You are not logged in.
Hello everyone I recently purchased an ergo touchpad so that I could use along a Kinesis keyboard. Problem is that although the device is recognized when plugged in, Im unable to get any functionality out of it. I plugged it onto a windows machine and it worked there so I ruled out that the product came defective out of box. I also tried connecting it to the latest ubuntu and manjaro distros but get the same messages (will post below). Ive also tried plugging it into the other usb ports, as well as it being the only usb device connected on boot with no luck.
My Machine Model: 4236JH6 ThinkPad T420
My current kernel version: 4.8.13-1-ARCH
This is my dmesg right after boot without the touchpad being plugged in.
https://ptpb.pw/t35n
After I connect the device with no Xsession running
[ 130.571444] usb 2-1.1: new full-speed USB device number 3 using ehci-pci
[ 130.674087] input: Cirque Corporation 9925 AG Touchpad as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2
-1.1/2-1.1:1.0/0003:0488:0280.0005/input/input22
[ 130.674942] hid-generic 0003:0488:0280.0005: input,hidraw4: USB HID v1.11 Mouse [Cirque Corporation 9
925 AG Touchpad] on usb-0000:00:1d.0-1.1/input0but after I start a session with startx
[ 180.615461] usb 2-1.1: reset full-speed USB device number 3 using ehci-pci
[ 181.862072] usb 2-1.1: reset full-speed USB device number 3 using ehci-pci
[ 183.108651] usb 2-1.1: reset full-speed USB device number 3 using ehci-pci
[ 184.355347] usb 2-1.1: reset full-speed USB device number 3 using ehci-pci
[ 185.595201] usb 2-1.1: reset full-speed USB device number 3 using ehci-pci
[ 186.841823] usb 2-1.1: reset full-speed USB device number 3 using ehci-pci
[ 188.085104] usb 2-1.1: reset full-speed USB device number 3 using ehci-pci
[ 189.335018] usb 2-1.1: reset full-speed USB device number 3 using ehci-pci
[ 190.598355] usb 2-1.1: reset full-speed USB device number 3 using ehci-pci
[ 191.854932] usb 2-1.1: reset full-speed USB device number 3 using ehci-pci
[ 193.094900] usb 2-1.1: reset full-speed USB device number 3 using ehci-pci
[ 194.338087] usb 2-1.1: reset full-speed USB device number 3 using ehci-pci
[ 195.584783] usb 2-1.1: reset full-speed USB device number 3 using ehci-pci
[ 196.828035] usb 2-1.1: reset full-speed USB device number 3 using ehci-pciit spams that message on dmesg over and over until I disconnect my device
xinput recognizes the device being plugged in and here are its props listed
Device 'Cirque Corporation 9925 AG Touchpad':
Device Enabled (138): 1
Coordinate Transformation Matrix (140): 1.000000, 0.000000, 0.000000, 0.000000, 1.000000, 0.000000, 0.000000, 0.000000, 1.000000
libinput Accel Speed (274): 0.000000
libinput Accel Speed Default (275): 0.000000
libinput Accel Profiles Available (276): 1, 1
libinput Accel Profile Enabled (277): 1, 0
libinput Accel Profile Enabled Default (278): 1, 0
libinput Natural Scrolling Enabled (279): 0
libinput Natural Scrolling Enabled Default (280): 0
libinput Send Events Modes Available (258): 1, 0
libinput Send Events Mode Enabled (259): 0, 0
libinput Send Events Mode Enabled Default (260): 0, 0
libinput Left Handed Enabled (281): 0
libinput Left Handed Enabled Default (282): 0
libinput Scroll Methods Available (283): 0, 0, 1
libinput Scroll Method Enabled (284): 0, 0, 0
libinput Scroll Method Enabled Default (285): 0, 0, 0
libinput Button Scrolling Button (286): 2
libinput Button Scrolling Button Default (287): 274
libinput Middle Emulation Enabled (288): 0
libinput Middle Emulation Enabled Default (289): 0
Device Node (261): "/dev/input/event21"
Device Product ID (262): 1160, 640
libinput Drag Lock Buttons (290): <no items>
libinput Horizontal Scroll Enabled (263): 1Thank you in advance
Offline