You are not logged in.

Pages: 1

#1 2020-04-21 17:12:03

charlie
Member
Registered: 2013-09-18
Posts: 57

Installing Xfce (with nvidia)

I've been trying to add Xfce as a new DE to choose from. So far I didnt succeed. I'm running on Gnome right now.

I've tried to follow the instructions from the wiki (well you only need to install two packages and launch it?).

When I try to login after selecting xfce DE, the computer hang a little bit, displays nothing then brings me back to the login screen. I've tried to investigate the reason of this failure. From the Xorg log I see that there's an issue when loading the module for the graphic card. (it's an nvidia). I'm not sure what to do about this. I've tried a few things, mainly using google to navigate among the plethora of obsolete tutorials and half relevant forum posts on the topic. The results has been quite frustrating so I figure that what I really need is a proper method to investigate further.

The nvidia card works fine with cuda/tensorflow. That's essential for me. I don't want to do anything that might risk breaking that. I don't really care about video quality I just want my computing libs to continue using the GPU as it should.

I am asking advice on how to proceed.

Here is the important things:
1. I need to know what are the necessary and sufficient conditions for cuda/tensorflow to continue working fine with the GPU. I need to know what I can and cannot do while guaranteeing that this doesnt change.
2.  There might some configuration file, some options somewhere I can set to make xfce works. I need to find that. (for example there was a forum where somebody modified their xorg.conf, putting in the BusId for the card, I did that but this didn't work).
3. I need to know which module i should install/load/remove.
4. I need to know where to find diagnostic data about what's going wrong.

I can continue googling, but what im really asking is what is the efficient way to find out about the above points?

Last edited by charlie (2020-04-21 17:13:00)

Offline

#2 2020-04-21 17:15:06

Trilby
Inspector Parrot
Registered: 2011-11-29
Posts: 30,520
Website

Re: Installing Xfce (with nvidia)

Post your xorg.log.  If you were running Gnome on xorg, post a log from a functional gnome session as well.  If you've not been running Gnome on xorg, then that's likely the problem: you have to configure Xorg and your video drivers first.

"UNIX is simple and coherent" - Dennis Ritchie; "GNU's Not Unix" - Richard Stallman

Offline

#3 2020-04-21 17:20:58

charlie
Member
Registered: 2013-09-18
Posts: 57

Re: Installing Xfce (with nvidia)

I'm happy to post my xorg.log but my question is more about, how do I figure this out on my own.
Here it is:

[    63.157] (--) Log file renamed from "/home/user/.local/share/xorg/Xorg.pid-824.log" to "/home/user/.local/share/xorg/Xorg.0.log"
[    63.159] (WW) Failed to open protocol names file lib/xorg/protocol.txt
[    63.159] 
X.Org X Server 1.20.8
X Protocol Version 11, Revision 0
[    63.159] Build Operating System: Linux Arch Linux
[    63.159] Current Operating System: Linux gloomymush 5.6.5-arch3-1 #1 SMP PREEMPT Sun, 19 Apr 2020 13:14:25 +0000 x86_64
[    63.159] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=981ba50f-ec0d-4f41-954d-8cc886630ec1 rw nvidia-drm.modeset=1
[    63.160] Build Date: 30 March 2020  05:05:45AM
[    63.160]  
[    63.160] Current version of pixman: 0.38.4
[    63.160] 	Before reporting problems, check http://wiki.x.org
	to make sure that you have the latest version.
[    63.160] Markers: (--) probed, (**) from config file, (==) default setting,
	(++) from command line, (!!) notice, (II) informational,
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[    63.160] (==) Log file: "/home/user/.local/share/xorg/Xorg.0.log", Time: Mon Apr 20 19:09:07 2020
[    63.177] (==) Using config file: "/etc/X11/xorg.conf"
[    63.177] (==) Using config directory: "/etc/X11/xorg.conf.d"
[    63.177] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[    63.216] (==) ServerLayout "Layout0"
[    63.216] (**) |-->Screen "Screen0" (0)
[    63.216] (**) |   |-->Monitor "Monitor0"
[    63.217] (**) |   |-->Device "Device0"
[    63.218] (**) |-->Input Device "Keyboard0"
[    63.218] (**) |-->Input Device "Mouse0"
[    63.218] (==) Automatically adding devices
[    63.218] (==) Automatically enabling devices
[    63.218] (==) Automatically adding GPU devices
[    63.218] (==) Automatically binding GPU devices
[    63.218] (==) Max clients allowed: 256, resource mask: 0x1fffff
[    63.218] (WW) The directory "/usr/share/fonts/Type1" does not exist.
[    63.218] 	Entry deleted from font path.
[    63.218] (==) FontPath set to:
	/usr/share/fonts/misc,
	/usr/share/fonts/TTF,
	/usr/share/fonts/OTF,
	/usr/share/fonts/100dpi,
	/usr/share/fonts/75dpi
[    63.218] (==) ModulePath set to "/usr/lib/xorg/modules"
[    63.218] (WW) Hotplugging is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
[    63.218] (WW) Disabling Keyboard0
[    63.218] (WW) Disabling Mouse0
[    63.218] (II) Module ABI versions:
[    63.218] 	X.Org ANSI C Emulation: 0.4
[    63.218] 	X.Org Video Driver: 24.1
[    63.218] 	X.Org XInput driver : 24.1
[    63.218] 	X.Org Server Extension : 10.0
[    63.220] (++) using VT number 2

[    63.224] (II) systemd-logind: took control of session /org/freedesktop/login1/session/_32
[    63.226] (II) xfree86: Adding drm device (/dev/dri/card0)
[    63.228] (II) systemd-logind: got fd for /dev/dri/card0 226:0 fd 11 paused 0
[    63.233] (--) PCI:*(0@0:2:0) 8086:191b:1558:5500 rev 6, Mem @ 0xdd000000/16777216, 0xb0000000/268435456, I/O @ 0x0000f000/64, BIOS @ 0x????????/131072
[    63.234] (--) PCI: (1@0:0:0) 10de:139a:1558:5500 rev 162, Mem @ 0xde000000/16777216, 0xc0000000/268435456, 0xd0000000/33554432, I/O @ 0x0000e000/128, BIOS @ 0x????????/524288
[    63.234] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[    63.234] (II) LoadModule: "glx"
[    63.287] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[    63.302] (II) Module glx: vendor="X.Org Foundation"
[    63.302] 	compiled for 1.20.8, module version = 1.0.0
[    63.302] 	ABI class: X.Org Server Extension, version 10.0
[    63.302] (II) LoadModule: "nvidia"
[    63.302] (II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
[    63.356] (II) Module nvidia: vendor="NVIDIA Corporation"
[    63.356] 	compiled for 1.6.99.901, module version = 1.0.0
[    63.356] 	Module class: X.Org Video Driver
[    63.363] (II) NVIDIA dlloader X Driver  440.82  Wed Apr  1 19:50:17 UTC 2020
[    63.363] (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
[    63.364] xf86EnableIOPorts: failed to set IOPL for I/O (Operation not permitted)
[    63.371] (II) Loading sub module "fb"
[    63.371] (II) LoadModule: "fb"
[    63.371] (II) Loading /usr/lib/xorg/modules/libfb.so
[    63.386] (II) Module fb: vendor="X.Org Foundation"
[    63.386] 	compiled for 1.20.8, module version = 1.0.0
[    63.386] 	ABI class: X.Org ANSI C Emulation, version 0.4
[    63.386] (II) Loading sub module "wfb"
[    63.386] (II) LoadModule: "wfb"
[    63.386] (II) Loading /usr/lib/xorg/modules/libwfb.so
[    63.395] (II) Module wfb: vendor="X.Org Foundation"
[    63.395] 	compiled for 1.20.8, module version = 1.0.0
[    63.395] 	ABI class: X.Org ANSI C Emulation, version 0.4
[    63.395] (II) Loading sub module "ramdac"
[    63.395] (II) LoadModule: "ramdac"
[    63.395] (II) Module "ramdac" already built-in
[    63.397] (WW) VGA arbiter: cannot open kernel arbiter, no multi-card support
[    63.397] (**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32
[    63.397] (==) NVIDIA(0): RGB weight 888
[    63.397] (==) NVIDIA(0): Default visual is TrueColor
[    63.397] (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
[    63.398] (**) NVIDIA(0): Enabling 2D acceleration
[    63.398] (II) Loading sub module "glxserver_nvidia"
[    63.398] (II) LoadModule: "glxserver_nvidia"
[    63.399] (WW) Warning, couldn't open module glxserver_nvidia
[    63.399] (EE) NVIDIA: Failed to load module "glxserver_nvidia" (module does not exist, 0)
[    63.399] (EE) NVIDIA(0): Failed to initialize the GLX module; please check in your X
[    63.399] (EE) NVIDIA(0):     log file that the GLX module has been loaded in your X
[    63.399] (EE) NVIDIA(0):     server, and that the module is the NVIDIA GLX module.  If
[    63.399] (EE) NVIDIA(0):     you continue to encounter problems, Please try
[    63.399] (EE) NVIDIA(0):     reinstalling the NVIDIA driver.
[    63.399] (II) NVIDIA: The X server does not support PRIME Render Offload.
[    63.481] (II) NVIDIA(0): NVIDIA GPU GeForce GTX 950M (GM107-A) at PCI:1:0:0 (GPU-0)
[    63.481] (--) NVIDIA(0): Memory: 2097152 kBytes
[    63.481] (--) NVIDIA(0): VideoBIOS: 82.07.95.00.2e
[    63.481] (II) NVIDIA(0): Detected PCI Express Link width: 16X
[    63.481] (II) NVIDIA(0): Validated MetaModes:
[    63.481] (II) NVIDIA(0):     "NULL"
[    63.481] (II) NVIDIA(0): Virtual screen size determined to be 640 x 480
[    63.481] (WW) NVIDIA(0): Unable to get display device for DPI computation.
[    63.481] (==) NVIDIA(0): DPI set to (75, 75); computed from built-in default
[    63.481] (WW) NVIDIA: Failed to bind sideband socket to
[    63.481] (WW) NVIDIA:     '/var/run/nvidia-xdriver-0c75c8b1' Permission denied
[    63.481] (II) NVIDIA: Using 6144.00 MB of virtual memory for indirect memory
[    63.481] (II) NVIDIA:     access.
[    63.485] (II) NVIDIA(0): ACPI: failed to connect to the ACPI event daemon; the daemon
[    63.485] (II) NVIDIA(0):     may not be running or the "AcpidSocketPath" X
[    63.485] (II) NVIDIA(0):     configuration option may not be set correctly.  When the
[    63.485] (II) NVIDIA(0):     ACPI event daemon is available, the NVIDIA X driver will
[    63.485] (II) NVIDIA(0):     try to use it to receive ACPI event notifications.  For
[    63.485] (II) NVIDIA(0):     details, please see the "ConnectToAcpid" and
[    63.485] (II) NVIDIA(0):     "AcpidSocketPath" X configuration options in Appendix B: X
[    63.485] (II) NVIDIA(0):     Config Options in the README.
[    63.514] (II) NVIDIA(0): Setting mode "NULL"
[    63.530] (==) NVIDIA(0): Disabling shared memory pixmaps
[    63.530] (==) NVIDIA(0): Backing store enabled
[    63.530] (==) NVIDIA(0): Silken mouse disabled
[    63.530] (**) NVIDIA(0): DPMS enabled
[    63.530] (II) Loading sub module "dri2"
[    63.530] (II) LoadModule: "dri2"
[    63.530] (II) Module "dri2" already built-in
[    63.530] (II) NVIDIA(0): [DRI2] Setup complete
[    63.530] (II) NVIDIA(0): [DRI2]   VDPAU driver: nvidia
[    63.531] (II) Initializing extension Generic Event Extension
[    63.531] (II) Initializing extension SHAPE
[    63.531] (II) Initializing extension MIT-SHM
[    63.531] (II) Initializing extension XInputExtension
[    63.531] (II) Initializing extension XTEST
[    63.531] (II) Initializing extension BIG-REQUESTS
[    63.531] (II) Initializing extension SYNC
[    63.531] (II) Initializing extension XKEYBOARD
[    63.531] (II) Initializing extension XC-MISC
[    63.531] (II) Initializing extension SECURITY
[    63.531] (II) Initializing extension XFIXES
[    63.531] (II) Initializing extension RENDER
[    63.531] (II) Initializing extension RANDR
[    63.531] (II) Initializing extension COMPOSITE
[    63.531] (II) Initializing extension DAMAGE
[    63.531] (II) Initializing extension MIT-SCREEN-SAVER
[    63.531] (II) Initializing extension DOUBLE-BUFFER
[    63.531] (II) Initializing extension RECORD
[    63.531] (II) Initializing extension DPMS
[    63.531] (II) Initializing extension Present
[    63.531] (II) Initializing extension DRI3
[    63.531] (II) Initializing extension X-Resource
[    63.531] (II) Initializing extension XVideo
[    63.531] (II) Initializing extension XVideo-MotionCompensation
[    63.531] (II) Initializing extension GLX
[    63.531] (II) AIGLX: Screen 0 is not DRI2 capable
[    63.584] (II) IGLX: Loaded and initialized swrast
[    63.584] (II) GLX: Initialized DRISWRAST GL provider for screen 0
[    63.584] (II) Initializing extension XFree86-VidModeExtension
[    63.584] (II) Initializing extension XFree86-DGA
[    63.584] (II) Initializing extension XFree86-DRI
[    63.584] (II) Initializing extension DRI2
[    63.584] (II) Initializing extension NV-GLX
[    63.584] (II) Initializing extension NV-CONTROL
[    63.644] (II) config/udev: Adding input device Power Button (/dev/input/event3)
[    63.644] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[    63.644] (**) Power Button: Applying InputClass "system-keyboard"
[    63.644] (II) LoadModule: "libinput"
[    63.644] (II) Loading /usr/lib/xorg/modules/input/libinput_drv.so
[    63.653] (II) Module libinput: vendor="X.Org Foundation"
[    63.653] 	compiled for 1.20.7, module version = 0.29.0
[    63.653] 	Module class: X.Org XInput Driver
[    63.653] 	ABI class: X.Org XInput driver, version 24.1
[    63.653] (II) Using input driver 'libinput' for 'Power Button'
[    63.654] (II) systemd-logind: got fd for /dev/input/event3 13:67 fd 23 paused 0
[    63.654] (**) Power Button: always reports core events
[    63.654] (**) Option "Device" "/dev/input/event3"
[    63.654] (**) Option "_source" "server/udev"
[    63.655] (II) event3  - Power Button: is tagged by udev as: Keyboard
[    63.655] (II) event3  - Power Button: device is a keyboard
[    63.655] (II) event3  - Power Button: device removed
[    63.655] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input3/event3"
[    63.655] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[    63.655] (**) Option "xkb_layout" "fr,gb"
[    63.655] (**) Option "xkb_variant" "azerty,"
[    63.672] (II) event3  - Power Button: is tagged by udev as: Keyboard
[    63.672] (II) event3  - Power Button: device is a keyboard
[    63.673] (II) config/udev: Adding input device Video Bus (/dev/input/event10)
[    63.673] (**) Video Bus: Applying InputClass "libinput keyboard catchall"
[    63.673] (**) Video Bus: Applying InputClass "system-keyboard"
[    63.673] (II) Using input driver 'libinput' for 'Video Bus'
[    63.674] (II) systemd-logind: got fd for /dev/input/event10 13:74 fd 26 paused 0
[    63.674] (**) Video Bus: always reports core events
[    63.674] (**) Option "Device" "/dev/input/event10"
[    63.674] (**) Option "_source" "server/udev"
[    63.675] (II) event10 - Video Bus: is tagged by udev as: Keyboard
[    63.675] (II) event10 - Video Bus: device is a keyboard
[    63.675] (II) event10 - Video Bus: device removed
[    63.675] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input16/event10"
[    63.675] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[    63.675] (**) Option "xkb_layout" "fr,gb"
[    63.675] (**) Option "xkb_variant" "azerty,"
[    63.676] (II) event10 - Video Bus: is tagged by udev as: Keyboard
[    63.676] (II) event10 - Video Bus: device is a keyboard
[    63.677] (II) config/udev: Adding input device Video Bus (/dev/input/event11)
[    63.677] (**) Video Bus: Applying InputClass "libinput keyboard catchall"
[    63.677] (**) Video Bus: Applying InputClass "system-keyboard"
[    63.677] (II) Using input driver 'libinput' for 'Video Bus'
[    63.678] (II) systemd-logind: got fd for /dev/input/event11 13:75 fd 27 paused 0
[    63.678] (**) Video Bus: always reports core events
[    63.678] (**) Option "Device" "/dev/input/event11"
[    63.678] (**) Option "_source" "server/udev"
[    63.679] (II) event11 - Video Bus: is tagged by udev as: Keyboard
[    63.679] (II) event11 - Video Bus: device is a keyboard
[    63.679] (II) event11 - Video Bus: device removed
[    63.679] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:12/LNXVIDEO:01/input/input17/event11"
[    63.679] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 8)
[    63.679] (**) Option "xkb_layout" "fr,gb"
[    63.679] (**) Option "xkb_variant" "azerty,"
[    63.681] (II) event11 - Video Bus: is tagged by udev as: Keyboard
[    63.681] (II) event11 - Video Bus: device is a keyboard
[    63.681] (II) config/udev: Adding input device Power Button (/dev/input/event0)
[    63.682] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[    63.682] (**) Power Button: Applying InputClass "system-keyboard"
[    63.682] (II) Using input driver 'libinput' for 'Power Button'
[    63.682] (II) systemd-logind: got fd for /dev/input/event0 13:64 fd 28 paused 0
[    63.682] (**) Power Button: always reports core events
[    63.682] (**) Option "Device" "/dev/input/event0"
[    63.682] (**) Option "_source" "server/udev"
[    63.683] (II) event0  - Power Button: is tagged by udev as: Keyboard
[    63.683] (II) event0  - Power Button: device is a keyboard
[    63.683] (II) event0  - Power Button: device removed
[    63.684] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0/event0"
[    63.684] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 9)
[    63.684] (**) Option "xkb_layout" "fr,gb"
[    63.684] (**) Option "xkb_variant" "azerty,"
[    63.684] (II) event0  - Power Button: is tagged by udev as: Keyboard
[    63.685] (II) event0  - Power Button: device is a keyboard
[    63.685] (II) config/udev: Adding input device Lid Switch (/dev/input/event2)
[    63.685] (II) No input driver specified, ignoring this device.
[    63.685] (II) This device may have been added with another device file.
[    63.686] (II) config/udev: Adding input device Sleep Button (/dev/input/event1)
[    63.686] (**) Sleep Button: Applying InputClass "libinput keyboard catchall"
[    63.686] (**) Sleep Button: Applying InputClass "system-keyboard"
[    63.686] (II) Using input driver 'libinput' for 'Sleep Button'
[    63.686] (II) systemd-logind: got fd for /dev/input/event1 13:65 fd 29 paused 0
[    63.686] (**) Sleep Button: always reports core events
[    63.686] (**) Option "Device" "/dev/input/event1"
[    63.686] (**) Option "_source" "server/udev"
[    63.687] (II) event1  - Sleep Button: is tagged by udev as: Keyboard
[    63.687] (II) event1  - Sleep Button: device is a keyboard
[    63.687] (II) event1  - Sleep Button: device removed
[    63.687] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1/event1"
[    63.687] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 10)
[    63.687] (**) Option "xkb_layout" "fr,gb"
[    63.687] (**) Option "xkb_variant" "azerty,"
[    63.688] (II) event1  - Sleep Button: is tagged by udev as: Keyboard
[    63.688] (II) event1  - Sleep Button: device is a keyboard
[    63.689] (II) config/udev: Adding input device Logitech USB Optical Mouse (/dev/input/event5)
[    63.689] (**) Logitech USB Optical Mouse: Applying InputClass "libinput pointer catchall"
[    63.689] (II) Using input driver 'libinput' for 'Logitech USB Optical Mouse'
[    63.690] (II) systemd-logind: got fd for /dev/input/event5 13:69 fd 30 paused 0
[    63.690] (**) Logitech USB Optical Mouse: always reports core events
[    63.690] (**) Option "Device" "/dev/input/event5"
[    63.690] (**) Option "_source" "server/udev"
[    63.692] (II) event5  - Logitech USB Optical Mouse: is tagged by udev as: Mouse
[    63.692] (II) event5  - Logitech USB Optical Mouse: device is a pointer
[    63.692] (II) event5  - Logitech USB Optical Mouse: device removed
[    63.692] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1:1.0/0003:046D:C077.0001/input/input9/event5"
[    63.692] (II) XINPUT: Adding extended input device "Logitech USB Optical Mouse" (type: MOUSE, id 11)
[    63.692] (**) Option "AccelerationScheme" "none"
[    63.692] (**) Logitech USB Optical Mouse: (accel) selected scheme none/0
[    63.692] (**) Logitech USB Optical Mouse: (accel) acceleration factor: 2.000
[    63.692] (**) Logitech USB Optical Mouse: (accel) acceleration threshold: 4
[    63.693] (II) event5  - Logitech USB Optical Mouse: is tagged by udev as: Mouse
[    63.694] (II) event5  - Logitech USB Optical Mouse: device is a pointer
[    63.694] (II) config/udev: Adding input device Logitech USB Optical Mouse (/dev/input/mouse0)
[    63.694] (II) No input driver specified, ignoring this device.
[    63.694] (II) This device may have been added with another device file.
[    63.695] (II) config/udev: Adding input device Logitech USB Keyboard (/dev/input/event6)
[    63.695] (**) Logitech USB Keyboard: Applying InputClass "libinput keyboard catchall"
[    63.695] (**) Logitech USB Keyboard: Applying InputClass "system-keyboard"
[    63.695] (II) Using input driver 'libinput' for 'Logitech USB Keyboard'
[    63.696] (II) systemd-logind: got fd for /dev/input/event6 13:70 fd 31 paused 0
[    63.696] (**) Logitech USB Keyboard: always reports core events
[    63.696] (**) Option "Device" "/dev/input/event6"
[    63.696] (**) Option "_source" "server/udev"
[    63.697] (II) event6  - Logitech USB Keyboard: is tagged by udev as: Keyboard
[    63.697] (II) event6  - Logitech USB Keyboard: device is a keyboard
[    63.697] (II) event6  - Logitech USB Keyboard: device removed
[    63.697] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.0/0003:046D:C31C.0002/input/input10/event6"
[    63.697] (II) XINPUT: Adding extended input device "Logitech USB Keyboard" (type: KEYBOARD, id 12)
[    63.697] (**) Option "xkb_layout" "fr,gb"
[    63.697] (**) Option "xkb_variant" "azerty,"
[    63.699] (II) event6  - Logitech USB Keyboard: is tagged by udev as: Keyboard
[    63.699] (II) event6  - Logitech USB Keyboard: device is a keyboard
[    63.700] (II) config/udev: Adding input device Logitech USB Keyboard Consumer Control (/dev/input/event7)
[    63.700] (**) Logitech USB Keyboard Consumer Control: Applying InputClass "libinput keyboard catchall"
[    63.700] (**) Logitech USB Keyboard Consumer Control: Applying InputClass "system-keyboard"
[    63.700] (II) Using input driver 'libinput' for 'Logitech USB Keyboard Consumer Control'
[    63.701] (II) systemd-logind: got fd for /dev/input/event7 13:71 fd 32 paused 0
[    63.701] (**) Logitech USB Keyboard Consumer Control: always reports core events
[    63.701] (**) Option "Device" "/dev/input/event7"
[    63.701] (**) Option "_source" "server/udev"
[    63.703] (II) event7  - Logitech USB Keyboard Consumer Control: is tagged by udev as: Keyboard
[    63.703] (II) event7  - Logitech USB Keyboard Consumer Control: device is a keyboard
[    63.703] (II) event7  - Logitech USB Keyboard Consumer Control: device removed
[    63.703] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.1/0003:046D:C31C.0003/input/input11/event7"
[    63.703] (II) XINPUT: Adding extended input device "Logitech USB Keyboard Consumer Control" (type: KEYBOARD, id 13)
[    63.703] (**) Option "xkb_layout" "fr,gb"
[    63.703] (**) Option "xkb_variant" "azerty,"
[    63.705] (II) event7  - Logitech USB Keyboard Consumer Control: is tagged by udev as: Keyboard
[    63.705] (II) event7  - Logitech USB Keyboard Consumer Control: device is a keyboard
[    63.706] (II) config/udev: Adding input device Logitech USB Keyboard System Control (/dev/input/event8)
[    63.706] (**) Logitech USB Keyboard System Control: Applying InputClass "libinput keyboard catchall"
[    63.706] (**) Logitech USB Keyboard System Control: Applying InputClass "system-keyboard"
[    63.706] (II) Using input driver 'libinput' for 'Logitech USB Keyboard System Control'
[    63.707] (II) systemd-logind: got fd for /dev/input/event8 13:72 fd 33 paused 0
[    63.707] (**) Logitech USB Keyboard System Control: always reports core events
[    63.707] (**) Option "Device" "/dev/input/event8"
[    63.707] (**) Option "_source" "server/udev"
[    63.709] (II) event8  - Logitech USB Keyboard System Control: is tagged by udev as: Keyboard
[    63.709] (II) event8  - Logitech USB Keyboard System Control: device is a keyboard
[    63.709] (II) event8  - Logitech USB Keyboard System Control: device removed
[    63.709] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.1/0003:046D:C31C.0003/input/input12/event8"
[    63.709] (II) XINPUT: Adding extended input device "Logitech USB Keyboard System Control" (type: KEYBOARD, id 14)
[    63.709] (**) Option "xkb_layout" "fr,gb"
[    63.709] (**) Option "xkb_variant" "azerty,"
[    63.711] (II) event8  - Logitech USB Keyboard System Control: is tagged by udev as: Keyboard
[    63.711] (II) event8  - Logitech USB Keyboard System Control: device is a keyboard
[    63.711] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event12)
[    63.711] (II) No input driver specified, ignoring this device.
[    63.711] (II) This device may have been added with another device file.
[    63.712] (II) config/udev: Adding input device HDA Intel PCH Mic (/dev/input/event13)
[    63.712] (II) No input driver specified, ignoring this device.
[    63.712] (II) This device may have been added with another device file.
[    63.712] (II) config/udev: Adding input device HDA Intel PCH Headphone (/dev/input/event14)
[    63.712] (II) No input driver specified, ignoring this device.
[    63.712] (II) This device may have been added with another device file.
[    63.713] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event15)
[    63.713] (II) No input driver specified, ignoring this device.
[    63.713] (II) This device may have been added with another device file.
[    63.713] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=7 (/dev/input/event16)
[    63.713] (II) No input driver specified, ignoring this device.
[    63.713] (II) This device may have been added with another device file.
[    63.713] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=8 (/dev/input/event17)
[    63.713] (II) No input driver specified, ignoring this device.
[    63.713] (II) This device may have been added with another device file.
[    63.714] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=9 (/dev/input/event18)
[    63.714] (II) No input driver specified, ignoring this device.
[    63.714] (II) This device may have been added with another device file.
[    63.714] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=10 (/dev/input/event19)
[    63.714] (II) No input driver specified, ignoring this device.
[    63.714] (II) This device may have been added with another device file.
[    63.715] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event4)
[    63.715] (**) AT Translated Set 2 keyboard: Applying InputClass "libinput keyboard catchall"
[    63.715] (**) AT Translated Set 2 keyboard: Applying InputClass "system-keyboard"
[    63.715] (II) Using input driver 'libinput' for 'AT Translated Set 2 keyboard'
[    63.716] (II) systemd-logind: got fd for /dev/input/event4 13:68 fd 34 paused 0
[    63.716] (**) AT Translated Set 2 keyboard: always reports core events
[    63.716] (**) Option "Device" "/dev/input/event4"
[    63.716] (**) Option "_source" "server/udev"
[    63.717] (II) event4  - AT Translated Set 2 keyboard: is tagged by udev as: Keyboard
[    63.717] (II) event4  - AT Translated Set 2 keyboard: device is a keyboard
[    63.718] (II) event4  - AT Translated Set 2 keyboard: device removed
[    63.718] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input4/event4"
[    63.718] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 15)
[    63.718] (**) Option "xkb_layout" "fr,gb"
[    63.718] (**) Option "xkb_variant" "azerty,"
[    63.719] (II) event4  - AT Translated Set 2 keyboard: is tagged by udev as: Keyboard
[    63.719] (II) event4  - AT Translated Set 2 keyboard: device is a keyboard
[    63.721] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/event20)
[    63.721] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "libinput touchpad catchall"
[    63.721] (II) Using input driver 'libinput' for 'SynPS/2 Synaptics TouchPad'
[    63.721] (II) systemd-logind: got fd for /dev/input/event20 13:84 fd 35 paused 0
[    63.721] (**) SynPS/2 Synaptics TouchPad: always reports core events
[    63.721] (**) Option "Device" "/dev/input/event20"
[    63.721] (**) Option "_source" "server/udev"
[    63.723] (II) event20 - SynPS/2 Synaptics TouchPad: is tagged by udev as: Touchpad
[    63.724] (II) event20 - SynPS/2 Synaptics TouchPad: device is a touchpad
[    63.724] (II) event20 - SynPS/2 Synaptics TouchPad: device removed
[    63.724] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio2/input/input15/event20"
[    63.724] (II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD, id 16)
[    63.724] (**) Option "AccelerationScheme" "none"
[    63.724] (**) SynPS/2 Synaptics TouchPad: (accel) selected scheme none/0
[    63.724] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration factor: 2.000
[    63.724] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration threshold: 4
[    63.725] (II) event20 - SynPS/2 Synaptics TouchPad: is tagged by udev as: Touchpad
[    63.726] (II) event20 - SynPS/2 Synaptics TouchPad: device is a touchpad
[    63.727] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/mouse1)
[    63.727] (II) No input driver specified, ignoring this device.
[    63.727] (II) This device may have been added with another device file.
[    63.727] (II) config/udev: Adding input device PC Speaker (/dev/input/event9)
[    63.727] (II) No input driver specified, ignoring this device.
[    63.727] (II) This device may have been added with another device file.
[   121.200] (**) Option "fd" "23"
[   121.200] (II) event3  - Power Button: device removed
[   121.201] (**) Option "fd" "26"
[   121.201] (II) event10 - Video Bus: device removed
[   121.202] (**) Option "fd" "27"
[   121.202] (II) event11 - Video Bus: device removed
[   121.202] (**) Option "fd" "28"
[   121.202] (II) event0  - Power Button: device removed
[   121.202] (**) Option "fd" "29"
[   121.202] (II) event1  - Sleep Button: device removed
[   121.203] (**) Option "fd" "30"
[   121.203] (II) event5  - Logitech USB Optical Mouse: device removed
[   121.203] (**) Option "fd" "31"
[   121.203] (II) event6  - Logitech USB Keyboard: device removed
[   121.203] (**) Option "fd" "32"
[   121.203] (II) event7  - Logitech USB Keyboard Consumer Control: device removed
[   121.203] (**) Option "fd" "33"
[   121.203] (II) event8  - Logitech USB Keyboard System Control: device removed
[   121.203] (**) Option "fd" "34"
[   121.203] (II) event4  - AT Translated Set 2 keyboard: device removed
[   121.204] (**) Option "fd" "35"
[   121.204] (II) event20 - SynPS/2 Synaptics TouchPad: device removed
[   121.273] (II) systemd-logind: got pause for 13:67
[   121.273] (II) systemd-logind: got pause for 13:72
[   121.273] (II) systemd-logind: got pause for 13:74
[   121.273] (II) systemd-logind: got pause for 13:75
[   121.273] (II) systemd-logind: got pause for 13:64
[   121.273] (II) systemd-logind: got pause for 13:70
[   121.273] (II) systemd-logind: got pause for 13:71
[   121.273] (II) systemd-logind: got pause for 13:65
[   121.273] (II) systemd-logind: got pause for 13:68
[   121.273] (II) systemd-logind: got pause for 13:84
[   121.273] (II) systemd-logind: got pause for 13:69
[   121.273] (II) systemd-logind: got pause for 226:0
[   131.730] (II) systemd-logind: got resume for 13:67
[   131.757] (II) systemd-logind: got resume for 13:72
[   131.784] (II) systemd-logind: got resume for 13:74
[   131.810] (II) systemd-logind: got resume for 13:75
[   131.837] (II) systemd-logind: got resume for 13:64
[   131.864] (II) systemd-logind: got resume for 13:70
[   131.890] (II) systemd-logind: got resume for 13:71
[   131.917] (II) systemd-logind: got resume for 13:65
[   131.943] (II) systemd-logind: got resume for 13:68
[   131.970] (II) systemd-logind: got resume for 13:84
[   131.998] (II) systemd-logind: got resume for 13:69
[   131.998] (II) systemd-logind: got resume for 226:0
[   132.015] (II) NVIDIA(0): Setting mode "NULL"
[   132.016] (II) NVIDIA(0): ACPI: failed to connect to the ACPI event daemon; the daemon
[   132.016] (II) NVIDIA(0):     may not be running or the "AcpidSocketPath" X
[   132.016] (II) NVIDIA(0):     configuration option may not be set correctly.  When the
[   132.016] (II) NVIDIA(0):     ACPI event daemon is available, the NVIDIA X driver will
[   132.016] (II) NVIDIA(0):     try to use it to receive ACPI event notifications.  For
[   132.016] (II) NVIDIA(0):     details, please see the "ConnectToAcpid" and
[   132.016] (II) NVIDIA(0):     "AcpidSocketPath" X configuration options in Appendix B: X
[   132.016] (II) NVIDIA(0):     Config Options in the README.
[   132.020] (II) event3  - Power Button: is tagged by udev as: Keyboard
[   132.020] (II) event3  - Power Button: device is a keyboard
[   132.022] (II) event10 - Video Bus: is tagged by udev as: Keyboard
[   132.022] (II) event10 - Video Bus: device is a keyboard
[   132.023] (II) event11 - Video Bus: is tagged by udev as: Keyboard
[   132.023] (II) event11 - Video Bus: device is a keyboard
[   132.025] (II) event0  - Power Button: is tagged by udev as: Keyboard
[   132.025] (II) event0  - Power Button: device is a keyboard
[   132.026] (II) event1  - Sleep Button: is tagged by udev as: Keyboard
[   132.026] (II) event1  - Sleep Button: device is a keyboard
[   132.028] (II) event5  - Logitech USB Optical Mouse: is tagged by udev as: Mouse
[   132.028] (II) event5  - Logitech USB Optical Mouse: device is a pointer
[   132.029] (II) event6  - Logitech USB Keyboard: is tagged by udev as: Keyboard
[   132.029] (II) event6  - Logitech USB Keyboard: device is a keyboard
[   132.031] (II) event7  - Logitech USB Keyboard Consumer Control: is tagged by udev as: Keyboard
[   132.031] (II) event7  - Logitech USB Keyboard Consumer Control: device is a keyboard
[   132.032] (II) event8  - Logitech USB Keyboard System Control: is tagged by udev as: Keyboard
[   132.032] (II) event8  - Logitech USB Keyboard System Control: device is a keyboard
[   132.034] (II) event4  - AT Translated Set 2 keyboard: is tagged by udev as: Keyboard
[   132.034] (II) event4  - AT Translated Set 2 keyboard: device is a keyboard
[   132.036] (II) event20 - SynPS/2 Synaptics TouchPad: is tagged by udev as: Touchpad
[   132.037] (II) event20 - SynPS/2 Synaptics TouchPad: device is a touchpad
[   135.110] (**) Option "fd" "20"
[   135.110] (II) event3  - Power Button: device removed
[   135.112] (**) Option "fd" "26"
[   135.113] (II) event10 - Video Bus: device removed
[   135.114] (**) Option "fd" "27"
[   135.114] (II) event11 - Video Bus: device removed
[   135.114] (**) Option "fd" "28"
[   135.114] (II) event0  - Power Button: device removed
[   135.115] (**) Option "fd" "31"
[   135.115] (II) event1  - Sleep Button: device removed
[   135.115] (**) Option "fd" "35"
[   135.115] (II) event5  - Logitech USB Optical Mouse: device removed
[   135.116] (**) Option "fd" "29"
[   135.116] (II) event6  - Logitech USB Keyboard: device removed
[   135.116] (**) Option "fd" "30"
[   135.116] (II) event7  - Logitech USB Keyboard Consumer Control: device removed
[   135.117] (**) Option "fd" "23"
[   135.117] (II) event8  - Logitech USB Keyboard System Control: device removed
[   135.117] (**) Option "fd" "32"
[   135.117] (II) event4  - AT Translated Set 2 keyboard: device removed
[   135.118] (**) Option "fd" "33"
[   135.118] (II) event20 - SynPS/2 Synaptics TouchPad: device removed
[   135.128] (II) systemd-logind: got pause for 13:67
[   135.128] (II) systemd-logind: got pause for 13:72
[   135.128] (II) systemd-logind: got pause for 13:74
[   135.128] (II) systemd-logind: got pause for 13:75
[   135.128] (II) systemd-logind: got pause for 13:64
[   135.128] (II) systemd-logind: got pause for 13:70
[   135.128] (II) systemd-logind: got pause for 13:71
[   135.128] (II) systemd-logind: got pause for 13:65
[   135.128] (II) systemd-logind: got pause for 13:68
[   135.128] (II) systemd-logind: got pause for 13:84
[   135.128] (II) systemd-logind: got pause for 13:69
[   135.128] (II) systemd-logind: got pause for 226:0
[   149.927] (II) systemd-logind: got resume for 13:67
[   149.944] (II) systemd-logind: got resume for 13:72
[   149.975] (II) systemd-logind: got resume for 13:74
[   150.010] (II) systemd-logind: got resume for 13:75
[   150.037] (II) systemd-logind: got resume for 13:64
[   150.052] (II) systemd-logind: got resume for 13:70
[   150.077] (II) systemd-logind: got resume for 13:71
[   150.104] (II) systemd-logind: got resume for 13:65
[   150.130] (II) systemd-logind: got resume for 13:68
[   150.157] (II) systemd-logind: got resume for 13:84
[   150.197] (II) systemd-logind: got resume for 13:69
[   150.197] (II) systemd-logind: got resume for 226:0
[   150.214] (II) NVIDIA(0): Setting mode "NULL"
[   150.215] (II) NVIDIA(0): ACPI: failed to connect to the ACPI event daemon; the daemon
[   150.215] (II) NVIDIA(0):     may not be running or the "AcpidSocketPath" X
[   150.215] (II) NVIDIA(0):     configuration option may not be set correctly.  When the
[   150.215] (II) NVIDIA(0):     ACPI event daemon is available, the NVIDIA X driver will
[   150.215] (II) NVIDIA(0):     try to use it to receive ACPI event notifications.  For
[   150.215] (II) NVIDIA(0):     details, please see the "ConnectToAcpid" and
[   150.215] (II) NVIDIA(0):     "AcpidSocketPath" X configuration options in Appendix B: X
[   150.215] (II) NVIDIA(0):     Config Options in the README.
[   150.219] (II) event3  - Power Button: is tagged by udev as: Keyboard
[   150.220] (II) event3  - Power Button: device is a keyboard
[   150.221] (II) event10 - Video Bus: is tagged by udev as: Keyboard
[   150.221] (II) event10 - Video Bus: device is a keyboard
[   150.223] (II) event11 - Video Bus: is tagged by udev as: Keyboard
[   150.223] (II) event11 - Video Bus: device is a keyboard
[   150.224] (II) event0  - Power Button: is tagged by udev as: Keyboard
[   150.224] (II) event0  - Power Button: device is a keyboard
[   150.225] (II) event1  - Sleep Button: is tagged by udev as: Keyboard
[   150.225] (II) event1  - Sleep Button: device is a keyboard
[   150.227] (II) event5  - Logitech USB Optical Mouse: is tagged by udev as: Mouse
[   150.227] (II) event5  - Logitech USB Optical Mouse: device is a pointer
[   150.228] (II) event6  - Logitech USB Keyboard: is tagged by udev as: Keyboard
[   150.228] (II) event6  - Logitech USB Keyboard: device is a keyboard
[   150.230] (II) event7  - Logitech USB Keyboard Consumer Control: is tagged by udev as: Keyboard
[   150.230] (II) event7  - Logitech USB Keyboard Consumer Control: device is a keyboard
[   150.231] (II) event8  - Logitech USB Keyboard System Control: is tagged by udev as: Keyboard
[   150.232] (II) event8  - Logitech USB Keyboard System Control: device is a keyboard
[   150.233] (II) event4  - AT Translated Set 2 keyboard: is tagged by udev as: Keyboard
[   150.233] (II) event4  - AT Translated Set 2 keyboard: device is a keyboard
[   150.235] (II) event20 - SynPS/2 Synaptics TouchPad: is tagged by udev as: Touchpad
[   150.236] (II) event20 - SynPS/2 Synaptics TouchPad: device is a touchpad
[   153.934] (**) Option "fd" "23"
[   153.935] (II) event3  - Power Button: device removed
[   153.937] (**) Option "fd" "27"
[   153.937] (II) event10 - Video Bus: device removed
[   153.938] (**) Option "fd" "28"
[   153.938] (II) event11 - Video Bus: device removed
[   153.938] (**) Option "fd" "29"
[   153.938] (II) event0  - Power Button: device removed
[   153.939] (**) Option "fd" "32"
[   153.939] (II) event1  - Sleep Button: device removed
[   153.939] (**) Option "fd" "55"
[   153.940] (II) event5  - Logitech USB Optical Mouse: device removed
[   153.941] (**) Option "fd" "30"
[   153.941] (II) event6  - Logitech USB Keyboard: device removed
[   153.941] (**) Option "fd" "31"
[   153.941] (II) event7  - Logitech USB Keyboard Consumer Control: device removed
[   153.942] (**) Option "fd" "26"
[   153.942] (II) event8  - Logitech USB Keyboard System Control: device removed
[   153.942] (**) Option "fd" "33"
[   153.942] (II) event4  - AT Translated Set 2 keyboard: device removed
[   153.943] (**) Option "fd" "34"
[   153.943] (II) event20 - SynPS/2 Synaptics TouchPad: device removed
[   153.990] (II) systemd-logind: got pause for 13:67
[   153.990] (II) systemd-logind: got pause for 13:72
[   153.990] (II) systemd-logind: got pause for 13:74
[   153.990] (II) systemd-logind: got pause for 13:75
[   153.990] (II) systemd-logind: got pause for 13:64
[   153.990] (II) systemd-logind: got pause for 13:70
[   153.991] (II) systemd-logind: got pause for 13:71
[   153.991] (II) systemd-logind: got pause for 13:65
[   153.991] (II) systemd-logind: got pause for 13:68
[   153.991] (II) systemd-logind: got pause for 13:84
[   153.991] (II) systemd-logind: got pause for 13:69
[   153.991] (II) systemd-logind: got pause for 226:0
[   192.224] (II) systemd-logind: got resume for 13:67
[   192.250] (II) systemd-logind: got resume for 13:72
[   192.274] (II) systemd-logind: got resume for 13:74
[   192.310] (II) systemd-logind: got resume for 13:75
[   192.344] (II) systemd-logind: got resume for 13:64
[   192.370] (II) systemd-logind: got resume for 13:70
[   192.397] (II) systemd-logind: got resume for 13:71
[   192.424] (II) systemd-logind: got resume for 13:65
[   192.450] (II) systemd-logind: got resume for 13:68
[   192.477] (II) systemd-logind: got resume for 13:84
[   192.504] (II) systemd-logind: got resume for 13:69
[   192.504] (II) systemd-logind: got resume for 226:0
[   192.539] (II) NVIDIA(0): Setting mode "NULL"
[   192.540] (II) NVIDIA(0): ACPI: failed to connect to the ACPI event daemon; the daemon
[   192.540] (II) NVIDIA(0):     may not be running or the "AcpidSocketPath" X
[   192.540] (II) NVIDIA(0):     configuration option may not be set correctly.  When the
[   192.540] (II) NVIDIA(0):     ACPI event daemon is available, the NVIDIA X driver will
[   192.540] (II) NVIDIA(0):     try to use it to receive ACPI event notifications.  For
[   192.540] (II) NVIDIA(0):     details, please see the "ConnectToAcpid" and
[   192.540] (II) NVIDIA(0):     "AcpidSocketPath" X configuration options in Appendix B: X
[   192.540] (II) NVIDIA(0):     Config Options in the README.
[   192.547] (II) event3  - Power Button: is tagged by udev as: Keyboard
[   192.547] (II) event3  - Power Button: device is a keyboard
[   192.549] (II) event10 - Video Bus: is tagged by udev as: Keyboard
[   192.549] (II) event10 - Video Bus: device is a keyboard
[   192.550] (II) event11 - Video Bus: is tagged by udev as: Keyboard
[   192.550] (II) event11 - Video Bus: device is a keyboard
[   192.552] (II) event0  - Power Button: is tagged by udev as: Keyboard
[   192.552] (II) event0  - Power Button: device is a keyboard
[   192.553] (II) event1  - Sleep Button: is tagged by udev as: Keyboard
[   192.553] (II) event1  - Sleep Button: device is a keyboard
[   192.554] (II) event5  - Logitech USB Optical Mouse: is tagged by udev as: Mouse
[   192.554] (II) event5  - Logitech USB Optical Mouse: device is a pointer
[   192.556] (II) event6  - Logitech USB Keyboard: is tagged by udev as: Keyboard
[   192.556] (II) event6  - Logitech USB Keyboard: device is a keyboard
[   192.558] (II) event7  - Logitech USB Keyboard Consumer Control: is tagged by udev as: Keyboard
[   192.558] (II) event7  - Logitech USB Keyboard Consumer Control: device is a keyboard
[   192.559] (II) event8  - Logitech USB Keyboard System Control: is tagged by udev as: Keyboard
[   192.559] (II) event8  - Logitech USB Keyboard System Control: device is a keyboard
[   192.561] (II) event4  - AT Translated Set 2 keyboard: is tagged by udev as: Keyboard
[   192.561] (II) event4  - AT Translated Set 2 keyboard: device is a keyboard
[   192.563] (II) event20 - SynPS/2 Synaptics TouchPad: is tagged by udev as: Touchpad
[   192.564] (II) event20 - SynPS/2 Synaptics TouchPad: device is a touchpad
[   194.428] (**) Option "fd" "26"
[   194.428] (II) event3  - Power Button: device removed
[   194.431] (**) Option "fd" "28"
[   194.431] (II) event10 - Video Bus: device removed
[   194.432] (**) Option "fd" "29"
[   194.432] (II) event11 - Video Bus: device removed
[   194.433] (**) Option "fd" "30"
[   194.433] (II) event0  - Power Button: device removed
[   194.433] (**) Option "fd" "33"
[   194.433] (II) event1  - Sleep Button: device removed
[   194.434] (**) Option "fd" "56"
[   194.434] (II) event5  - Logitech USB Optical Mouse: device removed
[   194.435] (**) Option "fd" "31"
[   194.435] (II) event6  - Logitech USB Keyboard: device removed
[   194.435] (**) Option "fd" "32"
[   194.435] (II) event7  - Logitech USB Keyboard Consumer Control: device removed
[   194.436] (**) Option "fd" "27"
[   194.436] (II) event8  - Logitech USB Keyboard System Control: device removed
[   194.436] (**) Option "fd" "34"
[   194.436] (II) event4  - AT Translated Set 2 keyboard: device removed
[   194.437] (**) Option "fd" "35"
[   194.437] (II) event20 - SynPS/2 Synaptics TouchPad: device removed
[   194.496] (II) systemd-logind: got pause for 13:67
[   194.496] (II) systemd-logind: got pause for 13:72
[   194.496] (II) systemd-logind: got pause for 13:74
[   194.496] (II) systemd-logind: got pause for 13:75
[   194.496] (II) systemd-logind: got pause for 13:64
[   194.496] (II) systemd-logind: got pause for 13:70
[   194.496] (II) systemd-logind: got pause for 13:71
[   194.496] (II) systemd-logind: got pause for 13:65
[   194.496] (II) systemd-logind: got pause for 13:68
[   194.496] (II) systemd-logind: got pause for 13:84
[   194.496] (II) systemd-logind: got pause for 13:69
[   194.496] (II) systemd-logind: got pause for 226:0
[   209.549] (II) UnloadModule: "libinput"
[   209.549] (II) systemd-logind: releasing fd for 13:84
[   209.697] (II) UnloadModule: "libinput"
[   209.697] (II) systemd-logind: releasing fd for 13:68
[   209.720] (II) UnloadModule: "libinput"
[   209.720] (II) systemd-logind: releasing fd for 13:72
[   209.743] (II) UnloadModule: "libinput"
[   209.743] (II) systemd-logind: releasing fd for 13:71
[   209.770] (II) UnloadModule: "libinput"
[   209.770] (II) systemd-logind: releasing fd for 13:70
[   209.800] (II) UnloadModule: "libinput"
[   209.800] (II) systemd-logind: releasing fd for 13:69
[   209.810] (II) UnloadModule: "libinput"
[   209.810] (II) systemd-logind: releasing fd for 13:65
[   209.823] (II) UnloadModule: "libinput"
[   209.823] (II) systemd-logind: releasing fd for 13:64
[   209.848] (II) UnloadModule: "libinput"
[   209.848] (II) systemd-logind: releasing fd for 13:75
[   209.873] (II) UnloadModule: "libinput"
[   209.873] (II) systemd-logind: releasing fd for 13:74
[   209.887] (II) UnloadModule: "libinput"
[   209.887] (II) systemd-logind: releasing fd for 13:67
[   209.929] (II) NVIDIA(GPU-0): Deleting GPU-0
[   209.930] (WW) xf86CloseConsole: KDSETMODE failed: Input/output error
[   209.930] (WW) xf86CloseConsole: VT_GETMODE failed: Input/output error
[   209.930] (WW) xf86CloseConsole: VT_ACTIVATE failed: Input/output error
[   209.931] (II) Server terminated successfully (0). Closing log file.

Why is it trying to load "glxserver_nvidia"? Do I really need that? Gnome seems just fine without it. If I install and load this, isn't it going to break my current configuration (I'm using bumblebee)?

Gnome is not using xorg. But there appears to be a xorg.conf file already (which I modified as mentioned in my first message).

# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig:  version 396.54  (buildmeister@swio-display-x64-rhel04-14)  Wed Aug 15 00:22:27 PDT 2018

Section "ServerLayout"
    Identifier     "Layout0"
    Screen      0  "Screen0"
    InputDevice    "Keyboard0" "CoreKeyboard"
    InputDevice    "Mouse0" "CorePointer"
EndSection

Section "Files"
EndSection

Section "InputDevice"
    # generated from default
    Identifier     "Mouse0"
    Driver         "mouse"
    Option         "Protocol" "auto"
    Option         "Device" "/dev/psaux"
    Option         "Emulate3Buttons" "no"
    Option         "ZAxisMapping" "4 5"
EndSection

Section "InputDevice"
    # generated from default
    Identifier     "Keyboard0"
    Driver         "kbd"
EndSection

Section "Monitor"
    Identifier     "Monitor0"
    VendorName     "Unknown"
    ModelName      "Unknown"
    HorizSync       28.0 - 33.0
    VertRefresh     43.0 - 72.0
    Option         "DPMS"
EndSection

Section "Device"
    Identifier     "Device0"
    Driver         "nvidia"
    VendorName     "NVIDIA Corporation"
    BusID          "PCI:1:0:0"
EndSection

Section "Screen"
    Identifier     "Screen0"
    Device         "Device0"
    Monitor        "Monitor0"
    DefaultDepth    24
    SubSection     "Display"
        Depth       24
    EndSubSection
EndSection

Last edited by charlie (2020-04-21 17:24:33)

Offline

#4 2020-04-21 17:35:57

Slithery
Administrator
From: Norfolk, UK
Registered: 2013-12-01
Posts: 5,776

Re: Installing Xfce (with nvidia)

charlie wrote:

But there appears to be a xorg.conf file already (which I modified as mentioned in my first message).

Why was it there in the first place? Using nvidia-xconfig is well known to create broken configs.

No, it didn't "fix" anything. It just shifted the brokeness one space to the right. - jasonwryan
Closing -- for deletion; Banning -- for muppetry. - jasonwryan

aur - dotfiles

Offline

#5 2020-04-21 17:43:47

charlie
Member
Registered: 2013-09-18
Posts: 57

Re: Installing Xfce (with nvidia)

Why was it there in the first place?

I have no idea. Maybe because gnome used to work with x at some point in the history of the system.

Using nvidia-xconfig is well known to create broken configs.

I've seen this kind of remarks indeed. This doesnt tell me what to do to improve the configs. I've modified the xorg.conf, following some advice on some forum (this is what I was mentioning above).

Last edited by charlie (2020-04-21 17:44:51)

Offline

#6 2020-04-21 17:44:00

Trilby
Inspector Parrot
Registered: 2011-11-29
Posts: 30,520
Website

Re: Installing Xfce (with nvidia)

EDIT: this was cross posted with the above two post.

charlie wrote:

I'm happy to post my xorg.log but my question is more about, how do I figure this out on my own.

Ah .. what?  So you want us to ignore your post?

To figure this out, you need to check the logs and identify the problem then fix it.  If you can do this yourself, wonderful.  If you want help, though, we'll need the informaiton.

charlie wrote:

... Gnome seems just fine without it.... Gnome is not using xorg.

How do you know gnome is fine without it?  And even it if is, so what, if gnome is not running on Xorg, there's going to be a lot of things different.

charlie wrote:

But there appears to be a xorg.conf file already

I'm not familiar with hybrid systems or bumblebee, but it seems generally ill advised to use the nvidia-xconfig generated xorg.conf.  Others with the relevant experience can comment on this further.

Last edited by Trilby (2020-04-21 17:44:35)

"UNIX is simple and coherent" - Dennis Ritchie; "GNU's Not Unix" - Richard Stallman

Offline

#7 2020-04-21 17:47:27

charlie
Member
Registered: 2013-09-18
Posts: 57

Re: Installing Xfce (with nvidia)

So you want us to ignore your post?

No please tell me what's wrong if you can.

I say Gnome seems to work fine, because I can use it normally. Maybe in the back something is broken but I dont see it.

And even it if is, so what, if gnome is not running on Xorg, there's going to be a lot of things different

That's the kind of things I wish I could understand/figure out.

Last edited by charlie (2020-04-21 17:51:41)

Offline

#8 2020-04-21 17:55:39

loqs
Member
Registered: 2014-03-06
Posts: 19,078

Re: Installing Xfce (with nvidia)

I would start by disabling the Xorg.conf.  You mention selecting the desktop environment,  is that from a display manage?  If so which one?
If it is GDM are you certain gnome is not started under Wayland instead of X?

Last edited by loqs (2020-04-21 17:56:07)

Offline

#9 2020-04-21 18:02:22

charlie
Member
Registered: 2013-09-18
Posts: 57

Re: Installing Xfce (with nvidia)

Does that show it's using GDM:

$ systemctl status gdm.service
● gdm.service - GNOME Display Manager
     Loaded: loaded (/usr/lib/systemd/system/gdm.service; enabled; vendor preset: disabled)
     Active: active (running) since Tue 2020-04-21 11:36:30 BST; 7h ago
   Main PID: 451 (gdm)
      Tasks: 3 (limit: 9378)
     Memory: 6.6M
     CGroup: /system.slice/gdm.service
             └─451 /usr/bin/gdm

?

As for Wayland:

$ loginctl show-session $(awk '/tty/ {print $1}' <(loginctl)) -p Type | awk -F= '{print $2}'
wayland

Last edited by charlie (2020-04-21 18:03:42)

Offline

Pages: 1

Board footer

Powered by FluxBB