Arch Linux

Captain Athelas

Member

Registered: 2020-05-15

Posts: 42

Checking GPU temperature

Hello, I have a Ryzen 3600 CPU and 5700XT GPU. I would like to check the GPU temps, but the output sensors is just this:

nct6795-isa-0a20
Adapter: ISA adapter
Vcore:                 992.00 mV (min =  +0.00 V, max =  +1.74 V)
in1:                     1.02 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
AVCC:                    3.33 V  (min =  +2.98 V, max =  +3.63 V)
+3.3V:                   3.38 V  (min =  +2.98 V, max =  +3.63 V)
in4:                     1.02 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in5:                   152.00 mV (min =  +0.00 V, max =  +0.00 V)  ALARM
in6:                   768.00 mV (min =  +0.00 V, max =  +0.00 V)  ALARM
3VSB:                    3.33 V  (min =  +2.98 V, max =  +3.63 V)
Vbat:                    3.28 V  (min =  +2.70 V, max =  +3.63 V)
in9:                     1.83 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in10:                    0.00 V  (min =  +0.00 V, max =  +0.00 V)
in11:                  704.00 mV (min =  +0.00 V, max =  +0.00 V)  ALARM
in12:                    1.02 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in13:                  680.00 mV (min =  +0.00 V, max =  +0.00 V)  ALARM
in14:                    1.54 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
fan1:                     0 RPM  (min =    0 RPM)
fan2:                   865 RPM  (min =    0 RPM)
fan3:                   665 RPM  (min =    0 RPM)
fan4:                     0 RPM  (min =    0 RPM)
fan5:                   599 RPM  (min =    0 RPM)
fan6:                   610 RPM  (min =    0 RPM)
SYSTIN:                 +33.0°C  (high =  +0.0°C, hyst =  +0.0°C)  ALARM  sensor = CPU diode
CPUTIN:                 +30.0°C  (high = +110.0°C, hyst = +90.0°C)  sensor = thermistor
AUXTIN0:                +38.5°C  (high = +110.0°C, hyst = +90.0°C)  sensor = thermistor
AUXTIN1:               -128.0°C    sensor = thermistor
AUXTIN2:                +42.0°C    sensor = thermistor
AUXTIN3:                 -2.0°C    sensor = thermistor
SMBUSMASTER 0:          +36.0°C  
PCH_CHIP_CPU_MAX_TEMP:   +0.0°C  
PCH_CHIP_TEMP:           +0.0°C  
PCH_CPU_TEMP:            +0.0°C  
intrusion0:            ALARM
intrusion1:            ALARM
beep_enable:           disabled

k10temp-pci-00c3
Adapter: PCI adapter
Vcore:       988.00 mV 
Vsoc:        1000.00 mV 
Tdie:         +35.8°C  
Tctl:         +35.8°C  
Tccd1:        +31.0°C  
Icore:         6.00 A  
Isoc:          6.25 A  

nvme-pci-0100
Adapter: PCI adapter
Composite:    +42.9°C  (low  = -273.1°C, high = +69.8°C)
                       (crit = +79.8°C)
Sensor 1:     +44.9°C  (low  = -273.1°C, high = +65261.8°C)
Sensor 2:     +40.9°C  (low  = -273.1°C, high = +65261.8°C)
Sensor 5:     +80.8°C  (low  = -273.1°C, high = +65261.8°C)

amdgpu-pci-2900
Adapter: PCI adapter
vddgfx:      725.00 mV 
fan1:         850 RPM  (min =    0 RPM, max = 3200 RPM)
edge:         +52.0°C  (crit = +118.0°C, hyst = -273.1°C)
                       (emerg = +99.0°C)
junction:     +53.0°C  (crit = +99.0°C, hyst = -273.1°C)
                       (emerg = +99.0°C)
mem:          +72.0°C  (crit = +99.0°C, hyst = -273.1°C)
                       (emerg = +99.0°C)
power1:       29.00 W  (cap = 195.00 W)

nvme-pci-2500
Adapter: PCI adapter
Composite:    +33.9°C  (low  = -273.1°C, high = +69.8°C)
                       (crit = +79.8°C)
Sensor 1:     +34.9°C  (low  = -273.1°C, high = +65261.8°C)
Sensor 2:     +33.9°C  (low  = -273.1°C, high = +65261.8°C)
Sensor 5:     +51.9°C  (low  = -273.1°C, high = +65261.8°C)

Does this look okay? Most of the time the GPU fan is at 0 RPM, while memory is at 72 degrees? 29W looks bit high as well. This is just when it is idle.

Morn

Member

Registered: 2012-09-02

Posts: 886

Re: Checking GPU temperature

My RX480 has min RPM = 1000, but otherwise your values seem quite reasonable.

amdgpu-pci-1c00
Adapter: PCI adapter
vddgfx:      1000.00 mV 
fan1:        1257 RPM  (min = 1000 RPM, max = 3900 RPM)
edge:         +47.0°C  (crit = +94.0°C, hyst = -273.1°C)
power1:       22.12 W  (cap = 110.00 W)