[SOLVED] Input issues on resume after hibernation

Soyman · 2021-10-31 15:03:40

I use my desktop computer all day every day and put it into hibernation every night so I don't have to set up my i3 workspaces and open all my programs every day.
some months ago I first encountered a bug where no HID device did anything. Plugging in a new keyboard/mouse did nothing either.
I don't think that the system was frozen. I tried hibernating with btop in the foreground and it showed firefox saturating one core upon resume.
I always have 10-20 firefox windows open and each can have 1-20 tabs. This issue only happened after around ~30% of resumes from hibernation.

Recently, after an update IIRC, the issue went away completely. However firefox had some rendering issues after resume. This was a known bug of firefox.

A few days ago, I ran another update and the rendering issues were resolved but now the input issues have occurred on every resume.
I tried hibernating with firefox closed and an instance of chromium and nyxt running.
The same issue occurred and chromium saturated 2 cores for about 30 seconds before settling down.
The input was unresponsive until I rebooted the computer.

I have found people with similar issues on the internet but most of them are laptop users.
Some have resolved their issues by adding

atkbd.reset

to

GRUB_CMDLINE_LINUX_DEFAULT

but that doesn't seem to resolve my issue.
I am suspending to a swapfile using

resume_offset

.

I've been using arch on/off for around 5 years and as a daily driver on desktop and laptop for half a year so I know my way around.
I'm however not sure how to debug this.
Any help is greatly appreciated.

Last edited by Soyman (2023-02-16 23:48:35)

seth · 2021-11-01 15:58:30

All HID usb wired?
Post the complete system journal of a boot/hibernate/resume cycle - a hard reboot w/ the powerbutton will most likely spoil the disk sync of the journal, so schedule a reboot in eg. the systemd sleep hook to run like 5 minutes after resuming from the hibernation (otherwise a clean reboot w/o any input is gonna be hard…)

Edit: bonus points if you try to re/attach (usb input) devices between resume and reboot.

Last edited by seth (2021-11-01 16:02:00)

Soyman · 2021-11-21 13:16:41

I resolved my issue, thanks for pushing me on the right track.
I had tried reconnecting many usb devices after resuming from hibernation but it didn't work.

journalctl didn't seem to have any information. I don't think I could even see that point where the computer hibernated there.
I'm using https://xon.sh/
dmesg was a better candidate so I used sched to pipe dmesg to a file after hibernating and resuming since I couldn't use the keyboard to do it.

"dmesg --time-format iso" showed this upon hibernating

...
2021-11-21T00:54:29,524827+00:00 usb usb3: root hub lost power or was reset
2021-11-21T00:54:29,524832+00:00 usb usb2: root hub lost power or was reset
2021-11-21T00:54:29,524834+00:00 usb usb4: root hub lost power or was reset
2021-11-21T00:54:29,524847+00:00 usb usb1: root hub lost power or was reset
...

and this when resuming

...
2021-11-21T00:54:39,983553+00:00 xhci_hcd 0000:00:14.0: Abort failed to stop command ring: -110
2021-11-21T00:54:39,983561+00:00 xhci_hcd 0000:00:14.0: xHCI host controller not responding, assume dead
2021-11-21T00:54:39,983569+00:00 xhci_hcd 0000:00:14.0: HC died; cleaning up
2021-11-21T00:54:39,983599+00:00 xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
2021-11-21T00:54:40,396879+00:00 usb 4-5: device not accepting address 2, error -22
2021-11-21T00:54:40,398154+00:00 PM: hibernation: Basic memory bitmaps freed
2021-11-21T00:54:40,398159+00:00 OOM killer enabled.
2021-11-21T00:54:40,398159+00:00 Restarting tasks ... 
2021-11-21T00:54:40,398208+00:00 usb 4-5: USB disconnect, device number 2
2021-11-21T00:54:40,398261+00:00 usb 3-4: USB disconnect, device number 2
2021-11-21T00:54:40,399502+00:00 done.
2021-11-21T00:54:40,399916+00:00 PM: hibernation: hibernation exit
2021-11-21T00:54:40,409487+00:00 usb 4-6: USB disconnect, device number 3
2021-11-21T00:54:40,409492+00:00 usb 4-6.4: USB disconnect, device number 4
2021-11-21T00:54:40,415031+00:00 audit: type=1130 audit(1637456080.290:153): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-hibernate comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
2021-11-21T00:54:40,415036+00:00 audit: type=1131 audit(1637456080.290:154): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-hibernate comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
2021-11-21T00:54:40,570327+00:00 usb 3-9: USB disconnect, device number 3
2021-11-21T00:54:40,570331+00:00 usb 3-9.2: USB disconnect, device number 5
2021-11-21T00:54:40,570633+00:00 usb 3-10: USB disconnect, device number 4
2021-11-21T00:54:40,570635+00:00 usb 3-10.1: USB disconnect, device number 7
2021-11-21T00:54:41,127318+00:00 usb 3-10.3: USB disconnect, device number 8
2021-11-21T00:54:41,127325+00:00 usb 3-10.3.1: USB disconnect, device number 10
2021-11-21T00:54:41,127917+00:00 usb 3-10.4: USB disconnect, device number 9
2021-11-21T00:54:41,128363+00:00 usb 3-14: USB disconnect, device number 6
...

This problem is discussed in another thread and this solution worked for me.

I also used sched to try this command after hibernation and it worked! Great relief.
So I made a root-resume hook as described in the wiki which runs this script:

$cat reset_usb.sh

#!/bin/sh

echo "0000:00:14.0" > /sys/bus/pci/drivers/xhci_hcd/unbind
sleep 3
echo "0000:00:14.0" > /sys/bus/pci/drivers/xhci_hcd/bind

I don't know how stable these ids are but it hasn't failed yet.

Slithery · 2021-11-21 13:57:52

Soyman wrote:

I use my desktop computer all day every day and put it into hibernation every night so I don't have to set up my i3 workspaces and open all my programs every day

I know this is irrelevant to the thread but you do know that you can configure i3 to automatically setup your workspaces and open your applications?

Soyman · 2021-11-21 15:10:47

Slithery wrote:

Soyman wrote:
I use my desktop computer all day every day and put it into hibernation every night so I don't have to set up my i3 workspaces and open all my programs every day
I know this is irrelevant to the thread but you do know that you can configure i3 to automatically setup your workspaces and open your applications?

I have tried two or three times to set it up to do so and I haven't managed to make it do what I want.
Hibernation does everything I want besides letting me upgrade but I'm fine with doing that just once in a while.
If you know how to make i3-resurrect or something else work as well as hibernation then please tell me how.
I want to restore all my firefox windows with all their tabs, all my emacs windows, all the various jetbrains IDEs and their windows. When I tried this last I mostly remember a bunch of placeholders that weren't correctly populated.

Soyman · 2023-02-16 23:49:27

The issue went away eventually. I had some issues with black screens on resume from suspending but they too were eventually fixed through a nvidia driver update. It was on a 1080 GPU. Marking it as solved.

Arch Linux

#1 2021-10-31 15:03:40

[SOLVED] Input issues on resume after hibernation

#2 2021-11-01 15:58:30

Re: [SOLVED] Input issues on resume after hibernation

#3 2021-11-21 13:16:41

Re: [SOLVED] Input issues on resume after hibernation

#4 2021-11-21 13:57:52

Re: [SOLVED] Input issues on resume after hibernation

#5 2021-11-21 15:10:47

Re: [SOLVED] Input issues on resume after hibernation

#6 2023-02-16 23:49:27

Re: [SOLVED] Input issues on resume after hibernation

Board footer