You are not logged in.
- Topics: Active | Unanswered
Pages: 1
#1 2018-08-26 23:34:10
- 4ochel
- Member
- Registered: 2018-05-30
- Posts: 2
ThinkPad SSD Failure?
I'm having trouble with getting Linux working reliably on a ThinkPad T450. I believe it may be an SSD issue.
History:
- Install Arch from USB
- Reboot, it works fine
- Power off
- Power up
- Dropped into Grub Rescue
The same thing - with small variations - happens with a) CentOs 7.5 and b) Ubuntu Server, both of which I installed as a way to verify that the hardware was at issue.
I have run BIOS SSD diagnostics which do not report an error.
I've attached the dmesg...
What I suspect is most relevant:
[ 10.307092] ata1.00: exception Emask 0x10 SAct 0x280 SErr 0xc00001 action 0x6 frozen
[ 10.307124] ata1.00: irq_stat 0x08000000, interface fatal error
[ 10.307145] ata1: SError: { RecovData Handshk LinkSeq }
[ 10.307165] ata1.00: failed command: READ FPDMA QUEUED
[ 10.307185] ata1.00: cmd 60/08:38:78:08:00/00:00:19:00:00/40 tag 7 ncq 4096 in
res 40/00:44:f8:06:00/00:00:19:00:00/40 Emask 0x10 (ATA bus error)
[ 10.307235] ata1.00: status: { DRDY }
[ 10.307249] ata1.00: failed command: READ FPDMA QUEUED
[ 10.307269] ata1.00: cmd 60/08:48:00:10:00/00:00:00:00:00/40 tag 9 ncq 4096 in
res 40/00:44:f8:06:00/00:00:19:00:00/40 Emask 0x10 (ATA bus error)
[ 10.307318] ata1.00: status: { DRDY }
[ 10.307333] ata1: hard resetting link
[ 10.618233] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 10.618713] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 10.618717] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 10.619008] ata1.00: supports DRM functions and may not be fully accessible
[ 10.619504] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 10.619508] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 10.619766] ata1.00: supports DRM functions and may not be fully accessible
[ 10.619821] ata1.00: configured for UDMA/100
[ 10.619834] ata1: EH complete
[ 10.630461] ata1.00: exception Emask 0x10 SAct 0x30000000 SErr 0x800000 action 0x6 frozen
[ 10.630495] ata1.00: irq_stat 0x08000008, interface fatal error
[ 10.630517] ata1: SError: { LinkSeq }
[ 10.630532] ata1.00: failed command: READ FPDMA QUEUED
[ 10.630553] ata1.00: cmd 60/f0:e0:10:09:00/00:00:00:00:00/40 tag 28 ncq 122880 in
res 40/00:e4:10:09:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[ 10.630602] ata1.00: status: { DRDY }
[ 10.630616] ata1.00: failed command: READ FPDMA QUEUED
[ 10.630637] ata1.00: cmd 60/00:e8:00:0a:00/01:00:19:00:00/40 tag 29 ncq 131072 in
res 40/00:e4:10:09:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[ 10.630686] ata1.00: status: { DRDY }
[ 10.630702] ata1: hard resetting link
[ 10.942110] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 10.942157] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x100)
[ 10.942161] ata1.00: revalidation failed (errno=-5)
[ 14.562634] input: Logitech Wireless Mouse as /devices/pci0000:00/0000:00:14.0/usb2/2-2/2-2:1.2/0003:046D:C52B.0003/0003:046D:4055.0004/input/input7
[ 14.562777] logitech-hidpp-device 0003:046D:4055.0004: input,hidraw2: USB HID v1.11 Mouse [Logitech Wireless Mouse] on usb-0000:00:14.0-2:1
[ 15.940734] ata1: hard resetting link
[ 16.252524] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 16.253204] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 16.253214] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 16.253581] ata1.00: supports DRM functions and may not be fully accessible
[ 16.254384] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 16.254394] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 16.254724] ata1.00: supports DRM functions and may not be fully accessible
[ 16.254820] ata1.00: configured for UDMA/100
[ 16.254862] ata1: EH complete
[ 16.267437] ata1.00: exception Emask 0x10 SAct 0x3800 SErr 0x800000 action 0x6 frozen
[ 16.267470] ata1.00: irq_stat 0x08000008, interface fatal error
[ 16.267492] ata1: SError: { LinkSeq }
[ 16.267507] ata1.00: failed command: READ FPDMA QUEUED
[ 16.267529] ata1.00: cmd 60/00:58:00:05:00/01:00:19:00:00/40 tag 11 ncq 131072 in
res 40/00:64:00:07:00/00:00:1b:00:00/40 Emask 0x10 (ATA bus error)
[ 16.267579] ata1.00: status: { DRDY }
[ 16.267593] ata1.00: failed command: READ FPDMA QUEUED
[ 16.267613] ata1.00: cmd 60/80:60:00:07:00/00:00:1b:00:00/40 tag 12 ncq 65536 in
res 40/00:64:00:07:00/00:00:1b:00:00/40 Emask 0x10 (ATA bus error)
[ 16.267663] ata1.00: status: { DRDY }
[ 16.267677] ata1.00: failed command: READ FPDMA QUEUED
[ 16.267697] ata1.00: cmd 60/68:68:88:07:00/00:00:1b:00:00/40 tag 13 ncq 53248 in
res 40/00:64:00:07:00/00:00:1b:00:00/40 Emask 0x10 (ATA bus error)
[ 16.267746] ata1.00: status: { DRDY }
[ 16.267761] ata1: hard resetting link
[ 16.578715] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 16.579254] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 16.579261] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 16.579602] ata1.00: supports DRM functions and may not be fully accessible
[ 16.580284] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 16.580291] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 16.580634] ata1.00: supports DRM functions and may not be fully accessible
[ 16.580704] ata1.00: configured for UDMA/100
[ 16.580733] ata1: EH completeAll boot dmesg (the section above appears at the end):
[ 0.000000] microcode: microcode updated early to revision 0x22, date = 2015-09-11
[ 0.000000] Linux version 4.6.3-1-ARCH (builduser@tobias) (gcc version 6.1.1 20160602 (GCC) ) #1 SMP PREEMPT Fri Jun 24 21:19:13 CEST 2016
[ 0.000000] Command line: BOOT_IMAGE=boot/x86_64/vmlinuz archisobasedir=arch archisolabel=ARCH_201607 initrd=boot/intel_ucode.img,boot/x86_64/archiso.img
[ 0.000000] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
[ 0.000000] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format.
[ 0.000000] x86/fpu: Using 'eager' FPU context switches.
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009cfff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009d000-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000000fffffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000010000000-0x000000001000afff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000001000b000-0x00000000af0a9fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000af0aa000-0x00000000bcbfefff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000bcbff000-0x00000000bcd7efff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000bcd7f000-0x00000000bcdfefff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000bcdff000-0x00000000bfffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed08000-0x00000000fed08fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed10000-0x00000000fed19fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ffa00000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000043dffffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.7 present.
[ 0.000000] DMI: LENOVO 20BUS05800/20BUS05800, BIOS JBET53WW (1.18 ) 09/14/2015
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0x43e000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: write-back
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 00D0000000 mask 7FF0000000 uncachable
[ 0.000000] 1 base 00BE000000 mask 7FFE000000 uncachable
[ 0.000000] 2 base 00BD000000 mask 7FFF000000 uncachable
[ 0.000000] 3 base 00BCE00000 mask 7FFFE00000 uncachable
[ 0.000000] 4 base 00E0000000 mask 7FE0000000 uncachable
[ 0.000000] 5 base 00C0000000 mask 7FF0000000 uncachable
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] 8 disabled
[ 0.000000] 9 disabled
[ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WC UC- WT
[ 0.000000] e820: last_pfn = 0xaf0aa max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000f0100-0x000f010f] mapped at [ffff8800000f0100]
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] Base memory trampoline at [ffff880000097000] 97000 size 24576
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] BRK [0x01b4f000, 0x01b4ffff] PGTABLE
[ 0.000000] BRK [0x01b50000, 0x01b50fff] PGTABLE
[ 0.000000] BRK [0x01b51000, 0x01b51fff] PGTABLE
[ 0.000000] BRK [0x01b52000, 0x01b52fff] PGTABLE
[ 0.000000] BRK [0x01b53000, 0x01b53fff] PGTABLE
[ 0.000000] BRK [0x01b54000, 0x01b54fff] PGTABLE
[ 0.000000] RAMDISK: [mem 0x7e674000-0x7fffffff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000000F0120 000024 (v02 LENOVO)
[ 0.000000] ACPI: XSDT 0x00000000BCDFE1C0 0000F4 (v01 LENOVO TP-JB 00001180 PTEC 00000002)
[ 0.000000] ACPI: FACP 0x00000000BCDF8000 00010C (v05 LENOVO TP-JB 00001180 PTEC 00000002)
[ 0.000000] ACPI: DSDT 0x00000000BCDE3000 010F65 (v01 LENOVO TP-JB 00001180 INTL 20120711)
[ 0.000000] ACPI: FACS 0x00000000BCD68000 000040
[ 0.000000] ACPI: SLIC 0x00000000BCDFD000 000176 (v01 LENOVO TP-JB 00001180 PTEC 00000001)
[ 0.000000] ACPI: ASF! 0x00000000BCDFC000 0000A5 (v32 LENOVO TP-JB 00001180 PTEC 00000002)
[ 0.000000] ACPI: HPET 0x00000000BCDFB000 000038 (v01 LENOVO TP-JB 00001180 PTEC 00000002)
[ 0.000000] ACPI: ECDT 0x00000000BCDFA000 000052 (v01 LENOVO TP-JB 00001180 PTEC 00000002)
[ 0.000000] ACPI: APIC 0x00000000BCDF7000 000098 (v01 LENOVO TP-JB 00001180 PTEC 00000002)
[ 0.000000] ACPI: MCFG 0x00000000BCDF6000 00003C (v01 LENOVO TP-JB 00001180 PTEC 00000002)
[ 0.000000] ACPI: SSDT 0x00000000BCDF5000 000033 (v01 LENOVO TP-SSDT1 00000100 INTL 20120711)
[ 0.000000] ACPI: SSDT 0x00000000BCDF4000 000486 (v01 LENOVO TP-SSDT2 00000200 INTL 20120711)
[ 0.000000] ACPI: SSDT 0x00000000BCDE2000 0009CB (v01 LENOVO SataAhci 00001000 INTL 20120711)
[ 0.000000] ACPI: SSDT 0x00000000BCDE1000 000152 (v01 LENOVO Rmv_Batt 00001000 INTL 20120711)
[ 0.000000] ACPI: SSDT 0x00000000BCDE0000 0006C9 (v01 LENOVO Cpu0Ist 00003000 INTL 20120711)
[ 0.000000] ACPI: SSDT 0x00000000BCDDF000 000B74 (v02 LENOVO CpuSsdt 00003000 INTL 20120711)
[ 0.000000] ACPI: SSDT 0x00000000BCDDE000 000369 (v02 LENOVO CtdpB 00001000 INTL 20120711)
[ 0.000000] ACPI: SSDT 0x00000000BCDDC000 001475 (v01 LENOVO SaSsdt 00003000 INTL 20120711)
[ 0.000000] ACPI: SSDT 0x00000000BCDDB000 000394 (v02 LENOVO CppcTabl 00001000 INTL 20120711)
[ 0.000000] ACPI: PCCT 0x00000000BCDDA000 00006E (v05 LENOVO TP-JB 00001180 PTEC 00000002)
[ 0.000000] ACPI: SSDT 0x00000000BCDD9000 000AC4 (v02 LENOVO Cpc_Tabl 00001000 INTL 20120711)
[ 0.000000] ACPI: TCPA 0x00000000BCDD8000 000032 (v02 PTL LENOVO 06040000 LNVO 00000001)
[ 0.000000] ACPI: SSDT 0x00000000BCDD7000 0006A3 (v01 Intel_ TpmTable 00001000 INTL 20120711)
[ 0.000000] ACPI: UEFI 0x00000000BCDD6000 000042 (v01 LENOVO TP-JB 00001180 PTEC 00000002)
[ 0.000000] ACPI: POAT 0x00000000BCCB1000 000055 (v03 LENOVO TP-JB 00001180 PTEC 00000002)
[ 0.000000] ACPI: BATB 0x00000000BCDD5000 000046 (v01 LENOVO TP-JB 00001180 PTEC 00000002)
[ 0.000000] ACPI: FPDT 0x00000000BCDD4000 000064 (v01 LENOVO TP-JB 00001180 PTEC 00000002)
[ 0.000000] ACPI: UEFI 0x00000000BCDD3000 0002E2 (v01 LENOVO TP-JB 00001180 PTEC 00000002)
[ 0.000000] ACPI: DMAR 0x00000000BCDD2000 0000B0 (v01 LENOVO TP-JB 00001180 PTEC 00000002)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000043dffffff]
[ 0.000000] NODE_DATA(0) allocated [mem 0x43dffb000-0x43dffefff]
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.000000] Normal [mem 0x0000000100000000-0x000000043dffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009cfff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x000000000fffffff]
[ 0.000000] node 0: [mem 0x000000001000b000-0x00000000af0a9fff]
[ 0.000000] node 0: [mem 0x0000000100000000-0x000000043dffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000043dffffff]
[ 0.000000] On node 0 totalpages: 4116539
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3996 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 11139 pages used for memmap
[ 0.000000] DMA32 zone: 712863 pages, LIFO batch:31
[ 0.000000] Normal zone: 53120 pages used for memmap
[ 0.000000] Normal zone: 3399680 pages, LIFO batch:31
[ 0.000000] Reserving Intel graphics stolen memory at 0xbe000000-0xbfffffff
[ 0.000000] ACPI: PM-Timer IO Port: 0x1808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-39
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a301 base: 0xfed00000
[ 0.000000] smpboot: Allowing 8 CPUs, 4 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009d000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x10000000-0x1000afff]
[ 0.000000] PM: Registered nosave memory: [mem 0xaf0aa000-0xbcbfefff]
[ 0.000000] PM: Registered nosave memory: [mem 0xbcbff000-0xbcd7efff]
[ 0.000000] PM: Registered nosave memory: [mem 0xbcd7f000-0xbcdfefff]
[ 0.000000] PM: Registered nosave memory: [mem 0xbcdff000-0xbfffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xc0000000-0xf7ffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfc000000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfed07fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed08000-0xfed08fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed09000-0xfed0ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed10000-0xfed19fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed1a000-0xfed1bfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xff9fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xffa00000-0xffffffff]
[ 0.000000] e820: [mem 0xc0000000-0xf7ffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370452778343963 ns
[ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] percpu: Embedded 32 pages/cpu @ffff88043dc00000 s93464 r8192 d29416 u262144
[ 0.000000] pcpu-alloc: s93464 r8192 d29416 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 4052195
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=boot/x86_64/vmlinuz archisobasedir=arch archisolabel=ARCH_201607 initrd=boot/intel_ucode.img,boot/x86_64/archiso.img
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 16102912K/16466156K available (5935K kernel code, 974K rwdata, 1796K rodata, 1224K init, 1152K bss, 363244K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=8.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=8
[ 0.000000] NR_IRQS:8448 nr_irqs:760 16
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 2294.557 MHz processor
[ 0.000082] Calibrating delay loop (skipped), value calculated using timer frequency.. 4590.32 BogoMIPS (lpj=7648523)
[ 0.000089] pid_max: default: 32768 minimum: 301
[ 0.000103] ACPI: Core revision 20160108
[ 0.056115] ACPI: 12 ACPI AML tables successfully acquired and loaded
[ 0.056175] Security Framework initialized
[ 0.056178] Yama: becoming mindful.
[ 0.058927] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[ 0.067501] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.071193] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.071242] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.071874] CPU: Physical Processor ID: 0
[ 0.071878] CPU: Processor Core ID: 0
[ 0.071888] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.071890] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.071900] mce: CPU supports 7 MCE banks
[ 0.071932] CPU0: Thermal monitoring enabled (TM1)
[ 0.071953] process: using mwait in idle threads
[ 0.071960] Last level iTLB entries: 4KB 64, 2MB 8, 4MB 8
[ 0.071963] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 0, 1GB 4
[ 0.072798] Freeing SMP alternatives memory: 24K (ffffffff81a27000 - ffffffff81a2d000)
[ 0.076267] ftrace: allocating 23494 entries in 92 pages
[ 0.101871] smpboot: Max logical packages: 4
[ 0.101878] smpboot: APIC(0) Converting physical 0 to logical package 0
[ 0.101898] DMAR: Host address width 39
[ 0.101902] DMAR: DRHD base: 0x000000fed90000 flags: 0x0
[ 0.101914] DMAR: dmar0: reg_base_addr fed90000 ver 1:0 cap 1c0000c40660462 ecap 7e1ff0505e
[ 0.101918] DMAR: DRHD base: 0x000000fed91000 flags: 0x1
[ 0.101926] DMAR: dmar1: reg_base_addr fed91000 ver 1:0 cap d2008c20660462 ecap f010da
[ 0.101930] DMAR: RMRR base: 0x000000bafcc000 end: 0x000000bafe2fff
[ 0.101933] DMAR: RMRR base: 0x000000bd800000 end: 0x000000bfffffff
[ 0.101938] DMAR-IR: IOAPIC id 2 under DRHD base 0xfed91000 IOMMU 1
[ 0.101941] DMAR-IR: HPET id 0 under DRHD base 0xfed91000
[ 0.101944] DMAR-IR: x2apic is disabled because BIOS sets x2apic opt out bit.
[ 0.101947] DMAR-IR: Use 'intremap=no_x2apic_optout' to override the BIOS setting.
[ 0.102870] DMAR-IR: Enabled IRQ remapping in xapic mode
[ 0.102872] x2apic: IRQ remapping doesn't support X2APIC mode
[ 0.103598] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.136616] TSC deadline timer enabled
[ 0.136622] smpboot: CPU0: Intel(R) Core(TM) i5-5300U CPU @ 2.30GHz (family: 0x6, model: 0x3d, stepping: 0x4)
[ 0.136651] Performance Events: PEBS fmt2+, 16-deep LBR, Broadwell events, full-width counters, Intel PMU driver.
[ 0.136704] ... version: 3
[ 0.136707] ... bit width: 48
[ 0.136709] ... generic registers: 4
[ 0.136712] ... value mask: 0000ffffffffffff
[ 0.136714] ... max period: 0000ffffffffffff
[ 0.136717] ... fixed-purpose events: 3
[ 0.136719] ... event mask: 000000070000000f
[ 0.157125] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.173524] x86: Booting SMP configuration:
[ 0.173528] .... node #0, CPUs: #1 #2 #3
[ 0.456054] x86: Booted up 1 node, 4 CPUs
[ 0.456061] smpboot: Total of 4 processors activated (18375.85 BogoMIPS)
[ 0.466128] devtmpfs: initialized
[ 0.466266] x86/mm: Memory block size: 128MB
[ 0.474166] PM: Registering ACPI NVS region [mem 0xbcbff000-0xbcd7efff] (1572864 bytes)
[ 0.474435] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[ 0.474616] pinctrl core: initialized pinctrl subsystem
[ 0.474727] RTC time: 23:04:08, date: 08/26/18
[ 0.475005] NET: Registered protocol family 16
[ 0.488550] cpuidle: using governor ladder
[ 0.505235] cpuidle: using governor menu
[ 0.505349] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.505353] ACPI: bus type PCI registered
[ 0.505356] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.505681] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[ 0.505686] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[ 0.505698] PCI: Using configuration type 1 for base access
[ 0.518866] HugeTLB registered 1 GB page size, pre-allocated 0 pages
[ 0.518870] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.519412] ACPI: Added _OSI(Module Device)
[ 0.519417] ACPI: Added _OSI(Processor Device)
[ 0.519420] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.519423] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.519786] ACPI : EC: EC description table is found, configuring boot EC
[ 0.519808] ACPI : EC: EC started
[ 0.533454] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.539524] ACPI: Dynamic OEM Table Load:
[ 0.539551] ACPI: SSDT 0xFFFF88042B178000 000436 (v01 PmRef Cpu0Cst 00003001 INTL 20120711)
[ 0.541517] ACPI: Dynamic OEM Table Load:
[ 0.541539] ACPI: SSDT 0xFFFF88042B178800 0005AA (v01 PmRef ApIst 00003000 INTL 20120711)
[ 0.543643] ACPI: Dynamic OEM Table Load:
[ 0.543661] ACPI: SSDT 0xFFFF88042B013E00 000119 (v02 PmRef ApCst 00003000 INTL 20120711)
[ 0.546704] ACPI: Interpreter enabled
[ 0.546784] ACPI: (supports S0 S3 S4 S5)
[ 0.546788] ACPI: Using IOAPIC for interrupt routing
[ 0.546857] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.552630] ACPI: Power Resource [PUBS] (on)
[ 0.553679] acpi PNP0C0A:01: ACPI dock station (docks/bays count: 1)
[ 0.554419] ACPI: Power Resource [NVP3] (on)
[ 0.554484] ACPI: Power Resource [NVP2] (on)
[ 0.562386] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
[ 0.562560] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11)
[ 0.562725] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11)
[ 0.562887] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 *6 7 9 10 11)
[ 0.563049] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11)
[ 0.563175] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
[ 0.563338] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 *10 11)
[ 0.563498] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 9 10 11)
[ 0.563698] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3f])
[ 0.563709] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[ 0.563963] acpi PNP0A08:00: _OSC: platform does not support [PCIeCapability]
[ 0.564073] acpi PNP0A08:00: _OSC: not requesting control; platform does not support [PCIeCapability]
[ 0.564079] acpi PNP0A08:00: _OSC: OS requested [PCIeHotplug PME AER PCIeCapability]
[ 0.564084] acpi PNP0A08:00: _OSC: platform willing to grant [PCIeHotplug PME AER]
[ 0.564088] acpi PNP0A08:00: _OSC failed (AE_SUPPORT); disabling ASPM
[ 0.564456] PCI host bridge to bus 0000:00
[ 0.564462] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window]
[ 0.564467] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.564471] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[ 0.564475] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xfebfffff window]
[ 0.564479] pci_bus 0000:00: root bus resource [mem 0xfed40000-0xfed4bfff window]
[ 0.564483] pci_bus 0000:00: root bus resource [bus 00-3f]
[ 0.564501] pci 0000:00:00.0: [8086:1604] type 00 class 0x060000
[ 0.564697] pci 0000:00:02.0: [8086:1616] type 00 class 0x030000
[ 0.564724] pci 0000:00:02.0: reg 0x10: [mem 0xe0000000-0xe0ffffff 64bit]
[ 0.564740] pci 0000:00:02.0: reg 0x18: [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.564752] pci 0000:00:02.0: reg 0x20: [io 0x3000-0x303f]
[ 0.564941] pci 0000:00:03.0: [8086:160c] type 00 class 0x040300
[ 0.564963] pci 0000:00:03.0: reg 0x10: [mem 0xe1230000-0xe1233fff 64bit]
[ 0.565188] pci 0000:00:14.0: [8086:9cb1] type 00 class 0x0c0330
[ 0.565217] pci 0000:00:14.0: reg 0x10: [mem 0xe1220000-0xe122ffff 64bit]
[ 0.565326] pci 0000:00:14.0: PME# supported from D3hot D3cold
[ 0.565394] pci 0000:00:14.0: System wakeup disabled by ACPI
[ 0.565480] pci 0000:00:16.0: [8086:9cba] type 00 class 0x078000
[ 0.565510] pci 0000:00:16.0: reg 0x10: [mem 0xe1239000-0xe123901f 64bit]
[ 0.565621] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.565766] pci 0000:00:19.0: [8086:15a2] type 00 class 0x020000
[ 0.565791] pci 0000:00:19.0: reg 0x10: [mem 0xe1200000-0xe121ffff]
[ 0.565804] pci 0000:00:19.0: reg 0x14: [mem 0xe123e000-0xe123efff]
[ 0.565818] pci 0000:00:19.0: reg 0x18: [io 0x3080-0x309f]
[ 0.565913] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[ 0.565979] pci 0000:00:19.0: System wakeup disabled by ACPI
[ 0.566059] pci 0000:00:1b.0: [8086:9ca0] type 00 class 0x040300
[ 0.566087] pci 0000:00:1b.0: reg 0x10: [mem 0xe1234000-0xe1237fff 64bit]
[ 0.566186] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.566321] pci 0000:00:1c.0: [8086:9c9a] type 01 class 0x060400
[ 0.566428] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.566668] pci 0000:00:1c.1: [8086:9c94] type 01 class 0x060400
[ 0.566782] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.566927] pci 0000:00:1c.1: System wakeup disabled by ACPI
[ 0.567023] pci 0000:00:1d.0: [8086:9ca6] type 00 class 0x0c0320
[ 0.567051] pci 0000:00:1d.0: reg 0x10: [mem 0xe123d000-0xe123d3ff]
[ 0.567183] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.567251] pci 0000:00:1d.0: System wakeup disabled by ACPI
[ 0.567333] pci 0000:00:1f.0: [8086:9cc3] type 00 class 0x060100
[ 0.567609] pci 0000:00:1f.2: [8086:9c83] type 00 class 0x010601
[ 0.567632] pci 0000:00:1f.2: reg 0x10: [io 0x30a8-0x30af]
[ 0.567646] pci 0000:00:1f.2: reg 0x14: [io 0x30bc-0x30bf]
[ 0.567659] pci 0000:00:1f.2: reg 0x18: [io 0x30a0-0x30a7]
[ 0.567672] pci 0000:00:1f.2: reg 0x1c: [io 0x30b8-0x30bb]
[ 0.567686] pci 0000:00:1f.2: reg 0x20: [io 0x3060-0x307f]
[ 0.567699] pci 0000:00:1f.2: reg 0x24: [mem 0xe123c000-0xe123c7ff]
[ 0.567761] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.567893] pci 0000:00:1f.3: [8086:9ca2] type 00 class 0x0c0500
[ 0.567918] pci 0000:00:1f.3: reg 0x10: [mem 0xe1238000-0xe12380ff 64bit]
[ 0.567951] pci 0000:00:1f.3: reg 0x20: [io 0xefa0-0xefbf]
[ 0.568114] pci 0000:00:1f.6: [8086:9ca4] type 00 class 0x118000
[ 0.568154] pci 0000:00:1f.6: reg 0x10: [mem 0xe123b000-0xe123bfff 64bit]
[ 0.568531] pci 0000:02:00.0: [10ec:5227] type 00 class 0xff0000
[ 0.568606] pci 0000:02:00.0: reg 0x10: [mem 0xe1100000-0xe1100fff]
[ 0.569112] pci 0000:02:00.0: supports D1 D2
[ 0.569116] pci 0000:02:00.0: PME# supported from D1 D2 D3hot D3cold
[ 0.575386] pci 0000:00:1c.0: PCI bridge to [bus 02]
[ 0.575395] pci 0000:00:1c.0: bridge window [mem 0xe1100000-0xe11fffff]
[ 0.575756] pci 0000:03:00.0: [8086:095b] type 00 class 0x028000
[ 0.575999] pci 0000:03:00.0: reg 0x10: [mem 0xe1000000-0xe1001fff 64bit]
[ 0.576656] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
[ 0.582285] pci 0000:00:1c.1: PCI bridge to [bus 03]
[ 0.582295] pci 0000:00:1c.1: bridge window [mem 0xe1000000-0xe10fffff]
[ 0.584065] ACPI: Enabled 4 GPEs in block 00 to 7F
[ 0.584221] ACPI : EC: GPE = 0x25, I/O: command/status = 0x66, data = 0x62
[ 0.584443] vgaarb: setting as boot device: PCI:0000:00:02.0
[ 0.584448] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.584455] vgaarb: loaded
[ 0.584458] vgaarb: bridge control possible 0000:00:02.0
[ 0.584690] PCI: Using ACPI for IRQ routing
[ 0.586909] PCI: pci_cache_line_size set to 64 bytes
[ 0.587293] e820: reserve RAM buffer [mem 0x0009d000-0x0009ffff]
[ 0.587297] e820: reserve RAM buffer [mem 0xaf0aa000-0xafffffff]
[ 0.587300] e820: reserve RAM buffer [mem 0x43e000000-0x43fffffff]
[ 0.587584] NetLabel: Initializing
[ 0.587588] NetLabel: domain hash size = 128
[ 0.587590] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.587617] NetLabel: unlabeled traffic allowed by default
[ 0.587732] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.587747] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.589803] clocksource: Switched to clocksource hpet
[ 0.602985] VFS: Disk quotas dquot_6.6.0
[ 0.603020] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.603265] pnp: PnP ACPI init
[ 0.604172] system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.604180] system 00:00: [mem 0x000c0000-0x000c3fff] could not be reserved
[ 0.604184] system 00:00: [mem 0x000c4000-0x000c7fff] could not be reserved
[ 0.604188] system 00:00: [mem 0x000c8000-0x000cbfff] could not be reserved
[ 0.604192] system 00:00: [mem 0x000cc000-0x000cffff] could not be reserved
[ 0.604197] system 00:00: [mem 0x000d0000-0x000d3fff] has been reserved
[ 0.604201] system 00:00: [mem 0x000d4000-0x000d7fff] has been reserved
[ 0.604205] system 00:00: [mem 0x000d8000-0x000dbfff] has been reserved
[ 0.604209] system 00:00: [mem 0x000dc000-0x000dffff] has been reserved
[ 0.604213] system 00:00: [mem 0x000e0000-0x000e3fff] could not be reserved
[ 0.604218] system 00:00: [mem 0x000e4000-0x000e7fff] could not be reserved
[ 0.604222] system 00:00: [mem 0x000e8000-0x000ebfff] could not be reserved
[ 0.604226] system 00:00: [mem 0x000ec000-0x000effff] could not be reserved
[ 0.604230] system 00:00: [mem 0x000f0000-0x000fffff] could not be reserved
[ 0.604234] system 00:00: [mem 0x00100000-0xbfffffff] could not be reserved
[ 0.604239] system 00:00: [mem 0xfec00000-0xfed3ffff] could not be reserved
[ 0.604244] system 00:00: [mem 0xfed4c000-0xffffffff] could not be reserved
[ 0.604253] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.604455] pnp 00:01: [Firmware Bug]: PNP resource [mem 0xfed10000-0xfed13fff] covers only part of 0000:00:00.0 Intel MCH; extending to [mem 0xfed10000-0xfed17fff]
[ 0.604504] system 00:01: [io 0x1800-0x189f] could not be reserved
[ 0.604510] system 00:01: [io 0x0800-0x087f] has been reserved
[ 0.604514] system 00:01: [io 0x0880-0x08ff] has been reserved
[ 0.604518] system 00:01: [io 0x0900-0x097f] has been reserved
[ 0.604522] system 00:01: [io 0x0980-0x09ff] has been reserved
[ 0.604526] system 00:01: [io 0x0a00-0x0a7f] has been reserved
[ 0.604531] system 00:01: [io 0x0a80-0x0aff] has been reserved
[ 0.604535] system 00:01: [io 0x0b00-0x0b7f] has been reserved
[ 0.604539] system 00:01: [io 0x0b80-0x0bff] has been reserved
[ 0.604543] system 00:01: [io 0x15e0-0x15ef] has been reserved
[ 0.604547] system 00:01: [io 0x1600-0x167f] has been reserved
[ 0.604552] system 00:01: [io 0x1640-0x165f] has been reserved
[ 0.604559] system 00:01: [mem 0xf8000000-0xfbffffff] has been reserved
[ 0.604564] system 00:01: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.604568] system 00:01: [mem 0xfed10000-0xfed17fff] has been reserved
[ 0.604573] system 00:01: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.604577] system 00:01: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.604582] system 00:01: [mem 0xfed45000-0xfed4bfff] has been reserved
[ 0.604589] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.604732] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.604784] pnp 00:03: Plug and Play ACPI device, IDs LEN0071 PNP0303 (active)
[ 0.604835] pnp 00:04: Plug and Play ACPI device, IDs LEN200e PNP0f13 (active)
[ 0.605372] pnp 00:05: Plug and Play ACPI device, IDs SMO1200 PNP0c31 (active)
[ 0.605759] system 00:06: [mem 0xc0010000-0xc001ffff] has been reserved
[ 0.605764] system 00:06: [mem 0xc0000000-0xc000ffff] has been reserved
[ 0.605770] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.605838] pnp: PnP ACPI: found 7 devices
[ 0.614111] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[ 0.614156] pci 0000:00:1c.0: PCI bridge to [bus 02]
[ 0.614166] pci 0000:00:1c.0: bridge window [mem 0xe1100000-0xe11fffff]
[ 0.614180] pci 0000:00:1c.1: PCI bridge to [bus 03]
[ 0.614189] pci 0000:00:1c.1: bridge window [mem 0xe1000000-0xe10fffff]
[ 0.614206] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window]
[ 0.614210] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window]
[ 0.614214] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[ 0.614218] pci_bus 0000:00: resource 7 [mem 0xc0000000-0xfebfffff window]
[ 0.614222] pci_bus 0000:00: resource 8 [mem 0xfed40000-0xfed4bfff window]
[ 0.614226] pci_bus 0000:02: resource 1 [mem 0xe1100000-0xe11fffff]
[ 0.614231] pci_bus 0000:03: resource 1 [mem 0xe1000000-0xe10fffff]
[ 0.614304] NET: Registered protocol family 2
[ 0.614760] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.615257] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.615510] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.615589] UDP hash table entries: 8192 (order: 6, 262144 bytes)
[ 0.615702] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
[ 0.615895] NET: Registered protocol family 1
[ 0.615932] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[ 0.616789] PCI: CLS 64 bytes, default 64
[ 0.616899] Unpacking initramfs...
[ 8.238462] Freeing initrd memory: 26160K (ffff88007e674000 - ffff880080000000)
[ 8.238512] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 8.238519] software IO TLB [mem 0xab0aa000-0xaf0aa000] (64MB) mapped at [ffff8800ab0aa000-ffff8800af0a9fff]
[ 8.238641] RAPL PMU: API unit is 2^-32 Joules, 4 fixed counters, 655360 ms ovfl timer
[ 8.238644] RAPL PMU: hw unit of domain pp0-core 2^-14 Joules
[ 8.238647] RAPL PMU: hw unit of domain package 2^-14 Joules
[ 8.238649] RAPL PMU: hw unit of domain dram 2^-14 Joules
[ 8.238652] RAPL PMU: hw unit of domain pp1-gpu 2^-14 Joules
[ 8.238917] Scanning for low memory corruption every 60 seconds
[ 8.239612] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 8.240777] Initialise system trusted keyring
[ 8.240965] workingset: timestamp_bits=38 max_order=22 bucket_order=0
[ 8.244728] zbud: loaded
[ 8.245316] Key type big_key registered
[ 8.245838] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 8.245922] io scheduler noop registered
[ 8.245930] io scheduler deadline registered
[ 8.246003] io scheduler cfq registered (default)
[ 8.246600] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 8.246617] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 8.246664] intel_idle: MWAIT substates: 0x11142120
[ 8.246667] intel_idle: v0.4.1 model 0x3D
[ 8.247183] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 8.247234] GHES: HEST is not enabled!
[ 8.247366] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 8.248120] Linux agpgart interface v0.103
[ 8.248862] rtc_cmos 00:02: RTC can wake from S4
[ 8.249061] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 8.249105] rtc_cmos 00:02: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 8.249133] Intel P-state driver initializing.
[ 8.320340] ledtrig-cpu: registered to indicate activity on CPUs
[ 8.321196] NET: Registered protocol family 10
[ 8.321397] NET: Registered protocol family 17
[ 8.321592] microcode: CPU0 sig=0x306d4, pf=0x40, revision=0x22
[ 8.321601] microcode: CPU1 sig=0x306d4, pf=0x40, revision=0x22
[ 8.321607] microcode: CPU2 sig=0x306d4, pf=0x40, revision=0x22
[ 8.321617] microcode: CPU3 sig=0x306d4, pf=0x40, revision=0x22
[ 8.321654] microcode: Microcode Update Driver: v2.01 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 8.321794] registered taskstats version 1
[ 8.321808] Loading compiled-in X.509 certificates
[ 8.321828] zswap: loaded using pool lzo/zbud
[ 8.322378] Magic number: 14:919:100
[ 8.322475] rtc_cmos 00:02: setting system clock to 2018-08-26 23:04:16 UTC (1535324656)
[ 8.322551] PM: Hibernation image not present or could not be loaded.
[ 8.323603] Freeing unused kernel memory: 1224K (ffffffff818f5000 - ffffffff81a27000)
[ 8.323605] Write protecting the kernel read-only data: 8192k
[ 8.323785] Freeing unused kernel memory: 192K (ffff8800015d0000 - ffff880001600000)
[ 8.324503] Freeing unused kernel memory: 252K (ffff8800017c1000 - ffff880001800000)
[ 8.330792] random: systemd-tmpfile urandom read with 5 bits of entropy available
[ 8.349215] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
[ 8.349381] ACPI: Lid Switch [LID]
[ 8.349441] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1
[ 8.349444] ACPI: Sleep Button [SLPB]
[ 8.349509] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 8.349511] ACPI: Power Button [PWRF]
[ 8.350078] FUJITSU Extended Socket Network Device Driver - version 1.0 - Copyright (c) 2015 FUJITSU LIMITED
[ 8.351312] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
[ 8.352848] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 8.352912] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 8.355580] wmi: Mapper loaded
[ 8.357288] rtsx_pci 0000:02:00.0: rtsx_pci_acquire_irq: pcr->msi_en = 1, pci->irq = 42
[ 8.357404] pps_core: LinuxPPS API ver. 1 registered
[ 8.357407] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 8.357654] PTP clock support registered
[ 8.359499] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[ 8.359501] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 8.359502] ACPI: bus type USB registered
[ 8.359525] usbcore: registered new interface driver usbfs
[ 8.359535] usbcore: registered new interface driver hub
[ 8.359559] usbcore: registered new device driver usb
[ 8.359621] [drm] Initialized drm 1.1.0 20060810
[ 8.359898] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.360083] ehci-pci: EHCI PCI platform driver
[ 8.361241] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[ 8.364761] SCSI subsystem initialized
[ 8.366739] libata version 3.00 loaded.
[ 8.380920] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 8.556464] e1000e 0000:00:19.0 eth0: registered PHC clock
[ 8.556471] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 50:7b:9d:58:7d:17
[ 8.556475] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection
[ 8.556505] e1000e 0000:00:19.0 eth0: MAC: 11, PHY: 12, PBA No: 1000FF-0FF
[ 8.556823] ehci-pci 0000:00:1d.0: EHCI Host Controller
[ 8.556843] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 8.556866] ehci-pci 0000:00:1d.0: debug port 2
[ 8.560784] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[ 8.560815] ehci-pci 0000:00:1d.0: irq 23, io mem 0xe123d000
[ 8.570316] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 8.570570] hub 1-0:1.0: USB hub found
[ 8.570576] hub 1-0:1.0: 3 ports detected
[ 8.570921] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 8.570930] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[ 8.572002] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x00009810
[ 8.572006] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 8.572177] hub 2-0:1.0: USB hub found
[ 8.572191] hub 2-0:1.0: 11 ports detected
[ 8.573108] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 8.573111] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
[ 8.573225] hub 3-0:1.0: USB hub found
[ 8.573234] hub 3-0:1.0: 4 ports detected
[ 8.573779] ahci 0000:00:1f.2: version 3.0
[ 8.583988] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 3 ports 6 Gbps 0x1 impl SATA mode
[ 8.583992] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo only pio slum part deso sadm sds apst
[ 8.584391] scsi host0: ahci
[ 8.584531] scsi host1: ahci
[ 8.584684] scsi host2: ahci
[ 8.584736] ata1: SATA max UDMA/133 abar m2048@0xe123c000 port 0xe123c100 irq 45
[ 8.584738] ata2: DUMMY
[ 8.584739] ata3: DUMMY
[ 8.585332] [drm] Memory usable by graphics device = 4096M
[ 8.585335] [drm] Replacing VGA console driver
[ 8.585909] Console: switching to colour dummy device 80x25
[ 8.592167] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 8.592171] [drm] Driver supports precise vblank timestamp query.
[ 8.592449] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 8.627395] ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
[ 8.627795] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input5
[ 8.627836] [drm] Initialized i915 1.6.0 20160229 for 0000:00:02.0 on minor 0
[ 8.841767] fbcon: inteldrmfb (fb0) is primary device
[ 8.876992] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 8.894413] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 8.895025] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 8.895030] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 8.895356] ata1.00: supports DRM functions and may not be fully accessible
[ 8.895444] ata1.00: ATA-9: MTFDDAK256MAM-1K12, 08TH, max UDMA/100
[ 8.895447] ata1.00: 500118192 sectors, multi 1: LBA48 NCQ (depth 31/32), AA
[ 8.896128] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 8.896133] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 8.896456] ata1.00: supports DRM functions and may not be fully accessible
[ 8.896555] ata1.00: configured for UDMA/100
[ 8.897074] scsi 0:0:0:0: Direct-Access ATA MTFDDAK256MAM-1K 08TH PQ: 0 ANSI: 5
[ 8.930331] usb 2-1: new high-speed USB device number 2 using xhci_hcd
[ 9.001067] hub 1-1:1.0: USB hub found
[ 9.001138] hub 1-1:1.0: 8 ports detected
[ 9.109506] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 9.109734] scsi host3: usb-storage 2-1:1.0
[ 9.109906] usbcore: registered new interface driver usb-storage
[ 9.110673] usbcore: registered new interface driver uas
[ 9.240419] tsc: Refined TSC clocksource calibration: 2294.684 MHz
[ 9.240424] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x21139776891, max_idle_ns: 440795250948 ns
[ 9.263711] usb 2-2: new full-speed USB device number 3 using xhci_hcd
[ 9.444257] hidraw: raw HID events driver (C) Jiri Kosina
[ 9.449080] usbcore: registered new interface driver usbhid
[ 9.449082] usbhid: USB HID core driver
[ 9.450620] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:14.0-2/input2
[ 9.566491] input: Logitech K540/K545 as /devices/pci0000:00/0000:00:14.0/usb2/2-2/2-2:1.2/0003:046D:C52B.0003/0003:046D:4076.0005/input/input6
[ 9.566614] logitech-hidpp-device 0003:046D:4076.0005: input,hidraw1: USB HID v1.11 Keyboard [Logitech K540/K545] on usb-0000:00:14.0-2:2
[ 9.600413] usb 2-5: new full-speed USB device number 4 using xhci_hcd
[ 9.943758] usb 2-8: new high-speed USB device number 5 using xhci_hcd
[ 10.111222] scsi 3:0:0:0: Direct-Access SMI USB DISK 1100 PQ: 0 ANSI: 4
[ 10.113410] sd 0:0:0:0: [sda] 500118192 512-byte logical blocks: (256 GB/238 GiB)
[ 10.113546] sd 0:0:0:0: [sda] Write Protect is off
[ 10.113552] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 10.113597] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 10.113970] sd 3:0:0:0: [sdb] 7866368 512-byte logical blocks: (4.03 GB/3.75 GiB)
[ 10.114228] sda: sda1 sda2
[ 10.114441] sd 0:0:0:0: [sda] Attached SCSI disk
[ 10.114458] sd 3:0:0:0: [sdb] Write Protect is off
[ 10.114461] sd 3:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 10.114946] sd 3:0:0:0: [sdb] No Caching mode page found
[ 10.114947] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[ 10.117116] sdb: sdb1 sdb2
[ 10.118680] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[ 10.240552] clocksource: Switched to clocksource tsc
[ 10.250715] Console: switching to colour frame buffer device 200x56
[ 10.261358] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 10.307092] ata1.00: exception Emask 0x10 SAct 0x280 SErr 0xc00001 action 0x6 frozen
[ 10.307124] ata1.00: irq_stat 0x08000000, interface fatal error
[ 10.307145] ata1: SError: { RecovData Handshk LinkSeq }
[ 10.307165] ata1.00: failed command: READ FPDMA QUEUED
[ 10.307185] ata1.00: cmd 60/08:38:78:08:00/00:00:19:00:00/40 tag 7 ncq 4096 in
res 40/00:44:f8:06:00/00:00:19:00:00/40 Emask 0x10 (ATA bus error)
[ 10.307235] ata1.00: status: { DRDY }
[ 10.307249] ata1.00: failed command: READ FPDMA QUEUED
[ 10.307269] ata1.00: cmd 60/08:48:00:10:00/00:00:00:00:00/40 tag 9 ncq 4096 in
res 40/00:44:f8:06:00/00:00:19:00:00/40 Emask 0x10 (ATA bus error)
[ 10.307318] ata1.00: status: { DRDY }
[ 10.307333] ata1: hard resetting link
[ 10.618233] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 10.618713] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 10.618717] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 10.619008] ata1.00: supports DRM functions and may not be fully accessible
[ 10.619504] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 10.619508] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 10.619766] ata1.00: supports DRM functions and may not be fully accessible
[ 10.619821] ata1.00: configured for UDMA/100
[ 10.619834] ata1: EH complete
[ 10.630461] ata1.00: exception Emask 0x10 SAct 0x30000000 SErr 0x800000 action 0x6 frozen
[ 10.630495] ata1.00: irq_stat 0x08000008, interface fatal error
[ 10.630517] ata1: SError: { LinkSeq }
[ 10.630532] ata1.00: failed command: READ FPDMA QUEUED
[ 10.630553] ata1.00: cmd 60/f0:e0:10:09:00/00:00:00:00:00/40 tag 28 ncq 122880 in
res 40/00:e4:10:09:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[ 10.630602] ata1.00: status: { DRDY }
[ 10.630616] ata1.00: failed command: READ FPDMA QUEUED
[ 10.630637] ata1.00: cmd 60/00:e8:00:0a:00/01:00:19:00:00/40 tag 29 ncq 131072 in
res 40/00:e4:10:09:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[ 10.630686] ata1.00: status: { DRDY }
[ 10.630702] ata1: hard resetting link
[ 10.942110] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 10.942157] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x100)
[ 10.942161] ata1.00: revalidation failed (errno=-5)
[ 14.562634] input: Logitech Wireless Mouse as /devices/pci0000:00/0000:00:14.0/usb2/2-2/2-2:1.2/0003:046D:C52B.0003/0003:046D:4055.0004/input/input7
[ 14.562777] logitech-hidpp-device 0003:046D:4055.0004: input,hidraw2: USB HID v1.11 Mouse [Logitech Wireless Mouse] on usb-0000:00:14.0-2:1
[ 15.940734] ata1: hard resetting link
[ 16.252524] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 16.253204] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 16.253214] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 16.253581] ata1.00: supports DRM functions and may not be fully accessible
[ 16.254384] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 16.254394] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 16.254724] ata1.00: supports DRM functions and may not be fully accessible
[ 16.254820] ata1.00: configured for UDMA/100
[ 16.254862] ata1: EH complete
[ 16.267437] ata1.00: exception Emask 0x10 SAct 0x3800 SErr 0x800000 action 0x6 frozen
[ 16.267470] ata1.00: irq_stat 0x08000008, interface fatal error
[ 16.267492] ata1: SError: { LinkSeq }
[ 16.267507] ata1.00: failed command: READ FPDMA QUEUED
[ 16.267529] ata1.00: cmd 60/00:58:00:05:00/01:00:19:00:00/40 tag 11 ncq 131072 in
res 40/00:64:00:07:00/00:00:1b:00:00/40 Emask 0x10 (ATA bus error)
[ 16.267579] ata1.00: status: { DRDY }
[ 16.267593] ata1.00: failed command: READ FPDMA QUEUED
[ 16.267613] ata1.00: cmd 60/80:60:00:07:00/00:00:1b:00:00/40 tag 12 ncq 65536 in
res 40/00:64:00:07:00/00:00:1b:00:00/40 Emask 0x10 (ATA bus error)
[ 16.267663] ata1.00: status: { DRDY }
[ 16.267677] ata1.00: failed command: READ FPDMA QUEUED
[ 16.267697] ata1.00: cmd 60/68:68:88:07:00/00:00:1b:00:00/40 tag 13 ncq 53248 in
res 40/00:64:00:07:00/00:00:1b:00:00/40 Emask 0x10 (ATA bus error)
[ 16.267746] ata1.00: status: { DRDY }
[ 16.267761] ata1: hard resetting link
[ 16.578715] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 16.579254] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 16.579261] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 16.579602] ata1.00: supports DRM functions and may not be fully accessible
[ 16.580284] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 16.580291] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 16.580634] ata1.00: supports DRM functions and may not be fully accessible
[ 16.580704] ata1.00: configured for UDMA/100
[ 16.580733] ata1: EH completeOffline
#2 2018-08-26 23:45:59
- jasonwryan
- Anarchist
- From: .nz
- Registered: 2009-05-09
- Posts: 30,426
- Website
Re: ThinkPad SSD Failure?
microcode: microcode updated early to revision 0x22, date = 2015-09-11
Linux version 4.6.3-1-ARCH (builduser@tobias) (gcc version 6.1.1 20160602 (GCC) ) #1 SMP PREEMPT Fri Jun 24 21:19:13 CEST 2016It's 2018.
Moving to NC...
Offline
Pages: 1