You are not logged in.
- Topics: Active | Unanswered
#1 2020-10-08 08:58:18
- DexterLB
- Member
- Registered: 2011-06-20
- Posts: 51
Multiple stability problems with DP1.2/MST on AMDGPU
Hello,
I have 2 monitors (DELL U2415) connected to a RX5700XT GPU. The primary monitor is connected directly via DisplayPort, and is in DP1.2 mode. The second monitor is daisy-chained to the first one.
I have the following problems:
- Sometimes, as soon as KMS kicks in, the screens are black and won't turn on. Turning them off and on via xrandr sometimes works (and sometimes requires multiple tries for them to turn on)
- Sometimes the screens will turn off randomly for about 0.5sec, every 5-6 seconds. Again, turning them off and on via xrandr several times fixes the problem most of the time.
- When physically turning off the primary monitor, and then turning it back on, the monitors appear as new DisplayPort devices (for example, if they have been DisplayPort-3 and DisplayPort-4, they are now DisplayPort-5 and DisplayPort-6, and the old ones show up as disconnected). This messes up the layout.
- After turning the monitors off and then back on (be it physically or via DPMS), they come back on in one of the unstable states (permanently black or flickering every few seconds).
I have tried the following things:
- Using different DP cables (including the stock DP cable) doesn't help. The flickering looks like data gets corrupted, but I'm inclined to rule out "dodgy cable" as a culprit, since as soon as the screens are restarted into a stable state, they keep stable for days at a time, until being turned off.
- The modes are 1920x1200_59.95. Trying other similar frequencies, like 59.88, doesn't help. (the monitors refuse to go to 60.00)
- Disabling DPM seems to make things better (the flickering state seems to happen much more rarely), but still doesn't solve the black-screen state and the ghost devices, and pins the clocks to low frequencies so rendering is slow.
- I was unable to try disabling DC (which is cited at multiple places for causing flicker), since disabling DC causes the system to reset with a hardware error as soon as it enters KMS
- Disabling specific power management features (clock gating, bapm, aspm) doesn't seem to help
- Pinning the performance profile to "high" or "low", which pins constant clock frequencies, doesn't seem to help
- Whether the card is idle or under huge load doesn't seem to make a difference
So, my question is: how do I debug this further?
The best solution to a problem is usually the easiest one.
Offline
#2 2020-10-08 10:53:58
- Lone_Wolf
- Administrator
- From: Netherlands, Europe
- Registered: 2005-10-04
- Posts: 15,086
Re: Multiple stability problems with DP1.2/MST on AMDGPU
The refresh frequency is calculated from many factors and unsettable directly.
(If you want more info investigate how xorg modelines work) .
Is this on wayland or Xorg ?
What DM / DE / WM are you using ?
Do the errros also oocur with other DE/WM ?
Are both monitors set to DP 1.2 ?
Is audio also transported over the DP connection or just video ?
The RX5700XT should have 3 displayport connectors, do you get similar symptoms when both screens have their own direct connection ?
please post full output of
$ lspci -kAlso journal/dmesg output and xorg log
Last edited by Lone_Wolf (2020-10-08 10:57:35)
Disliking systemd intensely, but not satisfied with alternatives so focusing on taming systemd.
clean chroot building not flexible enough ?
Try clean chroot manager by graysky
Offline
#3 2020-10-08 11:13:42
- DexterLB
- Member
- Registered: 2011-06-20
- Posts: 51
Re: Multiple stability problems with DP1.2/MST on AMDGPU
Lone_Wolf wrote:
The refresh frequency is calculated from many factors and unsettable directly.
(If you want more info investigate how xorg modelines work) .
Yes, I maybe phrased it vaguely: what I did was use cvt to generate a modeline for 1920x1200_60.00, which selected a de-facto frequency of 59.88Hz.
Lone_Wolf wrote:
Is this on wayland or Xorg ?
This is Xorg. For the logs to make sense, I should probably mention that I run two different Xorg servers on two separate identical GPUs (using IsolateDevice). Turning off the other GPU doesn't help with the aforementioned problems.
Lone_Wolf wrote:
What DM / DE / WM are you using ?
i3 with picom as compositor.
Lone_Wolf wrote:
Do the errros also oocur with other DE/WM ?
The problems also occur in the same way with fluxbox and with simply startx and a terminal, without compositor.
Lone_Wolf wrote:
Are both monitors set to DP 1.2 ?
No. As per the monitor instruction manual, the second (last) monitor in the chain is not set to DP1.2. The contrary yields a black screen (as expected).
Lone_Wolf wrote:
Is audio also transported over the DP connection or just video ?
Just video (the audio device is not present in alsamixer). I haven't tried setting amdgpu.audio=0, though.
Lone_Wolf wrote:
The RX5700XT should have 3 displayport connectors, do you get similar symptoms when both screens have their own direct connection ?
Yes.
If both screens are connected using different cables do not use DP1.2, everything is fine.
However, even if 1 monitor is connected using DP1.2, the problems arise.
Lone_Wolf wrote:
please post full output of
$ lspci -k
00:00.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Starship/Matisse Root Complex
Subsystem: Advanced Micro Devices, Inc. [AMD] Device 1450
00:01.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Starship/Matisse PCIe Dummy Host Bridge
00:01.1 PCI bridge: Advanced Micro Devices, Inc. [AMD] Starship/Matisse GPP Bridge
Kernel driver in use: pcieport
00:01.2 PCI bridge: Advanced Micro Devices, Inc. [AMD] Starship/Matisse GPP Bridge
Kernel driver in use: pcieport
00:02.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Starship/Matisse PCIe Dummy Host Bridge
00:03.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Starship/Matisse PCIe Dummy Host Bridge
00:03.1 PCI bridge: Advanced Micro Devices, Inc. [AMD] Starship/Matisse GPP Bridge
Kernel driver in use: pcieport
00:04.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Starship/Matisse PCIe Dummy Host Bridge
00:05.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Starship/Matisse PCIe Dummy Host Bridge
00:07.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Starship/Matisse PCIe Dummy Host Bridge
00:07.1 PCI bridge: Advanced Micro Devices, Inc. [AMD] Starship/Matisse Internal PCIe GPP Bridge 0 to bus[E:B]
Kernel driver in use: pcieport
00:08.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Starship/Matisse PCIe Dummy Host Bridge
00:08.1 PCI bridge: Advanced Micro Devices, Inc. [AMD] Starship/Matisse Internal PCIe GPP Bridge 0 to bus[E:B]
Kernel driver in use: pcieport
00:08.2 PCI bridge: Advanced Micro Devices, Inc. [AMD] Starship/Matisse Internal PCIe GPP Bridge 0 to bus[E:B]
Kernel driver in use: pcieport
00:08.3 PCI bridge: Advanced Micro Devices, Inc. [AMD] Starship/Matisse Internal PCIe GPP Bridge 0 to bus[E:B]
Kernel driver in use: pcieport
00:14.0 SMBus: Advanced Micro Devices, Inc. [AMD] FCH SMBus Controller (rev 61)
Subsystem: Gigabyte Technology Co., Ltd Device 5001
Kernel modules: i2c_piix4, sp5100_tco
00:14.3 ISA bridge: Advanced Micro Devices, Inc. [AMD] FCH LPC Bridge (rev 51)
Subsystem: Gigabyte Technology Co., Ltd Device 5001
00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Matisse Device 24: Function 0
00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] Matisse Device 24: Function 1
00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] Matisse Device 24: Function 2
00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] Matisse Device 24: Function 3
Kernel driver in use: k10temp
Kernel modules: k10temp
00:18.4 Host bridge: Advanced Micro Devices, Inc. [AMD] Matisse Device 24: Function 4
00:18.5 Host bridge: Advanced Micro Devices, Inc. [AMD] Matisse Device 24: Function 5
00:18.6 Host bridge: Advanced Micro Devices, Inc. [AMD] Matisse Device 24: Function 6
00:18.7 Host bridge: Advanced Micro Devices, Inc. [AMD] Matisse Device 24: Function 7
01:00.0 Non-Volatile memory controller: Samsung Electronics Co Ltd NVMe SSD Controller SM981/PM981/PM983
Subsystem: Samsung Electronics Co Ltd Device a801
Kernel driver in use: nvme
02:00.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] Matisse Switch Upstream
Kernel driver in use: pcieport
03:02.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] Matisse PCIe GPP Bridge
Kernel driver in use: pcieport
03:04.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] Matisse PCIe GPP Bridge
Kernel driver in use: pcieport
03:08.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] Matisse PCIe GPP Bridge
Kernel driver in use: pcieport
03:09.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] Matisse PCIe GPP Bridge
Kernel driver in use: pcieport
03:0a.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] Matisse PCIe GPP Bridge
Kernel driver in use: pcieport
04:00.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] Navi 10 XL Upstream Port of PCI Express Switch (rev c1)
Kernel driver in use: pcieport
05:00.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] Navi 10 XL Downstream Port of PCI Express Switch
Kernel driver in use: pcieport
06:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Navi 10 [Radeon RX 5600 OEM/5600 XT / 5700/5700 XT] (rev c1)
Subsystem: Sapphire Technology Limited Device e410
Kernel driver in use: amdgpu
Kernel modules: amdgpu
06:00.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] Navi 10 HDMI Audio
Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] Navi 10 HDMI Audio
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 16)
Subsystem: Gigabyte Technology Co., Ltd Onboard Ethernet
Kernel driver in use: r8169
Kernel modules: r8169
08:00.0 Non-Essential Instrumentation [1300]: Advanced Micro Devices, Inc. [AMD] Starship/Matisse Reserved SPP
Subsystem: Advanced Micro Devices, Inc. [AMD] Starship/Matisse Reserved SPP
08:00.1 USB controller: Advanced Micro Devices, Inc. [AMD] Matisse USB 3.0 Host Controller
Subsystem: Advanced Micro Devices, Inc. [AMD] Device 1486
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
08:00.3 USB controller: Advanced Micro Devices, Inc. [AMD] Matisse USB 3.0 Host Controller
Subsystem: Advanced Micro Devices, Inc. [AMD] Device 148c
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
09:00.0 SATA controller: Advanced Micro Devices, Inc. [AMD] FCH SATA Controller [AHCI mode] (rev 51)
Subsystem: Advanced Micro Devices, Inc. [AMD] FCH SATA Controller [AHCI mode]
Kernel driver in use: ahci
0a:00.0 SATA controller: Advanced Micro Devices, Inc. [AMD] FCH SATA Controller [AHCI mode] (rev 51)
Subsystem: Advanced Micro Devices, Inc. [AMD] FCH SATA Controller [AHCI mode]
Kernel driver in use: ahci
0b:00.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] Navi 10 XL Upstream Port of PCI Express Switch (rev c1)
Kernel driver in use: pcieport
0c:00.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] Navi 10 XL Downstream Port of PCI Express Switch
Kernel driver in use: pcieport
0d:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Navi 10 [Radeon RX 5600 OEM/5600 XT / 5700/5700 XT] (rev c1)
Subsystem: Sapphire Technology Limited Device e410
Kernel driver in use: amdgpu
Kernel modules: amdgpu
0d:00.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] Navi 10 HDMI Audio
Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] Navi 10 HDMI Audio
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
0e:00.0 Non-Essential Instrumentation [1300]: Advanced Micro Devices, Inc. [AMD] Starship/Matisse PCIe Dummy Function
Subsystem: Advanced Micro Devices, Inc. [AMD] Starship/Matisse PCIe Dummy Function
0f:00.0 Non-Essential Instrumentation [1300]: Advanced Micro Devices, Inc. [AMD] Starship/Matisse Reserved SPP
Subsystem: Advanced Micro Devices, Inc. [AMD] Starship/Matisse Reserved SPP
0f:00.1 Encryption controller: Advanced Micro Devices, Inc. [AMD] Starship/Matisse Cryptographic Coprocessor PSPCPP
Subsystem: Advanced Micro Devices, Inc. [AMD] Starship/Matisse Cryptographic Coprocessor PSPCPP
Kernel driver in use: ccp
Kernel modules: ccp
0f:00.3 USB controller: Advanced Micro Devices, Inc. [AMD] Matisse USB 3.0 Host Controller
Subsystem: Gigabyte Technology Co., Ltd Device 5007
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
0f:00.4 Audio device: Advanced Micro Devices, Inc. [AMD] Starship/Matisse HD Audio Controller
Subsystem: Gigabyte Technology Co., Ltd Device a184
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
10:00.0 SATA controller: Advanced Micro Devices, Inc. [AMD] FCH SATA Controller [AHCI mode] (rev 51)
Subsystem: Gigabyte Technology Co., Ltd Device b002
Kernel driver in use: ahci
11:00.0 SATA controller: Advanced Micro Devices, Inc. [AMD] FCH SATA Controller [AHCI mode] (rev 51)
Subsystem: Gigabyte Technology Co., Ltd Device b002
Kernel driver in use: ahciLone_Wolf wrote:
Also journal/dmesg output and xorg log
xorg log of the relevant X server:
[ 118.501]
X.Org X Server 1.20.9
X Protocol Version 11, Revision 0
[ 118.501] Build Operating System: Linux Arch Linux
[ 118.501] Current Operating System: Linux gallifrey 5.8.13-arch1-1 #1 SMP PREEMPT Thu, 01 Oct 2020 20:40:35 +0000 x86_64
[ 118.501] Kernel command line: BOOT_IMAGE=/root/boot/vmlinuz-linux root=/dev/mapper/gfr_crypt rw rootflags=subvol=root rd.luks.name=62f43f28-4668-44da-ac39-788721ef82c7=gfr_crypt rd.luks.key=/var/keys/self.key rd.luks.options=discard loglevel=4
[ 118.501] Build Date: 02 September 2020 06:17:44AM
[ 118.501]
[ 118.501] Current version of pixman: 0.40.0
[ 118.501] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 118.501] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 118.501] (==) Log file: "/var/log/Xorg.1.log", Time: Thu Oct 8 11:18:31 2020
[ 118.501] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 118.501] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 118.501] (==) ServerLayout "seat1"
[ 118.501] (==) No screen section available. Using defaults.
[ 118.501] (**) |-->Screen "Default Screen Section" (0)
[ 118.501] (**) | |-->Monitor "<default monitor>"
[ 118.501] (==) No device specified for screen "Default Screen Section".
Using the first device section listed.
[ 118.501] (**) | |-->Device "gpu1"
[ 118.501] (**) | |-->GPUDevice "gpu1"
[ 118.501] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 118.501] (**) Option "SingleCard" "on"
[ 118.501] (**) Option "AutoAddGPU" "off"
[ 118.501] (==) Automatically adding devices
[ 118.501] (==) Automatically enabling devices
[ 118.501] (**) Not automatically adding GPU devices
[ 118.501] (==) Automatically binding GPU devices
[ 118.501] (==) Max clients allowed: 256, resource mask: 0x1fffff
[ 118.501] (WW) The directory "/usr/share/fonts/misc" does not exist.
[ 118.501] Entry deleted from font path.
[ 118.501] (WW) The directory "/usr/share/fonts/Type1" does not exist.
[ 118.501] Entry deleted from font path.
[ 118.501] (WW) The directory "/usr/share/fonts/100dpi" does not exist.
[ 118.501] Entry deleted from font path.
[ 118.501] (WW) The directory "/usr/share/fonts/75dpi" does not exist.
[ 118.501] Entry deleted from font path.
[ 118.501] (==) FontPath set to:
/usr/share/fonts/TTF,
/usr/share/fonts/OTF
[ 118.501] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 118.501] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 118.501] (II) Module ABI versions:
[ 118.501] X.Org ANSI C Emulation: 0.4
[ 118.501] X.Org Video Driver: 24.1
[ 118.501] X.Org XInput driver : 24.1
[ 118.501] X.Org Server Extension : 10.0
[ 118.502] (EE) systemd-logind: failed to get session: PID 1985 does not belong to any known session
[ 118.504] (II) xfree86: Adding drm device (/dev/dri/card1)[ 111.855637] FS-Cache: Loaded
[ 111.856737] Key type dns_resolver registered
[ 111.890335] FS-Cache: Netfs 'cifs' registered for caching
[ 111.892986] Key type cifs.spnego registered
[ 111.892990] Key type cifs.idmap registered
[ 111.893443] CIFS: Attempting to mount //skaro/davros
[ 111.893464] CIFS: No dialect specified on mount. Default has changed to a more secure dialect, SMB2.1 or later (e.g. SMB3.1.1), from CIFS (SMB1). To use the less secure SMB1 dialect to access old servers which do not support SMB3.1.1 (or even SMB3 or SMB2.1) specify vers=1.0 on mount.
[ 3929.956810] logitech-hidpp-device 0003:046D:404D.0006: HID++ 4.1 device connected.
[ 118.504] (II) Platform probe for /sys/devices/pci0000:00/0000:00:03.1/0000:0b:00.0/0000:0c:00.0/0000:0d:00.0/drm/card1
[ 118.506] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 118.506] (II) LoadModule: "glx"
[ 118.506] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 118.507] (II) Module glx: vendor="X.Org Foundation"
[ 118.507] compiled for 1.20.9, module version = 1.0.0
[ 118.507] ABI class: X.Org Server Extension, version 10.0
[ 118.507] (II) LoadModule: "amdgpu"
[ 118.507] (II) Loading /usr/lib/xorg/modules/drivers/amdgpu_drv.so
[ 118.508] (II) Module amdgpu: vendor="X.Org Foundation"
[ 118.508] compiled for 1.20.8, module version = 19.1.0
[ 118.508] Module class: X.Org Video Driver
[ 118.508] ABI class: X.Org Video Driver, version 24.1
[ 118.508] (II) AMDGPU: Driver for AMD Radeon:
All GPUs supported by the amdgpu kernel driver
[ 118.508] (II) AMDGPU(0): [KMS] Kernel modesetting enabled.
[ 118.508] (II) AMDGPU(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 118.508] (==) AMDGPU(0): Depth 24, (--) framebuffer bpp 32
[ 118.508] (II) AMDGPU(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
[ 118.508] (==) AMDGPU(0): Default visual is TrueColor
[ 118.508] (==) AMDGPU(0): RGB weight 888
[ 118.508] (II) AMDGPU(0): Using 8 bits per RGB (8 bit DAC)
[ 118.508] (--) AMDGPU(0): Chipset: "AMD Radeon RX 5700 XT" (ChipID = 0x731f)
[ 118.508] (II) Loading sub module "fb"
[ 118.508] (II) LoadModule: "fb"
[ 118.508] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 118.508] (II) Module fb: vendor="X.Org Foundation"
[ 118.508] compiled for 1.20.9, module version = 1.0.0
[ 118.508] ABI class: X.Org ANSI C Emulation, version 0.4
[ 118.508] (II) Loading sub module "dri2"
[ 118.508] (II) LoadModule: "dri2"
[ 118.508] (II) Module "dri2" already built-in
[ 118.560] (II) Loading sub module "glamoregl"
[ 118.560] (II) LoadModule: "glamoregl"
[ 118.561] (II) Loading /usr/lib/xorg/modules/libglamoregl.so
[ 118.564] (II) Module glamoregl: vendor="X.Org Foundation"
[ 118.564] compiled for 1.20.9, module version = 1.0.1
[ 118.564] ABI class: X.Org ANSI C Emulation, version 0.4
[ 118.575] (II) AMDGPU(0): glamor X acceleration enabled on AMD Radeon RX 5700 XT (NAVI10, DRM 3.38.0, 5.8.13-arch1-1, LLVM 10.0.1)
[ 118.575] (II) AMDGPU(0): glamor detected, initialising EGL layer.
[ 118.575] (==) AMDGPU(0): TearFree property default: auto
[ 118.575] (==) AMDGPU(0): VariableRefresh: disabled
[ 118.575] (II) AMDGPU(0): KMS Pageflipping: enabled
[ 118.575] (II) AMDGPU(0): Output DisplayPort-0 has no monitor section
[ 118.575] (II) AMDGPU(0): Output DisplayPort-1 has no monitor section
[ 118.575] (II) AMDGPU(0): Output HDMI-A-0 has no monitor section
[ 118.575] (II) AMDGPU(0): Output HDMI-A-1 has no monitor section
[ 118.575] (II) AMDGPU(0): Output DisplayPort-2 has no monitor section
[ 118.576] (II) AMDGPU(0): Output DisplayPort-3 has no monitor section
[ 118.607] (II) AMDGPU(0): EDID for output DisplayPort-0
[ 118.607] (II) AMDGPU(0): EDID for output DisplayPort-1
[ 118.607] (II) AMDGPU(0): EDID for output HDMI-A-0
[ 118.607] (II) AMDGPU(0): EDID for output HDMI-A-1
[ 118.607] (II) AMDGPU(0): EDID for output DisplayPort-2
[ 118.607] (II) AMDGPU(0): Manufacturer: DEL Model: a0b8 Serial#: 809588300
[ 118.607] (II) AMDGPU(0): Year: 2019 Week: 2
[ 118.607] (II) AMDGPU(0): EDID Version: 1.4
[ 118.607] (II) AMDGPU(0): Digital Display Input
[ 118.607] (II) AMDGPU(0): 8 bits per channel
[ 118.607] (II) AMDGPU(0): Digital interface is DisplayPort
[ 118.607] (II) AMDGPU(0): Max Image Size [cm]: horiz.: 52 vert.: 32
[ 118.607] (II) AMDGPU(0): Gamma: 2.20
[ 118.607] (II) AMDGPU(0): DPMS capabilities: Off
[ 118.607] (II) AMDGPU(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 YCrCb 4:2:2
[ 118.607] (II) AMDGPU(0): First detailed timing is preferred mode
[ 118.607] (II) AMDGPU(0): Preferred mode is native pixel format and refresh rate
[ 118.607] (II) AMDGPU(0): redX: 0.660 redY: 0.332 greenX: 0.302 greenY: 0.613
[ 118.607] (II) AMDGPU(0): blueX: 0.150 blueY: 0.063 whiteX: 0.313 whiteY: 0.329
[ 118.607] (II) AMDGPU(0): Supported established timings:
[ 118.607] (II) AMDGPU(0): 720x400@70Hz
[ 118.607] (II) AMDGPU(0): 640x480@60Hz
[ 118.607] (II) AMDGPU(0): 640x480@75Hz
[ 118.607] (II) AMDGPU(0): 800x600@60Hz
[ 118.607] (II) AMDGPU(0): 800x600@75Hz
[ 118.607] (II) AMDGPU(0): 1024x768@60Hz
[ 118.607] (II) AMDGPU(0): 1024x768@75Hz
[ 118.607] (II) AMDGPU(0): 1280x1024@75Hz
[ 118.607] (II) AMDGPU(0): Manufacturer's mask: 0
[ 118.607] (II) AMDGPU(0): Supported standard timings:
[ 118.607] (II) AMDGPU(0): #0: hsize: 1152 vsize 864 refresh: 75 vid: 20337
[ 118.607] (II) AMDGPU(0): #1: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
[ 118.607] (II) AMDGPU(0): #2: hsize: 1600 vsize 1200 refresh: 60 vid: 16553
[ 118.607] (II) AMDGPU(0): #3: hsize: 1920 vsize 1080 refresh: 60 vid: 49361
[ 118.607] (II) AMDGPU(0): #4: hsize: 1920 vsize 1200 refresh: 60 vid: 209
[ 118.607] (II) AMDGPU(0): Supported detailed timing:
[ 118.607] (II) AMDGPU(0): clock: 154.0 MHz Image Size: 518 x 324 mm
[ 118.607] (II) AMDGPU(0): h_active: 1920 h_sync: 1968 h_sync_end 2000 h_blank_end 2080 h_border: 0
[ 118.607] (II) AMDGPU(0): v_active: 1200 v_sync: 1203 v_sync_end 1209 v_blanking: 1235 v_border: 0
[ 118.607] (II) AMDGPU(0): Serial No: 7MT0191C0AVL
[ 118.608] (II) AMDGPU(0): Monitor name: DELL U2415
[ 118.608] (II) AMDGPU(0): Ranges: V min: 49 V max: 61 Hz, H min: 30 H max: 83 kHz, PixClock max 175 MHz
[ 118.608] (II) AMDGPU(0): Supported detailed timing:
[ 118.608] (II) AMDGPU(0): clock: 148.5 MHz Image Size: 518 x 324 mm
[ 118.608] (II) AMDGPU(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
[ 118.608] (II) AMDGPU(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
[ 118.608] (II) AMDGPU(0): Supported detailed timing:
[ 118.608] (II) AMDGPU(0): clock: 74.2 MHz Image Size: 518 x 324 mm
[ 118.608] (II) AMDGPU(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
[ 118.608] (II) AMDGPU(0): v_active: 540 v_sync: 542 v_sync_end 547 v_blanking: 562 v_border: 0
[ 118.608] (II) AMDGPU(0): Supported detailed timing:
[ 118.608] (II) AMDGPU(0): clock: 74.2 MHz Image Size: 518 x 324 mm
[ 118.608] (II) AMDGPU(0): h_active: 1280 h_sync: 1390 h_sync_end 1430 h_blank_end 1650 h_border: 0
[ 118.608] (II) AMDGPU(0): v_active: 720 v_sync: 725 v_sync_end 730 v_blanking: 750 v_border: 0
[ 118.608] (II) AMDGPU(0): Supported detailed timing:
[ 118.608] (II) AMDGPU(0): clock: 27.0 MHz Image Size: 518 x 324 mm
[ 118.608] (II) AMDGPU(0): h_active: 720 h_sync: 736 h_sync_end 798 h_blank_end 858 h_border: 0
[ 118.608] (II) AMDGPU(0): v_active: 480 v_sync: 489 v_sync_end 495 v_blanking: 525 v_border: 0
[ 118.608] (II) AMDGPU(0): Number of EDID sections to follow: 1
[ 118.608] (II) AMDGPU(0): EDID (in hex):
[ 118.608] (II) AMDGPU(0): 00ffffffffffff0010acb8a04c564130
[ 118.608] (II) AMDGPU(0): 021d0104a53420783a0495a9554d9d26
[ 118.608] (II) AMDGPU(0): 105054a54b00714f8180a940d1c0d100
[ 118.608] (II) AMDGPU(0): 010101010101283c80a070b023403020
[ 118.608] (II) AMDGPU(0): 360006442100001e000000ff00374d54
[ 118.608] (II) AMDGPU(0): 30313931433041564c0a000000fc0044
[ 118.608] (II) AMDGPU(0): 454c4c2055323431350a2020000000fd
[ 118.608] (II) AMDGPU(0): 00313d1e5311000a202020202020013b
[ 118.608] (II) AMDGPU(0): 02031cf14f9005040302071601141f12
[ 118.608] (II) AMDGPU(0): 132021222309070783010000023a8018
[ 118.608] (II) AMDGPU(0): 71382d40582c450006442100001e011d
[ 118.608] (II) AMDGPU(0): 8018711c1620582c250006442100009e
[ 118.608] (II) AMDGPU(0): 011d007251d01e206e28550006442100
[ 118.608] (II) AMDGPU(0): 001e8c0ad08a20e02d10103e96000644
[ 118.608] (II) AMDGPU(0): 21000018000000000000000000000000
[ 118.608] (II) AMDGPU(0): 0000000000000000000000000000000c
[ 118.608] (II) AMDGPU(0): Printing probed modes for output DisplayPort-2
[ 118.608] (II) AMDGPU(0): Modeline "1920x1200"x60.0 154.00 1920 1968 2000 2080 1200 1203 1209 1235 +hsync +vsync (74.0 kHz eP)
[ 118.608] (II) AMDGPU(0): Modeline "1920x1080"x60.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz e)
[ 118.608] (II) AMDGPU(0): Modeline "1920x1080"x50.0 148.50 1920 2448 2492 2640 1080 1084 1089 1125 +hsync +vsync (56.2 kHz e)
[ 118.608] (II) AMDGPU(0): Modeline "1920x1080"x59.9 148.35 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.4 kHz e)
[ 118.608] (II) AMDGPU(0): Modeline "1920x1080"x30.0 74.25 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (33.8 kHz e)
[ 118.608] (II) AMDGPU(0): Modeline "1920x1080"x25.0 74.25 1920 2448 2492 2640 1080 1084 1089 1125 +hsync +vsync (28.1 kHz e)
[ 118.608] (II) AMDGPU(0): Modeline "1920x1080"x24.0 74.25 1920 2558 2602 2750 1080 1084 1089 1125 +hsync +vsync (27.0 kHz e)
[ 118.608] (II) AMDGPU(0): Modeline "1920x1080"x30.0 74.18 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (33.7 kHz e)
[ 118.608] (II) AMDGPU(0): Modeline "1920x1080"x24.0 74.18 1920 2558 2602 2750 1080 1084 1089 1125 +hsync +vsync (27.0 kHz e)
[ 118.608] (II) AMDGPU(0): Modeline "1600x1200"x60.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz e)
[ 118.608] (II) AMDGPU(0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[ 118.608] (II) AMDGPU(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[ 118.608] (II) AMDGPU(0): Modeline "1152x864"x75.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 118.608] (II) AMDGPU(0): Modeline "1280x720"x60.0 74.25 1280 1390 1430 1650 720 725 730 750 +hsync +vsync (45.0 kHz e)
[ 118.608] (II) AMDGPU(0): Modeline "1280x720"x50.0 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync (37.5 kHz e)
[ 118.608] (II) AMDGPU(0): Modeline "1280x720"x59.9 74.18 1280 1390 1430 1650 720 725 730 750 +hsync +vsync (45.0 kHz e)
[ 118.608] (II) AMDGPU(0): Modeline "1024x768"x75.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz e)
[ 118.608] (II) AMDGPU(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 118.608] (II) AMDGPU(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 118.608] (II) AMDGPU(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 118.608] (II) AMDGPU(0): Modeline "720x576"x50.0 27.00 720 732 796 864 576 581 586 625 -hsync -vsync (31.2 kHz e)
[ 118.608] (II) AMDGPU(0): Modeline "720x480"x60.0 27.03 720 736 798 858 480 489 495 525 -hsync -vsync (31.5 kHz e)
[ 118.608] (II) AMDGPU(0): Modeline "720x480"x59.9 27.00 720 736 798 858 480 489 495 525 -hsync -vsync (31.5 kHz e)
[ 118.608] (II) AMDGPU(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 118.608] (II) AMDGPU(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 118.608] (II) AMDGPU(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 118.608] (II) AMDGPU(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 118.609] (II) AMDGPU(0): EDID for output DisplayPort-3
[ 118.609] (II) AMDGPU(0): Manufacturer: DEL Model: a0b9 Serial#: 825315916
[ 118.609] (II) AMDGPU(0): Year: 2020 Week: 18
[ 118.609] (II) AMDGPU(0): EDID Version: 1.4
[ 118.609] (II) AMDGPU(0): Digital Display Input
[ 118.609] (II) AMDGPU(0): 8 bits per channel
[ 118.609] (II) AMDGPU(0): Digital interface is DisplayPort
[ 118.609] (II) AMDGPU(0): Max Image Size [cm]: horiz.: 52 vert.: 32
[ 118.609] (II) AMDGPU(0): Gamma: 2.20
[ 118.609] (II) AMDGPU(0): DPMS capabilities: Off
[ 118.609] (II) AMDGPU(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 YCrCb 4:2:2
[ 118.609] (II) AMDGPU(0): First detailed timing is preferred mode
[ 118.609] (II) AMDGPU(0): Preferred mode is native pixel format and refresh rate
[ 118.609] (II) AMDGPU(0): redX: 0.660 redY: 0.332 greenX: 0.302 greenY: 0.613
[ 118.609] (II) AMDGPU(0): blueX: 0.150 blueY: 0.063 whiteX: 0.313 whiteY: 0.329
[ 118.609] (II) AMDGPU(0): Supported established timings:
[ 118.609] (II) AMDGPU(0): 720x400@70Hz
[ 118.609] (II) AMDGPU(0): 640x480@60Hz
[ 118.609] (II) AMDGPU(0): 640x480@75Hz
[ 118.609] (II) AMDGPU(0): 800x600@60Hz
[ 118.609] (II) AMDGPU(0): 800x600@75Hz
[ 118.609] (II) AMDGPU(0): 1024x768@60Hz
[ 118.609] (II) AMDGPU(0): 1024x768@75Hz
[ 118.609] (II) AMDGPU(0): 1280x1024@75Hz
[ 118.609] (II) AMDGPU(0): Manufacturer's mask: 0
[ 118.609] (II) AMDGPU(0): Supported standard timings:
[ 118.609] (II) AMDGPU(0): #0: hsize: 1152 vsize 864 refresh: 75 vid: 20337
[ 118.609] (II) AMDGPU(0): #1: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
[ 118.609] (II) AMDGPU(0): #2: hsize: 1600 vsize 1200 refresh: 60 vid: 16553
[ 118.609] (II) AMDGPU(0): #3: hsize: 1920 vsize 1080 refresh: 60 vid: 49361
[ 118.609] (II) AMDGPU(0): #4: hsize: 1920 vsize 1200 refresh: 60 vid: 209
[ 118.609] (II) AMDGPU(0): Supported detailed timing:
[ 118.609] (II) AMDGPU(0): clock: 154.0 MHz Image Size: 518 x 324 mm
[ 118.609] (II) AMDGPU(0): h_active: 1920 h_sync: 1968 h_sync_end 2000 h_blank_end 2080 h_border: 0
[ 118.609] (II) AMDGPU(0): v_active: 1200 v_sync: 1203 v_sync_end 1209 v_blanking: 1235 v_border: 0
[ 118.609] (II) AMDGPU(0): Serial No: XKV0P04S11RL
[ 118.609] (II) AMDGPU(0): Monitor name: DELL U2415
[ 118.609] (II) AMDGPU(0): Ranges: V min: 49 V max: 61 Hz, H min: 30 H max: 83 kHz, PixClock max 175 MHz
[ 118.609] (II) AMDGPU(0): Supported detailed timing:
[ 118.609] (II) AMDGPU(0): clock: 148.5 MHz Image Size: 518 x 324 mm
[ 118.609] (II) AMDGPU(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
[ 118.609] (II) AMDGPU(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
[ 118.609] (II) AMDGPU(0): Supported detailed timing:
[ 118.609] (II) AMDGPU(0): clock: 74.2 MHz Image Size: 518 x 324 mm
[ 118.609] (II) AMDGPU(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
[ 118.609] (II) AMDGPU(0): v_active: 540 v_sync: 542 v_sync_end 547 v_blanking: 562 v_border: 0
[ 118.609] (II) AMDGPU(0): Supported detailed timing:
[ 118.609] (II) AMDGPU(0): clock: 74.2 MHz Image Size: 518 x 324 mm
[ 118.609] (II) AMDGPU(0): h_active: 1280 h_sync: 1390 h_sync_end 1430 h_blank_end 1650 h_border: 0
[ 118.609] (II) AMDGPU(0): v_active: 720 v_sync: 725 v_sync_end 730 v_blanking: 750 v_border: 0
[ 118.609] (II) AMDGPU(0): Supported detailed timing:
[ 118.609] (II) AMDGPU(0): clock: 27.0 MHz Image Size: 518 x 324 mm
[ 118.609] (II) AMDGPU(0): h_active: 720 h_sync: 736 h_sync_end 798 h_blank_end 858 h_border: 0
[ 118.609] (II) AMDGPU(0): v_active: 480 v_sync: 489 v_sync_end 495 v_blanking: 525 v_border: 0
[ 118.609] (II) AMDGPU(0): Number of EDID sections to follow: 1
[ 118.609] (II) AMDGPU(0): EDID (in hex):
[ 118.609] (II) AMDGPU(0): 00ffffffffffff0010acb9a04c523131
[ 118.609] (II) AMDGPU(0): 121e0104a53420783a0495a9554d9d26
[ 118.609] (II) AMDGPU(0): 105054a54b00714f8180a940d1c0d100
[ 118.609] (II) AMDGPU(0): 010101010101283c80a070b023403020
[ 118.609] (II) AMDGPU(0): 360006442100001e000000ff00584b56
[ 118.609] (II) AMDGPU(0): 30503034533131524c0a000000fc0044
[ 118.609] (II) AMDGPU(0): 454c4c2055323431350a2020000000fd
[ 118.609] (II) AMDGPU(0): 00313d1e5311000a2020202020200105
[ 118.609] (II) AMDGPU(0): 02031cf14f9005040302071601141f12
[ 118.609] (II) AMDGPU(0): 132021222309070783010000023a8018
[ 118.609] (II) AMDGPU(0): 71382d40582c450006442100001e011d
[ 118.609] (II) AMDGPU(0): 8018711c1620582c250006442100009e
[ 118.609] (II) AMDGPU(0): 011d007251d01e206e28550006442100
[ 118.609] (II) AMDGPU(0): 001e8c0ad08a20e02d10103e96000644
[ 118.609] (II) AMDGPU(0): 21000018000000000000000000000000
[ 118.609] (II) AMDGPU(0): 0000000000000000000000000000000c
[ 118.609] (II) AMDGPU(0): Printing probed modes for output DisplayPort-3
[ 118.609] (II) AMDGPU(0): Modeline "1920x1200"x60.0 154.00 1920 1968 2000 2080 1200 1203 1209 1235 +hsync +vsync (74.0 kHz eP)
[ 118.609] (II) AMDGPU(0): Modeline "1920x1080"x60.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz e)
[ 118.609] (II) AMDGPU(0): Modeline "1920x1080"x50.0 148.50 1920 2448 2492 2640 1080 1084 1089 1125 +hsync +vsync (56.2 kHz e)
[ 118.609] (II) AMDGPU(0): Modeline "1920x1080"x59.9 148.35 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.4 kHz e)
[ 118.609] (II) AMDGPU(0): Modeline "1920x1080"x30.0 74.25 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (33.8 kHz e)
[ 118.610] (II) AMDGPU(0): Modeline "1920x1080"x25.0 74.25 1920 2448 2492 2640 1080 1084 1089 1125 +hsync +vsync (28.1 kHz e)
[ 118.610] (II) AMDGPU(0): Modeline "1920x1080"x24.0 74.25 1920 2558 2602 2750 1080 1084 1089 1125 +hsync +vsync (27.0 kHz e)
[ 118.610] (II) AMDGPU(0): Modeline "1920x1080"x30.0 74.18 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (33.7 kHz e)
[ 118.610] (II) AMDGPU(0): Modeline "1920x1080"x24.0 74.18 1920 2558 2602 2750 1080 1084 1089 1125 +hsync +vsync (27.0 kHz e)
[ 118.610] (II) AMDGPU(0): Modeline "1600x1200"x60.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz e)
[ 118.610] (II) AMDGPU(0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[ 118.610] (II) AMDGPU(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[ 118.610] (II) AMDGPU(0): Modeline "1152x864"x75.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 118.610] (II) AMDGPU(0): Modeline "1280x720"x60.0 74.25 1280 1390 1430 1650 720 725 730 750 +hsync +vsync (45.0 kHz e)
[ 118.610] (II) AMDGPU(0): Modeline "1280x720"x50.0 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync (37.5 kHz e)
[ 118.610] (II) AMDGPU(0): Modeline "1280x720"x59.9 74.18 1280 1390 1430 1650 720 725 730 750 +hsync +vsync (45.0 kHz e)
[ 118.610] (II) AMDGPU(0): Modeline "1024x768"x75.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz e)
[ 118.610] (II) AMDGPU(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 118.610] (II) AMDGPU(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 118.610] (II) AMDGPU(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 118.610] (II) AMDGPU(0): Modeline "720x576"x50.0 27.00 720 732 796 864 576 581 586 625 -hsync -vsync (31.2 kHz e)
[ 118.610] (II) AMDGPU(0): Modeline "720x480"x60.0 27.03 720 736 798 858 480 489 495 525 -hsync -vsync (31.5 kHz e)
[ 118.610] (II) AMDGPU(0): Modeline "720x480"x59.9 27.00 720 736 798 858 480 489 495 525 -hsync -vsync (31.5 kHz e)
[ 118.610] (II) AMDGPU(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 118.610] (II) AMDGPU(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 118.610] (II) AMDGPU(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 118.610] (II) AMDGPU(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 118.610] (II) AMDGPU(0): Output DisplayPort-0 disconnected
[ 118.610] (II) AMDGPU(0): Output DisplayPort-1 disconnected
[ 118.610] (II) AMDGPU(0): Output HDMI-A-0 disconnected
[ 118.610] (II) AMDGPU(0): Output HDMI-A-1 disconnected
[ 118.610] (II) AMDGPU(0): Output DisplayPort-2 connected
[ 118.610] (II) AMDGPU(0): Output DisplayPort-3 connected
[ 118.610] (II) AMDGPU(0): Using spanning desktop for initial modes
[ 118.610] (II) AMDGPU(0): Output DisplayPort-2 using initial mode 1920x1200 +0+0
[ 118.610] (II) AMDGPU(0): Output DisplayPort-3 using initial mode 1920x1200 +1920+0
[ 118.610] (II) AMDGPU(0): mem size init: gart size :1fe5bd000 vram size: s:1fd85c000 visible:f56a000
[ 118.610] (==) AMDGPU(0): DPI set to (96, 96)
[ 118.610] (==) AMDGPU(0): Using gamma correction (1.0, 1.0, 1.0)
[ 118.610] (II) Loading sub module "ramdac"
[ 118.610] (II) LoadModule: "ramdac"
[ 118.610] (II) Module "ramdac" already built-in
[ 118.610] (II) AMDGPU(0): [DRI2] Setup complete
[ 118.610] (II) AMDGPU(0): [DRI2] DRI driver: radeonsi
[ 118.610] (II) AMDGPU(0): [DRI2] VDPAU driver: radeonsi
[ 118.610] (II) AMDGPU(0): Front buffer pitch: 15360 bytes
[ 118.610] (II) AMDGPU(0): SYNC extension fences enabled
[ 118.610] (II) AMDGPU(0): Present extension enabled
[ 118.610] (==) AMDGPU(0): DRI3 enabled
[ 118.610] (==) AMDGPU(0): Backing store enabled
[ 118.610] (II) AMDGPU(0): Direct rendering enabled
[ 118.618] (II) AMDGPU(0): Use GLAMOR acceleration.
[ 118.618] (II) AMDGPU(0): Acceleration enabled
[ 118.618] (==) AMDGPU(0): DPMS enabled
[ 118.618] (==) AMDGPU(0): Silken mouse disabled
[ 118.618] (II) AMDGPU(0): Set up textured video (glamor)
[ 118.658] (II) Initializing extension Generic Event Extension
[ 118.658] (II) Initializing extension SHAPE
[ 118.658] (II) Initializing extension MIT-SHM
[ 118.658] (II) Initializing extension XInputExtension
[ 118.658] (II) Initializing extension XTEST
[ 118.658] (II) Initializing extension BIG-REQUESTS
[ 118.658] (II) Initializing extension SYNC
[ 118.659] (II) Initializing extension XKEYBOARD
[ 118.659] (II) Initializing extension XC-MISC
[ 118.659] (II) Initializing extension SECURITY
[ 118.659] (II) Initializing extension XFIXES
[ 118.659] (II) Initializing extension RENDER
[ 118.659] (II) Initializing extension RANDR
[ 118.660] (II) Initializing extension COMPOSITE
[ 118.660] (II) Initializing extension DAMAGE
[ 118.660] (II) Initializing extension MIT-SCREEN-SAVER
[ 118.660] (II) Initializing extension DOUBLE-BUFFER
[ 118.660] (II) Initializing extension RECORD
[ 118.660] (II) Initializing extension DPMS
[ 118.660] (II) Initializing extension Present
[ 118.660] (II) Initializing extension DRI3
[ 118.661] (II) Initializing extension X-Resource
[ 118.661] (II) Initializing extension XVideo
[ 118.661] (II) Initializing extension XVideo-MotionCompensation
[ 118.661] (II) Initializing extension GLX
[ 118.666] (II) AIGLX: Loaded and initialized radeonsi
[ 118.666] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 118.666] (II) Initializing extension XFree86-VidModeExtension
[ 118.667] (II) Initializing extension XFree86-DGA
[ 118.667] (II) Initializing extension XFree86-DRI
[ 118.667] (II) Initializing extension DRI2
[ 118.668] (II) AMDGPU(0): Setting screen physical size to 1016 x 317
[ 118.761] (II) config/udev: Adding input device LITE-ON Technology USB NetVista Full Width Keyboard. (/dev/input/event25)
[ 118.761] (**) LITE-ON Technology USB NetVista Full Width Keyboard.: Applying InputClass "libinput keyboard catchall"
[ 118.761] (II) LoadModule: "libinput"
[ 118.761] (II) Loading /usr/lib/xorg/modules/input/libinput_drv.so
[ 118.763] (II) Module libinput: vendor="X.Org Foundation"
[ 118.763] compiled for 1.20.8, module version = 0.30.0
[ 118.763] Module class: X.Org XInput Driver
[ 118.763] ABI class: X.Org XInput driver, version 24.1
[ 118.763] (II) Using input driver 'libinput' for 'LITE-ON Technology USB NetVista Full Width Keyboard.'
[ 118.763] (**) LITE-ON Technology USB NetVista Full Width Keyboard.: always reports core events
[ 118.763] (**) Option "Device" "/dev/input/event25"
[ 118.763] (**) Option "_source" "server/udev"
[ 118.766] (II) event25 - LITE-ON Technology USB NetVista Full Width Keyboard.: is tagged by udev as: Keyboard
[ 118.766] (II) event25 - LITE-ON Technology USB NetVista Full Width Keyboard.: device is a keyboard
[ 118.766] (II) event25 - LITE-ON Technology USB NetVista Full Width Keyboard.: device removed
[ 118.810] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:03:08.0/0000:08:00.1/usb1/1-2/1-2.4/1-2.4.4/1-2.4.4.3/1-2.4.4.3.1/1-2.4.4.3.1:1.0/0003:04B3:3025.000C/input/input40/event25"
[ 118.810] (II) XINPUT: Adding extended input device "LITE-ON Technology USB NetVista Full Width Keyboard." (type: KEYBOARD, id 6)
[ 118.812] (II) event25 - LITE-ON Technology USB NetVista Full Width Keyboard.: is tagged by udev as: Keyboard
[ 118.812] (II) event25 - LITE-ON Technology USB NetVista Full Width Keyboard.: device is a keyboard
[ 118.813] (II) config/udev: Adding input device Logitech G100s Optical Gaming Mouse (/dev/input/event28)
[ 118.813] (**) Logitech G100s Optical Gaming Mouse: Applying InputClass "libinput pointer catchall"
[ 118.813] (II) Using input driver 'libinput' for 'Logitech G100s Optical Gaming Mouse'
[ 118.813] (**) Logitech G100s Optical Gaming Mouse: always reports core events
[ 118.813] (**) Option "Device" "/dev/input/event28"
[ 118.813] (**) Option "_source" "server/udev"
[ 118.871] (II) event28 - Logitech G100s Optical Gaming Mouse: is tagged by udev as: Mouse
[ 118.871] (II) event28 - Logitech G100s Optical Gaming Mouse: device set to 1000 DPI
[ 118.872] (II) event28 - Logitech G100s Optical Gaming Mouse: device is a pointer
[ 118.872] (II) event28 - Logitech G100s Optical Gaming Mouse: device removed
[ 118.956] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:03:08.0/0000:08:00.1/usb1/1-2/1-2.4/1-2.4.4/1-2.4.4.3/1-2.4.4.3.2/1-2.4.4.3.2:1.0/0003:046D:C247.000D/input/input41/event28"
[ 118.956] (II) XINPUT: Adding extended input device "Logitech G100s Optical Gaming Mouse" (type: MOUSE, id 7)
[ 118.956] (**) Option "AccelerationScheme" "none"
[ 118.956] (**) Logitech G100s Optical Gaming Mouse: (accel) selected scheme none/0
[ 118.956] (**) Logitech G100s Optical Gaming Mouse: (accel) acceleration factor: 2.000
[ 118.956] (**) Logitech G100s Optical Gaming Mouse: (accel) acceleration threshold: 4
[ 119.015] (II) event28 - Logitech G100s Optical Gaming Mouse: is tagged by udev as: Mouse
[ 119.015] (II) event28 - Logitech G100s Optical Gaming Mouse: device set to 1000 DPI
[ 119.015] (II) event28 - Logitech G100s Optical Gaming Mouse: device is a pointer
[ 119.016] (II) config/udev: Adding input device Logitech G100s Optical Gaming Mouse (/dev/input/mouse2)
[ 119.016] (II) No input driver specified, ignoring this device.
[ 119.016] (II) This device may have been added with another device file.
[ 119.019] (II) config/udev: Adding input device LITE-ON Technology USB NetVista Full Width Keyboard. (/dev/input/event31)
[ 119.019] (**) LITE-ON Technology USB NetVista Full Width Keyboard.: Applying InputClass "libinput keyboard catchall"
[ 119.019] (II) Using input driver 'libinput' for 'LITE-ON Technology USB NetVista Full Width Keyboard.'
[ 119.019] (**) LITE-ON Technology USB NetVista Full Width Keyboard.: always reports core events
[ 119.019] (**) Option "Device" "/dev/input/event31"
[ 119.019] (**) Option "_source" "server/udev"
[ 119.019] (II) event31 - LITE-ON Technology USB NetVista Full Width Keyboard.: is tagged by udev as: Keyboard
[ 119.019] (II) event31 - LITE-ON Technology USB NetVista Full Width Keyboard.: device is a keyboard
[ 119.020] (II) event31 - LITE-ON Technology USB NetVista Full Width Keyboard.: device removed
[ 119.050] (**) Option "config_info" "udev:/sys/devices/virtual/input/input44/event31"
[ 119.050] (II) XINPUT: Adding extended input device "LITE-ON Technology USB NetVista Full Width Keyboard." (type: KEYBOARD, id 8)
[ 119.050] (II) event31 - LITE-ON Technology USB NetVista Full Width Keyboard.: is tagged by udev as: Keyboard
[ 119.050] (II) event31 - LITE-ON Technology USB NetVista Full Width Keyboard.: device is a keyboard
[ 127.271] (II) AMDGPU(0): EDID vendor "DEL", prod id 41145
[ 127.271] (II) AMDGPU(0): Using EDID range info for horizontal sync
[ 127.271] (II) AMDGPU(0): Using EDID range info for vertical refresh
[ 127.271] (II) AMDGPU(0): Printing DDC gathered Modelines:
[ 127.271] (II) AMDGPU(0): Modeline "1920x1200"x0.0 154.00 1920 1968 2000 2080 1200 1203 1209 1235 +hsync +vsync (74.0 kHz eP)
[ 127.271] (II) AMDGPU(0): Modeline "1920x1080"x0.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz e)
[ 127.271] (II) AMDGPU(0): Modeline "1920x1080i"x0.0 74.25 1920 2008 2052 2200 1080 1084 1094 1125 interlace +hsync +vsync (33.8 kHz e)
[ 127.271] (II) AMDGPU(0): Modeline "1280x720"x0.0 74.25 1280 1390 1430 1650 720 725 730 750 +hsync +vsync (45.0 kHz e)
[ 127.271] (II) AMDGPU(0): Modeline "720x480"x0.0 27.00 720 736 798 858 480 489 495 525 -hsync -vsync (31.5 kHz e)
[ 127.271] (II) AMDGPU(0): Modeline "1440x480i"x0.0 27.00 1440 1478 1602 1716 480 488 494 525 interlace -hsync -vsync (15.7 kHz e)
[ 127.271] (II) AMDGPU(0): Modeline "1440x576i"x0.0 27.00 1440 1464 1590 1728 576 580 586 625 interlace -hsync -vsync (15.6 kHz e)
[ 127.271] (II) AMDGPU(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 127.271] (II) AMDGPU(0): Modeline "1920x1080i"x0.0 74.25 1920 2448 2492 2640 1080 1084 1094 1125 interlace +hsync +vsync (28.1 kHz e)
[ 127.271] (II) AMDGPU(0): Modeline "1920x1080"x0.0 148.50 1920 2448 2492 2640 1080 1084 1089 1125 +hsync +vsync (56.2 kHz e)
[ 127.271] (II) AMDGPU(0): Modeline "720x576"x0.0 27.00 720 732 796 864 576 581 586 625 -hsync -vsync (31.2 kHz e)
[ 127.271] (II) AMDGPU(0): Modeline "1280x720"x0.0 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync (37.5 kHz e)
[ 127.271] (II) AMDGPU(0): Modeline "1920x1080"x0.0 74.25 1920 2558 2602 2750 1080 1084 1089 1125 +hsync +vsync (27.0 kHz e)
[ 127.271] (II) AMDGPU(0): Modeline "1920x1080"x0.0 74.25 1920 2448 2492 2640 1080 1084 1089 1125 +hsync +vsync (28.1 kHz e)
[ 127.271] (II) AMDGPU(0): Modeline "1920x1080"x0.0 74.25 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (33.8 kHz e)
[ 127.271] (II) AMDGPU(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 127.271] (II) AMDGPU(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 127.271] (II) AMDGPU(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 127.271] (II) AMDGPU(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[ 127.271] (II) AMDGPU(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz e)
[ 127.271] (II) AMDGPU(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 127.271] (II) AMDGPU(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 127.271] (II) AMDGPU(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 127.271] (II) AMDGPU(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[ 127.271] (II) AMDGPU(0): Modeline "1600x1200"x0.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz e)
[ 127.531] (EE) AMDGPU(0): drmmode_do_crtc_dpms cannot get last vblank counter
[ 127.531] (II) AMDGPU(0): Allocate new frame buffer 1920x1200
[ 127.532] (II) AMDGPU(0): => pitch 7680 bytes
[ 127.560] (II) AMDGPU(0): Allocate new frame buffer 3840x1200
[ 127.560] (II) AMDGPU(0): => pitch 15360 bytes
[ 309.900] (EE) event28 - Logitech G100s Optical Gaming Mouse: client bug: event processing lagging behind by 12ms, your system is too slow
[ 682.661] (EE) event28 - Logitech G100s Optical Gaming Mouse: client bug: event processing lagging behind by 18ms, your system is too slow
[ 879.108] (EE) event28 - Logitech G100s Optical Gaming Mouse: client bug: event processing lagging behind by 18ms, your system is too slow
[ 944.596] (EE) event28 - Logitech G100s Optical Gaming Mouse: client bug: event processing lagging behind by 14ms, your system is too slow
[ 1044.513] (EE) event31 - LITE-ON Technology USB NetVista Full Width Keyboard.: client bug: event processing lagging behind by 33ms, your system is too slow
[ 1044.696] (EE) event31 - LITE-ON Technology USB NetVista Full Width Keyboard.: client bug: event processing lagging behind by 33ms, your system is too slow
[ 1044.880] (EE) event31 - LITE-ON Technology USB NetVista Full Width Keyboard.: client bug: event processing lagging behind by 33ms, your system is too slow
[ 1045.063] (EE) event31 - LITE-ON Technology USB NetVista Full Width Keyboard.: client bug: event processing lagging behind by 33ms, your system is too slow
[ 1267.016] (EE) event28 - Logitech G100s Optical Gaming Mouse: client bug: event processing lagging behind by 16ms, your system is too slow
[ 1448.351] (EE) event28 - Logitech G100s Optical Gaming Mouse: client bug: event processing lagging behind by 17ms, your system is too slow
[ 1463.463] (EE) event28 - Logitech G100s Optical Gaming Mouse: client bug: event processing lagging behind by 15ms, your system is too slow
[ 1730.453] (EE) event28 - Logitech G100s Optical Gaming Mouse: client bug: event processing lagging behind by 16ms, your system is too slow
[ 1772.806] (EE) event31 - LITE-ON Technology USB NetVista Full Width Keyboard.: client bug: event processing lagging behind by 33ms, your system is too slow
[ 2304.732] (EE) event31 - LITE-ON Technology USB NetVista Full Width Keyboard.: client bug: event processing lagging behind by 19ms, your system is too slow
[ 2843.750] (EE) event28 - Logitech G100s Optical Gaming Mouse: client bug: event processing lagging behind by 14ms, your system is too slow
[ 2895.753] (EE) event31 - LITE-ON Technology USB NetVista Full Width Keyboard.: client bug: event processing lagging behind by 33ms, your system is too slow
[ 2895.936] (EE) event31 - LITE-ON Technology USB NetVista Full Width Keyboard.: client bug: event processing lagging behind by 33ms, your system is too slow
[ 2896.119] (EE) event31 - LITE-ON Technology USB NetVista Full Width Keyboard.: client bug: event processing lagging behind by 33ms, your system is too slowNote that the "event processing lagging behind" messages happen exactly during screen flickers.
dmesg with audit messages omited:
[ 0.000000] Linux version 5.8.13-arch1-1 (linux@archlinux) (gcc (GCC) 10.2.0, GNU ld (GNU Binutils) 2.35) #1 SMP PREEMPT Thu, 01 Oct 2020 20:40:35 +0000
[ 0.000000] Command line: BOOT_IMAGE=/root/boot/vmlinuz-linux root=/dev/mapper/gfr_crypt rw rootflags=subvol=root rd.luks.name=62f43f28-4668-44da-ac39-788721ef82c7=gfr_crypt rd.luks.key=/var/keys/self.key rd.luks.options=discard loglevel=4
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Hygon HygonGenuine
[ 0.000000] Centaur CentaurHauls
[ 0.000000] zhaoxin Shanghai
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
[ 0.000000] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256
[ 0.000000] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'compacted' format.
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009ffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000000a0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x0000000009e01fff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000009e02000-0x0000000009ffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000000a000000-0x000000000a1fffff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000a200000-0x000000000a20bfff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000000a20c000-0x00000000bb7d3fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000bb7d4000-0x00000000bb968fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000bb969000-0x00000000bbaecfff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000bbaed000-0x00000000bbf0afff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000bbf0b000-0x00000000bcaf5fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000bcaf6000-0x00000000bcb86fff] type 20
[ 0.000000] BIOS-e820: [mem 0x00000000bcb87000-0x00000000beffffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000bf000000-0x00000000bfffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fd000000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000103f37ffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] efi: EFI v2.70 by American Megatrends
[ 0.000000] efi: ACPI 2.0=0xbbe87000 ACPI=0xbbe87000 SMBIOS=0xbc9dd000 SMBIOS 3.0=0xbc9dc000 MEMATTR=0xb77a8018 ESRT=0xba47d698
[ 0.000000] SMBIOS 3.2.0 present.
[ 0.000000] DMI: Gigabyte Technology Co., Ltd. X570 UD/X570 UD, BIOS F12e 03/06/2020
[ 0.000000] tsc: Fast TSC calibration failed
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] last_pfn = 0x103f380 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF write-through
[ 0.000000] C0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000000 mask FFFF80000000 write-back
[ 0.000000] 1 base 000080000000 mask FFFFC0000000 write-back
[ 0.000000] 2 base 0000BC2D0000 mask FFFFFFFF0000 uncachable
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] TOM2: 0000001040000000 aka 66560M
[ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT
[ 0.000000] total RAM covered: 3071M
[ 0.000000] Found optimal setting for mtrr clean up
[ 0.000000] gran_size: 64K chunk_size: 64M num_reg: 3 lose cover RAM: 0G
[ 0.000000] e820: update [mem 0xbc2d0000-0xbc2dffff] usable ==> reserved
[ 0.000000] e820: update [mem 0xc0000000-0xffffffff] usable ==> reserved
[ 0.000000] last_pfn = 0xbf000 max_arch_pfn = 0x400000000
[ 0.000000] esrt: Reserving ESRT space from 0x00000000ba47d698 to 0x00000000ba47d6d0.
[ 0.000000] e820: update [mem 0xba47d000-0xba47dfff] usable ==> reserved
[ 0.000000] check: Scanning 1 areas for low memory corruption
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] Secure boot could not be determined
[ 0.000000] RAMDISK: [mem 0x362f3000-0x37170fff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000BBE87000 000024 (v02 ALASKA)
[ 0.000000] ACPI: XSDT 0x00000000BBE870A0 0000BC (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: FACP 0x00000000BBE8DFC0 000114 (v06 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: DSDT 0x00000000BBE871F0 006DCB (v02 ALASKA A M I 01072009 INTL 20160930)
[ 0.000000] ACPI: FACS 0x00000000BBEF3E00 000040
[ 0.000000] ACPI: APIC 0x00000000BBE8E0D8 00015E (v03 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: FPDT 0x00000000BBE8E238 000044 (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: FIDT 0x00000000BBE8E280 00009C (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: SSDT 0x00000000BBE8E320 0000FC (v02 ALASKA A M I 01072009 AMI 01072009)
[ 0.000000] ACPI: SSDT 0x00000000BBE8E420 008C98 (v02 ALASKA A M I 00000002 MSFT 04000000)
[ 0.000000] ACPI: SSDT 0x00000000BBE970B8 00374D (v01 ALASKA A M I 00000001 INTL 20160930)
[ 0.000000] ACPI: MCFG 0x00000000BBE9A808 00003C (v01 ALASKA A M I 01072009 MSFT 00010013)
[ 0.000000] ACPI: SSDT 0x00000000BBE9A848 00939D (v01 ALASKA A M I 00000001 INTL 20160930)
[ 0.000000] ACPI: HPET 0x00000000BBEA3BE8 000038 (v01 ALASKA A M I 01072009 AMI 00000005)
[ 0.000000] ACPI: SSDT 0x00000000BBEA3C20 000024 (v01 ALASKA A M I 00001000 INTL 20160930)
[ 0.000000] ACPI: UEFI 0x00000000BBEA3C48 000042 (v01 ALASKA A M I 00000002 01000013)
[ 0.000000] ACPI: BGRT 0x00000000BBEA3C90 000038 (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: PCCT 0x00000000BBEA3CC8 00006E (v01 ALASKA A M I 00000001 AMD 00000000)
[ 0.000000] ACPI: SSDT 0x00000000BBEA3D38 003EC9 (v01 ALASKA A M I 00000001 AMD 00000001)
[ 0.000000] ACPI: CRAT 0x00000000BBEA7C08 000ED8 (v01 ALASKA A M I 00000001 AMD 00000001)
[ 0.000000] ACPI: CDIT 0x00000000BBEA8AE0 000029 (v01 ALASKA A M I 00000001 AMD 00000001)
[ 0.000000] ACPI: SSDT 0x00000000BBEA8B10 001EC3 (v01 ALASKA A M I 00000001 INTL 20160930)
[ 0.000000] ACPI: WSMT 0x00000000BBEAA9D8 000028 (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000103f37ffff]
[ 0.000000] NODE_DATA(0) allocated [mem 0x103f37c000-0x103f37ffff]
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.000000] Normal [mem 0x0000000100000000-0x000000103f37ffff]
[ 0.000000] Device empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009ffff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x0000000009e01fff]
[ 0.000000] node 0: [mem 0x000000000a000000-0x000000000a1fffff]
[ 0.000000] node 0: [mem 0x000000000a20c000-0x00000000bb7d3fff]
[ 0.000000] node 0: [mem 0x00000000bb969000-0x00000000bbaecfff]
[ 0.000000] node 0: [mem 0x00000000bcb87000-0x00000000beffffff]
[ 0.000000] node 0: [mem 0x0000000100000000-0x000000103f37ffff]
[ 0.000000] Zeroed struct page in unavailable ranges: 12570 pages
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000103f37ffff]
[ 0.000000] On node 0 totalpages: 16764646
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 31 pages reserved
[ 0.000000] DMA zone: 3999 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 12080 pages used for memmap
[ 0.000000] DMA32 zone: 773063 pages, LIFO batch:63
[ 0.000000] Normal zone: 249806 pages used for memmap
[ 0.000000] Normal zone: 15987584 pages, LIFO batch:63
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[ 0.000000] IOAPIC[0]: apic_id 17, version 33, address 0xfec00000, GSI 0-23
[ 0.000000] IOAPIC[1]: apic_id 18, version 33, address 0xfec01000, GSI 24-55
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x10228201 base: 0xfed00000
[ 0.000000] e820: update [mem 0xb7c9d000-0xb7ce1fff] usable ==> reserved
[ 0.000000] smpboot: Allowing 32 CPUs, 16 hotplug CPUs
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0x000a0000-0x000fffff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0x09e02000-0x09ffffff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0x0a200000-0x0a20bfff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xb7c9d000-0xb7ce1fff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xba47d000-0xba47dfff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xbb7d4000-0xbb968fff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xbbaed000-0xbbf0afff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xbbf0b000-0xbcaf5fff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xbcaf6000-0xbcb86fff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xbf000000-0xbfffffff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xc0000000-0xf7ffffff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xfc000000-0xfcffffff]
[ 0.000000] PM: hibernation: Registered nosave memory: [mem 0xfd000000-0xffffffff]
[ 0.000000] [mem 0xc0000000-0xf7ffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370452778343963 ns
[ 0.000000] setup_percpu: NR_CPUS:320 nr_cpumask_bits:320 nr_cpu_ids:32 nr_node_ids:1
[ 0.000000] percpu: Embedded 56 pages/cpu s192512 r8192 d28672 u262144
[ 0.000000] pcpu-alloc: s192512 r8192 d28672 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 00 01 02 03 04 05 06 07 [0] 08 09 10 11 12 13 14 15
[ 0.000000] pcpu-alloc: [0] 16 17 18 19 20 21 22 23 [0] 24 25 26 27 28 29 30 31
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16502665
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/root/boot/vmlinuz-linux root=/dev/mapper/gfr_crypt rw rootflags=subvol=root rd.luks.name=62f43f28-4668-44da-ac39-788721ef82c7=gfr_crypt rd.luks.key=/var/keys/self.key rd.luks.options=discard loglevel=4
[ 0.000000] printk: log_buf_len individual max cpu contribution: 4096 bytes
[ 0.000000] printk: log_buf_len total cpu_extra contributions: 126976 bytes
[ 0.000000] printk: log_buf_len min size: 131072 bytes
[ 0.000000] printk: log_buf_len: 262144 bytes
[ 0.000000] printk: early log buf free: 119080(90%)
[ 0.000000] Dentry cache hash table entries: 8388608 (order: 14, 67108864 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 4194304 (order: 13, 33554432 bytes, linear)
[ 0.000000] mem auto-init: stack:byref_all, heap alloc:on, heap free:off
[ 0.000000] Memory: 65682748K/67058584K available (14339K kernel code, 1480K rwdata, 7916K rodata, 1644K init, 3024K bss, 1375836K reserved, 0K cma-reserved)
[ 0.000000] random: get_random_u64 called from __kmem_cache_create+0x3e/0x600 with crng_init=0
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=32, Nodes=1
[ 0.000000] ftrace: allocating 40118 entries in 157 pages
[ 0.000000] ftrace: allocated 157 pages with 5 groups
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=320 to nr_cpu_ids=32.
[ 0.000000] rcu: RCU priority boosting: priority 1 delay 500 ms.
[ 0.000000] Trampoline variant of Tasks RCU enabled.
[ 0.000000] Rude variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=32
[ 0.000000] NR_IRQS: 20736, nr_irqs: 1224, preallocated irqs: 16
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] printk: console [tty0] enabled
[ 0.000000] ACPI: Core revision 20200528
[ 0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484873504 ns
[ 0.000000] APIC: Switch to symmetric I/O mode setup
[ 0.000000] Switched APIC routing to physical flat.
[ 0.000000] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.023333] tsc: PIT calibration matches HPET. 2 loops
[ 0.023333] tsc: Detected 3892.847 MHz processor
[ 0.000002] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x7039ec55537, max_idle_ns: 881590793530 ns
[ 0.000003] Calibrating delay loop (skipped), value calculated using timer frequency.. 7788.09 BogoMIPS (lpj=12976156)
[ 0.000004] pid_max: default: 32768 minimum: 301
[ 0.002820] LSM: Security Framework initializing
[ 0.002822] Yama: becoming mindful.
[ 0.002900] Mount-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.002968] Mountpoint-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.003119] x86/cpu: User Mode Instruction Prevention (UMIP) activated
[ 0.003169] LVT offset 1 assigned for vector 0xf9
[ 0.003296] LVT offset 2 assigned for vector 0xf4
[ 0.003359] Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 512
[ 0.003360] Last level dTLB entries: 4KB 2048, 2MB 2048, 4MB 1024, 1GB 0
[ 0.003361] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
[ 0.003362] Spectre V2 : Mitigation: Full AMD retpoline
[ 0.003362] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[ 0.003363] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier
[ 0.003364] Spectre V2 : User space: Mitigation: STIBP via seccomp and prctl
[ 0.003364] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl and seccomp
[ 0.003525] Freeing SMP alternatives memory: 32K
[ 0.110884] smpboot: CPU0: AMD Ryzen 7 3800X 8-Core Processor (family: 0x17, model: 0x71, stepping: 0x0)
[ 0.110937] Performance Events: Fam17h+ core perfctr, AMD PMU driver.
[ 0.110939] ... version: 0
[ 0.110939] ... bit width: 48
[ 0.110940] ... generic registers: 6
[ 0.110940] ... value mask: 0000ffffffffffff
[ 0.110940] ... max period: 00007fffffffffff
[ 0.110940] ... fixed-purpose events: 0
[ 0.110941] ... event mask: 000000000000003f
[ 0.110961] rcu: Hierarchical SRCU implementation.
[ 0.111260] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[ 0.111399] smp: Bringing up secondary CPUs ...
[ 0.111459] x86: Booting SMP configuration:
[ 0.111459] .... node #0, CPUs: #1 #2 #3 #4 #5 #6 #7 #8 #9 #10 #11 #12 #13 #14 #15
[ 0.143378] smp: Brought up 1 node, 16 CPUs
[ 0.143378] smpboot: Max logical packages: 2
[ 0.143378] smpboot: Total of 16 processors activated (124620.56 BogoMIPS)
[ 0.147296] devtmpfs: initialized
[ 0.147296] x86/mm: Memory block size: 128MB
[ 0.148559] PM: Registering ACPI NVS region [mem 0x0a200000-0x0a20bfff] (49152 bytes)
[ 0.148559] PM: Registering ACPI NVS region [mem 0xbbaed000-0xbbf0afff] (4317184 bytes)
[ 0.150008] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[ 0.150034] futex hash table entries: 8192 (order: 7, 524288 bytes, linear)
[ 0.150109] pinctrl core: initialized pinctrl subsystem
[ 0.150167] PM: RTC time: 08:16:32, date: 2020-10-08
[ 0.150170] thermal_sys: Registered thermal governor 'fair_share'
[ 0.150170] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.150170] thermal_sys: Registered thermal governor 'step_wise'
[ 0.150171] thermal_sys: Registered thermal governor 'user_space'
[ 0.150171] thermal_sys: Registered thermal governor 'power_allocator'
[ 0.150274] NET: Registered protocol family 16
[ 0.150512] DMA: preallocated 4096 KiB GFP_KERNEL pool for atomic allocations
[ 0.150700] DMA: preallocated 4096 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.150901] DMA: preallocated 4096 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.150912] cpuidle: using governor ladder
[ 0.150912] cpuidle: using governor menu
[ 0.150912] Detected 1 PCC Subspaces
[ 0.150912] Registering PCC driver as Mailbox controller
[ 0.150912] ACPI: bus type PCI registered
[ 0.150912] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.150912] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[ 0.150912] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[ 0.150912] PCI: Using configuration type 1 for base access
[ 0.150912] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[ 0.150912] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.153438] ACPI: Added _OSI(Module Device)
[ 0.153439] ACPI: Added _OSI(Processor Device)
[ 0.153439] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.153440] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.153441] ACPI: Added _OSI(Linux-Dell-Video)
[ 0.153441] ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio)
[ 0.153442] ACPI: Added _OSI(Linux-HPI-Hybrid-Graphics)
[ 0.162279] ACPI: 8 ACPI AML tables successfully acquired and loaded
[ 0.163705] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[ 0.172210] ACPI: Interpreter enabled
[ 0.172221] ACPI: (supports S0 S3 S4 S5)
[ 0.172222] ACPI: Using IOAPIC for interrupt routing
[ 0.172478] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.172698] ACPI: Enabled 2 GPEs in block 00 to 1F
[ 0.181442] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.181442] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI EDR HPX-Type3]
[ 0.181442] acpi PNP0A08:00: _OSC: platform does not support [SHPCHotplug LTR DPC]
[ 0.181442] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
[ 0.181442] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
[ 0.181442] PCI host bridge to bus 0000:00
[ 0.181442] pci_bus 0000:00: root bus resource [io 0x0000-0x03af window]
[ 0.181442] pci_bus 0000:00: root bus resource [io 0x03e0-0x0cf7 window]
[ 0.181442] pci_bus 0000:00: root bus resource [io 0x03b0-0x03df window]
[ 0.181442] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.181442] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[ 0.181442] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff window]
[ 0.181442] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xfec02fff window]
[ 0.181442] pci_bus 0000:00: root bus resource [mem 0xfee00000-0xffffffff window]
[ 0.181442] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.181442] pci 0000:00:00.0: [1022:1480] type 00 class 0x060000
[ 0.181442] pci 0000:00:01.0: [1022:1482] type 00 class 0x060000
[ 0.181442] pci 0000:00:01.1: [1022:1483] type 01 class 0x060400
[ 0.181442] pci 0000:00:01.1: enabling Extended Tags
[ 0.181442] pci 0000:00:01.1: PME# supported from D0 D3hot D3cold
[ 0.181442] pci 0000:00:01.2: [1022:1483] type 01 class 0x060400
[ 0.181442] pci 0000:00:01.2: enabling Extended Tags
[ 0.181442] pci 0000:00:01.2: PME# supported from D0 D3hot D3cold
[ 0.181442] pci 0000:00:02.0: [1022:1482] type 00 class 0x060000
[ 0.181442] pci 0000:00:03.0: [1022:1482] type 00 class 0x060000
[ 0.181442] pci 0000:00:03.1: [1022:1483] type 01 class 0x060400
[ 0.181442] pci 0000:00:03.1: PME# supported from D0 D3hot D3cold
[ 0.181442] pci 0000:00:04.0: [1022:1482] type 00 class 0x060000
[ 0.181442] pci 0000:00:05.0: [1022:1482] type 00 class 0x060000
[ 0.181516] pci 0000:00:07.0: [1022:1482] type 00 class 0x060000
[ 0.181583] pci 0000:00:07.1: [1022:1484] type 01 class 0x060400
[ 0.181611] pci 0000:00:07.1: enabling Extended Tags
[ 0.181647] pci 0000:00:07.1: PME# supported from D0 D3hot D3cold
[ 0.181737] pci 0000:00:08.0: [1022:1482] type 00 class 0x060000
[ 0.181803] pci 0000:00:08.1: [1022:1484] type 01 class 0x060400
[ 0.181834] pci 0000:00:08.1: enabling Extended Tags
[ 0.181873] pci 0000:00:08.1: PME# supported from D0 D3hot D3cold
[ 0.181961] pci 0000:00:08.2: [1022:1484] type 01 class 0x060400
[ 0.181991] pci 0000:00:08.2: enabling Extended Tags
[ 0.182032] pci 0000:00:08.2: PME# supported from D0 D3hot D3cold
[ 0.182121] pci 0000:00:08.3: [1022:1484] type 01 class 0x060400
[ 0.182152] pci 0000:00:08.3: enabling Extended Tags
[ 0.182191] pci 0000:00:08.3: PME# supported from D0 D3hot D3cold
[ 0.182295] pci 0000:00:14.0: [1022:790b] type 00 class 0x0c0500
[ 0.182412] pci 0000:00:14.3: [1022:790e] type 00 class 0x060100
[ 0.182532] pci 0000:00:18.0: [1022:1440] type 00 class 0x060000
[ 0.182577] pci 0000:00:18.1: [1022:1441] type 00 class 0x060000
[ 0.182621] pci 0000:00:18.2: [1022:1442] type 00 class 0x060000
[ 0.182665] pci 0000:00:18.3: [1022:1443] type 00 class 0x060000
[ 0.182709] pci 0000:00:18.4: [1022:1444] type 00 class 0x060000
[ 0.182753] pci 0000:00:18.5: [1022:1445] type 00 class 0x060000
[ 0.182797] pci 0000:00:18.6: [1022:1446] type 00 class 0x060000
[ 0.182843] pci 0000:00:18.7: [1022:1447] type 00 class 0x060000
[ 0.182932] pci 0000:01:00.0: [144d:a808] type 00 class 0x010802
[ 0.182959] pci 0000:01:00.0: reg 0x10: [mem 0xfcf00000-0xfcf03fff 64bit]
[ 0.183155] pci 0000:00:01.1: PCI bridge to [bus 01]
[ 0.183160] pci 0000:00:01.1: bridge window [mem 0xfcf00000-0xfcffffff]
[ 0.183202] pci 0000:02:00.0: [1022:57ad] type 01 class 0x060400
[ 0.183270] pci 0000:02:00.0: enabling Extended Tags
[ 0.183353] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 0.183444] pci 0000:02:00.0: 63.012 Gb/s available PCIe bandwidth, limited by 16.0 GT/s PCIe x4 link at 0000:00:01.2 (capable of 126.024 Gb/s with 16.0 GT/s PCIe x8 link)
[ 0.183509] pci 0000:00:01.2: PCI bridge to [bus 02-0a]
[ 0.183512] pci 0000:00:01.2: bridge window [io 0xd000-0xefff]
[ 0.183513] pci 0000:00:01.2: bridge window [mem 0xfc100000-0xfc7fffff]
[ 0.183516] pci 0000:00:01.2: bridge window [mem 0xe0000000-0xf01fffff 64bit pref]
[ 0.183740] pci 0000:03:02.0: [1022:57a3] type 01 class 0x060400
[ 0.183832] pci 0000:03:02.0: enabling Extended Tags
[ 0.184003] pci 0000:03:02.0: PME# supported from D0 D3hot D3cold
[ 0.184186] pci 0000:03:04.0: [1022:57a3] type 01 class 0x060400
[ 0.184279] pci 0000:03:04.0: enabling Extended Tags
[ 0.184449] pci 0000:03:04.0: PME# supported from D0 D3hot D3cold
[ 0.184670] pci 0000:03:08.0: [1022:57a4] type 01 class 0x060400
[ 0.184760] pci 0000:03:08.0: enabling Extended Tags
[ 0.184914] pci 0000:03:08.0: PME# supported from D0 D3hot D3cold
[ 0.185083] pci 0000:03:09.0: [1022:57a4] type 01 class 0x060400
[ 0.185175] pci 0000:03:09.0: enabling Extended Tags
[ 0.185329] pci 0000:03:09.0: PME# supported from D0 D3hot D3cold
[ 0.185489] pci 0000:03:0a.0: [1022:57a4] type 01 class 0x060400
[ 0.185580] pci 0000:03:0a.0: enabling Extended Tags
[ 0.185734] pci 0000:03:0a.0: PME# supported from D0 D3hot D3cold
[ 0.185922] pci 0000:02:00.0: PCI bridge to [bus 03-0a]
[ 0.185927] pci 0000:02:00.0: bridge window [io 0xd000-0xefff]
[ 0.185930] pci 0000:02:00.0: bridge window [mem 0xfc100000-0xfc7fffff]
[ 0.185936] pci 0000:02:00.0: bridge window [mem 0xe0000000-0xf01fffff 64bit pref]
[ 0.186030] pci 0000:04:00.0: [1002:1478] type 01 class 0x060400
[ 0.186071] pci 0000:04:00.0: reg 0x10: [mem 0xfc400000-0xfc403fff]
[ 0.186121] pci 0000:04:00.0: enabling Extended Tags
[ 0.186236] pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
[ 0.186349] pci 0000:04:00.0: 63.012 Gb/s available PCIe bandwidth, limited by 16.0 GT/s PCIe x4 link at 0000:00:01.2 (capable of 252.048 Gb/s with 16.0 GT/s PCIe x16 link)
[ 0.186441] pci 0000:03:02.0: PCI bridge to [bus 04-06]
[ 0.186447] pci 0000:03:02.0: bridge window [io 0xe000-0xefff]
[ 0.186450] pci 0000:03:02.0: bridge window [mem 0xfc300000-0xfc4fffff]
[ 0.186456] pci 0000:03:02.0: bridge window [mem 0xe0000000-0xf01fffff 64bit pref]
[ 0.186514] pci 0000:05:00.0: [1002:1479] type 01 class 0x060400
[ 0.186605] pci 0000:05:00.0: enabling Extended Tags
[ 0.186719] pci 0000:05:00.0: PME# supported from D0 D3hot D3cold
[ 0.186884] pci 0000:04:00.0: PCI bridge to [bus 05-06]
[ 0.186891] pci 0000:04:00.0: bridge window [io 0xe000-0xefff]
[ 0.186894] pci 0000:04:00.0: bridge window [mem 0xfc300000-0xfc3fffff]
[ 0.186901] pci 0000:04:00.0: bridge window [mem 0xe0000000-0xf01fffff 64bit pref]
[ 0.186960] pci 0000:06:00.0: [1002:731f] type 00 class 0x030000
[ 0.187012] pci 0000:06:00.0: reg 0x10: [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.187027] pci 0000:06:00.0: reg 0x18: [mem 0xf0000000-0xf01fffff 64bit pref]
[ 0.187036] pci 0000:06:00.0: reg 0x20: [io 0xe000-0xe0ff]
[ 0.187045] pci 0000:06:00.0: reg 0x24: [mem 0xfc300000-0xfc37ffff]
[ 0.187053] pci 0000:06:00.0: reg 0x30: [mem 0xfc380000-0xfc39ffff pref]
[ 0.187064] pci 0000:06:00.0: enabling Extended Tags
[ 0.187212] pci 0000:06:00.0: PME# supported from D1 D2 D3hot D3cold
[ 0.187349] pci 0000:06:00.0: 63.012 Gb/s available PCIe bandwidth, limited by 16.0 GT/s PCIe x4 link at 0000:00:01.2 (capable of 252.048 Gb/s with 16.0 GT/s PCIe x16 link)
[ 0.187388] pci 0000:06:00.1: [1002:ab38] type 00 class 0x040300
[ 0.187423] pci 0000:06:00.1: reg 0x10: [mem 0xfc3a0000-0xfc3a3fff]
[ 0.187501] pci 0000:06:00.1: enabling Extended Tags
[ 0.187591] pci 0000:06:00.1: PME# supported from D1 D2 D3hot D3cold
[ 0.187769] pci 0000:05:00.0: PCI bridge to [bus 06]
[ 0.187776] pci 0000:05:00.0: bridge window [io 0xe000-0xefff]
[ 0.187780] pci 0000:05:00.0: bridge window [mem 0xfc300000-0xfc3fffff]
[ 0.187787] pci 0000:05:00.0: bridge window [mem 0xe0000000-0xf01fffff 64bit pref]
[ 0.187903] pci 0000:07:00.0: [10ec:8168] type 00 class 0x020000
[ 0.187943] pci 0000:07:00.0: reg 0x10: [io 0xd000-0xd0ff]
[ 0.187979] pci 0000:07:00.0: reg 0x18: [mem 0xfc704000-0xfc704fff 64bit]
[ 0.188000] pci 0000:07:00.0: reg 0x20: [mem 0xfc700000-0xfc703fff 64bit]
[ 0.188139] pci 0000:07:00.0: supports D1 D2
[ 0.188140] pci 0000:07:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.188342] pci 0000:03:04.0: PCI bridge to [bus 07]
[ 0.188348] pci 0000:03:04.0: bridge window [io 0xd000-0xdfff]
[ 0.188351] pci 0000:03:04.0: bridge window [mem 0xfc700000-0xfc7fffff]
[ 0.188465] pci 0000:08:00.0: [1022:1485] type 00 class 0x130000
[ 0.188545] pci 0000:08:00.0: enabling Extended Tags
[ 0.188693] pci 0000:08:00.0: 63.012 Gb/s available PCIe bandwidth, limited by 16.0 GT/s PCIe x4 link at 0000:00:01.2 (capable of 252.048 Gb/s with 16.0 GT/s PCIe x16 link)
[ 0.188822] pci 0000:08:00.1: [1022:149c] type 00 class 0x0c0330
[ 0.189187] pci 0000:08:00.1: reg 0x10: [mem 0xfc200000-0xfc2fffff 64bit]
[ 0.189939] pci 0000:08:00.1: enabling Extended Tags
[ 0.190453] pci 0000:08:00.1: PME# supported from D0 D3hot D3cold
[ 0.190767] pci 0000:08:00.3: [1022:149c] type 00 class 0x0c0330
[ 0.190800] pci 0000:08:00.3: reg 0x10: [mem 0xfc100000-0xfc1fffff 64bit]
[ 0.190859] pci 0000:08:00.3: enabling Extended Tags
[ 0.190934] pci 0000:08:00.3: PME# supported from D0 D3hot D3cold
[ 0.191080] pci 0000:03:08.0: PCI bridge to [bus 08]
[ 0.191088] pci 0000:03:08.0: bridge window [mem 0xfc100000-0xfc2fffff]
[ 0.191179] pci 0000:09:00.0: [1022:7901] type 00 class 0x010601
[ 0.191262] pci 0000:09:00.0: reg 0x24: [mem 0xfc600000-0xfc6007ff]
[ 0.191281] pci 0000:09:00.0: enabling Extended Tags
[ 0.191373] pci 0000:09:00.0: PME# supported from D3hot D3cold
[ 0.191446] pci 0000:09:00.0: 63.012 Gb/s available PCIe bandwidth, limited by 16.0 GT/s PCIe x4 link at 0000:00:01.2 (capable of 252.048 Gb/s with 16.0 GT/s PCIe x16 link)
[ 0.191516] pci 0000:03:09.0: PCI bridge to [bus 09]
[ 0.191524] pci 0000:03:09.0: bridge window [mem 0xfc600000-0xfc6fffff]
[ 0.191627] pci 0000:0a:00.0: [1022:7901] type 00 class 0x010601
[ 0.191710] pci 0000:0a:00.0: reg 0x24: [mem 0xfc500000-0xfc5007ff]
[ 0.191729] pci 0000:0a:00.0: enabling Extended Tags
[ 0.191822] pci 0000:0a:00.0: PME# supported from D3hot D3cold
[ 0.191895] pci 0000:0a:00.0: 63.012 Gb/s available PCIe bandwidth, limited by 16.0 GT/s PCIe x4 link at 0000:00:01.2 (capable of 252.048 Gb/s with 16.0 GT/s PCIe x16 link)
[ 0.191964] pci 0000:03:0a.0: PCI bridge to [bus 0a]
[ 0.191973] pci 0000:03:0a.0: bridge window [mem 0xfc500000-0xfc5fffff]
[ 0.192050] pci 0000:0b:00.0: [1002:1478] type 01 class 0x060400
[ 0.192073] pci 0000:0b:00.0: reg 0x10: [mem 0xfcc00000-0xfcc03fff]
[ 0.192161] pci 0000:0b:00.0: PME# supported from D0 D3hot D3cold
[ 0.192265] pci 0000:00:03.1: PCI bridge to [bus 0b-0d]
[ 0.192268] pci 0000:00:03.1: bridge window [io 0xf000-0xffff]
[ 0.192269] pci 0000:00:03.1: bridge window [mem 0xfcb00000-0xfccfffff]
[ 0.192272] pci 0000:00:03.1: bridge window [mem 0xc0000000-0xd01fffff 64bit pref]
[ 0.192306] pci 0000:0c:00.0: [1002:1479] type 01 class 0x060400
[ 0.192413] pci 0000:0c:00.0: PME# supported from D0 D3hot D3cold
[ 0.192504] pci 0000:0b:00.0: PCI bridge to [bus 0c-0d]
[ 0.192508] pci 0000:0b:00.0: bridge window [io 0xf000-0xffff]
[ 0.192510] pci 0000:0b:00.0: bridge window [mem 0xfcb00000-0xfcbfffff]
[ 0.192514] pci 0000:0b:00.0: bridge window [mem 0xc0000000-0xd01fffff 64bit pref]
[ 0.192548] pci 0000:0d:00.0: [1002:731f] type 00 class 0x030000
[ 0.192578] pci 0000:0d:00.0: reg 0x10: [mem 0xc0000000-0xcfffffff 64bit pref]
[ 0.192588] pci 0000:0d:00.0: reg 0x18: [mem 0xd0000000-0xd01fffff 64bit pref]
[ 0.192595] pci 0000:0d:00.0: reg 0x20: [io 0xf000-0xf0ff]
[ 0.192602] pci 0000:0d:00.0: reg 0x24: [mem 0xfcb00000-0xfcb7ffff]
[ 0.192609] pci 0000:0d:00.0: reg 0x30: [mem 0xfcb80000-0xfcb9ffff pref]
[ 0.192621] pci 0000:0d:00.0: BAR 0: assigned to efifb
[ 0.192691] pci 0000:0d:00.0: PME# supported from D1 D2 D3hot D3cold
[ 0.192787] pci 0000:0d:00.1: [1002:ab38] type 00 class 0x040300
[ 0.192806] pci 0000:0d:00.1: reg 0x10: [mem 0xfcba0000-0xfcba3fff]
[ 0.192894] pci 0000:0d:00.1: PME# supported from D1 D2 D3hot D3cold
[ 0.192995] pci 0000:0c:00.0: PCI bridge to [bus 0d]
[ 0.192999] pci 0000:0c:00.0: bridge window [io 0xf000-0xffff]
[ 0.193001] pci 0000:0c:00.0: bridge window [mem 0xfcb00000-0xfcbfffff]
[ 0.193005] pci 0000:0c:00.0: bridge window [mem 0xc0000000-0xd01fffff 64bit pref]
[ 0.193051] pci 0000:0e:00.0: [1022:148a] type 00 class 0x130000
[ 0.193084] pci 0000:0e:00.0: enabling Extended Tags
[ 0.193187] pci 0000:00:07.1: PCI bridge to [bus 0e]
[ 0.193234] pci 0000:0f:00.0: [1022:1485] type 00 class 0x130000
[ 0.193274] pci 0000:0f:00.0: enabling Extended Tags
[ 0.193380] pci 0000:0f:00.1: [1022:1486] type 00 class 0x108000
[ 0.193401] pci 0000:0f:00.1: reg 0x18: [mem 0xfc900000-0xfc9fffff]
[ 0.193412] pci 0000:0f:00.1: reg 0x24: [mem 0xfca08000-0xfca09fff]
[ 0.193420] pci 0000:0f:00.1: enabling Extended Tags
[ 0.193506] pci 0000:0f:00.3: [1022:149c] type 00 class 0x0c0330
[ 0.193525] pci 0000:0f:00.3: reg 0x10: [mem 0xfc800000-0xfc8fffff 64bit]
[ 0.193553] pci 0000:0f:00.3: enabling Extended Tags
[ 0.193597] pci 0000:0f:00.3: PME# supported from D0 D3hot D3cold
[ 0.193657] pci 0000:0f:00.4: [1022:1487] type 00 class 0x040300
[ 0.193671] pci 0000:0f:00.4: reg 0x10: [mem 0xfca00000-0xfca07fff]
[ 0.193696] pci 0000:0f:00.4: enabling Extended Tags
[ 0.193737] pci 0000:0f:00.4: PME# supported from D0 D3hot D3cold
[ 0.193820] pci 0000:00:08.1: PCI bridge to [bus 0f]
[ 0.193823] pci 0000:00:08.1: bridge window [mem 0xfc800000-0xfcafffff]
[ 0.193861] pci 0000:10:00.0: [1022:7901] type 00 class 0x010601
[ 0.193903] pci 0000:10:00.0: reg 0x24: [mem 0xfce00000-0xfce007ff]
[ 0.193912] pci 0000:10:00.0: enabling Extended Tags
[ 0.193965] pci 0000:10:00.0: PME# supported from D3hot D3cold
[ 0.194055] pci 0000:00:08.2: PCI bridge to [bus 10]
[ 0.194058] pci 0000:00:08.2: bridge window [mem 0xfce00000-0xfcefffff]
[ 0.194097] pci 0000:11:00.0: [1022:7901] type 00 class 0x010601
[ 0.194139] pci 0000:11:00.0: reg 0x24: [mem 0xfcd00000-0xfcd007ff]
[ 0.194148] pci 0000:11:00.0: enabling Extended Tags
[ 0.194200] pci 0000:11:00.0: PME# supported from D3hot D3cold
[ 0.194287] pci 0000:00:08.3: PCI bridge to [bus 11]
[ 0.194291] pci 0000:00:08.3: bridge window [mem 0xfcd00000-0xfcdfffff]
[ 0.194523] ACPI: PCI Interrupt Link [LNKA] (IRQs 4 5 7 10 11 14 15) *0
[ 0.194568] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 5 7 10 11 14 15) *0
[ 0.194603] ACPI: PCI Interrupt Link [LNKC] (IRQs 4 5 7 10 11 14 15) *0
[ 0.194647] ACPI: PCI Interrupt Link [LNKD] (IRQs 4 5 7 10 11 14 15) *0
[ 0.194686] ACPI: PCI Interrupt Link [LNKE] (IRQs 4 5 7 10 11 14 15) *0
[ 0.194718] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 7 10 11 14 15) *0
[ 0.194750] ACPI: PCI Interrupt Link [LNKG] (IRQs 4 5 7 10 11 14 15) *0
[ 0.194782] ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 7 10 11 14 15) *0
[ 0.196671] iommu: Default domain type: Translated
[ 0.196687] pci 0000:06:00.0: vgaarb: VGA device added: decodes=io+mem,owns=none,locks=none
[ 0.196687] pci 0000:0d:00.0: vgaarb: setting as boot VGA device
[ 0.196687] pci 0000:0d:00.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[ 0.196687] pci 0000:06:00.0: vgaarb: bridge control possible
[ 0.196687] pci 0000:0d:00.0: vgaarb: bridge control possible
[ 0.196687] vgaarb: loaded
[ 0.196790] SCSI subsystem initialized
[ 0.196807] libata version 3.00 loaded.
[ 0.196807] ACPI: bus type USB registered
[ 0.196807] usbcore: registered new interface driver usbfs
[ 0.196807] usbcore: registered new interface driver hub
[ 0.196807] usbcore: registered new device driver usb
[ 0.196807] pps_core: LinuxPPS API ver. 1 registered
[ 0.196807] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.196807] PTP clock support registered
[ 0.196807] EDAC MC: Ver: 3.0.0
[ 0.196831] Registered efivars operations
[ 0.196831] NetLabel: Initializing
[ 0.196831] NetLabel: domain hash size = 128
[ 0.196831] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 0.196831] NetLabel: unlabeled traffic allowed by default
[ 0.196831] PCI: Using ACPI for IRQ routing
[ 0.198277] PCI: pci_cache_line_size set to 64 bytes
[ 0.198394] Expanded resource Reserved due to conflict with PCI Bus 0000:00
[ 0.198395] e820: reserve RAM buffer [mem 0x09e02000-0x0bffffff]
[ 0.198395] e820: reserve RAM buffer [mem 0x0a200000-0x0bffffff]
[ 0.198396] e820: reserve RAM buffer [mem 0xb7c9d000-0xb7ffffff]
[ 0.198396] e820: reserve RAM buffer [mem 0xba47d000-0xbbffffff]
[ 0.198397] e820: reserve RAM buffer [mem 0xbb7d4000-0xbbffffff]
[ 0.198397] e820: reserve RAM buffer [mem 0xbbaed000-0xbbffffff]
[ 0.198398] e820: reserve RAM buffer [mem 0xbf000000-0xbfffffff]
[ 0.198398] e820: reserve RAM buffer [mem 0x103f380000-0x103fffffff]
[ 0.198401] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.198401] hpet0: 3 comparators, 32-bit 14.318180 MHz counter
[ 0.200054] clocksource: Switched to clocksource tsc-early
[ 0.206775] VFS: Disk quotas dquot_6.6.0
[ 0.206786] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.206825] pnp: PnP ACPI init
[ 0.206888] system 00:00: [mem 0xf8000000-0xfbffffff] has been reserved
[ 0.206890] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.206911] system 00:01: [mem 0xfeb80000-0xfebfffff] has been reserved
[ 0.206912] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.206971] system 00:02: [mem 0xfd000000-0xfd0fffff] has been reserved
[ 0.206972] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.206998] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.207108] system 00:04: [io 0x0a00-0x0a2f] has been reserved
[ 0.207109] system 00:04: [io 0x0a30-0x0a3f] has been reserved
[ 0.207109] system 00:04: [io 0x0a40-0x0a4f] has been reserved
[ 0.207111] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.207293] system 00:05: [io 0x04d0-0x04d1] has been reserved
[ 0.207294] system 00:05: [io 0x040b] has been reserved
[ 0.207295] system 00:05: [io 0x04d6] has been reserved
[ 0.207295] system 00:05: [io 0x0c00-0x0c01] has been reserved
[ 0.207296] system 00:05: [io 0x0c14] has been reserved
[ 0.207297] system 00:05: [io 0x0c50-0x0c51] has been reserved
[ 0.207297] system 00:05: [io 0x0c52] has been reserved
[ 0.207298] system 00:05: [io 0x0c6c] has been reserved
[ 0.207299] system 00:05: [io 0x0c6f] has been reserved
[ 0.207299] system 00:05: [io 0x0cd0-0x0cd1] has been reserved
[ 0.207300] system 00:05: [io 0x0cd2-0x0cd3] has been reserved
[ 0.207300] system 00:05: [io 0x0cd4-0x0cd5] has been reserved
[ 0.207301] system 00:05: [io 0x0cd6-0x0cd7] has been reserved
[ 0.207302] system 00:05: [io 0x0cd8-0x0cdf] has been reserved
[ 0.207302] system 00:05: [io 0x0800-0x089f] has been reserved
[ 0.207303] system 00:05: [io 0x0b00-0x0b0f] has been reserved
[ 0.207304] system 00:05: [io 0x0b20-0x0b3f] has been reserved
[ 0.207304] system 00:05: [io 0x0900-0x090f] has been reserved
[ 0.207305] system 00:05: [io 0x0910-0x091f] has been reserved
[ 0.207306] system 00:05: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.207307] system 00:05: [mem 0xfec01000-0xfec01fff] could not be reserved
[ 0.207307] system 00:05: [mem 0xfedc0000-0xfedc0fff] has been reserved
[ 0.207308] system 00:05: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.207309] system 00:05: [mem 0xfed80000-0xfed8ffff] could not be reserved
[ 0.207309] system 00:05: [mem 0xfec10000-0xfec10fff] has been reserved
[ 0.207310] system 00:05: [mem 0xff000000-0xffffffff] has been reserved
[ 0.207312] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.207611] pnp: PnP ACPI: found 6 devices
[ 0.212849] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[ 0.212888] NET: Registered protocol family 2
[ 0.213005] tcp_listen_portaddr_hash hash table entries: 32768 (order: 7, 524288 bytes, linear)
[ 0.213286] TCP established hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 0.213715] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear)
[ 0.213776] TCP: Hash tables configured (established 524288 bind 65536)
[ 0.213921] UDP hash table entries: 32768 (order: 8, 1048576 bytes, linear)
[ 0.214037] UDP-Lite hash table entries: 32768 (order: 8, 1048576 bytes, linear)
[ 0.214144] NET: Registered protocol family 1
[ 0.214147] NET: Registered protocol family 44
[ 0.214204] pci 0000:00:01.1: PCI bridge to [bus 01]
[ 0.214207] pci 0000:00:01.1: bridge window [mem 0xfcf00000-0xfcffffff]
[ 0.214212] pci 0000:05:00.0: PCI bridge to [bus 06]
[ 0.214214] pci 0000:05:00.0: bridge window [io 0xe000-0xefff]
[ 0.214220] pci 0000:05:00.0: bridge window [mem 0xfc300000-0xfc3fffff]
[ 0.214224] pci 0000:05:00.0: bridge window [mem 0xe0000000-0xf01fffff 64bit pref]
[ 0.214231] pci 0000:04:00.0: PCI bridge to [bus 05-06]
[ 0.214233] pci 0000:04:00.0: bridge window [io 0xe000-0xefff]
[ 0.214239] pci 0000:04:00.0: bridge window [mem 0xfc300000-0xfc3fffff]
[ 0.214243] pci 0000:04:00.0: bridge window [mem 0xe0000000-0xf01fffff 64bit pref]
[ 0.214250] pci 0000:03:02.0: PCI bridge to [bus 04-06]
[ 0.214251] pci 0000:03:02.0: bridge window [io 0xe000-0xefff]
[ 0.214256] pci 0000:03:02.0: bridge window [mem 0xfc300000-0xfc4fffff]
[ 0.214259] pci 0000:03:02.0: bridge window [mem 0xe0000000-0xf01fffff 64bit pref]
[ 0.214265] pci 0000:03:04.0: PCI bridge to [bus 07]
[ 0.214267] pci 0000:03:04.0: bridge window [io 0xd000-0xdfff]
[ 0.214272] pci 0000:03:04.0: bridge window [mem 0xfc700000-0xfc7fffff]
[ 0.214280] pci 0000:03:08.0: PCI bridge to [bus 08]
[ 0.214285] pci 0000:03:08.0: bridge window [mem 0xfc100000-0xfc2fffff]
[ 0.214294] pci 0000:03:09.0: PCI bridge to [bus 09]
[ 0.214298] pci 0000:03:09.0: bridge window [mem 0xfc600000-0xfc6fffff]
[ 0.214307] pci 0000:03:0a.0: PCI bridge to [bus 0a]
[ 0.214311] pci 0000:03:0a.0: bridge window [mem 0xfc500000-0xfc5fffff]
[ 0.214319] pci 0000:02:00.0: PCI bridge to [bus 03-0a]
[ 0.214321] pci 0000:02:00.0: bridge window [io 0xd000-0xefff]
[ 0.214326] pci 0000:02:00.0: bridge window [mem 0xfc100000-0xfc7fffff]
[ 0.214329] pci 0000:02:00.0: bridge window [mem 0xe0000000-0xf01fffff 64bit pref]
[ 0.214335] pci 0000:00:01.2: PCI bridge to [bus 02-0a]
[ 0.214336] pci 0000:00:01.2: bridge window [io 0xd000-0xefff]
[ 0.214339] pci 0000:00:01.2: bridge window [mem 0xfc100000-0xfc7fffff]
[ 0.214341] pci 0000:00:01.2: bridge window [mem 0xe0000000-0xf01fffff 64bit pref]
[ 0.214344] pci 0000:0c:00.0: PCI bridge to [bus 0d]
[ 0.214345] pci 0000:0c:00.0: bridge window [io 0xf000-0xffff]
[ 0.214349] pci 0000:0c:00.0: bridge window [mem 0xfcb00000-0xfcbfffff]
[ 0.214351] pci 0000:0c:00.0: bridge window [mem 0xc0000000-0xd01fffff 64bit pref]
[ 0.214356] pci 0000:0b:00.0: PCI bridge to [bus 0c-0d]
[ 0.214357] pci 0000:0b:00.0: bridge window [io 0xf000-0xffff]
[ 0.214361] pci 0000:0b:00.0: bridge window [mem 0xfcb00000-0xfcbfffff]
[ 0.214363] pci 0000:0b:00.0: bridge window [mem 0xc0000000-0xd01fffff 64bit pref]
[ 0.214367] pci 0000:00:03.1: PCI bridge to [bus 0b-0d]
[ 0.214368] pci 0000:00:03.1: bridge window [io 0xf000-0xffff]
[ 0.214370] pci 0000:00:03.1: bridge window [mem 0xfcb00000-0xfccfffff]
[ 0.214372] pci 0000:00:03.1: bridge window [mem 0xc0000000-0xd01fffff 64bit pref]
[ 0.214375] pci 0000:00:07.1: PCI bridge to [bus 0e]
[ 0.214380] pci 0000:00:08.1: PCI bridge to [bus 0f]
[ 0.214383] pci 0000:00:08.1: bridge window [mem 0xfc800000-0xfcafffff]
[ 0.214387] pci 0000:00:08.2: PCI bridge to [bus 10]
[ 0.214389] pci 0000:00:08.2: bridge window [mem 0xfce00000-0xfcefffff]
[ 0.214393] pci 0000:00:08.3: PCI bridge to [bus 11]
[ 0.214395] pci 0000:00:08.3: bridge window [mem 0xfcd00000-0xfcdfffff]
[ 0.214400] pci_bus 0000:00: resource 4 [io 0x0000-0x03af window]
[ 0.214401] pci_bus 0000:00: resource 5 [io 0x03e0-0x0cf7 window]
[ 0.214401] pci_bus 0000:00: resource 6 [io 0x03b0-0x03df window]
[ 0.214402] pci_bus 0000:00: resource 7 [io 0x0d00-0xffff window]
[ 0.214402] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff window]
[ 0.214403] pci_bus 0000:00: resource 9 [mem 0x000c0000-0x000dffff window]
[ 0.214403] pci_bus 0000:00: resource 10 [mem 0xc0000000-0xfec02fff window]
[ 0.214404] pci_bus 0000:00: resource 11 [mem 0xfee00000-0xffffffff window]
[ 0.214405] pci_bus 0000:01: resource 1 [mem 0xfcf00000-0xfcffffff]
[ 0.214405] pci_bus 0000:02: resource 0 [io 0xd000-0xefff]
[ 0.214406] pci_bus 0000:02: resource 1 [mem 0xfc100000-0xfc7fffff]
[ 0.214406] pci_bus 0000:02: resource 2 [mem 0xe0000000-0xf01fffff 64bit pref]
[ 0.214407] pci_bus 0000:03: resource 0 [io 0xd000-0xefff]
[ 0.214407] pci_bus 0000:03: resource 1 [mem 0xfc100000-0xfc7fffff]
[ 0.214408] pci_bus 0000:03: resource 2 [mem 0xe0000000-0xf01fffff 64bit pref]
[ 0.214408] pci_bus 0000:04: resource 0 [io 0xe000-0xefff]
[ 0.214409] pci_bus 0000:04: resource 1 [mem 0xfc300000-0xfc4fffff]
[ 0.214410] pci_bus 0000:04: resource 2 [mem 0xe0000000-0xf01fffff 64bit pref]
[ 0.214410] pci_bus 0000:05: resource 0 [io 0xe000-0xefff]
[ 0.214411] pci_bus 0000:05: resource 1 [mem 0xfc300000-0xfc3fffff]
[ 0.214411] pci_bus 0000:05: resource 2 [mem 0xe0000000-0xf01fffff 64bit pref]
[ 0.214412] pci_bus 0000:06: resource 0 [io 0xe000-0xefff]
[ 0.214412] pci_bus 0000:06: resource 1 [mem 0xfc300000-0xfc3fffff]
[ 0.214413] pci_bus 0000:06: resource 2 [mem 0xe0000000-0xf01fffff 64bit pref]
[ 0.214413] pci_bus 0000:07: resource 0 [io 0xd000-0xdfff]
[ 0.214414] pci_bus 0000:07: resource 1 [mem 0xfc700000-0xfc7fffff]
[ 0.214415] pci_bus 0000:08: resource 1 [mem 0xfc100000-0xfc2fffff]
[ 0.214415] pci_bus 0000:09: resource 1 [mem 0xfc600000-0xfc6fffff]
[ 0.214416] pci_bus 0000:0a: resource 1 [mem 0xfc500000-0xfc5fffff]
[ 0.214417] pci_bus 0000:0b: resource 0 [io 0xf000-0xffff]
[ 0.214417] pci_bus 0000:0b: resource 1 [mem 0xfcb00000-0xfccfffff]
[ 0.214418] pci_bus 0000:0b: resource 2 [mem 0xc0000000-0xd01fffff 64bit pref]
[ 0.214418] pci_bus 0000:0c: resource 0 [io 0xf000-0xffff]
[ 0.214419] pci_bus 0000:0c: resource 1 [mem 0xfcb00000-0xfcbfffff]
[ 0.214419] pci_bus 0000:0c: resource 2 [mem 0xc0000000-0xd01fffff 64bit pref]
[ 0.214420] pci_bus 0000:0d: resource 0 [io 0xf000-0xffff]
[ 0.214420] pci_bus 0000:0d: resource 1 [mem 0xfcb00000-0xfcbfffff]
[ 0.214421] pci_bus 0000:0d: resource 2 [mem 0xc0000000-0xd01fffff 64bit pref]
[ 0.214422] pci_bus 0000:0f: resource 1 [mem 0xfc800000-0xfcafffff]
[ 0.214422] pci_bus 0000:10: resource 1 [mem 0xfce00000-0xfcefffff]
[ 0.214423] pci_bus 0000:11: resource 1 [mem 0xfcd00000-0xfcdfffff]
[ 0.214516] pci 0000:06:00.1: D0 power state depends on 0000:06:00.0
[ 0.214869] pci 0000:0d:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[ 0.214874] pci 0000:0d:00.1: D0 power state depends on 0000:0d:00.0
[ 0.214957] PCI: CLS 64 bytes, default 64
[ 0.214984] Trying to unpack rootfs image as initramfs...
[ 0.346593] Freeing initrd memory: 14840K
[ 0.346605] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.346606] software IO TLB: mapped [mem 0xb350a000-0xb750a000] (64MB)
[ 0.346643] amd_uncore: AMD NB counters detected
[ 0.346647] amd_uncore: AMD LLC counters detected
[ 0.346885] LVT offset 0 assigned for vector 0x400
[ 0.346979] perf: AMD IBS detected (0x000003ff)
[ 0.347015] check: Scanning for low memory corruption every 60 seconds
[ 0.347371] Initialise system trusted keyrings
[ 0.347381] Key type blacklist registered
[ 0.347424] workingset: timestamp_bits=41 max_order=24 bucket_order=0
[ 0.348043] zbud: loaded
[ 0.350463] Key type asymmetric registered
[ 0.350464] Asymmetric key parser 'x509' registered
[ 0.350467] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[ 0.350498] io scheduler mq-deadline registered
[ 0.350499] io scheduler kyber registered
[ 0.350513] io scheduler bfq registered
[ 0.350700] pcieport 0000:00:01.1: PME: Signaling with IRQ 26
[ 0.350780] pcieport 0000:00:01.2: PME: Signaling with IRQ 27
[ 0.350856] pcieport 0000:00:03.1: PME: Signaling with IRQ 28
[ 0.350977] pcieport 0000:00:07.1: PME: Signaling with IRQ 30
[ 0.351022] pcieport 0000:00:07.1: AER: enabled with IRQ 30
[ 0.351092] pcieport 0000:00:08.1: PME: Signaling with IRQ 31
[ 0.351127] pcieport 0000:00:08.1: AER: enabled with IRQ 31
[ 0.351228] pcieport 0000:00:08.2: PME: Signaling with IRQ 32
[ 0.351269] pcieport 0000:00:08.2: AER: enabled with IRQ 32
[ 0.351367] pcieport 0000:00:08.3: PME: Signaling with IRQ 33
[ 0.351409] pcieport 0000:00:08.3: AER: enabled with IRQ 33
[ 0.352883] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 0.352921] efifb: probing for efifb
[ 0.352942] efifb: framebuffer at 0xc0000000, using 3072k, total 3072k
[ 0.352942] efifb: mode is 1024x768x32, linelength=4096, pages=1
[ 0.352943] efifb: scrolling: redraw
[ 0.352943] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 0.352964] fbcon: Deferring console take-over
[ 0.352965] fb0: EFI VGA frame buffer device
[ 0.353011] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.353024] ACPI: Power Button [PWRB]
[ 0.353052] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.353765] ACPI: Power Button [PWRF]
[ 0.353829] Monitor-Mwait will be used to enter C-1 state
[ 0.353831] ACPI: \_PR_.C000: Found 2 idle states
[ 0.353931] ACPI: \_PR_.C002: Found 2 idle states
[ 0.353982] ACPI: \_PR_.C004: Found 2 idle states
[ 0.354055] ACPI: \_PR_.C006: Found 2 idle states
[ 0.354110] ACPI: \_PR_.C008: Found 2 idle states
[ 0.354199] ACPI: \_PR_.C00A: Found 2 idle states
[ 0.354281] ACPI: \_PR_.C00C: Found 2 idle states
[ 0.354344] ACPI: \_PR_.C00E: Found 2 idle states
[ 0.354400] ACPI: \_PR_.C001: Found 2 idle states
[ 0.354501] ACPI: \_PR_.C003: Found 2 idle states
[ 0.354597] ACPI: \_PR_.C005: Found 2 idle states
[ 0.354672] ACPI: \_PR_.C007: Found 2 idle states
[ 0.354730] ACPI: \_PR_.C009: Found 2 idle states
[ 0.354786] ACPI: \_PR_.C00B: Found 2 idle states
[ 0.354893] ACPI: \_PR_.C00D: Found 2 idle states
[ 0.354971] ACPI: \_PR_.C00F: Found 2 idle states
[ 1.360449] tsc: Refined TSC clocksource calibration: 3892.687 MHz
[ 1.360460] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x7038bbeea28, max_idle_ns: 881590619588 ns
[ 1.360498] clocksource: Switched to clocksource tsc
[ 2.375104] ACPI: Invalid passive threshold
[ 2.375313] thermal LNXTHERM:00: registered as thermal_zone0
[ 2.375314] ACPI: Thermal Zone [TZ10] (17 C)
[ 2.375369] ACPI: Invalid passive threshold
[ 2.375408] thermal LNXTHERM:01: registered as thermal_zone1
[ 2.375408] ACPI: Thermal Zone [PCT0] (17 C)
[ 2.375569] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 2.375863] AMD-Vi: AMD IOMMUv2 driver by Joerg Roedel <jroedel@suse.de>
[ 2.375864] AMD-Vi: AMD IOMMUv2 functionality not available on this system
[ 2.377270] nvme nvme0: pci function 0000:01:00.0
[ 2.377311] ahci 0000:09:00.0: version 3.0
[ 2.377524] ahci 0000:09:00.0: AHCI 0001.0301 32 slots 2 ports 6 Gbps 0xc impl SATA mode
[ 2.377525] ahci 0000:09:00.0: flags: 64bit ncq sntf ilck pm led clo only pmp fbs pio slum part sxs
[ 2.377748] scsi host0: ahci
[ 2.377829] scsi host1: ahci
[ 2.377882] scsi host2: ahci
[ 2.377946] scsi host3: ahci
[ 2.377973] ata1: DUMMY
[ 2.377973] ata2: DUMMY
[ 2.377975] ata3: SATA max UDMA/133 abar m2048@0xfc600000 port 0xfc600200 irq 48
[ 2.377977] ata4: SATA max UDMA/133 abar m2048@0xfc600000 port 0xfc600280 irq 48
[ 2.378149] ahci 0000:0a:00.0: AHCI 0001.0301 32 slots 4 ports 6 Gbps 0x33 impl SATA mode
[ 2.378150] ahci 0000:0a:00.0: flags: 64bit ncq sntf ilck pm led clo only pmp fbs pio slum part sxs
[ 2.378458] scsi host4: ahci
[ 2.378514] scsi host5: ahci
[ 2.378561] scsi host6: ahci
[ 2.378603] scsi host7: ahci
[ 2.378646] scsi host8: ahci
[ 2.378691] scsi host9: ahci
[ 2.378710] ata5: SATA max UDMA/133 abar m2048@0xfc500000 port 0xfc500100 irq 49
[ 2.378712] ata6: SATA max UDMA/133 abar m2048@0xfc500000 port 0xfc500180 irq 49
[ 2.378713] ata7: DUMMY
[ 2.378713] ata8: DUMMY
[ 2.378715] ata9: SATA max UDMA/133 abar m2048@0xfc500000 port 0xfc500300 irq 49
[ 2.378717] ata10: SATA max UDMA/133 abar m2048@0xfc500000 port 0xfc500380 irq 49
[ 2.378808] ahci 0000:10:00.0: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
[ 2.378810] ahci 0000:10:00.0: flags: 64bit ncq sntf ilck pm led clo only pmp fbs pio slum part
[ 2.378887] scsi host10: ahci
[ 2.378907] ata11: SATA max UDMA/133 abar m2048@0xfce00000 port 0xfce00100 irq 51
[ 2.378982] ahci 0000:11:00.0: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
[ 2.378983] ahci 0000:11:00.0: flags: 64bit ncq sntf ilck pm led clo only pmp fbs pio slum part
[ 2.379058] scsi host11: ahci
[ 2.379077] ata12: SATA max UDMA/133 abar m2048@0xfcd00000 port 0xfcd00100 irq 53
[ 2.379100] usbcore: registered new interface driver usbserial_generic
[ 2.379102] usbserial: USB Serial support registered for generic
[ 2.379119] rtc_cmos 00:03: RTC can wake from S4
[ 2.379277] rtc_cmos 00:03: registered as rtc0
[ 2.379309] rtc_cmos 00:03: setting system clock to 2020-10-08T08:16:35 UTC (1602144995)
[ 2.379318] rtc_cmos 00:03: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 2.379428] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.379510] drop_monitor: Initializing network drop monitor service
[ 2.379603] NET: Registered protocol family 10
[ 2.381992] Segment Routing with IPv6
[ 2.381992] RPL Segment Routing with IPv6
[ 2.382003] NET: Registered protocol family 17
[ 2.382823] microcode: CPU0: patch_level=0x08701013
[ 2.382827] microcode: CPU1: patch_level=0x08701013
[ 2.382830] microcode: CPU2: patch_level=0x08701013
[ 2.382845] microcode: CPU3: patch_level=0x08701013
[ 2.382859] microcode: CPU4: patch_level=0x08701013
[ 2.382872] microcode: CPU5: patch_level=0x08701013
[ 2.382887] microcode: CPU6: patch_level=0x08701013
[ 2.382889] microcode: CPU7: patch_level=0x08701013
[ 2.382895] microcode: CPU8: patch_level=0x08701013
[ 2.382899] microcode: CPU9: patch_level=0x08701013
[ 2.382904] microcode: CPU10: patch_level=0x08701013
[ 2.382910] microcode: CPU11: patch_level=0x08701013
[ 2.382915] microcode: CPU12: patch_level=0x08701013
[ 2.382919] microcode: CPU13: patch_level=0x08701013
[ 2.382923] microcode: CPU14: patch_level=0x08701013
[ 2.382928] microcode: CPU15: patch_level=0x08701013
[ 2.382948] microcode: Microcode Update Driver: v2.2.
[ 2.383095] resctrl: L3 allocation detected
[ 2.383096] resctrl: L3DATA allocation detected
[ 2.383096] resctrl: L3CODE allocation detected
[ 2.383096] resctrl: MB allocation detected
[ 2.383096] resctrl: L3 monitoring detected
[ 2.383098] IPI shorthand broadcast: enabled
[ 2.383103] sched_clock: Marking stable (2406419941, -23330397)->(2385911490, -2821946)
[ 2.383185] registered taskstats version 1
[ 2.383194] Loading compiled-in X.509 certificates
[ 2.383768] nvme nvme0: missing or invalid SUBNQN field.
[ 2.383780] nvme nvme0: Shutdown timeout set to 8 seconds
[ 2.384571] Loaded X.509 cert 'Build time autogenerated kernel key: 65ffbe7aae84dcdfecfb2c43cc155c8e5e23c456'
[ 2.384685] zswap: loaded using pool lz4/z3fold
[ 2.384823] Key type ._fscrypt registered
[ 2.384823] Key type .fscrypt registered
[ 2.384824] Key type fscrypt-provisioning registered
[ 2.385121] PM: Magic number: 8:192:270
[ 2.385253] RAS: Correctable Errors collector initialized.
[ 2.410989] nvme nvme0: 32/0/0 default/read/poll queues
[ 2.414342] nvme0n1: p1 p2
[ 2.687167] ata5: SATA link down (SStatus 0 SControl 300)
[ 2.687191] ata11: SATA link down (SStatus 0 SControl 300)
[ 2.687569] ata6: SATA link down (SStatus 0 SControl 300)
[ 2.687608] ata9: SATA link down (SStatus 0 SControl 300)
[ 2.687759] ata10: SATA link down (SStatus 0 SControl 300)
[ 2.687837] ata4: SATA link down (SStatus 0 SControl 300)
[ 2.687874] ata3: SATA link down (SStatus 0 SControl 300)
[ 2.690282] ata12: SATA link down (SStatus 0 SControl 300)
[ 2.691149] Freeing unused decrypted memory: 2040K
[ 2.691346] Freeing unused kernel image (initmem) memory: 1644K
[ 2.691348] Write protecting the kernel read-only data: 24576k
[ 2.691728] Freeing unused kernel image (text/rodata gap) memory: 2044K
[ 2.691827] Freeing unused kernel image (rodata/data gap) memory: 276K
[ 2.713240] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[ 2.713244] Run /init as init process
[ 2.713244] with arguments:
[ 2.713245] /init
[ 2.713245] with environment:
[ 2.713245] HOME=/
[ 2.713246] TERM=linux
[ 2.713246] BOOT_IMAGE=/root/boot/vmlinuz-linux
[ 2.740504] systemd[1]: systemd 246.6-1-arch running in system mode. (+PAM +AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid)
[ 2.756701] systemd[1]: Detected architecture x86-64.
[ 2.756702] systemd[1]: Running in initial RAM disk.
[ 2.787228] fbcon: Taking over console
[ 2.787260] systemd[1]: Initializing machine ID from random generator.
[ 2.794548] Console: switching to colour frame buffer device 128x48
[ 2.804136] systemd[1]: Queued start job for default target Initrd Default Target.
[ 2.804586] systemd[1]: Created slice system-systemd\x2dcryptsetup.slice.
[ 2.804671] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 2.804722] systemd[1]: Reached target Local File Systems.
[ 2.804755] systemd[1]: Reached target Paths.
[ 2.804785] systemd[1]: Reached target Slices.
[ 2.804815] systemd[1]: Reached target Swap.
[ 2.804848] systemd[1]: Reached target Timers.
[ 2.804925] systemd[1]: Listening on Journal Audit Socket.
[ 2.804989] systemd[1]: Listening on Journal Socket (/dev/log).
[ 2.805051] systemd[1]: Listening on Journal Socket.
[ 2.805113] systemd[1]: Listening on udev Control Socket.
[ 2.805166] systemd[1]: Listening on udev Kernel Socket.
[ 2.805204] systemd[1]: Reached target Sockets.
[ 2.805593] systemd[1]: Starting Create list of static device nodes for the current kernel...
[ 2.806463] systemd[1]: Starting Journal Service...
[ 2.806932] systemd[1]: Starting Load Kernel Modules...
[ 2.807391] systemd[1]: Starting Coldplug All udev Devices...
[ 2.807749] systemd[1]: Finished Create list of static device nodes for the current kernel.
[ 2.808260] systemd[1]: Starting Create Static Device Nodes in /dev...
[ 2.810732] systemd[1]: Finished Create Static Device Nodes in /dev.
[ 2.811402] systemd[1]: Starting Rule-based Manager for Device Events and Files...
[ 2.828141] systemd[1]: Started Rule-based Manager for Device Events and Files.
[ 2.841136] systemd[1]: Started Journal Service.
[ 2.861816] xhci_hcd 0000:08:00.1: xHCI Host Controller
[ 2.861821] xhci_hcd 0000:08:00.1: new USB bus registered, assigned bus number 1
[ 2.861982] xhci_hcd 0000:08:00.1: hcc params 0x0278ffe5 hci version 0x110 quirks 0x0000000000000410
[ 2.862620] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08
[ 2.862621] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.862622] usb usb1: Product: xHCI Host Controller
[ 2.862623] usb usb1: Manufacturer: Linux 5.8.13-arch1-1 xhci-hcd
[ 2.862623] usb usb1: SerialNumber: 0000:08:00.1
[ 2.862797] hub 1-0:1.0: USB hub found
[ 2.862812] hub 1-0:1.0: 6 ports detected
[ 2.863076] xhci_hcd 0000:08:00.1: xHCI Host Controller
[ 2.863079] xhci_hcd 0000:08:00.1: new USB bus registered, assigned bus number 2
[ 2.863082] xhci_hcd 0000:08:00.1: Host supports USB 3.1 Enhanced SuperSpeed
[ 2.863108] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.863128] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.08
[ 2.863129] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.863130] usb usb2: Product: xHCI Host Controller
[ 2.863131] usb usb2: Manufacturer: Linux 5.8.13-arch1-1 xhci-hcd
[ 2.863132] usb usb2: SerialNumber: 0000:08:00.1
[ 2.863209] hub 2-0:1.0: USB hub found
[ 2.863218] hub 2-0:1.0: 4 ports detected
[ 2.863425] ccp 0000:0f:00.1: enabling device (0000 -> 0002)
[ 2.863493] xhci_hcd 0000:08:00.3: xHCI Host Controller
[ 2.863496] xhci_hcd 0000:08:00.3: new USB bus registered, assigned bus number 3
[ 2.863560] ccp 0000:0f:00.1: ccp: unable to access the device: you might be running a broken BIOS.
[ 2.863666] xhci_hcd 0000:08:00.3: hcc params 0x0278ffe5 hci version 0x110 quirks 0x0000000000000410
[ 2.863948] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08
[ 2.863950] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.863951] usb usb3: Product: xHCI Host Controller
[ 2.863951] usb usb3: Manufacturer: Linux 5.8.13-arch1-1 xhci-hcd
[ 2.863953] usb usb3: SerialNumber: 0000:08:00.3
[ 2.864034] hub 3-0:1.0: USB hub found
[ 2.864047] hub 3-0:1.0: 6 ports detected
[ 2.864326] xhci_hcd 0000:08:00.3: xHCI Host Controller
[ 2.864328] xhci_hcd 0000:08:00.3: new USB bus registered, assigned bus number 4
[ 2.864335] xhci_hcd 0000:08:00.3: Host supports USB 3.1 Enhanced SuperSpeed
[ 2.864348] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.864363] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.08
[ 2.864364] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.864364] usb usb4: Product: xHCI Host Controller
[ 2.864365] usb usb4: Manufacturer: Linux 5.8.13-arch1-1 xhci-hcd
[ 2.864366] usb usb4: SerialNumber: 0000:08:00.3
[ 2.864442] hub 4-0:1.0: USB hub found
[ 2.864452] hub 4-0:1.0: 4 ports detected
[ 2.864495] usb: port power management may be unreliable
[ 2.864680] xhci_hcd 0000:0f:00.3: xHCI Host Controller
[ 2.864684] xhci_hcd 0000:0f:00.3: new USB bus registered, assigned bus number 5
[ 2.864788] xhci_hcd 0000:0f:00.3: hcc params 0x0278ffe5 hci version 0x110 quirks 0x0000000000000410
[ 2.865000] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08
[ 2.865001] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.865002] usb usb5: Product: xHCI Host Controller
[ 2.865004] usb usb5: Manufacturer: Linux 5.8.13-arch1-1 xhci-hcd
[ 2.865005] usb usb5: SerialNumber: 0000:0f:00.3
[ 2.865072] hub 5-0:1.0: USB hub found
[ 2.865078] hub 5-0:1.0: 4 ports detected
[ 2.865234] xhci_hcd 0000:0f:00.3: xHCI Host Controller
[ 2.865236] xhci_hcd 0000:0f:00.3: new USB bus registered, assigned bus number 6
[ 2.865237] xhci_hcd 0000:0f:00.3: Host supports USB 3.1 Enhanced SuperSpeed
[ 2.865247] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.865260] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.08
[ 2.865262] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.865263] usb usb6: Product: xHCI Host Controller
[ 2.865263] usb usb6: Manufacturer: Linux 5.8.13-arch1-1 xhci-hcd
[ 2.865264] usb usb6: SerialNumber: 0000:0f:00.3
[ 2.865318] hub 6-0:1.0: USB hub found
[ 2.865325] hub 6-0:1.0: 4 ports detected
[ 2.866504] cryptd: max_cpu_qlen set to 1000
[ 2.866686] raid6: avx2x4 gen() 32216 MB/s
[ 2.869705] AVX2 version of gcm_enc/dec engaged.
[ 2.869706] AES CTR mode by8 optimization enabled
[ 2.873385] device-mapper: uevent: version 1.0.3
[ 2.873778] device-mapper: ioctl: 4.42.0-ioctl (2020-02-27) initialised: dm-devel@redhat.com
[ 2.923340] raid6: avx2x4 xor() 10070 MB/s
[ 2.980009] raid6: avx2x2 gen() 34982 MB/s
[ 3.036680] raid6: avx2x2 xor() 25009 MB/s
[ 3.093360] raid6: avx2x1 gen() 29099 MB/s
[ 3.150011] raid6: avx2x1 xor() 19449 MB/s
[ 3.190027] usb 1-1: new high-speed USB device number 2 using xhci_hcd
[ 3.206689] raid6: sse2x4 gen() 18129 MB/s
[ 3.263357] raid6: sse2x4 xor() 9252 MB/s
[ 3.320004] raid6: sse2x2 gen() 18005 MB/s
[ 3.331746] usb 1-1: New USB device found, idVendor=1a40, idProduct=0101, bcdDevice= 1.00
[ 3.331748] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 3.331749] usb 1-1: Product: USB 2.0 Hub [MTT]
[ 3.375270] hub 1-1:1.0: USB hub found
[ 3.375618] hub 1-1:1.0: 4 ports detected
[ 3.376672] raid6: sse2x2 xor() 13073 MB/s
[ 3.433338] raid6: sse2x1 gen() 15397 MB/s
[ 3.490013] raid6: sse2x1 xor() 10265 MB/s
[ 3.490014] raid6: using algorithm avx2x2 gen() 34982 MB/s
[ 3.490015] raid6: .... xor() 25009 MB/s, rmw enabled
[ 3.490015] raid6: using avx2x2 recovery algorithm
[ 3.490681] xor: automatically using best checksumming function avx
[ 3.512274] Btrfs loaded, crc32c=crc32c-intel
[ 3.514093] hid: raw HID events driver (C) Jiri Kosina
[ 3.515192] usbcore: registered new interface driver usbhid
[ 3.515193] usbhid: USB HID core driver
[ 3.516521] usbcore: registered new interface driver usb-storage
[ 3.517913] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.563359] usb 1-2: new high-speed USB device number 3 using xhci_hcd
[ 3.705376] usb 1-2: New USB device found, idVendor=1a40, idProduct=0101, bcdDevice= 1.00
[ 3.705377] usb 1-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 3.705378] usb 1-2: Product: USB 2.0 Hub [MTT]
[ 3.759524] hub 1-2:1.0: USB hub found
[ 3.759860] hub 1-2:1.0: 4 ports detected
[ 3.876680] usb 1-1.4: new high-speed USB device number 4 using xhci_hcd
[ 4.069484] usb 1-1.4: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=85.36
[ 4.069486] usb 1-1.4: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 4.069487] usb 1-1.4: Product: USB2.0 Hub
[ 4.111501] hub 1-1.4:1.0: USB hub found
[ 4.112106] hub 1-1.4:1.0: 4 ports detected
[ 4.240010] usb 1-2.4: new high-speed USB device number 5 using xhci_hcd
[ 4.432480] usb 1-2.4: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=85.36
[ 4.432481] usb 1-2.4: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 4.432482] usb 1-2.4: Product: USB2.0 Hub
[ 4.495496] hub 1-2.4:1.0: USB hub found
[ 4.496101] hub 1-2.4:1.0: 4 ports detected
[ 4.503358] usb 1-1.4.2: new full-speed USB device number 6 using xhci_hcd
[ 4.608114] usb 1-1.4.2: New USB device found, idVendor=08bb, idProduct=2704, bcdDevice= 1.00
[ 4.608115] usb 1-1.4.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 4.608116] usb 1-1.4.2: Product: USB Audio DAC
[ 4.608117] usb 1-1.4.2: Manufacturer: Burr-Brown from TI
[ 4.662763] input: Burr-Brown from TI USB Audio DAC as /devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:03:08.0/0000:08:00.1/usb1/1-1/1-1.4/1-1.4.2/1-1.4.2:1.2/0003:08BB:2704.0001/input/input2
[ 4.677972] random: fast init done
[ 4.716846] hid-generic 0003:08BB:2704.0001: input,hidraw0: USB HID v1.00 Device [Burr-Brown from TI USB Audio DAC ] on usb-0000:08:00.1-1.4.2/input2
[ 4.733358] usb 1-1.4.4: new high-speed USB device number 7 using xhci_hcd
[ 4.825709] usb 1-1.4.4: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=85.36
[ 4.825710] usb 1-1.4.4: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 4.825710] usb 1-1.4.4: Product: USB2.0 Hub
[ 4.879495] hub 1-1.4.4:1.0: USB hub found
[ 4.880114] hub 1-1.4.4:1.0: 4 ports detected
[ 4.896692] usb 1-2.4.1: new high-speed USB device number 8 using xhci_hcd
[ 4.976732] Key type encrypted registered
[ 4.977809] random: systemd-cryptse: uninitialized urandom read (2 bytes read)
[ 4.986241] BTRFS: device label gfr_crypt devid 1 transid 298523 /dev/dm-0 scanned by systemd-udevd (283)
[ 4.992596] usb 1-2.4.1: New USB device found, idVendor=0451, idProduct=8142, bcdDevice= 1.00
[ 4.992597] usb 1-2.4.1: New USB device strings: Mfr=0, Product=0, SerialNumber=1
[ 4.992598] usb 1-2.4.1: SerialNumber: CC010871FE0F
[ 5.004053] BTRFS info (device dm-0): disk space caching is enabled
[ 5.004054] BTRFS info (device dm-0): has skinny extents
[ 5.024685] BTRFS info (device dm-0): enabling ssd optimizations
[ 5.039239] hub 1-2.4.1:1.0: USB hub found
[ 5.039584] hub 1-2.4.1:1.0: 4 ports detected
[ 5.173349] usb 1-1.4.4.2: new full-speed USB device number 9 using xhci_hcd
[ 5.232757] systemd[1]: systemd 246.6-1-arch running in system mode. (+PAM +AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid)
[ 5.250034] systemd[1]: Detected architecture x86-64.
[ 5.251395] systemd[1]: Set hostname to <gallifrey>.
[ 5.284121] usb 1-1.4.4.2: New USB device found, idVendor=046d, idProduct=c52b, bcdDevice=24.11
[ 5.284122] usb 1-1.4.4.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 5.284123] usb 1-1.4.4.2: Product: USB Receiver
[ 5.284124] usb 1-1.4.4.2: Manufacturer: Logitech
[ 5.310610] systemd[1]: initrd-switch-root.service: Current command vanished from the unit file, execution of the command list won't be resumed.
[ 5.323915] systemd[1]: initrd-switch-root.service: Succeeded.
[ 5.324075] systemd[1]: Stopped Switch Root.
[ 5.324534] systemd[1]: systemd-journald.service: Scheduled restart job, restart counter is at 1.
[ 5.324666] systemd[1]: Created slice system-getty.slice.
[ 5.325123] systemd[1]: Created slice system-modprobe.slice.
[ 5.325563] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ 5.325997] systemd[1]: Created slice User and Session Slice.
[ 5.326344] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 5.326693] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 5.327105] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 5.327461] systemd[1]: Reached target Local Encrypted Volumes.
[ 5.327810] systemd[1]: Reached target Login Prompts.
[ 5.328148] systemd[1]: Stopped target Switch Root.
[ 5.328486] systemd[1]: Stopped target Initrd File Systems.
[ 5.328816] systemd[1]: Stopped target Initrd Root File System.
[ 5.329155] systemd[1]: Reached target Paths.
[ 5.329484] systemd[1]: Reached target Remote File Systems.
[ 5.329807] systemd[1]: Reached target Slices.
[ 5.330189] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ 5.330796] systemd[1]: Listening on LVM2 metadata daemon socket.
[ 5.331320] systemd[1]: Listening on LVM2 poll daemon socket.
[ 5.332105] systemd[1]: Listening on Process Core Dump Socket.
[ 5.332560] systemd[1]: Listening on udev Control Socket.
[ 5.332908] systemd[1]: Listening on udev Kernel Socket.
[ 5.333628] systemd[1]: Mounting Huge Pages File System...
[ 5.334380] systemd[1]: Mounting POSIX Message Queue File System...
[ 5.335139] systemd[1]: Mounting Kernel Debug File System...
[ 5.335886] systemd[1]: Mounting Kernel Trace File System...
[ 5.336653] systemd[1]: Starting Create list of static device nodes for the current kernel...
[ 5.337401] systemd[1]: Starting Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling...
[ 5.338393] systemd[1]: Starting Load Kernel Module drm...
[ 5.340013] usb 1-2.4.3: new high-speed USB device number 10 using xhci_hcd
[ 5.340036] systemd[1]: Starting Set Up Additional Binary Formats...
[ 5.340475] systemd[1]: systemd-cryptsetup@gfr_crypt.service: Succeeded.
[ 5.340567] systemd[1]: Stopped systemd-cryptsetup@gfr_crypt.service.
[ 5.340993] systemd[1]: systemd-fsck-root.service: Succeeded.
[ 5.341161] systemd[1]: Stopped File System Check on Root Device.
[ 5.341574] systemd[1]: Stopped Journal Service.
[ 5.342114] Linux agpgart interface v0.103
[ 5.342712] systemd[1]: Starting Journal Service...
[ 5.342859] random: lvm: uninitialized urandom read (4 bytes read)
[ 5.343364] systemd[1]: Condition check resulted in Load Kernel Modules being skipped.
[ 5.343424] systemd[1]: Condition check resulted in FUSE Control File System being skipped.
[ 5.343970] systemd[1]: Mounting Kernel Configuration File System...
[ 5.344729] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 5.345106] systemd[1]: Condition check resulted in Repartition Root Disk being skipped.
[ 5.345455] systemd[1]: Starting Apply Kernel Variables...
[ 5.346253] systemd[1]: Starting Coldplug All udev Devices...
[ 5.347046] systemd[1]: sysroot.mount: Succeeded.
[ 5.347292] systemd[1]: Mounted Huge Pages File System.
[ 5.347697] systemd[1]: Mounted POSIX Message Queue File System.
[ 5.348086] systemd[1]: Mounted Kernel Debug File System.
[ 5.348480] systemd[1]: Mounted Kernel Trace File System.
[ 5.349030] systemd[1]: Finished Create list of static device nodes for the current kernel.
[ 5.349464] systemd[1]: Mounted Kernel Configuration File System.
[ 5.350007] systemd[1]: Finished Remount Root and Kernel File Systems.
[ 5.350596] systemd[1]: Finished Apply Kernel Variables.
[ 5.351007] systemd[1]: proc-sys-fs-binfmt_misc.automount: Got automount request for /proc/sys/fs/binfmt_misc, triggered by 432 (systemd-binfmt)
[ 5.351518] systemd[1]: Mounting Arbitrary Executable File Formats File System...
[ 5.351908] systemd[1]: Condition check resulted in First Boot Wizard being skipped.
[ 5.352970] systemd[1]: Starting Rebuild Hardware Database...
[ 5.353864] systemd[1]: Starting Load/Save Random Seed...
[ 5.354658] systemd[1]: Starting Create System Users...
[ 5.355465] systemd[1]: Mounted Arbitrary Executable File Formats File System.
[ 5.356631] systemd[1]: Finished Set Up Additional Binary Formats.
[ 5.361866] systemd[1]: modprobe@drm.service: Succeeded.
[ 5.362039] systemd[1]: Finished Load Kernel Module drm.
[ 5.367257] systemd[1]: Started Journal Service.
[ 5.400215] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:03:08.0/0000:08:00.1/usb1/1-1/1-1.4/1-1.4.4/1-1.4.4.2/1-1.4.4.2:1.0/0003:046D:C52B.0002/input/input3
[ 5.453078] usb 1-2.4.3: New USB device found, idVendor=041e, idProduct=3f04, bcdDevice= 1.00
[ 5.453080] usb 1-2.4.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 5.453081] usb 1-2.4.3: Product: E-MU 0404 | USB
[ 5.453081] usb 1-2.4.3: Manufacturer: E-MU Systems, Inc.
[ 5.453082] usb 1-2.4.3: SerialNumber: E-MU-BA-FFFF-07D6091E-0C5D1-STN 01
[ 5.456724] hid-generic 0003:046D:C52B.0002: input,hidraw1: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-0000:08:00.1-1.4.4.2/input0
[ 5.490276] input: Logitech USB Receiver Mouse as /devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:03:08.0/0000:08:00.1/usb1/1-1/1-1.4/1-1.4.4/1-1.4.4.2/1-1.4.4.2:1.1/0003:046D:C52B.0003/input/input4
[ 5.490298] input: Logitech USB Receiver Consumer Control as /devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:03:08.0/0000:08:00.1/usb1/1-1/1-1.4/1-1.4.4/1-1.4.4.2/1-1.4.4.2:1.1/0003:046D:C52B.0003/input/input5
[ 5.523345] usb 1-2.4.1.1: new low-speed USB device number 11 using xhci_hcd
[ 5.546694] input: Logitech USB Receiver System Control as /devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:03:08.0/0000:08:00.1/usb1/1-1/1-1.4/1-1.4.4/1-1.4.4.2/1-1.4.4.2:1.1/0003:046D:C52B.0003/input/input6
[ 5.546751] hid-generic 0003:046D:C52B.0003: input,hiddev0,hidraw2: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:08:00.1-1.4.4.2/input1
[ 5.550224] hid-generic 0003:046D:C52B.0004: hiddev1,hidraw3: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:08:00.1-1.4.4.2/input2
[ 5.629150] usb 1-2.4.1.1: New USB device found, idVendor=046d, idProduct=c016, bcdDevice= 3.40
[ 5.629152] usb 1-2.4.1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 5.629153] usb 1-2.4.1.1: Product: Optical USB Mouse
[ 5.629154] usb 1-2.4.1.1: Manufacturer: Logitech
[ 5.637064] acpi_cpufreq: overriding BIOS provided _PSD data
[ 5.654213] acpi PNP0C14:01: duplicate WMI GUID 05901221-D566-11D1-B2F0-00A0C9062910 (first instance was on PNP0C14:00)
[ 5.684282] input: Logitech Optical USB Mouse as /devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:03:08.0/0000:08:00.1/usb1/1-2/1-2.4/1-2.4.1/1-2.4.1.1/1-2.4.1.1:1.0/0003:046D:C016.0005/input/input8
[ 5.684372] hid-generic 0003:046D:C016.0005: input,hidraw4: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:08:00.1-2.4.1.1/input0
[ 5.686685] usb 1-2.4.4: new high-speed USB device number 12 using xhci_hcd
[ 5.714578] input: PC Speaker as /devices/platform/pcspkr/input/input9
[ 5.714617] ACPI Warning: SystemIO range 0x0000000000000B00-0x0000000000000B08 conflicts with OpRegion 0x0000000000000B00-0x0000000000000B0F (\GSA1.SMBI) (20200528/utaddress-204)
[ 5.714630] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 5.714942] RAPL PMU: API unit is 2^-32 Joules, 1 fixed counters, 163840 ms ovfl timer
[ 5.714943] RAPL PMU: hw unit of domain package 2^-16 Joules
[ 5.717524] sp5100_tco: SP5100/SB800 TCO WatchDog Timer Driver
[ 5.717575] sp5100-tco sp5100-tco: Using 0xfed80b00 for watchdog MMIO address
[ 5.717580] sp5100-tco sp5100-tco: Watchdog hardware is disabled
[ 5.753120] libphy: r8169: probed
[ 5.753282] r8169 0000:07:00.0 eth0: RTL8168h/8111h, b4:2e:99:a5:ad:1a, XID 541, IRQ 107
[ 5.753284] r8169 0000:07:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko]
[ 5.779206] usb 1-2.4.4: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=85.36
[ 5.779210] usb 1-2.4.4: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 5.779212] usb 1-2.4.4: Product: USB2.0 Hub
[ 5.792986] BTRFS info (device dm-0): device fsid 76f7fd1a-6b0a-4bdd-93c6-a34f63b5d697 devid 1 moved old:/dev/mapper/gfr_crypt new:/dev/dm-0
[ 5.793233] BTRFS info (device dm-0): device fsid 76f7fd1a-6b0a-4bdd-93c6-a34f63b5d697 devid 1 moved old:/dev/dm-0 new:/dev/mapper/gfr_crypt
[ 5.810107] mc: Linux media interface: v0.10
[ 5.817876] kvm: Nested Virtualization enabled
[ 5.817894] SVM: kvm: Nested Paging enabled
[ 5.817895] SVM: Virtual VMLOAD VMSAVE supported
[ 5.817895] SVM: Virtual GIF supported
[ 5.820347] MCE: In-kernel MCE decoding enabled.
[ 5.823395] EDAC amd64: F17h_M70h detected (node 0).
[ 5.823441] EDAC amd64: Node 0: DRAM ECC disabled.
[ 5.839495] hub 1-2.4.4:1.0: USB hub found
[ 5.840077] hub 1-2.4.4:1.0: 4 ports detected
[ 5.850015] usb 1-2.4.1.4: new high-speed USB device number 13 using xhci_hcd
[ 5.850400] Adding 16777212k swap on /swap/file. Priority:-2 extents:19 across:29200436k FS
[ 5.907480] EDAC amd64: F17h_M70h detected (node 0).
[ 5.907539] EDAC amd64: Node 0: DRAM ECC disabled.
[ 5.910900] snd_hda_intel 0000:06:00.1: Force to non-snoop mode
[ 5.911214] snd_hda_intel 0000:0d:00.1: Force to non-snoop mode
[ 5.911399] snd_hda_intel 0000:0f:00.4: enabling device (0000 -> 0002)
[ 5.922341] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:03:02.0/0000:04:00.0/0000:05:00.0/0000:06:00.1/sound/card1/input16
[ 5.922404] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.1/0000:0b:00.0/0000:0c:00.0/0000:0d:00.1/sound/card2/input10
[ 5.952452] usb 1-2.4.1.4: New USB device found, idVendor=0451, idProduct=8142, bcdDevice= 1.00
[ 5.952455] usb 1-2.4.1.4: New USB device strings: Mfr=0, Product=0, SerialNumber=1
[ 5.952457] usb 1-2.4.1.4: SerialNumber: AC010081FE0F
[ 6.003537] input: HDA ATI HDMI HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:03:02.0/0000:04:00.0/0000:05:00.0/0000:06:00.1/sound/card1/input17
[ 6.003594] input: HDA ATI HDMI HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:03:02.0/0000:04:00.0/0000:05:00.0/0000:06:00.1/sound/card1/input18
[ 6.003643] input: HDA ATI HDMI HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:03.1/0000:0b:00.0/0000:0c:00.0/0000:0d:00.1/sound/card2/input11
[ 6.003678] input: HDA ATI HDMI HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:03.1/0000:0b:00.0/0000:0c:00.0/0000:0d:00.1/sound/card2/input12
[ 6.003715] input: HDA ATI HDMI HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:03:02.0/0000:04:00.0/0000:05:00.0/0000:06:00.1/sound/card1/input19
[ 6.003761] input: HDA ATI HDMI HDMI/DP,pcm=10 as /devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:03:02.0/0000:04:00.0/0000:05:00.0/0000:06:00.1/sound/card1/input20
[ 6.003808] input: HDA ATI HDMI HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:03.1/0000:0b:00.0/0000:0c:00.0/0000:0d:00.1/sound/card2/input13
[ 6.003847] input: HDA ATI HDMI HDMI/DP,pcm=10 as /devices/pci0000:00/0000:00:03.1/0000:0b:00.0/0000:0c:00.0/0000:0d:00.1/sound/card2/input14
[ 6.003884] input: HDA ATI HDMI HDMI/DP,pcm=11 as /devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:03:02.0/0000:04:00.0/0000:05:00.0/0000:06:00.1/sound/card1/input21
[ 6.003946] logitech-djreceiver 0003:046D:C52B.0004: hiddev0,hidraw1: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:08:00.1-1.4.4.2/input2
[ 6.004116] input: HDA ATI HDMI HDMI/DP,pcm=11 as /devices/pci0000:00/0000:00:03.1/0000:0b:00.0/0000:0c:00.0/0000:0d:00.1/sound/card2/input15
[ 6.026999] EDAC amd64: F17h_M70h detected (node 0).
[ 6.027054] EDAC amd64: Node 0: DRAM ECC disabled.
[ 6.031240] hub 1-2.4.1.4:1.0: USB hub found
[ 6.031447] hub 1-2.4.1.4:1.0: 4 ports detected
[ 6.055370] snd_hda_codec_realtek hdaudioC3D0: autoconfig for ALC887-VD: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line
[ 6.055373] snd_hda_codec_realtek hdaudioC3D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 6.055375] snd_hda_codec_realtek hdaudioC3D0: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[ 6.055376] snd_hda_codec_realtek hdaudioC3D0: mono: mono_out=0x0
[ 6.055378] snd_hda_codec_realtek hdaudioC3D0: inputs:
[ 6.055380] snd_hda_codec_realtek hdaudioC3D0: Front Mic=0x19
[ 6.055381] snd_hda_codec_realtek hdaudioC3D0: Rear Mic=0x18
[ 6.055383] snd_hda_codec_realtek hdaudioC3D0: Line=0x1a
[ 6.084735] [drm] amdgpu kernel modesetting enabled.
[ 6.084788] amdgpu: Ignoring ACPI CRAT on non-APU system
[ 6.084790] Virtual CRAT table created for CPU
[ 6.084800] amdgpu: Topology: Add CPU node
[ 6.084881] checking generic (c0000000 300000) vs hw (e0000000 10000000)
[ 6.084881] checking generic (c0000000 300000) vs hw (f0000000 200000)
[ 6.084882] checking generic (c0000000 300000) vs hw (fc300000 80000)
[ 6.084913] amdgpu 0000:06:00.0: enabling device (0000 -> 0003)
[ 6.084976] [drm] initializing kernel modesetting (NAVI10 0x1002:0x731F 0x1DA2:0xE410 0xC1).
[ 6.084978] amdgpu 0000:06:00.0: amdgpu: Trusted Memory Zone (TMZ) feature disabled as experimental (default)
[ 6.084985] [drm] register mmio base: 0xFC300000
[ 6.084985] [drm] register mmio size: 524288
[ 6.085003] [drm] PCIE atomic ops is not supported
[ 6.085113] input: HD-Audio Generic Front Mic as /devices/pci0000:00/0000:00:08.1/0000:0f:00.4/sound/card3/input22
[ 6.085163] input: HD-Audio Generic Rear Mic as /devices/pci0000:00/0000:00:08.1/0000:0f:00.4/sound/card3/input23
[ 6.085207] input: HD-Audio Generic Line as /devices/pci0000:00/0000:00:08.1/0000:0f:00.4/sound/card3/input24
[ 6.085250] input: HD-Audio Generic Line Out as /devices/pci0000:00/0000:00:08.1/0000:0f:00.4/sound/card3/input25
[ 6.085297] input: HD-Audio Generic Front Headphone as /devices/pci0000:00/0000:00:08.1/0000:0f:00.4/sound/card3/input26
[ 6.116344] [drm] add ip block number 0 <nv_common>
[ 6.116344] [drm] add ip block number 1 <gmc_v10_0>
[ 6.116345] [drm] add ip block number 2 <navi10_ih>
[ 6.116346] [drm] add ip block number 3 <psp>
[ 6.116347] [drm] add ip block number 4 <smu>
[ 6.116347] [drm] add ip block number 5 <dm>
[ 6.116348] [drm] add ip block number 6 <gfx_v10_0>
[ 6.116349] [drm] add ip block number 7 <sdma_v5_0>
[ 6.116349] [drm] add ip block number 8 <vcn_v2_0>
[ 6.116349] [drm] add ip block number 9 <jpeg_v2_0>
[ 6.123674] input: Logitech Wireless Device PID:404d Keyboard as /devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:03:08.0/0000:08:00.1/usb1/1-1/1-1.4/1-1.4.4/1-1.4.4.2/1-1.4.4.2:1.2/0003:046D:C52B.0004/0003:046D:404D.0006/input/input27
[ 6.123735] input: Logitech Wireless Device PID:404d Mouse as /devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:03:08.0/0000:08:00.1/usb1/1-1/1-1.4/1-1.4.4/1-1.4.4.2/1-1.4.4.2:1.2/0003:046D:C52B.0004/0003:046D:404D.0006/input/input28
[ 6.123799] input: Logitech Wireless Device PID:404d Consumer Control as /devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:03:08.0/0000:08:00.1/usb1/1-1/1-1.4/1-1.4.4/1-1.4.4.2/1-1.4.4.2:1.2/0003:046D:C52B.0004/0003:046D:404D.0006/input/input29
[ 6.123850] input: Logitech Wireless Device PID:404d System Control as /devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:03:08.0/0000:08:00.1/usb1/1-1/1-1.4/1-1.4.4/1-1.4.4.2/1-1.4.4.2:1.2/0003:046D:C52B.0004/0003:046D:404D.0006/input/input30
[ 6.123915] hid-generic 0003:046D:404D.0006: input,hidraw2: USB HID v1.11 Keyboard [Logitech Wireless Device PID:404d] on usb-0000:08:00.1-1.4.4.2/input2:1
[ 6.136683] usb 1-2.4.4.1: new high-speed USB device number 14 using xhci_hcd
[ 6.152162] EDAC amd64: F17h_M70h detected (node 0).
[ 6.152209] EDAC amd64: Node 0: DRAM ECC disabled.
[ 6.239078] usb 1-2.4.4.1: New USB device found, idVendor=0451, idProduct=8142, bcdDevice= 1.00
[ 6.239081] usb 1-2.4.4.1: New USB device strings: Mfr=0, Product=0, SerialNumber=1
[ 6.239082] usb 1-2.4.4.1: SerialNumber: 870008796538
[ 6.239868] amdgpu: ATOM BIOS: 113-410XT-UO4
[ 6.239876] [drm] VCN decode is enabled in VM mode
[ 6.239877] [drm] VCN encode is enabled in VM mode
[ 6.239877] [drm] JPEG decode is enabled in VM mode
[ 6.239885] [drm] GPU posting now...
[ 6.239924] [drm] vm size is 262144 GB, 4 levels, block size is 9-bit, fragment size is 9-bit
[ 6.239931] amdgpu 0000:06:00.0: amdgpu: VRAM: 8176M 0x0000008000000000 - 0x00000081FEFFFFFF (8176M used)
[ 6.239931] amdgpu 0000:06:00.0: amdgpu: GART: 512M 0x0000000000000000 - 0x000000001FFFFFFF
[ 6.239941] [drm] Detected VRAM RAM=8176M, BAR=256M
[ 6.239941] [drm] RAM width 256bits GDDR6
[ 6.240024] [TTM] Zone kernel: Available graphics memory: 32904510 KiB
[ 6.240025] [TTM] Zone dma32: Available graphics memory: 2097152 KiB
[ 6.240026] [TTM] Initializing pool allocator
[ 6.240030] [TTM] Initializing DMA pool allocator
[ 6.240068] [drm] amdgpu: 8176M of VRAM memory ready
[ 6.240071] [drm] amdgpu: 8176M of GTT memory ready.
[ 6.240073] [drm] GART: num cpu pages 131072, num gpu pages 131072
[ 6.240244] [drm] PCIE GART of 512M enabled (table at 0x0000008000000000).
[ 6.246903] [drm] Found VCN firmware Version ENC: 1.9 DEC: 5 VEP: 0 Revision: 0
[ 6.246910] [drm] PSP loading VCN firmware
[ 6.280600] EDAC amd64: F17h_M70h detected (node 0).
[ 6.280646] EDAC amd64: Node 0: DRAM ECC disabled.
[ 6.281074] mousedev: PS/2 mouse device common for all mice
[ 6.319259] hub 1-2.4.4.1:1.0: USB hub found
[ 6.319447] hub 1-2.4.4.1:1.0: 4 ports detected
[ 6.360017] usb 1-2.4.1.2: new low-speed USB device number 15 using xhci_hcd
[ 6.398445] r8169 0000:07:00.0 enp7s0: renamed from eth0
[ 6.407449] EDAC amd64: F17h_M70h detected (node 0).
[ 6.407507] EDAC amd64: Node 0: DRAM ECC disabled.
[ 6.453376] random: crng init done
[ 6.511144] usb 1-2.4.1.2: New USB device found, idVendor=1a2c, idProduct=2d23, bcdDevice= 1.10
[ 6.511148] usb 1-2.4.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 6.511150] usb 1-2.4.1.2: Product: USB Keyboard
[ 6.511152] usb 1-2.4.1.2: Manufacturer: USB
[ 6.566686] usb 1-2.4.1.4.3: new full-speed USB device number 16 using xhci_hcd
[ 6.574813] EDAC amd64: F17h_M70h detected (node 0).
[ 6.574869] EDAC amd64: Node 0: DRAM ECC disabled.
[ 6.613316] input: USB USB Keyboard as /devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:03:08.0/0000:08:00.1/usb1/1-2/1-2.4/1-2.4.1/1-2.4.1.2/1-2.4.1.2:1.0/0003:1A2C:2D23.0007/input/input34
[ 6.666828] hid-generic 0003:1A2C:2D23.0007: input,hidraw3: USB HID v1.10 Keyboard [USB USB Keyboard] on usb-0000:08:00.1-2.4.1.2/input0
[ 6.670322] input: USB USB Keyboard Consumer Control as /devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:03:08.0/0000:08:00.1/usb1/1-2/1-2.4/1-2.4.1/1-2.4.1.2/1-2.4.1.2:1.1/0003:1A2C:2D23.0008/input/input35
[ 6.681421] EDAC amd64: F17h_M70h detected (node 0).
[ 6.681475] EDAC amd64: Node 0: DRAM ECC disabled.
[ 6.726756] input: USB USB Keyboard System Control as /devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:03:08.0/0000:08:00.1/usb1/1-2/1-2.4/1-2.4.1/1-2.4.1.2/1-2.4.1.2:1.1/0003:1A2C:2D23.0008/input/input36
[ 6.735209] usb 1-2.4.1.4.3: New USB device found, idVendor=0451, idProduct=ca01, bcdDevice= 1.00
[ 6.735212] usb 1-2.4.1.4.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 6.735213] usb 1-2.4.1.4.3: Product: Texas Instruments USBtoI2C Solution
[ 6.735214] usb 1-2.4.1.4.3: Manufacturer: Texas Instruments
[ 6.735215] usb 1-2.4.1.4.3: SerialNumber: \x08\x08\x08\x08\x04\x04\x04\x04
[ 6.776682] usb 1-2.4.4.2: new full-speed USB device number 17 using xhci_hcd
[ 6.814002] EDAC amd64: F17h_M70h detected (node 0).
[ 6.814053] EDAC amd64: Node 0: DRAM ECC disabled.
[ 6.846245] hid-generic 0003:0451:CA01.0009: hiddev1,hidraw5: USB HID v1.00 Device [Texas Instruments Texas Instruments USBtoI2C Solution] on usb-0000:08:00.1-2.4.1.4.3/input0
[ 6.880184] hid-generic 0003:1A2C:2D23.0008: input,hidraw6: USB HID v1.10 Device [USB USB Keyboard] on usb-0000:08:00.1-2.4.1.2/input1
[ 6.947078] usb 1-2.4.4.2: New USB device found, idVendor=0d8c, idProduct=0005, bcdDevice= 1.00
[ 6.947081] usb 1-2.4.4.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 6.947082] usb 1-2.4.4.2: Product: Blue Snowball
[ 6.947083] usb 1-2.4.4.2: Manufacturer: BLUE MICROPHONE
[ 6.947084] usb 1-2.4.4.2: SerialNumber: 201306
[ 6.961379] EDAC amd64: F17h_M70h detected (node 0).
[ 6.961430] EDAC amd64: Node 0: DRAM ECC disabled.
[ 6.970020] [drm] reserve 0x900000 from 0x81fe400000 for PSP TMR
[ 7.000015] usb 1-2.4.4.1.4: new high-speed USB device number 18 using xhci_hcd
[ 7.075457] input: Logitech K400 Plus as /devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:03:08.0/0000:08:00.1/usb1/1-1/1-1.4/1-1.4.4/1-1.4.4.2/1-1.4.4.2:1.2/0003:046D:C52B.0004/0003:046D:404D.0006/input/input37
[ 7.075623] logitech-hidpp-device 0003:046D:404D.0006: input,hidraw2: USB HID v1.11 Keyboard [Logitech K400 Plus] on usb-0000:08:00.1-1.4.4.2/input2:1
[ 7.121451] EDAC amd64: F17h_M70h detected (node 0).
[ 7.121507] EDAC amd64: Node 0: DRAM ECC disabled.
[ 7.133357] amdgpu 0000:06:00.0: amdgpu: RAS: optional ras ta ucode is not available
[ 7.135565] usb 1-2.4.4.1.4: New USB device found, idVendor=0451, idProduct=8142, bcdDevice= 1.00
[ 7.135568] usb 1-2.4.4.1.4: New USB device strings: Mfr=0, Product=0, SerialNumber=1
[ 7.135569] usb 1-2.4.4.1.4: SerialNumber: 970000896538
[ 7.153396] amdgpu: use vbios provided pptable
[ 7.153474] amdgpu: smc_dpm_info table revision(format.content): 4.5
[ 7.198702] amdgpu: SMU is initialized successfully!
[ 7.199021] [drm] Display Core initialized with v3.2.84!
[ 7.200216] snd_hda_intel 0000:06:00.1: bound 0000:06:00.0 (ops amdgpu_dm_audio_component_bind_ops [amdgpu])
[ 7.215296] hub 1-2.4.4.1.4:1.0: USB hub found
[ 7.215565] hub 1-2.4.4.1.4:1.0: 4 ports detected
[ 7.240857] EDAC amd64: F17h_M70h detected (node 0).
[ 7.240908] EDAC amd64: Node 0: DRAM ECC disabled.
[ 7.286361] [drm] DM_MST: Differing MST start on aconnector: 00000000b757a933 [id: 74]
[ 7.286581] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 7.289188] [drm] kiq ring mec 2 pipe 1 q 0
[ 7.301174] [drm] VCN decode and encode initialized successfully(under DPG Mode).
[ 7.302232] [drm] JPEG decode initialized successfully.
[ 7.303645] kfd kfd: Allocated 3969056 bytes on gart
[ 7.304402] Virtual CRAT table created for GPU
[ 7.304523] amdgpu: Topology: Add dGPU node [0x731f:0x1002]
[ 7.304525] kfd kfd: added device 1002:731f
[ 7.304528] amdgpu 0000:06:00.0: amdgpu: SE 2, SH per SE 2, CU per SH 10, active_cu_number 40
[ 7.304631] amdgpu 0000:06:00.0: [drm] Cannot find any crtc or sizes
[ 7.304755] amdgpu 0000:06:00.0: amdgpu: ring gfx_0.0.0 uses VM inv eng 0 on hub 0
[ 7.304757] amdgpu 0000:06:00.0: amdgpu: ring comp_1.0.0 uses VM inv eng 1 on hub 0
[ 7.304758] amdgpu 0000:06:00.0: amdgpu: ring comp_1.1.0 uses VM inv eng 4 on hub 0
[ 7.304759] amdgpu 0000:06:00.0: amdgpu: ring comp_1.2.0 uses VM inv eng 5 on hub 0
[ 7.304761] amdgpu 0000:06:00.0: amdgpu: ring comp_1.3.0 uses VM inv eng 6 on hub 0
[ 7.304762] amdgpu 0000:06:00.0: amdgpu: ring comp_1.0.1 uses VM inv eng 7 on hub 0
[ 7.304764] amdgpu 0000:06:00.0: amdgpu: ring comp_1.1.1 uses VM inv eng 8 on hub 0
[ 7.304765] amdgpu 0000:06:00.0: amdgpu: ring comp_1.2.1 uses VM inv eng 9 on hub 0
[ 7.304766] amdgpu 0000:06:00.0: amdgpu: ring comp_1.3.1 uses VM inv eng 10 on hub 0
[ 7.304768] amdgpu 0000:06:00.0: amdgpu: ring kiq_2.1.0 uses VM inv eng 11 on hub 0
[ 7.304769] amdgpu 0000:06:00.0: amdgpu: ring sdma0 uses VM inv eng 12 on hub 0
[ 7.304771] amdgpu 0000:06:00.0: amdgpu: ring sdma1 uses VM inv eng 13 on hub 0
[ 7.304772] amdgpu 0000:06:00.0: amdgpu: ring vcn_dec uses VM inv eng 0 on hub 1
[ 7.304774] amdgpu 0000:06:00.0: amdgpu: ring vcn_enc0 uses VM inv eng 1 on hub 1
[ 7.304775] amdgpu 0000:06:00.0: amdgpu: ring vcn_enc1 uses VM inv eng 4 on hub 1
[ 7.304777] amdgpu 0000:06:00.0: amdgpu: ring jpeg_dec uses VM inv eng 5 on hub 1
[ 7.313867] [drm] Initialized amdgpu 3.38.0 20150101 for 0000:06:00.0 on minor 0
[ 7.313979] checking generic (c0000000 300000) vs hw (c0000000 10000000)
[ 7.313980] fb0: switching to amdgpudrmfb from EFI VGA
[ 7.314041] Console: switching to colour dummy device 80x25
[ 7.314076] amdgpu 0000:0d:00.0: vgaarb: deactivate vga console
[ 7.314176] [drm] initializing kernel modesetting (NAVI10 0x1002:0x731F 0x1DA2:0xE410 0xC1).
[ 7.314179] amdgpu 0000:0d:00.0: amdgpu: Trusted Memory Zone (TMZ) feature disabled as experimental (default)
[ 7.314197] [drm] register mmio base: 0xFCB00000
[ 7.314198] [drm] register mmio size: 524288
[ 7.335150] [drm] add ip block number 0 <nv_common>
[ 7.335151] [drm] add ip block number 1 <gmc_v10_0>
[ 7.335152] [drm] add ip block number 2 <navi10_ih>
[ 7.335153] [drm] add ip block number 3 <psp>
[ 7.335154] [drm] add ip block number 4 <smu>
[ 7.335155] [drm] add ip block number 5 <dm>
[ 7.335156] [drm] add ip block number 6 <gfx_v10_0>
[ 7.335157] [drm] add ip block number 7 <sdma_v5_0>
[ 7.335158] [drm] add ip block number 8 <vcn_v2_0>
[ 7.335158] [drm] add ip block number 9 <jpeg_v2_0>
[ 7.335186] amdgpu 0000:0d:00.0: No more image in the PCI ROM
[ 7.335208] amdgpu: ATOM BIOS: 113-410XT-UO4
[ 7.335216] [drm] VCN decode is enabled in VM mode
[ 7.335217] [drm] VCN encode is enabled in VM mode
[ 7.335218] [drm] JPEG decode is enabled in VM mode
[ 7.335241] [drm] vm size is 262144 GB, 4 levels, block size is 9-bit, fragment size is 9-bit
[ 7.335247] amdgpu 0000:0d:00.0: amdgpu: VRAM: 8176M 0x0000008000000000 - 0x00000081FEFFFFFF (8176M used)
[ 7.335249] amdgpu 0000:0d:00.0: amdgpu: GART: 512M 0x0000000000000000 - 0x000000001FFFFFFF
[ 7.335258] [drm] Detected VRAM RAM=8176M, BAR=256M
[ 7.335259] [drm] RAM width 256bits GDDR6
[ 7.335291] [drm] amdgpu: 8176M of VRAM memory ready
[ 7.335295] [drm] amdgpu: 8176M of GTT memory ready.
[ 7.335297] [drm] GART: num cpu pages 131072, num gpu pages 131072
[ 7.335439] [drm] PCIE GART of 512M enabled (table at 0x0000008000300000).
[ 7.337461] [drm] Found VCN firmware Version ENC: 1.9 DEC: 5 VEP: 0 Revision: 0
[ 7.337467] [drm] PSP loading VCN firmware
[ 7.374064] EDAC amd64: F17h_M70h detected (node 0).
[ 7.374118] EDAC amd64: Node 0: DRAM ECC disabled.
[ 7.520576] EDAC amd64: F17h_M70h detected (node 0).
[ 7.520630] EDAC amd64: Node 0: DRAM ECC disabled.
[ 7.600658] EDAC amd64: F17h_M70h detected (node 0).
[ 7.600710] EDAC amd64: Node 0: DRAM ECC disabled.
[ 7.640044] usb 1-2.4.4.1.4.2: new high-speed USB device number 19 using xhci_hcd
[ 7.720554] EDAC amd64: F17h_M70h detected (node 0).
[ 7.720602] EDAC amd64: Node 0: DRAM ECC disabled.
[ 7.808698] usb 1-2.4.4.1.4.2: New USB device found, idVendor=32e4, idProduct=9422, bcdDevice= 1.00
[ 7.808701] usb 1-2.4.4.1.4.2: New USB device strings: Mfr=2, Product=1, SerialNumber=3
[ 7.808702] usb 1-2.4.4.1.4.2: Product: H264 USB Camera
[ 7.808703] usb 1-2.4.4.1.4.2: Manufacturer: H264 USB Camera
[ 7.808704] usb 1-2.4.4.1.4.2: SerialNumber: 2020032801
[ 7.906683] [drm] reserve 0x900000 from 0x81fe400000 for PSP TMR
[ 7.975919] [drm] fb mappable at 0xE01CA000
[ 7.975920] [drm] vram apper at 0xE0000000
[ 7.975921] [drm] size 9216000
[ 7.975921] [drm] fb depth is 24
[ 7.975922] [drm] pitch is 7680
[ 8.012162] hid-generic 0003:0D8C:0005.000A: No inputs registered, leaving
[ 8.012215] hid-generic 0003:0D8C:0005.000A: hidraw7: USB HID v1.11 Device [BLUE MICROPHONE Blue Snowball ] on usb-0000:08:00.1-2.4.4.2/input2
[ 8.035576] usb 1-2.4.4.1.4.2: 4:1: cannot get freq at ep 0x84
[ 8.070015] amdgpu 0000:0d:00.0: amdgpu: RAS: optional ras ta ucode is not available
[ 8.086677] usb 1-2.4.4.3: new high-speed USB device number 20 using xhci_hcd
[ 8.090046] amdgpu: use vbios provided pptable
[ 8.090100] amdgpu: smc_dpm_info table revision(format.content): 4.5
[ 8.134424] amdgpu: SMU is initialized successfully!
[ 8.134649] [drm] Display Core initialized with v3.2.84!
[ 8.158979] snd_hda_intel 0000:0d:00.1: bound 0000:0d:00.0 (ops amdgpu_dm_audio_component_bind_ops [amdgpu])
[ 8.178425] usb 1-2.4.4.3: New USB device found, idVendor=0451, idProduct=8142, bcdDevice= 1.00
[ 8.178428] usb 1-2.4.4.3: New USB device strings: Mfr=0, Product=0, SerialNumber=1
[ 8.178429] usb 1-2.4.4.3: SerialNumber: F5000851FE0F
[ 8.180161] usbcore: registered new interface driver snd-usb-audio
[ 8.239209] hub 1-2.4.4.3:1.0: USB hub found
[ 8.239419] hub 1-2.4.4.3:1.0: 4 ports detected
[ 8.280045] usb 1-2.4.4.1.4.3: new full-speed USB device number 21 using xhci_hcd
[ 8.329738] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 8.331557] [drm] kiq ring mec 2 pipe 1 q 0
[ 8.341082] [drm] VCN decode and encode initialized successfully(under DPG Mode).
[ 8.341221] [drm] JPEG decode initialized successfully.
[ 8.341768] kfd kfd: Allocated 3969056 bytes on gart
[ 8.341931] Virtual CRAT table created for GPU
[ 8.342072] amdgpu: Topology: Add dGPU node [0x731f:0x1002]
[ 8.342073] kfd kfd: added device 1002:731f
[ 8.342075] amdgpu 0000:0d:00.0: amdgpu: SE 2, SH per SE 2, CU per SH 10, active_cu_number 40
[ 8.344220] [drm] fb mappable at 0xC04CA000
[ 8.344221] [drm] vram apper at 0xC0000000
[ 8.344221] [drm] size 33177600
[ 8.344221] [drm] fb depth is 24
[ 8.344221] [drm] pitch is 15360
[ 8.425080] usb 1-2.4.4.1.4.3: New USB device found, idVendor=0451, idProduct=ca01, bcdDevice= 1.00
[ 8.425083] usb 1-2.4.4.1.4.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 8.425084] usb 1-2.4.4.1.4.3: Product: Texas Instruments USBtoI2C Solution
[ 8.425085] usb 1-2.4.4.1.4.3: Manufacturer: Texas Instruments
[ 8.425086] usb 1-2.4.4.1.4.3: SerialNumber: \x08\x08\x08\x08\x04\x04\x04\x04
[ 8.509272] hid-generic 0003:0451:CA01.000B: hiddev2,hidraw8: USB HID v1.00 Device [Texas Instruments Texas Instruments USBtoI2C Solution] on usb-0000:08:00.1-2.4.4.1.4.3/input0
[ 8.550775] videodev: Linux video capture interface: v2.00
[ 8.572971] uvcvideo: Found UVC 1.00 device H264 USB Camera (32e4:9422)
[ 8.583352] usb 1-2.4.4.3.1: new low-speed USB device number 22 using xhci_hcd
[ 8.618114] uvcvideo 1-2.4.4.1.4.2:1.0: Entity type for entity Extension 4 was not initialized!
[ 8.618116] uvcvideo 1-2.4.4.1.4.2:1.0: Entity type for entity Extension 3 was not initialized!
[ 8.618118] uvcvideo 1-2.4.4.1.4.2:1.0: Entity type for entity Processing 2 was not initialized!
[ 8.618119] uvcvideo 1-2.4.4.1.4.2:1.0: Entity type for entity Camera 1 was not initialized!
[ 8.618189] input: H264 USB Camera: USB Camera as /devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:03:08.0/0000:08:00.1/usb1/1-2/1-2.4/1-2.4.4/1-2.4.4.1/1-2.4.4.1.4/1-2.4.4.1.4.2/1-2.4.4.1.4.2:1.0/input/input39
[ 8.618257] usbcore: registered new interface driver uvcvideo
[ 8.618258] USB Video Class driver (1.1.1)
[ 8.691112] usb 1-2.4.4.3.1: New USB device found, idVendor=04b3, idProduct=3025, bcdDevice= 1.00
[ 8.691115] usb 1-2.4.4.3.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 8.691116] usb 1-2.4.4.3.1: Product: USB NetVista Full Width Keyboard.
[ 8.691117] usb 1-2.4.4.3.1: Manufacturer: LITE-ON Technology
[ 8.764343] input: LITE-ON Technology USB NetVista Full Width Keyboard. as /devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:03:08.0/0000:08:00.1/usb1/1-2/1-2.4/1-2.4.4/1-2.4.4.3/1-2.4.4.3.1/1-2.4.4.3.1:1.0/0003:04B3:3025.000C/input/input40
[ 8.820179] hid-generic 0003:04B3:3025.000C: input,hidraw9: USB HID v1.10 Keyboard [LITE-ON Technology USB NetVista Full Width Keyboard.] on usb-0000:08:00.1-2.4.4.3.1/input0
[ 8.893366] usb 1-2.4.4.3.2: new full-speed USB device number 23 using xhci_hcd
[ 8.897908] Console: switching to colour frame buffer device 240x75
[ 8.918137] amdgpu 0000:06:00.0: fb0: amdgpudrmfb frame buffer device
[ 8.918231] fbcon: amdgpudrmfb (fb1) is primary device
[ 8.918233] fbcon: Remapping primary device, fb1, to tty 1-63
[ 9.003071] usb 1-2.4.4.3.2: New USB device found, idVendor=046d, idProduct=c247, bcdDevice=82.00
[ 9.003074] usb 1-2.4.4.3.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 9.003075] usb 1-2.4.4.3.2: Product: G100s Optical Gaming Mouse
[ 9.003076] usb 1-2.4.4.3.2: Manufacturer: Logitech
[ 9.048230] input: Logitech G100s Optical Gaming Mouse as /devices/pci0000:00/0000:00:01.2/0000:02:00.0/0000:03:08.0/0000:08:00.1/usb1/1-2/1-2.4/1-2.4.4/1-2.4.4.3/1-2.4.4.3.2/1-2.4.4.3.2:1.0/0003:046D:C247.000D/input/input41
[ 9.048326] hid-generic 0003:046D:C247.000D: input,hidraw10: USB HID v1.10 Mouse [Logitech G100s Optical Gaming Mouse] on usb-0000:08:00.1-2.4.4.3.2/input0
[ 9.120031] usb 1-2.4.4.3.4: new high-speed USB device number 24 using xhci_hcd
[ 9.212554] usb 1-2.4.4.3.4: New USB device found, idVendor=0451, idProduct=8142, bcdDevice= 1.00
[ 9.212556] usb 1-2.4.4.3.4: New USB device strings: Mfr=0, Product=0, SerialNumber=1
[ 9.212557] usb 1-2.4.4.3.4: SerialNumber: 46000071FE0F
[ 9.263219] hub 1-2.4.4.3.4:1.0: USB hub found
[ 9.263411] hub 1-2.4.4.3.4:1.0: 4 ports detected
[ 9.606946] usb 1-2.4.4.3.4.3: new full-speed USB device number 25 using xhci_hcd
[ 9.730043] usb 1-2.4.4.3.4.3: New USB device found, idVendor=0451, idProduct=ca01, bcdDevice= 1.00
[ 9.730045] usb 1-2.4.4.3.4.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 9.730046] usb 1-2.4.4.3.4.3: Product: Texas Instruments USBtoI2C Solution
[ 9.730047] usb 1-2.4.4.3.4.3: Manufacturer: Texas Instruments
[ 9.730048] usb 1-2.4.4.3.4.3: SerialNumber: \x08\x08\x08\x08\x04\x04\x04\x04
[ 9.822290] hid-generic 0003:0451:CA01.000E: hiddev3,hidraw11: USB HID v1.00 Device [Texas Instruments Texas Instruments USBtoI2C Solution] on usb-0000:08:00.1-2.4.4.3.4.3/input0
[ 11.234364] amdgpu 0000:0d:00.0: fb1: amdgpudrmfb frame buffer device
[ 11.234455] amdgpu 0000:0d:00.0: amdgpu: ring gfx_0.0.0 uses VM inv eng 0 on hub 0
[ 11.234457] amdgpu 0000:0d:00.0: amdgpu: ring comp_1.0.0 uses VM inv eng 1 on hub 0
[ 11.234458] amdgpu 0000:0d:00.0: amdgpu: ring comp_1.1.0 uses VM inv eng 4 on hub 0
[ 11.234459] amdgpu 0000:0d:00.0: amdgpu: ring comp_1.2.0 uses VM inv eng 5 on hub 0
[ 11.234461] amdgpu 0000:0d:00.0: amdgpu: ring comp_1.3.0 uses VM inv eng 6 on hub 0
[ 11.234467] amdgpu 0000:0d:00.0: amdgpu: ring comp_1.0.1 uses VM inv eng 7 on hub 0
[ 11.234468] amdgpu 0000:0d:00.0: amdgpu: ring comp_1.1.1 uses VM inv eng 8 on hub 0
[ 11.234470] amdgpu 0000:0d:00.0: amdgpu: ring comp_1.2.1 uses VM inv eng 9 on hub 0
[ 11.234471] amdgpu 0000:0d:00.0: amdgpu: ring comp_1.3.1 uses VM inv eng 10 on hub 0
[ 11.234472] amdgpu 0000:0d:00.0: amdgpu: ring kiq_2.1.0 uses VM inv eng 11 on hub 0
[ 11.234473] amdgpu 0000:0d:00.0: amdgpu: ring sdma0 uses VM inv eng 12 on hub 0
[ 11.234474] amdgpu 0000:0d:00.0: amdgpu: ring sdma1 uses VM inv eng 13 on hub 0
[ 11.234476] amdgpu 0000:0d:00.0: amdgpu: ring vcn_dec uses VM inv eng 0 on hub 1
[ 11.234477] amdgpu 0000:0d:00.0: amdgpu: ring vcn_enc0 uses VM inv eng 1 on hub 1
[ 11.234478] amdgpu 0000:0d:00.0: amdgpu: ring vcn_enc1 uses VM inv eng 4 on hub 1
[ 11.234479] amdgpu 0000:0d:00.0: amdgpu: ring jpeg_dec uses VM inv eng 5 on hub 1
[ 11.234954] [drm] Initialized amdgpu 3.38.0 20150101 for 0000:0d:00.0 on minor 1
[ 12.520975] input: USB USB Keyboard Consumer Control as /devices/virtual/input/input42
[ 12.520984] input: Logitech K400 Plus as /devices/virtual/input/input43
[ 12.520990] input: LITE-ON Technology USB NetVista Full Width Keyboard. as /devices/virtual/input/input44
[ 12.521250] input: USB USB Keyboard as /devices/virtual/input/input45
[ 12.547495] usb 1-2.4.4.1.4.2: 4:1: cannot get freq at ep 0x84
[ 12.580029] Generic FE-GE Realtek PHY r8169-700:00: attached PHY driver [Generic FE-GE Realtek PHY] (mii_bus:phy_addr=r8169-700:00, irq=IGNORE)
[ 12.611370] usb 1-2.4.4.1.4.2: 4:1: cannot get freq at ep 0x84
[ 12.666725] amdgpu 0000:06:00.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=none:owns=none
[ 12.666726] amdgpu 0000:0d:00.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=none:owns=io+mem
[ 12.726778] r8169 0000:07:00.0 enp7s0: Link is Down
[ 16.238675] IPv6: ADDRCONF(NETDEV_CHANGE): enp7s0: link becomes ready
[ 16.238791] r8169 0000:07:00.0 enp7s0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 18.095925] retire_capture_urb: 40 callbacks suppressedThe best solution to a problem is usually the easiest one.
Offline
#4 2020-12-05 16:03:59
- qdii
- Member
- Registered: 2020-12-05
- Posts: 2
Re: Multiple stability problems with DP1.2/MST on AMDGPU
I'm experiencing similar symptoms (slow refresh rate, many 'client bug: event processing laggind behind') with a slightly different setup: laptop ↔ docking station ↔ eGPU
The laptop is connected to a Thunderbolt 3 docking station (SD5200T) itself connected to a eGPU (Razer Core X). The eGPU is connected to the monitors with DP 1.2.
I discarded picom being the problem as the problem persists after killing it.
I also discarded the eGPU and Docking Station being the problems as I can dual boot on Windows and everything works fine.
I'm running Xorg with amdgpu driver, I'll follow-up by installing wayland and see if the problem is reproducible there.
Last edited by qdii (2020-12-05 16:05:48)
Offline
#5 2020-12-06 14:32:35
- Lone_Wolf
- Administrator
- From: Netherlands, Europe
- Registered: 2005-10-04
- Posts: 15,086
Re: Multiple stability problems with DP1.2/MST on AMDGPU
qdii wrote:
I also discarded the eGPU and Docking Station being the problems as I can dual boot on Windows and everything works fine.
The razor core X / thunderbolt 3 combo may cause problems on linux , see https://bbs.archlinux.org/viewtopic.php?id=261303 .
@DexterLB :
Sorry, forgot I hadn't replied.
dmesg has very little that stands out except these
[ 12.547495] usb 1-2.4.4.1.4.2: 4:1: cannot get freq at ep 0x84The xorg log "event processing lagging behind" are reported by usb devices.
It may be a red herring, but usb 1-2.4.4.1.4.2 appears to be a camera device .
Can you disconnect or disable the camera ?
[ 7.640044] usb 1-2.4.4.1.4.2: new high-speed USB device number 19 using xhci_hcd
[ 7.720554] EDAC amd64: F17h_M70h detected (node 0).
[ 7.720602] EDAC amd64: Node 0: DRAM ECC disabled.
[ 7.808698] usb 1-2.4.4.1.4.2: New USB device found, idVendor=32e4, idProduct=9422, bcdDevice= 1.00
[ 7.808701] usb 1-2.4.4.1.4.2: New USB device strings: Mfr=2, Product=1, SerialNumber=3
[ 7.808702] usb 1-2.4.4.1.4.2: Product: H264 USB Camera
[ 7.808703] usb 1-2.4.4.1.4.2: Manufacturer: H264 USB Camera
[ 7.808704] usb 1-2.4.4.1.4.2: SerialNumber: 2020032801Disliking systemd intensely, but not satisfied with alternatives so focusing on taming systemd.
clean chroot building not flexible enough ?
Try clean chroot manager by graysky
Offline
#6 2020-12-06 17:50:07
- mkkot
- Member
- From: Poland
- Registered: 2009-12-20
- Posts: 288
Re: Multiple stability problems with DP1.2/MST on AMDGPU
Welcome to hell of too new radeon devices on Linux. I have the same issue with random DP numbers (actually we all have):
https://lists.freedesktop.org/archives/ … 84818.html
And similar problem with multiple screens and xrandr that hangs X and makes driver crash:
https://bugzilla.kernel.org/show_bug.cgi?id=210303
I'm updating kernel on each release in hope someone fixes it.
Offline
#7 2021-07-08 07:22:11
- drakanio
- Member
- Registered: 2021-07-01
- Posts: 4
Re: Multiple stability problems with DP1.2/MST on AMDGPU
mkkot wrote:
Welcome to hell of too new radeon devices on Linux. I have the same issue with random DP numbers (actually we all have):
https://lists.freedesktop.org/archives/ … 84818.html
Do you have any solution now for this?
The random DP numbers destroy every reboot/sleep my setup 
Offline
#8 2021-07-09 10:31:18
- mkkot
- Member
- From: Poland
- Registered: 2009-12-20
- Posts: 288
Re: Multiple stability problems with DP1.2/MST on AMDGPU
Actually I do. This seems to be determined by faulty firmware of U2415. Some time ago I bought Dells P3421W and the problem disappeared.
Offline
#9 2021-07-09 18:34:27
- drakanio
- Member
- Registered: 2021-07-01
- Posts: 4
Re: Multiple stability problems with DP1.2/MST on AMDGPU
Damn! I have the U2515H... you think this is a hardware problem with linux?
Offline
#10 2021-07-09 22:32:57
- mkkot
- Member
- From: Poland
- Registered: 2009-12-20
- Posts: 288
Re: Multiple stability problems with DP1.2/MST on AMDGPU
Hard to say. Now my wife uses it with Archlinux without any issues, but she's having a laptop with Intel GPU and no daisy chaining.
Anyway, my problem with this monitor was that it sometimes didn't turn on after it was blanked by power saving mode (when connected via DP). This is gone with new model. Of course daisy chaining was a nightmare too. I could never tell if both monitors will resume or only one or none.
Offline