You are not logged in.
- Topics: Active | Unanswered
#1 2024-10-13 19:40:20
- flauschig
- Member
- Registered: 2024-10-13
- Posts: 8
Recent problem with smartctl + mvsas: CHECK POWER MODE not implemented
After upgrading the kernel, I can no longer get smartctl -n to work. I use something like this to collect SMART data:
smartctl -n standby --all /dev/sdXThis is to avoid waking disks when they are spun down.
I previously had linux-lts 6.6.49-1, I recently upgraded to 6.6.52-1 (now 6.6.56-1). Since 6.6.52-1, this is broken, like this:
# smartctl -n standby --all /dev/sde
smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.6.52-1-lts] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
CHECK POWER MODE: incomplete response, ATA output registers missing
CHECK POWER MODE not implemented, ignoring -n option
=== START OF INFORMATION SECTION ===
…So smartctl can no longer get the power state and always queries the drive. When I see this error, the kernel also reports this:
[ 23.721004] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 23.721012] sas: ata7: end_device-6:0: cmd error handler
[ 23.721027] sas: ata7: end_device-6:0: dev error handler
[ 23.721046] sas: ata8: end_device-6:1: dev error handler
[ 23.721051] sas: ata9: end_device-6:2: dev error handler
[ 23.721054] sas: ata10: end_device-6:3: dev error handler
[ 23.721058] sas: ata11: end_device-6:4: dev error handler
[ 23.721061] sas: ata12: end_device-6:5: dev error handler
[ 23.721067] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 1 tries: 1This effectively means all disks are spun up all the time, doubling the system’s average power draw. I don’t want that.
smartctl communicates with the drive like this:
# smartctl -d test /dev/sde
smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.6.56-1-lts] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
/dev/sde: Device of type 'scsi' [SCSI] detected
/dev/sde [SAT]: Device open changed type from 'scsi' to 'sat'
/dev/sde [SAT]: Device of type 'sat' [ATA] openedI’m not sure how I would go about diagnosing this further. I’m not a kernel hacker/developer. I would appreciate any advice!
---
System info follows:
# fastfetch -l none
root@server
-----------
OS: Arch Linux x86_64
Kernel: Linux 6.6.56-1-lts
Uptime: 3 mins
Packages: 831 (pacman)
Shell: bash 5.2.37
Display (IPS225): 1920x1080 @ 60 Hz in 23" [External]
Cursor: Adwaita
Terminal: /dev/pts/1
CPU: Intel(R) Pentium(R) G630 (2) @ 2.70 GHz
GPU: Intel 2nd Generation Core Processor Family Integrated Graphics Controller @ 1.10 GHz [Integrated]
Memory: 3.78 GiB / 7.47 GiB (51%)
Swap: 0 B / 4.00 GiB (0%)SAS controller: Areca ARC-1320-8i
Drives: various SATA drives
# lspci -vs 01:00
01:00.0 SCSI storage controller: Areca Technology Corp. ARC-1320 8/16 Port PCIe 2.0 to SAS/SATA 6Gb Non-RAID Host Adapter (rev 02)
Subsystem: Areca Technology Corp. ARC-1320 8/16 Port PCIe 2.0 to SAS/SATA 6Gb Non-RAID Host Adapter
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at f7e40000 (64-bit, non-prefetchable) [size=128K]
Memory at f7e00000 (64-bit, non-prefetchable) [size=256K]
Expansion ROM at f7e60000 [disabled] [size=64K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [70] Express Endpoint, IntMsgNum 0
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Kernel driver in use: mvsas
Kernel modules: mvsasKernel log:
[ 0.000000] microcode: updated early: 0x25 -> 0x2f, date = 2019-02-17
[ 0.000000] Linux version 6.6.56-1-lts (linux-lts@archlinux) (gcc (GCC) 14.2.1 20240910, GNU ld (GNU Binutils) 2.43.0) #1 SMP PREEMPT_DYNAMIC Thu, 10 Oct 2024 12:04:53 +0000
[ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-linux-lts root=ZFS=arch/ROOT/default rw transparent_hugepage=never audit=0 rd.log
[ 0.000000] reserving inaccessible SNB gfx pages
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x00000000000957ff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000000095800-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000020000000-0x00000000201fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000020200000-0x000000003fffffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000040000000-0x00000000401fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000040200000-0x00000000ce14efff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000ce14f000-0x00000000ce940fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ce941000-0x00000000ceb95fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000ceb96000-0x00000000ceba1fff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000ceba2000-0x00000000cebc0fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000cebc1000-0x00000000cebc5fff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000cebc6000-0x00000000cec08fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000cec09000-0x00000000ceffffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000cf800000-0x00000000df9fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed03fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000021f5fffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] APIC: Static calls initialized
[ 0.000000] SMBIOS 2.6 present.
[ 0.000000] DMI: System manufacturer System Product Name/P8H61-M LE, BIOS 4104 05/11/2012
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 2693.238 MHz processor
[ 0.001477] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.001481] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.001491] last_pfn = 0x21f600 max_arch_pfn = 0x400000000
[ 0.001500] total RAM covered: 7918M
[ 0.001733] Found optimal setting for mtrr clean up
[ 0.001734] gran_size: 64K chunk_size: 16M num_reg: 8 lose cover RAM: 0G
[ 0.001739] MTRR map: 9 entries (5 fixed + 4 variable; max 25), built from 10 variable MTRRs
[ 0.001741] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT
[ 0.002470] e820: update [mem 0xcf800000-0xffffffff] usable ==> reserved
[ 0.002480] last_pfn = 0xcf000 max_arch_pfn = 0x400000000
[ 0.012527] found SMP MP-table at [mem 0x000fccd0-0x000fccdf]
[ 0.012963] RAMDISK: [mem 0x34ce7000-0x3666afff]
[ 0.013018] ACPI: Early table checksum verification disabled
[ 0.013021] ACPI: RSDP 0x00000000000F0450 000024 (v02 ALASKA)
[ 0.013026] ACPI: XSDT 0x00000000CEB96078 000064 (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.013033] ACPI: FACP 0x00000000CEBA0370 0000F4 (v04 ALASKA A M I 01072009 AMI 00010013)
[ 0.013039] ACPI: DSDT 0x00000000CEB96170 00A1FF (v02 ALASKA A M I 00000015 INTL 20051117)
[ 0.013043] ACPI: FACS 0x00000000CEBBFF80 000040
[ 0.013046] ACPI: APIC 0x00000000CEBA0468 000062 (v03 ALASKA A M I 01072009 AMI 00010013)
[ 0.013050] ACPI: MCFG 0x00000000CEBA04D0 00003C (v01 ALASKA A M I 01072009 MSFT 00000097)
[ 0.013053] ACPI: HPET 0x00000000CEBA0510 000038 (v01 ALASKA A M I 01072009 AMI. 00000005)
[ 0.013057] ACPI: SSDT 0x00000000CEBA0548 00036D (v01 SataRe SataTabl 00001000 INTL 20091112)
[ 0.013061] ACPI: SSDT 0x00000000CEBA08B8 0008A2 (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
[ 0.013064] ACPI: SSDT 0x00000000CEBA1160 000A92 (v01 PmRef CpuPm 00003000 INTL 20051117)
[ 0.013068] ACPI: BGRT 0x00000000CEBA1C50 000038 (v00 ALASKA A M I 01072009 AMI 00010013)
[ 0.013071] ACPI: Reserving FACP table memory at [mem 0xceba0370-0xceba0463]
[ 0.013072] ACPI: Reserving DSDT table memory at [mem 0xceb96170-0xceba036e]
[ 0.013074] ACPI: Reserving FACS table memory at [mem 0xcebbff80-0xcebbffbf]
[ 0.013074] ACPI: Reserving APIC table memory at [mem 0xceba0468-0xceba04c9]
[ 0.013075] ACPI: Reserving MCFG table memory at [mem 0xceba04d0-0xceba050b]
[ 0.013076] ACPI: Reserving HPET table memory at [mem 0xceba0510-0xceba0547]
[ 0.013077] ACPI: Reserving SSDT table memory at [mem 0xceba0548-0xceba08b4]
[ 0.013078] ACPI: Reserving SSDT table memory at [mem 0xceba08b8-0xceba1159]
[ 0.013079] ACPI: Reserving SSDT table memory at [mem 0xceba1160-0xceba1bf1]
[ 0.013080] ACPI: Reserving BGRT table memory at [mem 0xceba1c50-0xceba1c87]
[ 0.013135] No NUMA configuration found
[ 0.013136] Faking a node at [mem 0x0000000000000000-0x000000021f5fffff]
[ 0.013139] NODE_DATA(0) allocated [mem 0x21f5f8000-0x21f5fcfff]
[ 0.013165] Zone ranges:
[ 0.013166] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.013168] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.013170] Normal [mem 0x0000000100000000-0x000000021f5fffff]
[ 0.013172] Device empty
[ 0.013173] Movable zone start for each node
[ 0.013174] Early memory node ranges
[ 0.013174] node 0: [mem 0x0000000000001000-0x0000000000094fff]
[ 0.013176] node 0: [mem 0x0000000000100000-0x000000001fffffff]
[ 0.013177] node 0: [mem 0x0000000020200000-0x000000003fffffff]
[ 0.013178] node 0: [mem 0x0000000040200000-0x00000000ce14efff]
[ 0.013179] node 0: [mem 0x00000000cec09000-0x00000000ceffffff]
[ 0.013180] node 0: [mem 0x0000000100000000-0x000000021f5fffff]
[ 0.013182] Initmem setup node 0 [mem 0x0000000000001000-0x000000021f5fffff]
[ 0.013187] On node 0, zone DMA: 1 pages in unavailable ranges
[ 0.013211] On node 0, zone DMA: 107 pages in unavailable ranges
[ 0.015392] On node 0, zone DMA32: 512 pages in unavailable ranges
[ 0.020570] On node 0, zone DMA32: 512 pages in unavailable ranges
[ 0.020616] On node 0, zone DMA32: 2746 pages in unavailable ranges
[ 0.031193] On node 0, zone Normal: 4096 pages in unavailable ranges
[ 0.031229] On node 0, zone Normal: 2560 pages in unavailable ranges
[ 0.031247] Reserving Intel graphics memory at [mem 0xcfa00000-0xdf9fffff]
[ 0.031414] ACPI: PM-Timer IO Port: 0x408
[ 0.031423] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[ 0.031435] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.031438] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.031440] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.031445] ACPI: Using ACPI (MADT) for SMP configuration information
[ 0.031446] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[ 0.031453] TSC deadline timer available
[ 0.031454] smpboot: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.031475] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.031478] PM: hibernation: Registered nosave memory: [mem 0x00095000-0x00095fff]
[ 0.031479] PM: hibernation: Registered nosave memory: [mem 0x00096000-0x0009ffff]
[ 0.031480] PM: hibernation: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[ 0.031481] PM: hibernation: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[ 0.031482] PM: hibernation: Registered nosave memory: [mem 0x20000000-0x201fffff]
[ 0.031484] PM: hibernation: Registered nosave memory: [mem 0x40000000-0x401fffff]
[ 0.031486] PM: hibernation: Registered nosave memory: [mem 0xce14f000-0xce940fff]
[ 0.031487] PM: hibernation: Registered nosave memory: [mem 0xce941000-0xceb95fff]
[ 0.031488] PM: hibernation: Registered nosave memory: [mem 0xceb96000-0xceba1fff]
[ 0.031489] PM: hibernation: Registered nosave memory: [mem 0xceba2000-0xcebc0fff]
[ 0.031489] PM: hibernation: Registered nosave memory: [mem 0xcebc1000-0xcebc5fff]
[ 0.031490] PM: hibernation: Registered nosave memory: [mem 0xcebc6000-0xcec08fff]
[ 0.031492] PM: hibernation: Registered nosave memory: [mem 0xcf000000-0xcf7fffff]
[ 0.031493] PM: hibernation: Registered nosave memory: [mem 0xcf800000-0xdf9fffff]
[ 0.031494] PM: hibernation: Registered nosave memory: [mem 0xdfa00000-0xf7ffffff]
[ 0.031495] PM: hibernation: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
[ 0.031496] PM: hibernation: Registered nosave memory: [mem 0xfc000000-0xfebfffff]
[ 0.031496] PM: hibernation: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[ 0.031497] PM: hibernation: Registered nosave memory: [mem 0xfec01000-0xfecfffff]
[ 0.031498] PM: hibernation: Registered nosave memory: [mem 0xfed00000-0xfed03fff]
[ 0.031499] PM: hibernation: Registered nosave memory: [mem 0xfed04000-0xfed1bfff]
[ 0.031500] PM: hibernation: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
[ 0.031501] PM: hibernation: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
[ 0.031502] PM: hibernation: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[ 0.031502] PM: hibernation: Registered nosave memory: [mem 0xfee01000-0xfeffffff]
[ 0.031503] PM: hibernation: Registered nosave memory: [mem 0xff000000-0xffffffff]
[ 0.031505] [mem 0xdfa00000-0xf7ffffff] available for PCI devices
[ 0.031507] Booting paravirtualized kernel on bare hardware
[ 0.031509] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370452778343963 ns
[ 0.038228] setup_percpu: NR_CPUS:320 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1
[ 0.038510] percpu: Embedded 64 pages/cpu s225280 r8192 d28672 u1048576
[ 0.038520] pcpu-alloc: s225280 r8192 d28672 u1048576 alloc=1*2097152
[ 0.038523] pcpu-alloc: [0] 0 1
[ 0.038540] Kernel command line: BOOT_IMAGE=/vmlinuz-linux-lts root=ZFS=arch/ROOT/default rw transparent_hugepage=never audit=0 rd.log
[ 0.038607] audit: disabled (until reboot)
[ 0.038625] Unknown kernel command line parameters "BOOT_IMAGE=/vmlinuz-linux-lts", will be passed to user space.
[ 0.039781] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[ 0.040381] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 0.040438] Fallback order for Node 0: 0
[ 0.040442] Built 1 zonelists, mobility grouping on. Total pages: 1989352
[ 0.040444] Policy zone: Normal
[ 0.040798] mem auto-init: stack:all(zero), heap alloc:on, heap free:off
[ 0.040804] software IO TLB: area num 2.
[ 0.084956] Memory: 7803708K/8084328K available (16384K kernel code, 2138K rwdata, 13036K rodata, 3436K init, 3708K bss, 280360K reserved, 0K cma-reserved)
[ 0.093765] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.093887] Kernel/User page tables isolation: enabled
[ 0.093971] ftrace: allocating 48946 entries in 192 pages
[ 0.102745] ftrace: allocated 192 pages with 2 groups
[ 0.103564] Dynamic Preempt: voluntary
[ 0.103688] rcu: Preemptible hierarchical RCU implementation.
[ 0.103689] rcu: RCU restricting CPUs from NR_CPUS=320 to nr_cpu_ids=2.
[ 0.103690] rcu: RCU priority boosting: priority 1 delay 500 ms.
[ 0.103691] Trampoline variant of Tasks RCU enabled.
[ 0.103692] Rude variant of Tasks RCU enabled.
[ 0.103692] Tracing variant of Tasks RCU enabled.
[ 0.103693] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[ 0.103694] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.107313] NR_IRQS: 20736, nr_irqs: 440, preallocated irqs: 16
[ 0.107526] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.107659] kfence: initialized - using 2097152 bytes for 255 objects at 0x(____ptrval____)-0x(____ptrval____)
[ 0.107718] Console: colour dummy device 80x25
[ 0.107721] printk: console [tty0] enabled
[ 0.108162] ACPI: Core revision 20230628
[ 0.108409] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns
[ 0.108424] APIC: Switch to symmetric I/O mode setup
[ 0.108828] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.125090] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x26d24a86e76, max_idle_ns: 440795252265 ns
[ 0.125096] Calibrating delay loop (skipped), value calculated using timer frequency.. 5388.91 BogoMIPS (lpj=8977460)
[ 0.125122] CPU0: Thermal monitoring enabled (TM1)
[ 0.125140] process: using mwait in idle threads
[ 0.125143] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 8
[ 0.125145] Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32, 1GB 0
[ 0.125148] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
[ 0.125150] Spectre V2 : Mitigation: Retpolines
[ 0.125151] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[ 0.125152] Spectre V2 : Spectre v2 / SpectreRSB : Filling RSB on VMEXIT
[ 0.125153] Spectre V2 : Enabling Restricted Speculation for firmware calls
[ 0.125154] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier
[ 0.125156] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl
[ 0.125158] MDS: Mitigation: Clear CPU buffers
[ 0.125159] MMIO Stale Data: Unknown: No mitigations
[ 0.125163] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[ 0.125164] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[ 0.125166] x86/fpu: Enabled xstate features 0x3, context size is 576 bytes, using 'standard' format.
[ 0.146308] Freeing SMP alternatives memory: 40K
[ 0.146314] pid_max: default: 32768 minimum: 301
[ 0.147071] LSM: initializing lsm=capability,landlock,lockdown,yama,bpf,integrity
[ 0.148009] landlock: Up and running.
[ 0.148010] Yama: becoming mindful.
[ 0.148016] LSM support for eBPF active
[ 0.148247] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.148260] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.149181] smpboot: CPU0: Intel(R) Pentium(R) CPU G630 @ 2.70GHz (family: 0x6, model: 0x2a, stepping: 0x7)
[ 0.149389] RCU Tasks: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1.
[ 0.149423] RCU Tasks Rude: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1.
[ 0.149452] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1.
[ 0.149475] Performance Events: PEBS fmt1+, SandyBridge events, 16-deep LBR, full-width counters, Intel PMU driver.
[ 0.149499] ... version: 3
[ 0.149500] ... bit width: 48
[ 0.149501] ... generic registers: 8
[ 0.149502] ... value mask: 0000ffffffffffff
[ 0.149503] ... max period: 00007fffffffffff
[ 0.149504] ... fixed-purpose events: 3
[ 0.149505] ... event mask: 00000007000000ff
[ 0.149659] signal: max sigframe size: 1520
[ 0.149679] Estimated ratio of average max frequency by base frequency (times 1024): 1024
[ 0.149711] rcu: Hierarchical SRCU implementation.
[ 0.149712] rcu: Max phase no-delay instances is 1000.
[ 0.150211] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[ 0.150266] smp: Bringing up secondary CPUs ...
[ 0.150407] smpboot: x86: Booting SMP configuration:
[ 0.150409] .... node #0, CPUs: #1
[ 0.157096] smp: Brought up 1 node, 2 CPUs
[ 0.157096] smpboot: Max logical packages: 1
[ 0.157096] smpboot: Total of 2 processors activated (10777.82 BogoMIPS)
[ 0.158805] devtmpfs: initialized
[ 0.158805] x86/mm: Memory block size: 128MB
[ 0.159376] ACPI: PM: Registering ACPI NVS region [mem 0xce941000-0xceb95fff] (2445312 bytes)
[ 0.159376] ACPI: PM: Registering ACPI NVS region [mem 0xceba2000-0xcebc0fff] (126976 bytes)
[ 0.159376] ACPI: PM: Registering ACPI NVS region [mem 0xcebc6000-0xcec08fff] (274432 bytes)
[ 0.159376] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[ 0.159376] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.159376] pinctrl core: initialized pinctrl subsystem
[ 0.159376] PM: RTC time: 19:05:41, date: 2024-10-13
[ 0.159672] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.159922] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations
[ 0.160027] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.160131] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.160296] thermal_sys: Registered thermal governor 'fair_share'
[ 0.160298] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.160299] thermal_sys: Registered thermal governor 'step_wise'
[ 0.160300] thermal_sys: Registered thermal governor 'user_space'
[ 0.160301] thermal_sys: Registered thermal governor 'power_allocator'
[ 0.160327] cpuidle: using governor ladder
[ 0.160332] cpuidle: using governor menu
[ 0.161814] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.161816] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.162105] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[ 0.162111] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved as E820 entry
[ 0.162122] PCI: Using configuration type 1 for base access
[ 0.162199] core: PMU erratum BJ122, BV98, HSD29 workaround disabled, HT off
[ 0.162261] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.162270] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible.
[ 0.169877] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.169880] HugeTLB: 28 KiB vmemmap can be freed for a 2.00 MiB page
[ 0.171895] ACPI: Added _OSI(Module Device)
[ 0.171895] ACPI: Added _OSI(Processor Device)
[ 0.171895] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.171895] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.177415] ACPI: 4 ACPI AML tables successfully acquired and loaded
[ 0.192935] ACPI: Dynamic OEM Table Load:
[ 0.192935] ACPI: SSDT 0xFFFF8CE940871000 00083B (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
[ 0.192935] ACPI: Dynamic OEM Table Load:
[ 0.192935] ACPI: SSDT 0xFFFF8CE940830C00 000303 (v01 PmRef ApIst 00003000 INTL 20051117)
[ 0.192935] ACPI: Dynamic OEM Table Load:
[ 0.192935] ACPI: SSDT 0xFFFF8CE940B92600 000119 (v01 PmRef ApCst 00003000 INTL 20051117)
[ 0.193366] ACPI: _OSC evaluated successfully for all CPUs
[ 0.193586] ACPI: Interpreter enabled
[ 0.193610] ACPI: PM: (supports S0 S1 S3 S4 S5)
[ 0.193611] ACPI: Using IOAPIC for interrupt routing
[ 0.194133] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.194135] PCI: Using E820 reservations for host bridge windows
[ 0.194412] ACPI: Enabled 10 GPEs in block 00 to 3F
[ 0.201978] ACPI: \_TZ_.FN00: New power resource
[ 0.202060] ACPI: \_TZ_.FN01: New power resource
[ 0.202144] ACPI: \_TZ_.FN02: New power resource
[ 0.202222] ACPI: \_TZ_.FN03: New power resource
[ 0.202302] ACPI: \_TZ_.FN04: New power resource
[ 0.202996] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[ 0.203004] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI EDR HPX-Type3]
[ 0.203092] acpi PNP0A08:00: _OSC: platform does not support [PCIeHotplug SHPCHotplug PME]
[ 0.203242] acpi PNP0A08:00: _OSC: OS now controls [AER PCIeCapability LTR DPC]
[ 0.203244] acpi PNP0A08:00: FADT indicates ASPM is unsupported, using BIOS configuration
[ 0.203843] PCI host bridge to bus 0000:00
[ 0.203845] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window]
[ 0.203848] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.203850] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[ 0.203852] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000e7fff window]
[ 0.203854] pci_bus 0000:00: root bus resource [mem 0xdfa00000-0xfeafffff window]
[ 0.203855] pci_bus 0000:00: root bus resource [bus 00-3e]
[ 0.203870] pci 0000:00:00.0: [8086:0100] type 00 class 0x060000
[ 0.203944] pci 0000:00:01.0: [8086:0101] type 01 class 0x060400
[ 0.203981] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.204067] pci 0000:00:02.0: [8086:0102] type 00 class 0x030000
[ 0.204075] pci 0000:00:02.0: reg 0x10: [mem 0xf7800000-0xf7bfffff 64bit]
[ 0.204081] pci 0000:00:02.0: reg 0x18: [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.204085] pci 0000:00:02.0: reg 0x20: [io 0xf000-0xf03f]
[ 0.204098] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[ 0.204206] pci 0000:00:16.0: [8086:1c3a] type 00 class 0x078000
[ 0.204227] pci 0000:00:16.0: reg 0x10: [mem 0xf7f06000-0xf7f0600f 64bit]
[ 0.204299] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.204367] pci 0000:00:1a.0: [8086:1c2d] type 00 class 0x0c0320
[ 0.204383] pci 0000:00:1a.0: reg 0x10: [mem 0xf7f04000-0xf7f043ff]
[ 0.204468] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 0.204569] pci 0000:00:1c.0: [8086:1c10] type 01 class 0x060400
[ 0.204662] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.204765] pci 0000:00:1c.1: [8086:1c12] type 01 class 0x060400
[ 0.204858] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.204959] pci 0000:00:1c.2: [8086:1c14] type 01 class 0x060400
[ 0.205051] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.205170] pci 0000:00:1c.4: [8086:244e] type 01 class 0x060401
[ 0.205263] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.205373] pci 0000:00:1d.0: [8086:1c26] type 00 class 0x0c0320
[ 0.205389] pci 0000:00:1d.0: reg 0x10: [mem 0xf7f03000-0xf7f033ff]
[ 0.205474] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.205567] pci 0000:00:1f.0: [8086:1c5c] type 00 class 0x060100
[ 0.205765] pci 0000:00:1f.2: [8086:1c02] type 00 class 0x010601
[ 0.205778] pci 0000:00:1f.2: reg 0x10: [io 0xf0b0-0xf0b7]
[ 0.205786] pci 0000:00:1f.2: reg 0x14: [io 0xf0a0-0xf0a3]
[ 0.205793] pci 0000:00:1f.2: reg 0x18: [io 0xf090-0xf097]
[ 0.205800] pci 0000:00:1f.2: reg 0x1c: [io 0xf080-0xf083]
[ 0.205807] pci 0000:00:1f.2: reg 0x20: [io 0xf060-0xf07f]
[ 0.205815] pci 0000:00:1f.2: reg 0x24: [mem 0xf7f02000-0xf7f027ff]
[ 0.205855] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.205933] pci 0000:00:1f.3: [8086:1c22] type 00 class 0x0c0500
[ 0.205950] pci 0000:00:1f.3: reg 0x10: [mem 0xf7f01000-0xf7f010ff 64bit]
[ 0.205970] pci 0000:00:1f.3: reg 0x20: [io 0xf040-0xf05f]
[ 0.206097] pci 0000:01:00.0: [17d3:1320] type 00 class 0x010000
[ 0.206110] pci 0000:01:00.0: reg 0x10: [mem 0xf7e40000-0xf7e5ffff 64bit]
[ 0.206119] pci 0000:01:00.0: reg 0x18: [mem 0xf7e00000-0xf7e3ffff 64bit]
[ 0.206133] pci 0000:01:00.0: reg 0x30: [mem 0xf7e60000-0xf7e6ffff pref]
[ 0.206139] pci 0000:01:00.0: enabling Extended Tags
[ 0.206172] pci 0000:01:00.0: supports D1
[ 0.206174] pci 0000:01:00.0: PME# supported from D0 D1 D3hot
[ 0.206245] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.206249] pci 0000:00:01.0: bridge window [mem 0xf7e00000-0xf7efffff]
[ 0.206339] pci 0000:02:00.0: [1912:0014] type 00 class 0x0c0330
[ 0.206381] pci 0000:02:00.0: reg 0x10: [mem 0xf7d00000-0xf7d01fff 64bit]
[ 0.206602] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 0.206815] pci 0000:00:1c.0: PCI bridge to [bus 02]
[ 0.206821] pci 0000:00:1c.0: bridge window [mem 0xf7d00000-0xf7dfffff]
[ 0.206915] pci 0000:03:00.0: [8086:10d3] type 00 class 0x020000
[ 0.206949] pci 0000:03:00.0: reg 0x10: [mem 0xf7cc0000-0xf7cdffff]
[ 0.206969] pci 0000:03:00.0: reg 0x14: [mem 0xf7c00000-0xf7c7ffff]
[ 0.206988] pci 0000:03:00.0: reg 0x18: [io 0xe000-0xe01f]
[ 0.207007] pci 0000:03:00.0: reg 0x1c: [mem 0xf7ce0000-0xf7ce3fff]
[ 0.207062] pci 0000:03:00.0: reg 0x30: [mem 0xf7c80000-0xf7cbffff pref]
[ 0.207201] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
[ 0.207419] pci 0000:00:1c.1: PCI bridge to [bus 03]
[ 0.207423] pci 0000:00:1c.1: bridge window [io 0xe000-0xefff]
[ 0.207426] pci 0000:00:1c.1: bridge window [mem 0xf7c00000-0xf7cfffff]
[ 0.207503] pci 0000:04:00.0: [10ec:8168] type 00 class 0x020000
[ 0.207528] pci 0000:04:00.0: reg 0x10: [io 0xd000-0xd0ff]
[ 0.207562] pci 0000:04:00.0: reg 0x18: [mem 0xf0004000-0xf0004fff 64bit pref]
[ 0.207583] pci 0000:04:00.0: reg 0x20: [mem 0xf0000000-0xf0003fff 64bit pref]
[ 0.207713] pci 0000:04:00.0: supports D1 D2
[ 0.207714] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.207914] pci 0000:00:1c.2: PCI bridge to [bus 04]
[ 0.207918] pci 0000:00:1c.2: bridge window [io 0xd000-0xdfff]
[ 0.207926] pci 0000:00:1c.2: bridge window [mem 0xf0000000-0xf00fffff 64bit pref]
[ 0.207999] pci 0000:05:00.0: [1b21:1080] type 01 class 0x060401
[ 0.208209] pci 0000:00:1c.4: PCI bridge to [bus 05-06] (subtractive decode)
[ 0.208219] pci 0000:00:1c.4: bridge window [io 0x0000-0x0cf7 window] (subtractive decode)
[ 0.208221] pci 0000:00:1c.4: bridge window [io 0x0d00-0xffff window] (subtractive decode)
[ 0.208223] pci 0000:00:1c.4: bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode)
[ 0.208224] pci 0000:00:1c.4: bridge window [mem 0x000d4000-0x000e7fff window] (subtractive decode)
[ 0.208226] pci 0000:00:1c.4: bridge window [mem 0xdfa00000-0xfeafffff window] (subtractive decode)
[ 0.208258] pci_bus 0000:06: extended config space not accessible
[ 0.208342] pci 0000:05:00.0: PCI bridge to [bus 06] (subtractive decode)
[ 0.208364] pci 0000:05:00.0: bridge window [io 0x0000-0x0cf7 window] (subtractive decode)
[ 0.208365] pci 0000:05:00.0: bridge window [io 0x0d00-0xffff window] (subtractive decode)
[ 0.208367] pci 0000:05:00.0: bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode)
[ 0.208368] pci 0000:05:00.0: bridge window [mem 0x000d4000-0x000e7fff window] (subtractive decode)
[ 0.208373] pci 0000:05:00.0: bridge window [mem 0xdfa00000-0xfeafffff window] (subtractive decode)
[ 0.209163] ACPI: PCI: Interrupt link LNKA configured for IRQ 11
[ 0.209231] ACPI: PCI: Interrupt link LNKB configured for IRQ 4
[ 0.209296] ACPI: PCI: Interrupt link LNKC configured for IRQ 11
[ 0.209365] ACPI: PCI: Interrupt link LNKD configured for IRQ 5
[ 0.209428] ACPI: PCI: Interrupt link LNKE configured for IRQ 0
[ 0.209429] ACPI: PCI: Interrupt link LNKE disabled
[ 0.209491] ACPI: PCI: Interrupt link LNKF configured for IRQ 10
[ 0.209553] ACPI: PCI: Interrupt link LNKG configured for IRQ 0
[ 0.209554] ACPI: PCI: Interrupt link LNKG disabled
[ 0.209619] ACPI: PCI: Interrupt link LNKH configured for IRQ 3
[ 0.211798] iommu: Default domain type: Translated
[ 0.211798] iommu: DMA domain TLB invalidation policy: lazy mode
[ 0.211989] SCSI subsystem initialized
[ 0.211997] libata version 3.00 loaded.
[ 0.211997] ACPI: bus type USB registered
[ 0.211997] usbcore: registered new interface driver usbfs
[ 0.211997] usbcore: registered new interface driver hub
[ 0.211997] usbcore: registered new device driver usb
[ 0.211997] pps_core: LinuxPPS API ver. 1 registered
[ 0.211997] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.211997] PTP clock support registered
[ 0.211997] EDAC MC: Ver: 3.0.0
[ 0.212004] NetLabel: Initializing
[ 0.212006] NetLabel: domain hash size = 128
[ 0.212007] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 0.212025] NetLabel: unlabeled traffic allowed by default
[ 0.212029] mctp: management component transport protocol core
[ 0.212030] NET: Registered PF_MCTP protocol family
[ 0.212035] PCI: Using ACPI for IRQ routing
[ 0.212964] PCI: pci_cache_line_size set to 64 bytes
[ 0.212964] e820: reserve RAM buffer [mem 0x00095800-0x0009ffff]
[ 0.212964] e820: reserve RAM buffer [mem 0xce14f000-0xcfffffff]
[ 0.212964] e820: reserve RAM buffer [mem 0xcf000000-0xcfffffff]
[ 0.212964] e820: reserve RAM buffer [mem 0x21f600000-0x21fffffff]
[ 0.212964] pci 0000:00:02.0: vgaarb: setting as boot VGA device
[ 0.212964] pci 0000:00:02.0: vgaarb: bridge control possible
[ 0.212964] pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[ 0.212964] vgaarb: loaded
[ 0.216065] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.216077] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.218111] clocksource: Switched to clocksource tsc-early
[ 0.218111] VFS: Disk quotas dquot_6.6.0
[ 0.218111] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.218111] pnp: PnP ACPI init
[ 0.218111] system 00:00: [mem 0xfed40000-0xfed44fff] has been reserved
[ 0.218111] system 00:01: [io 0x0680-0x069f] has been reserved
[ 0.218111] system 00:01: [io 0x0200-0x020f] has been reserved
[ 0.218111] system 00:01: [io 0xffff] has been reserved
[ 0.218111] system 00:01: [io 0xffff] has been reserved
[ 0.218111] system 00:01: [io 0x0400-0x0453] has been reserved
[ 0.218111] system 00:01: [io 0x0458-0x047f] has been reserved
[ 0.218111] system 00:01: [io 0x0500-0x057f] has been reserved
[ 0.218111] system 00:01: [io 0x164e-0x164f] has been reserved
[ 0.218111] system 00:03: [io 0x0454-0x0457] has been reserved
[ 0.218111] system 00:04: [io 0x0290-0x029f] has been reserved
[ 0.218111] system 00:05: [io 0x04d0-0x04d1] has been reserved
[ 0.218111] system 00:06: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.218111] system 00:06: [mem 0xfed10000-0xfed17fff] has been reserved
[ 0.218111] system 00:06: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.218111] system 00:06: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.218111] system 00:06: [mem 0xf8000000-0xfbffffff] has been reserved
[ 0.218111] system 00:06: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.218111] system 00:06: [mem 0xfed90000-0xfed93fff] has been reserved
[ 0.218111] system 00:06: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 0.218111] system 00:06: [mem 0xff000000-0xffffffff] has been reserved
[ 0.218111] system 00:06: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 0.218111] system 00:06: [mem 0xdfa00000-0xdfa00fff] has been reserved
[ 0.218111] system 00:07: [mem 0x20000000-0x201fffff] has been reserved
[ 0.218111] system 00:07: [mem 0x40000000-0x401fffff] has been reserved
[ 0.218111] pnp: PnP ACPI: found 8 devices
[ 0.223681] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[ 0.223837] NET: Registered PF_INET protocol family
[ 0.223957] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.226234] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear)
[ 0.226266] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.226312] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.226573] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear)
[ 0.226866] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.227021] MPTCP token hash table entries: 8192 (order: 5, 196608 bytes, linear)
[ 0.227080] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear)
[ 0.227110] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear)
[ 0.227220] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.227227] NET: Registered PF_XDP protocol family
[ 0.227244] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.227249] pci 0000:00:01.0: bridge window [mem 0xf7e00000-0xf7efffff]
[ 0.227255] pci 0000:00:1c.0: PCI bridge to [bus 02]
[ 0.227259] pci 0000:00:1c.0: bridge window [mem 0xf7d00000-0xf7dfffff]
[ 0.227267] pci 0000:00:1c.1: PCI bridge to [bus 03]
[ 0.227270] pci 0000:00:1c.1: bridge window [io 0xe000-0xefff]
[ 0.227274] pci 0000:00:1c.1: bridge window [mem 0xf7c00000-0xf7cfffff]
[ 0.227282] pci 0000:00:1c.2: PCI bridge to [bus 04]
[ 0.227284] pci 0000:00:1c.2: bridge window [io 0xd000-0xdfff]
[ 0.227291] pci 0000:00:1c.2: bridge window [mem 0xf0000000-0xf00fffff 64bit pref]
[ 0.227297] pci 0000:05:00.0: PCI bridge to [bus 06]
[ 0.227316] pci 0000:00:1c.4: PCI bridge to [bus 05-06]
[ 0.227327] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window]
[ 0.227329] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window]
[ 0.227331] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[ 0.227332] pci_bus 0000:00: resource 7 [mem 0x000d4000-0x000e7fff window]
[ 0.227334] pci_bus 0000:00: resource 8 [mem 0xdfa00000-0xfeafffff window]
[ 0.227335] pci_bus 0000:01: resource 1 [mem 0xf7e00000-0xf7efffff]
[ 0.227337] pci_bus 0000:02: resource 1 [mem 0xf7d00000-0xf7dfffff]
[ 0.227339] pci_bus 0000:03: resource 0 [io 0xe000-0xefff]
[ 0.227340] pci_bus 0000:03: resource 1 [mem 0xf7c00000-0xf7cfffff]
[ 0.227342] pci_bus 0000:04: resource 0 [io 0xd000-0xdfff]
[ 0.227343] pci_bus 0000:04: resource 2 [mem 0xf0000000-0xf00fffff 64bit pref]
[ 0.227345] pci_bus 0000:05: resource 4 [io 0x0000-0x0cf7 window]
[ 0.227346] pci_bus 0000:05: resource 5 [io 0x0d00-0xffff window]
[ 0.227348] pci_bus 0000:05: resource 6 [mem 0x000a0000-0x000bffff window]
[ 0.227349] pci_bus 0000:05: resource 7 [mem 0x000d4000-0x000e7fff window]
[ 0.227351] pci_bus 0000:05: resource 8 [mem 0xdfa00000-0xfeafffff window]
[ 0.227352] pci_bus 0000:06: resource 4 [io 0x0000-0x0cf7 window]
[ 0.227354] pci_bus 0000:06: resource 5 [io 0x0d00-0xffff window]
[ 0.227355] pci_bus 0000:06: resource 6 [mem 0x000a0000-0x000bffff window]
[ 0.227356] pci_bus 0000:06: resource 7 [mem 0x000d4000-0x000e7fff window]
[ 0.227358] pci_bus 0000:06: resource 8 [mem 0xdfa00000-0xfeafffff window]
[ 0.227455] pci 0000:00:02.0: BIOS left Intel GPU interrupts enabled; disabling
[ 0.355221] pci 0000:00:1a.0: quirk_usb_early_handoff+0x0/0x7d0 took 124761 usecs
[ 0.481891] pci 0000:00:1d.0: quirk_usb_early_handoff+0x0/0x7d0 took 123680 usecs
[ 0.482076] pci 0000:02:00.0: CLS mismatch (64 != 32), using 64 bytes
[ 0.482082] pci 0000:05:00.0: Disabling ASPM L0s/L1
[ 0.482096] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.482098] software IO TLB: mapped [mem 0x00000000ca14f000-0x00000000ce14f000] (64MB)
[ 0.482149] Trying to unpack rootfs image as initramfs...
[ 0.485626] Initialise system trusted keyrings
[ 0.485658] Key type blacklist registered
[ 0.485734] workingset: timestamp_bits=41 max_order=21 bucket_order=0
[ 0.485746] zbud: loaded
[ 0.486152] integrity: Platform Keyring initialized
[ 0.486160] integrity: Machine keyring initialized
[ 0.496698] Key type asymmetric registered
[ 0.496703] Asymmetric key parser 'x509' registered
[ 0.496734] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242)
[ 0.496817] io scheduler mq-deadline registered
[ 0.496819] io scheduler kyber registered
[ 0.496848] io scheduler bfq registered
[ 0.497720] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 0.498056] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.498085] ACPI: button: Power Button [PWRB]
[ 0.498119] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.498730] ACPI: button: Power Button [PWRF]
[ 0.499416] thermal LNXTHERM:00: registered as thermal_zone0
[ 0.499420] ACPI: thermal: Thermal Zone [TZ00] (28 C)
[ 0.499712] thermal LNXTHERM:01: registered as thermal_zone1
[ 0.499714] ACPI: thermal: Thermal Zone [TZ01] (30 C)
[ 0.499873] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 0.502241] Non-volatile memory driver v1.3
[ 0.502245] Linux agpgart interface v0.103
[ 0.502278] AMD-Vi: AMD IOMMUv2 functionality not available on this system - This is not a bug.
[ 0.502304] ACPI: bus type drm_connector registered
[ 0.502887] ahci 0000:00:1f.2: version 3.0
[ 0.515142] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 4 ports 3 Gbps 0x33 impl SATA mode
[ 0.515152] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part ems apst
[ 0.545649] scsi host0: ahci
[ 0.545824] scsi host1: ahci
[ 0.545922] scsi host2: ahci
[ 0.546042] scsi host3: ahci
[ 0.546143] scsi host4: ahci
[ 0.546242] scsi host5: ahci
[ 0.546285] ata1: SATA max UDMA/133 abar m2048@0xf7f02000 port 0xf7f02100 irq 25
[ 0.546288] ata2: SATA max UDMA/133 abar m2048@0xf7f02000 port 0xf7f02180 irq 25
[ 0.546289] ata3: DUMMY
[ 0.546290] ata4: DUMMY
[ 0.546292] ata5: SATA max UDMA/133 abar m2048@0xf7f02000 port 0xf7f02300 irq 25
[ 0.546293] ata6: SATA max UDMA/133 abar m2048@0xf7f02000 port 0xf7f02380 irq 25
[ 0.546407] usbcore: registered new interface driver usbserial_generic
[ 0.546412] usbserial: USB Serial support registered for generic
[ 0.546512] rtc_cmos 00:02: RTC can wake from S4
[ 0.546770] rtc_cmos 00:02: registered as rtc0
[ 0.546805] rtc_cmos 00:02: setting system clock to 2024-10-13T19:05:41 UTC (1728846341)
[ 0.546840] rtc_cmos 00:02: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 0.546928] intel_pstate: Intel P-state driver initializing
[ 0.547651] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.548210] [drm] Initialized simpledrm 1.0.0 20200625 for simple-framebuffer.0 on minor 0
[ 0.549340] fbcon: Deferring console take-over
[ 0.549345] simple-framebuffer simple-framebuffer.0: [drm] fb0: simpledrmdrmfb frame buffer device
[ 0.549443] hid: raw HID events driver (C) Jiri Kosina
[ 0.549555] drop_monitor: Initializing network drop monitor service
[ 0.552278] ehci-pci 0000:00:1a.0: EHCI Host Controller
[ 0.552291] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 0.552305] ehci-pci 0000:00:1a.0: debug port 2
[ 0.558641] ehci-pci 0000:00:1a.0: irq 23, io mem 0xf7f04000
[ 0.565984] Initializing XFRM netlink socket
[ 0.566136] NET: Registered PF_INET6 protocol family
[ 0.571755] Freeing initrd memory: 26128K
[ 0.571802] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 0.571915] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.06
[ 0.571918] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.571920] usb usb1: Product: EHCI Host Controller
[ 0.571922] usb usb1: Manufacturer: Linux 6.6.56-1-lts ehci_hcd
[ 0.571923] usb usb1: SerialNumber: 0000:00:1a.0
[ 0.572095] hub 1-0:1.0: USB hub found
[ 0.572104] hub 1-0:1.0: 2 ports detected
[ 0.572317] ehci-pci 0000:00:1d.0: EHCI Host Controller
[ 0.572325] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 0.572338] ehci-pci 0000:00:1d.0: debug port 2
[ 0.577677] ehci-pci 0000:00:1d.0: irq 23, io mem 0xf7f03000
[ 0.582864] Segment Routing with IPv6
[ 0.582867] RPL Segment Routing with IPv6
[ 0.582886] In-situ OAM (IOAM) with IPv6
[ 0.582929] NET: Registered PF_PACKET protocol family
[ 0.583289] microcode: Microcode Update Driver: v2.2.
[ 0.583293] IPI shorthand broadcast: enabled
[ 0.585504] sched_clock: Marking stable (584229742, 868246)->(589165292, -4067304)
[ 0.585716] registered taskstats version 1
[ 0.585851] Loading compiled-in X.509 certificates
[ 0.588451] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 0.588528] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.06
[ 0.588531] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.588533] usb usb2: Product: EHCI Host Controller
[ 0.588534] usb usb2: Manufacturer: Linux 6.6.56-1-lts ehci_hcd
[ 0.588536] usb usb2: SerialNumber: 0000:00:1d.0
[ 0.588670] hub 2-0:1.0: USB hub found
[ 0.588678] hub 2-0:1.0: 2 ports detected
[ 0.589695] Loaded X.509 cert 'Build time autogenerated kernel key: 6407bc0729bc9a194e7dd12f18ddec23cb12a168'
[ 0.591749] zswap: loaded using pool zstd/zsmalloc
[ 0.594299] Key type .fscrypt registered
[ 0.594301] Key type fscrypt-provisioning registered
[ 0.594699] PM: Magic number: 12:530:91
[ 0.594759] memory_tiering memory_tier4: hash matches
[ 0.597879] RAS: Correctable Errors collector initialized.
[ 0.597966] clk: Disabling unused clocks
[ 0.821819] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 0.838485] usb 2-1: new high-speed USB device number 2 using ehci-pci
[ 0.861818] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 0.861841] ata1: SATA link down (SStatus 0 SControl 300)
[ 0.862467] ACPI BIOS Error (bug): Could not resolve symbol [\_SB.PCI0.SAT0.SPT1._GTF.DSSP], AE_NOT_FOUND (20230628/psargs-332)
[ 0.862480] fbcon: Taking over console
[ 0.862488] ACPI Error: Aborting method \_SB.PCI0.SAT0.SPT1._GTF due to previous error (AE_NOT_FOUND) (20230628/psparse-529)
[ 0.862599] ata2.00: ATA-9: WDC WD10JFCX-68N6GN0, 82.00A82, max UDMA/133
[ 0.862915] ata2.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 32), AA
[ 0.863607] ACPI BIOS Error (bug): Could not resolve symbol [\_SB.PCI0.SAT0.SPT1._GTF.DSSP], AE_NOT_FOUND (20230628/psargs-332)
[ 0.863620] ACPI Error: Aborting method \_SB.PCI0.SAT0.SPT1._GTF due to previous error (AE_NOT_FOUND) (20230628/psparse-529)
[ 0.863810] ata2.00: configured for UDMA/133
[ 0.863965] scsi 1:0:0:0: Direct-Access ATA WDC WD10JFCX-68N 0A82 PQ: 0 ANSI: 5
[ 0.864352] sd 1:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[ 0.864355] sd 1:0:0:0: [sda] 4096-byte physical blocks
[ 0.864364] sd 1:0:0:0: [sda] Write Protect is off
[ 0.864366] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 0.864380] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 0.864398] sd 1:0:0:0: [sda] Preferred minimum I/O size 4096 bytes
[ 0.866623] Console: switching to colour frame buffer device 240x67
[ 0.878456] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 0.878482] ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 0.879289] ACPI BIOS Error (bug): Could not resolve symbol [\_SB.PCI0.SAT0.SPT5._GTF.DSSP], AE_NOT_FOUND (20230628/psargs-332)
[ 0.879332] ACPI Error: Aborting method \_SB.PCI0.SAT0.SPT5._GTF due to previous error (AE_NOT_FOUND) (20230628/psparse-529)
[ 0.879359] ata6.00: ATA-11: WDC WDS500G2B0A, X61190WD, max UDMA/133
[ 0.879403] ACPI BIOS Error (bug): Could not resolve symbol [\_SB.PCI0.SAT0.SPT4._GTF.DSSP], AE_NOT_FOUND (20230628/psargs-332)
[ 0.879433] ACPI Error: Aborting method \_SB.PCI0.SAT0.SPT4._GTF due to previous error (AE_NOT_FOUND) (20230628/psparse-529)
[ 0.879640] ata6.00: 976773168 sectors, multi 1: LBA48 NCQ (depth 32), AA
[ 0.879658] ata5.00: ATA-8: HGST HTE541010A9E680, JA0OA7J0, max UDMA/133
[ 0.880046] ata5.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 32), AA
[ 0.881123] ACPI BIOS Error (bug): Could not resolve symbol [\_SB.PCI0.SAT0.SPT4._GTF.DSSP], AE_NOT_FOUND (20230628/psargs-332)
[ 0.881230] ACPI Error: Aborting method \_SB.PCI0.SAT0.SPT4._GTF due to previous error (AE_NOT_FOUND) (20230628/psparse-529)
[ 0.881606] ata5.00: configured for UDMA/133
[ 0.881771] scsi 4:0:0:0: Direct-Access ATA HGST HTE541010A9 A7J0 PQ: 0 ANSI: 5
[ 0.881926] ata6.00: Features: Dev-Sleep
[ 0.882116] sd 4:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[ 0.882120] sd 4:0:0:0: [sdb] 4096-byte physical blocks
[ 0.882134] sd 4:0:0:0: [sdb] Write Protect is off
[ 0.882137] sd 4:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 0.882156] sd 4:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 0.882176] sd 4:0:0:0: [sdb] Preferred minimum I/O size 4096 bytes
[ 0.882732] ACPI BIOS Error (bug): Could not resolve symbol [\_SB.PCI0.SAT0.SPT5._GTF.DSSP], AE_NOT_FOUND (20230628/psargs-332)
[ 0.882766] ACPI Error: Aborting method \_SB.PCI0.SAT0.SPT5._GTF due to previous error (AE_NOT_FOUND) (20230628/psparse-529)
[ 0.885130] ata6.00: configured for UDMA/133
[ 0.885228] scsi 5:0:0:0: Direct-Access ATA WDC WDS500G2B0A 90WD PQ: 0 ANSI: 5
[ 0.885479] sd 5:0:0:0: [sdc] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[ 0.885488] sd 5:0:0:0: [sdc] Write Protect is off
[ 0.885490] sd 5:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 0.885502] sd 5:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 0.885519] sd 5:0:0:0: [sdc] Preferred minimum I/O size 512 bytes
[ 0.887355] sdc: sdc1 sdc2 sdc3 sdc4
[ 0.887524] sd 5:0:0:0: [sdc] Attached SCSI disk
[ 0.916140] sda: sda1 sda9
[ 0.916314] sd 1:0:0:0: [sda] Attached SCSI disk
[ 0.945120] sdb: sdb1 sdb9
[ 0.945405] sd 4:0:0:0: [sdb] Attached SCSI disk
[ 0.948003] Freeing unused decrypted memory: 2028K
[ 0.948515] Freeing unused kernel image (initmem) memory: 3436K
[ 0.948583] Write protecting the kernel read-only data: 30720k
[ 0.949027] Freeing unused kernel image (rodata/data gap) memory: 1300K
[ 0.968839] usb 1-1: New USB device found, idVendor=8087, idProduct=0024, bcdDevice= 0.00
[ 0.968844] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 0.969112] hub 1-1:1.0: USB hub found
[ 0.969180] hub 1-1:1.0: 4 ports detected
[ 0.985461] usb 2-1: New USB device found, idVendor=8087, idProduct=0024, bcdDevice= 0.00
[ 0.985466] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 0.985782] hub 2-1:1.0: USB hub found
[ 0.985931] hub 2-1:1.0: 6 ports detected
[ 0.999478] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[ 0.999483] rodata_test: all tests were successful
[ 0.999485] x86/mm: Checking user space page tables
[ 1.047649] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[ 1.047658] Run /init as init process
[ 1.047660] with arguments:
[ 1.047661] /init
[ 1.047662] with environment:
[ 1.047663] HOME=/
[ 1.047664] TERM=linux
[ 1.047664] BOOT_IMAGE=/vmlinuz-linux-lts
[ 1.063969] initramfs: :: running early hook [udev]
[ 1.075145] initramfs: Starting systemd-udevd version 256.7-1-arch
[ 1.078685] initramfs: :: running hook [udev]
[ 1.080048] initramfs: :: Triggering uevents...
[ 1.273212] usb 2-1.1: new high-speed USB device number 3 using ehci-pci
[ 1.297841] xhci_hcd 0000:02:00.0: failed to load firmware renesas_usb_fw.mem, fallback to ROM
[ 1.297959] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 1.297967] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 3
[ 1.311682] xhci_hcd 0000:02:00.0: hcc params 0x014051c7 hci version 0x100 quirks 0x0000001100000410
[ 1.312156] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 1.312161] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 4
[ 1.312166] xhci_hcd 0000:02:00.0: Host supports USB 3.0 SuperSpeed
[ 1.312238] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.06
[ 1.312241] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.312243] usb usb3: Product: xHCI Host Controller
[ 1.312245] usb usb3: Manufacturer: Linux 6.6.56-1-lts xhci-hcd
[ 1.312246] usb usb3: SerialNumber: 0000:02:00.0
[ 1.313829] hub 3-0:1.0: USB hub found
[ 1.313851] hub 3-0:1.0: 4 ports detected
[ 1.314094] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 1.314355] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.06
[ 1.314359] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.314360] usb usb4: Product: xHCI Host Controller
[ 1.314362] usb usb4: Manufacturer: Linux 6.6.56-1-lts xhci-hcd
[ 1.314364] usb usb4: SerialNumber: 0000:02:00.0
[ 1.314479] hub 4-0:1.0: USB hub found
[ 1.314495] hub 4-0:1.0: 4 ports detected
[ 1.316673] mvsas 0000:01:00.0: mvsas: driver version 0.8.16
[ 1.316946] mvsas 0000:01:00.0: mvsas: PCI-E x8, Bandwidth Usage: 5.0 Gbps
[ 1.370890] tsc: Refined TSC clocksource calibration: 2693.208 MHz
[ 1.370899] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x26d22e903be, max_idle_ns: 440795336784 ns
[ 1.476988] clocksource: Switched to clocksource tsc
[ 1.492139] spl: loading out-of-tree module taints kernel.
[ 1.492152] spl: module verification failed: signature and/or required key missing - tainting kernel
[ 1.594970] zfs: module license 'CDDL' taints kernel.
[ 1.594976] Disabling lock debugging due to kernel taint
[ 1.595002] zfs: module license taints kernel.
[ 2.600497] zfs: unknown parameter 'zfs_resilver_delay' ignored
[ 2.600510] zfs: unknown parameter 'zfs_scrub_delay' ignored
[ 2.600520] zfs: unknown parameter 'zfs_top_maxinflight' ignored
[ 2.615277] Console: switching to colour dummy device 80x25
[ 2.615958] usb 2-1.1: New USB device found, idVendor=090c, idProduct=1000, bcdDevice=11.00
[ 2.615963] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.615965] usb 2-1.1: SerialNumber: AA201111078050
[ 2.625808] usb-storage 2-1.1:1.0: USB Mass Storage device detected
[ 2.626241] scsi host7: usb-storage 2-1.1:1.0
[ 2.626328] usbcore: registered new interface driver usb-storage
[ 2.630749] i915 0000:00:02.0: vgaarb: deactivate vga console
[ 2.633909] usbcore: registered new interface driver uas
[ 2.669342] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 1
[ 2.669910] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 2.670324] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input2
[ 2.977867] fbcon: i915drmfb (fb0) is primary device
[ 3.116626] Console: switching to colour frame buffer device 240x67
[ 3.135023] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device
[ 3.858713] ZFS: Loaded module v2.2.4-1, ZFS pool version 5000, ZFS filesystem version 5
[ 3.878332] scsi 7:0:0:0: Direct-Access 1100 PQ: 0 ANSI: 4
[ 3.879931] sd 7:0:0:0: [sdd] 15950592 512-byte logical blocks: (8.17 GB/7.61 GiB)
[ 3.880680] sd 7:0:0:0: [sdd] Write Protect is off
[ 3.880682] sd 7:0:0:0: [sdd] Mode Sense: 43 00 00 00
[ 3.881431] sd 7:0:0:0: [sdd] No Caching mode page found
[ 3.881433] sd 7:0:0:0: [sdd] Assuming drive cache: write through
[ 3.885937] sdd: sdd1
[ 3.886002] sd 7:0:0:0: [sdd] Attached SCSI removable disk
[ 4.204261] drivers/scsi/mvsas/mv_sas.c 1058:phy 0 attach dev info is 0
[ 4.204270] drivers/scsi/mvsas/mv_sas.c 1060:phy 0 attach sas addr is 0
[ 4.310927] drivers/scsi/mvsas/mv_94xx.c 869:get all reg link rate is 0x122000
[ 4.310942] drivers/scsi/mvsas/mv_94xx.c 874:get link rate is 10
[ 4.430960] drivers/scsi/mvsas/mv_sas.c 1058:phy 1 attach dev info is 20001
[ 4.430962] drivers/scsi/mvsas/mv_sas.c 1060:phy 1 attach sas addr is 1
[ 4.537595] drivers/scsi/mvsas/mv_94xx.c 869:get all reg link rate is 0x122000
[ 4.537602] drivers/scsi/mvsas/mv_94xx.c 874:get link rate is 10
[ 4.657620] drivers/scsi/mvsas/mv_sas.c 1058:phy 2 attach dev info is 20001
[ 4.657622] drivers/scsi/mvsas/mv_sas.c 1060:phy 2 attach sas addr is 2
[ 4.764258] drivers/scsi/mvsas/mv_94xx.c 869:get all reg link rate is 0x122000
[ 4.764265] drivers/scsi/mvsas/mv_94xx.c 874:get link rate is 10
[ 4.884282] drivers/scsi/mvsas/mv_sas.c 1058:phy 3 attach dev info is 20001
[ 4.884285] drivers/scsi/mvsas/mv_sas.c 1060:phy 3 attach sas addr is 3
[ 7.747570] drivers/scsi/mvsas/mv_94xx.c 869:get all reg link rate is 0x122000
[ 7.747578] drivers/scsi/mvsas/mv_94xx.c 874:get link rate is 10
[ 7.867595] drivers/scsi/mvsas/mv_sas.c 1058:phy 4 attach dev info is 20001
[ 7.867597] drivers/scsi/mvsas/mv_sas.c 1060:phy 4 attach sas addr is 4
[ 7.974259] drivers/scsi/mvsas/mv_94xx.c 869:get all reg link rate is 0x122000
[ 7.974267] drivers/scsi/mvsas/mv_94xx.c 874:get link rate is 10
[ 8.094284] drivers/scsi/mvsas/mv_sas.c 1058:phy 5 attach dev info is 20001
[ 8.094286] drivers/scsi/mvsas/mv_sas.c 1060:phy 5 attach sas addr is 5
[ 8.200924] drivers/scsi/mvsas/mv_94xx.c 869:get all reg link rate is 0x122000
[ 8.200931] drivers/scsi/mvsas/mv_94xx.c 874:get link rate is 10
[ 8.320948] drivers/scsi/mvsas/mv_sas.c 1058:phy 6 attach dev info is 20001
[ 8.320950] drivers/scsi/mvsas/mv_sas.c 1060:phy 6 attach sas addr is 6
[ 8.427590] drivers/scsi/mvsas/mv_sas.c 1058:phy 7 attach dev info is 0
[ 8.427598] drivers/scsi/mvsas/mv_sas.c 1060:phy 7 attach sas addr is 0
[ 8.427607] scsi host6: mvsas
[ 8.428267] drivers/scsi/mvsas/mv_sas.c 261:phy 1 byte dmaded.
[ 8.428271] drivers/scsi/mvsas/mv_sas.c 261:phy 2 byte dmaded.
[ 8.428272] drivers/scsi/mvsas/mv_sas.c 261:phy 3 byte dmaded.
[ 8.428274] drivers/scsi/mvsas/mv_sas.c 261:phy 4 byte dmaded.
[ 8.428275] drivers/scsi/mvsas/mv_sas.c 261:phy 5 byte dmaded.
[ 8.428276] drivers/scsi/mvsas/mv_sas.c 261:phy 6 byte dmaded.
[ 8.428446] sas: phy-6:1 added to port-6:0, phy_mask:0x2 (0100000000000000)
[ 8.428788] sas: DOING DISCOVERY on port 0, pid:11
[ 8.428801] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 8.428809] sas: ata7: end_device-6:0: dev error handler
[ 8.585976] ata7.00: ATA-11: ST4000NE001-2MA101, EN01, max UDMA/133
[ 8.598959] ata7.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth 32)
[ 8.605554] ata7.00: Features: NCQ-sndrcv
[ 8.626348] ata7.00: configured for UDMA/133
[ 8.626371] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 8.626691] scsi 6:0:0:0: Direct-Access ATA ST4000NE001-2MA1 EN01 PQ: 0 ANSI: 5
[ 8.626970] sas: DONE DISCOVERY on port 0, pid:11, result:0
[ 8.627082] sas: phy-6:2 added to port-6:1, phy_mask:0x4 (0200000000000000)
[ 8.627255] sas: DOING DISCOVERY on port 1, pid:11
[ 8.627307] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 8.627341] sas: ata7: end_device-6:0: dev error handler
[ 8.627366] sas: ata8: end_device-6:1: dev error handler
[ 8.791596] ata8.00: ATA-9: HGST HDN726040ALE614, APGNW7JH, max UDMA/133
[ 8.801900] ata8.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 32)
[ 8.801909] ata8.00: Features: NCQ-prio
[ 8.806735] ata8.00: configured for UDMA/133
[ 8.806763] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 8.807081] scsi 6:0:1:0: Direct-Access ATA HGST HDN726040AL W7JH PQ: 0 ANSI: 5
[ 8.807283] sas: DONE DISCOVERY on port 1, pid:11, result:0
[ 8.807393] sas: phy-6:3 added to port-6:2, phy_mask:0x8 (0300000000000000)
[ 8.807678] sas: DOING DISCOVERY on port 2, pid:11
[ 8.807697] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 8.807710] sas: ata7: end_device-6:0: dev error handler
[ 8.807725] sas: ata8: end_device-6:1: dev error handler
[ 8.807730] sas: ata9: end_device-6:2: dev error handler
[ 8.970730] ata9.00: ATA-9: HGST HDN726040ALE614, APGNW7JH, max UDMA/133
[ 8.980176] ata9.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 32)
[ 8.980185] ata9.00: Features: NCQ-prio
[ 8.985218] ata9.00: configured for UDMA/133
[ 8.985244] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 8.985537] scsi 6:0:2:0: Direct-Access ATA HGST HDN726040AL W7JH PQ: 0 ANSI: 5
[ 8.985816] sas: DONE DISCOVERY on port 2, pid:11, result:0
[ 8.985927] sas: phy-6:4 added to port-6:3, phy_mask:0x1 (0400000000000000)
[ 8.986170] sas: DOING DISCOVERY on port 3, pid:11
[ 8.986187] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 8.986199] sas: ata7: end_device-6:0: dev error handler
[ 8.986213] sas: ata8: end_device-6:1: dev error handler
[ 8.986218] sas: ata9: end_device-6:2: dev error handler
[ 8.986221] sas: ata10: end_device-6:3: dev error handler
[ 9.141543] ata10.00: ATA-9: WDC WD4003FFBX-68MU3N0, 83.00A83, max UDMA/133
[ 9.147114] ata10.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 32)
[ 9.147123] ata10.00: Features: NCQ-sndrcv NCQ-prio
[ 9.156472] ata10.00: configured for UDMA/133
[ 9.156497] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 9.156791] scsi 6:0:3:0: Direct-Access ATA WDC WD4003FFBX-6 0A83 PQ: 0 ANSI: 5
[ 9.157071] sas: DONE DISCOVERY on port 3, pid:11, result:0
[ 9.157191] sas: phy-6:5 added to port-6:4, phy_mask:0x2 (0500000000000000)
[ 9.157442] sas: DOING DISCOVERY on port 4, pid:11
[ 9.157459] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 9.157472] sas: ata7: end_device-6:0: dev error handler
[ 9.157486] sas: ata8: end_device-6:1: dev error handler
[ 9.157491] sas: ata9: end_device-6:2: dev error handler
[ 9.157495] sas: ata10: end_device-6:3: dev error handler
[ 9.157498] sas: ata11: end_device-6:4: dev error handler
[ 9.450359] ata11.00: ATA-8: TOSHIBA HDWQ140, FJ1M, max UDMA/100
[ 9.450366] ata11.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth 32)
[ 9.452176] ata11.00: configured for UDMA/100
[ 9.452200] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 9.452496] scsi 6:0:4:0: Direct-Access ATA TOSHIBA HDWQ140 FJ1M PQ: 0 ANSI: 5
[ 9.452777] sas: DONE DISCOVERY on port 4, pid:11, result:0
[ 9.452889] sas: phy-6:6 added to port-6:5, phy_mask:0x4 (0600000000000000)
[ 9.453138] sas: DOING DISCOVERY on port 5, pid:11
[ 9.453154] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 9.453170] sas: ata7: end_device-6:0: dev error handler
[ 9.453186] sas: ata8: end_device-6:1: dev error handler
[ 9.453190] sas: ata9: end_device-6:2: dev error handler
[ 9.453194] sas: ata10: end_device-6:3: dev error handler
[ 9.453198] sas: ata11: end_device-6:4: dev error handler
[ 9.453202] sas: ata12: end_device-6:5: dev error handler
[ 9.608265] ata12.00: ATA-9: WDC WD4003FFBX-68MU3N0, 83.00A83, max UDMA/133
[ 9.613955] ata12.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 32)
[ 9.613964] ata12.00: Features: NCQ-sndrcv NCQ-prio
[ 9.623470] ata12.00: configured for UDMA/133
[ 9.623496] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 9.623798] scsi 6:0:5:0: Direct-Access ATA WDC WD4003FFBX-6 0A83 PQ: 0 ANSI: 5
[ 9.624058] sas: DONE DISCOVERY on port 5, pid:11, result:0
[ 9.624547] sd 6:0:1:0: [sdf] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB)
[ 9.624553] sd 6:0:1:0: [sdf] 4096-byte physical blocks
[ 9.624568] sd 6:0:1:0: [sdf] Write Protect is off
[ 9.624571] sd 6:0:1:0: [sdf] Mode Sense: 00 3a 00 00
[ 9.624594] sd 6:0:1:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.624626] sd 6:0:1:0: [sdf] Preferred minimum I/O size 4096 bytes
[ 9.624793] sd 6:0:0:0: [sde] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB)
[ 9.624799] sd 6:0:0:0: [sde] 4096-byte physical blocks
[ 9.624820] sd 6:0:0:0: [sde] Write Protect is off
[ 9.624823] sd 6:0:0:0: [sde] Mode Sense: 00 3a 00 00
[ 9.624857] sd 6:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.624891] sd 6:0:0:0: [sde] Preferred minimum I/O size 4096 bytes
[ 9.625190] sd 6:0:2:0: [sdg] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB)
[ 9.625194] sd 6:0:2:0: [sdg] 4096-byte physical blocks
[ 9.625206] sd 6:0:2:0: [sdg] Write Protect is off
[ 9.625209] sd 6:0:2:0: [sdg] Mode Sense: 00 3a 00 00
[ 9.625231] sd 6:0:2:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.625259] sd 6:0:2:0: [sdg] Preferred minimum I/O size 4096 bytes
[ 9.625676] sd 6:0:3:0: [sdh] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB)
[ 9.625679] sd 6:0:3:0: [sdh] 4096-byte physical blocks
[ 9.625693] sd 6:0:3:0: [sdh] Write Protect is off
[ 9.625695] sd 6:0:3:0: [sdh] Mode Sense: 00 3a 00 00
[ 9.625985] sd 6:0:3:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.626006] sd 6:0:3:0: [sdh] Preferred minimum I/O size 4096 bytes
[ 9.626504] sd 6:0:5:0: [sdj] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB)
[ 9.626507] sd 6:0:5:0: [sdj] 4096-byte physical blocks
[ 9.626508] sd 6:0:4:0: [sdi] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB)
[ 9.626518] sd 6:0:4:0: [sdi] Write Protect is off
[ 9.626520] sd 6:0:4:0: [sdi] Mode Sense: 00 3a 00 00
[ 9.626527] sd 6:0:5:0: [sdj] Write Protect is off
[ 9.626529] sd 6:0:5:0: [sdj] Mode Sense: 00 3a 00 00
[ 9.626534] sd 6:0:4:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.626548] sd 6:0:5:0: [sdj] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.626553] sd 6:0:4:0: [sdi] Preferred minimum I/O size 512 bytes
[ 9.626687] sd 6:0:5:0: [sdj] Preferred minimum I/O size 4096 bytes
[ 9.668709] sdf: sdf1 sdf9
[ 9.668954] sdh: sdh1 sdh9
[ 9.669188] sd 6:0:1:0: [sdf] Attached SCSI disk
[ 9.669502] sdj: sdj1 sdj9
[ 9.669648] sd 6:0:3:0: [sdh] Attached SCSI disk
[ 9.669737] sd 6:0:5:0: [sdj] Attached SCSI disk
[ 9.673723] sdg: sdg1 sdg9
[ 9.673896] sd 6:0:2:0: [sdg] Attached SCSI disk
[ 9.680073] sde: sde1 sde9
[ 9.680402] sd 6:0:0:0: [sde] Attached SCSI disk
[ 9.838673] random: crng init done
[ 9.874252] sdi: sdi1 sdi9
[ 9.874615] sd 6:0:4:0: [sdi] Attached SCSI disk
[ 9.911032] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 9.911037] sas: ata8: end_device-6:1: cmd error handler
[ 9.911052] sas: ata7: end_device-6:0: dev error handler
[ 9.911061] sas: ata8: end_device-6:1: dev error handler
[ 9.911070] sas: ata9: end_device-6:2: dev error handler
[ 9.911074] sas: ata10: end_device-6:3: dev error handler
[ 9.911077] sas: ata11: end_device-6:4: dev error handler
[ 9.911080] sas: ata12: end_device-6:5: dev error handler
[ 9.911434] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 1 tries: 1
[ 9.927595] sas: Enter sas_scsi_recover_host busy: 5 failed: 5
[ 9.927600] sas: ata12: end_device-6:5: cmd error handler
[ 9.927603] sas: ata10: end_device-6:3: cmd error handler
[ 9.927606] sas: ata9: end_device-6:2: cmd error handler
[ 9.927608] sas: ata11: end_device-6:4: cmd error handler
[ 9.927617] sas: ata7: end_device-6:0: cmd error handler
[ 9.927652] sas: ata7: end_device-6:0: dev error handler
[ 9.927656] sas: ata8: end_device-6:1: dev error handler
[ 9.927661] sas: ata9: end_device-6:2: dev error handler
[ 9.927670] sas: ata11: end_device-6:4: dev error handler
[ 9.927670] sas: ata10: end_device-6:3: dev error handler
[ 9.927676] sas: ata12: end_device-6:5: dev error handler
[ 9.927684] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 5 tries: 1
[ 10.360256] initramfs: :: running hook [keymap]
[ 10.366566] initramfs: :: Loading keymap...done.
[ 10.368431] initramfs: :: running hook [consolefont]
[ 10.386916] initramfs: :: Loading console font...a\x08 \x08done.
[ 10.388802] initramfs: :: running hook [zfs-keys]
[ 10.390448] initramfs: Mounting ZFS root key device...
[ 10.487361] initramfs: :: running hook [zfs]
[ 11.328545] initramfs: ZFS: Importing pool arch.
[ 12.204483] zd0: p1 p2 p3 p4
[ 12.328113] initramfs: :: running late hook [zfs-keys]
[ 12.329676] initramfs: Unmounting ZFS root key device...
[ 20.484611] initramfs: :: running cleanup hook [udev]
[ 20.512397] printk: init: 1 output lines suppressed due to ratelimiting
[ 20.765963] systemd[1]: systemd 256.7-1-arch running in system mode (+PAM +AUDIT -SELINUX -APPARMOR -IMA +SMACK +SECCOMP +GCRYPT +GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBCRYPTSETUP_PLUGINS +LIBFDISK +PCRE2 +PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD +BPF_FRAMEWORK +XKBCOMMON +UTMP -SYSVINIT +LIBARCHIVE)
[ 20.765983] systemd[1]: Detected architecture x86-64.
[ 20.768438] systemd[1]: Hostname set to <server>.
[ 20.859376] systemd[1]: memfd_create() called without MFD_EXEC or MFD_NOEXEC_SEAL set
[ 21.254573] systemd[1]: bpf-restrict-fs: LSM BPF program attached
[ 21.386855] systemd-ssh-generator[884]: Binding SSH to AF_UNIX socket /run/ssh-unix-local/socket.
[ 21.386862] systemd-ssh-generator[884]: → connect via 'ssh .host' locally
[ 21.659992] systemd[1]: Queued start job for default target Multi-User System.
[ 21.700672] systemd[1]: Created slice Slice /system/dirmngr.
[ 21.701445] systemd[1]: Created slice Slice /system/getty.
[ 21.702077] systemd[1]: Created slice Slice /system/gpg-agent.
[ 21.702712] systemd[1]: Created slice Slice /system/gpg-agent-browser.
[ 21.703343] systemd[1]: Created slice Slice /system/gpg-agent-extra.
[ 21.703962] systemd[1]: Created slice Slice /system/gpg-agent-ssh.
[ 21.704619] systemd[1]: Created slice Slice /system/keyboxd.
[ 21.705274] systemd[1]: Created slice Slice /system/lxc.
[ 21.705926] systemd[1]: Created slice Slice /system/modprobe.
[ 21.706579] systemd[1]: Created slice Slice /system/syncthing.
[ 21.707246] systemd[1]: Created slice Encrypted Volume Units Service Slice.
[ 21.707923] systemd[1]: Created slice Slice /system/systemd-fsck.
[ 21.708416] systemd[1]: Created slice User and Session Slice.
[ 21.708620] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 21.708762] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 21.709123] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 21.709247] systemd[1]: Expecting device /dev/disk/by-label/BOOT...
[ 21.709323] systemd[1]: Expecting device /dev/disk/by-partuuid/5b523a3f-2c62-4cd1-a57f-3c99ba765f1c...
[ 21.709396] systemd[1]: Expecting device /dev/mapper/swap...
[ 21.709482] systemd[1]: Reached target Local Integrity Protected Volumes.
[ 21.709586] systemd[1]: Reached target Path Units.
[ 21.709671] systemd[1]: Reached target Remote File Systems.
[ 21.709760] systemd[1]: Reached target Slice Units.
[ 21.709849] systemd[1]: Reached target System Time Set.
[ 21.709939] systemd[1]: Reached target Local Verity Protected Volumes.
[ 21.710214] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ 21.710446] systemd[1]: Listening on LVM2 poll daemon socket.
[ 21.715054] systemd[1]: Listening on RPCbind Server Activation Socket.
[ 21.715225] systemd[1]: Reached target RPC Port Mapper.
[ 21.717338] systemd[1]: Listening on Process Core Dump Socket.
[ 21.718707] systemd[1]: Listening on Credential Encryption/Decryption.
[ 21.718919] systemd[1]: Listening on Journal Socket (/dev/log).
[ 21.719123] systemd[1]: Listening on Journal Sockets.
[ 21.719363] systemd[1]: Listening on Network Service Netlink Socket.
[ 21.720453] systemd[1]: TPM PCR Measurements was skipped because of an unmet condition check (ConditionSecurity=measured-uki).
[ 21.720480] systemd[1]: Make TPM PCR Policy was skipped because of an unmet condition check (ConditionSecurity=measured-uki).
[ 21.720611] systemd[1]: Listening on udev Control Socket.
[ 21.721729] systemd[1]: Listening on udev Kernel Socket.
[ 21.726575] systemd[1]: Mounting Huge Pages File System...
[ 21.731028] systemd[1]: Mounting POSIX Message Queue File System...
[ 21.751392] systemd[1]: Mounting NFSD configuration filesystem...
[ 21.756329] systemd[1]: Mounting Kernel Debug File System...
[ 21.762057] systemd[1]: Mounting Kernel Trace File System...
[ 21.762826] systemd[1]: Kernel Module supporting RPCSEC_GSS was skipped because of an unmet condition check (ConditionPathExists=/etc/krb5.keytab).
[ 21.767184] systemd[1]: Starting Create List of Static Device Nodes...
[ 21.772267] systemd[1]: Starting Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling...
[ 21.796202] systemd[1]: Starting Load Kernel Module configfs...
[ 21.801064] systemd[1]: Starting Load Kernel Module dm_mod...
[ 21.804140] systemd[1]: Starting Load Kernel Module drm...
[ 21.809496] systemd[1]: Starting Load Kernel Module fuse...
[ 21.817031] systemd[1]: Starting Load Kernel Module loop...
[ 21.821233] systemd[1]: Clear Stale Hibernate Storage Info was skipped because of an unmet condition check (ConditionPathExists=/sys/firmware/efi/efivars/HibernateLocation-8cf2644b-4b0b-428f-9387-6d876050dc67).
[ 21.851080] systemd[1]: Starting Journal Service...
[ 21.856615] fuse: init (API version 7.39)
[ 21.864021] RPC: Registered named UNIX socket transport module.
[ 21.864026] RPC: Registered udp transport module.
[ 21.864027] RPC: Registered tcp transport module.
[ 21.864028] RPC: Registered tcp-with-tls transport module.
[ 21.864029] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 21.864963] loop: module loaded
[ 21.871104] systemd[1]: Starting Load Kernel Modules...
[ 21.871744] systemd[1]: TPM PCR Machine ID Measurement was skipped because of an unmet condition check (ConditionSecurity=measured-uki).
[ 21.876033] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 21.878222] systemd[1]: Early TPM SRK Setup was skipped because of an unmet condition check (ConditionSecurity=measured-uki).
[ 21.882313] systemd[1]: Starting Load udev Rules from Credentials...
[ 21.900277] systemd[1]: Starting Coldplug All udev Devices...
[ 21.907484] systemd[1]: Mounted Huge Pages File System.
[ 21.918216] systemd[1]: Mounted POSIX Message Queue File System.
[ 21.918934] systemd[1]: Mounted Kernel Debug File System.
[ 21.919618] systemd[1]: Mounted Kernel Trace File System.
[ 21.928168] device-mapper: uevent: version 1.0.3
[ 21.930904] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com
[ 21.935504] systemd[1]: Finished Create List of Static Device Nodes.
[ 21.940596] systemd[1]: modprobe@configfs.service: Deactivated successfully.
[ 21.947970] systemd[1]: Finished Load Kernel Module configfs.
[ 21.952261] systemd[1]: modprobe@dm_mod.service: Deactivated successfully.
[ 21.962261] sd 1:0:0:0: Attached scsi generic sg0 type 0
[ 21.962295] sd 4:0:0:0: Attached scsi generic sg1 type 0
[ 21.962327] sd 5:0:0:0: Attached scsi generic sg2 type 0
[ 21.962360] sd 7:0:0:0: Attached scsi generic sg3 type 0
[ 21.962390] sd 6:0:0:0: Attached scsi generic sg4 type 0
[ 21.962419] sd 6:0:1:0: Attached scsi generic sg5 type 0
[ 21.962446] sd 6:0:2:0: Attached scsi generic sg6 type 0
[ 21.962475] sd 6:0:3:0: Attached scsi generic sg7 type 0
[ 21.962504] sd 6:0:4:0: Attached scsi generic sg8 type 0
[ 21.962531] sd 6:0:5:0: Attached scsi generic sg9 type 0
[ 21.972637] systemd-journald[914]: Collecting audit messages is disabled.
[ 21.978130] systemd[1]: Finished Load Kernel Module dm_mod.
[ 21.979095] systemd[1]: modprobe@drm.service: Deactivated successfully.
[ 22.012309] systemd[1]: Finished Load Kernel Module drm.
[ 22.013424] systemd[1]: Mounted NFSD configuration filesystem.
[ 22.014276] systemd[1]: modprobe@fuse.service: Deactivated successfully.
[ 22.030019] vboxdrv: Found 2 processor cores/threads
[ 22.034588] systemd[1]: Finished Load Kernel Module fuse.
[ 22.035554] systemd[1]: modprobe@loop.service: Deactivated successfully.
[ 22.047866] systemd[1]: Finished Load Kernel Module loop.
[ 22.061287] systemd[1]: Finished Remount Root and Kernel File Systems.
[ 22.065048] vboxdrv: TSC mode is Invariant, tentative frequency 2693195346 Hz
[ 22.065052] vboxdrv: Successfully loaded version 7.1.2 r164945 (interface 0x00340001)
[ 22.070076] VBoxNetAdp: Successfully started.
[ 22.075715] systemd[1]: Finished Load udev Rules from Credentials.
[ 22.079029] systemd[1]: Mounting FUSE Control File System...
[ 22.079159] VBoxNetFlt: Successfully started.
[ 22.084230] systemd[1]: Mounting Kernel Configuration File System...
[ 22.094607] systemd[1]: Starting Rebuild Hardware Database...
[ 22.097950] systemd[1]: Starting Load/Save OS Random Seed...
[ 22.101530] systemd[1]: Repartition Root Disk was skipped because no trigger condition checks were met.
[ 22.104581] systemd[1]: Starting Create Static Device Nodes in /dev gracefully...
[ 22.111097] systemd[1]: TPM SRK Setup was skipped because of an unmet condition check (ConditionSecurity=measured-uki).
[ 22.122773] systemd[1]: Finished Load Kernel Modules.
[ 22.124757] systemd[1]: Mounted FUSE Control File System.
[ 22.126019] systemd[1]: Mounted Kernel Configuration File System.
[ 22.135035] systemd[1]: Starting Apply Kernel Variables...
[ 22.149859] systemd[1]: Started Journal Service.
[ 22.236408] systemd-journald[914]: Received client request to flush runtime journal.
[ 23.522188] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 23.522520] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 23.522762] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600'
[ 23.523883] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 23.523889] cfg80211: failed to load regulatory.db
[ 23.603808] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 23.716125] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 23.716130] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 23.721004] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 23.721012] sas: ata7: end_device-6:0: cmd error handler
[ 23.721027] sas: ata7: end_device-6:0: dev error handler
[ 23.721046] sas: ata8: end_device-6:1: dev error handler
[ 23.721051] sas: ata9: end_device-6:2: dev error handler
[ 23.721054] sas: ata10: end_device-6:3: dev error handler
[ 23.721058] sas: ata11: end_device-6:4: dev error handler
[ 23.721061] sas: ata12: end_device-6:5: dev error handler
[ 23.721067] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 1 tries: 1
[ 23.754503] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 23.754509] sas: ata8: end_device-6:1: cmd error handler
[ 23.754523] sas: ata7: end_device-6:0: dev error handler
[ 23.754534] sas: ata8: end_device-6:1: dev error handler
[ 23.754545] sas: ata9: end_device-6:2: dev error handler
[ 23.754549] sas: ata10: end_device-6:3: dev error handler
[ 23.754553] sas: ata11: end_device-6:4: dev error handler
[ 23.754556] sas: ata12: end_device-6:5: dev error handler
[ 23.754561] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 1 tries: 1
[ 23.787692] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 23.787699] sas: ata9: end_device-6:2: cmd error handler
[ 23.787714] sas: ata7: end_device-6:0: dev error handler
[ 23.787724] sas: ata8: end_device-6:1: dev error handler
[ 23.787728] sas: ata9: end_device-6:2: dev error handler
[ 23.787739] sas: ata10: end_device-6:3: dev error handler
[ 23.787743] sas: ata11: end_device-6:4: dev error handler
[ 23.787746] sas: ata12: end_device-6:5: dev error handler
[ 23.787752] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 1 tries: 1
[ 23.801075] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 23.801082] sas: ata12: end_device-6:5: cmd error handler
[ 23.801095] sas: ata7: end_device-6:0: dev error handler
[ 23.801105] sas: ata8: end_device-6:1: dev error handler
[ 23.801109] sas: ata9: end_device-6:2: dev error handler
[ 23.801112] sas: ata10: end_device-6:3: dev error handler
[ 23.801115] sas: ata11: end_device-6:4: dev error handler
[ 23.801118] sas: ata12: end_device-6:5: dev error handler
[ 23.801130] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 1 tries: 1
[ 23.821746] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 23.821753] sas: ata10: end_device-6:3: cmd error handler
[ 23.821766] sas: ata7: end_device-6:0: dev error handler
[ 23.821774] sas: ata8: end_device-6:1: dev error handler
[ 23.821777] sas: ata9: end_device-6:2: dev error handler
[ 23.821780] sas: ata10: end_device-6:3: dev error handler
[ 23.821790] sas: ata11: end_device-6:4: dev error handler
[ 23.821793] sas: ata12: end_device-6:5: dev error handler
[ 23.821800] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 1 tries: 1
[ 23.830444] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 23.830451] sas: ata11: end_device-6:4: cmd error handler
[ 23.830466] sas: ata7: end_device-6:0: dev error handler
[ 23.830474] sas: ata8: end_device-6:1: dev error handler
[ 23.830478] sas: ata9: end_device-6:2: dev error handler
[ 23.830481] sas: ata10: end_device-6:3: dev error handler
[ 23.830484] sas: ata11: end_device-6:4: dev error handler
[ 23.830493] sas: ata12: end_device-6:5: dev error handler
[ 23.830500] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 1 tries: 1
[ 24.164638] Key type encrypted registered
[ 24.195353] ACPI Warning: SystemIO range 0x0000000000000428-0x000000000000042F conflicts with OpRegion 0x0000000000000400-0x000000000000047F (\PMIO) (20230628/utaddress-204)
[ 24.195362] ACPI: OSL: Resource conflict; ACPI support missing from driver?
[ 24.195366] ACPI Warning: SystemIO range 0x0000000000000540-0x000000000000054F conflicts with OpRegion 0x0000000000000500-0x000000000000057F (\_SB.PCI0.LPCB.GPBX) (20230628/utaddress-204)
[ 24.195370] ACPI Warning: SystemIO range 0x0000000000000540-0x000000000000054F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20230628/utaddress-204)
[ 24.195372] ACPI: OSL: Resource conflict; ACPI support missing from driver?
[ 24.195374] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053F conflicts with OpRegion 0x0000000000000500-0x000000000000057F (\_SB.PCI0.LPCB.GPBX) (20230628/utaddress-204)
[ 24.195377] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20230628/utaddress-204)
[ 24.195379] ACPI: OSL: Resource conflict; ACPI support missing from driver?
[ 24.195380] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052F conflicts with OpRegion 0x0000000000000500-0x000000000000057F (\_SB.PCI0.LPCB.GPBX) (20230628/utaddress-204)
[ 24.195384] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052F conflicts with OpRegion 0x0000000000000500-0x000000000000050F (\_GPE.GPIO) (20230628/utaddress-204)
[ 24.195387] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20230628/utaddress-204)
[ 24.195389] ACPI: OSL: Resource conflict; ACPI support missing from driver?
[ 24.195390] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 24.231332] e1000e: Intel(R) PRO/1000 Network Driver
[ 24.231337] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 24.231588] e1000e 0000:03:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[ 24.286368] i801_smbus 0000:00:1f.3: SMBus using PCI interrupt
[ 24.286877] i2c i2c-7: 2/2 memory slots populated (from DMI)
[ 24.287002] e1000e 0000:03:00.0 0000:03:00.0 (uninitialized): registered PHC clock
[ 24.316739] input: PC Speaker as /devices/platform/pcspkr/input/input3
[ 24.331770] i2c i2c-7: Successfully instantiated SPD at 0x50
[ 24.378967] e1000e 0000:03:00.0 eth0: (PCI Express:2.5GT/s:Width x1) 68:05:ca:04:13:15
[ 24.378974] e1000e 0000:03:00.0 eth0: Intel(R) PRO/1000 Network Connection
[ 24.378989] e1000e 0000:03:00.0 eth0: MAC: 3, PHY: 8, PBA No: E46981-007
[ 24.399528] r8169 0000:04:00.0: can't disable ASPM; OS doesn't have ASPM control
[ 24.421568] RAPL PMU: API unit is 2^-32 Joules, 3 fixed counters, 163840 ms ovfl timer
[ 24.421574] RAPL PMU: hw unit of domain pp0-core 2^-16 Joules
[ 24.421576] RAPL PMU: hw unit of domain package 2^-16 Joules
[ 24.421577] RAPL PMU: hw unit of domain pp1-gpu 2^-16 Joules
[ 24.454364] i8042: PNP: No PS/2 controller found.
[ 24.454369] i8042: Probing ports directly.
[ 24.458682] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 24.458691] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 24.474846] r8169 0000:04:00.0 eth1: RTL8168evl/8111evl, 14:da:e9:94:00:02, XID 2c9, IRQ 34
[ 24.474854] r8169 0000:04:00.0 eth1: jumbo features [frames: 9194 bytes, tx checksumming: ko]
[ 24.568751] cryptd: max_cpu_qlen set to 1000
[ 24.685462] iTCO_vendor_support: vendor-support=0
[ 24.690177] at24 7-0050: supply vcc not found, using dummy regulator
[ 24.695739] at24 7-0050: 256 byte spd EEPROM, read-only
[ 24.714653] iTCO_wdt iTCO_wdt.1.auto: Found a Cougar Point TCO device (Version=2, TCOBASE=0x0460)
[ 24.715637] iTCO_wdt iTCO_wdt.1.auto: initialized. heartbeat=30 sec (nowayout=0)
[ 24.718140] r8169 0000:04:00.0 enp4s0: renamed from eth1
[ 24.718880] asus_wmi: ASUS WMI generic driver loaded
[ 24.744354] asus_wmi: Initialization: 0x0
[ 24.744391] asus_wmi: BIOS WMI version: 0.9
[ 24.744449] asus_wmi: SFUN value: 0x0
[ 24.744452] eeepc-wmi eeepc-wmi: Detected ASUSWMI, use DCTS
[ 24.746707] input: Eee PC WMI hotkeys as /devices/platform/eeepc-wmi/input/input4
[ 24.799786] e1000e 0000:03:00.0 enp3s0: renamed from eth0
[ 24.835232] br0: port 1(enp3s0) entered blocking state
[ 24.835239] br0: port 1(enp3s0) entered disabled state
[ 24.835262] e1000e 0000:03:00.0 enp3s0: entered allmulticast mode
[ 24.835318] e1000e 0000:03:00.0 enp3s0: entered promiscuous mode
[ 24.976732] Adding 4194300k swap on /dev/mapper/swap. Priority:-2 extents:1 across:4194300k SS
[ 24.990836] intel_rapl_common: Found RAPL domain package
[ 24.990841] intel_rapl_common: Found RAPL domain core
[ 24.990842] intel_rapl_common: Found RAPL domain uncore
[ 24.990850] intel_rapl_common: package-0:package:long_term locked by BIOS
[ 24.990852] intel_rapl_common: package-0:package:short_term locked by BIOS
[ 27.435247] e1000e 0000:03:00.0 enp3s0: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 27.437391] br0: port 1(enp3s0) entered blocking state
[ 27.437396] br0: port 1(enp3s0) entered forwarding state
[ 27.856564] nct6775: Found NCT6776D/F or compatible chip at 0x2e:0x290
[ 27.856580] ACPI Warning: SystemIO range 0x0000000000000295-0x0000000000000296 conflicts with OpRegion 0x0000000000000290-0x0000000000000299 (\_GPE.HWRE) (20230628/utaddress-204)
[ 27.856587] ACPI: OSL: Resource conflict; ACPI support missing from driver?
[ 28.050496] br0: port 2(vethGS5Ljh) entered blocking state
[ 28.050503] br0: port 2(vethGS5Ljh) entered disabled state
[ 28.050512] vethGS5Ljh: entered allmulticast mode
[ 28.050561] vethGS5Ljh: entered promiscuous mode
[ 28.050660] br0: port 2(vethGS5Ljh) entered blocking state
[ 28.050663] br0: port 2(vethGS5Ljh) entered forwarding state
[ 28.064277] eth0: renamed from vethm5gBRH
[ 28.457809] br0: port 2(vethGS5Ljh) entered disabled state
[ 30.843467] br0: port 2(vethGS5Ljh) entered blocking state
[ 30.843475] br0: port 2(vethGS5Ljh) entered forwarding state
[ 30.949488] systemd-journald[914]: Failed to set ACL on /var/log/journal/24e749b2dcda413aa59347d0a0109eff/user-1001.journal, ignoring: Operation not supported
[ 35.752223] RPC: Registered rdma transport module.
[ 35.752229] RPC: Registered rdma backchannel transport module.
[ 35.896411] NFSD: Using nfsdcld client tracking operations.
[ 35.896417] NFSD: no clients to reclaim, skipping NFSv4 grace period (net f0000000)
[ 42.043683] br-47a0501c2f0f: port 1(veth25f239f) entered blocking state
[ 42.043693] br-47a0501c2f0f: port 1(veth25f239f) entered disabled state
[ 42.043718] veth25f239f: entered allmulticast mode
[ 42.043788] veth25f239f: entered promiscuous mode
[ 42.044513] br-47a0501c2f0f: port 1(veth25f239f) entered blocking state
[ 42.044519] br-47a0501c2f0f: port 1(veth25f239f) entered forwarding state
[ 42.044609] br-47a0501c2f0f: port 1(veth25f239f) entered disabled state
[ 42.082406] br-47a0501c2f0f: port 2(veth08ea163) entered blocking state
[ 42.082414] br-47a0501c2f0f: port 2(veth08ea163) entered disabled state
[ 42.082430] veth08ea163: entered allmulticast mode
[ 42.082588] veth08ea163: entered promiscuous mode
[ 42.084680] br-47a0501c2f0f: port 2(veth08ea163) entered blocking state
[ 42.084687] br-47a0501c2f0f: port 2(veth08ea163) entered forwarding state
[ 42.085703] br-47a0501c2f0f: port 2(veth08ea163) entered disabled state
[ 42.125124] br-47a0501c2f0f: port 3(vethabc9d65) entered blocking state
[ 42.125130] br-47a0501c2f0f: port 3(vethabc9d65) entered disabled state
[ 42.125234] vethabc9d65: entered allmulticast mode
[ 42.125502] vethabc9d65: entered promiscuous mode
[ 42.125980] br-47a0501c2f0f: port 3(vethabc9d65) entered blocking state
[ 42.125984] br-47a0501c2f0f: port 3(vethabc9d65) entered forwarding state
[ 42.293100] br-47a0501c2f0f: port 4(veth3f03756) entered blocking state
[ 42.293107] br-47a0501c2f0f: port 4(veth3f03756) entered disabled state
[ 42.293119] veth3f03756: entered allmulticast mode
[ 42.302797] veth3f03756: entered promiscuous mode
[ 42.303006] br-47a0501c2f0f: port 4(veth3f03756) entered blocking state
[ 42.303011] br-47a0501c2f0f: port 4(veth3f03756) entered forwarding state
[ 42.444668] br-47a0501c2f0f: port 5(vetha58e488) entered blocking state
[ 42.444675] br-47a0501c2f0f: port 5(vetha58e488) entered disabled state
[ 42.444698] vetha58e488: entered allmulticast mode
[ 42.458367] vetha58e488: entered promiscuous mode
[ 42.467886] br-47a0501c2f0f: port 5(vetha58e488) entered blocking state
[ 42.467893] br-47a0501c2f0f: port 5(vetha58e488) entered forwarding state
[ 42.484156] br-47a0501c2f0f: port 3(vethabc9d65) entered disabled state
[ 42.484212] br-47a0501c2f0f: port 4(veth3f03756) entered disabled state
[ 42.484252] br-47a0501c2f0f: port 5(vetha58e488) entered disabled state
[ 44.279232] eth0: renamed from vethcf7ed66
[ 44.301538] br-47a0501c2f0f: port 4(veth3f03756) entered blocking state
[ 44.301546] br-47a0501c2f0f: port 4(veth3f03756) entered forwarding state
[ 44.319336] eth0: renamed from veth9a9555b
[ 44.352067] eth0: renamed from vethf3f6ee6
[ 44.365576] br-47a0501c2f0f: port 2(veth08ea163) entered blocking state
[ 44.365585] br-47a0501c2f0f: port 2(veth08ea163) entered forwarding state
[ 44.380841] eth0: renamed from veth8345ec5
[ 44.387938] br-47a0501c2f0f: port 5(vetha58e488) entered blocking state
[ 44.387947] br-47a0501c2f0f: port 5(vetha58e488) entered forwarding state
[ 44.396667] br-47a0501c2f0f: port 1(veth25f239f) entered blocking state
[ 44.396676] br-47a0501c2f0f: port 1(veth25f239f) entered forwarding state
[ 44.442330] eth0: renamed from vethae9f536
[ 44.456548] br-47a0501c2f0f: port 3(vethabc9d65) entered blocking state
[ 44.456558] br-47a0501c2f0f: port 3(vethabc9d65) entered forwarding state
[ 67.980214] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 67.980222] sas: ata7: end_device-6:0: cmd error handler
[ 67.980238] sas: ata7: end_device-6:0: dev error handler
[ 67.980256] sas: ata8: end_device-6:1: dev error handler
[ 67.980260] sas: ata9: end_device-6:2: dev error handler
[ 67.980263] sas: ata10: end_device-6:3: dev error handler
[ 67.980266] sas: ata11: end_device-6:4: dev error handler
[ 67.980269] sas: ata12: end_device-6:5: dev error handler
[ 67.980276] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 1 tries: 1
[ 68.030140] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 68.030148] sas: ata7: end_device-6:0: cmd error handler
[ 68.030165] sas: ata7: end_device-6:0: dev error handler
[ 68.030190] sas: ata8: end_device-6:1: dev error handler
[ 68.030197] sas: ata9: end_device-6:2: dev error handler
[ 68.030200] sas: ata10: end_device-6:3: dev error handler
[ 68.030204] sas: ata11: end_device-6:4: dev error handler
[ 68.030207] sas: ata12: end_device-6:5: dev error handler
[ 68.030236] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 1 tries: 1
[ 831.632643] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 831.632655] sas: ata7: end_device-6:0: cmd error handler
[ 831.632680] sas: ata7: end_device-6:0: dev error handler
[ 831.632688] sas: ata8: end_device-6:1: dev error handler
[ 831.632703] sas: ata9: end_device-6:2: dev error handler
[ 831.632708] sas: ata10: end_device-6:3: dev error handler
[ 831.632713] sas: ata11: end_device-6:4: dev error handler
[ 831.632718] sas: ata12: end_device-6:5: dev error handler
[ 831.632741] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 1 tries: 1
[ 843.899180] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 843.899191] sas: ata7: end_device-6:0: cmd error handler
[ 843.899215] sas: ata7: end_device-6:0: dev error handler
[ 843.899228] sas: ata8: end_device-6:1: dev error handler
[ 843.899237] sas: ata9: end_device-6:2: dev error handler
[ 843.899241] sas: ata10: end_device-6:3: dev error handler
[ 843.899245] sas: ata11: end_device-6:4: dev error handler
[ 843.899248] sas: ata12: end_device-6:5: dev error handler
[ 843.899255] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 1 tries: 1
[ 873.175495] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 873.175505] sas: ata7: end_device-6:0: cmd error handler
[ 873.175562] sas: ata7: end_device-6:0: dev error handler
[ 873.175585] sas: ata8: end_device-6:1: dev error handler
[ 873.175590] sas: ata9: end_device-6:2: dev error handler
[ 873.175594] sas: ata10: end_device-6:3: dev error handler
[ 873.175598] sas: ata11: end_device-6:4: dev error handler
[ 873.175599] sas: ata12: end_device-6:5: dev error handler
[ 873.175613] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 1 tries: 1
[ 894.521901] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 894.521912] sas: ata7: end_device-6:0: cmd error handler
[ 894.521951] sas: ata7: end_device-6:0: dev error handler
[ 894.521965] sas: ata8: end_device-6:1: dev error handler
[ 894.521974] sas: ata9: end_device-6:2: dev error handler
[ 894.521975] sas: ata10: end_device-6:3: dev error handler
[ 894.521979] sas: ata11: end_device-6:4: dev error handler
[ 894.521979] sas: ata12: end_device-6:5: dev error handler
[ 894.522529] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 1 tries: 1
[ 914.663878] drivers/scsi/mvsas/mv_sas.c 1585:port 1 slot 65 rx_desc 30041 has error info0000000001000000.
[ 914.691706] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 914.691715] sas: ata7: end_device-6:0: cmd error handler
[ 914.691785] sas: ata7: end_device-6:0: dev error handler
[ 914.691824] sas: ata8: end_device-6:1: dev error handler
[ 914.691846] sas: ata9: end_device-6:2: dev error handler
[ 914.691853] sas: ata10: end_device-6:3: dev error handler
[ 914.691859] sas: ata11: end_device-6:4: dev error handler
[ 914.691863] sas: ata12: end_device-6:5: dev error handler
[ 914.933350] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 1 tries: 1
[ 914.968276] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 914.968286] sas: ata7: end_device-6:0: cmd error handler
[ 914.968361] sas: ata7: end_device-6:0: dev error handler
[ 914.968388] sas: ata8: end_device-6:1: dev error handler
[ 914.968396] sas: ata9: end_device-6:2: dev error handler
[ 914.968401] sas: ata10: end_device-6:3: dev error handler
[ 914.968406] sas: ata11: end_device-6:4: dev error handler
[ 914.968410] sas: ata12: end_device-6:5: dev error handler
[ 914.968426] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 1 tries: 1
[ 915.104937] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 915.104947] sas: ata7: end_device-6:0: cmd error handler
[ 915.105012] sas: ata7: end_device-6:0: dev error handler
[ 915.105029] sas: ata8: end_device-6:1: dev error handler
[ 915.105034] sas: ata9: end_device-6:2: dev error handler
[ 915.105038] sas: ata10: end_device-6:3: dev error handler
[ 915.105042] sas: ata11: end_device-6:4: dev error handler
[ 915.105045] sas: ata12: end_device-6:5: dev error handler
[ 915.105050] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 1 tries: 1
[ 922.221546] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 922.221557] sas: ata7: end_device-6:0: cmd error handler
[ 922.221609] sas: ata7: end_device-6:0: dev error handler
[ 922.221633] sas: ata8: end_device-6:1: dev error handler
[ 922.221638] sas: ata9: end_device-6:2: dev error handler
[ 922.221643] sas: ata11: end_device-6:4: dev error handler
[ 922.221643] sas: ata10: end_device-6:3: dev error handler
[ 922.221647] sas: ata12: end_device-6:5: dev error handler
[ 922.221655] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 1 tries: 1
[ 958.361156] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 958.361176] sas: ata7: end_device-6:0: cmd error handler
[ 958.361246] sas: ata7: end_device-6:0: dev error handler
[ 958.361277] sas: ata8: end_device-6:1: dev error handler
[ 958.361286] sas: ata9: end_device-6:2: dev error handler
[ 958.361296] sas: ata11: end_device-6:4: dev error handler
[ 958.361296] sas: ata10: end_device-6:3: dev error handler
[ 958.361302] sas: ata12: end_device-6:5: dev error handler
[ 958.361332] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 1 tries: 1
[ 968.900576] drivers/scsi/mvsas/mv_sas.c 1585:port 1 slot 41 rx_desc 30029 has error info0000000001000000.
[ 968.930926] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 968.930936] sas: ata7: end_device-6:0: cmd error handler
[ 968.931008] sas: ata7: end_device-6:0: dev error handler
[ 968.931047] sas: ata8: end_device-6:1: dev error handler
[ 968.931070] sas: ata9: end_device-6:2: dev error handler
[ 968.931083] sas: ata10: end_device-6:3: dev error handler
[ 968.931087] sas: ata12: end_device-6:5: dev error handler
[ 968.931087] sas: ata11: end_device-6:4: dev error handler
[ 968.931157] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 1 tries: 1
[ 968.977610] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 968.977620] sas: ata7: end_device-6:0: cmd error handler
[ 968.977671] sas: ata7: end_device-6:0: dev error handler
[ 968.977687] sas: ata8: end_device-6:1: dev error handler
[ 968.977702] sas: ata9: end_device-6:2: dev error handler
[ 968.977709] sas: ata11: end_device-6:4: dev error handler
[ 968.977709] sas: ata10: end_device-6:3: dev error handler
[ 968.977715] sas: ata12: end_device-6:5: dev error handler
[ 968.977728] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 1 tries: 1
[ 969.107688] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 969.107707] sas: ata7: end_device-6:0: cmd error handler
[ 969.107769] sas: ata7: end_device-6:0: dev error handler
[ 969.107796] sas: ata8: end_device-6:1: dev error handler
[ 969.107804] sas: ata9: end_device-6:2: dev error handler
[ 969.107810] sas: ata10: end_device-6:3: dev error handler
[ 969.107815] sas: ata11: end_device-6:4: dev error handler
[ 969.107821] sas: ata12: end_device-6:5: dev error handler
[ 969.107904] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 1 tries: 1Since this is a machine with noisy logs, I cannot provide some things like journalctl -b.
Offline
#2 2024-10-13 20:10:39
- gromit
- Package Maintainer (PM)
- From: Germany
- Registered: 2024-02-10
- Posts: 784
- Website
Re: Recent problem with smartctl + mvsas: CHECK POWER MODE not implemented
A while ago I have reported a similar error against the ATA subsystem in the kernel: https://lore.kernel.org/all/0bf3f2f0-0f … @heusel.eu
Could please verify again that the problem occurs on your hardware with the versions you have specified as broken? Also it would be good if you could narrow it down further by upgrading one version at a time via https://archive.archlinux.org/packages/l/linux-lts/
This could start out investigating, I will check my NAS in the meantime if it shows similar behaviour ..
Edit: Can't repro on my NAS, but my setup there is also quite different enough so I'd say this does not matter.
Last edited by gromit (2024-10-13 20:13:25)
Offline
#3 2024-10-14 19:25:51
- flauschig
- Member
- Registered: 2024-10-13
- Posts: 8
Re: Recent problem with smartctl + mvsas: CHECK POWER MODE not implemented
Thank you, I was not aware of this archive, I’ll try it asap!
Offline
#4 2024-10-16 19:17:41
- flauschig
- Member
- Registered: 2024-10-13
- Posts: 8
Re: Recent problem with smartctl + mvsas: CHECK POWER MODE not implemented
(If anyone else tries this: don’t forget to deal with the kernel headers package, too!)
Tested:
6.6.49-1: smartctl -n standby --attributes /dev/sde works
6.6.50-1: works
6.6.50-2: works
6.6.51-1: broken (as described in first post)
6.6.52-1: broken (same)
I can see in the 6.6.51 release notes that changes were made to libata. I also discovered the smartctl -r option, so here’s the (relevant) output:
$ sudo smartctl -r ioctl,2 -n standby --attributes /dev/sde
smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.6.52-1-lts] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
sde -> /sys/class/scsi_host/host6/proc_name: "(null)"
/dev/sde [SAT]: Device open changed type from 'scsi' to 'sat'
REPORT-IOCTL: Device=/dev/sde Command=CHECK POWER MODE
Input: FR=...., SC=...., LL=...., LM=...., LH=...., DEV=...., CMD=0xe5
status=2: sense_key=0 asc=0 ascq=0
[Duration: 0.025714s]
CHECK POWER MODE: incomplete response, ATA output registers missing
REPORT-IOCTL: Device=/dev/sde Command=CHECK POWER MODE returned -1 errno=38 [Function not implemented]
Sector Count Register (BASE-16): 00
CHECK POWER MODE not implemented, ignoring -n option…not that I can understand the problem. From the smartmontools source code, it would appear this output is the result of no output data (out.out_regs.is_set() returns false). Why though?
---
How would I go about bisecting the Arch kernel package? Using the linux-git AUR package and the bisect guide and then just roll with it? Or is there some special procedure because I’m using the LTS kernel?
Offline
#5 2024-10-17 12:51:56
- gromit
- Package Maintainer (PM)
- From: Germany
- Registered: 2024-02-10
- Posts: 784
- Website
Re: Recent problem with smartctl + mvsas: CHECK POWER MODE not implemented
So there are only a handful of commits that are ata related in the changes for these versions, of which the first two look especially relevant IMO:
$ git log --pretty=oneline v6.6.50..v6.6.51 | grep ata:
872f86e1757bbb0a334ee739b824e47c448f5ebc ata: libata-scsi: Check ATA_QCFLAG_RTF_FILLED before using result_tf
c8d4acb325302fd832e10d5ba17b1b8eba9d08f9 ata: libata-scsi: Remove redundant sense_buffer memsets
b777131d03be76594849da084a14853f72cf0e37 ata: pata_macio: Use WARN instead of BUG
c0fbc9593b18b9d7ad0ad500f2ff55bbbf8ab2a2 ata: libata: Fix memory leak for error path in ata_host_alloc()If you want you could try the following build that has the first one reverted:
sudo pacman -U https://pkgbuild.com/\~gromit/linux-bisection-kernels/linux-lts-6.6.51-1.1-x86_64.pkg.tar.zstAnd this image has the first and the second one reverted (they apparently depended on each other since I got a merge conflict):
sudo pacman -U https://pkgbuild.com/\~gromit/linux-bisection-kernels/linux-lts-6.6.51-1.2-x86_64.pkg.tar.zstIf all that does not help we can do a proper bisection 
Also it would be interesting to see if the issue also is present in the latest mainline release candidate:
sudo pacman -U https://pkgbuild.com/\~gromit/linux-bisection-kernels/linux-mainline-6.12rc3-1-x86_64.pkg.tar.zstOffline
#6 2024-10-17 18:59:09
- flauschig
- Member
- Registered: 2024-10-13
- Posts: 8
Re: Recent problem with smartctl + mvsas: CHECK POWER MODE not implemented
Thank you for providing these builds! Unfortunately I cannot use them as-is, I also need the corresponding headers packages for my DKMS modules.
And that is also why I won’t be able to easily test newer kernels: My entire system is on ZFS and ZFS is only compatible up to 6.9 at the moment. I could try with a live USB, it wouldn’t necessarily have to be Arch either. I’m not familiar with any distro so far ahead though, that’s not my area of interest. :-)
Offline
#7 2024-10-17 19:04:19
- gromit
- Package Maintainer (PM)
- From: Germany
- Registered: 2024-02-10
- Posts: 784
- Website
Re: Recent problem with smartctl + mvsas: CHECK POWER MODE not implemented
The corresponding header packages are also uploaded next to the kernel image, just also install them like so:
sudo pacman -U https://pkgbuild.com/\~gromit/linux-bisection-kernels/linux-lts-6.6.51-1.1-x86_64.pkg.tar.zst https://pkgbuild.com/\~gromit/linux-bisection-kernels/linux-lts-headers-6.6.51-1.1-x86_64.pkg.tar.zstOffline
#8 2024-10-17 19:57:15
- flauschig
- Member
- Registered: 2024-10-13
- Posts: 8
Re: Recent problem with smartctl + mvsas: CHECK POWER MODE not implemented
I found the current Fedora Rawhide build to have a sufficiently recent kernel: 6.12.0 (27cc6fdf7201). It does not have this issue. smartctl works as expected.
I also tried the builds you provided:
6.6.51-1.1: works
6.6.51-1.2: works
So the first commit is likely causing this. I don’t get it though. If the changed code is triggered, it should always print a debug message, but I never saw them. Are debug messages somehow hidden by default and I need to enable them in /proc/sys/kernel/printk or something?
Offline
#9 2024-10-17 20:09:12
- gromit
- Package Maintainer (PM)
- From: Germany
- Registered: 2024-02-10
- Posts: 784
- Website
Re: Recent problem with smartctl + mvsas: CHECK POWER MODE not implemented
I think you can enable them either via "/proc/sys/kernel/printk" or by setting "loglevel=7". I guess we need KERN_DEBUG for this message to be displayed.
https://linuxconfig.org/introduction-to … log-levels
Offline
#10 2024-10-17 20:29:11
- flauschig
- Member
- Registered: 2024-10-13
- Posts: 8
Re: Recent problem with smartctl + mvsas: CHECK POWER MODE not implemented
Hm that appears not to work. I did this:
# echo 7 > /proc/sys/kernel/printk
# cat /proc/sys/kernel/printk
7 4 1 4What’s visible in /proc/kmsg or dmesg doesn’t change though. It does change what’s printed on the physical console. The only related output I get is this:
<5>[ 529.950200] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
<7>[ 529.950929] sas: ata7: end_device-6:0: cmd error handler
<7>[ 529.950973] sas: ata7: end_device-6:0: dev error handler
<7>[ 529.950992] sas: ata8: end_device-6:1: dev error handler
<7>[ 529.950998] sas: ata9: end_device-6:2: dev error handler
<7>[ 529.951002] sas: ata10: end_device-6:3: dev error handler
<7>[ 529.951006] sas: ata11: end_device-6:4: dev error handler
<7>[ 529.951010] sas: ata12: end_device-6:5: dev error handler
<5>[ 529.951142] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 1 tries: 1Just like before.
Last edited by flauschig (2024-10-17 20:29:46)
Offline
#11 2024-10-17 22:04:44
- loqs
- Member
- Registered: 2014-03-06
- Posts: 18,151
Re: Recent problem with smartctl + mvsas: CHECK POWER MODE not implemented
Arch kernels use dynamic debug.
Offline
#12 2024-10-18 16:43:23
- flauschig
- Member
- Registered: 2024-10-13
- Posts: 8
Re: Recent problem with smartctl + mvsas: CHECK POWER MODE not implemented
Alright! Now I finally have the actual branch that fails:
<7>[73893.586148] ata7.00: missing result TF: can't generate ATA PT sense data
<7>[73893.586159] ata7.00: missing result TF: can't set ATA PT sense fieldsThank you very much.
It’s not entirely clear to me were I would file a bug though. Against smartmontools? Or against the kernel?
Offline
#13 2024-10-19 08:18:12
- gromit
- Package Maintainer (PM)
- From: Germany
- Registered: 2024-02-10
- Posts: 784
- Website
Re: Recent problem with smartctl + mvsas: CHECK POWER MODE not implemented
I think this is appropriate to file against the kernel, this is the relevant documentation: https://docs.kernel.org/admin-guide/rep … sions.html
See for example the report I have mentioned in my initial posting (https://lore.kernel.org/all/0bf3f2f0-0f … heusel.eu/) for how this should look.
If you need any help in writing the report feel free to ask here! Also if you want I can file the report for you 
Offline
#14 2024-10-20 16:29:15
- flauschig
- Member
- Registered: 2024-10-13
- Posts: 8
Re: Recent problem with smartctl + mvsas: CHECK POWER MODE not implemented
I think filing it myself is more appropriate, since I’m in a position to test potential fixes.
Thank you for your support so far! I’ll mark this thread as solved after I file the report.
Offline
#15 2024-10-20 16:38:20
- gromit
- Package Maintainer (PM)
- From: Germany
- Registered: 2024-02-10
- Posts: 784
- Website
Re: Recent problem with smartctl + mvsas: CHECK POWER MODE not implemented
Noice! Looking forward to your report!
Offline