You are not logged in.

#1 2024-03-29 23:56:05

canegiallo
Member
Registered: 2016-11-18
Posts: 14

Set uncommon screen resolution with an Arc 380

I have a monitor with an uncommon resolution (1920x860). When I connect it to the iGPU (Intel Iris Pro II) its native resolution is detected egregiously; however, if I connect it to the GPU (Intel Arc 380) the only resolution provided is 1280x720. I can only connect it via HDMI.

On Wayland the resolution of this trouble is quite impossible at the moment: the edid file of said monitor is wrong (I have neither the skills nor the ability to write about it and I cannot risk damaging the hardware learning or experimenting).

On X11 something is doable thanks to xrandr, but always limited. I can indeed enable 1920x1080, which comes a little close to the native resolution of my screen, but the form factor is wrong (and the screen looks smeared/stretched).

To come to this conclusion I had to make many attempts, but unfortunately after a month I am still with a GPU that cannot set the resolution of my monitor correctly.

I am on Artix Linux Kernel 6.8.2-artix1-1, plasmashell 6.0.2, X11. I am using the i915 driver, properly loaded. Here are some other infos, hope someone could be of some help.

$ lspci | grep VGA
03:00.0 VGA compatible controller: Intel Corporation DG2 [Arc A380] (rev 05)
$ glxinfo | grep "OpenGL version"
OpenGL version string: 4.6 (Compatibility Profile) Mesa 24.0.3-arch1.2
$ xrandr
Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 16384 x 16384
HDMI-3 connected primary 1920x1080+0+0 (normal left inverted right x axis y axis) 278mm x 124mm
   1280x720      60.00    59.94  
   1920x1080R    59.93* <-- note: manually added (working)
   1920x860R     59.89  <-- note: manually added (not working)
DP-3 disconnected (normal left inverted right x axis y axis)
HDMI-4 disconnected (normal left inverted right x axis y axis)
VGA-1-1 disconnected (normal left inverted right x axis y axis)
DP-1-1 disconnected (normal left inverted right x axis y axis)
HDMI-1-1 disconnected (normal left inverted right x axis y axis)
DP-1-2 disconnected (normal left inverted right x axis y axis)
HDMI-1-2 disconnected (normal left inverted right x axis y axis)

the wrong edid via $ get-edid | parse-edid:

Section "Monitor"
        Identifier "L1"
        ModelName "L1"
        VendorName "MSR"
        # Monitor Manufactured week 23 of 2021
        # EDID version 1.3
        # Digital Display
        DisplaySize 270 120
        Gamma 2.20
        Option "DPMS" "true"
        Horizsync 30-81
        VertRefresh 56-76
        # Maximum pixel clock is 170MHz
        #Not giving standard mode: 1280x720, 60Hz

        #Extension block found. Parsing...
        Modeline        "Mode 2" +hsync +vsync interlace
        Modeline        "Mode 0" +hsync +vsync 
        Modeline        "Mode 1" 74.250 1280 1390 1420 1650 720 725 730 750 +hsync +vsync
        Option "PreferredMode" "Mode 2"
EndSection
$ grep EE /var/log/Xorg.0.log
[     4.530] Current Operating System: Linux red 6.8.2-artix1-1 #1 SMP PREEMPT_DYNAMIC Wed, 27 Mar 2024 20:16:29 +0000 x86_64
        (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[     4.554] (EE) Failed to load module "intel" (module does not exist, 0)
[     4.558] (EE) Failed to load /usr/lib/xorg/modules/drivers/fbdev_drv.so: /usr/lib/xorg/modules/drivers/fbdev_drv.so: undefined symbol: fbdevHWSave
[     4.558] (EE) Failed to load module "fbdev" (loader failed, 0)
[     5.165] (II) Initializing extension MIT-SCREEN-SAVER
[    14.433] (II) XINPUT: Adding extended input device "BJYP-L1 Device BJYP-L1-V1.09" (type: TOUCHSCREEN, id 16)
[    50.663] (II) XINPUT: Adding extended input device "BJYP-L1 Device BJYP-L1-V1.09" (type: TOUCHSCREEN, id 16)
[   480.527] (EE) modeset(0): failed to set mode: No such file or directory
[   492.496] (II) XINPUT: Adding extended input device "BJYP-L1 Device BJYP-L1-V1.09" (type: TOUCHSCREEN, id 16)
$ grep WW /var/log/Xorg.0.log
        (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[     4.535] (WW) The directory "/usr/share/fonts/misc" does not exist.
[     4.537] (WW) The directory "/usr/share/fonts/Type1" does not exist.
[     4.537] (WW) The directory "/usr/share/fonts/100dpi" does not exist.
[     4.537] (WW) The directory "/usr/share/fonts/75dpi" does not exist.
[     4.554] (WW) Warning, couldn't open module intel

and dmesg | grep i915:

    2.324978] i915 0000:00:02.0: [drm] Found 128MB of eDRAM
[    2.325745] i915 0000:00:02.0: ROM [??? 0x00000000 flags 0x20000000]: can't assign; bogus alignment
[    2.325749] i915 0000:00:02.0: [drm] Failed to find VBIOS tables (VBT)
[    2.326197] WARNING: CPU: 1 PID: 451 at drivers/gpu/drm/i915/display/intel_ddi.c:4793 intel_ddi_init+0x1b5/0x1050 [i915]
[    2.326396] Modules linked in: usbhid(+) crct10dif_pclmul apple_mfi_fastcharge crc32_pclmul polyval_clmulni polyval_generic i915(+) gf128mul ghash_clmulni_intel snd_hda_codec_realtek snd_hda_codec_generic sha512_ssse3 sha256_ssse3 eeepc_wmi sha1_ssse3 aesni_intel asus_wmi snd_hda_intel snd_intel_dspcfg ledtrig_audio platform_profile snd_intel_sdw_acpi i8042 crypto_simd snd_hda_codec sparse_keymap cryptd drm_buddy i2c_algo_bit serio iTCO_wdt rapl ppdev at24 snd_hda_core rfkill intel_pmc_bxt ttm intel_cstate mei_hdcp mxm_wmi iTCO_vendor_support mei_pxp wmi_bmof intel_uncore snd_hwdep drm_display_helper snd_pcm i2c_i801 i2c_dev cec snd_timer crypto_user intel_gtt lpc_ich i2c_smbus pcspkr e1000e snd mei_me ptp soundcore parport_pc video mei pps_core parport mac_hid wmi acpi_pad ext4 crc32c_generic crc16 mbcache jbd2 crc32c_intel xhci_pci xhci_pci_renesas
[    2.326449] RIP: 0010:intel_ddi_init+0x1b5/0x1050 [i915]
[    2.326625]  ? intel_ddi_init+0x1b5/0x1050 [i915 ba15940b0812ba6411d4d08f04798e49b3370e47]
[    2.326784]  ? intel_ddi_init+0x1b5/0x1050 [i915 ba15940b0812ba6411d4d08f04798e49b3370e47]
[    2.326956]  ? __pfx_intel_ddi_init+0x10/0x10 [i915 ba15940b0812ba6411d4d08f04798e49b3370e47]
[    2.327110]  ? intel_ddi_init+0x1b5/0x1050 [i915 ba15940b0812ba6411d4d08f04798e49b3370e47]
[    2.327267]  ? intel_ddi_init+0x1b5/0x1050 [i915 ba15940b0812ba6411d4d08f04798e49b3370e47]
[    2.327433]  ? __pfx_intel_ddi_init+0x10/0x10 [i915 ba15940b0812ba6411d4d08f04798e49b3370e47]
[    2.327588]  intel_bios_for_each_encoder+0x38/0x50 [i915 ba15940b0812ba6411d4d08f04798e49b3370e47]
[    2.327753]  intel_setup_outputs+0x386/0x8b0 [i915 ba15940b0812ba6411d4d08f04798e49b3370e47]
[    2.327933]  intel_display_driver_probe_nogem+0x14c/0x210 [i915 ba15940b0812ba6411d4d08f04798e49b3370e47]
[    2.328096]  i915_driver_probe+0x656/0xba0 [i915 ba15940b0812ba6411d4d08f04798e49b3370e47]
[    2.328263]  i915_init+0x25/0xc0 [i915 ba15940b0812ba6411d4d08f04798e49b3370e47]
[    2.328391]  ? __pfx_i915_init+0x10/0x10 [i915 ba15940b0812ba6411d4d08f04798e49b3370e47]
[    2.330341] [drm] Initialized i915 1.6.0 20230929 for 0000:00:02.0 on minor 1
[    2.330639] i915 display info: display version: 8
[    2.330641] i915 display info: cursor_needs_physical: no
[    2.330642] i915 display info: has_cdclk_crawl: no
[    2.330643] i915 display info: has_cdclk_squash: no
[    2.330644] i915 display info: has_ddi: yes
[    2.330644] i915 display info: has_dp_mst: yes
[    2.330645] i915 display info: has_dsb: no
[    2.330646] i915 display info: has_fpga_dbg: yes
[    2.330646] i915 display info: has_gmch: no
[    2.330647] i915 display info: has_hotplug: yes
[    2.330648] i915 display info: has_hti: no
[    2.330648] i915 display info: has_ipc: no
[    2.330649] i915 display info: has_overlay: no
[    2.330650] i915 display info: has_psr: yes
[    2.330650] i915 display info: has_psr_hw_tracking: yes
[    2.330651] i915 display info: overlay_needs_physical: no
[    2.330652] i915 display info: supports_tv: no
[    2.330652] i915 display info: has_hdcp: no
[    2.330653] i915 display info: has_dmc: no
[    2.330653] i915 display info: has_dsc: no
[    2.343211] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
[    2.343264] snd_hda_intel 0000:00:03.0: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
[    2.346501] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
[    2.350364] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
[    2.370415] i915 0000:03:00.0: vgaarb: deactivate vga console
[    2.370753] i915 0000:03:00.0: [drm] Can't resize LMEM BAR - platform support is missing
[    2.370766] i915 0000:03:00.0: [drm] Local memory IO size: 0x0000000010000000
[    2.370768] i915 0000:03:00.0: [drm] Local memory available: 0x000000017c800000
[    2.370769] i915 0000:03:00.0: [drm] Using a reduced BAR size of 256MiB. Consider enabling 'Resizable BAR' or similar, if available in the BIOS.
[    2.392428] i915 0000:03:00.0: [drm] Finished loading DMC firmware i915/dg2_dmc_ver2_08.bin (v2.8)
[    2.402470] i915 0000:03:00.0: [drm] GT0: GuC firmware i915/dg2_guc_70.bin version 70.20.0
[    2.402474] i915 0000:03:00.0: [drm] GT0: HuC firmware i915/dg2_huc_gsc.bin version 7.10.3
[    2.413667] i915 0000:03:00.0: [drm] GT0: GUC: submission enabled
[    2.413670] i915 0000:03:00.0: [drm] GT0: GUC: SLPC enabled
[    2.413910] i915 0000:03:00.0: [drm] GT0: GUC: RC enabled
[    2.473066] [drm] Initialized i915 1.6.0 20230929 for 0000:03:00.0 on minor 2
[    2.474053] i915 display info: display version: 13
[    2.474055] i915 display info: cursor_needs_physical: no
[    2.474056] i915 display info: has_cdclk_crawl: no
[    2.474057] i915 display info: has_cdclk_squash: yes
[    2.474058] i915 display info: has_ddi: yes
[    2.474059] i915 display info: has_dp_mst: yes
[    2.474059] i915 display info: has_dsb: yes
[    2.474060] i915 display info: has_fpga_dbg: yes
[    2.474061] i915 display info: has_gmch: no
[    2.474061] i915 display info: has_hotplug: yes
[    2.474062] i915 display info: has_hti: no
[    2.474063] i915 display info: has_ipc: yes
[    2.474063] i915 display info: has_overlay: no
[    2.474064] i915 display info: has_psr: yes
[    2.474064] i915 display info: has_psr_hw_tracking: no
[    2.474065] i915 display info: overlay_needs_physical: no
[    2.474066] i915 display info: supports_tv: no
[    2.474066] i915 display info: has_hdcp: yes
[    2.474067] i915 display info: has_dmc: yes
[    2.474068] i915 display info: has_dsc: yes
[    2.499911] snd_hda_intel 0000:04:00.0: bound 0000:03:00.0 (ops i915_audio_component_bind_ops [i915])
[    2.501894] fbcon: i915drmfb (fb0) is primary device
[    2.575285] i915 0000:03:00.0: [drm] fb0: i915drmfb frame buffer device
[    3.135620] mei i915.mei-gscfi.768-46e0c1fb-a546-414f-9170-b7f46d57b4ad: Could not read FW version ret = -19
[    3.135623] mei i915.mei-gscfi.768-46e0c1fb-a546-414f-9170-b7f46d57b4ad: FW version command failed -5
[    3.541576] i915 0000:03:00.0: [drm] GT0: HuC: authenticated for all workloads
[    3.541583] mei_pxp i915.mei-gsc.768-fbf6fcf1-96cf-4e2e-a6a6-1bab8cbe36b1: bound 0000:03:00.0 (ops i915_pxp_tee_component_ops [i915])

Thank you for your time and patience.

Offline

#2 2024-03-31 07:57:24

canegiallo
Member
Registered: 2016-11-18
Posts: 14

Re: Set uncommon screen resolution with an Arc 380

Interesting Updates:

I tested my monitor with Windows 10 to see if I could get more interesting information, and indeed there were some advances:

Using EnTech Monitor Asset Manager, I got a complete readout of the edid file, and this is where the interesting news popped up: the edid.bin file of my monitor reads:

Native/preferred timing... 1920x860p at 60Hz 
    Modeline............... "1920x860" 110,680 1920 1968 2000 2106 860 863 868 876 +hsync +vsync

Standard timings supported
    1280 x 720p at 60Hz - VESA STD

.

So I tried again using the edid.bin file and:

- I put the edid file in /usr/lib/firmware/edid/.
- I set

MODULES=(i915)

and

FILES="/usr/lib/firmware/edid/edid.bin"

in /etc/mkinitcpio.conf. Then ran

mkinitcpio -P

- I put the KMS

drm.edid_firmware=HDMI-1:edid/edid.bin drm.edid_firmware=HDMI-A-1:edid/edid.bin

in the GRUB_CMDLINE_LINUX_DEFAULT of /etc/default/grub. Then clearly run

grub-mkconfig -o /boot/grub/grub.cfg

(I set the custom edid two times since HDMI-1 is the way X11 identifies my monitor and HDMI-A-1 since it is the way Wayland identifies it).

Now if I check with dmesg there is no error and the edid file is loaded correctly without any problems, as is the i915 module.
The Xorg log is also completely clean and there are no problems. The i915 driver is loaded correctly and the only missing feature (due to my motherboard) is the resizeable BAR, which is not important to solve this problem.

Despite this, on both Wayland and X11 the only resolution that can be set is 1280x720 (always stretched). Using X11 and xrandr I can add the modeline 1920x1080 and use it (maybe because it is Standard) but still everything is stretched since it doesn't respect the screen ratio.

So I tried configuring inside /etc/X11/xorg.conf.d/20-intel.conf file:

Section "Device"
    Identifier "IntelGraphics"
    Driver "modesetting"
#    Driver "intel"
    Option "AccelMethod" "sna"
    Option "DRI" "iris"
#	Option "DRI" "2"
    Option "CustomEDID" "HDMI-1:/usr/lib/firmware/edid/edid.bin"
    Option "CustomEDID" "HDMI-A-1:/usr/lib/firmware/edid/edid.bin"
    Option "IgnoreEDID" "false"
    Option "UseEDID" "true"
EndSection

.

But despite all this, on both X11 and Wayland the only resolution that can be set is 1280x720.

I tried to user xrandr on X11 to therefore add by hand the modeline specified in the edid file ("1920x860" 110,680 1920 1968 2000 2106 860 863 868 876 +hsync +vsync). Doesn't work.

If I use the Arc 830 it seems that I can only set the Vesa Standard resolution (1280x720) and not the preferred one indicated in the edid file (1920x860). This is so annoying.

I hope someone can help me or can give me further guidance and that this information can be a guide for those in the same situation as me. I would like to do a bug report in regard to this issue, but doesn't know where/who.

ps: if some info or reports are needed please let me know.

Offline

#3 2024-03-31 09:08:07

seth
Member
Registered: 2012-09-03
Posts: 52,199

Re: Set uncommon screen resolution with an Arc 380

Please post your Xorg log, https://wiki.archlinux.org/title/Xorg#General and the output of

for OUT in /sys/class/drm/card*; do echo $OUT; edid-decode $OUT/edid; echo "================="; done

You'll need https://aur.archlinux.org/packages/edid-decode-git
when the output is connected to the Arc 830

Your xorg config there is a wild mix ofthe modesetting driver with options that are only available/resonable w/ xf86-video-intel andthe nvidia driver…

Offline

#4 2024-03-31 09:51:18

canegiallo
Member
Registered: 2016-11-18
Posts: 14

Re: Set uncommon screen resolution with an Arc 380

First of all: thank you for your time and patience!

Here is the xorg log (I managed to get the lines since last boot):

[    20.308] (II) event1  - Power Button: device removed
[    20.320] (II) event0  - Power Button: device removed
[    20.336] (II) event16 - Kensington Expert Wireless TB Mouse: device removed
[    20.383] (II) event17 - Kensington Expert Wireless TB Consumer Control: device removed
[    20.403] (II) event18 - IQUNIX IQUNIX OG80 Mechanical Keyboard: device removed
[    20.420] (II) event3  - Eee PC WMI hotkeys: device removed
[    20.436] (II) event19 - IQUNIX IQUNIX OG80 Mechanical Keyboard: device removed
[    20.453] (II) event21 - BJYP-L1 Device BJYP-L1-V1.09: device removed
[    20.500] (II) event20 - BJYP-L1 Device BJYP-L1-V1.09: device removed
[    22.864] (II) config/udev: removing device BJYP-L1 Device BJYP-L1-V1.09
[    22.864] (II) UnloadModule: "libinput"
[    22.961] (II) config/udev: removing device BJYP-L1 Device BJYP-L1-V1.09
[    22.961] (II) UnloadModule: "libinput"
[    32.902] (II) config/udev: Adding input device BJYP-L1 Device BJYP-L1-V1.09 (/dev/input/mouse3)
[    32.902] (**) BJYP-L1 Device BJYP-L1-V1.09: Applying InputClass "system-mouse"
[    32.902] (II) No input driver specified, ignoring this device.
[    32.902] (II) This device may have been added with another device file.
[    32.904] (II) config/udev: Adding input device BJYP-L1 Device BJYP-L1-V1.09 (/dev/input/mouse2)
[    32.904] (II) No input driver specified, ignoring this device.
[    32.904] (II) This device may have been added with another device file.
[    32.997] (II) config/udev: Adding input device BJYP-L1 Device BJYP-L1-V1.09 (/dev/input/event21)
[    32.997] (**) BJYP-L1 Device BJYP-L1-V1.09: Applying InputClass "libinput pointer catchall"
[    32.997] (**) BJYP-L1 Device BJYP-L1-V1.09: Applying InputClass "system-mouse"
[    32.997] (II) Using input driver 'libinput' for 'BJYP-L1 Device BJYP-L1-V1.09'
[    32.997] (**) BJYP-L1 Device BJYP-L1-V1.09: always reports core events
[    32.997] (**) Option "Device" "/dev/input/event21"
[    33.055] (II) event21 - BJYP-L1 Device BJYP-L1-V1.09: is tagged by udev as: Mouse
[    33.055] (II) event21 - BJYP-L1 Device BJYP-L1-V1.09: device is a pointer
[    33.055] (II) event21 - BJYP-L1 Device BJYP-L1-V1.09: device removed
[    33.070] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-3/3-3.3/3-3.3:1.1/0003:28E9:028A.0009/input/input25/event21"
[    33.070] (II) XINPUT: Adding extended input device "BJYP-L1 Device BJYP-L1-V1.09" (type: MOUSE, id 14)
[    33.070] (**) Option "AccelerationScheme" "none"
[    33.070] (**) BJYP-L1 Device BJYP-L1-V1.09: (accel) selected scheme none/0
[    33.070] (**) BJYP-L1 Device BJYP-L1-V1.09: (accel) acceleration factor: 2.000
[    33.070] (**) BJYP-L1 Device BJYP-L1-V1.09: (accel) acceleration threshold: 4
[    33.070] (II) config/udev: Adding input device BJYP-L1 Device BJYP-L1-V1.09 (/dev/input/event22)
[    33.070] (II) No input driver specified, ignoring this device.
[    33.070] (II) This device may have been added with another device file.
[    33.071] (II) config/udev: Adding input device BJYP-L1 Device BJYP-L1-V1.09 (/dev/input/event20)
[    33.071] (**) BJYP-L1 Device BJYP-L1-V1.09: Applying InputClass "libinput touchscreen catchall"
[    33.071] (II) Using input driver 'libinput' for 'BJYP-L1 Device BJYP-L1-V1.09'
[    33.071] (**) BJYP-L1 Device BJYP-L1-V1.09: always reports core events
[    33.071] (**) Option "Device" "/dev/input/event20"
[    33.081] (II) event20 - BJYP-L1 Device BJYP-L1-V1.09: is tagged by udev as: Touchscreen
[    33.081] (II) event20 - BJYP-L1 Device BJYP-L1-V1.09: device is a touch device
[    33.081] (II) event20 - BJYP-L1 Device BJYP-L1-V1.09: device removed
[    33.116] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-3/3-3.3/3-3.3:1.0/0003:28E9:028A.0008/input/input24/event20"
[    33.116] (II) XINPUT: Adding extended input device "BJYP-L1 Device BJYP-L1-V1.09" (type: TOUCHSCREEN, id 15)
[    33.116] (**) Option "AccelerationScheme" "none"
[    33.116] (**) BJYP-L1 Device BJYP-L1-V1.09: (accel) selected scheme none/0
[    33.116] (**) BJYP-L1 Device BJYP-L1-V1.09: (accel) acceleration factor: 2.000
[    33.116] (**) BJYP-L1 Device BJYP-L1-V1.09: (accel) acceleration threshold: 4

Here is the edid one:

$ for OUT in /sys/class/drm/card*; do echo $OUT; edid-decode $OUT/edid; echo "================="; done
/sys/class/drm/card1
/sys/class/drm/card1/edid: No such file or directory
=================
/sys/class/drm/card1-DP-1
EDID of '/sys/class/drm/card1-DP-1/edid' was empty.
=================
/sys/class/drm/card1-HDMI-A-1
edid-decode (hex):

00 ff ff ff ff ff ff 00 36 72 18 04 18 04 23 20
17 1f 01 03 80 1b 0c 78 ea 1e c5 ae 4f 34 b1 26
0e 50 54 00 00 00 81 c0 01 01 01 01 01 01 01 01
01 01 01 01 01 01 3c 2b 80 ba 70 5c 10 30 30 20
35 00 16 7c 10 00 00 1e 00 00 00 ff 00 4c 31 2d
32 30 32 33 30 34 31 38 0a 20 00 00 00 fc 00 4c
31 0a 20 20 20 20 20 20 20 20 20 20 00 00 00 fd
00 38 4c 1e 51 11 00 0a 20 20 20 20 20 20 01 cc

00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

----------------

Block 0, Base EDID:
  EDID Structure Version & Revision: 1.3
  Vendor & Product Identification:
    Manufacturer: MSR
    Model: 1048
    Serial Number: 539165720 (0x20230418)
    Made in: week 23 of 2021
  Basic Display Parameters & Features:
    Digital display
    Maximum image size: 27 cm x 12 cm
    Gamma: 2.20
    DPMS levels: Standby Suspend Off
    RGB color display
    First detailed timing is the preferred timing
  Color Characteristics:
    Red  : 0.6796, 0.3095
    Green: 0.2060, 0.6933
    Blue : 0.1513, 0.0546
    White: 0.3134, 0.3291
  Established Timings I & II: none
  Standard Timings:
    DMT 0x55:  1280x720    60.000000 Hz  16:9     45.000 kHz     74.250000 MHz
  Detailed Timing Descriptors:
    DTD 1:  1920x860    59.993842 Hz  96:43    52.555 kHz    110.680000 MHz (278 mm x 124 mm)
                 Hfront   48 Hsync  32 Hback  106 Hpol P
                 Vfront    3 Vsync   5 Vback    8 Vpol P
    Display Product Serial Number: 'L1-20230418'
    Display Product Name: 'L1'
    Display Range Limits:
      Monitor ranges (GTF): 56-76 Hz V, 30-81 kHz H, max dotclock 170 MHz
  Extension blocks: 1
Checksum: 0xcc

----------------

Block 1, Unknown EDID Extension Block 0x00:
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 '................'
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 '................'
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 '................'
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 '................'
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 '................'
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 '................'
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 '................'
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 '................'
Checksum: 0x00
=================
/sys/class/drm/card1-HDMI-A-2
EDID of '/sys/class/drm/card1-HDMI-A-2/edid' was empty.
=================

About my messy xorg config: yes, I did so many tries that it is a bit messy now and should be cleaned/rewritten. sad
Hopefully those infos can help

Offline

#5 2024-03-31 09:55:03

seth
Member
Registered: 2012-09-03
Posts: 52,199

Re: Set uncommon screen resolution with an Arc 380

That's not your xorg log, it's a small and irrelevant fraction of it.

card1-HDMI-A-1 shows up w/ the desired mode in DTD1 which "First detailed timing is the preferred timing" is what you should™ be getting there.
There's also a bogus extension block, no idea whether that's gonna throw off X11 or wayland

Offline

#6 2024-03-31 09:58:01

canegiallo
Member
Registered: 2016-11-18
Posts: 14

Re: Set uncommon screen resolution with an Arc 380

I am sorry,
here is the complete Xorg.0.log https://pastebin.com/JWmP5imk

Offline

#7 2024-03-31 10:08:40

seth
Member
Registered: 2012-09-03
Posts: 52,199

Re: Set uncommon screen resolution with an Arc 380

[     4.921] Current Operating System: Linux red 6.8.2-artix1-1 #1 SMP PREEMPT_DYNAMIC Wed, 27 Mar 2024 20:16:29 +0000 x86_64

https://bbs.archlinux.org/misc.php?action=rules

It reads the correct edid, finds the 860p modeline but then goes on to

[     4.971] (II) modeset(0): Printing probed modes for output HDMI-1
[     4.971] (II) modeset(0): Modeline "1280x720"x60.0   74.25  1280 1390 1430 1650  720 725 730 750 +hsync +vsync (45.0 kHz e)
[     4.925] (**) |-->Screen "HDMI-1" (0)
[     4.925] (**) |   |-->Monitor "Monitor0"
[     4.925] (**) |   |-->Device "IntelGraphics"
…
[     4.969] (II) modeset(0): Output HDMI-1 using monitor section Monitor0

might be a problem here, and for some reason we arrive at

[     5.120] (II) AIGLX: Screen 0 is not DRI2 capable
[     5.264] (II) IGLX: Loaded and initialized swrast
[     5.264] (II) GLX: Initialized DRISWRAST GL provider for screen 0

The problem is likely the underlying kernel module.
Clean up your xorg config (remove everything you added there custom) and post your complete system journal for the boot:

sudo journalctl -b | curl -F 'file=@-' 0x0.st

Be prepared that a mod will close this thread anytime they see it.

Offline

#8 2024-03-31 10:26:28

canegiallo
Member
Registered: 2016-11-18
Posts: 14

Re: Set uncommon screen resolution with an Arc 380

I didn't mean to be negligent, I hope the fact that this problem is there has nothing to do with the fact that I have runit and an artix kernel.

So I cannot journalctl, but I can:

# dmesg | curl -F 'file=@-' 0x0.st
http://0x0.st/XzBB.txt

Which contains: https://pastebin.com/2abnHkSq

I thank you deeply for your assistance up to this point.

Offline

#9 2024-03-31 13:30:49

seth
Member
Registered: 2012-09-03
Posts: 52,199

Re: Set uncommon screen resolution with an Arc 380

Sorry I forgot why Artix exists - plus I'm habitually posting textblocks for this wink

There isn't anything suspicious in the dmesg, maybe add "initcall_blacklist=simpledrm_platform_driver_init" to the https://wiki.archlinux.org/title/Kernel_parameters to get that out of the equation.
Did you meanwhile remove your xorg confliglets? What's the impact on the xorg log and situation?

Somewhere in the back of my head there was an over-aggressive modeline filter, but iirc that only applied to the amdgpu driver and has been quite a while
You could still try your luck w/ intel but need to explicitly select the iris DRI.
Do you btw. try to use mesa-amber? Don't.

You could try to set a mode for KMS and maybe get it down to wayland this way, https://www.kernel.org/doc/Documentation/fb/modedb.rst

Offline

#10 2024-03-31 17:45:44

canegiallo
Member
Registered: 2016-11-18
Posts: 14

Re: Set uncommon screen resolution with an Arc 380

Thank you so much for the effort you are dedicating helping me, I owe you a favor.

Added the new KMS, both blacklist simpledrm init and video mode. So now my KMS list is:

GRUB_CMDLINE_LINUX_DEFAULT="quiet drm.edid_firmware=HDMI-1:edid/edid-l1.bin drm.edid_firmware=HDMI-A-1:edid/edid-l1.bin initcall_blacklist=simpledrm_platform_driver_init video=HDMI-A-1:1920x860@60 video=HDMI-1:1920x860@60"

Here is my dmesg update: https://pastebin.com/MKeX0nJy

And the xorg log update:

[     4.845] (--) Log file renamed from "/var/log/Xorg.pid-1192.log" to "/var/log/Xorg.0.log"
[     4.846] 
X.Org X Server 1.21.1.11
X Protocol Version 11, Revision 0
[     4.846] Current Operating System: Linux red 6.8.2-artix1-1 #1 SMP PREEMPT_DYNAMIC Wed, 27 Mar 2024 20:16:29 +0000 x86_64
[     4.846] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=03d658ef-c33d-4628-b59b-a5a485ae63f9 rw net.ifnames=0 quiet drm.edid_firmware=HDMI-1:edid/edid-l1.bin drm.edid_firmware=HDMI-A-1:edid/edid-l1.bin initcall_blacklist=simpledrm_platform_driver_init video=HDMI-A-1:1920x860@60 video=HDMI-1:1920x860@60
[     4.846]  
[     4.846] Current version of pixman: 0.43.4
[     4.846] 	Before reporting problems, check http://wiki.x.org
	to make sure that you have the latest version.
[     4.846] Markers: (--) probed, (**) from config file, (==) default setting,
	(++) from command line, (!!) notice, (II) informational,
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[     4.846] (==) Log file: "/var/log/Xorg.0.log", Time: Sun Mar 31 19:42:49 2024
[     4.848] (==) Using config directory: "/etc/X11/xorg.conf.d"
[     4.848] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[     4.849] (==) No Layout section.  Using the first Screen section.
[     4.849] (==) No screen section available. Using defaults.
[     4.849] (**) |-->Screen "Default Screen Section" (0)
[     4.849] (**) |   |-->Monitor "<default monitor>"
[     4.850] (==) No monitor specified for screen "Default Screen Section".
	Using a default monitor configuration.
[     4.850] (==) Automatically adding devices
[     4.850] (==) Automatically enabling devices
[     4.850] (==) Automatically adding GPU devices
[     4.850] (==) Automatically binding GPU devices
[     4.850] (==) Max clients allowed: 256, resource mask: 0x1fffff
[     4.850] (WW) The directory "/usr/share/fonts/misc" does not exist.
[     4.850] 	Entry deleted from font path.
[     4.852] (WW) The directory "/usr/share/fonts/Type1" does not exist.
[     4.852] 	Entry deleted from font path.
[     4.852] (WW) The directory "/usr/share/fonts/100dpi" does not exist.
[     4.852] 	Entry deleted from font path.
[     4.852] (WW) The directory "/usr/share/fonts/75dpi" does not exist.
[     4.852] 	Entry deleted from font path.
[     4.852] (==) FontPath set to:
	/usr/share/fonts/TTF,
	/usr/share/fonts/OTF
[     4.852] (==) ModulePath set to "/usr/lib/xorg/modules"
[     4.852] (II) The server relies on udev to provide the list of input devices.
	If no devices become available, reconfigure udev or disable AutoAddDevices.
[     4.852] (II) Module ABI versions:
[     4.852] 	X.Org ANSI C Emulation: 0.4
[     4.852] 	X.Org Video Driver: 25.2
[     4.852] 	X.Org XInput driver : 24.4
[     4.852] 	X.Org Server Extension : 10.0
[     4.853] (++) using VT number 7

[     4.853] (II) systemd-logind: logind integration requires -keeptty and -keeptty was not provided, disabling logind integration
[     4.854] (II) xfree86: Adding drm device (/dev/dri/card0)
[     4.854] (II) Platform probe for /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.0/0000:02:01.0/0000:03:00.0/drm/card0
[     4.862] (--) PCI:*(3@0:0:0) 8086:56a5:1849:6006 rev 5, Mem @ 0xf6000000/16777216, 0xe0000000/268435456, BIOS @ 0x????????/131072
[     4.862] (II) Open ACPI successful (/var/run/acpid.socket)
[     4.862] (II) LoadModule: "glx"
[     4.863] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[     4.872] (II) Module glx: vendor="X.Org Foundation"
[     4.872] 	compiled for 1.21.1.11, module version = 1.0.0
[     4.872] 	ABI class: X.Org Server Extension, version 10.0
[     4.872] (==) Matched intel as autoconfigured driver 0
[     4.872] (==) Matched modesetting as autoconfigured driver 1
[     4.872] (==) Matched fbdev as autoconfigured driver 2
[     4.872] (==) Matched vesa as autoconfigured driver 3
[     4.872] (==) Assigned the driver to the xf86ConfigLayout
[     4.872] (II) LoadModule: "intel"
[     4.872] (WW) Warning, couldn't open module intel
[     4.872] (EE) Failed to load module "intel" (module does not exist, 0)
[     4.872] (II) LoadModule: "modesetting"
[     4.872] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so
[     4.875] (II) Module modesetting: vendor="X.Org Foundation"
[     4.875] 	compiled for 1.21.1.11, module version = 1.21.1
[     4.875] 	Module class: X.Org Video Driver
[     4.875] 	ABI class: X.Org Video Driver, version 25.2
[     4.875] (II) LoadModule: "fbdev"
[     4.875] (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so
[     4.875] (EE) Failed to load /usr/lib/xorg/modules/drivers/fbdev_drv.so: /usr/lib/xorg/modules/drivers/fbdev_drv.so: undefined symbol: fbdevHWSave
[     4.875] (EE) Failed to load module "fbdev" (loader failed, 0)
[     4.875] (II) LoadModule: "vesa"
[     4.875] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so
[     4.876] (II) Module vesa: vendor="X.Org Foundation"
[     4.876] 	compiled for 1.21.1.4, module version = 2.6.0
[     4.876] 	Module class: X.Org Video Driver
[     4.876] 	ABI class: X.Org Video Driver, version 25.2
[     4.876] (II) modesetting: Driver for Modesetting Kernel Drivers: kms
[     4.876] (II) VESA: driver for VESA chipsets: vesa
[     4.893] (II) modeset(0): using drv /dev/dri/card0
[     4.894] (II) modeset(0): Creating default Display subsection in Screen section
	"Default Screen Section" for depth/fbbpp 24/32
[     4.894] (==) modeset(0): Depth 24, (==) framebuffer bpp 32
[     4.894] (==) modeset(0): RGB weight 888
[     4.894] (==) modeset(0): Default visual is TrueColor
[     4.894] (II) Loading sub module "glamoregl"
[     4.894] (II) LoadModule: "glamoregl"
[     4.894] (II) Loading /usr/lib/xorg/modules/libglamoregl.so
[     4.899] (II) Module glamoregl: vendor="X.Org Foundation"
[     4.899] 	compiled for 1.21.1.11, module version = 1.0.1
[     4.899] 	ABI class: X.Org ANSI C Emulation, version 0.4
[     5.193] (II) modeset(0): glamor X acceleration enabled on Mesa Intel(R) Arc(tm) A380 Graphics (DG2)
[     5.193] (II) modeset(0): glamor initialized
[     5.193] (==) modeset(0): VariableRefresh: disabled
[     5.193] (==) modeset(0): AsyncFlipSecondaries: disabled
[     5.195] (II) modeset(0): Output HDMI-1 has no monitor section
[     5.195] (II) modeset(0): Output DP-1 has no monitor section
[     5.195] (II) modeset(0): Output HDMI-2 has no monitor section
[     5.197] (II) modeset(0): EDID for output HDMI-1
[     5.197] (II) modeset(0): Manufacturer: MSR  Model: 418  Serial#: 539165720
[     5.197] (II) modeset(0): Year: 2021  Week: 23
[     5.197] (II) modeset(0): EDID Version: 1.3
[     5.197] (II) modeset(0): Digital Display Input
[     5.197] (II) modeset(0): Max Image Size [cm]: horiz.: 27  vert.: 12
[     5.197] (II) modeset(0): Gamma: 2.20
[     5.197] (II) modeset(0): DPMS capabilities: StandBy Suspend Off
[     5.197] (II) modeset(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 
[     5.197] (II) modeset(0): First detailed timing is preferred mode
[     5.197] (II) modeset(0): redX: 0.680 redY: 0.310   greenX: 0.206 greenY: 0.693
[     5.197] (II) modeset(0): blueX: 0.151 blueY: 0.055   whiteX: 0.313 whiteY: 0.329
[     5.197] (II) modeset(0): Manufacturer's mask: 0
[     5.197] (II) modeset(0): Supported standard timings:
[     5.197] (II) modeset(0): #0: hsize: 1280  vsize 720  refresh: 60  vid: 49281
[     5.197] (II) modeset(0): Supported detailed timing:
[     5.197] (II) modeset(0): clock: 110.7 MHz   Image Size:  278 x 124 mm
[     5.197] (II) modeset(0): h_active: 1920  h_sync: 1968  h_sync_end 2000 h_blank_end 2106 h_border: 0
[     5.197] (II) modeset(0): v_active: 860  v_sync: 863  v_sync_end 868 v_blanking: 876 v_border: 0
[     5.197] (II) modeset(0): Serial No: L1-20230418
[     5.197] (II) modeset(0): Monitor name: L1
[     5.197] (II) modeset(0): Ranges: V min: 56 V max: 76 Hz, H min: 30 H max: 81 kHz, PixClock max 175 MHz
[     5.197] (II) modeset(0): Number of EDID sections to follow: 1
[     5.197] (II) modeset(0): EDID (in hex):
[     5.197] (II) modeset(0): 	00ffffffffffff003672180418042320
[     5.197] (II) modeset(0): 	171f0103801b0c78ea1ec5ae4f34b126
[     5.197] (II) modeset(0): 	0e505400000081c00101010101010101
[     5.197] (II) modeset(0): 	0101010101013c2b80ba705c10303020
[     5.197] (II) modeset(0): 	3500167c1000001e000000ff004c312d
[     5.197] (II) modeset(0): 	32303233303431380a20000000fc004c
[     5.197] (II) modeset(0): 	310a20202020202020202020000000fd
[     5.197] (II) modeset(0): 	00384c1e5111000a20202020202001cc
[     5.197] (II) modeset(0): 	00000000000000000000000000000000
[     5.197] (II) modeset(0): 	00000000000000000000000000000000
[     5.197] (II) modeset(0): 	00000000000000000000000000000000
[     5.197] (II) modeset(0): 	00000000000000000000000000000000
[     5.197] (II) modeset(0): 	00000000000000000000000000000000
[     5.197] (II) modeset(0): 	00000000000000000000000000000000
[     5.197] (II) modeset(0): 	00000000000000000000000000000000
[     5.197] (II) modeset(0): 	00000000000000000000000000000000
[     5.197] (II) modeset(0): Printing probed modes for output HDMI-1
[     5.197] (II) modeset(0): Modeline "1280x720"x60.0   74.25  1280 1390 1430 1650  720 725 730 750 +hsync +vsync (45.0 kHz e)
[     5.197] (II) modeset(0): EDID for output DP-1
[     5.197] (II) modeset(0): EDID for output HDMI-2
[     5.197] (II) modeset(0): Output HDMI-1 connected
[     5.197] (II) modeset(0): Output DP-1 disconnected
[     5.197] (II) modeset(0): Output HDMI-2 disconnected
[     5.197] (II) modeset(0): Using sloppy heuristic for initial modes
[     5.197] (II) modeset(0): Output HDMI-1 using initial mode 1280x720 +0+0
[     5.197] (==) modeset(0): Using gamma correction (1.0, 1.0, 1.0)
[     5.197] (==) modeset(0): DPI set to (96, 96)
[     5.197] (II) Loading sub module "fb"
[     5.197] (II) LoadModule: "fb"
[     5.197] (II) Module "fb" already built-in
[     5.197] (II) UnloadModule: "vesa"
[     5.197] (II) Unloading vesa
[     5.220] (==) modeset(0): Backing store enabled
[     5.220] (==) modeset(0): Silken mouse enabled
[     5.360] (II) modeset(0): Initializing kms color map for depth 24, 8 bpc.
[     5.360] (==) modeset(0): DPMS enabled
[     5.360] (II) modeset(0): [DRI2] Setup complete
[     5.360] (II) modeset(0): [DRI2]   DRI driver: iris
[     5.360] (II) modeset(0): [DRI2]   VDPAU driver: va_gl
[     5.360] (II) Initializing extension Generic Event Extension
[     5.360] (II) Initializing extension SHAPE
[     5.360] (II) Initializing extension MIT-SHM
[     5.361] (II) Initializing extension XInputExtension
[     5.361] (II) Initializing extension XTEST
[     5.361] (II) Initializing extension BIG-REQUESTS
[     5.361] (II) Initializing extension SYNC
[     5.361] (II) Initializing extension XKEYBOARD
[     5.361] (II) Initializing extension XC-MISC
[     5.361] (II) Initializing extension SECURITY
[     5.361] (II) Initializing extension XFIXES
[     5.361] (II) Initializing extension RENDER
[     5.361] (II) Initializing extension RANDR
[     5.361] (II) Initializing extension COMPOSITE
[     5.361] (II) Initializing extension DAMAGE
[     5.362] (II) Initializing extension MIT-SCREEN-SAVER
[     5.362] (II) Initializing extension DOUBLE-BUFFER
[     5.362] (II) Initializing extension RECORD
[     5.362] (II) Initializing extension DPMS
[     5.362] (II) Initializing extension Present
[     5.362] (II) Initializing extension DRI3
[     5.362] (II) Initializing extension X-Resource
[     5.362] (II) Initializing extension XVideo
[     5.362] (II) Initializing extension XVideo-MotionCompensation
[     5.362] (II) Initializing extension GLX
[     5.371] (II) AIGLX: Loaded and initialized iris
[     5.371] (II) GLX: Initialized DRI2 GL provider for screen 0
[     5.371] (II) Initializing extension XFree86-VidModeExtension
[     5.371] (II) Initializing extension XFree86-DGA
[     5.371] (II) Initializing extension XFree86-DRI
[     5.371] (II) Initializing extension DRI2
[     5.371] (II) modeset(0): Damage tracking initialized
[     5.371] (II) modeset(0): Setting screen physical size to 338 x 190
[     5.444] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[     5.444] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[     5.444] (**) Power Button: Applying InputClass "system-keyboard"
[     5.444] (II) LoadModule: "libinput"
[     5.444] (II) Loading /usr/lib/xorg/modules/input/libinput_drv.so
[     5.448] (II) Module libinput: vendor="X.Org Foundation"
[     5.448] 	compiled for 1.21.1.8, module version = 1.4.0
[     5.448] 	Module class: X.Org XInput Driver
[     5.448] 	ABI class: X.Org XInput driver, version 24.4
[     5.448] (II) Using input driver 'libinput' for 'Power Button'
[     5.448] (**) Power Button: always reports core events
[     5.448] (**) Option "Device" "/dev/input/event1"
[     5.454] (II) event1  - Power Button: is tagged by udev as: Keyboard
[     5.454] (II) event1  - Power Button: device is a keyboard
[     5.454] (II) event1  - Power Button: device removed
[     5.476] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input1/event1"
[     5.476] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[     5.476] (**) Option "xkb_layout" "us"
[     5.477] (II) event1  - Power Button: is tagged by udev as: Keyboard
[     5.477] (II) event1  - Power Button: device is a keyboard
[     5.477] (II) config/udev: Adding input device Power Button (/dev/input/event0)
[     5.477] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[     5.477] (**) Power Button: Applying InputClass "system-keyboard"
[     5.477] (II) Using input driver 'libinput' for 'Power Button'
[     5.477] (**) Power Button: always reports core events
[     5.477] (**) Option "Device" "/dev/input/event0"
[     5.478] (II) event0  - Power Button: is tagged by udev as: Keyboard
[     5.478] (II) event0  - Power Button: device is a keyboard
[     5.478] (II) event0  - Power Button: device removed
[     5.490] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0/event0"
[     5.490] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 7)
[     5.490] (**) Option "xkb_layout" "us"
[     5.490] (II) event0  - Power Button: is tagged by udev as: Keyboard
[     5.490] (II) event0  - Power Button: device is a keyboard
[     5.491] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event7)
[     5.491] (II) No input driver specified, ignoring this device.
[     5.491] (II) This device may have been added with another device file.
[     5.491] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=7 (/dev/input/event9)
[     5.491] (II) No input driver specified, ignoring this device.
[     5.491] (II) This device may have been added with another device file.
[     5.492] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=8 (/dev/input/event11)
[     5.492] (II) No input driver specified, ignoring this device.
[     5.492] (II) This device may have been added with another device file.
[     5.492] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=9 (/dev/input/event13)
[     5.492] (II) No input driver specified, ignoring this device.
[     5.492] (II) This device may have been added with another device file.
[     5.492] (II) config/udev: Adding input device Kensington Expert Wireless TB Mouse (/dev/input/event16)
[     5.493] (**) Kensington Expert Wireless TB Mouse: Applying InputClass "libinput pointer catchall"
[     5.493] (**) Kensington Expert Wireless TB Mouse: Applying InputClass "system-mouse"
[     5.493] (II) Using input driver 'libinput' for 'Kensington Expert Wireless TB Mouse'
[     5.493] (**) Kensington Expert Wireless TB Mouse: always reports core events
[     5.493] (**) Option "Device" "/dev/input/event16"
[     5.494] (II) event16 - Kensington Expert Wireless TB Mouse: is tagged by udev as: Mouse Trackball
[     5.494] (II) event16 - Kensington Expert Wireless TB Mouse: device set to 400 DPI
[     5.494] (II) event16 - Kensington Expert Wireless TB Mouse: device is a pointer
[     5.494] (II) event16 - Kensington Expert Wireless TB Mouse: device removed
[     5.546] (II) libinput: Kensington Expert Wireless TB Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[     5.546] (II) libinput: Kensington Expert Wireless TB Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[     5.546] (II) libinput: Kensington Expert Wireless TB Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[     5.546] (**) Option "ScrollMethod" "button"
[     5.546] (**) Option "ScrollButton" "3"
[     5.546] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-13/3-13:1.0/0003:047D:8018.0003/input/input16/event16"
[     5.546] (II) XINPUT: Adding extended input device "Kensington Expert Wireless TB Mouse" (type: MOUSE, id 8)
[     5.546] (**) Option "AccelerationScheme" "none"
[     5.546] (**) Kensington Expert Wireless TB Mouse: (accel) selected scheme none/0
[     5.546] (**) Kensington Expert Wireless TB Mouse: (accel) acceleration factor: 2.000
[     5.546] (**) Kensington Expert Wireless TB Mouse: (accel) acceleration threshold: 4
[     5.547] (II) event16 - Kensington Expert Wireless TB Mouse: is tagged by udev as: Mouse Trackball
[     5.548] (II) event16 - Kensington Expert Wireless TB Mouse: device set to 400 DPI
[     5.548] (II) event16 - Kensington Expert Wireless TB Mouse: device is a pointer
[     5.548] (II) config/udev: Adding input device Kensington Expert Wireless TB Mouse (/dev/input/mouse0)
[     5.548] (**) Kensington Expert Wireless TB Mouse: Applying InputClass "system-mouse"
[     5.548] (II) No input driver specified, ignoring this device.
[     5.548] (II) This device may have been added with another device file.
[     5.549] (II) config/udev: Adding input device Kensington Expert Wireless TB Consumer Control (/dev/input/event17)
[     5.549] (**) Kensington Expert Wireless TB Consumer Control: Applying InputClass "libinput keyboard catchall"
[     5.549] (**) Kensington Expert Wireless TB Consumer Control: Applying InputClass "system-keyboard"
[     5.549] (II) Using input driver 'libinput' for 'Kensington Expert Wireless TB Consumer Control'
[     5.549] (**) Kensington Expert Wireless TB Consumer Control: always reports core events
[     5.549] (**) Option "Device" "/dev/input/event17"
[     5.550] (II) event17 - Kensington Expert Wireless TB Consumer Control: is tagged by udev as: Keyboard
[     5.550] (II) event17 - Kensington Expert Wireless TB Consumer Control: device is a keyboard
[     5.550] (II) event17 - Kensington Expert Wireless TB Consumer Control: device removed
[     5.570] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-13/3-13:1.0/0003:047D:8018.0003/input/input17/event17"
[     5.570] (II) XINPUT: Adding extended input device "Kensington Expert Wireless TB Consumer Control" (type: KEYBOARD, id 9)
[     5.570] (**) Option "xkb_layout" "us"
[     5.571] (II) event17 - Kensington Expert Wireless TB Consumer Control: is tagged by udev as: Keyboard
[     5.571] (II) event17 - Kensington Expert Wireless TB Consumer Control: device is a keyboard
[     5.572] (II) config/udev: Adding input device IQUNIX IQUNIX OG80 Mechanical Keyboard (/dev/input/event18)
[     5.572] (**) IQUNIX IQUNIX OG80 Mechanical Keyboard: Applying InputClass "libinput keyboard catchall"
[     5.572] (**) IQUNIX IQUNIX OG80 Mechanical Keyboard: Applying InputClass "system-keyboard"
[     5.572] (II) Using input driver 'libinput' for 'IQUNIX IQUNIX OG80 Mechanical Keyboard'
[     5.572] (**) IQUNIX IQUNIX OG80 Mechanical Keyboard: always reports core events
[     5.572] (**) Option "Device" "/dev/input/event18"
[     5.573] (II) event18 - IQUNIX IQUNIX OG80 Mechanical Keyboard: is tagged by udev as: Keyboard
[     5.573] (II) event18 - IQUNIX IQUNIX OG80 Mechanical Keyboard: device is a keyboard
[     5.573] (II) event18 - IQUNIX IQUNIX OG80 Mechanical Keyboard: device removed
[     5.583] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7:1.0/0003:05AC:024F.0001/input/input18/event18"
[     5.583] (II) XINPUT: Adding extended input device "IQUNIX IQUNIX OG80 Mechanical Keyboard" (type: KEYBOARD, id 10)
[     5.583] (**) Option "xkb_layout" "us"
[     5.584] (II) event18 - IQUNIX IQUNIX OG80 Mechanical Keyboard: is tagged by udev as: Keyboard
[     5.584] (II) event18 - IQUNIX IQUNIX OG80 Mechanical Keyboard: device is a keyboard
[     5.585] (II) config/udev: Adding input device IQUNIX IQUNIX OG80 Mechanical Keyboard (/dev/input/event19)
[     5.585] (**) IQUNIX IQUNIX OG80 Mechanical Keyboard: Applying InputClass "libinput pointer catchall"
[     5.585] (**) IQUNIX IQUNIX OG80 Mechanical Keyboard: Applying InputClass "libinput keyboard catchall"
[     5.585] (**) IQUNIX IQUNIX OG80 Mechanical Keyboard: Applying InputClass "system-keyboard"
[     5.585] (**) IQUNIX IQUNIX OG80 Mechanical Keyboard: Applying InputClass "system-mouse"
[     5.585] (II) Using input driver 'libinput' for 'IQUNIX IQUNIX OG80 Mechanical Keyboard'
[     5.585] (**) IQUNIX IQUNIX OG80 Mechanical Keyboard: always reports core events
[     5.585] (**) Option "Device" "/dev/input/event19"
[     5.586] (II) event19 - IQUNIX IQUNIX OG80 Mechanical Keyboard: is tagged by udev as: Keyboard Mouse
[     5.586] (II) event19 - IQUNIX IQUNIX OG80 Mechanical Keyboard: device is a pointer
[     5.586] (II) event19 - IQUNIX IQUNIX OG80 Mechanical Keyboard: device is a keyboard
[     5.586] (II) event19 - IQUNIX IQUNIX OG80 Mechanical Keyboard: device removed
[     5.606] (II) libinput: IQUNIX IQUNIX OG80 Mechanical Keyboard: Step value 0 was provided, libinput Fallback acceleration function is used.
[     5.606] (II) libinput: IQUNIX IQUNIX OG80 Mechanical Keyboard: Step value 0 was provided, libinput Fallback acceleration function is used.
[     5.606] (II) libinput: IQUNIX IQUNIX OG80 Mechanical Keyboard: Step value 0 was provided, libinput Fallback acceleration function is used.
[     5.606] (**) Option "ScrollMethod" "button"
[     5.606] (**) Option "ScrollButton" "3"
[     5.606] (II) libinput: IQUNIX IQUNIX OG80 Mechanical Keyboard: needs a virtual subdevice
[     5.606] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7:1.1/0003:05AC:024F.0002/input/input19/event19"
[     5.606] (II) XINPUT: Adding extended input device "IQUNIX IQUNIX OG80 Mechanical Keyboard" (type: MOUSE, id 11)
[     5.606] (**) Option "AccelerationScheme" "none"
[     5.606] (**) IQUNIX IQUNIX OG80 Mechanical Keyboard: (accel) selected scheme none/0
[     5.606] (**) IQUNIX IQUNIX OG80 Mechanical Keyboard: (accel) acceleration factor: 2.000
[     5.606] (**) IQUNIX IQUNIX OG80 Mechanical Keyboard: (accel) acceleration threshold: 4
[     5.607] (II) event19 - IQUNIX IQUNIX OG80 Mechanical Keyboard: is tagged by udev as: Keyboard Mouse
[     5.608] (II) event19 - IQUNIX IQUNIX OG80 Mechanical Keyboard: device is a pointer
[     5.608] (II) event19 - IQUNIX IQUNIX OG80 Mechanical Keyboard: device is a keyboard
[     5.608] (II) config/udev: Adding input device IQUNIX IQUNIX OG80 Mechanical Keyboard (/dev/input/mouse1)
[     5.608] (**) IQUNIX IQUNIX OG80 Mechanical Keyboard: Applying InputClass "system-keyboard"
[     5.608] (**) IQUNIX IQUNIX OG80 Mechanical Keyboard: Applying InputClass "system-mouse"
[     5.608] (II) No input driver specified, ignoring this device.
[     5.608] (II) This device may have been added with another device file.
[     5.609] (II) config/udev: Adding input device HDA Intel PCH Line Out Side (/dev/input/event14)
[     5.609] (II) No input driver specified, ignoring this device.
[     5.609] (II) This device may have been added with another device file.
[     5.609] (II) config/udev: Adding input device HDA Intel PCH Front Headphone (/dev/input/event15)
[     5.609] (II) No input driver specified, ignoring this device.
[     5.609] (II) This device may have been added with another device file.
[     5.609] (II) config/udev: Adding input device HDA Intel PCH Front Mic (/dev/input/event4)
[     5.609] (II) No input driver specified, ignoring this device.
[     5.609] (II) This device may have been added with another device file.
[     5.609] (II) config/udev: Adding input device HDA Intel PCH Rear Mic (/dev/input/event5)
[     5.609] (II) No input driver specified, ignoring this device.
[     5.609] (II) This device may have been added with another device file.
[     5.610] (II) config/udev: Adding input device HDA Intel PCH Line (/dev/input/event6)
[     5.610] (II) No input driver specified, ignoring this device.
[     5.610] (II) This device may have been added with another device file.
[     5.610] (II) config/udev: Adding input device HDA Intel PCH Line Out Front (/dev/input/event8)
[     5.610] (II) No input driver specified, ignoring this device.
[     5.610] (II) This device may have been added with another device file.
[     5.610] (II) config/udev: Adding input device HDA Intel PCH Line Out Surround (/dev/input/event10)
[     5.610] (II) No input driver specified, ignoring this device.
[     5.610] (II) This device may have been added with another device file.
[     5.611] (II) config/udev: Adding input device HDA Intel PCH Line Out CLFE (/dev/input/event12)
[     5.611] (II) No input driver specified, ignoring this device.
[     5.611] (II) This device may have been added with another device file.
[     5.611] (II) config/udev: Adding input device Eee PC WMI hotkeys (/dev/input/event3)
[     5.611] (**) Eee PC WMI hotkeys: Applying InputClass "libinput keyboard catchall"
[     5.611] (**) Eee PC WMI hotkeys: Applying InputClass "system-keyboard"
[     5.611] (II) Using input driver 'libinput' for 'Eee PC WMI hotkeys'
[     5.611] (**) Eee PC WMI hotkeys: always reports core events
[     5.611] (**) Option "Device" "/dev/input/event3"
[     5.611] (II) event3  - Eee PC WMI hotkeys: is tagged by udev as: Keyboard
[     5.611] (II) event3  - Eee PC WMI hotkeys: device is a keyboard
[     5.611] (II) event3  - Eee PC WMI hotkeys: device removed
[     5.643] (**) Option "config_info" "udev:/sys/devices/platform/eeepc-wmi/input/input3/event3"
[     5.643] (II) XINPUT: Adding extended input device "Eee PC WMI hotkeys" (type: KEYBOARD, id 12)
[     5.643] (**) Option "xkb_layout" "us"
[     5.644] (II) event3  - Eee PC WMI hotkeys: is tagged by udev as: Keyboard
[     5.644] (II) event3  - Eee PC WMI hotkeys: device is a keyboard
[     5.644] (II) config/udev: Adding input device PC Speaker (/dev/input/event2)
[     5.644] (II) No input driver specified, ignoring this device.
[     5.644] (II) This device may have been added with another device file.
[     5.660] (**) IQUNIX IQUNIX OG80 Mechanical Keyboard: Applying InputClass "libinput pointer catchall"
[     5.660] (**) IQUNIX IQUNIX OG80 Mechanical Keyboard: Applying InputClass "libinput keyboard catchall"
[     5.660] (**) IQUNIX IQUNIX OG80 Mechanical Keyboard: Applying InputClass "system-keyboard"
[     5.660] (**) IQUNIX IQUNIX OG80 Mechanical Keyboard: Applying InputClass "system-mouse"
[     5.660] (II) Using input driver 'libinput' for 'IQUNIX IQUNIX OG80 Mechanical Keyboard'
[     5.660] (**) IQUNIX IQUNIX OG80 Mechanical Keyboard: always reports core events
[     5.660] (**) Option "Device" "/dev/input/event19"
[     5.660] (II) libinput: IQUNIX IQUNIX OG80 Mechanical Keyboard: is a virtual subdevice
[     5.660] (II) libinput: IQUNIX IQUNIX OG80 Mechanical Keyboard: Step value 0 was provided, libinput Fallback acceleration function is used.
[     5.660] (II) libinput: IQUNIX IQUNIX OG80 Mechanical Keyboard: Step value 0 was provided, libinput Fallback acceleration function is used.
[     5.660] (II) libinput: IQUNIX IQUNIX OG80 Mechanical Keyboard: Step value 0 was provided, libinput Fallback acceleration function is used.
[     5.660] (**) Option "ScrollMethod" "button"
[     5.660] (**) Option "ScrollButton" "3"
[     5.660] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7:1.1/0003:05AC:024F.0002/input/input19/event19"
[     5.660] (II) XINPUT: Adding extended input device "IQUNIX IQUNIX OG80 Mechanical Keyboard" (type: KEYBOARD, id 13)
[     5.660] (**) Option "xkb_layout" "us"
[    12.657] (II) config/udev: Adding input device BJYP-L1 Device BJYP-L1-V1.09 (/dev/input/mouse3)
[    12.657] (**) BJYP-L1 Device BJYP-L1-V1.09: Applying InputClass "system-mouse"
[    12.657] (II) No input driver specified, ignoring this device.
[    12.657] (II) This device may have been added with another device file.
[    12.750] (II) config/udev: Adding input device BJYP-L1 Device BJYP-L1-V1.09 (/dev/input/event21)
[    12.750] (**) BJYP-L1 Device BJYP-L1-V1.09: Applying InputClass "libinput pointer catchall"
[    12.750] (**) BJYP-L1 Device BJYP-L1-V1.09: Applying InputClass "system-mouse"
[    12.750] (II) Using input driver 'libinput' for 'BJYP-L1 Device BJYP-L1-V1.09'
[    12.750] (**) BJYP-L1 Device BJYP-L1-V1.09: always reports core events
[    12.750] (**) Option "Device" "/dev/input/event21"
[    12.824] (II) event21 - BJYP-L1 Device BJYP-L1-V1.09: is tagged by udev as: Mouse
[    12.824] (II) event21 - BJYP-L1 Device BJYP-L1-V1.09: device is a pointer
[    12.824] (II) event21 - BJYP-L1 Device BJYP-L1-V1.09: device removed
[    12.866] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-3/3-3.3/3-3.3:1.1/0003:28E9:028A.0006/input/input21/event21"
[    12.866] (II) XINPUT: Adding extended input device "BJYP-L1 Device BJYP-L1-V1.09" (type: MOUSE, id 14)
[    12.867] (**) Option "AccelerationScheme" "none"
[    12.867] (**) BJYP-L1 Device BJYP-L1-V1.09: (accel) selected scheme none/0
[    12.867] (**) BJYP-L1 Device BJYP-L1-V1.09: (accel) acceleration factor: 2.000
[    12.867] (**) BJYP-L1 Device BJYP-L1-V1.09: (accel) acceleration threshold: 4
[    12.868] (II) event21 - BJYP-L1 Device BJYP-L1-V1.09: is tagged by udev as: Mouse
[    12.868] (II) event21 - BJYP-L1 Device BJYP-L1-V1.09: device is a pointer
[    12.869] (II) config/udev: Adding input device BJYP-L1 Device BJYP-L1-V1.09 (/dev/input/event22)
[    12.869] (II) No input driver specified, ignoring this device.
[    12.869] (II) This device may have been added with another device file.
[    12.873] (II) config/udev: Adding input device BJYP-L1 Device BJYP-L1-V1.09 (/dev/input/mouse2)
[    12.873] (II) No input driver specified, ignoring this device.
[    12.873] (II) This device may have been added with another device file.
[    13.190] (II) config/udev: Adding input device BJYP-L1 Device BJYP-L1-V1.09 (/dev/input/event20)
[    13.190] (**) BJYP-L1 Device BJYP-L1-V1.09: Applying InputClass "libinput touchscreen catchall"
[    13.190] (II) Using input driver 'libinput' for 'BJYP-L1 Device BJYP-L1-V1.09'
[    13.190] (**) BJYP-L1 Device BJYP-L1-V1.09: always reports core events
[    13.190] (**) Option "Device" "/dev/input/event20"
[    13.247] (II) event20 - BJYP-L1 Device BJYP-L1-V1.09: is tagged by udev as: Touchscreen
[    13.247] (II) event20 - BJYP-L1 Device BJYP-L1-V1.09: device is a touch device
[    13.247] (II) event20 - BJYP-L1 Device BJYP-L1-V1.09: device removed
[    13.280] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-3/3-3.3/3-3.3:1.0/0003:28E9:028A.0005/input/input23/event20"
[    13.280] (II) XINPUT: Adding extended input device "BJYP-L1 Device BJYP-L1-V1.09" (type: TOUCHSCREEN, id 15)
[    13.280] (**) Option "AccelerationScheme" "none"
[    13.280] (**) BJYP-L1 Device BJYP-L1-V1.09: (accel) selected scheme none/0
[    13.280] (**) BJYP-L1 Device BJYP-L1-V1.09: (accel) acceleration factor: 2.000
[    13.280] (**) BJYP-L1 Device BJYP-L1-V1.09: (accel) acceleration threshold: 4
[    13.281] (II) event20 - BJYP-L1 Device BJYP-L1-V1.09: is tagged by udev as: Touchscreen
[    13.281] (II) event20 - BJYP-L1 Device BJYP-L1-V1.09: device is a touch device
[    54.512] (II) event1  - Power Button: device removed
[    54.530] (II) event0  - Power Button: device removed
[    54.570] (II) event16 - Kensington Expert Wireless TB Mouse: device removed
[    54.603] (II) event17 - Kensington Expert Wireless TB Consumer Control: device removed
[    54.620] (II) event18 - IQUNIX IQUNIX OG80 Mechanical Keyboard: device removed
[    54.636] (II) event3  - Eee PC WMI hotkeys: device removed
[    54.653] (II) event19 - IQUNIX IQUNIX OG80 Mechanical Keyboard: device removed
[    54.670] (II) event21 - BJYP-L1 Device BJYP-L1-V1.09: device removed
[    54.713] (II) event20 - BJYP-L1 Device BJYP-L1-V1.09: device removed
[    54.746] (II) AIGLX: Suspending AIGLX clients for VT switch
[    57.111] (II) config/udev: removing device BJYP-L1 Device BJYP-L1-V1.09
[    57.111] (II) UnloadModule: "libinput"
[    57.221] (II) config/udev: removing device BJYP-L1 Device BJYP-L1-V1.09
[    57.221] (II) UnloadModule: "libinput"
[    67.183] (II) config/udev: Adding input device BJYP-L1 Device BJYP-L1-V1.09 (/dev/input/mouse3)
[    67.183] (**) BJYP-L1 Device BJYP-L1-V1.09: Applying InputClass "system-mouse"
[    67.183] (II) No input driver specified, ignoring this device.
[    67.183] (II) This device may have been added with another device file.
[    67.185] (II) config/udev: Adding input device BJYP-L1 Device BJYP-L1-V1.09 (/dev/input/mouse2)
[    67.185] (II) No input driver specified, ignoring this device.
[    67.185] (II) This device may have been added with another device file.
[    67.267] (II) config/udev: Adding input device BJYP-L1 Device BJYP-L1-V1.09 (/dev/input/event22)
[    67.267] (II) No input driver specified, ignoring this device.
[    67.267] (II) This device may have been added with another device file.
[    67.277] (II) config/udev: Adding input device BJYP-L1 Device BJYP-L1-V1.09 (/dev/input/event21)
[    67.277] (**) BJYP-L1 Device BJYP-L1-V1.09: Applying InputClass "libinput pointer catchall"
[    67.277] (**) BJYP-L1 Device BJYP-L1-V1.09: Applying InputClass "system-mouse"
[    67.277] (II) Using input driver 'libinput' for 'BJYP-L1 Device BJYP-L1-V1.09'
[    67.277] (**) BJYP-L1 Device BJYP-L1-V1.09: always reports core events
[    67.277] (**) Option "Device" "/dev/input/event21"
[    67.337] (II) event21 - BJYP-L1 Device BJYP-L1-V1.09: is tagged by udev as: Mouse
[    67.338] (II) event21 - BJYP-L1 Device BJYP-L1-V1.09: device is a pointer
[    67.338] (II) event21 - BJYP-L1 Device BJYP-L1-V1.09: device removed
[    67.380] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-3/3-3.3/3-3.3:1.1/0003:28E9:028A.0009/input/input25/event21"
[    67.380] (II) XINPUT: Adding extended input device "BJYP-L1 Device BJYP-L1-V1.09" (type: MOUSE, id 14)
[    67.380] (**) Option "AccelerationScheme" "none"
[    67.380] (**) BJYP-L1 Device BJYP-L1-V1.09: (accel) selected scheme none/0
[    67.380] (**) BJYP-L1 Device BJYP-L1-V1.09: (accel) acceleration factor: 2.000
[    67.380] (**) BJYP-L1 Device BJYP-L1-V1.09: (accel) acceleration threshold: 4
[    67.434] (II) config/udev: Adding input device BJYP-L1 Device BJYP-L1-V1.09 (/dev/input/event20)
[    67.434] (**) BJYP-L1 Device BJYP-L1-V1.09: Applying InputClass "libinput touchscreen catchall"
[    67.434] (II) Using input driver 'libinput' for 'BJYP-L1 Device BJYP-L1-V1.09'
[    67.434] (**) BJYP-L1 Device BJYP-L1-V1.09: always reports core events
[    67.434] (**) Option "Device" "/dev/input/event20"
[    67.493] (II) event20 - BJYP-L1 Device BJYP-L1-V1.09: is tagged by udev as: Touchscreen
[    67.493] (II) event20 - BJYP-L1 Device BJYP-L1-V1.09: device is a touch device
[    67.493] (II) event20 - BJYP-L1 Device BJYP-L1-V1.09: device removed
[    67.520] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-3/3-3.3/3-3.3:1.0/0003:28E9:028A.0008/input/input24/event20"
[    67.520] (II) XINPUT: Adding extended input device "BJYP-L1 Device BJYP-L1-V1.09" (type: TOUCHSCREEN, id 15)
[    67.520] (**) Option "AccelerationScheme" "none"
[    67.520] (**) BJYP-L1 Device BJYP-L1-V1.09: (accel) selected scheme none/0
[    67.520] (**) BJYP-L1 Device BJYP-L1-V1.09: (accel) acceleration factor: 2.000
[    67.520] (**) BJYP-L1 Device BJYP-L1-V1.09: (accel) acceleration threshold: 4

Still can't get the correct screen resolution. sad

Offline

#11 2024-03-31 21:51:06

seth
Member
Registered: 2012-09-03
Posts: 52,199

Re: Set uncommon screen resolution with an Arc 380

Remove xf86-video-vesa (though I'd not bet on that you don't want to use that driver)
Also xf86-video-fbdev, it looks broken anyway?

[     4.875] (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so
[     4.875] (EE) Failed to load /usr/lib/xorg/modules/drivers/fbdev_drv.so: /usr/lib/xorg/modules/drivers/fbdev_drv.so: undefined symbol: fbdevHWSave
[     4.875] (EE) Failed to load module "fbdev" (loader failed, 0)

The proper output name for the kernel commandline  is HDMI-A-1

Also

[    3.085641] nvidia: module verification failed: signature and/or required key missing - tainting kernel
[    3.085642] nvidia: module license taints kernel.
[    3.451927] nvidia-nvlink: Nvlink Core is being initialized, major device number 236
[    3.451933] NVRM: No NVIDIA GPU found.

the nvidia drivers.

[    5.259664] i915 0000:03:00.0: [drm] User-defined mode not supported: "1920x860": 60 110680 1920 1968 2000 2106 860 863 868 876 0x68 0x5
[    5.261555] i915 0000:03:00.0: [drm] User-defined mode not supported: "1920x860": 60 110680 1920 1968 2000 2106 860 863 868 876 0x68 0x5

Can you switch the resolution after settign the edid after the boot (but before starting any display server), https://wiki.archlinux.org/title/Kernel … s_and_EDID ?
Where does that edid file come from? Windows?

Please elaborate on

When I connect it to the iGPU (Intel Iris Pro II) its native resolution is detected egregiously; however, if I connect it to the GPU (Intel Arc 380) the only resolution provided is 1280x720. I can only connect it via HDMI.

There's only one GPU in that system according to dmesg and the xorg log - can you extract the edid from the IIPII system (you can just copy the file from /sys/class/drm) and if you look at it w/ edid-decode, is it less bogus?

Offline

#12 2024-04-01 00:21:59

canegiallo
Member
Registered: 2016-11-18
Posts: 14

Re: Set uncommon screen resolution with an Arc 380

Can you switch the resolution after settign the edid after the boot (but before starting any display server), https://wiki.archlinux.org/title/Kernel … s_and_EDID ?

I am not able to switch the resolution before starting any display server. However, while Grub screen gets a 1920x1080 resolution, then the rest of the buffer gets 1024x768 (I know those infos since the monitor tells me the actual resolution and also because I see bigger fonts and stretches).

Yes I am actually forcing the edid via KMS and also through mkinitcpio; using HDMI-1 and HDMI-A-1 both because the first is the way X11 calls my monitor and the second is the way Wayland calls it.

From mkinitcpio.conf:

MODULES=(i915)
FILES="/usr/lib/firmware/edid/edid-l1.bin"

(and then `mkinitcpio -P`).

From /etc/grub:

drm.edid_firmware=HDMI-1:edid/edid-l1.bin drm.edid_firmware=HDMI-A-1:edid/edid-l1.bin

(and then `grub-mkconfig -o /boot/grub/grub.cfg`).

Where does that edid file come from? Windows?

Yes, I managed to get the complete edid infos (and edid) through Windows 10 using EnTech Monitor Asset Manager. Maybe I could have used the edid.bin I can get from get-edid, but I have got more infor through this software (example: screen size and factory modesetting).

Elaborate on: When I connect it to the iGPU (Intel Iris Pro II) its native resolution is detected egregiously; however, if I connect it to the GPU (Intel Arc 380) the only resolution provided is 1280x720. I can only connect it via HDMI.

Before connecting the Arc 380 GPU I was using the processor internal cpu; since it is an i5 5675c, it has got Iris Pro II graphics. While using those graphics (and no special edid or no configurations) the monitor resolution is perfect, a native 1920x860. If I connect the monitor to the dedicated GPU, the Arc 380, 1720x860 on Wayland (or 1920x1080 added with xrandr on X11) are the only resolutions I can get.

There's only one GPU in that system according to dmesg and the xorg log

True, that is because if I use the dedicated GPU, I set the bios to use only the PCI connected GPU for display; I am doing this to avoid some other messes.

can you extract the edid from the IIPII system (you can just copy the file from /sys/class/drm)

Yes I could, it was my first try extracting an edid file. However it didn't work tho... so I tried the painful thing of getting Windows 10 and extracting the edid with more complete info; infact the first time I got the edid from the IIPII, parsing it through parse-edid I had only a portion of the infos I could get through said Windows software.

Here is the edid.bin I extracted on Linux with Intel Iris Pro II with get-edid:

$ cat edid.bin | parse-edid
Checksum Correct

Section "Monitor"
        Identifier "L1"
        ModelName "L1"
        VendorName "MSR"
        # Monitor Manufactured week 23 of 2021
        # EDID version 1.3
        # Digital Display
        DisplaySize 270 120
        Gamma 2.20
        Option "DPMS" "true"
        Horizsync 30-81
        VertRefresh 56-76
        # Maximum pixel clock is 170MHz
        #Not giving standard mode: 1280x720, 60Hz

        #Extension block found. Parsing...
        Modeline        "Mode 2" +hsync +vsync interlace
        Modeline        "Mode 0" +hsync +vsync 
        Modeline        "Mode 1" 74.250 1280 1390 1420 1650 720 725 730 750 +hsync +vsync
        Option "PreferredMode" "Mode 2"
EndSection

Here is the different edid-l1.bin I have got from Windows 10, but parsed through parse-edid on Linux:

$ cat edid-l1.bin | parse-edid
Checksum Correct

Section "Monitor"
        Identifier "L1"
        ModelName "L1"
        VendorName "MSR"
        # Monitor Manufactured week 23 of 2021
        # EDID version 1.3
        # Digital Display
        DisplaySize 270 120
        Gamma 2.20
        Option "DPMS" "true"
        Horizsync 30-81
        VertRefresh 56-76
        # Maximum pixel clock is 170MHz
        #Not giving standard mode: 1280x720, 60Hz

        #Extension block found. Parsing...
I only know about extension blocks of type 02h. PLEASE email me!
Something strange happened. Please contact the author,
Matthew Kern at <pyrophobicman@gmail.com>

(Yes indeed I contacted already Matthew Kern with the interesting infos).

Also, here are the logs I have got now when I loaded the edid.bin (the one I got from the IIPII):
dmesg: https://pastebin.com/raw/nmD37Cia
xorg: https://pastebin.com/LkJvuPt4

And here are the logs I have got after when I loaded the edid-l1.bin (the one got from Windows):
dmesg: https://pastebin.com/m67PH4ee
xorg: https://pastebin.com/wSRyN2yU

(As you can see in both, I followed your suggestions removing unuseful nvidia drivers, the xf86 vesa and the xf86 fbdev.

Still I cannot set the native resolution, but hopefully those infos can get us some news (and hopes) smile

Offline

#13 2024-04-01 07:34:20

seth
Member
Registered: 2012-09-03
Posts: 52,199

Re: Set uncommon screen resolution with an Arc 380

Don't use parse-edid, it doesn't handle DTDs
Windows

edid-decode (hex):

00 ff ff ff ff ff ff 00 36 72 18 04 18 04 23 20
17 1f 01 03 80 1b 0c 78 ea 1e c5 ae 4f 34 b1 26
0e 50 54 00 00 00 81 c0 01 01 01 01 01 01 01 01
01 01 01 01 01 01 3c 2b 80 ba 70 5c 10 30 30 20
35 00 16 7c 10 00 00 1e 00 00 00 ff 00 4c 31 2d
32 30 32 33 30 34 31 38 0a 20 00 00 00 fc 00 4c
31 0a 20 20 20 20 20 20 20 20 20 20 00 00 00 fd
00 38 4c 1e 51 11 00 0a 20 20 20 20 20 20 01 cc

00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

----------------

Block 0, Base EDID:
  EDID Structure Version & Revision: 1.3
  Vendor & Product Identification:
    Manufacturer: MSR
    Model: 1048
    Serial Number: 539165720
    Made in: week 23 of 2021
  Basic Display Parameters & Features:
    Digital display
    Maximum image size: 27 cm x 12 cm
    Gamma: 2.20
    DPMS levels: Standby Suspend Off
    RGB color display
    First detailed timing is the preferred timing
  Color Characteristics:
    Red  : 0.6796, 0.3095
    Green: 0.2060, 0.6933
    Blue : 0.1513, 0.0546
    White: 0.3134, 0.3291
  Established Timings I & II: none
  Standard Timings:
    DMT 0x55:  1280x720    60.000000 Hz  16:9     45.000 kHz     74.250000 MHz
  Detailed Timing Descriptors:
    DTD 1:  1920x860    59.993842 Hz  96:43    52.555 kHz    110.680000 MHz (278 mm x 124 mm)
                 Hfront   48 Hsync  32 Hback  106 Hpol P
                 Vfront    3 Vsync   5 Vback    8 Vpol P
    Display Product Serial Number: 'L1-20230418'
    Display Product Name: 'L1'
    Display Range Limits:
      Monitor ranges (GTF): 56-76 Hz V, 30-81 kHz H, max dotclock 170 MHz
  Extension blocks: 1
Checksum: 0xcc

----------------

Block 1, Unknown EDID Extension Block 0x00:
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 '................'
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 '................'
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 '................'
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 '................'
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 '................'
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 '................'
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 '................'
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 '................'
Checksum: 0x00

Straight from the iris system

edid-decode (hex):

00 ff ff ff ff ff ff 00 36 72 18 04 18 04 23 20
17 1f 01 03 80 1b 0c 78 ea 1e c5 ae 4f 34 b1 26
0e 50 54 00 00 00 81 c0 01 01 01 01 01 01 01 01
01 01 01 01 01 01 3c 2b 80 ba 70 5c 10 30 30 20
35 00 16 7c 10 00 00 1e 00 00 00 ff 00 4c 31 2d
32 30 32 33 30 34 31 38 0a 20 00 00 00 fc 00 4c
31 0a 20 20 20 20 20 20 20 20 20 20 00 00 00 fd
00 38 4c 1e 51 11 00 0a 20 20 20 20 20 20 01 cc

02 03 1a f1 41 84 23 09 7f 07 67 03 0c 00 10 00
38 2d 83 01 00 00 e3 05 03 01 01 1d 80 18 71 1c
16 20 58 2c 25 00 06 44 21 00 00 9e 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f3

----------------

Block 0, Base EDID:
  EDID Structure Version & Revision: 1.3
  Vendor & Product Identification:
    Manufacturer: MSR
    Model: 1048
    Serial Number: 539165720
    Made in: week 23 of 2021
  Basic Display Parameters & Features:
    Digital display
    Maximum image size: 27 cm x 12 cm
    Gamma: 2.20
    DPMS levels: Standby Suspend Off
    RGB color display
    First detailed timing is the preferred timing
  Color Characteristics:
    Red  : 0.6796, 0.3095
    Green: 0.2060, 0.6933
    Blue : 0.1513, 0.0546
    White: 0.3134, 0.3291
  Established Timings I & II: none
  Standard Timings:
    DMT 0x55:  1280x720    60.000000 Hz  16:9     45.000 kHz     74.250000 MHz
  Detailed Timing Descriptors:
    DTD 1:  1920x860    59.993842 Hz  96:43    52.555 kHz    110.680000 MHz (278 mm x 124 mm)
                 Hfront   48 Hsync  32 Hback  106 Hpol P
                 Vfront    3 Vsync   5 Vback    8 Vpol P
    Display Product Serial Number: 'L1-20230418'
    Display Product Name: 'L1'
    Display Range Limits:
      Monitor ranges (GTF): 56-76 Hz V, 30-81 kHz H, max dotclock 170 MHz
  Extension blocks: 1
Checksum: 0xcc

----------------

Block 1, CTA-861 Extension Block:
  Revision: 3
  Underscans IT Video Formats by default
  Basic audio support
  Supports YCbCr 4:4:4
  Supports YCbCr 4:2:2
  Native detailed modes: 1
  Video Data Block:
    VIC   4:  1280x720    60.000000 Hz  16:9     45.000 kHz     74.250000 MHz (native)
  Audio Data Block:
    Linear PCM:
      Max channels: 2
      Supported sample rates (kHz): 192 176.4 96 88.2 48 44.1 32
      Supported sample sizes (bits): 24 20 16
  Vendor-Specific Data Block (HDMI), OUI 00-0C-03:
    Source physical address: 1.0.0.0
    DC_36bit
    DC_30bit
    DC_Y444
    Maximum TMDS clock: 225 MHz
  Speaker Allocation Data Block:
    FL/FR - Front Left/Right
  Colorimetry Data Block:
    xvYCC601
    xvYCC709
  Detailed Timing Descriptors:
    DTD 2:  1920x1080i  60.000000 Hz  16:9     33.750 kHz     74.250000 MHz (518 mm x 324 mm)
                 Hfront   88 Hsync  44 Hback  148 Hpol P
                 Vfront    2 Vsync   5 Vback   15 Vpol P Vfront +0.5 Odd Field
                 Vfront    2 Vsync   5 Vback   15 Vpol P Vback  +0.5 Even Field
Checksum: 0xf3

Try to install xf86-video-intel and select the iris DRI, https://wiki.archlinux.org/title/Intel_ … ecent_GPUs
If that accepts the edid modeline it's a bogus filter in the KMS drivers (again)

Offline

#14 2024-04-01 11:23:00

canegiallo
Member
Registered: 2016-11-18
Posts: 14

Re: Set uncommon screen resolution with an Arc 380

Try to install xf86-video-intel and select the iris DRI, https://wiki.archlinux.org/title/Intel_ … ecent_GPUs
If that accepts the edid modeline it's a bogus filter in the KMS drivers (again)

Did it various times before,but xf86-video-intel gives this error message:

[   517.715] (WW) intel(0): Unknown chipset

I tried with various xorg combinations, but nothing changes; i found also this intel arc a750 on void linux from a year ago which says the same thing about driver intel + arc gives Unknown chipset warning and then some errors.

Also a peek from the note on xf86-video-intel from Arch Wiki: Intel Graphics:

This package is generally not recommended

The xf86-video-intel driver does not have proper support for Gen 11 and newer hardware

Here is one of the xorg log I have got using xf86-video-intel:

[   517.684] (--) Log file renamed from "/var/log/Xorg.pid-19512.log" to "/var/log/Xorg.0.log"
[   517.685] X.Org X Server 1.21.1.11
X Protocol Version 11, Revision 0
[   517.685] Current Operating System: Linux red 6.8.2-artix1-1 #1 SMP PREEMPT_DYNAMIC Wed, 27 Mar 2024 20:16:29 +0000 x86_64
[   517.685] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=03d658ef-c33d-4628-b59b-a5a485ae63f9 rw net.ifnames=0 quiet drm.edid_firmware=HDMI-1:edid/edid.bin drm.edid_firmware=HDMI-A-1:edid/edid.bin initcall_blacklist=simpledrm_platform_driver_init video=HDMI-1:1920x860@60 video=HDMI-A-1:1920x860@60 i915.force_probe=03:00.0
[   517.685]  
[   517.685] Current version of pixman: 0.43.4
[   517.685] 	Before reporting problems, check http://wiki.x.org
	to make sure that you have the latest version.
[   517.685] Markers: (--) probed, (**) from config file, (==) default setting,
	(++) from command line, (!!) notice, (II) informational,
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[   517.685] (==) Log file: "/var/log/Xorg.0.log", Time: Mon Apr  1 12:49:17 2024
[   517.685] (==) Using config directory: "/etc/X11/xorg.conf.d"
[   517.685] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[   517.685] (==) No Layout section.  Using the first Screen section.
[   517.685] (==) No screen section available. Using defaults.
[   517.685] (**) |-->Screen "Default Screen Section" (0)
[   517.685] (**) |   |-->Monitor "<default monitor>"
[   517.685] (==) No device specified for screen "Default Screen Section".
	Using the first device section listed.
[   517.685] (**) |   |-->Device "Intel Graphics"
[   517.685] (==) No monitor specified for screen "Default Screen Section".
	Using a default monitor configuration.
[   517.685] (==) Automatically adding devices
[   517.685] (==) Automatically enabling devices
[   517.685] (==) Automatically adding GPU devices
[   517.685] (==) Automatically binding GPU devices
[   517.685] (==) Max clients allowed: 256, resource mask: 0x1fffff
[   517.685] (WW) The directory "/usr/share/fonts/misc" does not exist.
[   517.685] 	Entry deleted from font path.
[   517.685] (WW) The directory "/usr/share/fonts/Type1" does not exist.
[   517.685] 	Entry deleted from font path.
[   517.685] (WW) The directory "/usr/share/fonts/100dpi" does not exist.
[   517.685] 	Entry deleted from font path.
[   517.685] (WW) The directory "/usr/share/fonts/75dpi" does not exist.
[   517.685] 	Entry deleted from font path.
[   517.685] (==) FontPath set to:
	/usr/share/fonts/TTF,
	/usr/share/fonts/OTF
[   517.685] (==) ModulePath set to "/usr/lib/xorg/modules"
[   517.685] (II) The server relies on udev to provide the list of input devices.
	If no devices become available, reconfigure udev or disable AutoAddDevices.
[   517.685] (II) Module ABI versions:
[   517.685] 	X.Org ANSI C Emulation: 0.4
[   517.685] 	X.Org Video Driver: 25.2
[   517.685] 	X.Org XInput driver : 24.4
[   517.685] 	X.Org Server Extension : 10.0
[   517.686] (++) using VT number 7

[   517.686] (II) systemd-logind: logind integration requires -keeptty and -keeptty was not provided, disabling logind integration
[   517.687] (II) xfree86: Adding drm device (/dev/dri/card0)
[   517.687] (II) Platform probe for /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.0/0000:02:01.0/0000:03:00.0/drm/card0
[   517.699] (--) PCI:*(3@0:0:0) 8086:56a5:1849:6006 rev 5, Mem @ 0xf6000000/16777216, 0xe0000000/268435456, BIOS @ 0x????????/131072
[   517.699] (II) Open ACPI successful (/var/run/acpid.socket)
[   517.699] (II) LoadModule: "glx"
[   517.699] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[   517.700] (II) Module glx: vendor="X.Org Foundation"
[   517.700] 	compiled for 1.21.1.11, module version = 1.0.0
[   517.700] 	ABI class: X.Org Server Extension, version 10.0
[   517.700] (II) LoadModule: "intel"
[   517.700] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[   517.701] (II) Module intel: vendor="X.Org Foundation"
[   517.701] 	compiled for 1.21.1.7, module version = 2.99.917
[   517.701] 	Module class: X.Org Video Driver
[   517.701] 	ABI class: X.Org Video Driver, version 25.2
[   517.701] (II) intel: Driver for Intel(R) Integrated Graphics Chipsets:
	i810, i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G,
	915G, E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM,
	Pineview G, 965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33,
	GM45, 4 Series, G45/G43, Q45/Q43, G41, B43
[   517.701] (II) intel: Driver for Intel(R) HD Graphics
[   517.701] (II) intel: Driver for Intel(R) Iris(TM) Graphics
[   517.701] (II) intel: Driver for Intel(R) Iris(TM) Pro Graphics
[   517.715] (II) intel(0): Using Kernel Mode Setting driver: i915, version 1.6.0 20230929
[   517.715] (II) intel(0): SNA compiled from 2.99.917-923-gb74b67f0
[   517.715] (WW) intel(0): Unknown chipset
[   517.715] (--) intel(0): CPU: x86-64, sse2, sse3, ssse3, sse4.1, sse4.2, avx, avx2; using a maximum of 4 threads
[   517.715] (II) intel(0): Creating default Display subsection in Screen section
	"Default Screen Section" for depth/fbbpp 24/32
[   517.715] (EE) intel(0): Given depth (24) is not supported by the Intel driver and this chipset.
[   517.730] (II) UnloadModule: "intel"
[   517.730] (EE) Screen(s) found, but none have a usable configuration.
[   517.730] (EE) 
Fatal server error:
[   517.730] (EE) no screens found(EE) 
[   517.730] (EE) 
Please consult the The X.Org Foundation support 
	 at http://wiki.x.org
 for help. 
[   517.730] (EE) Please also check the log file at "/var/log/Xorg.0.log" for additional information.
[   517.730] (EE) 
[   517.798] (EE) Server terminated with error (1). Closing log file.

And here is the most minimal xorg configuration I used to start the graphic server (I tried different and longer combinations tho):

Section "Device"
  Identifier  "Intel Graphics"
  	Driver      "intel"
	Option      "DRI" "iris"             # DRI3 is now default 
#	Option      "AccelMethod"  "sna" # default
EndSection

Addendum: if I connect the Arc 380 to a standard resolution monitor, it works perfectly; the problem is still with uncommon screen resolution (saying it to give most informations I can).

Last edited by canegiallo (2024-04-01 11:24:28)

Offline

#15 2024-04-01 13:16:12

seth
Member
Registered: 2012-09-03
Posts: 52,199

Re: Set uncommon screen resolution with an Arc 380

Ok, so the intel DDX no longer supports your chip (or rather vv wink and the kms driver - great sad

echo 6 | sudo tee /sys/module/drm/parameters/debug
dmesg -w
# replug the output

This is gonna produce a lot of output and will hopefully tell whether and why the drm doesn't like the mode and allow research and complaints on https://gitlab.freedesktop.org/drm/intel/-/issues hmm

Offline

#16 2024-04-01 14:09:57

canegiallo
Member
Registered: 2016-11-18
Posts: 14

Re: Set uncommon screen resolution with an Arc 380

Here we are!

[ 1845.632919] i915 0000:03:00.0: [drm:icp_irq_handler [i915]] hotplug event received, stat 0x00020000, dig 0x000080a0, pins 0x00000020, long 0x00000020
[ 1845.633441] i915 0000:03:00.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 5 - cnt: 10
[ 1845.634009] i915 0000:03:00.0: [drm:i915_hotplug_work_func [i915]] running encoder hotplug functions
[ 1845.634204] i915 0000:03:00.0: [drm:i915_hotplug_work_func [i915]] Connector HDMI-A-1 (pin 5) received hotplug event. (retry 0)
[ 1845.634368] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
[ 1845.634536] i915 0000:03:00.0: [drm:intel_hotplug_detect_connector [i915]] [CONNECTOR:236:HDMI-A-1] status updated from connected to disconnected (epoch counter 1->2)
[ 1845.634749] i915 0000:03:00.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:236:HDMI-A-1] generating connector hotplug event
[ 1845.658017] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:HDMI-A-1]
[ 1845.658025] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
[ 1845.658145] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:HDMI-A-1] disconnected
[ 1845.658149] i915 0000:03:00.0: [drm:drm_edid_connector_update] [CONNECTOR:236:HDMI-A-1] EDID changed, epoch counter 3
[ 1845.672215] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:246:DP-1]
[ 1845.672223] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
[ 1845.672357] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:246:DP-1] disconnected
[ 1845.672372] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:HDMI-A-2]
[ 1845.672376] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
[ 1845.672508] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:HDMI-A-2] disconnected
[ 1845.672528] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:HDMI-A-1]
[ 1845.672532] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
[ 1845.672662] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:HDMI-A-1] disconnected
[ 1845.689037] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:246:DP-1]
[ 1845.689047] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
[ 1845.689194] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:246:DP-1] disconnected
[ 1845.689214] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:HDMI-A-2]
[ 1845.689219] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
[ 1845.689342] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:HDMI-A-2] disconnected
[ 1846.387788] i915 0000:03:00.0: [drm:intel_atomic_check [i915]] [CONNECTOR:236:HDMI-A-1] Limiting display bpp to 24 (EDID bpp 0, max requested bpp 36, max platform bpp 36)
[ 1846.387948] i915 0000:03:00.0: [drm:intel_hdmi_compute_clock [i915]] picking 8 bpc for HDMI output (pipe bpp: 24)
[ 1846.388066] i915 0000:03:00.0: [drm:intel_atomic_check [i915]] [CRTC:80:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0
[ 1846.388203] i915 0000:03:00.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:235:DDI B/PHY B] [CRTC:80:pipe A]
[ 1846.388303] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.active (expected yes, found no)
[ 1846.388421] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in has_hdmi_sink (expected yes, found no)
[ 1846.388547] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in has_infoframe (expected yes, found no)
[ 1846.388670] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in infoframes.enable (expected 0x00000019, found 0x00000000)
[ 1846.388790] i915 0000:03:00.0: [drm:pipe_config_infoframe_mismatch [i915]] fastset requirement not met in avi infoframe
[ 1846.388903] i915 0000:03:00.0: [drm:pipe_config_infoframe_mismatch [i915]] expected:
[ 1846.389026] i915 0000:03:00.0: HDMI infoframe: Auxiliary Video Information (AVI), version 2, length 13
[ 1846.389028] i915 0000:03:00.0:     colorspace: RGB
[ 1846.389028] i915 0000:03:00.0:     scan mode: Underscan
[ 1846.389030] i915 0000:03:00.0:     colorimetry: No Data
[ 1846.389030] i915 0000:03:00.0:     picture aspect: No Data
[ 1846.389031] i915 0000:03:00.0:     active aspect: Same as Picture
[ 1846.389032] i915 0000:03:00.0:     itc: No Data
[ 1846.389033] i915 0000:03:00.0:     extended colorimetry: xvYCC 601
[ 1846.389034] i915 0000:03:00.0:     quantization range: Full
[ 1846.389034] i915 0000:03:00.0:     nups: Unknown Non-uniform Scaling
[ 1846.389035] i915 0000:03:00.0:     video code: 0
[ 1846.389036] i915 0000:03:00.0:     ycc quantization range: Limited
[ 1846.389037] i915 0000:03:00.0:     hdmi content type: Graphics
[ 1846.389038] i915 0000:03:00.0:     pixel repeat: 0
[ 1846.389038] i915 0000:03:00.0:     bar top 0, bottom 0, left 0, right 0
[ 1846.389040] i915 0000:03:00.0: [drm:pipe_config_infoframe_mismatch [i915]] found:
[ 1846.389155] i915 0000:03:00.0: [drm:pipe_config_infoframe_mismatch [i915]] fastset requirement not met in spd infoframe
[ 1846.389272] i915 0000:03:00.0: [drm:pipe_config_infoframe_mismatch [i915]] expected:
[ 1846.389388] i915 0000:03:00.0: HDMI infoframe: Source Product Description (SPD), version 1, length 25
[ 1846.389389] i915 0000:03:00.0:     vendor: Intel
[ 1846.389390] i915 0000:03:00.0:     product: Discrete gfx
[ 1846.389391] i915 0000:03:00.0:     source device information: PC General (0x9)
[ 1846.389392] i915 0000:03:00.0: [drm:pipe_config_infoframe_mismatch [i915]] found:
[ 1846.389509] i915 0000:03:00.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset
[ 1846.389638] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0x3 -> 0x1 (total dbuf slices 0xf), mbus joined? no->no
[ 1846.389745] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [CRTC:80:pipe A] dbuf slices 0x3 -> 0x0, ddb (0 - 2048) -> (0 - 0), active pipes 0x1 -> 0x0
[ 1846.389869] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb (   0 - 1976) -> (   0 -    0), size 1976 ->    0
[ 1846.389985] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] ddb (1976 - 2048) -> (   0 -    0), size   72 ->    0
[ 1846.390105] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A]   level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm ->  wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
[ 1846.390220] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A]   lines    1,   3,   4,   5,   9,  11,  17,  21,   0,   0,    0 ->    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0
[ 1846.390327] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A]  blocks   16,  49,  65,  81, 145, 177, 273, 337,  30,   0,    0 ->    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0
[ 1846.390439] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb   19,  55,  73,  91, 161, 196, 302, 372,  31,   0,    0 ->    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0
[ 1846.390553] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A]   level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm ->  wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
[ 1846.390666] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A]   lines    2,   3,   4,   5,   9,  11,  17,  21,   0,   0,    0 ->    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0
[ 1846.390781] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A]  blocks    6,  10,  13,  16,  28,  34,  52,  64,  20,   0,    0 ->    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0
[ 1846.390888] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] min_ddb    8,  12,  16,  19,  32,  39,  59,  72,  21,   0,    0 ->    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0
[ 1846.391009] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] [CRTC:80:pipe A] data rate 0 num active planes 0
[ 1846.391154] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 38000 required 0
[ 1846.391273] i915 0000:03:00.0: [drm:intel_modeset_calc_cdclk [i915]] Can change cdclk via squashing
[ 1846.391387] i915 0000:03:00.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 163200 kHz, actual 163200 kHz
[ 1846.391502] i915 0000:03:00.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 0, actual 0
[ 1846.391620] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] [CRTC:80:pipe A] enable: yes [modeset]
[ 1846.391738] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] active: no, output_types: HDMI (0x40), output format: RGB, sink format: RGB
[ 1846.391853] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 24, dithering: 0
[ 1846.391973] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>
[ 1846.392082] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
[ 1846.392192] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0
[ 1846.392301] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0
[ 1846.392411] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0
[ 1846.392521] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0
[ 1846.392635] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: 1, vmax vblank: 0
[ 1846.392754] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] requested mode: "": 60 138500 1920 1968 2000 2080 1080 1083 1088 1111 0x0 0x9
[ 1846.392877] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "": 60 138500 1920 1968 2000 2080 1080 1083 1088 1111 0x0 0x9
[ 1846.393001] i915 0000:03:00.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=138500, hd=1920 hb=1920-2080 hs=1968-2000 ht=2080, vd=1080 vb=1080-1111 vs=1083-1088 vt=1111, flags=0x9
[ 1846.393126] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "1920x1080": 60 138500 1920 1968 2000 2080 1080 1083 1088 1111 0x40 0x9
[ 1846.393251] i915 0000:03:00.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=138500, hd=1920 hb=1920-2080 hs=1968-2000 ht=2080, vd=1080 vb=1080-1111 vs=1083-1088 vt=1111, flags=0x9
[ 1846.393376] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] port clock: 138500, pipe src: 1920x1080+0+0, pixel rate 138500
[ 1846.393499] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] linetime: 121, ips linetime: 0
[ 1846.393622] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
[ 1846.393745] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no
[ 1846.393869] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0
[ 1846.393992] i915 0000:03:00.0: [drm:intel_dpll_dump_hw_state [i915]] dpll_hw_state: dpll: 0x21d04, dpll_md: 0x18000000, fp0: 0xc801cf8, fp1: 0x2b000440
[ 1846.394113] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x40000001 gamma_enable: 0 csc_enable: 0
[ 1846.394237] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 1024 entries
[ 1846.394356] i915 0000:03:00.0: [drm:ilk_dump_csc [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000
[ 1846.394499] i915 0000:03:00.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
[ 1846.394635] i915 0000:03:00.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
[ 1846.394751] i915 0000:03:00.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
[ 1846.394866] i915 0000:03:00.0: [drm:ilk_dump_csc [i915]] output csc: post offsets: 0x0000 0x0000 0x0000
[ 1846.394991] i915 0000:03:00.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
[ 1846.395113] i915 0000:03:00.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
[ 1846.395236] i915 0000:03:00.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
[ 1846.395355] i915 0000:03:00.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
[ 1846.395466] i915 0000:03:00.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000
[ 1846.395577] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:258] 1920x1080 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: no
[ 1846.395700] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]]    rotation: 0x1, scaler: -1, scaling_filter: 0
[ 1846.395815] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no
[ 1846.395936] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no
[ 1846.396058] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no
[ 1846.396176] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no
[ 1846.396291] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:cursor A] fb: [FB:262] 256x256 format = AR24 little-endian (0x34325241) modifier = 0x0, visible: no
[ 1846.396410] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]]    rotation: 0x1, scaler: -1, scaling_filter: 0
[ 1846.396541] i915 0000:03:00.0: [drm:intel_audio_codec_disable [i915]] [CONNECTOR:236:HDMI-A-1][ENCODER:235:DDI B/PHY B] Disable audio codec on [CRTC:80:pipe A]
[ 1846.423052] i915 0000:03:00.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
[ 1846.439848] i915 0000:03:00.0: [drm:intel_disable_transcoder [i915]] disabling pipe A
[ 1846.457809] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B
[ 1846.457977] i915 0000:03:00.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:31:plane 1A]
[ 1846.458127] i915 0000:03:00.0: [drm:intel_set_cdclk [i915]] Changing CDCLK to 163200 kHz, VCO 1305600 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
[ 1846.458271] i915 0000:03:00.0: [drm:intel_set_cdclk [i915]] aud_ts_cdclk set to M=60, N=408
[ 1846.458404] i915 0000:03:00.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:235:DDI B/PHY B]
[ 1846.458537] i915 0000:03:00.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:245:DDI D/PHY D]
[ 1846.458671] i915 0000:03:00.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:247:DP-MST A]
[ 1846.458806] i915 0000:03:00.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:248:DP-MST B]
[ 1846.458940] i915 0000:03:00.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:249:DP-MST C]
[ 1846.459074] i915 0000:03:00.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:250:DP-MST D]
[ 1846.459207] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x3
[ 1846.459400] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
[ 1846.459585] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_A
[ 1846.459751] i915 0000:03:00.0: [drm:verify_connector_state [i915]] [CONNECTOR:236:HDMI-A-1]
[ 1846.459870] i915 0000:03:00.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:80:pipe A]
[ 1846.460020] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
[ 1846.460036] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
[ 1846.460160] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
[ 1846.460285] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
[ 1846.460409] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in output_types (expected 0x00000040, found 0x00000000)
[ 1846.460534] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
[ 1846.460658] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 1920, found 0)
[ 1846.460782] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 2080, found 0)
[ 1846.460906] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 1920, found 0)
[ 1846.461030] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 2080, found 0)
[ 1846.461181] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 1968, found 0)
[ 1846.461325] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2000, found 0)
[ 1846.461452] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1080, found 0)
[ 1846.461610] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1080, found 0)
[ 1846.461740] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1083, found 0)
[ 1846.461863] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1088, found 0)
[ 1846.461987] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1111, found 0)
[ 1846.462110] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1111, found 0)
[ 1846.462235] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 1920, found 0)
[ 1846.462359] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 2080, found 0)
[ 1846.462483] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 1920, found 0)
[ 1846.462607] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 2080, found 0)
[ 1846.462734] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 1968, found 0)
[ 1846.462858] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2000, found 0)
[ 1846.462983] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1080, found 0)
[ 1846.463106] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1080, found 0)
[ 1846.463230] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1083, found 0)
[ 1846.463354] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1088, found 0)
[ 1846.463479] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1111, found 0)
[ 1846.463603] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1111, found 0)
[ 1846.463727] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
[ 1846.463850] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.flags (1) (expected 1, found 0)
[ 1846.463975] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
[ 1846.464099] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in pipe_bpp (expected 24, found 0)
[ 1846.464223] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 138500, found 0)
[ 1846.464347] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 138500, found 0)
[ 1846.464515] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in port_clock (expected 138500, found 0)
[ 1846.464643] i915 0000:03:00.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset
[ 1846.464796] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] [CRTC:80:pipe A] enable: no [modeset]
[ 1846.464919] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [NOFB], visible: no
[ 1846.465043] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no
[ 1846.465167] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no
[ 1846.465291] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no
[ 1846.465414] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no
[ 1846.465538] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:cursor A] fb: [FB:262] 256x256 format = AR24 little-endian (0x34325241) modifier = 0x0, visible: no
[ 1846.465663] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]]    rotation: 0x1, scaler: -1, scaling_filter: 0
[ 1846.465802] i915 0000:03:00.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:235:DDI B/PHY B]
[ 1846.465920] i915 0000:03:00.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:245:DDI D/PHY D]
[ 1846.466034] i915 0000:03:00.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:247:DP-MST A]
[ 1846.466157] i915 0000:03:00.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:248:DP-MST B]
[ 1846.466264] i915 0000:03:00.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:249:DP-MST C]
[ 1846.466370] i915 0000:03:00.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:250:DP-MST D]
[ 1846.466473] i915 0000:03:00.0: [drm:verify_connector_state [i915]] [CONNECTOR:236:HDMI-A-1]
[ 1846.466633] i915 0000:03:00.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:80:pipe A]
[ 1846.466799] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
[ 1846.466824] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
[ 1846.466844] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
[ 1846.515685] i915 0000:03:00.0: [drm:i915_gem_open [i915]] 
[ 1850.403025] i915 0000:03:00.0: [drm:icp_irq_handler [i915]] hotplug event received, stat 0x00020000, dig 0x000080a0, pins 0x00000020, long 0x00000020
[ 1850.403540] i915 0000:03:00.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 5 - cnt: 10
[ 1850.404074] i915 0000:03:00.0: [drm:i915_hotplug_work_func [i915]] running encoder hotplug functions
[ 1850.404630] i915 0000:03:00.0: [drm:i915_hotplug_work_func [i915]] Connector HDMI-A-1 (pin 5) received hotplug event. (retry 0)
[ 1850.405165] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
[ 1850.405846] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
[ 1850.406291] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
[ 1850.406944] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
[ 1850.407422] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
[ 1850.407436] i915 0000:03:00.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
[ 1850.407928] i915 0000:03:00.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
[ 1850.409359] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
[ 1850.409372] i915 0000:03:00.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
[ 1851.414502] i915 0000:03:00.0: [drm:i915_hotplug_work_func [i915]] running encoder hotplug functions
[ 1851.415049] i915 0000:03:00.0: [drm:i915_hotplug_work_func [i915]] Connector HDMI-A-1 (pin 5) received hotplug event. (retry 1)
[ 1851.415583] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
[ 1851.416965] i915 0000:03:00.0: [drm:drm_edid_load_firmware] [CONNECTOR:236:HDMI-A-1] Loaded external firmware EDID "edid/edid.bin"
[ 1851.417015] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:236:HDMI-A-1] HDMI: DVI dual 0, max TMDS clock 225000 kHz
[ 1851.417031] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:236:HDMI-A-1] HDMI sink does deep color 30.
[ 1851.417043] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:236:HDMI-A-1] HDMI sink does deep color 36.
[ 1851.417053] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:236:HDMI-A-1] Assigning HDMI sink color depth as 12 bpc.
[ 1851.417065] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:236:HDMI-A-1] HDMI sink does YCRCB444 in deep color.
[ 1851.417079] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:236:HDMI-A-1] ELD monitor L1
[ 1851.417092] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:236:HDMI-A-1] HDMI: latency present 0 0, video latency 0 0, audio latency 0 0
[ 1851.417106] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:236:HDMI-A-1] ELD size 28, SAD count 1
[ 1851.417308] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0040 w(1)
[ 1851.417803] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
[ 1851.418435] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0040 w(1)
[ 1851.418919] i915 0000:03:00.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID:  (err -6)
[ 1851.418975] i915 0000:03:00.0: [drm:intel_hotplug_detect_connector [i915]] [CONNECTOR:236:HDMI-A-1] status updated from disconnected to connected (epoch counter 3->4)
[ 1851.419512] i915 0000:03:00.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:236:HDMI-A-1] generating connector hotplug event
[ 1851.435948] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:HDMI-A-1]
[ 1851.435958] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
[ 1851.436868] i915 0000:03:00.0: [drm:drm_edid_load_firmware] [CONNECTOR:236:HDMI-A-1] Loaded external firmware EDID "edid/edid.bin"
[ 1851.436878] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:236:HDMI-A-1] HDMI: DVI dual 0, max TMDS clock 225000 kHz
[ 1851.436882] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:236:HDMI-A-1] HDMI sink does deep color 30.
[ 1851.436885] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:236:HDMI-A-1] HDMI sink does deep color 36.
[ 1851.436887] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:236:HDMI-A-1] Assigning HDMI sink color depth as 12 bpc.
[ 1851.436890] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:236:HDMI-A-1] HDMI sink does YCRCB444 in deep color.
[ 1851.436893] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:236:HDMI-A-1] ELD monitor L1
[ 1851.436896] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:236:HDMI-A-1] HDMI: latency present 0 0, video latency 0 0, audio latency 0 0
[ 1851.436899] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:236:HDMI-A-1] ELD size 28, SAD count 1
[ 1851.437068] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0040 w(1)
[ 1851.437175] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
[ 1851.437445] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0040 w(1)
[ 1851.437550] i915 0000:03:00.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID:  (err -6)
[ 1851.437604] i915 0000:03:00.0: [drm] User-defined mode not supported: "1920x860": 60 110680 1920 1968 2000 2106 860 863 868 876 0x68 0x5
[ 1851.437606] [drm:drm_mode_debug_printmodeline] Modeline "1920x860": 60 110680 1920 1968 2000 2106 860 863 868 876 0x68 0x5
[ 1851.437611] [drm:drm_mode_prune_invalid] Not using 1920x860 mode: CLOCK_RANGE
[ 1851.437613] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080i": 60 74250 1920 2008 2052 2200 1080 1084 1094 1125 0x40 0x15
[ 1851.437617] [drm:drm_mode_prune_invalid] Not using 1920x1080i mode: NO_INTERLACE
[ 1851.437619] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080i": 60 74176 1920 2008 2052 2200 1080 1084 1094 1125 0x40 0x15
[ 1851.437622] [drm:drm_mode_prune_invalid] Not using 1920x1080i mode: NO_INTERLACE
[ 1851.437625] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:HDMI-A-1] probed modes :
[ 1851.437628] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
[ 1851.437631] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
[ 1851.437634] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74176 1280 1390 1430 1650 720 725 730 750 0x40 0x5
[ 1851.437654] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:246:DP-1]
[ 1851.437657] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
[ 1851.437792] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:246:DP-1] disconnected
[ 1851.437804] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:HDMI-A-2]
[ 1851.437807] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
[ 1851.437919] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:HDMI-A-2] disconnected
[ 1851.437936] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:HDMI-A-1]
[ 1851.437939] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
[ 1851.438791] i915 0000:03:00.0: [drm:drm_edid_load_firmware] [CONNECTOR:236:HDMI-A-1] Loaded external firmware EDID "edid/edid.bin"
[ 1851.438799] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:236:HDMI-A-1] HDMI: DVI dual 0, max TMDS clock 225000 kHz
[ 1851.438802] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:236:HDMI-A-1] HDMI sink does deep color 30.
[ 1851.438805] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:236:HDMI-A-1] HDMI sink does deep color 36.
[ 1851.438807] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:236:HDMI-A-1] Assigning HDMI sink color depth as 12 bpc.
[ 1851.438810] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:236:HDMI-A-1] HDMI sink does YCRCB444 in deep color.
[ 1851.438813] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:236:HDMI-A-1] ELD monitor L1
[ 1851.438816] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:236:HDMI-A-1] HDMI: latency present 0 0, video latency 0 0, audio latency 0 0
[ 1851.438819] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:236:HDMI-A-1] ELD size 28, SAD count 1
[ 1851.438987] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0040 w(1)
[ 1851.439104] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
[ 1851.439384] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0040 w(1)
[ 1851.439505] i915 0000:03:00.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID:  (err -6)
[ 1851.439561] i915 0000:03:00.0: [drm] User-defined mode not supported: "1920x860": 60 110680 1920 1968 2000 2106 860 863 868 876 0x68 0x5
[ 1851.439564] [drm:drm_mode_debug_printmodeline] Modeline "1920x860": 60 110680 1920 1968 2000 2106 860 863 868 876 0x68 0x5
[ 1851.439569] [drm:drm_mode_prune_invalid] Not using 1920x860 mode: CLOCK_RANGE
[ 1851.439571] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080i": 60 74250 1920 2008 2052 2200 1080 1084 1094 1125 0x40 0x15
[ 1851.439575] [drm:drm_mode_prune_invalid] Not using 1920x1080i mode: NO_INTERLACE
[ 1851.439578] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080i": 60 74176 1920 2008 2052 2200 1080 1084 1094 1125 0x40 0x15
[ 1851.439582] [drm:drm_mode_prune_invalid] Not using 1920x1080i mode: NO_INTERLACE
[ 1851.439585] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:HDMI-A-1] probed modes :
[ 1851.439588] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
[ 1851.439591] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
[ 1851.439595] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74176 1280 1390 1430 1650 720 725 730 750 0x40 0x5
[ 1851.439781] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:246:DP-1]
[ 1851.439785] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
[ 1851.439914] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:246:DP-1] disconnected
[ 1851.439924] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:HDMI-A-2]
[ 1851.439927] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
[ 1851.440052] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:HDMI-A-2] disconnected
[ 1852.196548] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
[ 1852.196580] [drm:drm_mode_setcrtc] [CONNECTOR:236:HDMI-A-1]
[ 1852.196665] i915 0000:03:00.0: [drm:intel_hdmi_compute_clock [i915]] picking 8 bpc for HDMI output (pipe bpp: 24)
[ 1852.197257] i915 0000:03:00.0: [drm:intel_atomic_check [i915]] [CRTC:80:pipe A] hw max bpp: 36, pipe bpp: 24, dithering: 0
[ 1852.197860] i915 0000:03:00.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:235:DDI B/PHY B] [CRTC:80:pipe A]
[ 1852.198362] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
[ 1852.198922] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.active (expected no, found yes)
[ 1852.199480] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
[ 1852.200040] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
[ 1852.200597] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000040)
[ 1852.201192] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
[ 1852.201326] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 1920)
[ 1852.201471] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 2080)
[ 1852.201615] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 1920)
[ 1852.201759] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 2080)
[ 1852.201903] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 1968)
[ 1852.202045] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2000)
[ 1852.202186] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1080)
[ 1852.202330] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1080)
[ 1852.202470] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1083)
[ 1852.202594] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1088)
[ 1852.202718] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1111)
[ 1852.202841] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1111)
[ 1852.202965] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 1920)
[ 1852.203089] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 2080)
[ 1852.203213] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 1920)
[ 1852.203336] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 2080)
[ 1852.203460] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 1968)
[ 1852.203584] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2000)
[ 1852.203709] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1080)
[ 1852.203832] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1080)
[ 1852.203956] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1083)
[ 1852.204079] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1088)
[ 1852.204203] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1111)
[ 1852.204327] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1111)
[ 1852.204473] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
[ 1852.204610] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.flags (1) (expected 0, found 1)
[ 1852.204733] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
[ 1852.204860] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in has_hdmi_sink (expected no, found yes)
[ 1852.204988] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in has_infoframe (expected no, found yes)
[ 1852.205116] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 24)
[ 1852.205244] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 138500)
[ 1852.205372] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 138500)
[ 1852.205499] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in port_clock (expected 0, found 138500)
[ 1852.205627] i915 0000:03:00.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in infoframes.enable (expected 0x00000000, found 0x00000019)
[ 1852.205755] i915 0000:03:00.0: [drm:pipe_config_infoframe_mismatch [i915]] fastset requirement not met in avi infoframe
[ 1852.205882] i915 0000:03:00.0: [drm:pipe_config_infoframe_mismatch [i915]] expected:
[ 1852.206008] i915 0000:03:00.0: [drm:pipe_config_infoframe_mismatch [i915]] found:
[ 1852.206134] i915 0000:03:00.0: HDMI infoframe: Auxiliary Video Information (AVI), version 2, length 13
[ 1852.206136] i915 0000:03:00.0:     colorspace: RGB
[ 1852.206137] i915 0000:03:00.0:     scan mode: Underscan
[ 1852.206138] i915 0000:03:00.0:     colorimetry: No Data
[ 1852.206139] i915 0000:03:00.0:     picture aspect: No Data
[ 1852.206140] i915 0000:03:00.0:     active aspect: Same as Picture
[ 1852.206141] i915 0000:03:00.0:     itc: No Data
[ 1852.206142] i915 0000:03:00.0:     extended colorimetry: xvYCC 601
[ 1852.206143] i915 0000:03:00.0:     quantization range: Full
[ 1852.206144] i915 0000:03:00.0:     nups: Unknown Non-uniform Scaling
[ 1852.206145] i915 0000:03:00.0:     video code: 0
[ 1852.206145] i915 0000:03:00.0:     ycc quantization range: Limited
[ 1852.206146] i915 0000:03:00.0:     hdmi content type: Graphics
[ 1852.206147] i915 0000:03:00.0:     pixel repeat: 0
[ 1852.206148] i915 0000:03:00.0:     bar top 0, bottom 0, left 0, right 0
[ 1852.206149] i915 0000:03:00.0: [drm:pipe_config_infoframe_mismatch [i915]] fastset requirement not met in spd infoframe
[ 1852.206275] i915 0000:03:00.0: [drm:pipe_config_infoframe_mismatch [i915]] expected:
[ 1852.206401] i915 0000:03:00.0: [drm:pipe_config_infoframe_mismatch [i915]] found:
[ 1852.206528] i915 0000:03:00.0: HDMI infoframe: Source Product Description (SPD), version 1, length 25
[ 1852.206529] i915 0000:03:00.0:     vendor: Intel
[ 1852.206530] i915 0000:03:00.0:     product: Discrete gfx
[ 1852.206531] i915 0000:03:00.0:     source device information: PC General (0x9)
[ 1852.206533] i915 0000:03:00.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset
[ 1852.206675] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0x1 -> 0x3 (total dbuf slices 0xf), mbus joined? no->no
[ 1852.206792] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [CRTC:80:pipe A] dbuf slices 0x0 -> 0x3, ddb (0 - 0) -> (0 - 2048), active pipes 0x0 -> 0x1
[ 1852.206915] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb (   0 -    0) -> (   0 - 1976), size    0 -> 1976
[ 1852.207032] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] ddb (   0 -    0) -> (1976 - 2048), size    0 ->   72
[ 1852.207148] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A]   level  wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm
[ 1852.207265] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A]   lines    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0 ->    1,   3,   4,   5,   9,  11,  17,  21,   0,   0,    0
[ 1852.207382] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A]  blocks    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0 ->   16,  49,  65,  81, 145, 177, 273, 337,  30,   0,    0
[ 1852.207500] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0 ->   19,  55,  73,  91, 161, 196, 302, 372,  31,   0,    0
[ 1852.207619] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] [CRTC:80:pipe A] data rate 554000 num active planes 1
[ 1852.207747] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 38000 required 554
[ 1852.207882] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] No SAGV, using single QGV point 0
[ 1852.208016] i915 0000:03:00.0: [drm:intel_plane_calc_min_cdclk [i915]] [PLANE:31:plane 1A] min cdclk (69250 kHz) > [CRTC:80:pipe A] min cdclk (0 kHz)
[ 1852.208132] i915 0000:03:00.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (10821 kHz) > old min cdclk (0 kHz)
[ 1852.208248] i915 0000:03:00.0: [drm:intel_modeset_calc_cdclk [i915]] Can change cdclk via squashing
[ 1852.208362] i915 0000:03:00.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 204000 kHz, actual 204000 kHz
[ 1852.208476] i915 0000:03:00.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 0, actual 0
[ 1852.208593] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] [CRTC:80:pipe A] enable: yes [modeset]
[ 1852.208717] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: HDMI (0x40), output format: RGB, sink format: RGB
[ 1852.208845] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 24, dithering: 0
[ 1852.208972] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>
[ 1852.209099] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
[ 1852.209225] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0
[ 1852.209352] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0
[ 1852.209478] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0
[ 1852.209605] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] audio: 1, infoframes: 1, infoframes enabled: 0x19
[ 1852.209732] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] GCP: 0x0
[ 1852.209859] i915 0000:03:00.0: HDMI infoframe: Auxiliary Video Information (AVI), version 2, length 13
[ 1852.209861] i915 0000:03:00.0:     colorspace: RGB
[ 1852.209862] i915 0000:03:00.0:     scan mode: Underscan
[ 1852.209863] i915 0000:03:00.0:     colorimetry: No Data
[ 1852.209864] i915 0000:03:00.0:     picture aspect: No Data
[ 1852.209864] i915 0000:03:00.0:     active aspect: Same as Picture
[ 1852.209865] i915 0000:03:00.0:     itc: No Data
[ 1852.209866] i915 0000:03:00.0:     extended colorimetry: xvYCC 601
[ 1852.209867] i915 0000:03:00.0:     quantization range: Full
[ 1852.209868] i915 0000:03:00.0:     nups: Unknown Non-uniform Scaling
[ 1852.209869] i915 0000:03:00.0:     video code: 0
[ 1852.209870] i915 0000:03:00.0:     ycc quantization range: Limited
[ 1852.209871] i915 0000:03:00.0:     hdmi content type: Graphics
[ 1852.209871] i915 0000:03:00.0:     pixel repeat: 0
[ 1852.209872] i915 0000:03:00.0:     bar top 0, bottom 0, left 0, right 0
[ 1852.209874] i915 0000:03:00.0: HDMI infoframe: Source Product Description (SPD), version 1, length 25
[ 1852.209875] i915 0000:03:00.0:     vendor: Intel
[ 1852.209876] i915 0000:03:00.0:     product: Discrete gfx
[ 1852.209876] i915 0000:03:00.0:     source device information: PC General (0x9)
[ 1852.209878] ELD: 10 00 06 00 62 10 00 01 00 00 00 00 00 00 00 00
[ 1852.209879] ELD: 36 72 18 04 4c 31 09 7f 07 00 00 00
[ 1852.209880] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: 1, vmax vblank: 0
[ 1852.210007] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] requested mode: "": 60 138500 1920 1968 2000 2080 1080 1083 1088 1111 0x0 0x9
[ 1852.210136] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "": 60 138500 1920 1968 2000 2080 1080 1083 1088 1111 0x0 0x9
[ 1852.210264] i915 0000:03:00.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=138500, hd=1920 hb=1920-2080 hs=1968-2000 ht=2080, vd=1080 vb=1080-1111 vs=1083-1088 vt=1111, flags=0x9
[ 1852.210392] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "1920x1080": 60 138500 1920 1968 2000 2080 1080 1083 1088 1111 0x40 0x9
[ 1852.210520] i915 0000:03:00.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=138500, hd=1920 hb=1920-2080 hs=1968-2000 ht=2080, vd=1080 vb=1080-1111 vs=1083-1088 vt=1111, flags=0x9
[ 1852.210648] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] port clock: 138500, pipe src: 1920x1080+0+0, pixel rate 138500
[ 1852.210776] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] linetime: 121, ips linetime: 0
[ 1852.210903] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
[ 1852.211029] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no
[ 1852.211165] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0
[ 1852.211301] i915 0000:03:00.0: [drm:intel_dpll_dump_hw_state [i915]] dpll_hw_state: dpll: 0x21d04, dpll_md: 0x18000000, fp0: 0xc801cf8, fp1: 0x2b000440
[ 1852.211411] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x40000001 gamma_enable: 0 csc_enable: 0
[ 1852.211531] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 1024 entries
[ 1852.211647] i915 0000:03:00.0: [drm:ilk_dump_csc [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000
[ 1852.211773] i915 0000:03:00.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
[ 1852.211900] i915 0000:03:00.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
[ 1852.212026] i915 0000:03:00.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
[ 1852.212152] i915 0000:03:00.0: [drm:ilk_dump_csc [i915]] output csc: post offsets: 0x0000 0x0000 0x0000
[ 1852.212280] i915 0000:03:00.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
[ 1852.212406] i915 0000:03:00.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
[ 1852.212534] i915 0000:03:00.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
[ 1852.212660] i915 0000:03:00.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
[ 1852.212787] i915 0000:03:00.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000
[ 1852.212914] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:258] 1920x1080 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
[ 1852.213043] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]]    rotation: 0x1, scaler: -1, scaling_filter: 0
[ 1852.213170] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]]    src: 1920.000000x1080.000000+0.000000+0.000000 dst: 1920x1080+0+0
[ 1852.213299] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no
[ 1852.213426] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no
[ 1852.213553] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no
[ 1852.213680] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no
[ 1852.213807] i915 0000:03:00.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:cursor A] fb: [NOFB], visible: no
[ 1852.213956] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_A
[ 1852.214136] i915 0000:03:00.0: [drm:intel_set_cdclk [i915]] Changing CDCLK to 204000 kHz, VCO 1305600 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
[ 1852.214263] i915 0000:03:00.0: [drm:intel_set_cdclk [i915]] aud_ts_cdclk set to M=60, N=510
[ 1852.214378] i915 0000:03:00.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:235:DDI B/PHY B]
[ 1852.214501] i915 0000:03:00.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:245:DDI D/PHY D]
[ 1852.214613] i915 0000:03:00.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:247:DP-MST A]
[ 1852.214730] i915 0000:03:00.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:248:DP-MST B]
[ 1852.214849] i915 0000:03:00.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:249:DP-MST C]
[ 1852.214967] i915 0000:03:00.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:250:DP-MST D]
[ 1852.215086] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x3
[ 1852.215315] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B
[ 1852.216033] i915 0000:03:00.0: [drm:intel_enable_transcoder [i915]] enabling pipe A
[ 1852.217037] i915 0000:03:00.0: [drm:intel_fbc_update [i915]] reserved 17694720 bytes of contiguous stolen space for FBC, limit: 1
[ 1852.217174] i915 0000:03:00.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:31:plane 1A]
[ 1852.233769] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x3
[ 1852.233975] i915 0000:03:00.0: [drm:intel_audio_codec_enable [i915]] [CONNECTOR:236:HDMI-A-1][ENCODER:235:DDI B/PHY B] Enable audio codec on [CRTC:80:pipe A], 28 bytes ELD
[ 1852.250476] i915 0000:03:00.0: [drm:audio_config_hdmi_pixel_clock [i915]] HDMI audio pixel clock setting for 138500 not found, falling back to defaults
[ 1852.250621] i915 0000:03:00.0: [drm:audio_config_hdmi_pixel_clock [i915]] Configuring HDMI audio for pixel clock 25200 (0x00010000)
[ 1852.250751] i915 0000:03:00.0: [drm:hsw_hdmi_audio_config_update.isra.0 [i915]] using automatic N
[ 1852.251330] i915 0000:03:00.0: [drm:audio_config_hdmi_pixel_clock [i915]] HDMI audio pixel clock setting for 138500 not found, falling back to defaults
[ 1852.251507] i915 0000:03:00.0: [drm:audio_config_hdmi_pixel_clock [i915]] Configuring HDMI audio for pixel clock 25200 (0x00010000)
[ 1852.251675] i915 0000:03:00.0: [drm:hsw_hdmi_audio_config_update.isra.0 [i915]] using automatic N
[ 1852.262851] i915 0000:03:00.0: [drm:verify_connector_state [i915]] [CONNECTOR:236:HDMI-A-1]
[ 1852.263008] i915 0000:03:00.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:80:pipe A]
[ 1852.264685] i915 0000:03:00.0: [drm:audio_config_hdmi_pixel_clock [i915]] HDMI audio pixel clock setting for 138500 not found, falling back to defaults
[ 1852.264851] i915 0000:03:00.0: [drm:audio_config_hdmi_pixel_clock [i915]] Configuring HDMI audio for pixel clock 25200 (0x00010000)
[ 1852.265000] i915 0000:03:00.0: [drm:hsw_hdmi_audio_config_update.isra.0 [i915]] using automatic N
[ 1852.283882] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
[ 1852.283915] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
[ 1852.283936] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
[ 1853.147794] usb 3-3: USB disconnect, device number 7
[ 1853.147799] usb 3-3.3: USB disconnect, device number 8
[ 1853.238964] i915 0000:03:00.0: [drm:i915_gem_open [i915]] 
[ 1853.239294] i915 0000:03:00.0: [drm:i915_gem_open [i915]] 
[ 1862.015240] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A]   level  wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm
[ 1862.015390] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A]   lines    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0 ->    2,   3,   4,   5,   9,  11,  17,  21,   0,   0,    0
[ 1862.015532] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A]  blocks    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0 ->    6,  10,  13,  16,  28,  34,  52,  64,  20,   0,    0
[ 1862.015665] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] min_ddb    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0 ->    8,  12,  16,  19,  32,  39,  59,  72,  21,   0,    0
[ 1862.747793] usb 3-3: new high-speed USB device number 9 using xhci_hcd
[ 1862.889067] usb 3-3: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=85.38
[ 1862.889083] usb 3-3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 1862.889089] usb 3-3: Product: USB2.0 Hub
[ 1862.890491] hub 3-3:1.0: USB hub found
[ 1862.890759] hub 3-3:1.0: 4 ports detected
[ 1863.174451] usb 3-3.3: new full-speed USB device number 10 using xhci_hcd
[ 1863.265485] usb 3-3.3: config 1 interface 0 altsetting 0 has 2 endpoint descriptors, different from the interface descriptor's value: 1
[ 1863.266734] usb 3-3.3: New USB device found, idVendor=28e9, idProduct=028a, bcdDevice= 1.13
[ 1863.266748] usb 3-3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1863.266754] usb 3-3.3: Product: BJYP-L1-V1.09
[ 1863.266758] usb 3-3.3: Manufacturer: BJYP-L1 Device
[ 1863.266762] usb 3-3.3: SerialNumber: GD32F1X0-V3.0.0-4b5c6de
[ 1863.280496] input: BJYP-L1 Device BJYP-L1-V1.09 as /devices/pci0000:00/0000:00:14.0/usb3/3-3/3-3.3/3-3.3:1.0/0003:28E9:028A.000B/input/input27
[ 1863.280637] hid-multitouch 0003:28E9:028A.000B: input,hiddev98,hidraw4: USB HID v1.10 Device [BJYP-L1 Device BJYP-L1-V1.09] on usb-0000:00:14.0-3.3/input0
[ 1863.281663] input: BJYP-L1 Device BJYP-L1-V1.09 as /devices/pci0000:00/0000:00:14.0/usb3/3-3/3-3.3/3-3.3:1.1/0003:28E9:028A.000C/input/input28
[ 1863.281734] hid-generic 0003:28E9:028A.000C: input,hidraw5: USB HID v1.10 Mouse [BJYP-L1 Device BJYP-L1-V1.09] on usb-0000:00:14.0-3.3/input1
[ 1863.282606] input: BJYP-L1 Device BJYP-L1-V1.09 as /devices/pci0000:00/0000:00:14.0/usb3/3-3/3-3.3/3-3.3:1.2/0003:28E9:028A.000D/input/input29
[ 1863.282651] hid-generic 0003:28E9:028A.000D: input,hidraw6: USB HID v1.10 Device [BJYP-L1 Device BJYP-L1-V1.09] on usb-0000:00:14.0-3.3/input2
[ 1863.299975] i915 0000:03:00.0: [drm:i915_gem_open [i915]] 
[ 1863.300360] i915 0000:03:00.0: [drm:i915_gem_open [i915]] 

Offline

#17 2024-04-01 14:40:25

seth
Member
Registered: 2012-09-03
Posts: 52,199

Re: Set uncommon screen resolution with an Arc 380

[ 1851.437604] i915 0000:03:00.0: [drm] User-defined mode not supported: "1920x860": 60 110680 1920 1968 2000 2106 860 863 868 876 0x68 0x5
[ 1851.437606] [drm:drm_mode_debug_printmodeline] Modeline "1920x860": 60 110680 1920 1968 2000 2106 860 863 868 876 0x68 0x5
[ 1851.437611] [drm:drm_mode_prune_invalid] Not using 1920x860 mode: CLOCK_RANGE

Which, according to Mrs Picht (Math, 1st & 2nd grade), doesn't check out:

    DTD 1:  1920x860    59.993842 Hz  96:43    52.555 kHz    110.680000 MHz (278 mm x 124 mm)
                 Hfront   48 Hsync  32 Hback  106 Hpol P
                 Vfront    3 Vsync   5 Vback    8 Vpol P
    Display Product Serial Number: 'L1-20230418'
    Display Product Name: 'L1'
    Display Range Limits:
      Monitor ranges (GTF): 56-76 Hz V, 30-81 kHz H, max dotclock 170 MHz

110.6 < 170
30 < 52.55 < 81
56 < 59.9 < 76

The problem will be around

[ 1851.438987] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0040 w(1)
[ 1851.439104] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
[ 1851.439384] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0040 w(1)
[ 1851.439505] i915 0000:03:00.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID:  (err -6)

you're not getting those on the iris chip?

Are you using the latest linux-firmware package?
You could try your luck w/ https://aur.archlinux.org/packages/linux-drm-tip-git and https://aur.archlinux.org/packages/linux-firmware-git first …

Offline

#18 2024-04-01 17:50:56

canegiallo
Member
Registered: 2016-11-18
Posts: 14

Re: Set uncommon screen resolution with an Arc 380

Installed the linux-firmware-git, but nothing changed. :}/

Here is the log of the replug of the IIPII

[ 1847.423478] usb 3-3: USB disconnect, device number 7
[ 1847.423483] usb 3-3.3: USB disconnect, device number 8
[ 1857.201080] usb 3-3: new high-speed USB device number 9 using xhci_hcd
[ 1857.342459] usb 3-3: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=85.38
[ 1857.342474] usb 3-3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 1857.342481] usb 3-3: Product: USB2.0 Hub
[ 1857.348418] hub 3-3:1.0: USB hub found
[ 1857.348673] hub 3-3:1.0: 4 ports detected
[ 1857.627831] usb 3-3.3: new full-speed USB device number 10 using xhci_hcd
[ 1857.718690] usb 3-3.3: config 1 interface 0 altsetting 0 has 2 endpoint descriptors, different from the interface descriptor's value: 1
[ 1857.719475] usb 3-3.3: New USB device found, idVendor=28e9, idProduct=028a, bcdDevice= 1.13
[ 1857.719489] usb 3-3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1857.719496] usb 3-3.3: Product: BJYP-L1-V1.09
[ 1857.719500] usb 3-3.3: Manufacturer: BJYP-L1 Device
[ 1857.719504] usb 3-3.3: SerialNumber: GD32F1X0-V3.0.0-4b5c6de
[ 1857.733447] input: BJYP-L1 Device BJYP-L1-V1.09 as /devices/pci0000:00/0000:00:14.0/usb3/3-3/3-3.3/3-3.3:1.0/0003:28E9:028A.000B/input/input31
[ 1857.733598] hid-multitouch 0003:28E9:028A.000B: input,hiddev98,hidraw4: USB HID v1.10 Device [BJYP-L1 Device BJYP-L1-V1.09] on usb-0000:00:14.0-3.3/input0
[ 1857.734493] input: BJYP-L1 Device BJYP-L1-V1.09 as /devices/pci0000:00/0000:00:14.0/usb3/3-3/3-3.3/3-3.3:1.1/0003:28E9:028A.000C/input/input32
[ 1857.734545] hid-generic 0003:28E9:028A.000C: input,hidraw5: USB HID v1.10 Mouse [BJYP-L1 Device BJYP-L1-V1.09] on usb-0000:00:14.0-3.3/input1
[ 1857.735312] input: BJYP-L1 Device BJYP-L1-V1.09 as /devices/pci0000:00/0000:00:14.0/usb3/3-3/3-3.3/3-3.3:1.2/0003:28E9:028A.000D/input/input33
[ 1857.735366] hid-generic 0003:28E9:028A.000D: input,hidraw6: USB HID v1.10 Device [BJYP-L1 Device BJYP-L1-V1.09] on usb-0000:00:14.0-3.3/input2

Offline

#19 2024-04-01 20:20:53

seth
Member
Registered: 2012-09-03
Posts: 52,199

Re: Set uncommon screen resolution with an Arc 380

That's just some usb device (the special monitor is some touchscreen) - did you forget to "echo 6 | sudo tee /sys/module/drm/parameters/debug"?

Offline

#20 2024-04-02 11:19:26

canegiallo
Member
Registered: 2016-11-18
Posts: 14

Re: Set uncommon screen resolution with an Arc 380

did you forget to "echo 6 | sudo tee /sys/module/drm/parameters/debug"?

Yes probably. ^__^´´

Under linux-drm-tip:

Iris Pro II: https://pastebin.com/HHPRYcDd

Arc380: https://pastebin.com/Z0BtiehL

Last edited by canegiallo (2024-04-02 11:30:51)

Offline

#21 2024-04-02 13:04:13

seth
Member
Registered: 2012-09-03
Posts: 52,199

Re: Set uncommon screen resolution with an Arc 380

(Still) bad ARC

[  366.034865] i915 0000:03:00.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID:  (err -6)
[  366.034920] i915 0000:03:00.0: [drm] User-defined mode not supported: "1920x860": 60 110680 1920 1968 2000 2106 860 863 868 876 0x68 0x5
[  366.034923] [drm:drm_mode_debug_printmodeline] Modeline "1920x860": 60 110680 1920 1968 2000 2106 860 863 868 876 0x68 0x5
[  366.034937] [drm:drm_mode_prune_invalid] Not using 1920x860 mode: CLOCK_RANGE

Good IIPII

[   82.498062] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID:  (err -6)
[   82.498124] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:87:HDMI-A-2] probed modes :
[   82.498128] [drm:drm_mode_debug_printmodeline] Modeline "1920x860": 60 110680 1920 1968 2000 2106 860 863 868 876 0x48 0x5

The modelines are the same, the "DP dual mode HDMI ID:  (err -6)" is a red herring, TMDS clock is 225000 kHz everywhere
=> https://gitlab.freedesktop.org/drm/intel/-/issues

Offline

#22 2024-04-02 14:58:43

canegiallo
Member
Registered: 2016-11-18
Posts: 14

Re: Set uncommon screen resolution with an Arc 380

Bug reported https://gitlab.freedesktop.org/drm/intel/-/issues/10654.

Thank you so much for your time, attention and patience. Will give updates on this same post if I have got solutions or news from the bug report.
Until now, I will keep using the iGPU. hmm

Greetings! o/

Offline

Board footer

Powered by FluxBB