You are not logged in.
- Topics: Active | Unanswered
#1 2016-02-13 22:49:51
- chmercesmoreira
- Member
- From: Rio de Janeiro/Brazil
- Registered: 2016-02-13
- Posts: 13
[SOLVED] iwl4965 can't connect to 2.4Ghz only 5.0Ghz
Hello, I'm having a weird problem, I'm being unable to establish a connection to my home WiFi connection when I set up it to 2.4Ghz, but when I set up to 5.0Ghz I am able to connect. Sorry my poor English.
Here is some output:
$ lspci | grep -i net
01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 06)
02:00.0 Network controller: Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection (rev 61)$ iwconfig
wlp2s0 IEEE 802.11abgn ESSID:"netvirtuabl25ap302"
Mode:Managed Frequency:5.2 GHz Access Point: 6C:B5:6B:51:AC:98
Bit Rate=150 Mb/s Tx-Power=15 dBm
Retry short limit:7 RTS thr:off Fragment thr:off
Power Management:off
Link Quality=60/70 Signal level=-50 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:20 Invalid misc:272 Missed beacon:0
lo no wireless extensions.
enp1s0 no wireless extensions.$ iwlist wlp2s0 freq
wlp2s0 24 channels in total; available frequencies :
Channel 01 : 2.412 GHz
Channel 02 : 2.417 GHz
Channel 03 : 2.422 GHz
Channel 04 : 2.427 GHz
Channel 05 : 2.432 GHz
Channel 06 : 2.437 GHz
Channel 07 : 2.442 GHz
Channel 08 : 2.447 GHz
Channel 09 : 2.452 GHz
Channel 10 : 2.457 GHz
Channel 11 : 2.462 GHz
Channel 36 : 5.18 GHz
Channel 40 : 5.2 GHz
Channel 44 : 5.22 GHz
Channel 48 : 5.24 GHz
Channel 52 : 5.26 GHz
Channel 56 : 5.28 GHz
Channel 60 : 5.3 GHz
Channel 64 : 5.32 GHz
Channel 149 : 5.745 GHz
Channel 153 : 5.765 GHz
Channel 157 : 5.785 GHz
Channel 161 : 5.805 GHz
Channel 165 : 5.825 GHz
Current Frequency:5.2 GHz (Channel 40)$ iw phy
Wiphy phy0
max # scan SSIDs: 20
max scan IEs length: 127 bytes
max # sched scan SSIDs: 0
max # match sets: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports RSN-IBSS.
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP (00-0f-ac:4)
* 00-0f-ac:10
* GCMP (00-0f-ac:8)
* 00-0f-ac:9
Available Antennas: TX 0 RX 0
Supported interface modes:
* IBSS
* managed
* monitor
Band 1:
Capabilities: 0x20
HT20
Static SM Power Save
RX HT20 SGI
No RX STBC
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 4 usec (0x05)
HT Max RX data rate: 216 Mbps
HT RX MCS rate indexes supported: 0-23
TX unequal modulation not supported
HT TX Max spatial streams: 2
HT TX MCS rate indexes supported may differ
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 2412 MHz [1] (14.0 dBm)
* 2417 MHz [2] (14.0 dBm)
* 2422 MHz [3] (14.0 dBm)
* 2427 MHz [4] (14.0 dBm)
* 2432 MHz [5] (14.0 dBm)
* 2437 MHz [6] (14.0 dBm)
* 2442 MHz [7] (14.0 dBm)
* 2447 MHz [8] (14.0 dBm)
* 2452 MHz [9] (14.0 dBm)
* 2457 MHz [10] (14.0 dBm)
* 2462 MHz [11] (14.0 dBm)
Band 2:
Capabilities: 0x62
HT20/HT40
Static SM Power Save
RX HT20 SGI
RX HT40 SGI
No RX STBC
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 4 usec (0x05)
HT Max RX data rate: 450 Mbps
HT RX MCS rate indexes supported: 0-23, 32
TX unequal modulation not supported
HT TX Max spatial streams: 2
HT TX MCS rate indexes supported may differ
Bitrates (non-HT):
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 5180 MHz [36] (15.0 dBm) (no IR)
* 5200 MHz [40] (15.0 dBm) (no IR)
* 5220 MHz [44] (15.0 dBm) (no IR)
* 5240 MHz [48] (15.0 dBm) (no IR)
* 5260 MHz [52] (15.0 dBm) (no IR, radar detection)
DFS state: usable (for 1434342 sec)
DFS CAC time: 0 ms
* 5280 MHz [56] (15.0 dBm) (no IR, radar detection)
DFS state: usable (for 1434342 sec)
DFS CAC time: 0 ms
* 5300 MHz [60] (15.0 dBm) (no IR, radar detection)
DFS state: usable (for 1434342 sec)
DFS CAC time: 0 ms
* 5320 MHz [64] (15.0 dBm) (no IR, radar detection)
DFS state: usable (for 1434342 sec)
DFS CAC time: 0 ms
* 5745 MHz [149] (16.0 dBm) (no IR)
* 5765 MHz [153] (16.0 dBm) (no IR)
* 5785 MHz [157] (16.0 dBm) (no IR)
* 5805 MHz [161] (16.0 dBm) (no IR)
* 5825 MHz [165] (16.0 dBm) (no IR)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* new_mpath
* set_mesh_config
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* join_mesh
* set_tx_bitrate_mask
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* set_wds_peer
* probe_client
* set_noack_map
* register_beacons
* start_p2p_device
* set_mcast_rate
* set_qos_map
* connect
* disconnect
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xd0
software interface modes (can always be added):
* monitor
interface combinations are not supported
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
Device supports SAE with AUTHENTICATE command
Device supports scan flush.
Device supports per-vif TX power setting
Driver supports a userspace MPM
Device supports static SMPS
Device supports dynamic SMPS
Device supports configuring vdev MAC-addr on create.$ less /proc/modules | grep -i iwl4965
iwl4965 106496 0 - Live 0xffffffffa0847000
iwlegacy 57344 1 iwl4965, Live 0xffffffffa03dc000
mac80211 667648 2 iwl4965,iwlegacy, Live 0xffffffffa0773000
cfg80211 483328 3 iwl4965,iwlegacy,mac80211, Live 0xffffffffa0420000$ sudo systool -m iwl4965 -av
Module = "iwl4965"
Attributes:
coresize = "106496"
initsize = "0"
initstate = "live"
refcnt = "0"
srcversion = "70E20729D43304144506C0B"
taint = ""
uevent = <store method only>
version = "in-tree:"
Parameters:
11n_disable = "0"
amsdu_size_8K = "0"
fw_restart = "1"
queues_num = "0"
swcrypto = "0"
Sections:
.data = "0xffffffffa085e000"
.data.unlikely = "0xffffffffa085e614"
.exit.text = "0xffffffffa085971e"
.gnu.linkonce.this_module= "0xffffffffa085e620"
.init.text = "0xffffffffa0862000"
.note.gnu.build-id = "0xffffffffa085a000"
.parainstructions = "0xffffffffa085d1a0"
.rodata = "0xffffffffa085a040"
.rodata.str1.1 = "0xffffffffa085c23b"
.rodata.str1.8 = "0xffffffffa085af40"
.smp_locks = "0xffffffffa085cbcc"
.strtab = "0xffffffffa0865e68"
.symtab = "0xffffffffa0863000"
.text = "0xffffffffa0847000"
.text.unlikely = "0xffffffffa08591f0"
__bug_table = "0xffffffffa085d158"
__mcount_loc = "0xffffffffa085cc88"
__param = "0xffffffffa085d260"$ sudo systool -m iwlegacy -av
Module = "iwlegacy"
Attributes:
coresize = "57344"
initsize = "0"
initstate = "live"
refcnt = "1"
srcversion = "FEF91804A7E8D3E15969733"
taint = ""
uevent = <store method only>
version = "in-tree:"
Parameters:
bt_coex_active = "Y"
led_mode = "0"
Sections:
.bss = "0xffffffffa03e7288"
.data = "0xffffffffa03e7000"
.data.unlikely = "0xffffffffa03e7001"
.gnu.linkonce.this_module= "0xffffffffa03e7020"
.note.gnu.build-id = "0xffffffffa03e4000"
.parainstructions = "0xffffffffa03e5f00"
.rodata = "0xffffffffa03e4a20"
.rodata.str1.1 = "0xffffffffa03e5239"
.rodata.str1.8 = "0xffffffffa03e57e0"
.smp_locks = "0xffffffffa03e5760"
.strtab = "0xffffffffa0418050"
.symtab = "0xffffffffa0414000"
.text = "0xffffffffa03dc000"
__bug_table = "0xffffffffa03e5f2c"
__kcrctab = "0xffffffffa03e46d0"
__kcrctab_gpl = "0xffffffffa03e49f8"
__ksymtab_gpl = "0xffffffffa03e4680"
__ksymtab_strings = "0xffffffffa03e5fc8"
__ksymtab = "0xffffffffa03e4030"
__mcount_loc = "0xffffffffa03e67a0"
__param = "0xffffffffa03e6760"$ sudo systool -m mac80211 -av
Module = "mac80211"
Attributes:
coresize = "667648"
initsize = "0"
initstate = "live"
refcnt = "2"
taint = ""
uevent = <store method only>
Parameters:
beacon_loss_count = "7"
ieee80211_default_rc_algo= "minstrel_ht"
max_nullfunc_tries = "2"
max_probe_tries = "5"
probe_wait_ms = "500"
Sections:
.altinstr_replacement= "0xffffffffa07e44b3"
.altinstructions = "0xffffffffa07f68c0"
.bss = "0xffffffffa08054c8"
.data = "0xffffffffa07f8000"
.data..read_mostly = "0xffffffffa0805200"
.data.unlikely = "0xffffffffa08015d0"
.exit.text = "0xffffffffa07e4494"
.gnu.linkonce.this_module= "0xffffffffa0805260"
.init.text = "0xffffffffa0817000"
.note.gnu.build-id = "0xffffffffa07e5000"
.ref.data = "0xffffffffa08019c0"
.rodata = "0xffffffffa07e5a00"
.rodata.str1.1 = "0xffffffffa07f1452"
.rodata.str1.8 = "0xffffffffa07ee500"
.smp_locks = "0xffffffffa07f6498"
.strtab = "0xffffffffa082feb8"
.symtab = "0xffffffffa081d000"
.text = "0xffffffffa0773000"
.text.unlikely = "0xffffffffa07e3750"
__bug_table = "0xffffffffa07f6788"
__jump_table = "0xffffffffa07ff560"
__kcrctab = "0xffffffffa07e56b0"
__kcrctab_gpl = "0xffffffffa07e5958"
__ksymtab_gpl = "0xffffffffa07e5580"
__ksymtab_strings = "0xffffffffa07f3a12"
__ksymtab = "0xffffffffa07e5030"
__mcount_loc = "0xffffffffa07f44a0"
__param = "0xffffffffa07f6908"
__tracepoints_ptrs = "0xffffffffa07f69a8"
__tracepoints_strings= "0xffffffffa07f6d20"
__tracepoints = "0xffffffffa08035e0"
__verbose = "0xffffffffa0805198"
_ftrace_events = "0xffffffffa0801640"$ sudo systool -m cfg80211 -av
Module = "cfg80211"
Attributes:
coresize = "483328"
initsize = "0"
initstate = "live"
refcnt = "3"
taint = ""
uevent = <store method only>
Parameters:
cfg80211_disable_40mhz_24ghz= "N"
ieee80211_regdom = "00"
Sections:
.altinstr_replacement= "0xffffffffa046ee0e"
.altinstructions = "0xffffffffa0476570"
.bss = "0xffffffffa0489520"
.data = "0xffffffffa0478000"
.data.unlikely = "0xffffffffa0484148"
.exit.text = "0xffffffffa046edc9"
.gnu.linkonce.this_module= "0xffffffffa04892a0"
.init.text = "0xffffffffa052d000"
.note.gnu.build-id = "0xffffffffa046f000"
.ref.data = "0xffffffffa04845c0"
.rodata = "0xffffffffa046fb20"
.rodata.str1.1 = "0xffffffffa0471ad8"
.rodata.str1.8 = "0xffffffffa0473090"
.smp_locks = "0xffffffffa0474a78"
.strtab = "0xffffffffa0545410"
.symtab = "0xffffffffa0535000"
.text = "0xffffffffa0420000"
.text.unlikely = "0xffffffffa046ea88"
__bug_table = "0xffffffffa0472b80"
__jump_table = "0xffffffffa04825d0"
__kcrctab = "0xffffffffa046f770"
__kcrctab_gpl = "0xffffffffa046faa8"
__ksymtab_gpl = "0xffffffffa046f6a0"
__ksymtab_strings = "0xffffffffa0474ab8"
__ksymtab = "0xffffffffa046f030"
__mcount_loc = "0xffffffffa0475618"
__param = "0xffffffffa04755d8"
__tracepoints_ptrs = "0xffffffffa0476580"
__tracepoints_strings= "0xffffffffa0476a00"
__tracepoints = "0xffffffffa0486f60"
_ftrace_events = "0xffffffffa0484158"And finally, here is the log I'm getting when I set the 802.11 Band to 2.4Ghz from dmesg:
$ dmesg
[ 3653.254316] cfg80211: Calling CRDA to update world regulatory domain
[ 3653.259035] cfg80211: World regulatory domain updated:
[ 3653.259041] cfg80211: DFS Master region: unset
[ 3653.259044] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 3653.259048] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 3653.259052] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 3653.259055] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 3653.259058] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 3653.259062] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 3653.259065] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 3653.259068] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 3653.259071] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 3655.226825] wlp2s0: authenticate with 6c:b5:6b:51:ac:98
[ 3655.236010] wlp2s0: direct probe to 6c:b5:6b:51:ac:98 (try 1/3)
[ 3655.437586] wlp2s0: direct probe to 6c:b5:6b:51:ac:98 (try 2/3)
[ 3655.640836] wlp2s0: direct probe to 6c:b5:6b:51:ac:98 (try 3/3)
[ 3655.844099] wlp2s0: authentication with 6c:b5:6b:51:ac:98 timed out
[ 3657.333611] iwl4965 0000:02:00.0: Queue 0 stuck for 2500 ms.
[ 3657.333621] iwl4965 0000:02:00.0: On demand firmware reload
[ 3657.333804] ieee80211 phy0: Hardware restart was requested
[ 3664.413803] wlp2s0: authenticate with 6c:b5:6b:51:ac:98
[ 3664.413943] wlp2s0: direct probe to 6c:b5:6b:51:ac:98 (try 1/3)
[ 3664.614529] wlp2s0: direct probe to 6c:b5:6b:51:ac:98 (try 2/3)
[ 3664.817835] wlp2s0: direct probe to 6c:b5:6b:51:ac:98 (try 3/3)
[ 3665.021086] wlp2s0: authentication with 6c:b5:6b:51:ac:98 timed out
[ 3666.550543] iwl4965 0000:02:00.0: Queue 0 stuck for 2500 ms.
[ 3666.550549] iwl4965 0000:02:00.0: On demand firmware reload
[ 3666.550707] ieee80211 phy0: Hardware restart was requested
[ 3666.823052] wlp2s0: authenticate with 6c:b5:6b:51:ac:98
[ 3666.824695] wlp2s0: direct probe to 6c:b5:6b:51:ac:98 (try 1/3)
[ 3667.027081] wlp2s0: direct probe to 6c:b5:6b:51:ac:98 (try 2/3)
[ 3667.230347] wlp2s0: direct probe to 6c:b5:6b:51:ac:98 (try 3/3)
[ 3667.273646] iwl4965 0000:02:00.0: Queue 0 stuck for 3223 ms.
[ 3667.433658] wlp2s0: authentication with 6c:b5:6b:51:ac:98 timed out
[ 3667.773488] iwl4965 0000:02:00.0: Queue 0 stuck for 3723 ms.
[ 3668.273323] iwl4965 0000:02:00.0: Queue 0 stuck for 4223 ms.
[ 3668.773157] iwl4965 0000:02:00.0: Queue 0 stuck for 4723 ms.
[ 3668.844174] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[ 3669.272993] iwl4965 0000:02:00.0: Queue 0 stuck for 5223 ms.
[ 3669.772838] iwl4965 0000:02:00.0: Queue 0 stuck for 5723 ms.
[ 3670.272672] iwl4965 0000:02:00.0: Queue 0 stuck for 6223 ms.
[ 3670.765693] wlp2s0: authenticate with 6c:b5:6b:51:ac:98
[ 3670.765925] wlp2s0: direct probe to 6c:b5:6b:51:ac:98 (try 1/3)
[ 3670.772490] iwl4965 0000:02:00.0: Queue 0 stuck for 6723 ms.
[ 3670.969116] wlp2s0: direct probe to 6c:b5:6b:51:ac:98 (try 2/3)
[ 3671.172394] wlp2s0: direct probe to 6c:b5:6b:51:ac:98 (try 3/3)
[ 3671.272362] iwl4965 0000:02:00.0: Queue 0 stuck for 7223 ms.
[ 3671.375662] wlp2s0: authentication with 6c:b5:6b:51:ac:98 timed out
[ 3671.772170] iwl4965 0000:02:00.0: Queue 0 stuck for 7723 ms.
[ 3671.772199] iwl4965 0000:02:00.0: On demand firmware reload
[ 3671.772433] ieee80211 phy0: Hardware restart was requested
[ 3683.322117] wlp2s0: authenticate with 6c:b5:6b:51:ac:98
[ 3683.322319] wlp2s0: direct probe to 6c:b5:6b:51:ac:98 (try 1/3)
[ 3683.524978] wlp2s0: direct probe to 6c:b5:6b:51:ac:98 (try 2/3)
[ 3683.728228] wlp2s0: direct probe to 6c:b5:6b:51:ac:98 (try 3/3)
[ 3683.931522] wlp2s0: authentication with 6c:b5:6b:51:ac:98 timed out
[ 3685.481006] iwl4965 0000:02:00.0: Queue 0 stuck for 2500 ms.
[ 3685.481030] iwl4965 0000:02:00.0: On demand firmware reload
[ 3685.481238] ieee80211 phy0: Hardware restart was requested
[ 3693.810351] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[ 3697.741240] wlp2s0: authenticate with 6c:b5:6b:51:ac:98
[ 3697.741416] wlp2s0: direct probe to 6c:b5:6b:51:ac:98 (try 1/3)
[ 3697.943575] wlp2s0: direct probe to 6c:b5:6b:51:ac:98 (try 2/3)
[ 3698.146867] wlp2s0: direct probe to 6c:b5:6b:51:ac:98 (try 3/3)
[ 3698.350106] wlp2s0: authentication with 6c:b5:6b:51:ac:98 timed out
[ 3700.199506] iwl4965 0000:02:00.0: Queue 0 stuck for 2500 ms.
[ 3700.199533] iwl4965 0000:02:00.0: On demand firmware reload
[ 3700.199760] ieee80211 phy0: Hardware restart was requested
[ 3717.177173] wlp2s0: authenticate with 6c:b5:6b:51:ac:98
[ 3717.177399] wlp2s0: direct probe to 6c:b5:6b:51:ac:98 (try 1/3)
[ 3717.380505] wlp2s0: direct probe to 6c:b5:6b:51:ac:98 (try 2/3)
[ 3717.583779] wlp2s0: direct probe to 6c:b5:6b:51:ac:98 (try 3/3)
[ 3717.787042] wlp2s0: authentication with 6c:b5:6b:51:ac:98 timed out
[ 3718.802065] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[ 3719.406488] iwl4965 0000:02:00.0: Queue 0 stuck for 2500 ms.
[ 3719.406517] iwl4965 0000:02:00.0: On demand firmware reload
[ 3719.406804] ieee80211 phy0: Hardware restart was requested
[ 3719.668042] wlp2s0: authenticate with 6c:b5:6b:51:ac:98
[ 3719.668208] wlp2s0: direct probe to 6c:b5:6b:51:ac:98 (try 1/3)
[ 3719.869683] wlp2s0: direct probe to 6c:b5:6b:51:ac:98 (try 2/3)
[ 3720.072950] wlp2s0: direct probe to 6c:b5:6b:51:ac:98 (try 3/3)
[ 3720.119598] iwl4965 0000:02:00.0: Queue 0 stuck for 3213 ms.
[ 3720.276208] wlp2s0: authentication with 6c:b5:6b:51:ac:98 timed out
[ 3720.619432] iwl4965 0000:02:00.0: Queue 0 stuck for 3713 ms.
[ 3721.119290] iwl4965 0000:02:00.0: Queue 0 stuck for 4213 ms.
[ 3721.619093] iwl4965 0000:02:00.0: Queue 0 stuck for 4713 ms.
[ 3722.118930] iwl4965 0000:02:00.0: Queue 0 stuck for 5213 ms.
[ 3722.618767] iwl4965 0000:02:00.0: Queue 0 stuck for 5713 ms.
[ 3723.118600] iwl4965 0000:02:00.0: Queue 0 stuck for 6213 ms.
[ 3723.618466] iwl4965 0000:02:00.0: Queue 0 stuck for 6713 ms.
[ 3724.118288] iwl4965 0000:02:00.0: Queue 0 stuck for 7213 ms.
[ 3724.618137] iwl4965 0000:02:00.0: Queue 0 stuck for 7713 ms.
[ 3724.618149] iwl4965 0000:02:00.0: On demand firmware reload
[ 3724.618330] ieee80211 phy0: Hardware restart was requested
[ 3739.098684] wlp2s0: authenticate with 6c:b5:6b:51:ac:98
[ 3739.107851] wlp2s0: direct probe to 6c:b5:6b:51:ac:98 (try 1/3)
[ 3739.310012] wlp2s0: direct probe to 6c:b5:6b:51:ac:98 (try 2/3)
[ 3739.513224] wlp2s0: send auth to 6c:b5:6b:51:ac:98 (try 3/3)
[ 3739.570517] wlp2s0: authentication with 6c:b5:6b:51:ac:98 timed out
[ 3743.793232] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not readyAnd for information, here is what I get in the 5.0Ghz case (successfully connected):
$ dmesg
[ 3857.743145] wlp2s0: authenticate with 6c:b5:6b:51:ac:98
[ 3857.752481] wlp2s0: send auth to 6c:b5:6b:51:ac:98 (try 1/3)
[ 3857.754612] wlp2s0: send auth to 6c:b5:6b:51:ac:98 (try 2/3)
[ 3857.848689] wlp2s0: send auth to 6c:b5:6b:51:ac:98 (try 3/3)
[ 3857.849525] wlp2s0: authenticated
[ 3857.851084] wlp2s0: associate with 6c:b5:6b:51:ac:98 (try 1/3)
[ 3857.917444] wlp2s0: associate with 6c:b5:6b:51:ac:98 (try 2/3)
[ 3857.918451] wlp2s0: RX AssocResp from 6c:b5:6b:51:ac:98 (capab=0x11 status=0 aid=2)
[ 3857.938702] wlp2s0: associated
[ 3857.938775] IPv6: ADDRCONF(NETDEV_CHANGE): wlp2s0: link becomes readyLast edited by chmercesmoreira (2016-02-28 00:02:07)
Knowledge is Irresistible
Offline
#2 2016-02-28 00:01:28
- chmercesmoreira
- Member
- From: Rio de Janeiro/Brazil
- Registered: 2016-02-13
- Posts: 13
Re: [SOLVED] iwl4965 can't connect to 2.4Ghz only 5.0Ghz
Problem solved following what varunendra said here: http://ubuntuforums.org/archive/index.p … 73990.html
After that I found out what was happening here:
http://superuser.com/questions/924559/w … y-fix-work
It's was basically an interference with Bluetooth.
Last edited by chmercesmoreira (2016-02-28 00:02:51)
Knowledge is Irresistible
Offline