing device USB OPTICAL MOUSE
[ 30193.014] (II) evdev: USB OPTICAL MOUSE: Close
[ 30193.014] (II) UnloadModule: "evdev"
[ 30193.014] (II) systemd-logind: releasing fd for 13:65
[ 30193.371] (II) config/udev: Adding input device USB OPTICAL MOUSE (/dev/input/mouse0)
[ 30193.372] (II) No input driver specified, ignoring this device.
[ 30193.372] (II) This device may have been added with another device file.
[ 30193.487] (II) config/udev: Adding input device USB OPTICAL MOUSE (/dev/input/event1)
[ 30193.488] (**) USB OPTICAL MOUSE: Applying InputClass "evdev pointer catchall"
[ 30193.540] (II) systemd-logind: got fd for /dev/input/event1 13:65 fd 18 paused 0
[ 30193.541] (II) Using input driver 'evdev' for ' USB OPTICAL MOUSE'
[ 30193.541] (**) USB OPTICAL MOUSE: always reports core events
[ 30193.541] (**) evdev: USB OPTICAL MOUSE: Device: "/dev/input/event1"
[ 30193.541] (--) evdev: USB OPTICAL MOUSE: Vendor 0 Product 0x538
[ 30193.541] (--) evdev: USB OPTICAL MOUSE: Found 3 mouse buttons
[ 30193.541] (--) evdev: USB OPTICAL MOUSE: Found scroll wheel(s)
[ 30193.541] (--) evdev: USB OPTICAL MOUSE: Found relative axes
[ 30193.541] (--) evdev: USB OPTICAL MOUSE: Found x and y relative axes
[ 30193.541] (II) evdev: USB OPTICAL MOUSE: Configuring as mouse
[ 30193.541] (II) evdev: USB OPTICAL MOUSE: Adding scrollwheel support
[ 30193.541] (**) evdev: USB OPTICAL MOUSE: YAxisMapping: buttons 4 and 5
[ 30193.541] (**) evdev: USB OPTICAL MOUSE: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 30193.541] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.0/0003:0000:0538.0003/input/input13/event1"
[ 30193.541] (II) XINPUT: Adding extended input device " USB OPTICAL MOUSE" (type: MOUSE, id 9)
[ 30193.541] (II) evdev: USB OPTICAL MOUSE: initialized for relative axes.
[ 30193.542] (**) USB OPTICAL MOUSE: (accel) keeping acceleration scheme 1
[ 30193.542] (**) USB OPTICAL MOUSE: (accel) acceleration profile 0
[ 30193.542] (**) USB OPTICAL MOUSE: (accel) acceleration factor: 2.000
[ 30193.542] (**) USB OPTICAL MOUSE: (accel) acceleration threshold: 4
[ 48249.994] (WW) EDID timing clock 85.50 exceeds claimed max 85MHz, fixing
[ 48250.033] (II) intel(0): EDID vendor "PHL", prod id 2165
[ 48250.033] (II) intel(0): Using hsync ranges from config file
[ 48250.033] (II) intel(0): Using vrefresh ranges from config file
[ 48250.034] (II) intel(0): Printing DDC gathered Modelines:
[ 48250.034] (II) intel(0): Modeline "1366x768"x0.0 85.50 1366 1436 1579 1792 768 771 774 798 +hsync +vsync (47.7 kHz eP)
[ 48250.034] (II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 48250.034] (II) intel(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 48250.034] (II) intel(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 48250.034] (II) intel(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz e)
[ 48250.034] (II) intel(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e)
[ 48250.034] (II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 48250.034] (II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 48250.034] (II) intel(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz e)
[ 48250.034] (II) intel(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e)
[ 48250.034] (II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 48250.034] (II) intel(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e)
[ 48250.034] (II) intel(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 48250.034] (II) intel(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e)
[ 48250.034] (II) intel(0): Modeline "640x400"x70.0 23.35 640 656 720 800 400 401 404 417 -hsync +vsync (29.2 kHz e)
[ 48250.034] (II) intel(0): Modeline "1024x768"x72.0 78.43 1024 1080 1192 1360 768 769 772 801 -hsync +vsync (57.7 kHz e)
[ 48304.002] (WW) EDID timing clock 85.50 exceeds claimed max 85MHz, fixing
[ 48304.002] (II) intel(0): EDID vendor "PHL", prod id 2165
[ 48304.002] (II) intel(0): Using hsync ranges from config file
[ 48304.002] (II) intel(0): Using vrefresh ranges from config file
[ 48304.002] (II) intel(0): Printing DDC gathered Modelines:
[ 48304.002] (II) intel(0): Modeline "1366x768"x0.0 85.50 1366 1436 1579 1792 768 771 774 798 +hsync +vsync (47.7 kHz eP)
[ 48304.002] (II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 48304.002] (II) intel(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 48304.002] (II) intel(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 48304.002] (II) intel(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz e)
[ 48304.002] (II) intel(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e)
[ 48304.002] (II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 48304.002] (II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 48304.002] (II) intel(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz e)
[ 48304.002] (II) intel(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e)
[ 48304.002] (II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 48304.002] (II) intel(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e)
[ 48304.002] (II) intel(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 48304.002] (II) intel(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e)
[ 48304.002] (II) intel(0): Modeline "640x400"x70.0 23.35 640 656 720 800 400 401 404 417 -hsync +vsync (29.2 kHz e)
[ 48304.002] (II) intel(0): Modeline "1024x768"x72.0 78.43 1024 1080 1192 1360 768 769 772 801 -hsync +vsync (57.7 kHz e)
[ 48868.910] (WW) EDID timing clock 85.50 exceeds claimed max 85MHz, fixing
[ 48868.911] (II) intel(0): EDID vendor "PHL", prod id 2165
[ 48868.911] (II) intel(0): Using hsync ranges from config file
[ 48868.911] (II) intel(0): Using vrefresh ranges from config file
[ 48868.911] (II) intel(0): Printing DDC gathered Modelines:
[ 48868.911] (II) intel(0): Modeline "1366x768"x0.0 85.50 1366 1436 1579 1792 768 771 774 798 +hsync +vsync (47.7 kHz eP)
[ 48868.911] (II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 48868.911] (II) intel(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 48868.911] (II) intel(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 48868.911] (II) intel(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz e)
[ 48868.911] (II) intel(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e)
[ 48868.923] (II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 48868.923] (II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 48868.923] (II) intel(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz e)
[ 48868.923] (II) intel(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e)
[ 48868.923] (II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 48868.923] (II) intel(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e)
[ 48868.923] (II) intel(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 48868.923] (II) intel(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e)
[ 48868.923] (II) intel(0): Modeline "640x400"x70.0 23.35 640 656 720 800 400 401 404 417 -hsync +vsync (29.2 kHz e)
[ 48868.923] (II) intel(0): Modeline "1024x768"x72.0 78.43 1024 1080 1192 1360 768 769 772 801 -hsync +vsync (57.7 kHz e)
[ 49957.596] (WW) EDID timing clock 85.50 exceeds claimed max 85MHz, fixing
[ 49957.596] (II) intel(0): EDID vendor "PHL", prod id 2165
[ 49957.596] (II) intel(0): Using hsync ranges from config file
[ 49957.596] (II) intel(0): Using vrefresh ranges from config file
[ 49957.596] (II) intel(0): Printing DDC gathered Modelines:
[ 49957.596] (II) intel(0): Modeline "1366x768"x0.0 85.50 1366 1436 1579 1792 768 771 774 798 +hsync +vsync (47.7 kHz eP)
[ 49957.596] (II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 49957.597] (II) intel(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 49957.597] (II) intel(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 49957.597] (II) intel(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz e)
[ 49957.597] (II) intel(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e)
[ 49957.597] (II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 49957.597] (II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 49957.597] (II) intel(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz e)
[ 49957.597] (II) intel(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e)
[ 49957.597] (II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 49957.597] (II) intel(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e)
[ 49957.597] (II) intel(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 49957.597] (II) intel(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e)
[ 49957.597] (II) intel(0): Modeline "640x400"x70.0 23.35 640 656 720 800 400 401 404 417 -hsync +vsync (29.2 kHz e)
[ 49957.597] (II) intel(0): Modeline "1024x768"x72.0 78.43 1024 1080 1192 1360 768 769 772 801 -hsync +vsync (57.7 kHz e)
[ 52399.262] (WW) EDID timing clock 85.50 exceeds claimed max 85MHz, fixing
[ 52399.262] (II) intel(0): EDID vendor "PHL", prod id 2165
[ 52399.262] (II) intel(0): Using hsync ranges from config file
[ 52399.262] (II) intel(0): Using vrefresh ranges from config file
[ 52399.262] (II) intel(0): Printing DDC gathered Modelines:
[ 52399.262] (II) intel(0): Modeline "1366x768"x0.0 85.50 1366 1436 1579 1792 768 771 774 798 +hsync +vsync (47.7 kHz eP)
[ 52399.262] (II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 52399.262] (II) intel(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 52399.276] (II) intel(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 52399.276] (II) intel(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz e)
[ 52399.277] (II) intel(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e)
[ 52399.277] (II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 52399.277] (II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 52399.277] (II) intel(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz e)
[ 52399.277] (II) intel(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e)
[ 52399.277] (II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 52399.277] (II) intel(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e)
[ 52399.277] (II) intel(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 52399.277] (II) intel(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e)
[ 52399.277] (II) intel(0): Modeline "640x400"x70.0 23.35 640 656 720 800 400 401 404 417 -hsync +vsync (29.2 kHz e)
[ 52399.277] (II) intel(0): Modeline "1024x768"x72.0 78.43 1024 1080 1192 1360 768 769 772 801 -hsync +vsync (57.7 kHz e)
[ 54776.725] (WW) EDID timing clock 85.50 exceeds claimed max 85MHz, fixing
[ 54776.726] (II) intel(0): EDID vendor "PHL", prod id 2165
[ 54776.726] (II) intel(0): Using hsync ranges from config file
[ 54776.726] (II) intel(0): Using vrefresh ranges from config file
[ 54776.726] (II) intel(0): Printing DDC gathered Modelines:
[ 54776.726] (II) intel(0): Modeline "1366x768"x0.0 85.50 1366 1436 1579 1792 768 771 774 798 +hsync +vsync (47.7 kHz eP)
[ 54776.726] (II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 54776.727] (II) intel(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 54776.727] (II) intel(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 54776.727] (II) intel(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz e)
[ 54776.727] (II) intel(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e)
[ 54776.727] (II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 54776.727] (II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 54776.727] (II) intel(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz e)
[ 54776.727] (II) intel(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e)
[ 54776.727] (II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 54776.727] (II) intel(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e)
[ 54776.727] (II) intel(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 54776.727] (II) intel(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e)
[ 54776.727] (II) intel(0): Modeline "640x400"x70.0 23.35 640 656 720 800 400 401 404 417 -hsync +vsync (29.2 kHz e)
[ 54776.727] (II) intel(0): Modeline "1024x768"x72.0 78.43 1024 1080 1192 1360 768 769 772 801 -hsync +vsync (57.7 kHz e)
[ 68436.798] (II) AIGLX: Suspending AIGLX clients for VT switch
[ 68436.884] (II) systemd-logind: got pause for 13:65
[ 68436.894] (II) systemd-logind: got pause for 226:0
[ 68436.894] (II) systemd-logind: got pause for 13:67
[ 68436.894] (II) systemd-logind: got pause for 13:64
[ 68436.895] (II) systemd-logind: got pause for 13:75
[ 68436.895] (II) systemd-logind: got pause for 13:66
[ 68445.774] (II) systemd-logind: got resume for 13:65
[ 68445.774] (II) systemd-logind: got resume for 226:0
[ 68445.775] (II) AIGLX: Resuming AIGLX clients after VT switch
[ 68445.812] (WW) EDID timing clock 85.50 exceeds claimed max 85MHz, fixing
[ 68445.812] (II) intel(0): EDID vendor "PHL", prod id 2165
[ 68445.812] (II) intel(0): Using hsync ranges from config file
[ 68445.812] (II) intel(0): Using vrefresh ranges from config file
[ 68445.812] (II) intel(0): Printing DDC gathered Modelines:
[ 68445.812] (II) intel(0): Modeline "1366x768"x0.0 85.50 1366 1436 1579 1792 768 771 774 798 +hsync +vsync (47.7 kHz eP)
[ 68445.812] (II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 68445.812] (II) intel(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 68445.812] (II) intel(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 68445.812] (II) intel(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz e)
[ 68445.812] (II) intel(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e)
[ 68445.812] (II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 68445.812] (II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 68445.812] (II) intel(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz e)
[ 68445.812] (II) intel(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e)
[ 68445.812] (II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 68445.812] (II) intel(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e)
[ 68445.812] (II) intel(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 68445.812] (II) intel(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e)
[ 68445.812] (II) intel(0): Modeline "640x400"x70.0 23.35 640 656 720 800 400 401 404 417 -hsync +vsync (29.2 kHz e)
[ 68445.812] (II) intel(0): Modeline "1024x768"x72.0 78.43 1024 1080 1192 1360 768 769 772 801 -hsync +vsync (57.7 kHz e)
[ 68445.821] (II) systemd-logind: got resume for 13:67
[ 68445.821] (II) systemd-logind: got resume for 13:64
[ 68445.821] (II) systemd-logind: got resume for 13:75
[ 68445.842] (II) systemd-logind: got resume for 13:66
[ 69731.770] (II) AIGLX: Suspending AIGLX clients for VT switch
[ 69731.801] (II) systemd-logind: got pause for 13:65
[ 69731.802] (II) systemd-logind: got pause for 226:0
[ 69731.802] (II) systemd-logind: got pause for 13:67
[ 69731.802] (II) systemd-logind: got pause for 13:64
[ 69731.803] (II) systemd-logind: got pause for 13:75
[ 69731.803] (II) systemd-logind: got pause for 13:66
[ 69743.577] (II) evdev: USB OPTICAL MOUSE: Close
[ 69743.577] (II) UnloadModule: "evdev"
[ 69743.577] (II) systemd-logind: releasing fd for 13:65
[ 69743.597] (II) evdev: AT Translated Set 2 keyboard: Close
[ 69743.597] (II) UnloadModule: "evdev"
[ 69743.597] (II) systemd-logind: releasing fd for 13:64
[ 69743.610] (II) evdev: Power Button: Close
[ 69743.610] (II) UnloadModule: "evdev"
[ 69743.610] (II) systemd-logind: releasing fd for 13:66
[ 69743.623] (II) evdev: Video Bus: Close
[ 69743.623] (II) UnloadModule: "evdev"
[ 69743.623] (II) systemd-logind: releasing fd for 13:75
[ 69743.639] (II) evdev: Power Button: Close
[ 69743.640] (II) UnloadModule: "evdev"
[ 69743.640] (II) systemd-logind: releasing fd for 13:67
[ 69746.970] (EE)
Fatal server error:
[ 69746.970] (EE) xf86OpenConsole: VT_ACTIVATE failed: Input/output error
[ 69746.970] (EE)
[ 69746.970] (EE)
Please consult the The X.Org Foundation support
at http://wiki.x.org
for help.
[ 69746.970] (EE) Please also check the log file at "/home/victor/.local/share/xorg/Xorg.0.log" for additional information.
[ 69746.970] (EE)
[ 69746.970] (WW) xf86CloseConsole: KDSETMODE failed: Input/output error
[ 69746.970] (WW) xf86CloseConsole: VT_GETMODE failed: Input/output error
[ 69746.970] (EE)
FatalError re-entered, aborting
[ 69746.970] (EE) xf86CloseConsole: VT_ACTIVATE failed: Input/output error
[ 69746.970] (EE) Offline
#8 2015-08-22 14:23:38
- hotvic
- Member
- Registered: 2013-02-11
- Posts: 109
Re: recently high X CPU usage
I've disabled IPS (i915.enable_ips=0) and switched back to sna and until now its fine, 0.5~6% and no graphic corruption until now.
but this is a workaround, the usage with uxa isn't normal and should be fixed, I think!
Offline