You are not logged in.

Pages: 1

#1 2022-10-31 19:14:08

prayner96
Member
Registered: 2022-03-06
Posts: 72

External monitors not detected

Laptop: Ideapad Slim 7i Pro
Dual boot setup w/ Windows 11.

Note that my laptop has no issue connecting to two different monitors while booted in W11.

I have a DisplayLink deck connected to my laptop via USB-A 3.2 (Gen 1). The laptop does not connect to two of my external monitors, both using direct USB-C to USB-C, or via the DisplayLink using either USB-C to DP or USB-C to USB-C. 

$ xrandr 
Screen 0: minimum 8 x 8, current 2880 x 1800, maximum 32767 x 32767
eDP1 connected primary 2880x1800+0+0 (normal left inverted right x axis y axis) 300mm x 190mm
   2880x1800     90.01*+
   2880x1620     59.96    59.97  
   2560x1600     59.99    59.97  
   2560x1440     59.96    59.95  
   2048x1536     85.00    75.00    60.00  
   1920x1440     85.00    75.00    60.00  
   1856x1392     75.00    60.01  
   1792x1344     75.00    60.01  
   2048x1152     59.90    59.91  
   1920x1200     90.00    59.88    59.95  
   1920x1080     59.96    59.93  
   1600x1200     85.00    75.00    70.00    65.00    60.00  
   1680x1050     90.00    59.95    59.88  
   1400x1050     74.76    59.98  
   1600x900      59.95    59.82  
   1280x1024     85.02    75.02    60.02  
   1440x900      90.00  
   1400x900      90.00    59.96    59.88  
   1280x960      85.00    60.00  
   1368x768      59.88    59.85  
   1280x800      90.00    59.81    59.91  
   1152x864      75.00  
   1280x720      59.86    59.74  
   1024x768      85.00    75.03    70.07    60.00  
   1024x768i     86.96  
   1024x576      59.90    59.82  
   832x624       74.55  
   960x540       59.63    59.82  
   800x600       85.14    72.19    75.00    60.32    56.25  
   864x486       59.92    59.57  
   640x480       85.01    72.81    75.00    59.94  
   720x405       59.51    58.99  
   720x400       85.04  
   640x400       85.08  
   640x360       59.84    59.32  
   640x350       85.08  
DP1 disconnected (normal left inverted right x axis y axis)
DP2 disconnected (normal left inverted right x axis y axis)
DP3 disconnected (normal left inverted right x axis y axis)
DP4 disconnected (normal left inverted right x axis y axis)
VIRTUAL1 disconnected (normal left inverted right x axis y axis)

While plugged in, the laptop does not appear to know it is connected to the external monitor:

$ xrandr --listproviders
Providers: number : 1
Provider 0: id: 0x49 cap: 0xb, Source Output, Sink Output, Sink Offload crtcs: 5 outputs: 6 associated providers: 0 name:Intel

Offline

#2 2022-10-31 20:42:24

seth
Member
From: Don't DM me only for attention
Registered: 2012-09-03
Posts: 72,920

Re: External monitors not detected

Do you have https://aur.archlinux.org/packages/evdi/ ?
https://wiki.archlinux.org/title/DisplayLink

How to upload text · How to boot w/o GUI · Disable Windows Fast-Start! · Fix your xinitrc

Offline

#3 2022-11-01 13:39:39

prayner96
Member
Registered: 2022-03-06
Posts: 72

Re: External monitors not detected

Yep, just installed both packages, rebooted the laptop, and still no changes.

Offline

#4 2022-11-01 13:45:28

prayner96
Member
Registered: 2022-03-06
Posts: 72

Re: External monitors not detected

FYI, the laptop does not recognise an external monitor even if I directly connect a USB-C to HDMI cable to the monitor or  USB-C to USB-C cable.

Offline

#5 2022-11-01 13:55:41

seth
Member
From: Don't DM me only for attention
Registered: 2012-09-03
Posts: 72,920

Re: External monitors not detected

Please post an updated "xrandr --listproviders", your xorg log, https://wiki.archlinux.org/title/Xorg#General and a complete system journal ("sudo journalctl -b | curl -F 'file=@-' 0x0.st") and also check the reponse of plugging the external output in "dmesg -w"

How to upload text · How to boot w/o GUI · Disable Windows Fast-Start! · Fix your xinitrc

Offline

#6 2022-11-01 14:24:57

prayner96
Member
Registered: 2022-03-06
Posts: 72

Re: External monitors not detected

$ xrandr --listproviders
Providers: number : 1
Provider 0: id: 0x49 cap: 0xb, Source Output, Sink Output, Sink Offload crtcs: 5 outputs: 6 associated providers: 0 name:Intel
[    89.233] (II) event25 - ZSA Technology Labs ErgoDox EZ System Control: is tagged by udev as: Keyboard
[    89.233] (II) event25 - ZSA Technology Labs ErgoDox EZ System Control: device is a keyboard
[    89.234] (II) event25 - ZSA Technology Labs ErgoDox EZ System Control: device removed
[    89.264] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7.2/3-7.2.4/3-7.2.4:1.3/0003:3297:4974.0007/input/input34/event25"
[    89.264] (II) XINPUT: Adding extended input device "ZSA Technology Labs ErgoDox EZ System Control" (type: KEYBOARD, id 21)
[    89.266] (II) event25 - ZSA Technology Labs ErgoDox EZ System Control: is tagged by udev as: Keyboard
[    89.267] (II) event25 - ZSA Technology Labs ErgoDox EZ System Control: device is a keyboard
[    89.269] (II) config/udev: Adding input device ZSA Technology Labs ErgoDox EZ Keyboard (/dev/input/event27)
[    89.269] (**) ZSA Technology Labs ErgoDox EZ Keyboard: Applying InputClass "libinput keyboard catchall"
[    89.269] (II) Using input driver 'libinput' for 'ZSA Technology Labs ErgoDox EZ Keyboard'
[    89.269] (**) ZSA Technology Labs ErgoDox EZ Keyboard: always reports core events
[    89.269] (**) Option "Device" "/dev/input/event27"
[    89.271] (II) event27 - ZSA Technology Labs ErgoDox EZ Keyboard: is tagged by udev as: Keyboard
[    89.271] (II) event27 - ZSA Technology Labs ErgoDox EZ Keyboard: device is a keyboard
[    89.272] (II) event27 - ZSA Technology Labs ErgoDox EZ Keyboard: device removed
[    89.307] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7.2/3-7.2.4/3-7.2.4:1.3/0003:3297:4974.0007/input/input36/event27"
[    89.307] (II) XINPUT: Adding extended input device "ZSA Technology Labs ErgoDox EZ Keyboard" (type: KEYBOARD, id 22)
[    89.309] (II) event27 - ZSA Technology Labs ErgoDox EZ Keyboard: is tagged by udev as: Keyboard
[    89.310] (II) event27 - ZSA Technology Labs ErgoDox EZ Keyboard: device is a keyboard
[    89.311] (II) config/udev: Adding input device ZSA Technology Labs ErgoDox EZ (/dev/input/event24)
[    89.311] (**) ZSA Technology Labs ErgoDox EZ: Applying InputClass "libinput pointer catchall"
[    89.311] (II) Using input driver 'libinput' for 'ZSA Technology Labs ErgoDox EZ'
[    89.311] (**) ZSA Technology Labs ErgoDox EZ: always reports core events
[    89.311] (**) Option "Device" "/dev/input/event24"
[    89.369] (II) event24 - ZSA Technology Labs ErgoDox EZ: is tagged by udev as: Mouse
[    89.369] (II) event24 - ZSA Technology Labs ErgoDox EZ: device is a pointer
[    89.370] (II) event24 - ZSA Technology Labs ErgoDox EZ: device removed
[    89.400] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7.2/3-7.2.4/3-7.2.4:1.2/0003:3297:4974.0006/input/input33/event24"
[    89.401] (II) XINPUT: Adding extended input device "ZSA Technology Labs ErgoDox EZ" (type: MOUSE, id 23)
[    89.401] (**) Option "AccelerationScheme" "none"
[    89.401] (**) ZSA Technology Labs ErgoDox EZ: (accel) selected scheme none/0
[    89.401] (**) ZSA Technology Labs ErgoDox EZ: (accel) acceleration factor: 2.000
[    89.401] (**) ZSA Technology Labs ErgoDox EZ: (accel) acceleration threshold: 4
[    89.459] (II) event24 - ZSA Technology Labs ErgoDox EZ: is tagged by udev as: Mouse
[    89.459] (II) event24 - ZSA Technology Labs ErgoDox EZ: device is a pointer
[    90.005] (II) config/udev: Adding input device Integrated_Webcam_5M_IR: DELL M (/dev/input/event21)
[    90.005] (**) Integrated_Webcam_5M_IR: DELL M: Applying InputClass "libinput keyboard catchall"
[    90.005] (II) Using input driver 'libinput' for 'Integrated_Webcam_5M_IR: DELL M'
[    90.005] (**) Integrated_Webcam_5M_IR: DELL M: always reports core events
[    90.005] (**) Option "Device" "/dev/input/event21"
[    90.007] (II) event21 - Integrated_Webcam_5M_IR: DELL M: is tagged by udev as: Keyboard
[    90.007] (II) event21 - Integrated_Webcam_5M_IR: DELL M: device is a keyboard
[    90.007] (II) event21 - Integrated_Webcam_5M_IR: DELL M: device removed
[    90.044] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7.2/3-7.2.3/3-7.2.3.4/3-7.2.3.4:1.0/input/input30/event21"
[    90.044] (II) XINPUT: Adding extended input device "Integrated_Webcam_5M_IR: DELL M" (type: KEYBOARD, id 24)
[    90.075] (II) event21 - Integrated_Webcam_5M_IR: DELL M: is tagged by udev as: Keyboard
[    90.076] (II) event21 - Integrated_Webcam_5M_IR: DELL M: device is a keyboard
[    90.077] (II) config/udev: Adding input device Integrated_Webcam_5M_IR: DELL M (/dev/input/event22)
[    90.077] (**) Integrated_Webcam_5M_IR: DELL M: Applying InputClass "libinput keyboard catchall"
[    90.077] (II) Using input driver 'libinput' for 'Integrated_Webcam_5M_IR: DELL M'
[    90.077] (**) Integrated_Webcam_5M_IR: DELL M: always reports core events
[    90.077] (**) Option "Device" "/dev/input/event22"
[    90.099] (II) event22 - Integrated_Webcam_5M_IR: DELL M: is tagged by udev as: Keyboard
[    90.099] (II) event22 - Integrated_Webcam_5M_IR: DELL M: device is a keyboard
[    90.100] (II) event22 - Integrated_Webcam_5M_IR: DELL M: device removed
[    90.140] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7.2/3-7.2.3/3-7.2.3.4/3-7.2.3.4:1.2/input/input31/event22"
[    90.141] (II) XINPUT: Adding extended input device "Integrated_Webcam_5M_IR: DELL M" (type: KEYBOARD, id 25)
[    90.143] (II) event22 - Integrated_Webcam_5M_IR: DELL M: is tagged by udev as: Keyboard
[    90.143] (II) event22 - Integrated_Webcam_5M_IR: DELL M: device is a keyboard
[    90.144] (II) config/udev: Adding input device Dell C2422HE Consumer Control (/dev/input/event28)
[    90.144] (**) Dell C2422HE Consumer Control: Applying InputClass "libinput keyboard catchall"
[    90.144] (II) Using input driver 'libinput' for 'Dell C2422HE Consumer Control'
[    90.144] (**) Dell C2422HE Consumer Control: always reports core events
[    90.144] (**) Option "Device" "/dev/input/event28"
[    90.146] (II) event28 - Dell C2422HE Consumer Control: is tagged by udev as: Keyboard
[    90.146] (II) event28 - Dell C2422HE Consumer Control: device is a keyboard
[    90.147] (II) event28 - Dell C2422HE Consumer Control: device removed
[    90.190] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7.2/3-7.2.3/3-7.2.3.3/3-7.2.3.3:1.3/0003:413C:C00B.0008/input/input37/event28"
[    90.191] (II) XINPUT: Adding extended input device "Dell C2422HE Consumer Control" (type: KEYBOARD, id 26)
[    90.193] (II) event28 - Dell C2422HE Consumer Control: is tagged by udev as: Keyboard
[    90.193] (II) event28 - Dell C2422HE Consumer Control: device is a keyboard
[    90.195] (II) config/udev: Adding input device Dell C2422HE (/dev/input/event29)
[    90.195] (II) No input driver specified, ignoring this device.
[    90.195] (II) This device may have been added with another device file.
[    90.195] (II) config/udev: Adding input device Dell C2422HE (/dev/input/event30)
[    90.195] (**) Dell C2422HE: Applying InputClass "libinput keyboard catchall"
[    90.195] (II) Using input driver 'libinput' for 'Dell C2422HE'
[    90.195] (**) Dell C2422HE: always reports core events
[    90.196] (**) Option "Device" "/dev/input/event30"
[    90.198] (II) event30 - Dell C2422HE: is tagged by udev as: Keyboard
[    90.198] (II) event30 - Dell C2422HE: device is a keyboard
[    90.198] (II) event30 - Dell C2422HE: device removed
[    90.240] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7.2/3-7.2.3/3-7.2.3.3/3-7.2.3.3:1.3/0003:413C:C00B.0008/input/input39/event30"
[    90.240] (II) XINPUT: Adding extended input device "Dell C2422HE" (type: KEYBOARD, id 27)
[    90.243] (II) event30 - Dell C2422HE: is tagged by udev as: Keyboard
[    90.243] (II) event30 - Dell C2422HE: device is a keyboard
[   297.624] (II) event28 - Dell C2422HE Consumer Control: device removed
[   297.657] (II) config/udev: removing device Dell C2422HE Consumer Control
[   297.658] (II) UnloadModule: "libinput"
[   297.721] (II) event30 - Dell C2422HE: device removed
[   297.741] (II) config/udev: removing device Dell C2422HE
[   297.741] (II) UnloadModule: "libinput"
[   297.761] (II) event21 - Integrated_Webcam_5M_IR: DELL M: device removed
[   297.804] (II) config/udev: removing device Integrated_Webcam_5M_IR: DELL M
[   297.804] (II) UnloadModule: "libinput"
[   297.824] (II) event22 - Integrated_Webcam_5M_IR: DELL M: device removed
[   297.844] (II) config/udev: removing device Integrated_Webcam_5M_IR: DELL M
[   297.844] (II) UnloadModule: "libinput"
[   298.783] (II) config/udev: Adding input device Dell C2422HE (/dev/input/event28)
[   298.783] (**) Dell C2422HE: Applying InputClass "libinput keyboard catchall"
[   298.783] (II) Using input driver 'libinput' for 'Dell C2422HE'
[   298.783] (**) Dell C2422HE: always reports core events
[   298.783] (**) Option "Device" "/dev/input/event28"
[   298.786] (II) event28 - Dell C2422HE: is tagged by udev as: Keyboard
[   298.786] (II) event28 - Dell C2422HE: device is a keyboard
[   298.786] (II) event28 - Dell C2422HE: device removed
[   298.814] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7.2/3-7.2.3/3-7.2.3.3/3-7.2.3.3:1.3/0003:413C:C00B.000B/input/input42/event28"
[   298.814] (II) XINPUT: Adding extended input device "Dell C2422HE" (type: KEYBOARD, id 24)
[   298.849] (II) event28 - Dell C2422HE: is tagged by udev as: Keyboard
[   298.849] (II) event28 - Dell C2422HE: device is a keyboard
[   298.851] (II) config/udev: Adding input device Dell C2422HE Consumer Control (/dev/input/event21)
[   298.851] (**) Dell C2422HE Consumer Control: Applying InputClass "libinput keyboard catchall"
[   298.851] (II) Using input driver 'libinput' for 'Dell C2422HE Consumer Control'
[   298.851] (**) Dell C2422HE Consumer Control: always reports core events
[   298.851] (**) Option "Device" "/dev/input/event21"
[   298.853] (II) event21 - Dell C2422HE Consumer Control: is tagged by udev as: Keyboard
[   298.853] (II) event21 - Dell C2422HE Consumer Control: device is a keyboard
[   298.854] (II) event21 - Dell C2422HE Consumer Control: device removed
[   298.897] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7.2/3-7.2.3/3-7.2.3.3/3-7.2.3.3:1.3/0003:413C:C00B.000B/input/input40/event21"
[   298.897] (II) XINPUT: Adding extended input device "Dell C2422HE Consumer Control" (type: KEYBOARD, id 25)
[   298.900] (II) event21 - Dell C2422HE Consumer Control: is tagged by udev as: Keyboard
[   298.900] (II) event21 - Dell C2422HE Consumer Control: device is a keyboard
[   298.901] (II) config/udev: Adding input device Dell C2422HE (/dev/input/event22)
[   298.901] (II) No input driver specified, ignoring this device.
[   298.901] (II) This device may have been added with another device file.
[   299.234] (II) config/udev: Adding input device Integrated_Webcam_5M_IR: DELL M (/dev/input/event29)
[   299.234] (**) Integrated_Webcam_5M_IR: DELL M: Applying InputClass "libinput keyboard catchall"
[   299.234] (II) Using input driver 'libinput' for 'Integrated_Webcam_5M_IR: DELL M'
[   299.234] (**) Integrated_Webcam_5M_IR: DELL M: always reports core events
[   299.234] (**) Option "Device" "/dev/input/event29"
[   299.236] (II) event29 - Integrated_Webcam_5M_IR: DELL M: is tagged by udev as: Keyboard
[   299.236] (II) event29 - Integrated_Webcam_5M_IR: DELL M: device is a keyboard
[   299.237] (II) event29 - Integrated_Webcam_5M_IR: DELL M: device removed
[   299.290] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7.2/3-7.2.3/3-7.2.3.4/3-7.2.3.4:1.0/input/input43/event29"
[   299.290] (II) XINPUT: Adding extended input device "Integrated_Webcam_5M_IR: DELL M" (type: KEYBOARD, id 26)
[   299.293] (II) event29 - Integrated_Webcam_5M_IR: DELL M: is tagged by udev as: Keyboard
[   299.293] (II) event29 - Integrated_Webcam_5M_IR: DELL M: device is a keyboard
[   299.295] (II) config/udev: Adding input device Integrated_Webcam_5M_IR: DELL M (/dev/input/event30)
[   299.295] (**) Integrated_Webcam_5M_IR: DELL M: Applying InputClass "libinput keyboard catchall"
[   299.295] (II) Using input driver 'libinput' for 'Integrated_Webcam_5M_IR: DELL M'
[   299.295] (**) Integrated_Webcam_5M_IR: DELL M: always reports core events
[   299.295] (**) Option "Device" "/dev/input/event30"
[   299.297] (II) event30 - Integrated_Webcam_5M_IR: DELL M: is tagged by udev as: Keyboard
[   299.297] (II) event30 - Integrated_Webcam_5M_IR: DELL M: device is a keyboard
[   299.297] (II) event30 - Integrated_Webcam_5M_IR: DELL M: device removed
[   299.344] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7.2/3-7.2.3/3-7.2.3.4/3-7.2.3.4:1.2/input/input44/event30"
[   299.344] (II) XINPUT: Adding extended input device "Integrated_Webcam_5M_IR: DELL M" (type: KEYBOARD, id 27)
[   299.346] (II) event30 - Integrated_Webcam_5M_IR: DELL M: is tagged by udev as: Keyboard
[   299.346] (II) event30 - Integrated_Webcam_5M_IR: DELL M: device is a keyboard
[   300.941] (II) event21 - Dell C2422HE Consumer Control: device removed
[   300.964] (II) config/udev: removing device Dell C2422HE Consumer Control
[   300.965] (II) UnloadModule: "libinput"
[   301.041] (II) event28 - Dell C2422HE: device removed
[   301.061] (II) config/udev: removing device Dell C2422HE
[   301.061] (II) UnloadModule: "libinput"
[   301.077] (II) event29 - Integrated_Webcam_5M_IR: DELL M: device removed
[   301.117] (II) config/udev: removing device Integrated_Webcam_5M_IR: DELL M
[   301.117] (II) UnloadModule: "libinput"
[   301.137] (II) event30 - Integrated_Webcam_5M_IR: DELL M: device removed
[   301.160] (II) config/udev: removing device Integrated_Webcam_5M_IR: DELL M
[   301.161] (II) UnloadModule: "libinput"
[   329.222] (II) config/udev: Adding input device Dell C2422HE Consumer Control (/dev/input/event21)
[   329.222] (**) Dell C2422HE Consumer Control: Applying InputClass "libinput keyboard catchall"
[   329.222] (II) Using input driver 'libinput' for 'Dell C2422HE Consumer Control'
[   329.222] (**) Dell C2422HE Consumer Control: always reports core events
[   329.222] (**) Option "Device" "/dev/input/event21"
[   329.222] (II) event21 - Dell C2422HE Consumer Control: is tagged by udev as: Keyboard
[   329.222] (II) event21 - Dell C2422HE Consumer Control: device is a keyboard
[   329.222] (II) event21 - Dell C2422HE Consumer Control: device removed
[   329.287] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-3/3-3.3/3-3.3:1.3/0003:413C:C00B.000E/input/input45/event21"
[   329.287] (II) XINPUT: Adding extended input device "Dell C2422HE Consumer Control" (type: KEYBOARD, id 24)
[   329.289] (II) event21 - Dell C2422HE Consumer Control: is tagged by udev as: Keyboard
[   329.290] (II) event21 - Dell C2422HE Consumer Control: device is a keyboard
[   329.290] (EE) event24 - ZSA Technology Labs ErgoDox EZ: client bug: event processing lagging behind by 61ms, your system is too slow
[   329.291] (II) config/udev: Adding input device Dell C2422HE (/dev/input/event22)
[   329.291] (II) No input driver specified, ignoring this device.
[   329.291] (II) This device may have been added with another device file.
[   329.292] (II) config/udev: Adding input device Dell C2422HE (/dev/input/event28)
[   329.292] (**) Dell C2422HE: Applying InputClass "libinput keyboard catchall"
[   329.292] (II) Using input driver 'libinput' for 'Dell C2422HE'
[   329.292] (**) Dell C2422HE: always reports core events
[   329.292] (**) Option "Device" "/dev/input/event28"
[   329.309] (II) event28 - Dell C2422HE: is tagged by udev as: Keyboard
[   329.309] (II) event28 - Dell C2422HE: device is a keyboard
[   329.309] (II) event28 - Dell C2422HE: device removed
[   329.357] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-3/3-3.3/3-3.3:1.3/0003:413C:C00B.000E/input/input47/event28"
[   329.357] (II) XINPUT: Adding extended input device "Dell C2422HE" (type: KEYBOARD, id 25)
[   329.359] (II) event28 - Dell C2422HE: is tagged by udev as: Keyboard
[   329.359] (II) event28 - Dell C2422HE: device is a keyboard
[   329.713] (II) config/udev: Adding input device Integrated_Webcam_5M_IR: DELL M (/dev/input/event29)
[   329.713] (**) Integrated_Webcam_5M_IR: DELL M: Applying InputClass "libinput keyboard catchall"
[   329.713] (II) Using input driver 'libinput' for 'Integrated_Webcam_5M_IR: DELL M'
[   329.713] (**) Integrated_Webcam_5M_IR: DELL M: always reports core events
[   329.713] (**) Option "Device" "/dev/input/event29"
[   329.715] (II) event29 - Integrated_Webcam_5M_IR: DELL M: is tagged by udev as: Keyboard
[   329.715] (II) event29 - Integrated_Webcam_5M_IR: DELL M: device is a keyboard
[   329.716] (II) event29 - Integrated_Webcam_5M_IR: DELL M: device removed
[   329.767] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-3/3-3.4/3-3.4:1.0/input/input48/event29"
[   329.767] (II) XINPUT: Adding extended input device "Integrated_Webcam_5M_IR: DELL M" (type: KEYBOARD, id 26)
[   329.769] (II) event29 - Integrated_Webcam_5M_IR: DELL M: is tagged by udev as: Keyboard
[   329.769] (II) event29 - Integrated_Webcam_5M_IR: DELL M: device is a keyboard
[   329.771] (II) config/udev: Adding input device Integrated_Webcam_5M_IR: DELL M (/dev/input/event30)
[   329.771] (**) Integrated_Webcam_5M_IR: DELL M: Applying InputClass "libinput keyboard catchall"
[   329.771] (II) Using input driver 'libinput' for 'Integrated_Webcam_5M_IR: DELL M'
[   329.771] (**) Integrated_Webcam_5M_IR: DELL M: always reports core events
[   329.771] (**) Option "Device" "/dev/input/event30"
[   329.789] (II) event30 - Integrated_Webcam_5M_IR: DELL M: is tagged by udev as: Keyboard
[   329.789] (II) event30 - Integrated_Webcam_5M_IR: DELL M: device is a keyboard
[   329.789] (II) event30 - Integrated_Webcam_5M_IR: DELL M: device removed
[   329.857] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-3/3-3.4/3-3.4:1.2/input/input49/event30"
[   329.857] (II) XINPUT: Adding extended input device "Integrated_Webcam_5M_IR: DELL M" (type: KEYBOARD, id 27)
[   329.859] (II) event30 - Integrated_Webcam_5M_IR: DELL M: is tagged by udev as: Keyboard
[   329.859] (II) event30 - Integrated_Webcam_5M_IR: DELL M: device is a keyboard
[   350.250] (II) event21 - Dell C2422HE Consumer Control: device removed
[   350.274] (II) config/udev: removing device Dell C2422HE Consumer Control
[   350.274] (II) UnloadModule: "libinput"
[   350.337] (II) event28 - Dell C2422HE: device removed
[   350.360] (II) config/udev: removing device Dell C2422HE
[   350.361] (II) UnloadModule: "libinput"
[   350.381] (II) event29 - Integrated_Webcam_5M_IR: DELL M: device removed
[   350.404] (II) config/udev: removing device Integrated_Webcam_5M_IR: DELL M
[   350.404] (II) UnloadModule: "libinput"
[   350.427] (II) event30 - Integrated_Webcam_5M_IR: DELL M: device removed
[   350.467] (II) config/udev: removing device Integrated_Webcam_5M_IR: DELL M
[   350.468] (II) UnloadModule: "libinput"
[   384.054] (II) config/udev: Adding input device DP-3 (/dev/input/event21)
[   384.054] (**) DP-3: Applying InputClass "libinput keyboard catchall"
[   384.054] (II) Using input driver 'libinput' for 'DP-3'
[   384.054] (**) DP-3: always reports core events
[   384.054] (**) Option "Device" "/dev/input/event21"
[   384.054] (II) event21 - DP-3: is tagged by udev as: Keyboard Pointingstick
[   384.055] (II) event21 - DP-3: device is a pointer
[   384.055] (II) event21 - DP-3: device is a keyboard
[   384.055] (II) event21 - DP-3: device removed
[   384.087] (II) libinput: DP-3: needs a virtual subdevice
[   384.087] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:02.0/rc/rc0/input50/event21"
[   384.087] (II) XINPUT: Adding extended input device "DP-3" (type: MOUSE, id 24)
[   384.087] (**) Option "AccelerationScheme" "none"
[   384.088] (**) DP-3: (accel) selected scheme none/0
[   384.088] (**) DP-3: (accel) acceleration factor: 2.000
[   384.088] (**) DP-3: (accel) acceleration threshold: 4
[   384.089] (II) event21 - DP-3: is tagged by udev as: Keyboard Pointingstick
[   384.089] (II) event21 - DP-3: device is a pointer
[   384.089] (II) event21 - DP-3: device is a keyboard
[   384.092] (**) DP-3: Applying InputClass "libinput keyboard catchall"
[   384.092] (II) Using input driver 'libinput' for 'DP-3'
[   384.092] (**) DP-3: always reports core events
[   384.092] (**) Option "Device" "/dev/input/event21"
[   384.092] (II) libinput: DP-3: is a virtual subdevice
[   384.092] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:02.0/rc/rc0/input50/event21"
[   384.092] (II) XINPUT: Adding extended input device "DP-3" (type: KEYBOARD, id 25)
[   427.244] (II) event23 - ZSA Technology Labs ErgoDox EZ: device removed
[   427.277] (II) event24 - ZSA Technology Labs ErgoDox EZ: device removed
[   427.307] (II) config/udev: removing device ZSA Technology Labs ErgoDox EZ
[   427.307] (II) UnloadModule: "libinput"
[   427.308] (II) config/udev: removing device ZSA Technology Labs ErgoDox EZ
[   427.308] (II) UnloadModule: "libinput"
[   427.384] (II) event25 - ZSA Technology Labs ErgoDox EZ System Control: device removed
[   427.421] (II) config/udev: removing device ZSA Technology Labs ErgoDox EZ System Control
[   427.421] (II) UnloadModule: "libinput"
[   427.444] (II) event26 - ZSA Technology Labs ErgoDox EZ Consumer Control: device removed
[   427.474] (II) config/udev: removing device ZSA Technology Labs ErgoDox EZ Consumer Control
[   427.474] (II) UnloadModule: "libinput"
[   427.474] (II) config/udev: removing device ZSA Technology Labs ErgoDox EZ Consumer Control
[   427.474] (II) UnloadModule: "libinput"
[   427.627] (II) event27 - ZSA Technology Labs ErgoDox EZ Keyboard: device removed
[   427.661] (II) config/udev: removing device ZSA Technology Labs ErgoDox EZ Keyboard
[   427.661] (II) UnloadModule: "libinput"
[   435.871] (II) event21 - DP-3: device removed
[   435.891] (II) config/udev: removing device DP-3
[   435.891] (II) UnloadModule: "libinput"
[   435.891] (II) config/udev: removing device DP-3
[   435.891] (II) UnloadModule: "libinput"
[   438.471] (II) config/udev: Adding input device DP-2 (/dev/input/event21)
[   438.471] (**) DP-2: Applying InputClass "libinput keyboard catchall"
[   438.471] (II) Using input driver 'libinput' for 'DP-2'
[   438.471] (**) DP-2: always reports core events
[   438.471] (**) Option "Device" "/dev/input/event21"
[   438.471] (II) event21 - DP-2: is tagged by udev as: Keyboard Pointingstick
[   438.471] (II) event21 - DP-2: device is a pointer
[   438.471] (II) event21 - DP-2: device is a keyboard
[   438.472] (II) event21 - DP-2: device removed
[   438.497] (II) libinput: DP-2: needs a virtual subdevice
[   438.497] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:02.0/rc/rc0/input51/event21"
[   438.497] (II) XINPUT: Adding extended input device "DP-2" (type: MOUSE, id 18)
[   438.498] (**) Option "AccelerationScheme" "none"
[   438.498] (**) DP-2: (accel) selected scheme none/0
[   438.498] (**) DP-2: (accel) acceleration factor: 2.000
[   438.498] (**) DP-2: (accel) acceleration threshold: 4
[   438.499] (II) event21 - DP-2: is tagged by udev as: Keyboard Pointingstick
[   438.500] (II) event21 - DP-2: device is a pointer
[   438.500] (II) event21 - DP-2: device is a keyboard
[   438.502] (**) DP-2: Applying InputClass "libinput keyboard catchall"
[   438.502] (II) Using input driver 'libinput' for 'DP-2'
[   438.502] (**) DP-2: always reports core events
[   438.502] (**) Option "Device" "/dev/input/event21"
[   438.502] (II) libinput: DP-2: is a virtual subdevice
[   438.502] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:02.0/rc/rc0/input51/event21"
[   438.502] (II) XINPUT: Adding extended input device "DP-2" (type: KEYBOARD, id 19)
[   445.294] (EE) event8  - MSFT0001:00 04F3:317C Touchpad: kernel bug: Touch jump detected and discarded.
See https://wayland.freedesktop.org/libinput/doc/1.21.0/touchpad-jumping-cursors.html for details
[   457.197] (II) config/udev: Adding input device GN Netcom A/S Jabra EVOLVE LINK MS (/dev/input/event22)
[   457.197] (**) GN Netcom A/S Jabra EVOLVE LINK MS: Applying InputClass "libinput keyboard catchall"
[   457.197] (II) Using input driver 'libinput' for 'GN Netcom A/S Jabra EVOLVE LINK MS'
[   457.197] (**) GN Netcom A/S Jabra EVOLVE LINK MS: always reports core events
[   457.197] (**) Option "Device" "/dev/input/event22"
[   457.199] (II) event22 - GN Netcom A/S Jabra EVOLVE LINK MS: is tagged by udev as: Keyboard
[   457.199] (II) event22 - GN Netcom A/S Jabra EVOLVE LINK MS: device is a keyboard
[   457.200] (II) event22 - GN Netcom A/S Jabra EVOLVE LINK MS: device removed
[   457.247] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7.2/3-7.2.1/3-7.2.1:1.3/0003:0B0E:0305.0011/input/input52/event22"
[   457.247] (II) XINPUT: Adding extended input device "GN Netcom A/S Jabra EVOLVE LINK MS" (type: KEYBOARD, id 20)
[   457.250] (II) event22 - GN Netcom A/S Jabra EVOLVE LINK MS: is tagged by udev as: Keyboard
[   457.250] (II) event22 - GN Netcom A/S Jabra EVOLVE LINK MS: device is a keyboard
[   457.411] (II) config/udev: Adding input device ZSA Technology Labs ErgoDox EZ (/dev/input/mouse3)
[   457.411] (II) No input driver specified, ignoring this device.
[   457.411] (II) This device may have been added with another device file.
[   457.474] (II) config/udev: Adding input device ZSA Technology Labs ErgoDox EZ Keyboard (/dev/input/event27)
[   457.474] (**) ZSA Technology Labs ErgoDox EZ Keyboard: Applying InputClass "libinput keyboard catchall"
[   457.474] (II) Using input driver 'libinput' for 'ZSA Technology Labs ErgoDox EZ Keyboard'
[   457.474] (**) ZSA Technology Labs ErgoDox EZ Keyboard: always reports core events
[   457.474] (**) Option "Device" "/dev/input/event27"
[   457.476] (II) event27 - ZSA Technology Labs ErgoDox EZ Keyboard: is tagged by udev as: Keyboard
[   457.476] (II) event27 - ZSA Technology Labs ErgoDox EZ Keyboard: device is a keyboard
[   457.477] (II) event27 - ZSA Technology Labs ErgoDox EZ Keyboard: device removed
[   457.520] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7.2/3-7.2.4/3-7.2.4:1.3/0003:3297:4974.0015/input/input57/event27"
[   457.521] (II) XINPUT: Adding extended input device "ZSA Technology Labs ErgoDox EZ Keyboard" (type: KEYBOARD, id 21)
[   457.523] (II) event27 - ZSA Technology Labs ErgoDox EZ Keyboard: is tagged by udev as: Keyboard
[   457.523] (II) event27 - ZSA Technology Labs ErgoDox EZ Keyboard: device is a keyboard
[   457.525] (II) config/udev: Adding input device ZSA Technology Labs ErgoDox EZ (/dev/input/event23)
[   457.525] (**) ZSA Technology Labs ErgoDox EZ: Applying InputClass "libinput keyboard catchall"
[   457.525] (II) Using input driver 'libinput' for 'ZSA Technology Labs ErgoDox EZ'
[   457.525] (**) ZSA Technology Labs ErgoDox EZ: always reports core events
[   457.525] (**) Option "Device" "/dev/input/event23"
[   457.527] (II) event23 - ZSA Technology Labs ErgoDox EZ: is tagged by udev as: Keyboard
[   457.527] (II) event23 - ZSA Technology Labs ErgoDox EZ: device is a keyboard
[   457.528] (II) event23 - ZSA Technology Labs ErgoDox EZ: device removed
[   457.561] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7.2/3-7.2.4/3-7.2.4:1.0/0003:3297:4974.0012/input/input53/event23"
[   457.561] (II) XINPUT: Adding extended input device "ZSA Technology Labs ErgoDox EZ" (type: KEYBOARD, id 22)
[   457.563] (II) event23 - ZSA Technology Labs ErgoDox EZ: is tagged by udev as: Keyboard
[   457.563] (II) event23 - ZSA Technology Labs ErgoDox EZ: device is a keyboard
[   457.565] (II) config/udev: Adding input device ZSA Technology Labs ErgoDox EZ Consumer Control (/dev/input/event26)
[   457.565] (**) ZSA Technology Labs ErgoDox EZ Consumer Control: Applying InputClass "libinput keyboard catchall"
[   457.565] (II) Using input driver 'libinput' for 'ZSA Technology Labs ErgoDox EZ Consumer Control'
[   457.565] (**) ZSA Technology Labs ErgoDox EZ Consumer Control: always reports core events
[   457.565] (**) Option "Device" "/dev/input/event26"
[   457.567] (II) event26 - ZSA Technology Labs ErgoDox EZ Consumer Control: is tagged by udev as: Keyboard
[   457.567] (II) event26 - ZSA Technology Labs ErgoDox EZ Consumer Control: device is a keyboard
[   457.568] (II) event26 - ZSA Technology Labs ErgoDox EZ Consumer Control: device removed
[   457.601] (II) libinput: ZSA Technology Labs ErgoDox EZ Consumer Control: needs a virtual subdevice
[   457.601] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7.2/3-7.2.4/3-7.2.4:1.3/0003:3297:4974.0015/input/input56/event26"
[   457.601] (II) XINPUT: Adding extended input device "ZSA Technology Labs ErgoDox EZ Consumer Control" (type: MOUSE, id 23)
[   457.601] (**) Option "AccelerationScheme" "none"
[   457.601] (**) ZSA Technology Labs ErgoDox EZ Consumer Control: (accel) selected scheme none/0
[   457.601] (**) ZSA Technology Labs ErgoDox EZ Consumer Control: (accel) acceleration factor: 2.000
[   457.601] (**) ZSA Technology Labs ErgoDox EZ Consumer Control: (accel) acceleration threshold: 4
[   457.603] (II) event26 - ZSA Technology Labs ErgoDox EZ Consumer Control: is tagged by udev as: Keyboard
[   457.603] (II) event26 - ZSA Technology Labs ErgoDox EZ Consumer Control: device is a keyboard
[   457.604] (**) ZSA Technology Labs ErgoDox EZ Consumer Control: Applying InputClass "libinput keyboard catchall"
[   457.604] (II) Using input driver 'libinput' for 'ZSA Technology Labs ErgoDox EZ Consumer Control'
[   457.604] (**) ZSA Technology Labs ErgoDox EZ Consumer Control: always reports core events
[   457.604] (**) Option "Device" "/dev/input/event26"
[   457.604] (II) libinput: ZSA Technology Labs ErgoDox EZ Consumer Control: is a virtual subdevice
[   457.604] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7.2/3-7.2.4/3-7.2.4:1.3/0003:3297:4974.0015/input/input56/event26"
[   457.604] (II) XINPUT: Adding extended input device "ZSA Technology Labs ErgoDox EZ Consumer Control" (type: KEYBOARD, id 24)
[   457.605] (II) config/udev: Adding input device ZSA Technology Labs ErgoDox EZ System Control (/dev/input/event25)
[   457.605] (**) ZSA Technology Labs ErgoDox EZ System Control: Applying InputClass "libinput keyboard catchall"
[   457.605] (II) Using input driver 'libinput' for 'ZSA Technology Labs ErgoDox EZ System Control'
[   457.605] (**) ZSA Technology Labs ErgoDox EZ System Control: always reports core events
[   457.605] (**) Option "Device" "/dev/input/event25"
[   457.607] (II) event25 - ZSA Technology Labs ErgoDox EZ System Control: is tagged by udev as: Keyboard
[   457.607] (II) event25 - ZSA Technology Labs ErgoDox EZ System Control: device is a keyboard
[   457.608] (II) event25 - ZSA Technology Labs ErgoDox EZ System Control: device removed
[   457.631] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7.2/3-7.2.4/3-7.2.4:1.3/0003:3297:4974.0015/input/input55/event25"
[   457.631] (II) XINPUT: Adding extended input device "ZSA Technology Labs ErgoDox EZ System Control" (type: KEYBOARD, id 25)
[   457.633] (II) event25 - ZSA Technology Labs ErgoDox EZ System Control: is tagged by udev as: Keyboard
[   457.633] (II) event25 - ZSA Technology Labs ErgoDox EZ System Control: device is a keyboard
[   457.635] (II) config/udev: Adding input device ZSA Technology Labs ErgoDox EZ (/dev/input/event24)
[   457.635] (**) ZSA Technology Labs ErgoDox EZ: Applying InputClass "libinput pointer catchall"
[   457.635] (II) Using input driver 'libinput' for 'ZSA Technology Labs ErgoDox EZ'
[   457.635] (**) ZSA Technology Labs ErgoDox EZ: always reports core events
[   457.635] (**) Option "Device" "/dev/input/event24"
[   457.693] (II) event24 - ZSA Technology Labs ErgoDox EZ: is tagged by udev as: Mouse
[   457.693] (II) event24 - ZSA Technology Labs ErgoDox EZ: device is a pointer
[   457.694] (II) event24 - ZSA Technology Labs ErgoDox EZ: device removed
[   457.751] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7.2/3-7.2.4/3-7.2.4:1.2/0003:3297:4974.0014/input/input54/event24"
[   457.751] (II) XINPUT: Adding extended input device "ZSA Technology Labs ErgoDox EZ" (type: MOUSE, id 26)
[   457.751] (**) Option "AccelerationScheme" "none"
[   457.751] (**) ZSA Technology Labs ErgoDox EZ: (accel) selected scheme none/0
[   457.751] (**) ZSA Technology Labs ErgoDox EZ: (accel) acceleration factor: 2.000
[   457.751] (**) ZSA Technology Labs ErgoDox EZ: (accel) acceleration threshold: 4
[   457.809] (II) event24 - ZSA Technology Labs ErgoDox EZ: is tagged by udev as: Mouse
[   457.809] (II) event24 - ZSA Technology Labs ErgoDox EZ: device is a pointer
[   900.364] (II) event21 - DP-2: device removed
[   900.380] (II) config/udev: removing device DP-2
[   900.380] (II) UnloadModule: "libinput"
[   900.381] (II) config/udev: removing device DP-2
[   900.381] (II) UnloadModule: "libinput"
[  2020.541] (II) config/udev: Adding input device DP-3 (/dev/input/event21)
[  2020.541] (**) DP-3: Applying InputClass "libinput keyboard catchall"
[  2020.541] (II) Using input driver 'libinput' for 'DP-3'
[  2020.541] (**) DP-3: always reports core events
[  2020.541] (**) Option "Device" "/dev/input/event21"
[  2020.542] (II) event21 - DP-3: is tagged by udev as: Keyboard Pointingstick
[  2020.543] (II) event21 - DP-3: device is a pointer
[  2020.543] (II) event21 - DP-3: device is a keyboard
[  2020.545] (II) event21 - DP-3: device removed
[  2020.570] (II) libinput: DP-3: needs a virtual subdevice
[  2020.570] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:02.0/rc/rc0/input58/event21"
[  2020.570] (II) XINPUT: Adding extended input device "DP-3" (type: MOUSE, id 18)
[  2020.571] (**) Option "AccelerationScheme" "none"
[  2020.571] (**) DP-3: (accel) selected scheme none/0
[  2020.571] (**) DP-3: (accel) acceleration factor: 2.000
[  2020.571] (**) DP-3: (accel) acceleration threshold: 4
[  2020.572] (II) event21 - DP-3: is tagged by udev as: Keyboard Pointingstick
[  2020.572] (II) event21 - DP-3: device is a pointer
[  2020.572] (II) event21 - DP-3: device is a keyboard
[  2020.575] (**) DP-3: Applying InputClass "libinput keyboard catchall"
[  2020.575] (II) Using input driver 'libinput' for 'DP-3'
[  2020.575] (**) DP-3: always reports core events
[  2020.575] (**) Option "Device" "/dev/input/event21"
[  2020.575] (II) libinput: DP-3: is a virtual subdevice
[  2020.575] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:02.0/rc/rc0/input58/event21"
[  2020.575] (II) XINPUT: Adding extended input device "DP-3" (type: KEYBOARD, id 19)

Offline

#7 2022-11-01 14:28:17

prayner96
Member
Registered: 2022-03-06
Posts: 72

Re: External monitors not detected

Below is the output of "dmesg -w" after plugging in USB-C to HDMI cable.

[ 2988.844503] Registered IR keymap rc-cec
[ 2988.844611] rc rc0: DP-2 as /devices/pci0000:00/0000:00:02.0/rc/rc0
[ 2988.844705] input: DP-2 as /devices/pci0000:00/0000:00:02.0/rc/rc0/input60
[ 2995.757036] usb usb2-port2: attempt power cycle
[ 3004.190319] usb usb2-port2: unable to enumerate USB device

Offline

#8 2022-11-01 14:35:45

prayner96
Member
Registered: 2022-03-06
Posts: 72

Re: External monitors not detected

I'm not sure if you are able to access the URL for the `sudo journalctl -b | curl -F 'file=@-' 0x0.st`

http://0x0.st/oYRL.txt

Offline

#9 2022-11-01 14:42:11

seth
Member
From: Don't DM me only for attention
Registered: 2012-09-03
Posts: 72,920

Re: External monitors not detected

There're tons of 

Nov 01 14:39:05 bazmorty modprobe[1790]: modprobe: FATAL: Module evdi not found in directory /lib/modules/6.0.6-arch1-1

This is a dkms package, do you have linux-headers installed?

dkms status

https://wiki.archlinux.org/title/Dynami … le_Support

How to upload text · How to boot w/o GUI · Disable Windows Fast-Start! · Fix your xinitrc

Offline

#10 2022-11-01 18:07:45

prayner96
Member
Registered: 2022-03-06
Posts: 72

Re: External monitors not detected

$ sudo pacman -Q linux-headers
error: package 'linux-headers' was not found

dkms status does not have an output.

$ dkms status
$ sudo pacman -Q dkms
dkms 3.0.7-1

Are you implying that I should install linux-headers and build a module?

Offline

#11 2022-11-01 19:24:34

seth
Member
From: Don't DM me only for attention
Registered: 2012-09-03
Posts: 72,920

Re: External monitors not detected

That was the idea wink
You're gonna need that module.

How to upload text · How to boot w/o GUI · Disable Windows Fast-Start! · Fix your xinitrc

Offline

#12 2022-11-06 13:39:28

prayner96
Member
Registered: 2022-03-06
Posts: 72

Re: External monitors not detected

I re-read the Arch wiki instructions and figured that I installed the evdi package incorrectly. I re-installed evdi-git and then enabled displaylink. Laptop successfully outputs to external monitor using USB-C to HDMI cable directly, but not via the displayport. The external monitor image is zoomed in on the top left of the screen (see IRL photo of monitor). The external monitor is full HD while the laptop has 2K+ resolution and 16:10 display. My guess is that I need to solve this resolution issue using xrandr. Will spend more time researching but I think I´m on the right path.

Below I am sharing the latest outputs of the diagnostic tools previously suggested.

[16775.267301] usb 3-7.2.3: new high-speed USB device number 14 using xhci_hcd
[16775.388427] usb 3-7.2.3: New USB device found, idVendor=0bda, idProduct=5409, bcdDevice= 1.48
[16775.388437] usb 3-7.2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[16775.388440] usb 3-7.2.3: Product: USB2.1 Hub
[16775.388442] usb 3-7.2.3: Manufacturer: Generic
[16775.390354] hub 3-7.2.3:1.0: USB hub found
[16775.391929] hub 3-7.2.3:1.0: 6 ports detected
[16775.807305] usb 3-7.2.3.5: new high-speed USB device number 15 using xhci_hcd
[16775.927132] usb 3-7.2.3.5: New USB device found, idVendor=0bda, idProduct=5418, bcdDevice= 1.01
[16775.927142] usb 3-7.2.3.5: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[16775.927145] usb 3-7.2.3.5: Product: BillBoard Device
[16775.927147] usb 3-7.2.3.5: Manufacturer: Realtek
[16776.017299] usb 3-7.2.3.6: new high-speed USB device number 16 using xhci_hcd
[16776.139030] usb 3-7.2.3.6: New USB device found, idVendor=0bda, idProduct=1101, bcdDevice= 1.01
[16776.139040] usb 3-7.2.3.6: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[16776.139043] usb 3-7.2.3.6: Product: HID Device
[16776.139045] usb 3-7.2.3.6: Manufacturer: Realtek
[16776.145265] hid-generic 0003:0BDA:1101.000B: hiddev97,hidraw6: USB HID v1.11 Device [Realtek HID Device] on usb-0000:00:14.0-7.2.3.6/input0
[16776.224362] usb 3-7.2.4: reset full-speed USB device number 6 using xhci_hcd
[16776.403987] usb 3-7.2.3.1: new high-speed USB device number 17 using xhci_hcd
[16776.532211] usb 3-7.2.3.1: New USB device found, idVendor=0bda, idProduct=5409, bcdDevice= 1.40
[16776.532221] usb 3-7.2.3.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[16776.532225] usb 3-7.2.3.1: Product: USB2.1 Hub
[16776.532227] usb 3-7.2.3.1: Manufacturer: Generic
[16776.534516] hub 3-7.2.3.1:1.0: USB hub found
[16776.536378] hub 3-7.2.3.1:1.0: 5 ports detected
[16776.750633] usb 3-7.2.3.2: new high-speed USB device number 18 using xhci_hcd
[16776.842918] usb 3-7.2.3.2: New USB device found, idVendor=0bda, idProduct=8153, bcdDevice=31.00
[16776.842928] usb 3-7.2.3.2: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[16776.842931] usb 3-7.2.3.2: Product: USB 10/100/1000 LAN
[16776.842933] usb 3-7.2.3.2: Manufacturer: Realtek
[16776.842935] usb 3-7.2.3.2: SerialNumber: 001000001
[16776.913984] usb 3-7.2.3.1.5: new high-speed USB device number 19 using xhci_hcd
[16777.027881] usb 3-7.2.3.1.5: New USB device found, idVendor=0bda, idProduct=1100, bcdDevice= 1.01
[16777.027890] usb 3-7.2.3.1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[16777.027893] usb 3-7.2.3.1.5: Product: HID Device
[16777.027895] usb 3-7.2.3.1.5: Manufacturer: Realtek
[16777.034690] hid-generic 0003:0BDA:1100.000C: hiddev98,hidraw7: USB HID v1.11 Device [Realtek HID Device] on usb-0000:00:14.0-7.2.3.1.5/input0
[16777.104369] usb 3-7.2.3.2: reset high-speed USB device number 18 using xhci_hcd
[16777.222585] r8152 3-7.2.3.2:1.0: load rtl8153b-2 v1 10/23/19 successfully
[16777.258393] r8152 3-7.2.3.2:1.0 eth0: v1.12.13
[16777.267287] usb 3-7.2.3.3: new full-speed USB device number 20 using xhci_hcd
[16777.382762] usb 3-7.2.3.3: New USB device found, idVendor=413c, idProduct=c00b, bcdDevice= 0.07
[16777.382771] usb 3-7.2.3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[16777.382774] usb 3-7.2.3.3: Product: C2422HE
[16777.382777] usb 3-7.2.3.3: Manufacturer: Dell
[16777.382779] usb 3-7.2.3.3: SerialNumber: MH4KG1COBJRL
[16777.425333] usb 3-7.2.3.3: Warning! Unlikely big volume range (=18944), cval->res is probably wrong.
[16777.425341] usb 3-7.2.3.3: [2] FU [Headset Playback Volume] ch = 2, val = -18944/0/1
[16777.438921] usb 3-7.2.3.3: Warning! Unlikely big volume range (=18944), cval->res is probably wrong.
[16777.438928] usb 3-7.2.3.3: [6] FU [Headset Capture Volume] ch = 2, val = -18944/0/1
[16777.441810] input: Dell C2422HE Consumer Control as /devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7.2/3-7.2.3/3-7.2.3.3/3-7.2.3.3:1.3/0003:413C:C00B.000D/input/input39
[16777.497539] input: Dell C2422HE as /devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7.2/3-7.2.3/3-7.2.3.3/3-7.2.3.3:1.3/0003:413C:C00B.000D/input/input40
[16777.497766] input: Dell C2422HE as /devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7.2/3-7.2.3/3-7.2.3.3/3-7.2.3.3:1.3/0003:413C:C00B.000D/input/input41
[16777.498294] hid-generic 0003:413C:C00B.000D: input,hiddev99,hidraw8: USB HID v1.11 Device [Dell C2422HE] on usb-0000:00:14.0-7.2.3.3/input3
$ dkms status
evdi/1.12.0, 6.0.7-arch1-1, x86_64: installed

Previously there was no output to this message.

$ xrandr
Screen 0: minimum 8 x 8, current 2880 x 1800, maximum 32767 x 32767
eDP1 connected primary 2880x1800+0+0 (normal left inverted right x axis y axis) 300mm x 190mm
   2880x1800     90.01*+
   2880x1620     59.96    59.97  
   2560x1600     59.99    59.97  
   2560x1440     59.96    59.95  
   2048x1536     85.00    75.00    60.00  
   1920x1440     85.00    75.00    60.00  
   1856x1392     75.00    60.01  
   1792x1344     75.00    60.01  
   2048x1152     59.90    59.91  
   1920x1200     90.00    59.88    59.95  
   1920x1080     59.96    59.93  
   1600x1200     85.00    75.00    70.00    65.00    60.00  
   1680x1050     90.00    59.95    59.88  
   1400x1050     74.76    59.98  
   1600x900      59.95    59.82  
   1280x1024     85.02    75.02    60.02  
   1440x900      90.00  
   1400x900      90.00    59.96    59.88  
   1280x960      85.00    60.00  
   1368x768      59.88    59.85  
   1280x800      90.00    59.81    59.91  
   1152x864      75.00  
   1280x720      59.86    59.74  
   1024x768      85.00    75.03    70.07    60.00  
   1024x768i     86.96  
   1024x576      59.90    59.82  
   832x624       74.55  
   960x540       59.63    59.82  
   800x600       85.14    72.19    75.00    60.32    56.25  
   864x486       59.92    59.57  
   640x480       85.01    72.81    75.00    59.94  
   720x405       59.51    58.99  
   720x400       85.04  
   640x400       85.08  
   640x360       59.84    59.32  
   640x350       85.08  
DP1 disconnected (normal left inverted right x axis y axis)
DP2 connected 1920x1080+0+0 (normal left inverted right x axis y axis) 530mm x 300mm
   1920x1080     60.00*+  50.00    59.94  
   1920x1080i    60.00    50.00    59.94  
   1600x900      60.00  
   1280x1024     75.02    60.02  
   1152x864      75.00  
   1280x720      60.00    50.00    59.94  
   1024x768      75.03    60.00  
   800x600       75.00    60.32  
   720x576       50.00  
   720x480       60.00    59.94  
   640x480       75.00    60.00    59.94  
   720x400       70.08  
DP3 disconnected (normal left inverted right x axis y axis)
DP4 disconnected (normal left inverted right x axis y axis)
VIRTUAL1 disconnected (normal left inverted right x axis y axis)

Ext. monitor is now detected.

http://0x0.st/oEaz.txt

No longer seeing the modprobe error.

Offline

Pages: 1

Board footer

Powered by FluxBB