You are not logged in.
Pages: 1
For the last 2 days my machine has been emitting a high-pitched whine and rebooting. Here's how it has happened both times:
I turn the machine on, it boots fine. I log in and start X, but before X loads completely my machine emits a high-pitched whine and reboots. Upon rebooting, the machine will get to the point of mounting local filesystems, it will find that my xfs filesystem (not on the same drive as my root partition) is not clean, presumably because my machine just rebooted without unmounting it cleanly). At this point my machine will emit the same whine sound and reboot. Upon subsequent reboots it will make it to the point of mounting local filesystems, find the xfs system not clean, whine, and reboot again. If I log in to my gentoo installation on a different partition, and then immediately reboot the machine, it boots into ARCH fine, I get into X, and all is well. Very frustrating.
Log:
Nov 11 10:09:47 uncle_bilbo Linux version 2.6.18-ARCH (root@uncle_bilbo) (gcc version 4.1.1) #3 PREEMPT Sun Oct 29 10:42:52 PST 2006
Nov 11 10:09:47 uncle_bilbo BIOS-provided physical RAM map:
Nov 11 10:09:47 uncle_bilbo BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
Nov 11 10:09:47 uncle_bilbo BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
Nov 11 10:09:47 uncle_bilbo BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
Nov 11 10:09:47 uncle_bilbo BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
Nov 11 10:09:47 uncle_bilbo BIOS-e820: 000000001fff0000 - 000000001fff8000 (ACPI data)
Nov 11 10:09:47 uncle_bilbo BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS)
Nov 11 10:09:47 uncle_bilbo BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
Nov 11 10:09:47 uncle_bilbo BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
Nov 11 10:09:47 uncle_bilbo BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
Nov 11 10:09:47 uncle_bilbo 511MB LOWMEM available.
Nov 11 10:09:47 uncle_bilbo DMI 2.3 present.
Nov 11 10:09:47 uncle_bilbo ACPI: PM-Timer IO Port: 0x808
Nov 11 10:09:47 uncle_bilbo Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
Nov 11 10:09:47 uncle_bilbo Detected 1673.830 MHz processor.
Nov 11 10:09:47 uncle_bilbo Built 1 zonelists. Total pages: 131056
Nov 11 10:09:47 uncle_bilbo Kernel command line: BOOT_IMAGE=arch.v ro root=304
Nov 11 10:09:47 uncle_bilbo Enabling fast FPU save and restore... done.
Nov 11 10:09:47 uncle_bilbo Enabling unmasked SIMD FPU exception support... done.
Nov 11 10:09:47 uncle_bilbo Initializing CPU#0
Nov 11 10:09:47 uncle_bilbo PID hash table entries: 2048 (order: 11, 8192 bytes)
Nov 11 10:09:47 uncle_bilbo Console: colour VGA+ 80x25
Nov 11 10:09:47 uncle_bilbo Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Nov 11 10:09:47 uncle_bilbo Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Nov 11 10:09:47 uncle_bilbo Memory: 515656k/524224k available (2393k kernel code, 8016k reserved, 696k data, 172k init, 0k highmem)
Nov 11 10:09:47 uncle_bilbo Checking if this processor honours the WP bit even in supervisor mode... Ok.
Nov 11 10:09:47 uncle_bilbo Calibrating delay using timer specific routine.. 3350.68 BogoMIPS (lpj=6701373)
Nov 11 10:09:47 uncle_bilbo Security Framework v1.0.0 initialized
Nov 11 10:09:47 uncle_bilbo Mount-cache hash table entries: 512
Nov 11 10:09:47 uncle_bilbo CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
Nov 11 10:09:47 uncle_bilbo CPU: L2 Cache: 256K (64 bytes/line)
Nov 11 10:09:47 uncle_bilbo Intel machine check architecture supported.
Nov 11 10:09:47 uncle_bilbo Intel machine check reporting enabled on CPU#0.
Nov 11 10:09:47 uncle_bilbo CPU: AMD Athlon(tm) XP 2000+ stepping 01
Nov 11 10:09:47 uncle_bilbo Checking 'hlt' instruction... OK.
Nov 11 10:09:47 uncle_bilbo ACPI: Core revision 20060707
Nov 11 10:09:47 uncle_bilbo ACPI: setting ELCR to 0200 (from 0c00)
Nov 11 10:09:47 uncle_bilbo NET: Registered protocol family 16
Nov 11 10:09:47 uncle_bilbo ACPI: bus type pci registered
Nov 11 10:09:47 uncle_bilbo PCI: PCI BIOS revision 2.10 entry at 0xfdb01, last bus=1
Nov 11 10:09:47 uncle_bilbo PCI: Using configuration type 1
Nov 11 10:09:47 uncle_bilbo Setting up standard PCI resources
Nov 11 10:09:47 uncle_bilbo ACPI: Interpreter enabled
Nov 11 10:09:47 uncle_bilbo ACPI: Using PIC for interrupt routing
Nov 11 10:09:47 uncle_bilbo ACPI: PCI Root Bridge [PCI0] (0000:00)
Nov 11 10:09:47 uncle_bilbo ACPI: Power Resource [URP1] (off)
Nov 11 10:09:47 uncle_bilbo ACPI: Power Resource [URP2] (off)
Nov 11 10:09:47 uncle_bilbo ACPI: Power Resource [FDDP] (off)
Nov 11 10:09:47 uncle_bilbo ACPI: Power Resource [LPTP] (off)
Nov 11 10:09:47 uncle_bilbo ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
Nov 11 10:09:47 uncle_bilbo ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
Nov 11 10:09:47 uncle_bilbo ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
Nov 11 10:09:47 uncle_bilbo ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 12 14 15)
Nov 11 10:09:47 uncle_bilbo Linux Plug and Play Support v0.97 (c) Adam Belay
Nov 11 10:09:47 uncle_bilbo pnp: PnP ACPI init
Nov 11 10:09:47 uncle_bilbo pnp: PnP ACPI: found 13 devices
Nov 11 10:09:47 uncle_bilbo PCI: Using ACPI for IRQ routing
Nov 11 10:09:47 uncle_bilbo PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
Nov 11 10:09:47 uncle_bilbo PCI: Bridge: 0000:00:01.0
Nov 11 10:09:47 uncle_bilbo IO window: disabled.
Nov 11 10:09:47 uncle_bilbo MEM window: d9e00000-dbefffff
Nov 11 10:09:47 uncle_bilbo PREFETCH window: c5c00000-d5cfffff
Nov 11 10:09:47 uncle_bilbo NET: Registered protocol family 2
Nov 11 10:09:47 uncle_bilbo IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
Nov 11 10:09:47 uncle_bilbo TCP established hash table entries: 16384 (order: 4, 65536 bytes)
Nov 11 10:09:47 uncle_bilbo TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
Nov 11 10:09:47 uncle_bilbo TCP: Hash tables configured (established 16384 bind 8192)
Nov 11 10:09:47 uncle_bilbo TCP reno registered
Nov 11 10:09:47 uncle_bilbo VFS: Disk quotas dquot_6.5.1
Nov 11 10:09:47 uncle_bilbo Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Nov 11 10:09:47 uncle_bilbo Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Nov 11 10:09:47 uncle_bilbo Initializing Cryptographic API
Nov 11 10:09:47 uncle_bilbo io scheduler noop registered
Nov 11 10:09:47 uncle_bilbo io scheduler anticipatory registered
Nov 11 10:09:47 uncle_bilbo io scheduler deadline registered
Nov 11 10:09:47 uncle_bilbo io scheduler cfq registered (default)
Nov 11 10:09:47 uncle_bilbo ACPI: Processor [CPU1] (supports 16 throttling states)
Nov 11 10:09:47 uncle_bilbo platform pc8736x_gpio.0: NatSemi pc8736x GPIO Driver Initializing
Nov 11 10:09:47 uncle_bilbo smapi::smapi_init, ERROR invalid usSmapiID
Nov 11 10:09:47 uncle_bilbo Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
Nov 11 10:09:47 uncle_bilbo serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Nov 11 10:09:47 uncle_bilbo serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Nov 11 10:09:47 uncle_bilbo 00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Nov 11 10:09:47 uncle_bilbo 00:03: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Nov 11 10:09:47 uncle_bilbo RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Nov 11 10:09:47 uncle_bilbo loop: loaded (max 8 devices)
Nov 11 10:09:47 uncle_bilbo Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Nov 11 10:09:47 uncle_bilbo ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Nov 11 10:09:47 uncle_bilbo VP_IDE: IDE controller at PCI slot 0000:00:11.1
Nov 11 10:09:47 uncle_bilbo ACPI: Unable to derive IRQ for device 0000:00:11.1
Nov 11 10:09:47 uncle_bilbo ACPI: PCI Interrupt 0000:00:11.1[A]: no GSI
Nov 11 10:09:47 uncle_bilbo PCI: VIA IRQ fixup for 0000:00:11.1, from 255 to 15
Nov 11 10:09:47 uncle_bilbo VP_IDE: chipset revision 6
Nov 11 10:09:47 uncle_bilbo VP_IDE: not 100% native mode: will probe irqs later
Nov 11 10:09:47 uncle_bilbo VP_IDE: VIA vt8233a (rev 00) IDE UDMA133 controller on pci0000:00:11.1
Nov 11 10:09:47 uncle_bilbo ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
Nov 11 10:09:47 uncle_bilbo ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
Nov 11 10:09:47 uncle_bilbo hda: IC35L040AVVN07-0, ATA DISK drive
Nov 11 10:09:47 uncle_bilbo hdb: ST380011A, ATA DISK drive
Nov 11 10:09:47 uncle_bilbo ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Nov 11 10:09:47 uncle_bilbo hdc: SAMSUNG SP2014N, ATA DISK drive
Nov 11 10:09:47 uncle_bilbo hdd: HL-DT-ST DVDRAM GSA-4160B, ATAPI CD/DVD-ROM drive
Nov 11 10:09:47 uncle_bilbo ide1 at 0x170-0x177,0x376 on irq 15
Nov 11 10:09:47 uncle_bilbo hda: max request size: 128KiB
Nov 11 10:09:47 uncle_bilbo hda: 80418240 sectors (41174 MB) w/1863KiB Cache, CHS=65535/16/63, UDMA(33)
Nov 11 10:09:47 uncle_bilbo hda: cache flushes supported
Nov 11 10:09:47 uncle_bilbo hda: hda1 hda2 hda3 hda4
Nov 11 10:09:47 uncle_bilbo hdb: max request size: 512KiB
Nov 11 10:09:47 uncle_bilbo hdb: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(33)
Nov 11 10:09:47 uncle_bilbo hdb: cache flushes supported
Nov 11 10:09:47 uncle_bilbo hdb: hdb1
Nov 11 10:09:47 uncle_bilbo hdc: max request size: 512KiB
Nov 11 10:09:47 uncle_bilbo hdc: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63, UDMA(100)
Nov 11 10:09:47 uncle_bilbo hdc: cache flushes supported
Nov 11 10:09:47 uncle_bilbo hdc: hdc1
Nov 11 10:09:47 uncle_bilbo hdd: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(66)
Nov 11 10:09:47 uncle_bilbo Uniform CD-ROM driver Revision: 3.20
Nov 11 10:09:47 uncle_bilbo ide-floppy driver 0.99.newide
Nov 11 10:09:47 uncle_bilbo PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
Nov 11 10:09:47 uncle_bilbo serio: i8042 AUX port at 0x60,0x64 irq 12
Nov 11 10:09:47 uncle_bilbo serio: i8042 KBD port at 0x60,0x64 irq 1
Nov 11 10:09:47 uncle_bilbo mice: PS/2 mouse device common for all mice
Nov 11 10:09:47 uncle_bilbo TCP bic registered
Nov 11 10:09:47 uncle_bilbo NET: Registered protocol family 1
Nov 11 10:09:47 uncle_bilbo NET: Registered protocol family 17
Nov 11 10:09:47 uncle_bilbo Using IPI Shortcut mode
Nov 11 10:09:47 uncle_bilbo ACPI: (supports S0 S1 S4 S5)
Nov 11 10:09:47 uncle_bilbo Time: tsc clocksource has been installed.
Nov 11 10:09:47 uncle_bilbo input: AT Translated Set 2 keyboard as /class/input/input0
Nov 11 10:09:47 uncle_bilbo kjournald starting. Commit interval 5 seconds
Nov 11 10:09:47 uncle_bilbo EXT3-fs: mounted filesystem with ordered data mode.
Nov 11 10:09:47 uncle_bilbo VFS: Mounted root (ext3 filesystem) readonly.
Nov 11 10:09:47 uncle_bilbo Freeing unused kernel memory: 172k freed
Nov 11 10:09:47 uncle_bilbo usbcore: registered new driver usbfs
Nov 11 10:09:47 uncle_bilbo usbcore: registered new driver hub
Nov 11 10:09:47 uncle_bilbo USB Universal Host Controller Interface driver v3.0
Nov 11 10:09:47 uncle_bilbo ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
Nov 11 10:09:47 uncle_bilbo ACPI: PCI Interrupt 0000:00:11.2[D] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
Nov 11 10:09:47 uncle_bilbo uhci_hcd 0000:00:11.2: UHCI Host Controller
Nov 11 10:09:47 uncle_bilbo uhci_hcd 0000:00:11.2: new USB bus registered, assigned bus number 1
Nov 11 10:09:47 uncle_bilbo uhci_hcd 0000:00:11.2: irq 10, io base 0x0000d800
Nov 11 10:09:47 uncle_bilbo usb usb1: configuration #1 chosen from 1 choice
Nov 11 10:09:47 uncle_bilbo hub 1-0:1.0: USB hub found
Nov 11 10:09:47 uncle_bilbo hub 1-0:1.0: 2 ports detected
Nov 11 10:09:47 uncle_bilbo parport: PnPBIOS parport detected.
Nov 11 10:09:47 uncle_bilbo parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
Nov 11 10:09:47 uncle_bilbo ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
Nov 11 10:09:47 uncle_bilbo ACPI: PCI Interrupt 0000:00:14.2[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
Nov 11 10:09:47 uncle_bilbo ehci_hcd 0000:00:14.2: EHCI Host Controller
Nov 11 10:09:47 uncle_bilbo ehci_hcd 0000:00:14.2: new USB bus registered, assigned bus number 2
Nov 11 10:09:47 uncle_bilbo ehci_hcd 0000:00:14.2: irq 10, io mem 0xdffffe00
Nov 11 10:09:47 uncle_bilbo ehci_hcd 0000:00:14.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004
Nov 11 10:09:47 uncle_bilbo usb usb2: configuration #1 chosen from 1 choice
Nov 11 10:09:47 uncle_bilbo hub 2-0:1.0: USB hub found
Nov 11 10:09:47 uncle_bilbo hub 2-0:1.0: 4 ports detected
Nov 11 10:09:47 uncle_bilbo ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
Nov 11 10:09:47 uncle_bilbo 3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
Nov 11 10:09:47 uncle_bilbo 0000:00:0a.0: 3Com PCI 3c980C Python-T at e0856f80.
Nov 11 10:09:47 uncle_bilbo ACPI: PCI Interrupt 0000:00:11.3[D] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
Nov 11 10:09:47 uncle_bilbo uhci_hcd 0000:00:11.3: UHCI Host Controller
Nov 11 10:09:47 uncle_bilbo uhci_hcd 0000:00:11.3: new USB bus registered, assigned bus number 3
Nov 11 10:09:47 uncle_bilbo uhci_hcd 0000:00:11.3: irq 10, io base 0x0000d400
Nov 11 10:09:47 uncle_bilbo usb usb3: configuration #1 chosen from 1 choice
Nov 11 10:09:47 uncle_bilbo hub 3-0:1.0: USB hub found
Nov 11 10:09:47 uncle_bilbo hub 3-0:1.0: 2 ports detected
Nov 11 10:09:47 uncle_bilbo gameport: NS558 PnP Gameport is pnp00:05/gameport0, io 0x201, speed 877kHz
Nov 11 10:09:47 uncle_bilbo usb 1-1: new full speed USB device using uhci_hcd and address 2
Nov 11 10:09:47 uncle_bilbo ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
Nov 11 10:09:47 uncle_bilbo ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
Nov 11 10:09:47 uncle_bilbo uhci_hcd 0000:00:14.0: UHCI Host Controller
Nov 11 10:09:47 uncle_bilbo uhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4
Nov 11 10:09:47 uncle_bilbo uhci_hcd 0000:00:14.0: irq 11, io base 0x0000cc00
Nov 11 10:09:47 uncle_bilbo usb usb4: configuration #1 chosen from 1 choice
Nov 11 10:09:47 uncle_bilbo hub 4-0:1.0: USB hub found
Nov 11 10:09:47 uncle_bilbo hub 4-0:1.0: 2 ports detected
Nov 11 10:09:47 uncle_bilbo usb 1-1: not running at top speed; connect to a high speed hub
Nov 11 10:09:47 uncle_bilbo usb 1-1: configuration #1 chosen from 1 choice
Nov 11 10:09:47 uncle_bilbo ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
Nov 11 10:09:47 uncle_bilbo Linux agpgart interface v0.101 (c) Dave Jones
Nov 11 10:09:47 uncle_bilbo Installing spdif_bug patch: Audigy 1 ES [SB0160]
Nov 11 10:09:47 uncle_bilbo ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
Nov 11 10:09:47 uncle_bilbo ACPI: PCI Interrupt 0000:00:14.1[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
Nov 11 10:09:47 uncle_bilbo uhci_hcd 0000:00:14.1: UHCI Host Controller
Nov 11 10:09:47 uncle_bilbo uhci_hcd 0000:00:14.1: new USB bus registered, assigned bus number 5
Nov 11 10:09:47 uncle_bilbo uhci_hcd 0000:00:14.1: irq 10, io base 0x0000c800
Nov 11 10:09:47 uncle_bilbo usb usb5: configuration #1 chosen from 1 choice
Nov 11 10:09:47 uncle_bilbo hub 5-0:1.0: USB hub found
Nov 11 10:09:47 uncle_bilbo hub 5-0:1.0: 2 ports detected
Nov 11 10:09:47 uncle_bilbo agpgart: Detected VIA KT266/KY266x/KT333 chipset
Nov 11 10:09:47 uncle_bilbo agpgart: AGP aperture is 128M @ 0xe0000000
Nov 11 10:09:47 uncle_bilbo gameport: EMU10K1 is pci0000:00:0c.1/gameport0, io 0xdc00, speed 1242kHz
Nov 11 10:09:47 uncle_bilbo lp0: using parport0 (interrupt-driven).
Nov 11 10:09:47 uncle_bilbo input: PS2++ Logitech MX Mouse as /class/input/input1
Nov 11 10:09:47 uncle_bilbo ppdev: user-space parallel port driver
Nov 11 10:09:47 uncle_bilbo input: PC Speaker as /class/input/input2
Nov 11 10:09:47 uncle_bilbo SCSI subsystem initialized
Nov 11 10:09:47 uncle_bilbo Initializing USB Mass Storage driver...
Nov 11 10:09:47 uncle_bilbo scsi0 : SCSI emulation for USB Mass Storage devices
Nov 11 10:09:47 uncle_bilbo usbcore: registered new driver usb-storage
Nov 11 10:09:47 uncle_bilbo USB Mass Storage support registered.
Nov 11 10:09:47 uncle_bilbo Real Time Clock Driver v1.12ac
Nov 11 10:09:47 uncle_bilbo Vendor: Generic Model: CF Rev: 1.6E
Nov 11 10:09:47 uncle_bilbo Type: Direct-Access ANSI SCSI revision: 00
Nov 11 10:09:47 uncle_bilbo EXT3 FS on hda4, internal journal
Nov 11 10:09:47 uncle_bilbo ReiserFS: hdb1: found reiserfs format "3.6" with standard journal
Nov 11 10:09:47 uncle_bilbo ReiserFS: hdb1: using ordered data mode
Nov 11 10:09:47 uncle_bilbo ReiserFS: hdb1: journal params: device hdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
Nov 11 10:09:47 uncle_bilbo ReiserFS: hdb1: checking transaction log (hdb1)
Nov 11 10:09:47 uncle_bilbo ReiserFS: hdb1: Using r5 hash to sort names
Nov 11 10:09:47 uncle_bilbo SGI XFS with ACLs, security attributes, large block numbers, no debug enabled
Nov 11 10:09:47 uncle_bilbo SGI XFS Quota Management subsystem
Nov 11 10:09:47 uncle_bilbo XFS mounting filesystem hdc1
Nov 11 10:09:47 uncle_bilbo Adding 683920k swap on /dev/hda2. Priority:-1 extents:1 across:683920k
Nov 11 10:09:47 uncle_bilbo eth0: setting full-duplex.
Nov 11 10:10:52 uncle_bilbo NET: Registered protocol family 10
Nov 11 10:10:52 uncle_bilbo lo: Disabled Privacy Extensions
Nov 11 10:10:52 uncle_bilbo IPv6 over IPv4 tunneling driver
Nov 11 10:10:53 uncle_bilbo nvidia: module license 'NVIDIA' taints kernel.
Nov 11 10:10:53 uncle_bilbo ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
Nov 11 10:10:53 uncle_bilbo NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-7184 Tue Aug 1 18:38:58 PDT 2006
Nov 11 10:10:54 uncle_bilbo agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
Nov 11 10:10:54 uncle_bilbo agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
Nov 11 10:10:54 uncle_bilbo agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
Nov 11 10:11:02 uncle_bilbo agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
Nov 11 10:11:02 uncle_bilbo agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
Nov 11 10:11:02 uncle_bilbo agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x modeOffline
Pages: 1