You are not logged in.
- Topics: Active | Unanswered
#1 2023-05-16 20:23:03
- priyoislam
- Member
- Registered: 2023-05-16
- Posts: 2
Input/output error while recovering journal of /dev/sda2
Hi ,
the initial screen showing this :
error: failure writing sector 0xe4de020 to 'hd0'
Press any key to continuethen
/dev/sda2: UNEXPECTED INCONSISTENCY; RUN fsck MANUALLY"when i run fsck it show following error:
fsck from util-linux 2.38.1
e2fsck 1.47.0 (5-Feb-2023)
/dev/sda2: recovering journal
fsck.ext4: Input/output error while recovering journal of /dev/sda2
fsck.ext4: unable to set superblock flags on /dev/sda2
/dev/sda2: ********** WARNING: Filesystem still has errori also tried in live env with a usb . same problem occurred.
this is the
sudo smartctl -a /dev/sda2 result :
smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.25-1-MANJARO] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, [url=http://www.smartmontools.org]www.smartmontools.org[/url]
=== START OF INFORMATION SECTION ===
Model Family: Marvell based SanDisk SSDs
Device Model: SanDisk SDSSDH31024G
Serial Number: 19118D800161
LU WWN Device Id: 5 001b44 8b86ef648
Firmware Version: X6107000
User Capacity: 1,024,209,543,168 bytes [1.02 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
TRIM Command: Available, deterministic, zeroed
Device is: In smartctl database 7.3/5319
ATA Version is: ACS-4 T13/BSR INCITS 529 revision 5
SATA Version is: SATA 3.3, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Tue May 16 20:09:52 2023 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x11) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 10) minutes.
SMART Attributes Data Structure revision number: 4
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
5 Reallocated_Sector_Ct 0x0032 100 100 --- Old_age Always - 1
9 Power_On_Hours 0x0032 100 100 --- Old_age Always - 11461
12 Power_Cycle_Count 0x0032 100 100 --- Old_age Always - 3291
165 Total_Write/Erase_Count 0x0032 100 100 --- Old_age Always - 537016141549
166 Min_W/E_Cycle 0x0032 100 100 --- Old_age Always - 8
167 Min_Bad_Block/Die 0x0032 100 100 --- Old_age Always - 125
168 Maximum_Erase_Cycle 0x0032 100 100 --- Old_age Always - 53
169 Total_Bad_Block 0x0032 100 100 --- Old_age Always - 1473
170 Unknown_Marvell_Attr 0x0032 100 100 --- Old_age Always - 1
171 Program_Fail_Count 0x0032 100 100 --- Old_age Always - 0
172 Erase_Fail_Count 0x0032 100 100 --- Old_age Always - 0
173 Avg_Write/Erase_Count 0x0032 100 100 --- Old_age Always - 24
174 Unexpect_Power_Loss_Ct 0x0032 100 100 --- Old_age Always - 181
184 End-to-End_Error 0x0032 100 100 --- Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 --- Old_age Always - 0
188 Command_Timeout 0x0032 100 100 --- Old_age Always - 0
194 Temperature_Celsius 0x0022 064 055 --- Old_age Always - 36 (Min/Max 17/55)
199 SATA_CRC_Error 0x0032 100 100 --- Old_age Always - 0
230 Perc_Write/Erase_Count 0x0032 100 100 --- Old_age Always - 822 552 822
232 Perc_Avail_Resrvd_Space 0x0033 100 100 004 Pre-fail Always - 100
233 Total_NAND_Writes_GiB 0x0032 100 100 --- Old_age Always - 25279
234 Perc_Write/Erase_Ct_BC 0x0032 100 100 --- Old_age Always - 28955
241 Total_Writes_GiB 0x0030 253 253 --- Old_age Offline - 15410
242 Total_Reads_GiB 0x0030 253 253 --- Old_age Offline - 13984
244 Thermal_Throttle 0x0032 000 100 --- Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 11460 -
# 2 Short offline Completed without error 00% 2445 -
Selective Self-tests/Logging not supportedCan anyone help me with this problem . I tried some previous solution . I tried badblocks but it was too time consuming like it completed 0.8% in 1 hour. So i wanted to try any faster solution first.
Thank you.
Last edited by priyoislam (2023-05-16 20:25:27)
Offline
#2 2023-05-16 21:14:52
- seth
- Member
- Registered: 2012-09-03
- Posts: 51,213
Re: Input/output error while recovering journal of /dev/sda2
Check dmesg for errors when trying to read/write from/to the device.
If the disk isn't toast there'S probably an issue w/ the bus (cable)
Badblocks in destructive mode is significantly faster, but will erase all your data.
And if there's a physical problem slwoing down the IO w/ massive amounts of errors, any kind of test is gonna be slow because of that.
Offline
#3 2023-05-17 08:46:29
- priyoislam
- Member
- Registered: 2023-05-16
- Posts: 2
Re: Input/output error while recovering journal of /dev/sda2
dmesg output:
603.878435] ata1.00: cmd 35/00:08:48:70:2f/00:00:5f:00:00/e0 tag 5 dma 4096 out
res 51/04:08:48:70:2f/00:00:5f:00:00/e0 Emask 0x1 (device error)
[ 603.878457] ata1.00: status: { DRDY ERR }
[ 603.878462] ata1.00: error: { ABRT }
[ 603.889152] ahci 0000:00:17.0: port does not support device sleep
[ 603.895753] ata1.00: configured for UDMA/100
[ 603.906180] ahci 0000:00:17.0: port does not support device sleep
[ 603.906364] ata1: EH complete
[ 603.938360] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 603.938387] ata1.00: irq_stat 0x40000001
[ 603.938392] ata1: SError: { CommWake }
[ 603.938403] ata1.00: failed command: WRITE DMA EXT
[ 603.938408] ata1.00: cmd 35/00:08:08:70:af/00:00:61:00:00/e0 tag 10 dma 4096 out
res 51/04:08:08:70:af/00:00:61:00:00/e0 Emask 0x1 (device error)
[ 603.938429] ata1.00: status: { DRDY ERR }
[ 603.938434] ata1.00: error: { ABRT }
[ 603.948708] ahci 0000:00:17.0: port does not support device sleep
[ 603.954976] ata1.00: configured for UDMA/100
[ 603.965141] ahci 0000:00:17.0: port does not support device sleep
[ 603.965326] ata1: EH complete
[ 603.998393] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 603.998408] ata1.00: irq_stat 0x40000001
[ 603.998413] ata1: SError: { CommWake }
[ 603.998424] ata1.00: failed command: WRITE DMA EXT
[ 603.998428] ata1.00: cmd 35/00:08:78:70:ef/00:00:5f:00:00/e0 tag 13 dma 4096 out
res 51/04:08:78:70:ef/00:00:5f:00:00/e0 Emask 0x1 (device error)
[ 603.998449] ata1.00: status: { DRDY ERR }
[ 603.998454] ata1.00: error: { ABRT }
[ 604.009153] ahci 0000:00:17.0: port does not support device sleep
[ 604.015806] ata1.00: configured for UDMA/100
[ 604.026246] ahci 0000:00:17.0: port does not support device sleep
[ 604.026445] ata1: EH complete
[ 604.058348] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 604.058364] ata1.00: irq_stat 0x40000001
[ 604.058369] ata1: SError: { CommWake }
[ 604.058380] ata1.00: failed command: WRITE DMA EXT
[ 604.058385] ata1.00: cmd 35/00:08:78:70:ef/00:00:5c:00:00/e0 tag 15 dma 4096 out
res 51/04:08:78:70:ef/00:00:5c:00:00/e0 Emask 0x1 (device error)
[ 604.058407] ata1.00: status: { DRDY ERR }
[ 604.058412] ata1.00: error: { ABRT }
[ 604.069101] ahci 0000:00:17.0: port does not support device sleep
[ 604.075438] ata1.00: configured for UDMA/100
[ 604.085746] ahci 0000:00:17.0: port does not support device sleep
[ 604.085853] ata1: EH complete
[ 604.118396] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 604.118412] ata1.00: irq_stat 0x40000001
[ 604.118417] ata1: SError: { CommWake }
[ 604.118428] ata1.00: failed command: WRITE DMA EXT
[ 604.118433] ata1.00: cmd 35/00:10:58:70:2f/00:00:59:00:00/e0 tag 20 dma 8192 out
res 51/04:10:58:70:2f/00:00:59:00:00/e0 Emask 0x1 (device error)
[ 604.118455] ata1.00: status: { DRDY ERR }
[ 604.118460] ata1.00: error: { ABRT }
[ 604.129174] ahci 0000:00:17.0: port does not support device sleep
[ 604.135805] ata1.00: configured for UDMA/100
[ 604.146241] ahci 0000:00:17.0: port does not support device sleep
[ 604.146442] ata1: EH complete
[ 604.178346] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 604.178361] ata1.00: irq_stat 0x40000001
[ 604.178366] ata1: SError: { CommWake }
[ 604.178378] ata1.00: failed command: WRITE DMA EXT
[ 604.178383] ata1.00: cmd 35/00:10:d0:7d:b0/00:00:56:00:00/e0 tag 25 dma 8192 out
res 51/04:10:d0:7d:b0/00:00:56:00:00/e0 Emask 0x1 (device error)
[ 604.178404] ata1.00: status: { DRDY ERR }
[ 604.178409] ata1.00: error: { ABRT }
[ 604.189094] ahci 0000:00:17.0: port does not support device sleep
[ 604.195078] ata1.00: configured for UDMA/100
[ 604.205324] ahci 0000:00:17.0: port does not support device sleep
[ 604.205432] ata1: EH complete
[ 604.238413] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 604.238429] ata1.00: irq_stat 0x40000001
[ 604.238434] ata1: SError: { CommWake }
[ 604.238447] ata1.00: failed command: WRITE DMA EXT
[ 604.238452] ata1.00: cmd 35/00:08:00:71:af/00:00:56:00:00/e0 tag 29 dma 4096 out
res 51/04:08:00:71:af/00:00:56:00:00/e0 Emask 0x1 (device error)
[ 604.238473] ata1.00: status: { DRDY ERR }
[ 604.238478] ata1.00: error: { ABRT }
[ 604.248894] ahci 0000:00:17.0: port does not support device sleep
[ 604.254875] ata1.00: configured for UDMA/100
[ 604.265125] ahci 0000:00:17.0: port does not support device sleep
[ 604.265308] ata1: EH complete
[ 604.298344] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 604.298360] ata1.00: irq_stat 0x40000001
[ 604.298365] ata1: SError: { CommWake }
[ 604.298375] ata1.00: failed command: WRITE DMA EXT
[ 604.298379] ata1.00: cmd 35/00:08:88:72:af/00:00:56:00:00/e0 tag 2 dma 4096 out
res 51/04:08:88:72:af/00:00:56:00:00/e0 Emask 0x1 (device error)
[ 604.298401] ata1.00: status: { DRDY ERR }
[ 604.298406] ata1.00: error: { ABRT }
[ 604.309097] ahci 0000:00:17.0: port does not support device sleep
[ 604.315214] ata1.00: configured for UDMA/100
[ 604.325471] ahci 0000:00:17.0: port does not support device sleep
[ 604.325578] ata1: EH complete
[ 604.368341] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 604.368356] ata1.00: irq_stat 0x40000001
[ 604.368361] ata1: SError: { CommWake }
[ 604.368371] ata1.00: failed command: WRITE DMA EXT
[ 604.368375] ata1.00: cmd 35/00:08:a8:71:af/00:00:56:00:00/e0 tag 6 dma 4096 out
res 51/04:08:a8:71:af/00:00:56:00:00/e0 Emask 0x1 (device error)
[ 604.368396] ata1.00: status: { DRDY ERR }
[ 604.368401] ata1.00: error: { ABRT }
[ 604.378549] ahci 0000:00:17.0: port does not support device sleep
[ 604.383894] ata1.00: configured for UDMA/100
[ 604.394042] ahci 0000:00:17.0: port does not support device sleep
[ 604.394213] scsi_io_completion_action: 5 callbacks suppressed
[ 604.394229] sd 0:0:0:0: [sda] tag#6 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=3s
[ 604.394241] sd 0:0:0:0: [sda] tag#6 Sense Key : Illegal Request [current]
[ 604.394249] sd 0:0:0:0: [sda] tag#6 Add. Sense: Unaligned write command
[ 604.394256] sd 0:0:0:0: [sda] tag#6 CDB: Write(10) 2a 00 56 af 71 a8 00 00 08 00
[ 604.394261] blk_print_req_error: 5 callbacks suppressed
[ 604.394265] I/O error, dev sda, sector 1454338472 op 0x1:(WRITE) flags 0x800 phys_seg 1 prio class 2
[ 604.394279] buffer_io_error: 7 callbacks suppressed
[ 604.394282] Buffer I/O error on dev sda3, logical block 150994997, lost async page write
[ 604.394320] ata1: EH complete
[ 604.425065] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 604.425080] ata1.00: irq_stat 0x40000001
[ 604.425085] ata1: SError: { CommWake }
[ 604.425096] ata1.00: failed command: WRITE DMA EXT
[ 604.425101] ata1.00: cmd 35/00:08:28:7c:af/00:00:56:00:00/e0 tag 11 dma 4096 out
res 51/04:08:28:7c:af/00:00:56:00:00/e0 Emask 0x1 (device error)
[ 604.425122] ata1.00: status: { DRDY ERR }
[ 604.425127] ata1.00: error: { ABRT }
[ 604.435546] ahci 0000:00:17.0: port does not support device sleep
[ 604.441665] ata1.00: configured for UDMA/100
[ 604.451962] ahci 0000:00:17.0: port does not support device sleep
[ 604.452154] sd 0:0:0:0: [sda] tag#11 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=3s
[ 604.452167] sd 0:0:0:0: [sda] tag#11 Sense Key : Illegal Request [current]
[ 604.452175] sd 0:0:0:0: [sda] tag#11 Add. Sense: Unaligned write command
[ 604.452183] sd 0:0:0:0: [sda] tag#11 CDB: Write(10) 2a 00 56 af 7c 28 00 00 08 00
[ 604.452188] I/O error, dev sda, sector 1454341160 op 0x1:(WRITE) flags 0x800 phys_seg 1 prio class 2
[ 604.452201] Buffer I/O error on dev sda3, logical block 150995333, lost async page write
[ 604.452240] ata1: EH complete
[ 604.485011] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 604.485025] ata1.00: irq_stat 0x40000001
[ 604.485030] ata1: SError: { CommWake }
[ 604.485041] ata1.00: failed command: WRITE DMA EXT
[ 604.485045] ata1.00: cmd 35/00:08:50:70:6f/00:00:58:00:00/e0 tag 7 dma 4096 out
res 51/04:08:50:70:6f/00:00:58:00:00/e0 Emask 0x1 (device error)
[ 604.485066] ata1.00: status: { DRDY ERR }
[ 604.485071] ata1.00: error: { ABRT }
[ 604.495762] ahci 0000:00:17.0: port does not support device sleep
[ 604.501978] ata1.00: configured for UDMA/100
[ 604.512245] ahci 0000:00:17.0: port does not support device sleep
[ 604.512354] sd 0:0:0:0: [sda] tag#7 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=3s
[ 604.512366] sd 0:0:0:0: [sda] tag#7 Sense Key : Illegal Request [current]
[ 604.512373] sd 0:0:0:0: [sda] tag#7 Add. Sense: Unaligned write command
[ 604.512381] sd 0:0:0:0: [sda] tag#7 CDB: Write(10) 2a 00 58 6f 70 50 00 00 08 00
[ 604.512386] I/O error, dev sda, sector 1483698256 op 0x1:(WRITE) flags 0x800 phys_seg 1 prio class 2
[ 604.512401] Buffer I/O error on dev sda3, logical block 154664970, lost async page write
[ 604.512439] ata1: EH complete
[ 604.545061] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 604.545076] ata1.00: irq_stat 0x40000001
[ 604.545082] ata1: SError: { CommWake }
[ 604.545093] ata1.00: failed command: WRITE DMA EXT
[ 604.545098] ata1.00: cmd 35/00:08:08:70:ef/00:00:59:00:00/e0 tag 16 dma 4096 out
res 51/04:08:08:70:ef/00:00:59:00:00/e0 Emask 0x1 (device error)
[ 604.545119] ata1.00: status: { DRDY ERR }
[ 604.545124] ata1.00: error: { ABRT }
[ 604.555815] ahci 0000:00:17.0: port does not support device sleep
[ 604.561583] ata1.00: configured for UDMA/100
[ 604.571844] ahci 0000:00:17.0: port does not support device sleep
[ 604.572035] sd 0:0:0:0: [sda] tag#16 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=3s
[ 604.572047] sd 0:0:0:0: [sda] tag#16 Sense Key : Illegal Request [current]
[ 604.572056] sd 0:0:0:0: [sda] tag#16 Add. Sense: Unaligned write command
[ 604.572064] sd 0:0:0:0: [sda] tag#16 CDB: Write(10) 2a 00 59 ef 70 08 00 00 08 00
[ 604.572068] I/O error, dev sda, sector 1508864008 op 0x1:(WRITE) flags 0x800 phys_seg 1 prio class 2
[ 604.572083] Buffer I/O error on dev sda3, logical block 157810689, lost async page write
[ 604.572122] ata1: EH complete
[ 604.605008] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 604.605046] ata1.00: irq_stat 0x40000001
[ 604.605051] ata1: SError: { CommWake }
[ 604.605062] ata1.00: failed command: WRITE DMA EXT
[ 604.605067] ata1.00: cmd 35/00:08:48:70:2f/00:00:5f:00:00/e0 tag 12 dma 4096 out
res 51/04:08:48:70:2f/00:00:5f:00:00/e0 Emask 0x1 (device error)
[ 604.605088] ata1.00: status: { DRDY ERR }
[ 604.605093] ata1.00: error: { ABRT }
[ 604.615707] ahci 0000:00:17.0: port does not support device sleep
[ 604.621733] ata1.00: configured for UDMA/100
[ 604.631992] ahci 0000:00:17.0: port does not support device sleep
[ 604.632121] sd 0:0:0:0: [sda] tag#12 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=3s
[ 604.632133] sd 0:0:0:0: [sda] tag#12 Sense Key : Illegal Request [current]
[ 604.632141] sd 0:0:0:0: [sda] tag#12 Add. Sense: Unaligned write command
[ 604.632148] sd 0:0:0:0: [sda] tag#12 CDB: Write(10) 2a 00 5f 2f 70 48 00 00 08 00
[ 604.632153] I/O error, dev sda, sector 1596944456 op 0x1:(WRITE) flags 0x800 phys_seg 1 prio class 2
[ 604.632168] Buffer I/O error on dev sda3, logical block 168820745, lost async page write
[ 604.632205] ata1: EH complete
[ 604.665059] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 604.665074] ata1.00: irq_stat 0x40000001
[ 604.665079] ata1: SError: { CommWake }
[ 604.665091] ata1.00: failed command: WRITE DMA EXT
[ 604.665096] ata1.00: cmd 35/00:08:08:70:af/00:00:61:00:00/e0 tag 21 dma 4096 out
res 51/04:08:08:70:af/00:00:61:00:00/e0 Emask 0x1 (device error)
[ 604.665118] ata1.00: status: { DRDY ERR }
[ 604.665123] ata1.00: error: { ABRT }
[ 604.675816] ahci 0000:00:17.0: port does not support device sleep
[ 604.682462] ata1.00: configured for UDMA/100
[ 604.692900] ahci 0000:00:17.0: port does not support device sleep
[ 604.693114] sd 0:0:0:0: [sda] tag#21 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=3s
[ 604.693127] sd 0:0:0:0: [sda] tag#21 Sense Key : Illegal Request [current]
[ 604.693135] sd 0:0:0:0: [sda] tag#21 Add. Sense: Unaligned write command
[ 604.693143] sd 0:0:0:0: [sda] tag#21 CDB: Write(10) 2a 00 61 af 70 08 00 00 08 00
[ 604.693148] I/O error, dev sda, sector 1638887432 op 0x1:(WRITE) flags 0x800 phys_seg 1 prio class 2
[ 604.693163] Buffer I/O error on dev sda3, logical block 174063617, lost async page write
[ 604.693202] ata1: EH complete
[ 604.725010] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 604.725025] ata1.00: irq_stat 0x40000001
[ 604.725030] ata1: SError: { CommWake }
[ 604.725041] ata1.00: failed command: WRITE DMA EXT
[ 604.725046] ata1.00: cmd 35/00:08:78:70:ef/00:00:5f:00:00/e0 tag 17 dma 4096 out
res 51/04:08:78:70:ef/00:00:5f:00:00/e0 Emask 0x1 (device error)
[ 604.725068] ata1.00: status: { DRDY ERR }
[ 604.725073] ata1.00: error: { ABRT }
[ 604.735760] ahci 0000:00:17.0: port does not support device sleep
[ 604.741607] ata1.00: configured for UDMA/100
[ 604.751755] ahci 0000:00:17.0: port does not support device sleep
[ 604.751862] sd 0:0:0:0: [sda] tag#17 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=3s
[ 604.751873] sd 0:0:0:0: [sda] tag#17 Sense Key : Illegal Request [current]
[ 604.751883] sd 0:0:0:0: [sda] tag#17 Add. Sense: Unaligned write command
[ 604.751897] sd 0:0:0:0: [sda] tag#17 CDB: Write(10) 2a 00 5f ef 70 78 00 00 08 00
[ 604.751904] I/O error, dev sda, sector 1609527416 op 0x1:(WRITE) flags 0x800 phys_seg 1 prio class 2
[ 604.751919] Buffer I/O error on dev sda3, logical block 170393615, lost async page write
[ 604.751956] ata1: EH complete
[ 604.785059] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 604.785074] ata1.00: irq_stat 0x40000001
[ 604.785079] ata1: SError: { CommWake }
[ 604.785091] ata1.00: failed command: WRITE DMA EXT
[ 604.785096] ata1.00: cmd 35/00:08:78:70:ef/00:00:5c:00:00/e0 tag 26 dma 4096 out
res 51/04:08:78:70:ef/00:00:5c:00:00/e0 Emask 0x1 (device error)
[ 604.785118] ata1.00: status: { DRDY ERR }
[ 604.785123] ata1.00: error: { ABRT }
[ 604.795843] ahci 0000:00:17.0: port does not support device sleep
[ 604.802494] ata1.00: configured for UDMA/100
[ 604.812945] ahci 0000:00:17.0: port does not support device sleep
[ 604.813134] sd 0:0:0:0: [sda] tag#26 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=4s
[ 604.813147] sd 0:0:0:0: [sda] tag#26 Sense Key : Illegal Request [current]
[ 604.813156] sd 0:0:0:0: [sda] tag#26 Add. Sense: Unaligned write command
[ 604.813164] sd 0:0:0:0: [sda] tag#26 CDB: Write(10) 2a 00 5c ef 70 78 00 00 08 00
[ 604.813169] I/O error, dev sda, sector 1559195768 op 0x1:(WRITE) flags 0x800 phys_seg 1 prio class 2
[ 604.813183] Buffer I/O error on dev sda3, logical block 164102159, lost async page write
[ 604.813222] ata1: EH complete
[ 604.845010] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 604.845025] ata1.00: irq_stat 0x40000001
[ 604.845030] ata1: SError: { CommWake }
[ 604.845042] ata1.00: failed command: WRITE DMA EXT
[ 604.845046] ata1.00: cmd 35/00:10:58:70:2f/00:00:59:00:00/e0 tag 22 dma 8192 out
res 51/04:10:58:70:2f/00:00:59:00:00/e0 Emask 0x1 (device error)
[ 604.845068] ata1.00: status: { DRDY ERR }
[ 604.845073] ata1.00: error: { ABRT }
[ 604.855760] ahci 0000:00:17.0: port does not support device sleep
[ 604.861628] ata1.00: configured for UDMA/100
[ 604.871782] ahci 0000:00:17.0: port does not support device sleep
[ 604.871961] sd 0:0:0:0: [sda] tag#22 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=4s
[ 604.871975] sd 0:0:0:0: [sda] tag#22 Sense Key : Illegal Request [current]
[ 604.871983] sd 0:0:0:0: [sda] tag#22 Add. Sense: Unaligned write command
[ 604.871991] sd 0:0:0:0: [sda] tag#22 CDB: Write(10) 2a 00 59 2f 70 58 00 00 10 00
[ 604.871996] I/O error, dev sda, sector 1496281176 op 0x1:(WRITE) flags 0x800 phys_seg 2 prio class 2
[ 604.872010] Buffer I/O error on dev sda3, logical block 156237835, lost async page write
[ 604.872030] Buffer I/O error on dev sda3, logical block 156237836, lost async page write
[ 604.872056] ata1: EH complete
[ 604.905077] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 604.905093] ata1.00: irq_stat 0x40000001
[ 604.905097] ata1: SError: { CommWake }
[ 604.905107] ata1.00: failed command: WRITE DMA EXT
[ 604.905112] ata1.00: cmd 35/00:10:d0:7d:b0/00:00:56:00:00/e0 tag 1 dma 8192 out
res 51/04:10:d0:7d:b0/00:00:56:00:00/e0 Emask 0x1 (device error)
[ 604.905133] ata1.00: status: { DRDY ERR }
[ 604.905138] ata1.00: error: { ABRT }
[ 604.915851] ahci 0000:00:17.0: port does not support device sleep
[ 604.922450] ata1.00: configured for UDMA/100
[ 604.932887] ahci 0000:00:17.0: port does not support device sleep
[ 604.933074] sd 0:0:0:0: [sda] tag#1 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=4s
[ 604.933087] sd 0:0:0:0: [sda] tag#1 Sense Key : Illegal Request [current]
[ 604.933096] sd 0:0:0:0: [sda] tag#1 Add. Sense: Unaligned write command
[ 604.933103] sd 0:0:0:0: [sda] tag#1 CDB: Write(10) 2a 00 56 b0 7d d0 00 00 10 00
[ 604.933109] I/O error, dev sda, sector 1454407120 op 0x1:(WRITE) flags 0x800 phys_seg 2 prio class 2
[ 604.933159] ata1: EH complete
[ 604.965016] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 604.965033] ata1.00: irq_stat 0x40000001
[ 604.965040] ata1: SError: { CommWake }
[ 604.965054] ata1.00: failed command: WRITE DMA EXT
[ 604.965060] ata1.00: cmd 35/00:08:00:71:af/00:00:56:00:00/e0 tag 5 dma 4096 out
res 51/04:08:00:71:af/00:00:56:00:00/e0 Emask 0x1 (device error)
[ 604.965084] ata1.00: status: { DRDY ERR }
[ 604.965089] ata1.00: error: { ABRT }
[ 604.975788] ahci 0000:00:17.0: port does not support device sleep
[ 604.981240] ata1.00: configured for UDMA/100
[ 604.991656] ahci 0000:00:17.0: port does not support device sleep
[ 604.991788] ata1: EH complete
[ 605.025005] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 605.025020] ata1.00: irq_stat 0x40000001
[ 605.025025] ata1: SError: { CommWake }
[ 605.025036] ata1.00: failed command: WRITE DMA EXT
[ 605.025040] ata1.00: cmd 35/00:08:88:72:af/00:00:56:00:00/e0 tag 7 dma 4096 out
res 51/04:08:88:72:af/00:00:56:00:00/e0 Emask 0x1 (device error)
[ 605.025062] ata1.00: status: { DRDY ERR }
[ 605.025067] ata1.00: error: { ABRT }
[ 605.035686] ahci 0000:00:17.0: port does not support device sleep
[ 605.041924] ata1.00: configured for UDMA/100
[ 605.052472] ahci 0000:00:17.0: port does not support device sleep
[ 605.052601] ata1: EH complete
[ 605.098355] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 605.098370] ata1.00: irq_stat 0x40000001
[ 605.098375] ata1: SError: { CommWake }
[ 605.098387] ata1.00: failed command: WRITE DMA EXT
[ 605.098391] ata1.00: cmd 35/00:08:38:70:6f/00:00:67:00:00/e0 tag 15 dma 4096 out
res 51/04:08:38:70:6f/00:00:67:00:00/e0 Emask 0x1 (device error)
[ 605.098413] ata1.00: status: { DRDY ERR }
[ 605.098418] ata1.00: error: { ABRT }
[ 605.109036] ahci 0000:00:17.0: port does not support device sleep
[ 605.115339] ata1.00: configured for UDMA/100
[ 605.125889] ahci 0000:00:17.0: port does not support device sleep
[ 605.125994] ata1: EH complete
[ 605.158333] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 605.158348] ata1.00: irq_stat 0x40000001
[ 605.158353] ata1: SError: { CommWake }
[ 605.158364] ata1.00: failed command: WRITE DMA EXT
[ 605.158368] ata1.00: cmd 35/00:08:38:70:6f/00:00:67:00:00/e0 tag 9 dma 4096 out
res 51/04:08:38:70:6f/00:00:67:00:00/e0 Emask 0x1 (device error)
[ 605.158390] ata1.00: status: { DRDY ERR }
[ 605.158395] ata1.00: error: { ABRT }
[ 605.168572] ahci 0000:00:17.0: port does not support device sleep
[ 605.174520] ata1.00: configured for UDMA/100
[ 605.184995] ahci 0000:00:17.0: port does not support device sleep
[ 605.185100] ata1: EH complete
[ 605.218340] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 605.218355] ata1.00: irq_stat 0x40000001
[ 605.218360] ata1: SError: { CommWake }
[ 605.218371] ata1.00: failed command: WRITE DMA EXT
[ 605.218375] ata1.00: cmd 35/00:08:38:70:6f/00:00:67:00:00/e0 tag 11 dma 4096 out
res 51/04:08:38:70:6f/00:00:67:00:00/e0 Emask 0x1 (device error)
[ 605.218397] ata1.00: status: { DRDY ERR }
[ 605.218402] ata1.00: error: { ABRT }
[ 605.229011] ahci 0000:00:17.0: port does not support device sleep
[ 605.235030] ata1.00: configured for UDMA/100
[ 605.245581] ahci 0000:00:17.0: port does not support device sleep
[ 605.245684] ata1: EH complete
[ 605.278333] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 605.278348] ata1.00: irq_stat 0x40000001
[ 605.278354] ata1: SError: { CommWake }
[ 605.278365] ata1.00: failed command: WRITE DMA EXT
[ 605.278369] ata1.00: cmd 35/00:08:38:70:6f/00:00:67:00:00/e0 tag 13 dma 4096 out
res 51/04:08:38:70:6f/00:00:67:00:00/e0 Emask 0x1 (device error)
[ 605.278391] ata1.00: status: { DRDY ERR }
[ 605.278396] ata1.00: error: { ABRT }
[ 605.288619] ahci 0000:00:17.0: port does not support device sleep
[ 605.294840] ata1.00: configured for UDMA/100
[ 605.305392] ahci 0000:00:17.0: port does not support device sleep
[ 605.305503] ata1: EH complete
[ 605.338334] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 605.338350] ata1.00: irq_stat 0x40000001
[ 605.338356] ata1: SError: { CommWake }
[ 605.338380] ata1.00: failed command: WRITE DMA EXT
[ 605.338384] ata1.00: cmd 35/00:08:38:70:6f/00:00:67:00:00/e0 tag 15 dma 4096 out
res 51/04:08:38:70:6f/00:00:67:00:00/e0 Emask 0x1 (device error)
[ 605.338406] ata1.00: status: { DRDY ERR }
[ 605.338411] ata1.00: error: { ABRT }
[ 605.349021] ahci 0000:00:17.0: port does not support device sleep
[ 605.355225] ata1.00: configured for UDMA/100
[ 605.365774] ahci 0000:00:17.0: port does not support device sleep
[ 605.365883] ata1: EH complete
[ 605.398330] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 605.398345] ata1.00: irq_stat 0x40000001
[ 605.398350] ata1: SError: { CommWake }
[ 605.398361] ata1.00: failed command: WRITE DMA EXT
[ 605.398366] ata1.00: cmd 35/00:08:38:70:6f/00:00:67:00:00/e0 tag 17 dma 4096 out
res 51/04:08:38:70:6f/00:00:67:00:00/e0 Emask 0x1 (device error)
[ 605.398388] ata1.00: status: { DRDY ERR }
[ 605.398393] ata1.00: error: { ABRT }
[ 605.409002] ahci 0000:00:17.0: port does not support device sleep
[ 605.415431] ata1.00: configured for UDMA/100
[ 605.425734] ahci 0000:00:17.0: port does not support device sleep
[ 605.425868] ata1: EH complete
[ 605.471738] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 605.471752] ata1.00: irq_stat 0x40000001
[ 605.471757] ata1: SError: { CommWake }
[ 605.471769] ata1.00: failed command: WRITE DMA EXT
[ 605.471774] ata1.00: cmd 35/00:08:38:70:af/00:00:67:00:00/e0 tag 18 dma 4096 out
res 51/04:08:38:70:af/00:00:67:00:00/e0 Emask 0x1 (device error)
[ 605.471795] ata1.00: status: { DRDY ERR }
[ 605.471800] ata1.00: error: { ABRT }
[ 605.482416] ahci 0000:00:17.0: port does not support device sleep
[ 605.488643] ata1.00: configured for UDMA/100
[ 605.498774] ahci 0000:00:17.0: port does not support device sleep
[ 605.498984] ata1: EH complete
[ 605.545008] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 605.545023] ata1.00: irq_stat 0x40000001
[ 605.545028] ata1: SError: { CommWake }
[ 605.545039] ata1.00: failed command: WRITE DMA EXT
[ 605.545044] ata1.00: cmd 35/00:08:20:70:ef/00:00:6d:00:00/e0 tag 17 dma 4096 out
res 51/04:08:20:70:ef/00:00:6d:00:00/e0 Emask 0x1 (device error)
[ 605.545065] ata1.00: status: { DRDY ERR }
[ 605.545071] ata1.00: error: { ABRT }
[ 605.555693] ahci 0000:00:17.0: port does not support device sleep
[ 605.561903] ata1.00: configured for UDMA/100
[ 605.572163] ahci 0000:00:17.0: port does not support device sleep
[ 605.572276] ata1: EH complete
[ 605.618344] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 605.618359] ata1.00: irq_stat 0x40000001
[ 605.618364] ata1: SError: { CommWake }
[ 605.618375] ata1.00: failed command: WRITE DMA EXT
[ 605.618379] ata1.00: cmd 35/00:08:00:70:6f/00:00:72:00:00/e0 tag 10 dma 4096 out
res 51/04:08:00:70:6f/00:00:72:00:00/e0 Emask 0x1 (device error)
[ 605.618401] ata1.00: status: { DRDY ERR }
[ 605.618407] ata1.00: error: { ABRT }
[ 605.629029] ahci 0000:00:17.0: port does not support device sleep
[ 605.635435] ata1.00: configured for UDMA/100
[ 605.645737] ahci 0000:00:17.0: port does not support device sleep
[ 605.645854] ata1: EH complete
[ 605.691679] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 605.691694] ata1.00: irq_stat 0x40000001
[ 605.691700] ata1: SError: { CommWake }
[ 605.691712] ata1.00: failed command: WRITE DMA EXT
[ 605.691717] ata1.00: cmd 35/00:08:70:70:2f/00:00:6d:00:00/e0 tag 20 dma 4096 out
res 51/04:08:70:70:2f/00:00:6d:00:00/e0 Emask 0x1 (device error)
[ 605.691738] ata1.00: status: { DRDY ERR }
[ 605.691743] ata1.00: error: { ABRT }
[ 605.702060] ahci 0000:00:17.0: port does not support device sleep
[ 605.708612] ata1.00: configured for UDMA/100
[ 605.718878] ahci 0000:00:17.0: port does not support device sleep
[ 605.718995] ata1: EH complete
[ 605.765005] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 605.765020] ata1.00: irq_stat 0x40000001
[ 605.765026] ata1: SError: { CommWake }
[ 605.765038] ata1.00: failed command: WRITE DMA EXT
[ 605.765043] ata1.00: cmd 35/00:08:08:70:ef/00:00:6d:00:00/e0 tag 26 dma 4096 out
res 51/04:08:08:70:ef/00:00:6d:00:00/e0 Emask 0x1 (device error)
[ 605.765064] ata1.00: status: { DRDY ERR }
[ 605.765069] ata1.00: error: { ABRT }
[ 605.775767] ahci 0000:00:17.0: port does not support device sleep
[ 605.781765] ata1.00: configured for UDMA/100
[ 605.791999] ahci 0000:00:17.0: port does not support device sleep
[ 605.792116] ata1: EH complete
[ 605.825014] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 605.825028] ata1.00: irq_stat 0x40000001
[ 605.825033] ata1: SError: { CommWake }
[ 605.825042] ata1.00: failed command: WRITE DMA EXT
[ 605.825047] ata1.00: cmd 35/00:08:38:70:af/00:00:67:00:00/e0 tag 1 dma 4096 out
res 51/04:08:38:70:af/00:00:67:00:00/e0 Emask 0x1 (device error)
[ 605.825067] ata1.00: status: { DRDY ERR }
[ 605.825073] ata1.00: error: { ABRT }
[ 605.835775] ahci 0000:00:17.0: port does not support device sleep
[ 605.842002] ata1.00: configured for UDMA/100
[ 605.852283] ahci 0000:00:17.0: port does not support device sleep
[ 605.852400] ata1: EH complete
[ 605.885010] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 605.885025] ata1.00: irq_stat 0x40000001
[ 605.885029] ata1: SError: { CommWake }
[ 605.885040] ata1.00: failed command: WRITE DMA EXT
[ 605.885044] ata1.00: cmd 35/00:08:20:70:ef/00:00:6d:00:00/e0 tag 7 dma 4096 out
res 51/04:08:20:70:ef/00:00:6d:00:00/e0 Emask 0x1 (device error)
[ 605.885066] ata1.00: status: { DRDY ERR }
[ 605.885071] ata1.00: error: { ABRT }
[ 605.895493] ahci 0000:00:17.0: port does not support device sleep
[ 605.901652] ata1.00: configured for UDMA/100
[ 605.911816] ahci 0000:00:17.0: port does not support device sleep
[ 605.911925] ata1: EH complete
[ 605.945010] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 605.945026] ata1.00: irq_stat 0x40000001
[ 605.945031] ata1: SError: { CommWake }
[ 605.945042] ata1.00: failed command: WRITE DMA EXT
[ 605.945046] ata1.00: cmd 35/00:08:00:70:6f/00:00:72:00:00/e0 tag 13 dma 4096 out
res 51/04:08:00:70:6f/00:00:72:00:00/e0 Emask 0x1 (device error)
[ 605.945068] ata1.00: status: { DRDY ERR }
[ 605.945073] ata1.00: error: { ABRT }
[ 605.955770] ahci 0000:00:17.0: port does not support device sleep
[ 605.962151] ata1.00: configured for UDMA/100
[ 605.972460] ahci 0000:00:17.0: port does not support device sleep
[ 605.972577] ata1: EH complete
[ 606.005009] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 606.005033] ata1.00: irq_stat 0x40000001
[ 606.005039] ata1: SError: { CommWake }
[ 606.005058] ata1.00: failed command: WRITE DMA EXT
[ 606.005063] ata1.00: cmd 35/00:08:70:70:2f/00:00:6d:00:00/e0 tag 19 dma 4096 out
res 51/04:08:70:70:2f/00:00:6d:00:00/e0 Emask 0x1 (device error)
[ 606.005084] ata1.00: status: { DRDY ERR }
[ 606.005090] ata1.00: error: { ABRT }
[ 606.015783] ahci 0000:00:17.0: port does not support device sleep
[ 606.022158] ata1.00: configured for UDMA/100
[ 606.032467] ahci 0000:00:17.0: port does not support device sleep
[ 606.032583] ata1: EH complete
[ 606.065006] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 606.065021] ata1.00: irq_stat 0x40000001
[ 606.065026] ata1: SError: { CommWake }
[ 606.065035] ata1.00: failed command: WRITE DMA EXT
[ 606.065040] ata1.00: cmd 35/00:08:08:70:ef/00:00:6d:00:00/e0 tag 0 dma 4096 out
res 51/04:08:08:70:ef/00:00:6d:00:00/e0 Emask 0x1 (device error)
[ 606.065061] ata1.00: status: { DRDY ERR }
[ 606.065067] ata1.00: error: { ABRT }
[ 606.075766] ahci 0000:00:17.0: port does not support device sleep
[ 606.081978] ata1.00: configured for UDMA/100
[ 606.092252] ahci 0000:00:17.0: port does not support device sleep
[ 606.092366] ata1: EH complete
[ 606.125009] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 606.125024] ata1.00: irq_stat 0x40000001
[ 606.125029] ata1: SError: { CommWake }
[ 606.125039] ata1.00: failed command: WRITE DMA EXT
[ 606.125044] ata1.00: cmd 35/00:08:38:70:af/00:00:67:00:00/e0 tag 6 dma 4096 out
res 51/04:08:38:70:af/00:00:67:00:00/e0 Emask 0x1 (device error)
[ 606.125065] ata1.00: status: { DRDY ERR }
[ 606.125070] ata1.00: error: { ABRT }
[ 606.135766] ahci 0000:00:17.0: port does not support device sleep
[ 606.141929] ata1.00: configured for UDMA/100
[ 606.152189] ahci 0000:00:17.0: port does not support device sleep
[ 606.152307] ata1: EH complete
[ 606.185010] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 606.185024] ata1.00: irq_stat 0x40000001
[ 606.185029] ata1: SError: { CommWake }
[ 606.185041] ata1.00: failed command: WRITE DMA EXT
[ 606.185045] ata1.00: cmd 35/00:08:20:70:ef/00:00:6d:00:00/e0 tag 12 dma 4096 out
res 51/04:08:20:70:ef/00:00:6d:00:00/e0 Emask 0x1 (device error)
[ 606.185066] ata1.00: status: { DRDY ERR }
[ 606.185071] ata1.00: error: { ABRT }
[ 606.195767] ahci 0000:00:17.0: port does not support device sleep
[ 606.202027] ata1.00: configured for UDMA/100
[ 606.212306] ahci 0000:00:17.0: port does not support device sleep
[ 606.212424] ata1: EH complete
[ 606.245011] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 606.245026] ata1.00: irq_stat 0x40000001
[ 606.245031] ata1: SError: { CommWake }
[ 606.245042] ata1.00: failed command: WRITE DMA EXT
[ 606.245047] ata1.00: cmd 35/00:08:00:70:6f/00:00:72:00:00/e0 tag 18 dma 4096 out
res 51/04:08:00:70:6f/00:00:72:00:00/e0 Emask 0x1 (device error)
[ 606.245069] ata1.00: status: { DRDY ERR }
[ 606.245074] ata1.00: error: { ABRT }
[ 606.255771] ahci 0000:00:17.0: port does not support device sleep
[ 606.262029] ata1.00: configured for UDMA/100
[ 606.272318] ahci 0000:00:17.0: port does not support device sleep
[ 606.272434] ata1: EH complete
[ 606.305010] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 606.305032] ata1.00: irq_stat 0x40000001
[ 606.305040] ata1: SError: { CommWake }
[ 606.305056] ata1.00: failed command: WRITE DMA EXT
[ 606.305060] ata1.00: cmd 35/00:08:70:70:2f/00:00:6d:00:00/e0 tag 24 dma 4096 out
res 51/04:08:70:70:2f/00:00:6d:00:00/e0 Emask 0x1 (device error)
[ 606.305081] ata1.00: status: { DRDY ERR }
[ 606.305087] ata1.00: error: { ABRT }
[ 606.315783] ahci 0000:00:17.0: port does not support device sleep
[ 606.321917] ata1.00: configured for UDMA/100
[ 606.332180] ahci 0000:00:17.0: port does not support device sleep
[ 606.332297] ata1: EH complete
[ 606.365011] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 606.365026] ata1.00: irq_stat 0x40000001
[ 606.365031] ata1: SError: { CommWake }
[ 606.365044] ata1.00: failed command: WRITE DMA EXT
[ 606.365048] ata1.00: cmd 35/00:08:08:70:ef/00:00:6d:00:00/e0 tag 30 dma 4096 out
res 51/04:08:08:70:ef/00:00:6d:00:00/e0 Emask 0x1 (device error)
[ 606.365069] ata1.00: status: { DRDY ERR }
[ 606.365074] ata1.00: error: { ABRT }
[ 606.375688] ahci 0000:00:17.0: port does not support device sleep
[ 606.382033] ata1.00: configured for UDMA/100
[ 606.392319] ahci 0000:00:17.0: port does not support device sleep
[ 606.392436] ata1: EH complete
[ 606.425023] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 606.425037] ata1.00: irq_stat 0x40000001
[ 606.425042] ata1: SError: { CommWake }
[ 606.425051] ata1.00: failed command: WRITE DMA EXT
[ 606.425056] ata1.00: cmd 35/00:08:38:70:af/00:00:67:00:00/e0 tag 5 dma 4096 out
res 51/04:08:38:70:af/00:00:67:00:00/e0 Emask 0x1 (device error)
[ 606.425077] ata1.00: status: { DRDY ERR }
[ 606.425082] ata1.00: error: { ABRT }
[ 606.435788] ahci 0000:00:17.0: port does not support device sleep
[ 606.442007] ata1.00: configured for UDMA/100
[ 606.452287] ahci 0000:00:17.0: port does not support device sleep
[ 606.452403] ata1: EH complete
[ 606.485009] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 606.485023] ata1.00: irq_stat 0x40000001
[ 606.485028] ata1: SError: { CommWake }
[ 606.485039] ata1.00: failed command: WRITE DMA EXT
[ 606.485044] ata1.00: cmd 35/00:08:20:70:ef/00:00:6d:00:00/e0 tag 11 dma 4096 out
res 51/04:08:20:70:ef/00:00:6d:00:00/e0 Emask 0x1 (device error)
[ 606.485065] ata1.00: status: { DRDY ERR }
[ 606.485070] ata1.00: error: { ABRT }
[ 606.495769] ahci 0000:00:17.0: port does not support device sleep
[ 606.501988] ata1.00: configured for UDMA/100
[ 606.512265] ahci 0000:00:17.0: port does not support device sleep
[ 606.512377] ata1: EH complete
[ 606.545019] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 606.545033] ata1.00: irq_stat 0x40000001
[ 606.545038] ata1: SError: { CommWake }
[ 606.545050] ata1.00: failed command: WRITE DMA EXT
[ 606.545054] ata1.00: cmd 35/00:08:00:70:6f/00:00:72:00:00/e0 tag 17 dma 4096 out
res 51/04:08:00:70:6f/00:00:72:00:00/e0 Emask 0x1 (device error)
[ 606.545075] ata1.00: status: { DRDY ERR }
[ 606.545081] ata1.00: error: { ABRT }
[ 606.555780] ahci 0000:00:17.0: port does not support device sleep
[ 606.561795] ata1.00: configured for UDMA/100
[ 606.572040] ahci 0000:00:17.0: port does not support device sleep
[ 606.572156] ata1: EH complete
[ 606.605013] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 606.605034] ata1.00: irq_stat 0x40000001
[ 606.605042] ata1: SError: { CommWake }
[ 606.605059] ata1.00: failed command: WRITE DMA EXT
[ 606.605064] ata1.00: cmd 35/00:08:70:70:2f/00:00:6d:00:00/e0 tag 23 dma 4096 out
res 51/04:08:70:70:2f/00:00:6d:00:00/e0 Emask 0x1 (device error)
[ 606.605085] ata1.00: status: { DRDY ERR }
[ 606.605091] ata1.00: error: { ABRT }
[ 606.615504] ahci 0000:00:17.0: port does not support device sleep
[ 606.621771] ata1.00: configured for UDMA/100
[ 606.632000] ahci 0000:00:17.0: port does not support device sleep
[ 606.632131] ata1: EH complete
[ 606.665014] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 606.665029] ata1.00: irq_stat 0x40000001
[ 606.665034] ata1: SError: { CommWake }
[ 606.665044] ata1.00: failed command: WRITE DMA EXT
[ 606.665048] ata1.00: cmd 35/00:08:08:70:ef/00:00:6d:00:00/e0 tag 4 dma 4096 out
res 51/04:08:08:70:ef/00:00:6d:00:00/e0 Emask 0x1 (device error)
[ 606.665069] ata1.00: status: { DRDY ERR }
[ 606.665074] ata1.00: error: { ABRT }
[ 606.675773] ahci 0000:00:17.0: port does not support device sleep
[ 606.682184] ata1.00: configured for UDMA/100
[ 606.692500] ahci 0000:00:17.0: port does not support device sleep
[ 606.692616] ata1: EH complete
[ 606.725008] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 606.725023] ata1.00: irq_stat 0x40000001
[ 606.725028] ata1: SError: { CommWake }
[ 606.725039] ata1.00: failed command: WRITE DMA EXT
[ 606.725043] ata1.00: cmd 35/00:08:38:70:af/00:00:67:00:00/e0 tag 10 dma 4096 out
res 51/04:08:38:70:af/00:00:67:00:00/e0 Emask 0x1 (device error)
[ 606.725064] ata1.00: status: { DRDY ERR }
[ 606.725069] ata1.00: error: { ABRT }
[ 606.735483] ahci 0000:00:17.0: port does not support device sleep
[ 606.741667] ata1.00: configured for UDMA/100
[ 606.751823] ahci 0000:00:17.0: port does not support device sleep
[ 606.751949] ata1: EH complete
[ 606.785014] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 606.785030] ata1.00: irq_stat 0x40000001
[ 606.785035] ata1: SError: { CommWake }
[ 606.785046] ata1.00: failed command: WRITE DMA EXT
[ 606.785050] ata1.00: cmd 35/00:08:20:70:ef/00:00:6d:00:00/e0 tag 16 dma 4096 out
res 51/04:08:20:70:ef/00:00:6d:00:00/e0 Emask 0x1 (device error)
[ 606.785072] ata1.00: status: { DRDY ERR }
[ 606.785078] ata1.00: error: { ABRT }
[ 606.795469] ahci 0000:00:17.0: port does not support device sleep
[ 606.801629] ata1.00: configured for UDMA/100
[ 606.811776] ahci 0000:00:17.0: port does not support device sleep
[ 606.811886] ata1: EH complete
[ 606.845011] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 606.845025] ata1.00: irq_stat 0x40000001
[ 606.845030] ata1: SError: { CommWake }
[ 606.845042] ata1.00: failed command: WRITE DMA EXT
[ 606.845047] ata1.00: cmd 35/00:08:00:70:6f/00:00:72:00:00/e0 tag 22 dma 4096 out
res 51/04:08:00:70:6f/00:00:72:00:00/e0 Emask 0x1 (device error)
[ 606.845068] ata1.00: status: { DRDY ERR }
[ 606.845074] ata1.00: error: { ABRT }
[ 606.855770] ahci 0000:00:17.0: port does not support device sleep
[ 606.861938] ata1.00: configured for UDMA/100
[ 606.872202] ahci 0000:00:17.0: port does not support device sleep
[ 606.872319] ata1: EH complete
[ 606.905060] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 606.905075] ata1.00: irq_stat 0x40000001
[ 606.905080] ata1: SError: { CommWake }
[ 606.905093] ata1.00: failed command: WRITE DMA EXT
[ 606.905097] ata1.00: cmd 35/00:08:70:70:2f/00:00:6d:00:00/e0 tag 27 dma 4096 out
res 51/04:08:70:70:2f/00:00:6d:00:00/e0 Emask 0x1 (device error)
[ 606.905118] ata1.00: status: { DRDY ERR }
[ 606.905124] ata1.00: error: { ABRT }
[ 606.915328] ahci 0000:00:17.0: port does not support device sleep
[ 606.921349] ata1.00: configured for UDMA/100
[ 606.931677] ahci 0000:00:17.0: port does not support device sleep
[ 606.931787] ata1: EH complete
[ 606.965037] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 606.965052] ata1.00: irq_stat 0x40000001
[ 606.965057] ata1: SError: { CommWake }
[ 606.965067] ata1.00: failed command: WRITE DMA EXT
[ 606.965071] ata1.00: cmd 35/00:08:08:70:ef/00:00:6d:00:00/e0 tag 1 dma 4096 out
res 51/04:08:08:70:ef/00:00:6d:00:00/e0 Emask 0x1 (device error)
[ 606.965092] ata1.00: status: { DRDY ERR }
[ 606.965098] ata1.00: error: { ABRT }
[ 606.975316] ahci 0000:00:17.0: port does not support device sleep
[ 606.981249] ata1.00: configured for UDMA/100
[ 606.991669] ahci 0000:00:17.0: port does not support device sleep
[ 606.991767] ata1: EH complete
[ 607.028352] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 607.028367] ata1.00: irq_stat 0x40000001
[ 607.028372] ata1: SError: { CommWake }
[ 607.028382] ata1.00: failed command: WRITE DMA EXT
[ 607.028387] ata1.00: cmd 35/00:08:38:70:af/00:00:67:00:00/e0 tag 6 dma 4096 out
res 51/04:08:38:70:af/00:00:67:00:00/e0 Emask 0x1 (device error)
[ 607.028408] ata1.00: status: { DRDY ERR }
[ 607.028414] ata1.00: error: { ABRT }
[ 607.038686] ahci 0000:00:17.0: port does not support device sleep
[ 607.044432] ata1.00: configured for UDMA/100
[ 607.054983] ahci 0000:00:17.0: port does not support device sleep
[ 607.055144] ata1: EH complete
[ 607.088381] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 607.088403] ata1.00: irq_stat 0x40000001
[ 607.088408] ata1: SError: { CommWake }
[ 607.088419] ata1.00: failed command: WRITE DMA EXT
[ 607.088424] ata1.00: cmd 35/00:08:20:70:ef/00:00:6d:00:00/e0 tag 11 dma 4096 out
res 51/04:08:20:70:ef/00:00:6d:00:00/e0 Emask 0x1 (device error)
[ 607.088445] ata1.00: status: { DRDY ERR }
[ 607.088450] ata1.00: error: { ABRT }
[ 607.098656] ahci 0000:00:17.0: port does not support device sleep
[ 607.104558] ata1.00: configured for UDMA/100
[ 607.115010] ahci 0000:00:17.0: port does not support device sleep
[ 607.115151] ata1: EH complete
[ 607.148342] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 607.148362] ata1.00: irq_stat 0x40000001
[ 607.148367] ata1: SError: { CommWake }
[ 607.148378] ata1.00: failed command: WRITE DMA EXT
[ 607.148383] ata1.00: cmd 35/00:08:00:70:6f/00:00:72:00:00/e0 tag 16 dma 4096 out
res 51/04:08:00:70:6f/00:00:72:00:00/e0 Emask 0x1 (device error)
[ 607.148405] ata1.00: status: { DRDY ERR }
[ 607.148410] ata1.00: error: { ABRT }
[ 607.159092] ahci 0000:00:17.0: port does not support device sleep
[ 607.165223] ata1.00: configured for UDMA/100
[ 607.175477] ahci 0000:00:17.0: port does not support device sleep
[ 607.175614] ata1: EH complete
[ 607.208391] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 607.208406] ata1.00: irq_stat 0x40000001
[ 607.208410] ata1: SError: { CommWake }
[ 607.208423] ata1.00: failed command: WRITE DMA EXT
[ 607.208427] ata1.00: cmd 35/00:08:70:70:2f/00:00:6d:00:00/e0 tag 21 dma 4096 out
res 51/04:08:70:70:2f/00:00:6d:00:00/e0 Emask 0x1 (device error)
[ 607.208449] ata1.00: status: { DRDY ERR }
[ 607.208454] ata1.00: error: { ABRT }
[ 607.219147] ahci 0000:00:17.0: port does not support device sleep
[ 607.225998] ata1.00: configured for UDMA/100
[ 607.236419] ahci 0000:00:17.0: port does not support device sleep
[ 607.236639] ata1: EH complete
[ 607.268391] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 607.268406] ata1.00: irq_stat 0x40000001
[ 607.268411] ata1: SError: { CommWake }
[ 607.268424] ata1.00: failed command: WRITE DMA EXT
[ 607.268429] ata1.00: cmd 35/00:08:08:70:ef/00:00:6d:00:00/e0 tag 31 dma 4096 out
res 51/04:08:08:70:ef/00:00:6d:00:00/e0 Emask 0x1 (device error)
[ 607.268450] ata1.00: status: { DRDY ERR }
[ 607.268455] ata1.00: error: { ABRT }
[ 607.279145] ahci 0000:00:17.0: port does not support device sleep
[ 607.286060] ata1.00: configured for UDMA/100
[ 607.296608] ahci 0000:00:17.0: port does not support device sleep
[ 607.296905] ata1: EH complete
[ 607.297170] JBD2: recovery failed
[ 607.297179] EXT4-fs (sda3): error loading journal
[ 607.377413] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 607.377928] ISO 9660 Extensions: RRIP_1991A
[ 607.411111] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 607.411697] ISO 9660 Extensions: RRIP_1991A
[ 607.435654] loop0: detected capacity change from 0 to 137008
[ 607.491609] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 607.501184] loop1: detected capacity change from 0 to 2430384
[ 607.545220] loop2: detected capacity change from 0 to 3513408
[ 607.587746] loop3: detected capacity change from 0 to 1904416
[ 607.665420] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off.
[ 608.100048] systemd[1]: systemd 252.9-1-manjaro running in system mode (+PAM +AUDIT -SELINUX -APPARMOR -IMA +SMACK +SECCOMP +GCRYPT +GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY +P11KIT -QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD +BPF_FRAMEWORK +XKBCOMMON +UTMP -SYSVINIT default-hierarchy=unified)
[ 608.100058] systemd[1]: Detected architecture x86-64.
[ 608.104483] systemd[1]: Hostname set to <manjaro>.
[ 608.541810] systemd[1]: bpf-lsm: LSM BPF program attached
[ 608.945692] systemd[1]: Queued start job for default target Graphical Interface.
[ 608.967102] systemd[1]: Created slice Slice /system/getty.
[ 608.968072] systemd[1]: Created slice Slice /system/modprobe.
[ 608.968751] systemd[1]: Created slice User and Session Slice.
[ 608.969083] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 608.969610] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 608.969833] systemd[1]: Reached target Login Prompts.
[ 608.970004] systemd[1]: Reached target Local Integrity Protected Volumes.
[ 608.970202] systemd[1]: Reached target Remote File Systems.
[ 608.970368] systemd[1]: Reached target Slice Units.
[ 608.970546] systemd[1]: Reached target Swaps.
[ 608.970718] systemd[1]: Reached target Local Verity Protected Volumes.
[ 608.971039] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ 608.972769] systemd[1]: Listening on LVM2 poll daemon socket.
[ 608.975793] systemd[1]: Listening on Process Core Dump Socket.
[ 608.976371] systemd[1]: Listening on Journal Audit Socket.
[ 608.976808] systemd[1]: Listening on Journal Socket (/dev/log).
[ 608.977240] systemd[1]: Listening on Journal Socket.
[ 608.979428] systemd[1]: Listening on udev Control Socket.
[ 608.979821] systemd[1]: Listening on udev Kernel Socket.
[ 608.981920] systemd[1]: Mounting Huge Pages File System...
[ 608.983445] systemd[1]: Mounting POSIX Message Queue File System...
[ 608.985067] systemd[1]: Mounting Kernel Debug File System...
[ 608.986693] systemd[1]: Mounting Kernel Trace File System...
[ 608.989114] systemd[1]: Mounting Temporary Directory /tmp...
[ 608.991061] systemd[1]: Starting Create List of Static Device Nodes...
[ 608.992217] systemd[1]: Starting Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling...
[ 608.993409] systemd[1]: Starting Load Kernel Module configfs...
[ 608.994656] systemd[1]: Starting Load Kernel Module dm_mod...
[ 608.996595] systemd[1]: Starting Load Kernel Module drm...
[ 608.997977] systemd[1]: Starting Load Kernel Module fuse...
[ 608.999176] systemd[1]: Starting Load Kernel Module loop...
[ 609.002175] systemd[1]: Starting Load Kernel Modules...
[ 609.003048] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 609.004036] systemd[1]: Starting Coldplug All udev Devices...
[ 609.006434] systemd[1]: Mounted Huge Pages File System.
[ 609.006618] systemd[1]: Mounted POSIX Message Queue File System.
[ 609.006766] systemd[1]: Mounted Kernel Debug File System.
[ 609.006908] systemd[1]: Mounted Kernel Trace File System.
[ 609.007049] systemd[1]: Mounted Temporary Directory /tmp.
[ 609.013070] fuse: init (API version 7.37)
[ 609.041399] systemd[1]: Finished Create List of Static Device Nodes.
[ 609.042571] systemd[1]: modprobe@configfs.service: Deactivated successfully.
[ 609.061438] systemd[1]: Finished Load Kernel Module configfs.
[ 609.061799] systemd[1]: modprobe@dm_mod.service: Deactivated successfully.
[ 609.081423] systemd[1]: Finished Load Kernel Module dm_mod.
[ 609.081735] systemd[1]: modprobe@drm.service: Deactivated successfully.
[ 609.101413] systemd[1]: Finished Load Kernel Module drm.
[ 609.101728] systemd[1]: modprobe@fuse.service: Deactivated successfully.
[ 609.124669] systemd[1]: Finished Load Kernel Module fuse.
[ 609.142025] systemd[1]: Finished Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling.
[ 609.142629] systemd[1]: modprobe@loop.service: Deactivated successfully.
[ 609.171974] systemd[1]: Finished Load Kernel Module loop.
[ 609.205547] systemd[1]: Finished Load Kernel Modules.
[ 609.235171] systemd[1]: Finished Remount Root and Kernel File Systems.
[ 609.282207] systemd[1]: Mounting FUSE Control File System...
[ 609.286385] systemd[1]: Mounting Kernel Configuration File System...
[ 609.287955] systemd[1]: First Boot Wizard was skipped because of an unmet condition check (ConditionFirstBoot=yes).
[ 609.292411] systemd[1]: Rebuild Hardware Database was skipped because of an unmet condition check (ConditionNeedsUpdate=/etc).
[ 609.296284] systemd[1]: Starting Load/Save Random Seed...
[ 609.302660] systemd[1]: Repartition Root Disk was skipped because no trigger condition checks were met.
[ 609.305612] systemd[1]: Starting Apply Kernel Variables...
[ 609.308060] systemd[1]: Create System Users was skipped because no trigger condition checks were met.
[ 609.311099] systemd[1]: Starting Create Static Device Nodes in /dev...
[ 609.316509] systemd[1]: Starting Setup Virtual Console...
[ 609.351398] systemd[1]: Finished Coldplug All udev Devices.
[ 609.352435] systemd[1]: Mounted FUSE Control File System.
[ 609.353334] systemd[1]: Mounted Kernel Configuration File System.
[ 609.391920] systemd[1]: Finished Load/Save Random Seed.
[ 609.412045] systemd[1]: Finished Apply Kernel Variables.
[ 609.452235] systemd[1]: Finished Setup Virtual Console.
[ 609.454308] systemd[1]: First Boot Complete was skipped because of an unmet condition check (ConditionFirstBoot=yes).
[ 609.541939] systemd[1]: Finished Create Static Device Nodes in /dev.
[ 609.543000] systemd[1]: Reached target Preparation for Local File Systems.
[ 609.568877] systemd[1]: Mounting Temporary /etc/pacman.d/gnupg directory...
[ 609.572222] systemd[1]: Virtual Machine and Container Storage (Compatibility) was skipped because of an unmet condition check (ConditionPathExists=/var/lib/machines.raw).
[ 609.572316] systemd[1]: Entropy Daemon based on the HAVEGE algorithm was skipped because of an unmet condition check (ConditionKernelVersion=<5.6).
[ 609.577747] systemd[1]: Starting Journal Service...
[ 609.583088] systemd[1]: Starting Rule-based Manager for Device Events and Files...
[ 609.589533] systemd[1]: Mounted Temporary /etc/pacman.d/gnupg directory.
[ 609.592419] systemd[1]: Reached target Local File Systems.
[ 609.595079] systemd[1]: Rebuild Dynamic Linker Cache was skipped because no trigger condition checks were met.
[ 609.597980] systemd[1]: Starting Tell Plymouth To Write Out Runtime Data...
[ 609.605852] systemd[1]: Set Up Additional Binary Formats was skipped because no trigger condition checks were met.
[ 609.605995] systemd[1]: Store a System Token in an EFI Variable was skipped because of an unmet condition check (ConditionPathExists=/sys/firmware/efi/efivars/LoaderFeatures-4a67b082-0a4c-41cf-b6c7-440b29bb8c4f).
[ 609.606107] systemd[1]: Commit a transient machine-id on disk was skipped because of an unmet condition check (ConditionPathIsMountPoint=/etc/machine-id).
[ 609.651344] systemd[1]: Finished Tell Plymouth To Write Out Runtime Data.
[ 609.652006] audit: type=1130 audit(1684312263.526:2): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=plymouth-read-write comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 609.676015] systemd[1]: Started Rule-based Manager for Device Events and Files.
[ 609.676686] audit: type=1130 audit(1684312263.549:3): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-udevd comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 609.676738] systemd[1]: Started Journal Service.
[ 609.677624] audit: type=1130 audit(1684312263.549:4): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-journald comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 609.730289] r8169 0000:02:00.0 enp2s0: renamed from eth0
[ 609.746219] systemd-journald[387]: Received client request to flush runtime journal.
[ 609.773969] mousedev: PS/2 mouse device common for all mice
[ 609.785732] audit: type=1130 audit(1684312263.659:5): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-journal-flush comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 609.785738] audit: type=1130 audit(1684312263.659:6): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=plymouth-start comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 609.912163] input: PC Speaker as /devices/platform/pcspkr/input/input16
[ 609.935080] audit: type=1130 audit(1684312263.809:7): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-backlight@backlight:intel_backlight comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 609.954773] intel-lpss 0000:00:15.0: enabling device (0000 -> 0002)
[ 609.955858] idma64 idma64.0: Found Intel integrated DMA 64-bit
[ 609.958717] mei_me 0000:00:16.0: enabling device (0000 -> 0002)
[ 609.965863] mc: Linux media interface: v0.10
[ 609.974033] input: Ideapad extra buttons as /devices/pci0000:00/0000:00:1f.0/PNP0C09:00/VPC2004:00/input/input17
[ 609.974132] ideapad_acpi VPC2004:00: Keyboard backlight control not available
[ 609.974327] i801_smbus 0000:00:1f.4: SPD Write Disable is set
[ 609.974374] i801_smbus 0000:00:1f.4: SMBus using PCI interrupt
[ 609.974425] pci 0000:00:1f.1: [8086:9d20] type 00 class 0x058000
[ 609.974483] pci 0000:00:1f.1: reg 0x10: [mem 0xfd000000-0xfdffffff 64bit]
[ 609.986511] i2c i2c-12: 2/2 memory slots populated (from DMI)
[ 609.991189] elan_i2c i2c-ELAN0611:00: supply vcc not found, using dummy regulator
[ 610.025548] Bluetooth: Core ver 2.22
[ 610.025565] NET: Registered PF_BLUETOOTH protocol family
[ 610.025567] Bluetooth: HCI device and connection manager initialized
[ 610.025570] Bluetooth: HCI socket layer initialized
[ 610.025572] Bluetooth: L2CAP socket layer initialized
[ 610.025574] Bluetooth: SCO socket layer initialized
[ 610.025711] ideapad_acpi VPC2004:00: DYTC interface is not available
[ 610.027043] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 610.027317] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 610.052113] audit: type=1130 audit(1684312263.926:8): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-tmpfiles-setup comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 610.058121] audit: type=1127 audit(1684312263.933:9): pid=473 uid=0 auid=4294967295 ses=4294967295 msg=' comm="systemd-update-utmp" exe="/usr/lib/systemd/systemd-update-utmp" hostname=? addr=? terminal=? res=success'
[ 610.078784] audit: type=1130 audit(1684312263.953:10): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-update-utmp comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 610.083987] audit: type=1130 audit(1684312263.956:11): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=cronie comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 610.107571] elan_i2c i2c-ELAN0611:00: Elan Touchpad: Module ID: 0x005b, Firmware: 0x0001, Sample: 0x0002, IAP: 0x0000
[ 610.107708] input: Elan Touchpad as /devices/pci0000:00/0000:00:15.0/i2c_designware.0/i2c-11/i2c-ELAN0611:00/input/input18
[ 610.140559] videodev: Linux video capture interface: v2.00
[ 610.160993] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_component_ops [i915])
[ 610.183170] RAPL PMU: API unit is 2^-32 Joules, 5 fixed counters, 655360 ms ovfl timer
[ 610.183175] RAPL PMU: hw unit of domain pp0-core 2^-14 Joules
[ 610.183177] RAPL PMU: hw unit of domain package 2^-14 Joules
[ 610.183179] RAPL PMU: hw unit of domain dram 2^-14 Joules
[ 610.183180] RAPL PMU: hw unit of domain pp1-gpu 2^-14 Joules
[ 610.183182] RAPL PMU: hw unit of domain psys 2^-14 Joules
[ 610.184181] iTCO_vendor_support: vendor-support=0
[ 610.216390] usbcore: registered new interface driver btusb
[ 610.229650] Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00000302.bin
[ 610.229654] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8, firmware rome 0x302 build 0x111
[ 610.251381] iTCO_wdt iTCO_wdt: Found a Intel PCH TCO device (Version=4, TCOBASE=0x0400)
[ 610.252237] iTCO_wdt iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 610.284813] usb 1-8: Found UVC 1.00 device EasyCamera (0bda:58ea)
[ 610.302921] input: EasyCamera: EasyCamera as /devices/pci0000:00/0000:00:14.0/usb1/1-8/1-8:1.0/input/input19
[ 610.303074] usbcore: registered new interface driver uvcvideo
[ 610.308534] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
[ 610.358184] ath10k_pci 0000:03:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 610.398569] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC236: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[ 610.398574] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 610.398576] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
[ 610.398578] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0
[ 610.398579] snd_hda_codec_realtek hdaudioC0D0: inputs:
[ 610.398580] snd_hda_codec_realtek hdaudioC0D0: Mic=0x19
[ 610.398582] snd_hda_codec_realtek hdaudioC0D0: Internal Mic=0x12
[ 610.411536] nouveau 0000:01:00.0: Enabling HDA controller
[ 610.513935] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input20
[ 610.513997] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1f.3/sound/card0/input21
[ 610.514042] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input22
[ 610.514084] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input23
[ 610.514130] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input24
[ 610.522341] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 610.522346] Bluetooth: BNEP filters: protocol multicast
[ 610.522350] Bluetooth: BNEP socket layer initialized
[ 610.609792] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[ 610.636204] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[ 610.658996] ath10k_pci 0000:03:00.0: qca9377 hw1.1 target 0x05020001 chip_id 0x003821ff sub 17aa:0901
[ 610.659002] ath10k_pci 0000:03:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 0 testmode 0
[ 610.659428] ath10k_pci 0000:03:00.0: firmware ver WLAN.TF.2.1-00021-QCARMSWP-1 api 6 features wowlan,ignore-otp crc32 42e41877
[ 610.669356] NET: Registered PF_QIPCRTR protocol family
[ 610.680853] intel_tcc_cooling: Programmable TCC Offset detected
[ 610.735442] ath10k_pci 0000:03:00.0: board_file api 2 bmi_id N/A crc32 8aedfa4a
[ 610.749255] intel_rapl_common: Found RAPL domain package
[ 610.749259] intel_rapl_common: Found RAPL domain core
[ 610.749261] intel_rapl_common: Found RAPL domain uncore
[ 610.749262] intel_rapl_common: Found RAPL domain dram
[ 610.749264] intel_rapl_common: Found RAPL domain psys
[ 610.817852] Generic FE-GE Realtek PHY r8169-0-200:00: attached PHY driver (mii_bus:phy_addr=r8169-0-200:00, irq=MAC)
[ 610.831361] ath10k_pci 0000:03:00.0: htt-ver 3.56 wmi-op 4 htt-op 3 cal otp max-sta 32 raw 0 hwcrypto 1
[ 610.859629] Bluetooth: MGMT ver 1.22
[ 610.867601] NET: Registered PF_ALG protocol family
[ 610.922795] ath: EEPROM regdomain: 0x6c
[ 610.922799] ath: EEPROM indicates we should expect a direct regpair map
[ 610.922800] ath: Country alpha2 being used: 00
[ 610.922801] ath: Regpair used: 0x6c
[ 610.997948] r8169 0000:02:00.0 enp2s0: Link is Down
[ 611.002104] ath10k_pci 0000:03:00.0 wlp3s0: renamed from wlan0
[ 611.081295] st: Version 20160209, fixed bufsize 32768, s/g segs 256
[ 611.102439] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 611.102468] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 616.028076] kauditd_printk_skb: 40 callbacks suppressed
[ 616.028078] audit: type=1131 audit(1684312269.903:52): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-rfkill comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 618.204623] nouveau 0000:01:00.0: Enabling HDA controller
[ 618.508208] audit: type=1130 audit(1684312272.383:53): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=plymouth-quit-wait comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 618.545279] audit: type=1130 audit(1684312272.419:54): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=plymouth-quit comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 618.568433] audit: type=1130 audit(1684312272.443:55): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=sddm comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 620.418644] audit: type=1100 audit(1684312274.293:56): pid=1097 uid=0 auid=4294967295 ses=4294967295 msg='op=PAM:authentication grantors=pam_faillock,pam_shells,pam_permit acct="manjaro" exe="/usr/lib/sddm/sddm-helper" hostname=? addr=? terminal=? res=success'
[ 620.419945] audit: type=1101 audit(1684312274.293:57): pid=1097 uid=0 auid=4294967295 ses=4294967295 msg='op=PAM:accounting grantors=pam_access,pam_unix,pam_permit,pam_time acct="manjaro" exe="/usr/lib/sddm/sddm-helper" hostname=? addr=? terminal=? res=success'
[ 620.420435] audit: type=1103 audit(1684312274.293:58): pid=1097 uid=0 auid=4294967295 ses=4294967295 msg='op=PAM:setcred grantors=pam_faillock,pam_shells,pam_permit acct="manjaro" exe="/usr/lib/sddm/sddm-helper" hostname=? addr=? terminal=? res=success'
[ 620.420506] audit: type=1006 audit(1684312274.293:59): pid=1097 uid=0 old-auid=4294967295 auid=1000 tty=(none) old-ses=4294967295 ses=1 res=1
[ 620.420510] audit: type=1300 audit(1684312274.293:59): arch=c000003e syscall=1 success=yes exit=4 a0=8 a1=7ffe9d168d90 a2=4 a3=0 items=0 ppid=1064 pid=1097 auid=1000 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=1 comm="sddm-helper" exe="/usr/lib/sddm/sddm-helper" key=(null)
[ 620.420513] audit: type=1327 audit(1684312274.293:59): proctitle=2F7573722F6C69622F7364646D2F7364646D2D68656C706572002D2D736F636B6574002F746D702F7364646D2D6175746839643830653964662D643238642D343235352D396338632D383366353839336166333765002D2D69640031002D2D7374617274002F7573722F62696E2F7374617274706C61736D612D783131002D2D
[ 621.788155] kauditd_printk_skb: 10 callbacks suppressed
[ 621.788158] audit: type=1130 audit(1684312275.663:68): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=NetworkManager-wait-online comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 621.969224] audit: type=1130 audit(1684312275.843:69): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=udisks2 comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 621.971951] audit: type=1334 audit(1684312275.846:70): prog-id=35 op=LOAD
[ 621.971983] audit: type=1334 audit(1684312275.846:71): prog-id=36 op=LOAD
[ 621.974158] audit: type=1130 audit(1684312275.846:72): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=rtkit-daemon comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 622.146853] audit: type=1130 audit(1684312276.019:73): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=upower comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 622.259107] audit: type=1130 audit(1684312276.133:74): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-rfkill comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 623.360448] audit: type=1130 audit(1684312277.233:75): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=power-profiles-daemon comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 623.607742] audit: type=1101 audit(1684312277.479:76): pid=1512 uid=1000 auid=1000 ses=2 msg='op=PAM:accounting grantors=pam_unix,pam_permit,pam_time acct="manjaro" exe="/usr/bin/sudo" hostname=? addr=? terminal=? res=success'
[ 623.609093] audit: type=1110 audit(1684312277.483:77): pid=1512 uid=1000 auid=1000 ses=2 msg='op=PAM:setcred grantors=pam_faillock,pam_permit,pam_env,pam_faillock acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=? res=success'
[ 626.003953] Bluetooth: RFCOMM TTY layer initialized
[ 626.003962] Bluetooth: RFCOMM socket layer initialized
[ 626.003968] Bluetooth: RFCOMM ver 1.11
[ 627.291418] kauditd_printk_skb: 8 callbacks suppressed
[ 627.291420] audit: type=1131 audit(1684312281.166:86): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-rfkill comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 640.754802] audit: type=1131 audit(1684312294.629:87): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-hostnamed comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 640.824603] audit: type=1334 audit(1684312294.699:88): prog-id=34 op=UNLOAD
[ 640.824611] audit: type=1334 audit(1684312294.699:89): prog-id=33 op=UNLOAD
[ 640.824615] audit: type=1334 audit(1684312294.699:90): prog-id=32 op=UNLOAD
[ 668.448846] audit: type=1130 audit(1684312322.323:91): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=pacman-init comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 923.615505] audit: type=1130 audit(1684312577.489:92): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-tmpfiles-clean comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 923.615540] audit: type=1131 audit(1684312577.489:93): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-tmpfiles-clean comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 1057.177439] logitech-hidpp-device 0003:046D:4074.0004: HID++ 4.2 device connected.
[ 1073.490963] audit: type=1111 audit(1684312727.363:94): pid=554 uid=0 auid=4294967295 ses=4294967295 msg='op=connection-add-activate uuid=8f984fc8-e994-410f-875b-8ba00c326068 name=505249594F204241534E4554574F524B pid=1273 uid=1000 result=success exe="/usr/bin/NetworkManager" hostname=? addr=? terminal=? res=success'
[ 1078.427422] wlp3s0: authenticate with e8:65:d4:c5:ad:20
[ 1078.427468] wlp3s0: 80 MHz not supported, disabling VHT
[ 1078.459762] wlp3s0: send auth to e8:65:d4:c5:ad:20 (try 1/3)
[ 1078.461828] wlp3s0: authenticated
[ 1078.464502] wlp3s0: associate with e8:65:d4:c5:ad:20 (try 1/3)
[ 1078.483455] wlp3s0: RX AssocResp from e8:65:d4:c5:ad:20 (capab=0x411 status=0 aid=8)
[ 1078.486869] wlp3s0: associated
[ 1078.591779] IPv6: ADDRCONF(NETDEV_CHANGE): wlp3s0: link becomes ready
[ 1079.537028] audit: type=1130 audit(1684312733.409:95): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=NetworkManager-dispatcher comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 1089.592248] audit: type=1131 audit(1684312743.466:96): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=NetworkManager-dispatcher comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 1189.578578] audit: type=1101 audit(1684312843.453:97): pid=3130 uid=1000 auid=1000 ses=2 msg='op=PAM:accounting grantors=pam_unix,pam_permit,pam_time acct="manjaro" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/2 res=success'
[ 1189.579742] audit: type=1110 audit(1684312843.453:98): pid=3130 uid=1000 auid=1000 ses=2 msg='op=PAM:setcred grantors=pam_faillock,pam_permit,pam_env,pam_faillock acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/2 res=success'
[ 1189.579955] audit: type=1105 audit(1684312843.453:99): pid=3130 uid=1000 auid=1000 ses=2 msg='op=PAM:session_open grantors=pam_systemd_home,pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/2 res=success'
[ 1189.608873] audit: type=1106 audit(1684312843.483:100): pid=3130 uid=1000 auid=1000 ses=2 msg='op=PAM:session_close grantors=pam_systemd_home,pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/2 res=success'
[ 1189.608940] audit: type=1104 audit(1684312843.483:101): pid=3130 uid=1000 auid=1000 ses=2 msg='op=PAM:setcred grantors=pam_faillock,pam_permit,pam_env,pam_faillock acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/2 res=success'
[ 1336.570345] audit: type=1101 audit(1684312990.443:102): pid=3160 uid=1000 auid=1000 ses=2 msg='op=PAM:accounting grantors=pam_unix,pam_permit,pam_time acct="manjaro" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/2 res=success'
[ 1336.571378] audit: type=1110 audit(1684312990.446:103): pid=3160 uid=1000 auid=1000 ses=2 msg='op=PAM:setcred grantors=pam_faillock,pam_permit,pam_env,pam_faillock acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/2 res=success'
[ 1336.571558] audit: type=1105 audit(1684312990.446:104): pid=3160 uid=1000 auid=1000 ses=2 msg='op=PAM:session_open grantors=pam_systemd_home,pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/2 res=success'can anyone help me figure out what these output means?
Last edited by priyoislam (2023-05-17 12:13:17)
Offline
#4 2023-05-17 12:15:13
- seth
- Member
- Registered: 2012-09-03
- Posts: 51,213
Re: Input/output error while recovering journal of /dev/sda2
[ 604.026246] ahci 0000:00:17.0: port does not support device sleep
[ 604.026445] ata1: EH complete
[ 604.058348] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x40000 action 0x0
[ 604.058364] ata1.00: irq_stat 0x40000001
[ 604.058369] ata1: SError: { CommWake }
[ 604.058380] ata1.00: failed command: WRITE DMA EXT
[ 604.058385] ata1.00: cmd 35/00:08:78:70:ef/00:00:5c:00:00/e0 tag 15 dma 4096 out
res 51/04:08:78:70:ef/00:00:5c:00:00/e0 Emask 0x1 (device error)
[ 604.058407] ata1.00: status: { DRDY ERR }
[ 604.058412] ata1.00: error: { ABRT }
[ 604.069101] ahci 0000:00:17.0: port does not support device sleep
[ 604.075438] ata1.00: configured for UDMA/100Cable, power cable, overly aggressive powersaving or the drive is dying.
Wrt
live env with a usb . same problem occurred
the underpowering is in the BIOS or not the cause.
Check the cables and/or ideally the drive in a different system.
Offline