Arch Linux

gnunn

Member

Registered: 2013-10-21

Posts: 102

plymouth-encrypt typing speed slow

I have Arch Linux installed on a Dell XPS 15 (9560) with plymouth at boot. I have an encrypted hard drive so I use plymouth-encrypt to enable typing my password in a nice looking graphical screen rather then the console. I'm finding the typing speed to very slow with 2 second delay between keypresses.

I've done some googling and haven't seen anyone else report the same issue, thought I would post here and see if I get lucky. My mkinitcpio.conf is below.

# vim:set ft=sh
# MODULES
# The following modules are loaded before any boot hooks are
# run.  Advanced users may wish to specify all system modules
# in this array.  For instance:
#     MODULES="piix ide_disk reiserfs"
MODULES="i915"

# BINARIES
# This setting includes any additional binaries a given user may
# wish into the CPIO image.  This is run last, so it may be used to
# override the actual binaries included by a given hook
# BINARIES are dependency parsed, so you may safely ignore libraries
BINARIES=""

# FILES
# This setting is similar to BINARIES above, however, files are added
# as-is and are not parsed in any way.  This is useful for config files.
FILES=""

# HOOKS
# This is the most important setting in this file.  The HOOKS control the
# modules and scripts added to the image, and what happens at boot time.
# Order is important, and it is recommended that you do not change the
# order in which HOOKS are added.  Run 'mkinitcpio -H <hook name>' for
# help on a given hook.
# 'base' is _required_ unless you know precisely what you are doing.
# 'udev' is _required_ in order to automatically load modules
# 'filesystems' is _required_ unless you specify your fs modules in MODULES
# Examples:
##   This setup specifies all modules in the MODULES setting above.
##   No raid, lvm2, or encrypted root is needed.
#    HOOKS="base"
#
##   This setup will autodetect all modules for your system and should
##   work as a sane default
#    HOOKS="base udev autodetect block filesystems"
#
##   This setup will generate a 'full' image which supports most systems.
##   No autodetection is done.
#    HOOKS="base udev block filesystems"
#
##   This setup assembles a pata mdadm array with an encrypted root FS.
##   Note: See 'mkinitcpio -H mdadm' for more information on raid devices.
#    HOOKS="base udev block mdadm encrypt filesystems"
#
##   This setup loads an lvm2 volume group on a usb device.
#    HOOKS="base udev block lvm2 filesystems"
#
##   NOTE: If you have /usr on a separate partition, you MUST include the
#    usr, fsck and shutdown hooks.
HOOKS="base udev plymouth autodetect modconf block keyboard plymouth-encrypt lvm2 filesystems fsck"

# COMPRESSION
# Use this to compress the initramfs image. By default, gzip compression
# is used. Use 'cat' to create an uncompressed image.
#COMPRESSION="gzip"
#COMPRESSION="bzip2"
#COMPRESSION="lzma"
#COMPRESSION="xz"
#COMPRESSION="lzop"
#COMPRESSION="lz4"

COMPRESSION="cat"

# COMPRESSION_OPTIONS
# Additional options for the compressor
# COMPRESSION_OPTIONS=""

Pandoras_Fox

Member

Registered: 2018-07-29

Posts: 1

Re: plymouth-encrypt typing speed slow

I'm also getting this issue. I recently got an HP Envy 13z (2500U, 4k display) and threw Arch onto it. Works pretty well, but Plymouth is just absurdly slow when I type to decrypt.

# vim:set ft=sh
# MODULES
# The following modules are loaded before any boot hooks are
# run.  Advanced users may wish to specify all system modules
# in this array.  For instance:
#     MODULES=(piix ide_disk reiserfs)
MODULES=(amdgpu radeon)

# BINARIES
# This setting includes any additional binaries a given user may
# wish into the CPIO image.  This is run last, so it may be used to
# override the actual binaries included by a given hook
# BINARIES are dependency parsed, so you may safely ignore libraries
BINARIES=()

# FILES
# This setting is similar to BINARIES above, however, files are added
# as-is and are not parsed in any way.  This is useful for config files.
FILES=()

# HOOKS
# This is the most important setting in this file.  The HOOKS control the
# modules and scripts added to the image, and what happens at boot time.
# Order is important, and it is recommended that you do not change the
# order in which HOOKS are added.  Run 'mkinitcpio -H <hook name>' for
# help on a given hook.
# 'base' is _required_ unless you know precisely what you are doing.
# 'udev' is _required_ in order to automatically load modules
# 'filesystems' is _required_ unless you specify your fs modules in MODULES
# Examples:
##   This setup specifies all modules in the MODULES setting above.
##   No raid, lvm2, or encrypted root is needed.
#    HOOKS=(base)
#
##   This setup will autodetect all modules for your system and should
##   work as a sane default
#    HOOKS=(base udev autodetect block filesystems)
#
##   This setup will generate a 'full' image which supports most systems.
##   No autodetection is done.
#    HOOKS=(base udev block filesystems)
#
##   This setup assembles a pata mdadm array with an encrypted root FS.
##   Note: See 'mkinitcpio -H mdadm' for more information on raid devices.
#    HOOKS=(base udev block mdadm encrypt filesystems)
#
##   This setup loads an lvm2 volume group on a usb device.
#    HOOKS=(base udev block lvm2 filesystems)
#
##   NOTE: If you have /usr on a separate partition, you MUST include the
#    usr, fsck and shutdown hooks.
HOOKS=(base udev plymouth keyboard autodetect keymap modconf block plymouth-encrypt lvm2 filesystems fsck)

# COMPRESSION
# Use this to compress the initramfs image. By default, gzip compression
# is used. Use 'cat' to create an uncompressed image.
#COMPRESSION="gzip"
#COMPRESSION="bzip2"
#COMPRESSION="lzma"
#COMPRESSION="xz"
#COMPRESSION="lzop"
#COMPRESSION="lz4"

# COMPRESSION_OPTIONS
# Additional options for the compressor
#COMPRESSION_OPTIONS=()

It's a bizarre issue that doesn't seem to be mentioned anywhere else, leaves no trace in any logs, and has no real obvious cause. I'm at a loss.

hobarrera

Member

From: The Netherlands

Registered: 2011-04-12

Posts: 356

Website

Re: plymouth-encrypt typing speed slow

I had this issue with the default theme. Changing the theme to a different one seems to work around the issue, but I've no idea what's causing it.

---

AUR packages | blog| sourcehut| gitlab