You are not logged in.

Pages: 1

#1 2022-08-29 19:43:37

am.nj
Member
Registered: 2022-08-29
Posts: 7

[Solved] Can't detect discrete card with xrandr --listproviders

Hi
I have an HP ProBook 4530s laptop with two graphics cards.
I want to enable Radeon HD6490M as my primary card and always use it.
xrandr --listproviders command just shows intel one so I can't go further with Prime wiki!
It's a fresh install of arch, kde and sddm.
I read about graphic cards and prime in wiki and search forum, but I have no idea what's wrong!
Please help.

glxinfo|egrep "OpenGL vendor|OpenGL renderer"
OpenGL vendor string: Intel
OpenGL renderer string: Mesa Intel(R) HD Graphics 3000 (SNB GT2)
$ xrandr --listproviders
Providers: number : 1
Provider 0: id: 0x44 cap: 0xf, Source Output, Sink Output, Source Offload, Sink Offload crtcs: 2 outputs: 4 associated providers: 0 name:modesetting
$ lspci | grep VGA
00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09)
01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Seymour [Radeon HD 6400M/7400M Series]
$ lspci -v (just VGAs)
00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) (prog-if 00 [VGA controller])
        DeviceName: 32
        Subsystem: Hewlett-Packard Company Device 167d
        Flags: bus master, fast devsel, latency 0, IRQ 40
        Memory at d4000000 (64-bit, non-prefetchable) [size=4M]
        Memory at c0000000 (64-bit, prefetchable) [size=256M]
        I/O ports at 6000 [size=64]
        Expansion ROM at 000c0000 [virtual] [disabled] [size=128K]
        Capabilities: <access denied>
        Kernel driver in use: i915
        Kernel modules: i915

01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Seymour [Radeon HD 6400M/7400M Series] (prog-if 00 [VGA controller])
        Subsystem: Hewlett-Packard Company Radeon HD 6490M
        Flags: bus master, fast devsel, latency 0, IRQ 39
        Memory at b0000000 (64-bit, prefetchable) [size=256M]
        Memory at d4a00000 (64-bit, non-prefetchable) [size=128K]
        I/O ports at 5000 [size=256]
        Expansion ROM at d4a20000 [disabled] [size=128K]
        Capabilities: <access denied>
        Kernel driver in use: radeon
        Kernel modules: radeon, amdgpu
$ pacman -Qs xf86-video
local/xf86-video-ati 1:19.1.0.r9.g5eba006e-2 (xorg-drivers)
    X.org ati video driver
$ ls /etc/X11/
xinit  xorg.conf.d
$ ls /etc/X11/xorg.conf.d/
empty!
$ cat /var/log/Xorg.0.log
[     6.544] (--) Log file renamed from "/var/log/Xorg.pid-376.log" to "/var/log/Xorg.0.log"
[     6.546] 
X.Org X Server 1.21.1.4
X Protocol Version 11, Revision 0
[     6.546] Current Operating System: Linux enzo 5.19.4-arch1-1 #1 SMP PREEMPT_DYNAMIC Thu, 25 Aug 2022 17:31:12 +0000 x86_64
[     6.546] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=727203a6-82f0-48ce-abb6-6e6dedf9a9d5 rw loglevel=3 quiet
[     6.546]  
[     6.546] Current version of pixman: 0.40.0
[     6.546]    Before reporting problems, check http://wiki.x.org
        to make sure that you have the latest version.
[     6.546] Markers: (--) probed, (**) from config file, (==) default setting,
        (++) from command line, (!!) notice, (II) informational,
        (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[     6.546] (==) Log file: "/var/log/Xorg.0.log", Time: Mon Aug 29 23:37:10 2022
[     6.548] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[     6.549] (==) No Layout section.  Using the first Screen section.
[     6.549] (==) No screen section available. Using defaults.
[     6.549] (**) |-->Screen "Default Screen Section" (0)
[     6.549] (**) |   |-->Monitor "<default monitor>"
[     6.550] (==) No monitor specified for screen "Default Screen Section".
        Using a default monitor configuration.
[     6.550] (==) Automatically adding devices
[     6.550] (==) Automatically enabling devices
[     6.550] (==) Automatically adding GPU devices
[     6.550] (==) Automatically binding GPU devices
[     6.550] (==) Max clients allowed: 256, resource mask: 0x1fffff
[     6.551] (WW) The directory "/usr/share/fonts/misc" does not exist.
[     6.551]    Entry deleted from font path.
[     6.552] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/TTF".
[     6.552]    Entry deleted from font path.
[     6.552]    (Run 'mkfontdir' on "/usr/share/fonts/TTF").
[     6.552] (WW) The directory "/usr/share/fonts/OTF" does not exist.
[     6.552]    Entry deleted from font path.
[     6.552] (WW) The directory "/usr/share/fonts/Type1" does not exist.
[     6.552]    Entry deleted from font path.
[     6.552] (WW) The directory "/usr/share/fonts/100dpi" does not exist.
[     6.552]    Entry deleted from font path.
[     6.552] (WW) The directory "/usr/share/fonts/75dpi" does not exist.
[     6.552]    Entry deleted from font path.
[     6.552] (==) FontPath set to:

[     6.552] (==) ModulePath set to "/usr/lib/xorg/modules"
[     6.552] (II) The server relies on udev to provide the list of input devices.
        If no devices become available, reconfigure udev or disable AutoAddDevices.
[     6.552] (II) Module ABI versions:
[     6.552]    X.Org ANSI C Emulation: 0.4
[     6.552]    X.Org Video Driver: 25.2
[     6.552]    X.Org XInput driver : 24.4
[     6.552]    X.Org Server Extension : 10.0
[     6.552] (++) using VT number 1

[     6.552] (II) systemd-logind: logind integration requires -keeptty and -keeptty was not provided, disabling logind integration
[     6.554] (II) xfree86: Adding drm device (/dev/dri/card0)
[     6.554] (II) Platform probe for /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.0/drm/card0
[     6.555] (II) xfree86: Adding drm device (/dev/dri/card1)
[     6.555] (II) Platform probe for /sys/devices/pci0000:00/0000:00:02.0/drm/card1
[     6.574] (--) PCI:*(0@0:2:0) 8086:0116:103c:167d rev 9, Mem @ 0xd4000000/4194304, 0xc0000000/268435456, I/O @ 0x00006000/64, BIOS @ 0x????????/131072
[     6.574] (--) PCI: (1@0:0:0) 1002:6760:103c:167d rev 0, Mem @ 0xb0000000/268435456, 0xd4a00000/131072, I/O @ 0x00005000/256, BIOS @ 0x????????/131072
[     6.574] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[     6.574] (II) LoadModule: "glx"
[     6.575] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[     6.586] (II) Module glx: vendor="X.Org Foundation"
[     6.586]    compiled for 1.21.1.4, module version = 1.0.0
[     6.586]    ABI class: X.Org Server Extension, version 10.0
[     6.586] (II) Applying OutputClass "Radeon" to /dev/dri/card0
[     6.586]    loading driver: radeon
[     6.586] (==) Matched intel as autoconfigured driver 0
[     6.586] (==) Matched radeon as autoconfigured driver 1
[     6.586] (==) Matched ati as autoconfigured driver 2
[     6.586] (==) Matched modesetting as autoconfigured driver 3
[     6.586] (==) Matched fbdev as autoconfigured driver 4
[     6.586] (==) Matched vesa as autoconfigured driver 5
[     6.586] (==) Assigned the driver to the xf86ConfigLayout
[     6.586] (II) LoadModule: "intel"
[     6.587] (WW) Warning, couldn't open module intel
[     6.587] (EE) Failed to load module "intel" (module does not exist, 0)
[     6.587] (II) LoadModule: "radeon"
[     6.587] (II) Loading /usr/lib/xorg/modules/drivers/radeon_drv.so
[     6.592] (II) Module radeon: vendor="X.Org Foundation"
[     6.592]    compiled for 1.21.1.1, module version = 19.1.0
[     6.592]    Module class: X.Org Video Driver
[     6.592]    ABI class: X.Org Video Driver, version 25.2
[     6.592] (II) LoadModule: "ati"
[     6.592] (II) Loading /usr/lib/xorg/modules/drivers/ati_drv.so
[     6.593] (II) Module ati: vendor="X.Org Foundation"
[     6.593]    compiled for 1.21.1.1, module version = 19.1.0
[     6.593]    Module class: X.Org Video Driver
[     6.593]    ABI class: X.Org Video Driver, version 25.2
[     6.593] (II) LoadModule: "modesetting"
[     6.593] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so
[     6.594] (II) Module modesetting: vendor="X.Org Foundation"
[     6.594]    compiled for 1.21.1.4, module version = 1.21.1
[     6.594]    Module class: X.Org Video Driver
[     6.594]    ABI class: X.Org Video Driver, version 25.2
[     6.594] (II) LoadModule: "fbdev"
[     6.594] (WW) Warning, couldn't open module fbdev
[     6.594] (EE) Failed to load module "fbdev" (module does not exist, 0)
[     6.594] (II) LoadModule: "vesa"
[     6.594] (WW) Warning, couldn't open module vesa
[     6.594] (EE) Failed to load module "vesa" (module does not exist, 0)
[     6.594] (II) RADEON: Driver for ATI/AMD Radeon chipsets:
        ATI Radeon Mobility X600 (M24), ATI FireMV 2400,
        ATI Radeon Mobility X300 (M24), ATI FireGL M24 GL,
        ATI Radeon X600 (RV380), ATI FireGL V3200 (RV380),
        ATI Radeon IGP320 (A3), ATI Radeon IGP330/340/350 (A4),
        ATI Radeon 9500, ATI Radeon 9600TX, ATI FireGL Z1, ATI Radeon 9800SE,
        ATI Radeon 9800, ATI FireGL X2, ATI Radeon 9600, ATI Radeon 9600SE,
        ATI Radeon 9600XT, ATI FireGL T2, ATI Radeon 9650, ATI FireGL RV360,
        ATI Radeon 7000 IGP (A4+), ATI Radeon 8500 AIW,
        ATI Radeon IGP320M (U1), ATI Radeon IGP330M/340M/350M (U2),
        ATI Radeon Mobility 7000 IGP, ATI Radeon 9000/PRO, ATI Radeon 9000,
        ATI Radeon X800 (R420), ATI Radeon X800PRO (R420),
        ATI Radeon X800SE (R420), ATI FireGL X3 (R420),
        ATI Radeon Mobility 9800 (M18), ATI Radeon X800 SE (R420),
        ATI Radeon X800XT (R420), ATI Radeon X800 VE (R420),
        ATI Radeon X850 (R480), ATI Radeon X850 XT (R480),
        ATI Radeon X850 SE (R480), ATI Radeon X850 PRO (R480),
        ATI Radeon X850 XT PE (R480), ATI Radeon Mobility M7,
        ATI Mobility FireGL 7800 M7, ATI Radeon Mobility M6,
        ATI FireGL Mobility 9000 (M9), ATI Radeon Mobility 9000 (M9),
        ATI Radeon 9700 Pro, ATI Radeon 9700/9500Pro, ATI FireGL X1,
        ATI Radeon 9800PRO, ATI Radeon 9800XT,
        ATI Radeon Mobility 9600/9700 (M10/M11),
        ATI Radeon Mobility 9600 (M10), ATI Radeon Mobility 9600 (M11),
        ATI FireGL Mobility T2 (M10), ATI FireGL Mobility T2e (M11),
        ATI Radeon, ATI FireGL 8700/8800, ATI Radeon 8500, ATI Radeon 9100,
        ATI Radeon 7500, ATI Radeon VE/7000, ATI ES1000,
        ATI Radeon Mobility X300 (M22), ATI Radeon Mobility X600 SE (M24C),
        ATI FireGL M22 GL, ATI Radeon X800 (R423), ATI Radeon X800PRO (R423),
        ATI Radeon X800LE (R423), ATI Radeon X800SE (R423),
        ATI Radeon X800 XTP (R430), ATI Radeon X800 XL (R430),
        ATI Radeon X800 SE (R430), ATI Radeon X800 (R430),
        ATI FireGL V7100 (R423), ATI FireGL V5100 (R423),
        ATI FireGL unknown (R423), ATI Mobility FireGL V5000 (M26),
        ATI Mobility Radeon X700 XL (M26), ATI Mobility Radeon X700 (M26),
        ATI Radeon X550XTX, ATI Radeon 9100 IGP (A5),
        ATI Radeon Mobility 9100 IGP (U3), ATI Radeon XPRESS 200,
        ATI Radeon XPRESS 200M, ATI Radeon 9250, ATI Radeon 9200,
        ATI Radeon 9200SE, ATI FireMV 2200, ATI Radeon X300 (RV370),
        ATI Radeon X600 (RV370), ATI Radeon X550 (RV370),
        ATI FireGL V3100 (RV370), ATI FireMV 2200 PCIE (RV370),
        ATI Radeon Mobility 9200 (M9+), ATI Mobility Radeon X800 XT (M28),
        ATI Mobility FireGL V5100 (M28), ATI Mobility Radeon X800 (M28),
        ATI Radeon X850, ATI unknown Radeon / FireGL (R480),
        ATI Radeon X800XT (R423), ATI FireGL V5000 (RV410),
        ATI Radeon X700 XT (RV410), ATI Radeon X700 PRO (RV410),
        ATI Radeon X700 SE (RV410), ATI Radeon X700 (RV410),
        ATI Radeon X1800, ATI Mobility Radeon X1800 XT,
        ATI Mobility Radeon X1800, ATI Mobility FireGL V7200,
        ATI FireGL V7200, ATI FireGL V5300, ATI Mobility FireGL V7100,
        ATI FireGL V7300, ATI FireGL V7350, ATI Radeon X1600, ATI RV505,
        ATI Radeon X1300/X1550, ATI Radeon X1550, ATI M54-GL,
        ATI Mobility Radeon X1400, ATI Radeon X1550 64-bit,
        ATI Mobility Radeon X1300, ATI Radeon X1300, ATI FireGL V3300,
        ATI FireGL V3350, ATI Mobility Radeon X1450,
        ATI Mobility Radeon X2300, ATI Mobility Radeon X1350,
        ATI FireMV 2250, ATI Radeon X1650, ATI Mobility FireGL V5200,
        ATI Mobility Radeon X1600, ATI Radeon X1300 XT/X1600 Pro,
        ATI FireGL V3400, ATI Mobility FireGL V5250,
        ATI Mobility Radeon X1700, ATI Mobility Radeon X1700 XT,
        ATI FireGL V5200, ATI Radeon X2300HD, ATI Mobility Radeon HD 2300,
        ATI Radeon X1950, ATI Radeon X1900, ATI AMD Stream Processor,
        ATI RV560, ATI Mobility Radeon X1900, ATI Radeon X1950 GT, ATI RV570,
        ATI FireGL V7400, ATI Radeon 9100 PRO IGP,
        ATI Radeon Mobility 9200 IGP, ATI Radeon X1200, ATI RS740,
        ATI RS740M, ATI Radeon HD 2900 XT, ATI Radeon HD 2900 Pro,
        ATI Radeon HD 2900 GT, ATI FireGL V8650, ATI FireGL V8600,
        ATI FireGL V7600, ATI Radeon 4800 Series, ATI Radeon HD 4870 x2,
        ATI Radeon HD 4850 x2, ATI FirePro V8750 (FireGL),
        ATI FirePro V7760 (FireGL), ATI Mobility RADEON HD 4850,
        ATI Mobility RADEON HD 4850 X2, ATI FirePro RV770,
        AMD FireStream 9270, AMD FireStream 9250, ATI FirePro V8700 (FireGL),
        ATI Mobility RADEON HD 4870, ATI Mobility RADEON M98,
        ATI FirePro M7750, ATI M98, ATI Mobility Radeon HD 4650,
        ATI Radeon RV730 (AGP), ATI Mobility Radeon HD 4670,
        ATI FirePro M5750, ATI RV730XT [Radeon HD 4670], ATI RADEON E4600,
        ATI Radeon HD 4600 Series, ATI RV730 PRO [Radeon HD 4650],
        ATI FirePro V7750 (FireGL), ATI FirePro V5700 (FireGL),
        ATI FirePro V3750 (FireGL), ATI Mobility Radeon HD 4830,
        ATI Mobility Radeon HD 4850, ATI FirePro M7740, ATI RV740,
        ATI Radeon HD 4770, ATI Radeon HD 4700 Series, ATI RV610,
        ATI Radeon HD 2400 XT, ATI Radeon HD 2400 Pro,
        ATI Radeon HD 2400 PRO AGP, ATI FireGL V4000, ATI Radeon HD 2350,
        ATI Mobility Radeon HD 2400 XT, ATI Mobility Radeon HD 2400,
        ATI RADEON E2400, ATI FireMV 2260, ATI RV670, ATI Radeon HD3870,
        ATI Mobility Radeon HD 3850, ATI Radeon HD3850,
        ATI Mobility Radeon HD 3850 X2, ATI Mobility Radeon HD 3870,
        ATI Mobility Radeon HD 3870 X2, ATI Radeon HD3870 X2,
        ATI FireGL V7700, ATI Radeon HD3690, AMD Firestream 9170,
        ATI Radeon HD 4550, ATI Radeon RV710, ATI Radeon HD 4350,
        ATI Mobility Radeon 4300 Series, ATI Mobility Radeon 4500 Series,
        ATI FirePro RG220, ATI Mobility Radeon 4330, ATI RV630,
        ATI Mobility Radeon HD 2600, ATI Mobility Radeon HD 2600 XT,
        ATI Radeon HD 2600 XT AGP, ATI Radeon HD 2600 Pro AGP,
        ATI Radeon HD 2600 XT, ATI Radeon HD 2600 Pro, ATI Gemini RV630,
        ATI Gemini Mobility Radeon HD 2600 XT, ATI FireGL V5600,
        ATI FireGL V3600, ATI Radeon HD 2600 LE,
        ATI Mobility FireGL Graphics Processor, ATI Radeon HD 3470,
        ATI Mobility Radeon HD 3430, ATI Mobility Radeon HD 3400 Series,
        ATI Radeon HD 3450, ATI Radeon HD 3430, ATI FirePro V3700,
        ATI FireMV 2450, ATI Radeon HD 3600 Series, ATI Radeon HD 3650 AGP,
        ATI Radeon HD 3600 PRO, ATI Radeon HD 3600 XT,
        ATI Mobility Radeon HD 3650, ATI Mobility Radeon HD 3670,
        ATI Mobility FireGL V5700, ATI Mobility FireGL V5725,
        ATI Radeon HD 3200 Graphics, ATI Radeon 3100 Graphics,
        ATI Radeon HD 3300 Graphics, ATI Radeon 3000 Graphics, SUMO, SUMO2,
        ATI Radeon HD 4200, ATI Radeon 4100, ATI Mobility Radeon HD 4200,
        ATI Mobility Radeon 4100, ATI Radeon HD 4290, ATI Radeon HD 4250,
        AMD Radeon HD 6310 Graphics, AMD Radeon HD 6250 Graphics,
        AMD Radeon HD 6300 Series Graphics,
        AMD Radeon HD 6200 Series Graphics, PALM, CYPRESS,
        ATI FirePro (FireGL) Graphics Adapter, AMD Firestream 9370,
        AMD Firestream 9350, ATI Radeon HD 5800 Series,
        ATI Radeon HD 5900 Series, ATI Mobility Radeon HD 5800 Series,
        ATI Radeon HD 5700 Series, ATI Radeon HD 6700 Series,
        ATI Mobility Radeon HD 5000 Series, ATI Mobility Radeon HD 5570,
        ATI Radeon HD 5670, ATI Radeon HD 5570, ATI Radeon HD 5500 Series,
        REDWOOD, ATI Mobility Radeon Graphics, CEDAR, ATI FirePro 2270,
        ATI Radeon HD 5450, CAYMAN, AMD Radeon HD 6900 Series,
        AMD Radeon HD 6900M Series, Mobility Radeon HD 6000 Series, BARTS,
        AMD Radeon HD 6800 Series, AMD Radeon HD 6700 Series, TURKS, CAICOS,
        ARUBA, TAHITI, PITCAIRN, VERDE, OLAND, HAINAN, BONAIRE, KABINI,
        MULLINS, KAVERI, HAWAII
[     6.598] (II) modesetting: Driver for Modesetting Kernel Drivers: kms
[     6.602] (II) modeset(0): using drv /dev/dri/card1
[     6.602] (II) [KMS] Kernel modesetting enabled.
[     6.602] (II) modeset(0): Creating default Display subsection in Screen section
        "Default Screen Section" for depth/fbbpp 24/32
[     6.602] (==) modeset(0): Depth 24, (==) framebuffer bpp 32
[     6.602] (==) modeset(0): RGB weight 888
[     6.602] (==) modeset(0): Default visual is TrueColor
[     6.602] (II) Loading sub module "glamoregl"
[     6.602] (II) LoadModule: "glamoregl"
[     6.602] (II) Loading /usr/lib/xorg/modules/libglamoregl.so
[     6.609] (II) Module glamoregl: vendor="X.Org Foundation"
[     6.609]    compiled for 1.21.1.4, module version = 1.0.1
[     6.609]    ABI class: X.Org ANSI C Emulation, version 0.4
[     6.809] (II) modeset(0): glamor X acceleration enabled on Mesa Intel(R) HD Graphics 3000 (SNB GT2)
[     6.809] (II) modeset(0): glamor initialized
[     6.809] (==) modeset(0): VariableRefresh: disabled
[     6.809] (==) modeset(0): AsyncFlipSecondaries: disabled
[     6.809] (II) modeset(0): Output LVDS-1 has no monitor section
[     6.810] (II) modeset(0): Output VGA-1 has no monitor section
[     6.812] (II) modeset(0): Output HDMI-1 has no monitor section
[     6.812] (II) modeset(0): Output DP-1 has no monitor section
[     6.812] (II) modeset(0): EDID for output LVDS-1
[     6.812] (II) modeset(0): Manufacturer: LGD  Model: 2f1  Serial#: 0
[     6.812] (II) modeset(0): Year: 2010  Week: 0
[     6.812] (II) modeset(0): EDID Version: 1.3
[     6.812] (II) modeset(0): Digital Display Input
[     6.812] (II) modeset(0): Max Image Size [cm]: horiz.: 34  vert.: 19
[     6.812] (II) modeset(0): Gamma: 2.20
[     6.812] (II) modeset(0): No DPMS capabilities specified
[     6.812] (II) modeset(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 
[     6.812] (II) modeset(0): First detailed timing is preferred mode
[     6.812] (II) modeset(0): redX: 0.605 redY: 0.355   greenX: 0.329 greenY: 0.579
[     6.812] (II) modeset(0): blueX: 0.150 blueY: 0.055   whiteX: 0.313 whiteY: 0.329
[     6.812] (II) modeset(0): Manufacturer's mask: 0
[     6.812] (II) modeset(0): Supported detailed timing:
[     6.812] (II) modeset(0): clock: 69.3 MHz   Image Size:  344 x 194 mm
[     6.812] (II) modeset(0): h_active: 1366  h_sync: 1402  h_sync_end 1442 h_blank_end 1480 h_border: 0
[     6.812] (II) modeset(0): v_active: 768  v_sync: 771  v_sync_end 776 v_blanking: 780 v_border: 0
[     6.812] (II) modeset(0):  LG Display
[     6.812] (II) modeset(0):  LP156WH4-TLD1
[     6.812] (II) modeset(0): EDID (in hex):
[     6.812] (II) modeset(0):   00ffffffffffff0030e4f10200000000
[     6.812] (II) modeset(0):   00140103802213780a05859b5b549426
[     6.812] (II) modeset(0):   0e505400000001010101010101010101
[     6.812] (II) modeset(0):   010101010101121b567250000c302428
[     6.812] (II) modeset(0):   350058c2100000190000000000000000
[     6.812] (II) modeset(0):   00000000000000000000000000fe004c
[     6.812] (II) modeset(0):   4720446973706c61790a2020000000fe
[     6.812] (II) modeset(0):   004c503135365748342d544c443100ff
[     6.813] (II) modeset(0): Printing probed modes for output LVDS-1
[     6.813] (II) modeset(0): Modeline "1366x768"x60.0   69.30  1366 1402 1442 1480  768 771 776 780 -hsync -vsync (46.8 kHz eP)
[     6.813] (II) modeset(0): Modeline "1280x720"x120.0  156.12  1280 1376 1512 1744  720 721 724 746 doublescan -hsync +vsync (89.5 kHz d)
[     6.813] (II) modeset(0): Modeline "1280x720"x120.0  120.75  1280 1304 1320 1360  720 721 724 740 doublescan +hsync -vsync (88.8 kHz d)
[     6.813] (II) modeset(0): Modeline "1280x720"x59.9   74.50  1280 1344 1472 1664  720 723 728 748 -hsync +vsync (44.8 kHz d)
[     6.813] (II) modeset(0): Modeline "1280x720"x59.7   63.75  1280 1328 1360 1440  720 723 728 741 +hsync -vsync (44.3 kHz d)
[     6.813] (II) modeset(0): Modeline "1024x768"x120.1  133.47  1024 1100 1212 1400  768 768 770 794 doublescan -hsync +vsync (95.3 kHz d)
[     6.813] (II) modeset(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz d)
[     6.813] (II) modeset(0): Modeline "960x720"x120.0  117.00  960 1024 1128 1300  720 720 722 750 doublescan -hsync +vsync (90.0 kHz d)
[     6.813] (II) modeset(0): Modeline "928x696"x120.1  109.15  928 976 1088 1264  696 696 698 719 doublescan -hsync +vsync (86.4 kHz d)
[     6.813] (II) modeset(0): Modeline "896x672"x120.0  102.40  896 960 1060 1224  672 672 674 697 doublescan -hsync +vsync (83.7 kHz d)
[     6.813] (II) modeset(0): Modeline "1024x576"x119.9   98.50  1024 1092 1200 1376  576 577 580 597 doublescan -hsync +vsync (71.6 kHz d)
[     6.813] (II) modeset(0): Modeline "1024x576"x119.9   78.38  1024 1048 1064 1104  576 577 580 592 doublescan +hsync -vsync (71.0 kHz d)
[     6.813] (II) modeset(0): Modeline "1024x576"x59.9   46.50  1024 1064 1160 1296  576 579 584 599 -hsync +vsync (35.9 kHz d)
[     6.813] (II) modeset(0): Modeline "1024x576"x59.8   42.00  1024 1072 1104 1184  576 579 584 593 +hsync -vsync (35.5 kHz d)
[     6.813] (II) modeset(0): Modeline "960x600"x119.9   96.62  960 1028 1128 1296  600 601 604 622 doublescan -hsync +vsync (74.6 kHz d)
[     6.813] (II) modeset(0): Modeline "960x600"x120.0   77.00  960 984 1000 1040  600 601 604 617 doublescan +hsync -vsync (74.0 kHz d)
[     6.813] (II) modeset(0): Modeline "960x540"x119.9   86.50  960 1024 1124 1288  540 541 544 560 doublescan -hsync +vsync (67.2 kHz d)
[     6.813] (II) modeset(0): Modeline "960x540"x120.0   69.25  960 984 1000 1040  540 541 544 555 doublescan +hsync -vsync (66.6 kHz d)
[     6.813] (II) modeset(0): Modeline "960x540"x59.6   40.75  960 992 1088 1216  540 543 548 562 -hsync +vsync (33.5 kHz d)
[     6.813] (II) modeset(0): Modeline "960x540"x59.8   37.25  960 1008 1040 1120  540 543 548 556 +hsync -vsync (33.3 kHz d)
[     6.813] (II) modeset(0): Modeline "800x600"x120.0   81.00  800 832 928 1080  600 600 602 625 doublescan +hsync +vsync (75.0 kHz d)
[     6.813] (II) modeset(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz d)
[     6.813] (II) modeset(0): Modeline "800x600"x56.2   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz d)
[     6.813] (II) modeset(0): Modeline "840x525"x120.0   73.12  840 892 980 1120  525 526 529 544 doublescan -hsync +vsync (65.3 kHz d)
[     6.813] (II) modeset(0): Modeline "840x525"x119.8   59.50  840 864 880 920  525 526 529 540 doublescan +hsync -vsync (64.7 kHz d)
[     6.813] (II) modeset(0): Modeline "864x486"x59.9   32.50  864 888 968 1072  486 489 494 506 -hsync +vsync (30.3 kHz d)
[     6.813] (II) modeset(0): Modeline "864x486"x59.6   30.50  864 912 944 1024  486 489 494 500 +hsync -vsync (29.8 kHz d)
[     6.813] (II) modeset(0): Modeline "700x525"x120.0   61.00  700 744 820 940  525 526 532 541 doublescan +hsync +vsync (64.9 kHz d)
[     6.813] (II) modeset(0): Modeline "800x450"x119.9   59.12  800 848 928 1056  450 451 454 467 doublescan -hsync +vsync (56.0 kHz d)
[     6.813] (II) modeset(0): Modeline "800x450"x119.6   48.75  800 824 840 880  450 451 454 463 doublescan +hsync -vsync (55.4 kHz d)
[     6.813] (II) modeset(0): Modeline "640x512"x120.0   54.00  640 664 720 844  512 512 514 533 doublescan +hsync +vsync (64.0 kHz d)
[     6.813] (II) modeset(0): Modeline "700x450"x119.9   51.75  700 740 812 924  450 451 456 467 doublescan -hsync +vsync (56.0 kHz d)
[     6.813] (II) modeset(0): Modeline "700x450"x119.8   43.25  700 724 740 780  450 451 456 463 doublescan +hsync -vsync (55.4 kHz d)
[     6.813] (II) modeset(0): Modeline "640x480"x120.0   54.00  640 688 744 900  480 480 482 500 doublescan +hsync +vsync (60.0 kHz d)
[     6.813] (II) modeset(0): Modeline "640x480"x59.9   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz d)
[     6.813] (II) modeset(0): Modeline "720x405"x59.5   22.50  720 744 808 896  405 408 413 422 -hsync +vsync (25.1 kHz d)
[     6.813] (II) modeset(0): Modeline "720x405"x59.0   21.75  720 768 800 880  405 408 413 419 +hsync -vsync (24.7 kHz d)
[     6.813] (II) modeset(0): Modeline "684x384"x119.8   42.62  684 720 788 892  384 385 390 399 doublescan -hsync +vsync (47.8 kHz d)
[     6.813] (II) modeset(0): Modeline "684x384"x119.7   36.12  684 708 724 764  384 385 390 395 doublescan +hsync -vsync (47.3 kHz d)
[     6.813] (II) modeset(0): Modeline "640x400"x119.8   41.75  640 676 740 840  400 401 404 415 doublescan -hsync +vsync (49.7 kHz d)
[     6.813] (II) modeset(0): Modeline "640x400"x120.0   35.50  640 664 680 720  400 401 404 411 doublescan +hsync -vsync (49.3 kHz d)
[     6.813] (II) modeset(0): Modeline "640x360"x119.7   37.25  640 672 736 832  360 361 364 374 doublescan -hsync +vsync (44.8 kHz d)
[     6.813] (II) modeset(0): Modeline "640x360"x119.7   31.88  640 664 680 720  360 361 364 370 doublescan +hsync -vsync (44.3 kHz d)
[     6.813] (II) modeset(0): Modeline "640x360"x59.8   18.00  640 664 720 800  360 363 368 376 -hsync +vsync (22.5 kHz d)
[     6.813] (II) modeset(0): Modeline "640x360"x59.3   17.75  640 688 720 800  360 363 368 374 +hsync -vsync (22.2 kHz d)
[     6.813] (II) modeset(0): Modeline "512x384"x120.0   32.50  512 524 592 672  384 385 388 403 doublescan -hsync -vsync (48.4 kHz d)
[     6.813] (II) modeset(0): Modeline "512x288"x120.0   23.25  512 532 580 648  288 289 292 299 doublescan -hsync +vsync (35.9 kHz d)
[     6.813] (II) modeset(0): Modeline "512x288"x119.8   21.00  512 536 552 592  288 289 292 296 doublescan +hsync -vsync (35.5 kHz d)
[     6.813] (II) modeset(0): Modeline "480x270"x119.3   20.38  480 496 544 608  270 271 274 281 doublescan -hsync +vsync (33.5 kHz d)
[     6.813] (II) modeset(0): Modeline "480x270"x119.6   18.62  480 504 520 560  270 271 274 278 doublescan +hsync -vsync (33.3 kHz d)
[     6.813] (II) modeset(0): Modeline "400x300"x120.6   20.00  400 420 484 528  300 300 302 314 doublescan +hsync +vsync (37.9 kHz d)
[     6.813] (II) modeset(0): Modeline "400x300"x112.7   18.00  400 412 448 512  300 300 301 312 doublescan +hsync +vsync (35.2 kHz d)
[     6.813] (II) modeset(0): Modeline "432x243"x119.8   16.25  432 444 484 536  243 244 247 253 doublescan -hsync +vsync (30.3 kHz d)
[     6.813] (II) modeset(0): Modeline "432x243"x119.1   15.25  432 456 472 512  243 244 247 250 doublescan +hsync -vsync (29.8 kHz d)
[     6.813] (II) modeset(0): Modeline "320x240"x120.1   12.59  320 328 376 400  240 245 246 262 doublescan -hsync -vsync (31.5 kHz d)
[     6.813] (II) modeset(0): Modeline "360x202"x119.0   11.25  360 372 404 448  202 204 206 211 doublescan -hsync +vsync (25.1 kHz d)
[     6.813] (II) modeset(0): Modeline "360x202"x118.3   10.88  360 384 400 440  202 204 206 209 doublescan +hsync -vsync (24.7 kHz d)
[     6.813] (II) modeset(0): Modeline "320x180"x119.7    9.00  320 332 360 400  180 181 184 188 doublescan -hsync +vsync (22.5 kHz d)
[     6.813] (II) modeset(0): Modeline "320x180"x118.6    8.88  320 344 360 400  180 181 184 187 doublescan +hsync -vsync (22.2 kHz d)
[     6.814] (II) modeset(0): EDID for output VGA-1
[     6.816] (II) modeset(0): EDID for output HDMI-1
[     6.816] (II) modeset(0): EDID for output DP-1
[     6.816] (II) modeset(0): Output LVDS-1 connected
[     6.816] (II) modeset(0): Output VGA-1 disconnected
[     6.816] (II) modeset(0): Output HDMI-1 disconnected
[     6.816] (II) modeset(0): Output DP-1 disconnected
[     6.816] (II) modeset(0): Using exact sizes for initial modes
[     6.816] (II) modeset(0): Output LVDS-1 using initial mode 1366x768 +0+0
[     6.816] (==) modeset(0): Using gamma correction (1.0, 1.0, 1.0)
[     6.816] (==) modeset(0): DPI set to (96, 96)
[     6.816] (II) Loading sub module "fb"
[     6.816] (II) LoadModule: "fb"
[     6.816] (II) Module "fb" already built-in
[     6.816] (==) RADEON(G0): Depth 24, (--) framebuffer bpp 32
[     6.816] (II) RADEON(G0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
[     6.816] (==) RADEON(G0): Default visual is TrueColor
[     6.816] (==) RADEON(G0): RGB weight 888
[     6.816] (II) RADEON(G0): Using 8 bits per RGB (8 bit DAC)
[     6.816] (--) RADEON(G0): Chipset: "CAICOS" (ChipID = 0x6760)
[     6.816] (II) Loading sub module "fb"
[     6.816] (II) LoadModule: "fb"
[     6.816] (II) Module "fb" already built-in
[     6.816] (II) Loading sub module "dri2"
[     6.816] (II) LoadModule: "dri2"
[     6.816] (II) Module "dri2" already built-in
[     6.826] (II) Loading sub module "glamoregl"
[     6.826] (II) LoadModule: "glamoregl"
[     6.826] (II) Loading /usr/lib/xorg/modules/libglamoregl.so
[     6.826] (II) Module glamoregl: vendor="X.Org Foundation"
[     6.826]    compiled for 1.21.1.4, module version = 1.0.1
[     6.826]    ABI class: X.Org ANSI C Emulation, version 0.4
[     6.833] (II) RADEON(G0): glamor X acceleration enabled on AMD CAICOS (DRM 2.50.0 / 5.19.4-arch1-1, LLVM 14.0.6)
[     6.833] (II) RADEON(G0): glamor detected, initialising EGL layer.
[     6.833] (II) RADEON(G0): KMS Color Tiling: enabled
[     6.833] (II) RADEON(G0): KMS Color Tiling 2D: enabled
[     6.833] (==) RADEON(G0): TearFree property default: auto
[     6.897] (II) RADEON(G0): Output VGA-1-1 has no monitor section
[     6.963] (II) RADEON(G0): EDID for output VGA-1-1
[     6.963] (II) RADEON(G0): mem size init: gart size :3fdde000 vram size: s:40000000 visible:fc9d000
[     6.963] (==) RADEON(G0): DPI set to (96, 96)
[     6.963] (==) RADEON(G0): Using gamma correction (1.0, 1.0, 1.0)
[     6.963] (II) Loading sub module "ramdac"
[     6.963] (II) LoadModule: "ramdac"
[     6.963] (II) Module "ramdac" already built-in
[     6.997] (==) modeset(0): Backing store enabled
[     6.997] (==) modeset(0): Silken mouse enabled
[     7.019] (II) modeset(0): Initializing kms color map for depth 24, 8 bpc.
[     7.020] (==) modeset(0): DPMS enabled
[     7.020] (II) modeset(0): [DRI2] Setup complete
[     7.020] (II) modeset(0): [DRI2]   DRI driver: crocus
[     7.020] (II) modeset(0): [DRI2]   VDPAU driver: va_gl
[     7.020] (II) RADEON(G0): [DRI2] Setup complete
[     7.020] (II) RADEON(G0): [DRI2]   DRI driver: r600
[     7.020] (II) RADEON(G0): [DRI2]   VDPAU driver: r600
[     7.020] (II) RADEON(G0): Front buffer size: 3072K
[     7.020] (II) RADEON(G0): VRAM usage limit set to 229986K
[     7.020] (==) RADEON(G0): Backing store enabled
[     7.020] (II) RADEON(G0): Direct rendering enabled
[     7.038] (II) RADEON(G0): Use GLAMOR acceleration.
[     7.038] (II) RADEON(G0): Acceleration enabled
[     7.038] (==) RADEON(G0): DPMS enabled
[     7.038] (==) RADEON(G0): Silken mouse enabled
[     7.038] (II) Initializing extension Generic Event Extension
[     7.038] (II) Initializing extension SHAPE
[     7.038] (II) Initializing extension MIT-SHM
[     7.038] (II) Initializing extension XInputExtension
[     7.039] (II) Initializing extension XTEST
[     7.039] (II) Initializing extension BIG-REQUESTS
[     7.039] (II) Initializing extension SYNC
[     7.039] (II) Initializing extension XKEYBOARD
[     7.039] (II) Initializing extension XC-MISC
[     7.039] (II) Initializing extension SECURITY
[     7.039] (II) Initializing extension XFIXES
[     7.039] (II) Initializing extension RENDER
[     7.039] (II) Initializing extension RANDR
[     7.040] (II) Initializing extension COMPOSITE
[     7.040] (II) Initializing extension DAMAGE
[     7.040] (II) Initializing extension MIT-SCREEN-SAVER
[     7.040] (II) Initializing extension DOUBLE-BUFFER
[     7.040] (II) Initializing extension RECORD
[     7.040] (II) Initializing extension DPMS
[     7.040] (II) Initializing extension Present
[     7.040] (II) Initializing extension DRI3
[     7.040] (II) Initializing extension X-Resource
[     7.041] (II) Initializing extension XVideo
[     7.041] (II) Initializing extension XVideo-MotionCompensation
[     7.041] (II) Initializing extension GLX
[     7.046] (II) AIGLX: Loaded and initialized crocus
[     7.046] (II) GLX: Initialized DRI2 GL provider for screen 0
[     7.046] (II) Initializing extension XFree86-VidModeExtension
[     7.046] (II) Initializing extension XFree86-DGA
[     7.046] (II) Initializing extension XFree86-DRI
[     7.046] (II) Initializing extension DRI2
[     7.051] (II) modeset(0): Damage tracking initialized
[     7.051] (II) modeset(0): Setting screen physical size to 361 x 203
[     7.114] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[     7.114] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[     7.114] (II) LoadModule: "libinput"
[     7.114] (II) Loading /usr/lib/xorg/modules/input/libinput_drv.so
[     7.118] (II) Module libinput: vendor="X.Org Foundation"
[     7.118]    compiled for 1.21.1.3, module version = 1.2.1
[     7.118]    Module class: X.Org XInput Driver
[     7.118]    ABI class: X.Org XInput driver, version 24.4
[     7.118] (II) Using input driver 'libinput' for 'Power Button'
[     7.118] (**) Power Button: always reports core events
[     7.118] (**) Option "Device" "/dev/input/event2"
[     7.126] (II) event2  - Power Button: is tagged by udev as: Keyboard
[     7.126] (II) event2  - Power Button: device is a keyboard
[     7.126] (II) event2  - Power Button: device removed
[     7.150] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2/event2"
[     7.150] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[     7.151] (II) event2  - Power Button: is tagged by udev as: Keyboard
[     7.151] (II) event2  - Power Button: device is a keyboard
[     7.151] (II) config/udev: Adding input device Video Bus (/dev/input/event15)
[     7.151] (**) Video Bus: Applying InputClass "libinput keyboard catchall"
[     7.151] (II) Using input driver 'libinput' for 'Video Bus'
[     7.151] (**) Video Bus: always reports core events
[     7.151] (**) Option "Device" "/dev/input/event15"
[     7.152] (II) event15 - Video Bus: is tagged by udev as: Keyboard
[     7.152] (II) event15 - Video Bus: device is a keyboard
[     7.153] (II) event15 - Video Bus: device removed
[     7.183] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:01/input/input22/event15"
[     7.183] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[     7.184] (II) event15 - Video Bus: is tagged by udev as: Keyboard
[     7.184] (II) event15 - Video Bus: device is a keyboard
[     7.185] (II) config/udev: Adding input device Video Bus (/dev/input/event14)
[     7.185] (**) Video Bus: Applying InputClass "libinput keyboard catchall"
[     7.185] (II) Using input driver 'libinput' for 'Video Bus'
[     7.185] (**) Video Bus: always reports core events
[     7.185] (**) Option "Device" "/dev/input/event14"
[     7.186] (II) event14 - Video Bus: is tagged by udev as: Keyboard
[     7.186] (II) event14 - Video Bus: device is a keyboard
[     7.186] (II) event14 - Video Bus: device removed
[     7.226] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:00/LNXVIDEO:00/input/input21/event14"
[     7.226] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 8)
[     7.227] (II) event14 - Video Bus: is tagged by udev as: Keyboard
[     7.228] (II) event14 - Video Bus: device is a keyboard
[     7.228] (II) config/udev: Adding input device Lid Switch (/dev/input/event1)
[     7.228] (II) No input driver specified, ignoring this device.
[     7.228] (II) This device may have been added with another device file.
[     7.229] (II) config/udev: Adding input device Sleep Button (/dev/input/event0)
[     7.229] (**) Sleep Button: Applying InputClass "libinput keyboard catchall"
[     7.229] (II) Using input driver 'libinput' for 'Sleep Button'
[     7.229] (**) Sleep Button: always reports core events
[     7.229] (**) Option "Device" "/dev/input/event0"
[     7.230] (II) event0  - Sleep Button: is tagged by udev as: Keyboard
[     7.230] (II) event0  - Sleep Button: device is a keyboard
[     7.230] (II) event0  - Sleep Button: device removed
[     7.256] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0/event0"
[     7.256] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 9)
[     7.257] (II) event0  - Sleep Button: is tagged by udev as: Keyboard
[     7.257] (II) event0  - Sleep Button: device is a keyboard
[     7.259] (II) config/udev: Adding input device MOSART Semi. 2.4G Keyboard Mouse (/dev/input/event3)
[     7.259] (**) MOSART Semi. 2.4G Keyboard Mouse: Applying InputClass "libinput keyboard catchall"
[     7.259] (II) Using input driver 'libinput' for 'MOSART Semi. 2.4G Keyboard Mouse'
[     7.259] (**) MOSART Semi. 2.4G Keyboard Mouse: always reports core events
[     7.259] (**) Option "Device" "/dev/input/event3"
[     7.260] (II) event3  - MOSART Semi. 2.4G Keyboard Mouse: is tagged by udev as: Keyboard
[     7.261] (II) event3  - MOSART Semi. 2.4G Keyboard Mouse: device is a keyboard
[     7.261] (II) event3  - MOSART Semi. 2.4G Keyboard Mouse: device removed
[     7.366] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.0/0003:062A:4182.0001/input/input3/event3"
[     7.366] (II) XINPUT: Adding extended input device "MOSART Semi. 2.4G Keyboard Mouse" (type: KEYBOARD, id 10)
[     7.368] (II) event3  - MOSART Semi. 2.4G Keyboard Mouse: is tagged by udev as: Keyboard
[     7.368] (II) event3  - MOSART Semi. 2.4G Keyboard Mouse: device is a keyboard
[     7.369] (II) config/udev: Adding input device MOSART Semi. 2.4G Keyboard Mouse (/dev/input/event4)
[     7.369] (**) MOSART Semi. 2.4G Keyboard Mouse: Applying InputClass "libinput pointer catchall"
[     7.369] (II) Using input driver 'libinput' for 'MOSART Semi. 2.4G Keyboard Mouse'
[     7.369] (**) MOSART Semi. 2.4G Keyboard Mouse: always reports core events
[     7.369] (**) Option "Device" "/dev/input/event4"
[     7.371] (II) event4  - MOSART Semi. 2.4G Keyboard Mouse: is tagged by udev as: Mouse
[     7.371] (II) event4  - MOSART Semi. 2.4G Keyboard Mouse: device is a pointer
[     7.371] (II) event4  - MOSART Semi. 2.4G Keyboard Mouse: device removed
[     7.650] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.1/0003:062A:4182.0002/input/input4/event4"
[     7.650] (II) XINPUT: Adding extended input device "MOSART Semi. 2.4G Keyboard Mouse" (type: MOUSE, id 11)
[     7.650] (**) Option "AccelerationScheme" "none"
[     7.650] (**) MOSART Semi. 2.4G Keyboard Mouse: (accel) selected scheme none/0
[     7.650] (**) MOSART Semi. 2.4G Keyboard Mouse: (accel) acceleration factor: 2.000
[     7.650] (**) MOSART Semi. 2.4G Keyboard Mouse: (accel) acceleration threshold: 4
[     7.651] (II) event4  - MOSART Semi. 2.4G Keyboard Mouse: is tagged by udev as: Mouse
[     7.652] (II) event4  - MOSART Semi. 2.4G Keyboard Mouse: device is a pointer
[     7.652] (II) config/udev: Adding input device MOSART Semi. 2.4G Keyboard Mouse (/dev/input/mouse0)
[     7.652] (II) No input driver specified, ignoring this device.
[     7.652] (II) This device may have been added with another device file.
[     7.653] (II) config/udev: Adding input device MOSART Semi. 2.4G Keyboard Mouse Consumer Control (/dev/input/event5)
[     7.653] (**) MOSART Semi. 2.4G Keyboard Mouse Consumer Control: Applying InputClass "libinput keyboard catchall"
[     7.653] (II) Using input driver 'libinput' for 'MOSART Semi. 2.4G Keyboard Mouse Consumer Control'
[     7.653] (**) MOSART Semi. 2.4G Keyboard Mouse Consumer Control: always reports core events
[     7.653] (**) Option "Device" "/dev/input/event5"
[     7.655] (II) event5  - MOSART Semi. 2.4G Keyboard Mouse Consumer Control: is tagged by udev as: Keyboard
[     7.655] (II) event5  - MOSART Semi. 2.4G Keyboard Mouse Consumer Control: device is a keyboard
[     7.655] (II) event5  - MOSART Semi. 2.4G Keyboard Mouse Consumer Control: device removed
[     7.826] (II) libinput: MOSART Semi. 2.4G Keyboard Mouse Consumer Control: needs a virtual subdevice
[     7.826] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.1/0003:062A:4182.0002/input/input5/event5"
[     7.826] (II) XINPUT: Adding extended input device "MOSART Semi. 2.4G Keyboard Mouse Consumer Control" (type: MOUSE, id 12)
[     7.826] (**) Option "AccelerationScheme" "none"
[     7.826] (**) MOSART Semi. 2.4G Keyboard Mouse Consumer Control: (accel) selected scheme none/0
[     7.826] (**) MOSART Semi. 2.4G Keyboard Mouse Consumer Control: (accel) acceleration factor: 2.000
[     7.826] (**) MOSART Semi. 2.4G Keyboard Mouse Consumer Control: (accel) acceleration threshold: 4
[     7.828] (II) event5  - MOSART Semi. 2.4G Keyboard Mouse Consumer Control: is tagged by udev as: Keyboard
[     7.828] (II) event5  - MOSART Semi. 2.4G Keyboard Mouse Consumer Control: device is a keyboard
[     7.829] (II) config/udev: Adding input device MOSART Semi. 2.4G Keyboard Mouse System Control (/dev/input/event7)
[     7.829] (**) MOSART Semi. 2.4G Keyboard Mouse System Control: Applying InputClass "libinput keyboard catchall"
[     7.829] (II) Using input driver 'libinput' for 'MOSART Semi. 2.4G Keyboard Mouse System Control'
[     7.829] (**) MOSART Semi. 2.4G Keyboard Mouse System Control: always reports core events
[     7.829] (**) Option "Device" "/dev/input/event7"
[     7.831] (II) event7  - MOSART Semi. 2.4G Keyboard Mouse System Control: is tagged by udev as: Keyboard
[     7.831] (II) event7  - MOSART Semi. 2.4G Keyboard Mouse System Control: device is a keyboard
[     7.831] (II) event7  - MOSART Semi. 2.4G Keyboard Mouse System Control: device removed
[     7.873] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.1/0003:062A:4182.0002/input/input6/event7"
[     7.873] (II) XINPUT: Adding extended input device "MOSART Semi. 2.4G Keyboard Mouse System Control" (type: KEYBOARD, id 13)
[     7.875] (II) event7  - MOSART Semi. 2.4G Keyboard Mouse System Control: is tagged by udev as: Keyboard
[     7.875] (II) event7  - MOSART Semi. 2.4G Keyboard Mouse System Control: device is a keyboard
[     7.876] (II) config/udev: Adding input device MOSART Semi. 2.4G Keyboard Mouse (/dev/input/event8)
[     7.876] (II) No input driver specified, ignoring this device.
[     7.876] (II) This device may have been added with another device file.
[     7.876] (II) config/udev: Adding input device HDA Intel PCH Mic (/dev/input/event16)
[     7.876] (II) No input driver specified, ignoring this device.
[     7.876] (II) This device may have been added with another device file.
[     7.877] (II) config/udev: Adding input device HDA Intel PCH Front Headphone (/dev/input/event17)
[     7.877] (II) No input driver specified, ignoring this device.
[     7.877] (II) This device may have been added with another device file.
[     7.877] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event18)
[     7.877] (II) No input driver specified, ignoring this device.
[     7.877] (II) This device may have been added with another device file.
[     7.878] (II) config/udev: Adding input device HP HD Webcam [Fixed]: HP HD Web (/dev/input/event13)
[     7.878] (**) HP HD Webcam [Fixed]: HP HD Web: Applying InputClass "libinput keyboard catchall"
[     7.878] (II) Using input driver 'libinput' for 'HP HD Webcam [Fixed]: HP HD Web'
[     7.878] (**) HP HD Webcam [Fixed]: HP HD Web: always reports core events
[     7.878] (**) Option "Device" "/dev/input/event13"
[     7.879] (II) event13 - HP HD Webcam [Fixed]: HP HD Web: is tagged by udev as: Keyboard
[     7.879] (II) event13 - HP HD Webcam [Fixed]: HP HD Web: device is a keyboard
[     7.879] (II) event13 - HP HD Webcam [Fixed]: HP HD Web: device removed
[     8.170] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.4/2-1.4:1.0/input/input20/event13"
[     8.170] (II) XINPUT: Adding extended input device "HP HD Webcam [Fixed]: HP HD Web" (type: KEYBOARD, id 14)
[     8.171] (II) event13 - HP HD Webcam [Fixed]: HP HD Web: is tagged by udev as: Keyboard
[     8.171] (II) event13 - HP HD Webcam [Fixed]: HP HD Web: device is a keyboard
[     8.172] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event6)
[     8.172] (**) AT Translated Set 2 keyboard: Applying InputClass "libinput keyboard catchall"
[     8.172] (II) Using input driver 'libinput' for 'AT Translated Set 2 keyboard'
[     8.172] (**) AT Translated Set 2 keyboard: always reports core events
[     8.172] (**) Option "Device" "/dev/input/event6"
[     8.173] (II) event6  - AT Translated Set 2 keyboard: is tagged by udev as: Keyboard
[     8.173] (II) event6  - AT Translated Set 2 keyboard: device is a keyboard
[     8.174] (II) event6  - AT Translated Set 2 keyboard: device removed
[     8.383] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input8/event6"
[     8.383] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 15)
[     8.384] (II) event6  - AT Translated Set 2 keyboard: is tagged by udev as: Keyboard
[     8.384] (II) event6  - AT Translated Set 2 keyboard: device is a keyboard
[     8.386] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/event12)
[     8.386] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "libinput touchpad catchall"
[     8.386] (II) Using input driver 'libinput' for 'SynPS/2 Synaptics TouchPad'
[     8.386] (**) SynPS/2 Synaptics TouchPad: always reports core events
[     8.386] (**) Option "Device" "/dev/input/event12"
[     8.387] (II) event12 - SynPS/2 Synaptics TouchPad: is tagged by udev as: Touchpad
[     8.389] (II) event12 - SynPS/2 Synaptics TouchPad: device is a touchpad
[     8.389] (II) event12 - SynPS/2 Synaptics TouchPad: device removed
[     8.433] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio4/input/input18/event12"
[     8.433] (II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD, id 16)
[     8.434] (**) Option "AccelerationScheme" "none"
[     8.434] (**) SynPS/2 Synaptics TouchPad: (accel) selected scheme none/0
[     8.434] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration factor: 2.000
[     8.434] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration threshold: 4
[     8.435] (II) event12 - SynPS/2 Synaptics TouchPad: is tagged by udev as: Touchpad
[     8.436] (II) event12 - SynPS/2 Synaptics TouchPad: device is a touchpad
[     8.437] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/mouse1)
[     8.437] (II) No input driver specified, ignoring this device.
[     8.437] (II) This device may have been added with another device file.
[     8.437] (II) config/udev: Adding input device ST LIS3LV02DL Accelerometer (/dev/input/event9)
[     8.437] (II) No input driver specified, ignoring this device.
[     8.437] (II) This device may have been added with another device file.
[     8.438] (II) config/udev: Adding input device ST LIS3LV02DL Accelerometer (/dev/input/js0)
[     8.438] (II) No input driver specified, ignoring this device.
[     8.438] (II) This device may have been added with another device file.
[     8.438] (II) config/udev: Adding input device PC Speaker (/dev/input/event10)
[     8.438] (II) No input driver specified, ignoring this device.
[     8.438] (II) This device may have been added with another device file.
[     8.441] (II) config/udev: Adding input device HP WMI hotkeys (/dev/input/event11)
[     8.441] (**) HP WMI hotkeys: Applying InputClass "libinput keyboard catchall"
[     8.441] (II) Using input driver 'libinput' for 'HP WMI hotkeys'
[     8.441] (**) HP WMI hotkeys: always reports core events
[     8.441] (**) Option "Device" "/dev/input/event11"
[     8.442] (II) event11 - HP WMI hotkeys: is tagged by udev as: Keyboard Switch
[     8.442] (II) event11 - HP WMI hotkeys: device is a keyboard
[     8.442] (II) event11 - HP WMI hotkeys: device removed
[     8.460] (**) Option "config_info" "udev:/sys/devices/virtual/input/input19/event11"
[     8.460] (II) XINPUT: Adding extended input device "HP WMI hotkeys" (type: KEYBOARD, id 17)
[     8.460] (II) event11 - HP WMI hotkeys: is tagged by udev as: Keyboard Switch
[     8.461] (II) event11 - HP WMI hotkeys: device is a keyboard
[     8.472] (**) MOSART Semi. 2.4G Keyboard Mouse Consumer Control: Applying InputClass "libinput keyboard catchall"
[     8.472] (II) Using input driver 'libinput' for 'MOSART Semi. 2.4G Keyboard Mouse Consumer Control'
[     8.472] (**) MOSART Semi. 2.4G Keyboard Mouse Consumer Control: always reports core events
[     8.472] (**) Option "Device" "/dev/input/event5"
[     8.472] (II) libinput: MOSART Semi. 2.4G Keyboard Mouse Consumer Control: is a virtual subdevice
[     8.472] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.1/0003:062A:4182.0002/input/input5/event5"
[     8.472] (II) XINPUT: Adding extended input device "MOSART Semi. 2.4G Keyboard Mouse Consumer Control" (type: KEYBOARD, id 18)
[     8.523] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event18)
[     8.523] (II) No input driver specified, ignoring this device.
[     8.523] (II) This device may have been added with another device file.
[     8.524] (II) config/udev: Adding input device HDA Intel PCH Mic (/dev/input/event16)
[     8.524] (II) No input driver specified, ignoring this device.
[     8.524] (II) This device may have been added with another device file.
[     8.524] (II) config/udev: Adding input device HDA Intel PCH Front Headphone (/dev/input/event17)
[     8.524] (II) No input driver specified, ignoring this device.
[     8.524] (II) This device may have been added with another device file.
[     8.557] (II) modeset(0): EDID vendor "LGD", prod id 753
[     8.558] (II) modeset(0): Printing DDC gathered Modelines:
[     8.558] (II) modeset(0): Modeline "1366x768"x0.0   69.30  1366 1402 1442 1480  768 771 776 780 -hsync -vsync (46.8 kHz eP)
[     8.696] (II) modeset(0): EDID vendor "LGD", prod id 753
[     8.696] (II) modeset(0): Printing DDC gathered Modelines:
[     8.696] (II) modeset(0): Modeline "1366x768"x0.0   69.30  1366 1402 1442 1480  768 771 776 780 -hsync -vsync (46.8 kHz eP)
[     8.699] (II) config/udev: removing GPU device /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.0/drm/card0 /dev/dri/card0
[     8.699] xf86: remove device 0 /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.0/drm/card0
[     8.700] (II) UnloadModule: "radeon"
[     8.700] (II) UnloadSubModule: "glamoregl"
[     8.700] (II) Unloading glamoregl
[     8.700] (II) config/udev: Adding drm device (/dev/dri/card0)
[     8.700] (II) xfree86: Adding drm device (/dev/dri/card0)
[     8.700] (II) Platform probe for /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.0/drm/card0
[     8.700] (II) LoadModule: "modesetting"
[     8.700] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so
[     8.700] (II) Module modesetting: vendor="X.Org Foundation"
[     8.700]    compiled for 1.21.1.4, module version = 1.21.1
[     8.700]    Module class: X.Org Video Driver
[     8.700]    ABI class: X.Org Video Driver, version 25.2
[     8.700] (II) UnloadModule: "modesetting"
[     8.700] (II) Unloading modesetting
[     8.700] (II) Failed to load module "modesetting" (already loaded, 0)
[     8.700] xf86: found device 1
[    17.917] (II) modeset(0): EDID vendor "LGD", prod id 753
[    17.917] (II) modeset(0): Printing DDC gathered Modelines:
[    17.917] (II) modeset(0): Modeline "1366x768"x0.0   69.30  1366 1402 1442 1480  768 771 776 780 -hsync -vsync (46.8 kHz eP)
[    18.537] (II) modeset(0): EDID vendor "LGD", prod id 753
[    18.537] (II) modeset(0): Printing DDC gathered Modelines:
[    18.537] (II) modeset(0): Modeline "1366x768"x0.0   69.30  1366 1402 1442 1480  768 771 776 780 -hsync -vsync (46.8 kHz eP)
[   960.775] (II) Axis 0 value 1247 is outside expected range [1257, 5970]
See https://wayland.freedesktop.org/libinput/doc/1.21.0/absolute_coordinate_ranges.html for details

Last edited by am.nj (2022-09-01 15:43:18)

Offline

#2 2022-08-29 20:48:57

seth
Member
From: Won't reply 2 private help req
Registered: 2012-09-03
Posts: 75,805

Re: [Solved] Can't detect discrete card with xrandr --listproviders

[     6.554] (II) xfree86: Adding drm device (/dev/dri/card0)
[     6.554] (II) Platform probe for /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.0/drm/card0
[     6.586] (II) Applying OutputClass "Radeon" to /dev/dri/card0
[     8.699] (II) config/udev: removing GPU device /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.0/drm/card0 /dev/dri/card0
[     8.699] xf86: remove device 0 /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.0/drm/card0
[     8.700] (II) config/udev: Adding drm device (/dev/dri/card0)
[     8.700] (II) xfree86: Adding drm device (/dev/dri/card0)
[     8.700] (II) Platform probe for /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.0/drm/card0

Check dmesg/the system journal.
Possibly https://wiki.archlinux.org/title/PRIME# … pplication

I want to enable Radeon HD6490M as my primary card and always use it.

Does the BIOS provide an option to disable the IGP?
(Cause that will spare you the framebuffer copy)

How to upload text · How to boot w/o GUI · Disable Windows Fast-Start! · Fix your xinitrc

Offline

#3 2022-08-30 10:33:30

am.nj
Member
Registered: 2022-08-29
Posts: 7

Re: [Solved] Can't detect discrete card with xrandr --listproviders

Hi seth
Thanks! You saved me days! It's now detect by xrandr!

Check dmesg/the system journal.
Possibly https://wiki.archlinux.org/title/PRIME# … pplication

Yes, that's true! Solved by adding radeon.runpm=0 to the kernel parameters in the bootloader.
Before the fix, there were many repeated red lines in dmesg:

 kernel: debugfs: File 'radeon_ring_gfx' in directory '1' already present!
 kernel: debugfs: File 'radeon_ring_dma1' in directory '1' already present!
 kernel: debugfs: File 'radeon_ring_uvd' in directory '1' already present!

I can't see them now!

Does the BIOS provide an option to disable the IGP?
(Cause that will spare you the framebuffer copy)

No, Just a Switchable Graphics checkbox, if I disable this then my discrete card won't detect by arch at all.

I want to enable Radeon HD6490M as my primary card and always use it.

Is it ok to go with https://wiki.archlinux.org/title/PRIME#User_scenarios ?
Can I just turn off Intel graphic in arch?

Last edited by am.nj (2022-08-30 12:48:29)

Offline

#4 2022-08-30 13:35:49

seth
Member
From: Won't reply 2 private help req
Registered: 2012-09-03
Posts: 75,805

Re: [Solved] Can't detect discrete card with xrandr --listproviders

You'll obviously have to adapt that for your drivers and PCI IDs - you should also check --listproviders again to see whether you can actually redirect the output (but I assume so)

Can I just turn off Intel graphic in arch?

No. You'll need it as crtc to access the outputs attached to it (that's why I asked for the BIOS option)
You may alternatively try whether the IGP is good enough™ for everyday use and only kick in the GPU w/ "DRI_PRIME=1" for heavy(ier) duty stuff.

How to upload text · How to boot w/o GUI · Disable Windows Fast-Start! · Fix your xinitrc

Offline

#5 2022-08-31 09:29:40

am.nj
Member
Registered: 2022-08-29
Posts: 7

Re: [Solved] Can't detect discrete card with xrandr --listproviders

I've installed some standard KDE apps while thinking about what should I do with dual graphics based on your suggestion (DRI_PRIME) and suddenly xrandr can't detect the Radeon card again.
I didn't change a single setting either by GUI or config files.
List of installed apps:

ark kcalc kdegraphics-thumbnailers kdesdk-thumbnailers kdegraphics-thumbnailers okular spectacle kwrite kompare gwenview ffmpegthumbs plasma-systemmonitor kamoso sddm-kcm kwallet-pam kscreen   kwalletmanager kinfocenter khotkeys  kde-gtk-config breeze-gtk bluedevil

I removed kscreen and bluedevil (if they are relative to the problem!) but nothing changed.

Xorg unloading radeon module again!

$ journalctl | egrep "radeon|01:00.0|vga"
Aug 31 13:34:04 enzo kernel: Command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=727203a6-82f0-48ce-abb6-6e6dedf9a9d5 rw loglevel=3 quiet radeon.runpm=0
Aug 31 13:34:04 enzo kernel: Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=727203a6-82f0-48ce-abb6-6e6dedf9a9d5 rw loglevel=3 quiet radeon.runpm=0
Aug 31 13:34:04 enzo kernel: pci 0000:01:00.0: [1002:6760] type 00 class 0x030000
Aug 31 13:34:04 enzo kernel: pci 0000:01:00.0: reg 0x10: [mem 0xb0000000-0xbfffffff 64bit pref]
Aug 31 13:34:04 enzo kernel: pci 0000:01:00.0: reg 0x18: [mem 0xd4a00000-0xd4a1ffff 64bit]
Aug 31 13:34:04 enzo kernel: pci 0000:01:00.0: reg 0x20: [io  0x5000-0x50ff]
Aug 31 13:34:04 enzo kernel: pci 0000:01:00.0: reg 0x30: [mem 0xfffe0000-0xffffffff pref]
Aug 31 13:34:04 enzo kernel: pci 0000:01:00.0: enabling Extended Tags
Aug 31 13:34:04 enzo kernel: pci 0000:01:00.0: supports D1 D2
Aug 31 13:34:04 enzo kernel: pci 0000:00:02.0: vgaarb: setting as boot VGA device
Aug 31 13:34:04 enzo kernel: pci 0000:00:02.0: vgaarb: bridge control possible
Aug 31 13:34:04 enzo kernel: pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
Aug 31 13:34:04 enzo kernel: pci 0000:01:00.0: vgaarb: bridge control possible
Aug 31 13:34:04 enzo kernel: pci 0000:01:00.0: vgaarb: VGA device added: decodes=io+mem,owns=none,locks=none
Aug 31 13:34:04 enzo kernel: vgaarb: loaded
Aug 31 13:34:04 enzo kernel: pci 0000:01:00.0: can't claim BAR 6 [mem 0xfffe0000-0xffffffff pref]: no compatible bridge window
Aug 31 13:34:04 enzo kernel: pci 0000:01:00.0: BAR 6: assigned [mem 0xd4a20000-0xd4a3ffff pref]
Aug 31 13:34:05 enzo kernel: [drm] radeon kernel modesetting enabled.
Aug 31 13:34:05 enzo kernel: vga_switcheroo: detected switching method \_SB_.PCI0.GFX0.ATPX handle
Aug 31 13:34:05 enzo kernel: radeon 0000:01:00.0: enabling device (0000 -> 0003)
Aug 31 13:34:06 enzo kernel: radeon 0000:01:00.0: VRAM: 1024M 0x0000000000000000 - 0x000000003FFFFFFF (1024M used)
Aug 31 13:34:06 enzo kernel: radeon 0000:01:00.0: GTT: 1024M 0x0000000040000000 - 0x000000007FFFFFFF
Aug 31 13:34:06 enzo kernel: [drm] radeon: 1024M of VRAM memory ready
Aug 31 13:34:06 enzo kernel: [drm] radeon: 1024M of GTT memory ready.
Aug 31 13:34:06 enzo kernel: [drm] radeon: dpm initialized
Aug 31 13:34:06 enzo kernel: [drm] enabling PCIE gen 2 link speeds, disable with radeon.pcie_gen2=0
Aug 31 13:34:06 enzo kernel: radeon 0000:01:00.0: WB enabled
Aug 31 13:34:06 enzo kernel: radeon 0000:01:00.0: fence driver on ring 0 use gpu addr 0x0000000040000c00
Aug 31 13:34:06 enzo kernel: radeon 0000:01:00.0: fence driver on ring 3 use gpu addr 0x0000000040000c0c
Aug 31 13:34:06 enzo kernel: radeon 0000:01:00.0: fence driver on ring 5 use gpu addr 0x0000000000072118
Aug 31 13:34:06 enzo kernel: radeon 0000:01:00.0: radeon: MSI limited to 32-bit
Aug 31 13:34:06 enzo kernel: radeon 0000:01:00.0: radeon: using MSI.
Aug 31 13:34:06 enzo kernel: [drm] radeon: irq initialized.
Aug 31 13:34:06 enzo kernel: i915 0000:00:02.0: vgaarb: deactivate vga console
Aug 31 13:34:07 enzo kernel: radeon 0000:01:00.0: [drm] Cannot find any crtc or sizes
Aug 31 13:34:07 enzo kernel: [drm] Initialized radeon 2.50.0 20080528 for 0000:01:00.0 on minor 0
Aug 31 13:34:07 enzo kernel: vga_switcheroo: enabled
Aug 31 13:34:08 enzo kernel: i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=none:owns=io+mem
Aug 31 13:34:08 enzo kernel: radeon 0000:01:00.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=none:owns=none
Aug 31 13:34:08 enzo kernel: radeon 0000:01:00.0: [drm] Cannot find any crtc or sizes
Aug 31 13:34:10 enzo kernel: amdgpu: vga_switcheroo: detected switching method \_SB_.PCI0.GFX0.ATPX handle

Last edited by am.nj (2022-08-31 09:38:06)

Offline

#6 2022-08-31 14:13:54

seth
Member
From: Won't reply 2 private help req
Registered: 2012-09-03
Posts: 75,805

Re: [Solved] Can't detect discrete card with xrandr --listproviders

Why is the amdgpu module there?
Please don't grep, post the entire system journal as well as your xorg log.

How to upload text · How to boot w/o GUI · Disable Windows Fast-Start! · Fix your xinitrc

Offline

#7 2022-08-31 14:51:33

am.nj
Member
Registered: 2022-08-29
Posts: 7

Re: [Solved] Can't detect discrete card with xrandr --listproviders

Here are logs:
journalctl all
journalctl current boot (-b)
xorg log

Offline

#8 2022-08-31 15:15:59

seth
Member
From: Won't reply 2 private help req
Registered: 2012-09-03
Posts: 75,805

Re: [Solved] Can't detect discrete card with xrandr --listproviders

Aug 31 18:48:50 enzo systemd[1]: Reached target Graphical Interface.
Aug 31 18:48:51 enzo kernel: [drm] radeon kernel modesetting enabled.
Aug 31 18:48:51 enzo kernel: radeon 0000:01:00.0: enabling device (0000 -> 0003)
Aug 31 18:48:55 enzo kernel: [drm] amdgpu kernel modesetting enabled.
Aug 31 18:48:55 enzo kernel: amdgpu: vga_switcheroo: detected switching method \_SB_.PCI0.GFX0.ATPX handle
Aug 31 18:48:55 enzo kernel: ATPX version 1, functions 0x00000003
Aug 31 18:48:55 enzo kernel: amdgpu: CRAT table not found
Aug 31 18:48:55 enzo kernel: amdgpu: Virtual CRAT table created for CPU
Aug 31 18:48:55 enzo kernel: amdgpu: Topology: Add CPU node

The GPU activates extremely late and too late (after the X11 server starts) and then even more later the amdgpu module shows up for reasons.

Does the GPU show up/work when you restart the GUI (don't! reboot!)?
https://wiki.archlinux.org/title/Kernel … _KMS_start

How to upload text · How to boot w/o GUI · Disable Windows Fast-Start! · Fix your xinitrc

Offline

#9 2022-08-31 16:03:19

am.nj
Member
Registered: 2022-08-29
Posts: 7

Re: [Solved] Can't detect discrete card with xrandr --listproviders

I've tested "kquitapp5 plasmashell || killall plasmashell && kstart5 plasmashell" in this case, no it doesn't work. But the GPU shows up when logout and login again!
So I added radeon to MODULES=(radeon) in /etc/mkinitcpio.conf and then run: sudo mkinitcpio -p linux (I'm not sure if I have to run mkinitcpio -P ?)
now the GPU shows up 2 out of 10 times reboot!
I guess I need to logout and in every time.

Offline

#10 2022-08-31 16:21:53

seth
Member
From: Won't reply 2 private help req
Registered: 2012-09-03
Posts: 75,805

Re: [Solved] Can't detect discrete card with xrandr --listproviders

no it doesn't work

No, that won't work. You'll have to restart the X11 server…

But the GPU shows up when logout and login again!

…what that most likely did wink

So I added radeon to MODULES=(radeon) in /etc/mkinitcpio.conf and then run: sudo mkinitcpio -p linux (I'm not sure if I have to run mkinitcpio -P ?)

Yes. Sure the MODULES were empty before? Having i915 in there would probably also be nice.
Please post your /etc/mkinitcpio.conf and an updated system journal.

I guess I need to logout and in every time.

Yeah, no. We'll find another way tongue

How to upload text · How to boot w/o GUI · Disable Windows Fast-Start! · Fix your xinitrc

Offline

#11 2022-08-31 17:20:36

am.nj
Member
Registered: 2022-08-29
Posts: 7

Re: [Solved] Can't detect discrete card with xrandr --listproviders

No, that won't work. You'll have to restart the X11 server...

My bad!

Sure the MODULES were empty before?

Yes.

Yeah, no. We'll find another way tongue

Thank you for your time.

$ cat /etc/mkinitcpio.conf
# vim:set ft=sh
# MODULES
# The following modules are loaded before any boot hooks are
# run.  Advanced users may wish to specify all system modules
# in this array.  For instance:
#     MODULES=(piix ide_disk reiserfs)
MODULES=(i915 radeon)

# BINARIES
# This setting includes any additional binaries a given user may
# wish into the CPIO image.  This is run last, so it may be used to
# override the actual binaries included by a given hook
# BINARIES are dependency parsed, so you may safely ignore libraries
BINARIES=()

# FILES
# This setting is similar to BINARIES above, however, files are added
# as-is and are not parsed in any way.  This is useful for config files.
FILES=()

# HOOKS
# This is the most important setting in this file.  The HOOKS control the
# modules and scripts added to the image, and what happens at boot time.
# Order is important, and it is recommended that you do not change the
# order in which HOOKS are added.  Run 'mkinitcpio -H <hook name>' for
# help on a given hook.
# 'base' is _required_ unless you know precisely what you are doing.
# 'udev' is _required_ in order to automatically load modules
# 'filesystems' is _required_ unless you specify your fs modules in MODULES
# Examples:
##   This setup specifies all modules in the MODULES setting above.
##   No raid, lvm2, or encrypted root is needed.
#    HOOKS=(base)
#
##   This setup will autodetect all modules for your system and should
##   work as a sane default
#    HOOKS=(base udev autodetect block filesystems)
#
##   This setup will generate a 'full' image which supports most systems.
##   No autodetection is done.
#    HOOKS=(base udev block filesystems)
#
##   This setup assembles a pata mdadm array with an encrypted root FS.
##   Note: See 'mkinitcpio -H mdadm' for more information on raid devices.
#    HOOKS=(base udev block mdadm encrypt filesystems)
#
##   This setup loads an lvm2 volume group on a usb device.
#    HOOKS=(base udev block lvm2 filesystems)
#
##   NOTE: If you have /usr on a separate partition, you MUST include the
#    usr, fsck and shutdown hooks.
HOOKS=(base udev autodetect modconf block filesystems keyboard fsck)

# COMPRESSION
# Use this to compress the initramfs image. By default, zstd compression
# is used. Use 'cat' to create an uncompressed image.
#COMPRESSION="zstd"
#COMPRESSION="gzip"
#COMPRESSION="bzip2"
#COMPRESSION="lzma"
#COMPRESSION="xz"
#COMPRESSION="lzop"
#COMPRESSION="lz4"

# COMPRESSION_OPTIONS
# Additional options for the compressor
#COMPRESSION_OPTIONS=()

updated journalctl

Offline

#12 2022-08-31 19:53:43

seth
Member
From: Won't reply 2 private help req
Registered: 2012-09-03
Posts: 75,805

Re: [Solved] Can't detect discrete card with xrandr --listproviders

Ok, first let's just try to get amdgpu out of the way, I've not idea what or why loads it, but
https://wiki.archlinux.org/title/Kernel … acklisting - since it's probably loaded explicitly, you'll have to go w/ the "/bin/true" variant.
Though maybe it shows up in https://wiki.archlinux.org/title/Kernel_module#systemd ?

How to upload text · How to boot w/o GUI · Disable Windows Fast-Start! · Fix your xinitrc

Offline

#13 2022-09-01 15:09:46

am.nj
Member
Registered: 2022-08-29
Posts: 7

Re: [Solved] Can't detect discrete card with xrandr --listproviders

ls /etc/modules-load.d : empty.

https://wiki.archlinux.org/title/Kernel … acklisting - since it's probably loaded explicitly, you'll have to go w/ the "/bin/true" variant.

I make a file like this: /etc/modprobe.d/noamdgpu.conf and put this in it: install amdgpu /bin/true.
As modconf has already been in HOOKS array (inside /etc/mkinitcpio.conf) so It's not needed to put /etc/modprobe.d/noamdgpu.conf inside FILES array.
Then run:

mkinitcpio -P

And now the Radeon GPU shows up on my famous 10 reboot test every time! big_smile

$ xrandr --listproviders
Providers: number : 2
Provider 0: id: 0x44 cap: 0xf, Source Output, Sink Output, Source Offload, Sink Offload crtcs: 2 outputs: 4 associated providers: 1 name:modesetting
Provider 1: id: 0xb3 cap: 0xf, Source Output, Sink Output, Source Offload, Sink Offload crtcs: 4 outputs: 1 associated providers: 1 name:CAICOS @ pci:0000:01:00.0

Now radeontop shows activity with DRI_PRIME=1. I have been using Arch heavily(mostly developing Three.js stuff) without using discrete GPU for two years!
Thank you for taking the trouble to help me. I do appreciate it.

Offline

#14 2022-09-01 15:36:57

seth
Member
From: Won't reply 2 private help req
Registered: 2012-09-03
Posts: 75,805

Re: [Solved] Can't detect discrete card with xrandr --listproviders

cool
Please always remember to mark resolved threads by editing your initial posts subject - so others will know that there's no task left, but maybe a solution to find.
Thanks.

How to upload text · How to boot w/o GUI · Disable Windows Fast-Start! · Fix your xinitrc

Offline

Pages: 1

Board footer

Powered by FluxBB