You are not logged in.
- Topics: Active | Unanswered
#1 2025-07-02 18:33:50
- Energy0120
- Member
- Registered: 2025-07-02
- Posts: 8
[SOLVED] Problems with Network on a fresh install.
I have read through many people sharing the same issue but couldn't really get to a solution... This is my first post in the forum so forgive me for formatting problems or anything, just let me know.
The problem, for what i have been able to understand, is that the module for my network drivers isn't being loaded, for some reason. I do not understand 100% how all drivers work, but i'll try to be as informative as i can on the issue.
I got to understand that the module that is causing issues is e1000e.
$ lspci .nn | grep Ethernet
00:1f.6 Ethernet controller [0200]: Intel Corporation Ethernet Connection (17) I219-V [8086:1a1d] (rev 11) ip link and nmcli d do not show my network card.
$ dmesg | grep e1000e shows this:
[ 2.045499] e1000e: Intel(R) PRO/1000 Network Driver
[ 2.045501] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 2.045858] e1000e 0000:00:1f.6: enabling device (0000 -> 0002)
[ 2.046057] e1000e 0000:00:1f.6: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[ 2.287029] e1000e 0000:00:1f.6: The NVM Checksum Is Not Valid
[ 2.318779] e1000e 0000:00:1f.6: probe with driver e1000e failed with error -5I have tried using Intel's BootUtil tool to flash the card manually, this is what happens:
Error: Connection to QV driver failed - please reinstall it!
Intel(R) Ethernet Flash Firmware Utility
BootUtil version 1.43.08.0
Copyright (C) 2003-2025 Intel Corporation
Type BootUtil -? for help
Port Network Address Location Series WOL Flash Firmware Version
==== ============ ============== ======= === ========================== =======
1 D8BBC1DD0CBA 00000:000:31.6 Gigabit N/A FLASH Not PresentMy network card's leds are still turned on although it is not usable.
I am dual booting with windows and that is actually my biggest suspect. The card works on windows and i previously had installed wake on lan, for which i had to keep the card basically always busy receiving packets. I disabled all the settings from windows device manager and even updated the bios (which reset the settings).
Last edited by Energy0120 (2025-07-04 18:54:53)
Offline
#2 2025-07-02 20:08:53
- seth
- Member
- From: Don't DM me only for attention
- Registered: 2012-09-03
- Posts: 71,628
Re: [SOLVED] Problems with Network on a fresh install.
The NVM Checksum Is Not ValidI am dual booting with windows and that is actually my biggest suspect.
Rightfully so: 3rd link below. Mandatory.
Disable it (it's NOT the BIOS setting!) and reboot windows and linux twice for voodo reasons.
Basically the only alternative is that you lack https://archlinux.org/packages/core/any … are-intel/
Online
#3 2025-07-02 23:43:16
- Energy0120
- Member
- Registered: 2025-07-02
- Posts: 8
Re: [SOLVED] Problems with Network on a fresh install.
Hi seth,
thank you for the quick reply. You know, I've seen your name quite often while looking at other people experiencing this issue lol, so I appreciate a lot your help.
I've tried disabling fastboot, i am pretty sure it's disabled
I even tried reinstalling the linux-firmware package and rebooting a few times, still nothing.
Something else i tried was disabling and uninstalling the drivers from windows > reboot to arch, still no progress > reboot to windows, internet back on.
I'm really trying to understand what could be the issue here, i tried also updating drivers for the network card on windows.
Offline
#4 2025-07-03 01:19:50
- dakota
- Member
- Registered: 2016-05-20
- Posts: 415
Re: [SOLVED] Problems with Network on a fresh install.
Energy0120 wrote:
I even tried reinstalling the linux-firmware package..
But did you specifically install the linux-firmware-intel as Seth suggested?
Cheers,
"Before Enlightenment chop wood, carry water. After Enlightenment chop wood, carry water." -- Zen proverb
Offline
#5 2025-07-03 02:49:10
- Energy0120
- Member
- Registered: 2025-07-02
- Posts: 8
Re: [SOLVED] Problems with Network on a fresh install.
Yes, since it was already installed I had to uninstall the whole linux-firmware package, and then reinstalled all of them.
Offline
#6 2025-07-03 06:16:15
- seth
- Member
- From: Don't DM me only for attention
- Registered: 2012-09-03
- Posts: 71,628
Re: [SOLVED] Problems with Network on a fresh install.
Do you still end up w/ "The NVM Checksum Is Not Valid"?
Please post your complete system journal for the boot:
sudo journalctl -b | curl -F 'file=@-' 0x0.stOnline
#7 2025-07-03 12:33:17
- Energy0120
- Member
- Registered: 2025-07-02
- Posts: 8
Re: [SOLVED] Problems with Network on a fresh install.
The journal is in http://0x0.st/80px.txt.
or here as a code block:
lug 03 14:26:45 lyoko kernel: Linux version 6.15.4-arch2-1 (linux@archlinux) (gcc (GCC) 15.1.1 20250425, GNU ld (GNU Binutils) 2.44.0) #1 SMP PREEMPT_DYNAMIC Fri, 27 Jun 2025 16:35:07 +0000
lug 03 14:26:45 lyoko kernel: Command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=1d61a5b2-8700-4954-8d30-c4288198c34c rw loglevel=3 quiet
lug 03 14:26:45 lyoko kernel: x86/split lock detection: #AC: crashing the kernel on kernel split_locks and warning on user-space split_locks
lug 03 14:26:45 lyoko kernel: BIOS-provided physical RAM map:
lug 03 14:26:45 lyoko kernel: BIOS-e820: [mem 0x0000000000000000-0x000000000009dfff] usable
lug 03 14:26:45 lyoko kernel: BIOS-e820: [mem 0x000000000009e000-0x000000000009efff] reserved
lug 03 14:26:45 lyoko kernel: BIOS-e820: [mem 0x000000000009f000-0x000000000009ffff] usable
lug 03 14:26:45 lyoko kernel: BIOS-e820: [mem 0x00000000000a0000-0x00000000000fffff] reserved
lug 03 14:26:45 lyoko kernel: BIOS-e820: [mem 0x0000000000100000-0x0000000067ffffff] usable
lug 03 14:26:45 lyoko kernel: BIOS-e820: [mem 0x0000000068000000-0x0000000068bfffff] reserved
lug 03 14:26:45 lyoko kernel: BIOS-e820: [mem 0x0000000068c00000-0x0000000073007fff] usable
lug 03 14:26:45 lyoko kernel: BIOS-e820: [mem 0x0000000073008000-0x0000000074807fff] reserved
lug 03 14:26:45 lyoko kernel: BIOS-e820: [mem 0x0000000074808000-0x0000000074913fff] ACPI data
lug 03 14:26:45 lyoko kernel: BIOS-e820: [mem 0x0000000074914000-0x0000000074b13fff] ACPI NVS
lug 03 14:26:45 lyoko kernel: BIOS-e820: [mem 0x0000000074b14000-0x0000000079bfefff] reserved
lug 03 14:26:45 lyoko kernel: BIOS-e820: [mem 0x0000000079bff000-0x0000000079bfffff] usable
lug 03 14:26:45 lyoko kernel: BIOS-e820: [mem 0x0000000079c00000-0x000000007dffffff] reserved
lug 03 14:26:45 lyoko kernel: BIOS-e820: [mem 0x000000007ee00000-0x000000007fffffff] reserved
lug 03 14:26:45 lyoko kernel: BIOS-e820: [mem 0x00000000c0000000-0x00000000cfffffff] reserved
lug 03 14:26:45 lyoko kernel: BIOS-e820: [mem 0x00000000fe000000-0x00000000fe010fff] reserved
lug 03 14:26:45 lyoko kernel: BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
lug 03 14:26:45 lyoko kernel: BIOS-e820: [mem 0x00000000fed00000-0x00000000fed00fff] reserved
lug 03 14:26:45 lyoko kernel: BIOS-e820: [mem 0x00000000fed20000-0x00000000fed7ffff] reserved
lug 03 14:26:45 lyoko kernel: BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
lug 03 14:26:45 lyoko kernel: BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
lug 03 14:26:45 lyoko kernel: BIOS-e820: [mem 0x0000000100000000-0x000000047fffffff] usable
lug 03 14:26:45 lyoko kernel: NX (Execute Disable) protection: active
lug 03 14:26:45 lyoko kernel: APIC: Static calls initialized
lug 03 14:26:45 lyoko kernel: efi: EFI v2.9 by American Megatrends
lug 03 14:26:45 lyoko kernel: efi: ACPI=0x74ad0000 ACPI 2.0=0x74ad0014 TPMFinalLog=0x74a9f000 SMBIOS=0x76657000 SMBIOS 3.0=0x76656000 MEMATTR=0x6cd3c018 ESRT=0x6e5d0c18 INITRD=0x6b54ae98 RNG=0x7483c018 TPMEventLog=0x74833018
lug 03 14:26:45 lyoko kernel: random: crng init done
lug 03 14:26:45 lyoko kernel: efi: Remove mem74: MMIO range=[0xc0000000-0xcfffffff] (256MB) from e820 map
lug 03 14:26:45 lyoko kernel: e820: remove [mem 0xc0000000-0xcfffffff] reserved
lug 03 14:26:45 lyoko kernel: efi: Not removing mem75: MMIO range=[0xfe000000-0xfe010fff] (68KB) from e820 map
lug 03 14:26:45 lyoko kernel: efi: Not removing mem76: MMIO range=[0xfec00000-0xfec00fff] (4KB) from e820 map
lug 03 14:26:45 lyoko kernel: efi: Not removing mem77: MMIO range=[0xfed00000-0xfed00fff] (4KB) from e820 map
lug 03 14:26:45 lyoko kernel: efi: Not removing mem79: MMIO range=[0xfee00000-0xfee00fff] (4KB) from e820 map
lug 03 14:26:45 lyoko kernel: efi: Remove mem80: MMIO range=[0xff000000-0xffffffff] (16MB) from e820 map
lug 03 14:26:45 lyoko kernel: e820: remove [mem 0xff000000-0xffffffff] reserved
lug 03 14:26:45 lyoko kernel: SMBIOS 3.6.0 present.
lug 03 14:26:45 lyoko kernel: DMI: Micro-Star International Co., Ltd. MS-7D46/PRO H610M-B DDR4 (MS-7D46), BIOS 1.N1 05/13/2025
lug 03 14:26:45 lyoko kernel: DMI: Memory slots populated: 2/2
lug 03 14:26:45 lyoko kernel: tsc: Detected 3300.000 MHz processor
lug 03 14:26:45 lyoko kernel: tsc: Detected 3302.400 MHz TSC
lug 03 14:26:45 lyoko kernel: e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
lug 03 14:26:45 lyoko kernel: e820: remove [mem 0x000a0000-0x000fffff] usable
lug 03 14:26:45 lyoko kernel: last_pfn = 0x480000 max_arch_pfn = 0x400000000
lug 03 14:26:45 lyoko kernel: MTRR map: 5 entries (3 fixed + 2 variable; max 23), built from 10 variable MTRRs
lug 03 14:26:45 lyoko kernel: x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT
lug 03 14:26:45 lyoko kernel: last_pfn = 0x79c00 max_arch_pfn = 0x400000000
lug 03 14:26:45 lyoko kernel: esrt: Reserving ESRT space from 0x000000006e5d0c18 to 0x000000006e5d0cc8.
lug 03 14:26:45 lyoko kernel: e820: update [mem 0x6e5d0000-0x6e5d0fff] usable ==> reserved
lug 03 14:26:45 lyoko kernel: Using GB pages for direct mapping
lug 03 14:26:45 lyoko kernel: Secure boot disabled
lug 03 14:26:45 lyoko kernel: RAMDISK: [mem 0x5c4c7000-0x5f5cefff]
lug 03 14:26:45 lyoko kernel: ACPI: Early table checksum verification disabled
lug 03 14:26:45 lyoko kernel: ACPI: RSDP 0x0000000074AD0014 000024 (v02 ALASKA)
lug 03 14:26:45 lyoko kernel: ACPI: XSDT 0x0000000074ACF728 0000FC (v01 ALASKA A M I 01072009 AMI 01000013)
lug 03 14:26:45 lyoko kernel: ACPI: FACP 0x0000000074911000 000114 (v06 ALASKA A M I 01072009 AMI 01000013)
lug 03 14:26:45 lyoko kernel: ACPI: DSDT 0x0000000074872000 09EBD0 (v02 ALASKA A M I 01072009 INTL 20200717)
lug 03 14:26:45 lyoko kernel: ACPI: FACS 0x0000000074B13000 000040
lug 03 14:26:45 lyoko kernel: ACPI: FIDT 0x0000000074871000 00009C (v01 ALASKA A M I 01072009 AMI 00010013)
lug 03 14:26:45 lyoko kernel: ACPI: SSDT 0x0000000074913000 00038C (v02 PmaxDv Pmax_Dev 00000001 INTL 20200717)
lug 03 14:26:45 lyoko kernel: ACPI: SSDT 0x000000007486B000 005D34 (v02 CpuRef CpuSsdt 00003000 INTL 20200717)
lug 03 14:26:45 lyoko kernel: ACPI: SSDT 0x0000000074868000 002BA7 (v02 SaSsdt SaSsdt 00003000 INTL 20200717)
lug 03 14:26:45 lyoko kernel: ACPI: SSDT 0x0000000074864000 00334F (v02 INTEL IgfxSsdt 00003000 INTL 20200717)
lug 03 14:26:45 lyoko kernel: ACPI: HPET 0x0000000074912000 000038 (v01 ALASKA A M I 01072009 AMI 01000013)
lug 03 14:26:45 lyoko kernel: ACPI: APIC 0x0000000074863000 0001DC (v05 ALASKA A M I 01072009 AMI 01000013)
lug 03 14:26:45 lyoko kernel: ACPI: MCFG 0x0000000074862000 00003C (v01 ALASKA A M I 01072009 AMI 01000013)
lug 03 14:26:45 lyoko kernel: ACPI: SSDT 0x0000000074860000 001F1A (v02 ALASKA Ther_Rvp 00001000 INTL 20200717)
lug 03 14:26:45 lyoko kernel: ACPI: UEFI 0x0000000074A87000 000048 (v01 ALASKA A M I 01072009 AMI 01000013)
lug 03 14:26:45 lyoko kernel: ACPI: NHLT 0x000000007485F000 00002D (v00 ALASKA A M I 01072009 AMI 01000013)
lug 03 14:26:45 lyoko kernel: ACPI: LPIT 0x000000007485E000 0000CC (v01 ALASKA A M I 01072009 AMI 01000013)
lug 03 14:26:45 lyoko kernel: ACPI: SSDT 0x000000007485A000 002A83 (v02 ALASKA PtidDevc 00001000 INTL 20200717)
lug 03 14:26:45 lyoko kernel: ACPI: SSDT 0x0000000074850000 0093E7 (v02 ALASKA TbtTypeC 00000000 INTL 20200717)
lug 03 14:26:45 lyoko kernel: ACPI: DBGP 0x000000007484F000 000034 (v01 ALASKA A M I 01072009 AMI 01000013)
lug 03 14:26:45 lyoko kernel: ACPI: DBG2 0x000000007484E000 000054 (v00 ALASKA A M I 01072009 AMI 01000013)
lug 03 14:26:45 lyoko kernel: ACPI: SSDT 0x000000007484C000 00190A (v02 ALASKA UsbCTabl 00001000 INTL 20200717)
lug 03 14:26:45 lyoko kernel: ACPI: DMAR 0x000000007484B000 000050 (v01 INTEL EDK2 00000002 01000013)
lug 03 14:26:45 lyoko kernel: ACPI: FPDT 0x000000007484A000 000044 (v01 ALASKA A M I 01072009 AMI 01000013)
lug 03 14:26:45 lyoko kernel: ACPI: SSDT 0x0000000074848000 001621 (v02 INTEL xh_adls3 00000000 INTL 20200717)
lug 03 14:26:45 lyoko kernel: ACPI: SSDT 0x0000000074844000 0039DA (v02 SocGpe SocGpe 00003000 INTL 20200717)
lug 03 14:26:45 lyoko kernel: ACPI: SSDT 0x0000000074840000 0039DA (v02 SocCmn SocCmn 00003000 INTL 20200717)
lug 03 14:26:45 lyoko kernel: ACPI: PHAT 0x000000007483E000 00083C (v01 ALASKA A M I 00000005 MSFT 0100000D)
lug 03 14:26:45 lyoko kernel: ACPI: TPM2 0x000000007483D000 00004C (v04 ALASKA A M I 00000001 AMI 00000000)
lug 03 14:26:45 lyoko kernel: ACPI: WSMT 0x000000007485D000 000028 (v01 ALASKA A M I 01072009 AMI 00010013)
lug 03 14:26:45 lyoko kernel: ACPI: BGRT 0x000000007483F000 000038 (v01 ALASKA A M I 01072009 AMI 00010013)
lug 03 14:26:45 lyoko kernel: ACPI: Reserving FACP table memory at [mem 0x74911000-0x74911113]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving DSDT table memory at [mem 0x74872000-0x74910bcf]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving FACS table memory at [mem 0x74b13000-0x74b1303f]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving FIDT table memory at [mem 0x74871000-0x7487109b]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving SSDT table memory at [mem 0x74913000-0x7491338b]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving SSDT table memory at [mem 0x7486b000-0x74870d33]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving SSDT table memory at [mem 0x74868000-0x7486aba6]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving SSDT table memory at [mem 0x74864000-0x7486734e]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving HPET table memory at [mem 0x74912000-0x74912037]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving APIC table memory at [mem 0x74863000-0x748631db]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving MCFG table memory at [mem 0x74862000-0x7486203b]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving SSDT table memory at [mem 0x74860000-0x74861f19]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving UEFI table memory at [mem 0x74a87000-0x74a87047]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving NHLT table memory at [mem 0x7485f000-0x7485f02c]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving LPIT table memory at [mem 0x7485e000-0x7485e0cb]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving SSDT table memory at [mem 0x7485a000-0x7485ca82]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving SSDT table memory at [mem 0x74850000-0x748593e6]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving DBGP table memory at [mem 0x7484f000-0x7484f033]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving DBG2 table memory at [mem 0x7484e000-0x7484e053]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving SSDT table memory at [mem 0x7484c000-0x7484d909]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving DMAR table memory at [mem 0x7484b000-0x7484b04f]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving FPDT table memory at [mem 0x7484a000-0x7484a043]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving SSDT table memory at [mem 0x74848000-0x74849620]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving SSDT table memory at [mem 0x74844000-0x748479d9]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving SSDT table memory at [mem 0x74840000-0x748439d9]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving PHAT table memory at [mem 0x7483e000-0x7483e83b]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving TPM2 table memory at [mem 0x7483d000-0x7483d04b]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving WSMT table memory at [mem 0x7485d000-0x7485d027]
lug 03 14:26:45 lyoko kernel: ACPI: Reserving BGRT table memory at [mem 0x7483f000-0x7483f037]
lug 03 14:26:45 lyoko kernel: No NUMA configuration found
lug 03 14:26:45 lyoko kernel: Faking a node at [mem 0x0000000000000000-0x000000047fffffff]
lug 03 14:26:45 lyoko kernel: NODE_DATA(0) allocated [mem 0x47ffd5280-0x47fffffff]
lug 03 14:26:45 lyoko kernel: Zone ranges:
lug 03 14:26:45 lyoko kernel: DMA [mem 0x0000000000001000-0x0000000000ffffff]
lug 03 14:26:45 lyoko kernel: DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
lug 03 14:26:45 lyoko kernel: Normal [mem 0x0000000100000000-0x000000047fffffff]
lug 03 14:26:45 lyoko kernel: Device empty
lug 03 14:26:45 lyoko kernel: Movable zone start for each node
lug 03 14:26:45 lyoko kernel: Early memory node ranges
lug 03 14:26:45 lyoko kernel: node 0: [mem 0x0000000000001000-0x000000000009dfff]
lug 03 14:26:45 lyoko kernel: node 0: [mem 0x000000000009f000-0x000000000009ffff]
lug 03 14:26:45 lyoko kernel: node 0: [mem 0x0000000000100000-0x0000000067ffffff]
lug 03 14:26:45 lyoko kernel: node 0: [mem 0x0000000068c00000-0x0000000073007fff]
lug 03 14:26:45 lyoko kernel: node 0: [mem 0x0000000079bff000-0x0000000079bfffff]
lug 03 14:26:45 lyoko kernel: node 0: [mem 0x0000000100000000-0x000000047fffffff]
lug 03 14:26:45 lyoko kernel: Initmem setup node 0 [mem 0x0000000000001000-0x000000047fffffff]
lug 03 14:26:45 lyoko kernel: On node 0, zone DMA: 1 pages in unavailable ranges
lug 03 14:26:45 lyoko kernel: On node 0, zone DMA: 1 pages in unavailable ranges
lug 03 14:26:45 lyoko kernel: On node 0, zone DMA: 96 pages in unavailable ranges
lug 03 14:26:45 lyoko kernel: On node 0, zone DMA32: 3072 pages in unavailable ranges
lug 03 14:26:45 lyoko kernel: On node 0, zone DMA32: 27639 pages in unavailable ranges
lug 03 14:26:45 lyoko kernel: On node 0, zone Normal: 25600 pages in unavailable ranges
lug 03 14:26:45 lyoko kernel: ACPI: PM-Timer IO Port: 0x1808
lug 03 14:26:45 lyoko kernel: ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
lug 03 14:26:45 lyoko kernel: ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
lug 03 14:26:45 lyoko kernel: ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
lug 03 14:26:45 lyoko kernel: ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
lug 03 14:26:45 lyoko kernel: ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])
lug 03 14:26:45 lyoko kernel: ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
lug 03 14:26:45 lyoko kernel: ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
lug 03 14:26:45 lyoko kernel: ACPI: LAPIC_NMI (acpi_id[0x08] high edge lint[0x1])
lug 03 14:26:45 lyoko kernel: ACPI: LAPIC_NMI (acpi_id[0x09] high edge lint[0x1])
lug 03 14:26:45 lyoko kernel: ACPI: LAPIC_NMI (acpi_id[0x0a] high edge lint[0x1])
lug 03 14:26:45 lyoko kernel: ACPI: LAPIC_NMI (acpi_id[0x0b] high edge lint[0x1])
lug 03 14:26:45 lyoko kernel: ACPI: LAPIC_NMI (acpi_id[0x0c] high edge lint[0x1])
lug 03 14:26:45 lyoko kernel: ACPI: LAPIC_NMI (acpi_id[0x0d] high edge lint[0x1])
lug 03 14:26:45 lyoko kernel: ACPI: LAPIC_NMI (acpi_id[0x0e] high edge lint[0x1])
lug 03 14:26:45 lyoko kernel: ACPI: LAPIC_NMI (acpi_id[0x0f] high edge lint[0x1])
lug 03 14:26:45 lyoko kernel: ACPI: LAPIC_NMI (acpi_id[0x10] high edge lint[0x1])
lug 03 14:26:45 lyoko kernel: ACPI: LAPIC_NMI (acpi_id[0x11] high edge lint[0x1])
lug 03 14:26:45 lyoko kernel: ACPI: LAPIC_NMI (acpi_id[0x12] high edge lint[0x1])
lug 03 14:26:45 lyoko kernel: ACPI: LAPIC_NMI (acpi_id[0x13] high edge lint[0x1])
lug 03 14:26:45 lyoko kernel: ACPI: LAPIC_NMI (acpi_id[0x14] high edge lint[0x1])
lug 03 14:26:45 lyoko kernel: ACPI: LAPIC_NMI (acpi_id[0x15] high edge lint[0x1])
lug 03 14:26:45 lyoko kernel: ACPI: LAPIC_NMI (acpi_id[0x16] high edge lint[0x1])
lug 03 14:26:45 lyoko kernel: ACPI: LAPIC_NMI (acpi_id[0x17] high edge lint[0x1])
lug 03 14:26:45 lyoko kernel: ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
lug 03 14:26:45 lyoko kernel: IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-119
lug 03 14:26:45 lyoko kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
lug 03 14:26:45 lyoko kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
lug 03 14:26:45 lyoko kernel: ACPI: Using ACPI (MADT) for SMP configuration information
lug 03 14:26:45 lyoko kernel: ACPI: HPET id: 0x8086a201 base: 0xfed00000
lug 03 14:26:45 lyoko kernel: e820: update [mem 0x6cbff000-0x6cc5bfff] usable ==> reserved
lug 03 14:26:45 lyoko kernel: TSC deadline timer available
lug 03 14:26:45 lyoko kernel: CPU topo: Max. logical packages: 1
lug 03 14:26:45 lyoko kernel: CPU topo: Max. logical dies: 1
lug 03 14:26:45 lyoko kernel: CPU topo: Max. dies per package: 1
lug 03 14:26:45 lyoko kernel: CPU topo: Max. threads per core: 2
lug 03 14:26:45 lyoko kernel: CPU topo: Num. cores per package: 4
lug 03 14:26:45 lyoko kernel: CPU topo: Num. threads per package: 8
lug 03 14:26:45 lyoko kernel: CPU topo: Allowing 8 present CPUs plus 0 hotplug CPUs
lug 03 14:26:45 lyoko kernel: PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff]
lug 03 14:26:45 lyoko kernel: PM: hibernation: Registered nosave memory: [mem 0x0009e000-0x0009efff]
lug 03 14:26:45 lyoko kernel: PM: hibernation: Registered nosave memory: [mem 0x000a0000-0x000fffff]
lug 03 14:26:45 lyoko kernel: PM: hibernation: Registered nosave memory: [mem 0x68000000-0x68bfffff]
lug 03 14:26:45 lyoko kernel: PM: hibernation: Registered nosave memory: [mem 0x6cbff000-0x6cc5bfff]
lug 03 14:26:45 lyoko kernel: PM: hibernation: Registered nosave memory: [mem 0x6e5d0000-0x6e5d0fff]
lug 03 14:26:45 lyoko kernel: PM: hibernation: Registered nosave memory: [mem 0x73008000-0x79bfefff]
lug 03 14:26:45 lyoko kernel: PM: hibernation: Registered nosave memory: [mem 0x79c00000-0xffffffff]
lug 03 14:26:45 lyoko kernel: [mem 0x80000000-0xfdffffff] available for PCI devices
lug 03 14:26:45 lyoko kernel: Booting paravirtualized kernel on bare hardware
lug 03 14:26:45 lyoko kernel: clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns
lug 03 14:26:45 lyoko kernel: setup_percpu: NR_CPUS:8192 nr_cpumask_bits:8 nr_cpu_ids:8 nr_node_ids:1
lug 03 14:26:45 lyoko kernel: percpu: Embedded 62 pages/cpu s217088 r8192 d28672 u262144
lug 03 14:26:45 lyoko kernel: pcpu-alloc: s217088 r8192 d28672 u262144 alloc=1*2097152
lug 03 14:26:45 lyoko kernel: pcpu-alloc: [0] 0 1 2 3 4 5 6 7
lug 03 14:26:45 lyoko kernel: Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=1d61a5b2-8700-4954-8d30-c4288198c34c rw loglevel=3 quiet
lug 03 14:26:45 lyoko kernel: Unknown kernel command line parameters "BOOT_IMAGE=/boot/vmlinuz-linux", will be passed to user space.
lug 03 14:26:45 lyoko kernel: printk: log buffer data + meta data: 131072 + 458752 = 589824 bytes
lug 03 14:26:45 lyoko kernel: Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear)
lug 03 14:26:45 lyoko kernel: Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
lug 03 14:26:45 lyoko kernel: software IO TLB: area num 8.
lug 03 14:26:45 lyoko kernel: Fallback order for Node 0: 0
lug 03 14:26:45 lyoko kernel: Built 1 zonelists, mobility grouping on. Total pages: 4137895
lug 03 14:26:45 lyoko kernel: Policy zone: Normal
lug 03 14:26:45 lyoko kernel: mem auto-init: stack:all(zero), heap alloc:on, heap free:off
lug 03 14:26:45 lyoko kernel: SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
lug 03 14:26:45 lyoko kernel: ftrace: allocating 55579 entries in 220 pages
lug 03 14:26:45 lyoko kernel: ftrace: allocated 220 pages with 5 groups
lug 03 14:26:45 lyoko kernel: Dynamic Preempt: full
lug 03 14:26:45 lyoko kernel: rcu: Preemptible hierarchical RCU implementation.
lug 03 14:26:45 lyoko kernel: rcu: RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=8.
lug 03 14:26:45 lyoko kernel: rcu: RCU priority boosting: priority 1 delay 500 ms.
lug 03 14:26:45 lyoko kernel: Trampoline variant of Tasks RCU enabled.
lug 03 14:26:45 lyoko kernel: Rude variant of Tasks RCU enabled.
lug 03 14:26:45 lyoko kernel: Tracing variant of Tasks RCU enabled.
lug 03 14:26:45 lyoko kernel: rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies.
lug 03 14:26:45 lyoko kernel: rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
lug 03 14:26:45 lyoko kernel: RCU Tasks: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=8.
lug 03 14:26:45 lyoko kernel: RCU Tasks Rude: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=8.
lug 03 14:26:45 lyoko kernel: RCU Tasks Trace: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=8.
lug 03 14:26:45 lyoko kernel: NR_IRQS: 524544, nr_irqs: 2048, preallocated irqs: 16
lug 03 14:26:45 lyoko kernel: rcu: srcu_init: Setting srcu_struct sizes based on contention.
lug 03 14:26:45 lyoko kernel: kfence: initialized - using 2097152 bytes for 255 objects at 0x(____ptrval____)-0x(____ptrval____)
lug 03 14:26:45 lyoko kernel: Console: colour dummy device 80x25
lug 03 14:26:45 lyoko kernel: printk: legacy console [tty0] enabled
lug 03 14:26:45 lyoko kernel: ACPI: Core revision 20240827
lug 03 14:26:45 lyoko kernel: clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 99544814920 ns
lug 03 14:26:45 lyoko kernel: APIC: Switch to symmetric I/O mode setup
lug 03 14:26:45 lyoko kernel: DMAR: Host address width 39
lug 03 14:26:45 lyoko kernel: DMAR: DRHD base: 0x000000fed91000 flags: 0x1
lug 03 14:26:45 lyoko kernel: DMAR: dmar0: reg_base_addr fed91000 ver 5:0 cap d2008c40660462 ecap f050da
lug 03 14:26:45 lyoko kernel: DMAR-IR: IOAPIC id 2 under DRHD base 0xfed91000 IOMMU 0
lug 03 14:26:45 lyoko kernel: DMAR-IR: HPET id 0 under DRHD base 0xfed91000
lug 03 14:26:45 lyoko kernel: DMAR-IR: Queued invalidation will be enabled to support x2apic and Intr-remapping.
lug 03 14:26:45 lyoko kernel: DMAR-IR: Enabled IRQ remapping in x2apic mode
lug 03 14:26:45 lyoko kernel: x2apic enabled
lug 03 14:26:45 lyoko kernel: APIC: Switched APIC routing to: cluster x2apic
lug 03 14:26:45 lyoko kernel: ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
lug 03 14:26:45 lyoko kernel: clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x2f9a2767029, max_idle_ns: 440795219692 ns
lug 03 14:26:45 lyoko kernel: Calibrating delay loop (skipped), value calculated using timer frequency.. 6604.80 BogoMIPS (lpj=3302400)
lug 03 14:26:45 lyoko kernel: CPU0: Thermal monitoring enabled (TM1)
lug 03 14:26:45 lyoko kernel: x86/cpu: User Mode Instruction Prevention (UMIP) activated
lug 03 14:26:45 lyoko kernel: CET detected: Indirect Branch Tracking enabled
lug 03 14:26:45 lyoko kernel: Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
lug 03 14:26:45 lyoko kernel: Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0
lug 03 14:26:45 lyoko kernel: process: using mwait in idle threads
lug 03 14:26:45 lyoko kernel: Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
lug 03 14:26:45 lyoko kernel: Spectre V2 : Mitigation: Enhanced / Automatic IBRS
lug 03 14:26:45 lyoko kernel: Spectre V2 : Spectre v2 / PBRSB-eIBRS: Retire a single CALL on VMEXIT
lug 03 14:26:45 lyoko kernel: Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier
lug 03 14:26:45 lyoko kernel: Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl
lug 03 14:26:45 lyoko kernel: x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
lug 03 14:26:45 lyoko kernel: x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
lug 03 14:26:45 lyoko kernel: x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
lug 03 14:26:45 lyoko kernel: x86/fpu: Supporting XSAVE feature 0x200: 'Protection Keys User registers'
lug 03 14:26:45 lyoko kernel: x86/fpu: Supporting XSAVE feature 0x800: 'Control-flow User registers'
lug 03 14:26:45 lyoko kernel: x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256
lug 03 14:26:45 lyoko kernel: x86/fpu: xstate_offset[9]: 832, xstate_sizes[9]: 8
lug 03 14:26:45 lyoko kernel: x86/fpu: xstate_offset[11]: 840, xstate_sizes[11]: 16
lug 03 14:26:45 lyoko kernel: x86/fpu: Enabled xstate features 0xa07, context size is 856 bytes, using 'compacted' format.
lug 03 14:26:45 lyoko kernel: Freeing SMP alternatives memory: 52K
lug 03 14:26:45 lyoko kernel: pid_max: default: 32768 minimum: 301
lug 03 14:26:45 lyoko kernel: LSM: initializing lsm=capability,landlock,lockdown,yama,bpf
lug 03 14:26:45 lyoko kernel: landlock: Up and running.
lug 03 14:26:45 lyoko kernel: Yama: becoming mindful.
lug 03 14:26:45 lyoko kernel: LSM support for eBPF active
lug 03 14:26:45 lyoko kernel: Mount-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
lug 03 14:26:45 lyoko kernel: Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
lug 03 14:26:45 lyoko kernel: smpboot: CPU0: 12th Gen Intel(R) Core(TM) i3-12100F (family: 0x6, model: 0x97, stepping: 0x5)
lug 03 14:26:45 lyoko kernel: Performance Events: XSAVE Architectural LBR, PEBS fmt4+-baseline, AnyThread deprecated, Alderlake Hybrid events, 32-deep LBR, full-width counters, Intel PMU driver.
lug 03 14:26:45 lyoko kernel: core: cpu_core PMU driver:
lug 03 14:26:45 lyoko kernel: ... version: 5
lug 03 14:26:45 lyoko kernel: ... bit width: 48
lug 03 14:26:45 lyoko kernel: ... generic registers: 8
lug 03 14:26:45 lyoko kernel: ... value mask: 0000ffffffffffff
lug 03 14:26:45 lyoko kernel: ... max period: 00007fffffffffff
lug 03 14:26:45 lyoko kernel: ... fixed-purpose events: 4
lug 03 14:26:45 lyoko kernel: ... event mask: 0001000f000000ff
lug 03 14:26:45 lyoko kernel: signal: max sigframe size: 3632
lug 03 14:26:45 lyoko kernel: Estimated ratio of average max frequency by base frequency (times 1024): 1272
lug 03 14:26:45 lyoko kernel: rcu: Hierarchical SRCU implementation.
lug 03 14:26:45 lyoko kernel: rcu: Max phase no-delay instances is 400.
lug 03 14:26:45 lyoko kernel: Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level
lug 03 14:26:45 lyoko kernel: NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
lug 03 14:26:45 lyoko kernel: smp: Bringing up secondary CPUs ...
lug 03 14:26:45 lyoko kernel: smpboot: x86: Booting SMP configuration:
lug 03 14:26:45 lyoko kernel: .... node #0, CPUs: #2 #4 #6 #1 #3 #5 #7
lug 03 14:26:45 lyoko kernel: smp: Brought up 1 node, 8 CPUs
lug 03 14:26:45 lyoko kernel: smpboot: Total of 8 processors activated (52838.40 BogoMIPS)
lug 03 14:26:45 lyoko kernel: Memory: 16068020K/16551580K available (19692K kernel code, 2940K rwdata, 16520K rodata, 4632K init, 5036K bss, 466348K reserved, 0K cma-reserved)
lug 03 14:26:45 lyoko kernel: devtmpfs: initialized
lug 03 14:26:45 lyoko kernel: x86/mm: Memory block size: 128MB
lug 03 14:26:45 lyoko kernel: ACPI: PM: Registering ACPI NVS region [mem 0x74914000-0x74b13fff] (2097152 bytes)
lug 03 14:26:45 lyoko kernel: clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
lug 03 14:26:45 lyoko kernel: posixtimers hash table entries: 4096 (order: 4, 65536 bytes, linear)
lug 03 14:26:45 lyoko kernel: futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
lug 03 14:26:45 lyoko kernel: pinctrl core: initialized pinctrl subsystem
lug 03 14:26:45 lyoko kernel: PM: RTC time: 12:26:43, date: 2025-07-03
lug 03 14:26:45 lyoko kernel: NET: Registered PF_NETLINK/PF_ROUTE protocol family
lug 03 14:26:45 lyoko kernel: DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations
lug 03 14:26:45 lyoko kernel: DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
lug 03 14:26:45 lyoko kernel: DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
lug 03 14:26:45 lyoko kernel: audit: initializing netlink subsys (disabled)
lug 03 14:26:45 lyoko kernel: audit: type=2000 audit(1751545603.031:1): state=initialized audit_enabled=0 res=1
lug 03 14:26:45 lyoko kernel: thermal_sys: Registered thermal governor 'fair_share'
lug 03 14:26:45 lyoko kernel: thermal_sys: Registered thermal governor 'bang_bang'
lug 03 14:26:45 lyoko kernel: thermal_sys: Registered thermal governor 'step_wise'
lug 03 14:26:45 lyoko kernel: thermal_sys: Registered thermal governor 'user_space'
lug 03 14:26:45 lyoko kernel: thermal_sys: Registered thermal governor 'power_allocator'
lug 03 14:26:45 lyoko kernel: cpuidle: using governor ladder
lug 03 14:26:45 lyoko kernel: cpuidle: using governor menu
lug 03 14:26:45 lyoko kernel: ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
lug 03 14:26:45 lyoko kernel: acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
lug 03 14:26:45 lyoko kernel: PCI: ECAM [mem 0xc0000000-0xcfffffff] (base 0xc0000000) for domain 0000 [bus 00-ff]
lug 03 14:26:45 lyoko kernel: PCI: Using configuration type 1 for base access
lug 03 14:26:45 lyoko kernel: kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible.
lug 03 14:26:45 lyoko kernel: HugeTLB: allocation took 0ms with hugepage_allocation_threads=2
lug 03 14:26:45 lyoko kernel: HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages
lug 03 14:26:45 lyoko kernel: HugeTLB: 16380 KiB vmemmap can be freed for a 1.00 GiB page
lug 03 14:26:45 lyoko kernel: HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages
lug 03 14:26:45 lyoko kernel: HugeTLB: 28 KiB vmemmap can be freed for a 2.00 MiB page
lug 03 14:26:45 lyoko kernel: raid6: skipped pq benchmark and selected avx2x4
lug 03 14:26:45 lyoko kernel: raid6: using avx2x2 recovery algorithm
lug 03 14:26:45 lyoko kernel: ACPI: Added _OSI(Module Device)
lug 03 14:26:45 lyoko kernel: ACPI: Added _OSI(Processor Device)
lug 03 14:26:45 lyoko kernel: ACPI: Added _OSI(Processor Aggregator Device)
lug 03 14:26:45 lyoko kernel: ACPI: 12 ACPI AML tables successfully acquired and loaded
lug 03 14:26:45 lyoko kernel: ACPI: Dynamic OEM Table Load:
lug 03 14:26:45 lyoko kernel: ACPI: SSDT 0xFFFF8C5E4189A800 000394 (v02 PmRef Cpu0Cst 00003001 INTL 20200717)
lug 03 14:26:45 lyoko kernel: ACPI: Dynamic OEM Table Load:
lug 03 14:26:45 lyoko kernel: ACPI: SSDT 0xFFFF8C5E418A5000 000668 (v02 PmRef Cpu0Ist 00003000 INTL 20200717)
lug 03 14:26:45 lyoko kernel: ACPI: Dynamic OEM Table Load:
lug 03 14:26:45 lyoko kernel: ACPI: SSDT 0xFFFF8C5E4083C000 0001AB (v02 PmRef Cpu0Psd 00003000 INTL 20200717)
lug 03 14:26:45 lyoko kernel: ACPI: Dynamic OEM Table Load:
lug 03 14:26:45 lyoko kernel: ACPI: SSDT 0xFFFF8C5E418A7800 0004B5 (v02 PmRef Cpu0Hwp 00003000 INTL 20200717)
lug 03 14:26:45 lyoko kernel: ACPI: Dynamic OEM Table Load:
lug 03 14:26:45 lyoko kernel: ACPI: SSDT 0xFFFF8C5E418AC000 001BAF (v02 PmRef ApIst 00003000 INTL 20200717)
lug 03 14:26:45 lyoko kernel: ACPI: Dynamic OEM Table Load:
lug 03 14:26:45 lyoko kernel: ACPI: SSDT 0xFFFF8C5E418AE000 001038 (v02 PmRef ApHwp 00003000 INTL 20200717)
lug 03 14:26:45 lyoko kernel: ACPI: Dynamic OEM Table Load:
lug 03 14:26:45 lyoko kernel: ACPI: SSDT 0xFFFF8C5E418A8000 001349 (v02 PmRef ApPsd 00003000 INTL 20200717)
lug 03 14:26:45 lyoko kernel: ACPI: Dynamic OEM Table Load:
lug 03 14:26:45 lyoko kernel: ACPI: SSDT 0xFFFF8C5E401C4000 000FBB (v02 PmRef ApCst 00003000 INTL 20200717)
lug 03 14:26:45 lyoko kernel: ACPI: Interpreter enabled
lug 03 14:26:45 lyoko kernel: ACPI: PM: (supports S0 S3 S4 S5)
lug 03 14:26:45 lyoko kernel: ACPI: Using IOAPIC for interrupt routing
lug 03 14:26:45 lyoko kernel: PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
lug 03 14:26:45 lyoko kernel: PCI: Ignoring E820 reservations for host bridge windows
lug 03 14:26:45 lyoko kernel: ACPI: Enabled 6 GPEs in block 00 to 7F
lug 03 14:26:45 lyoko kernel: ACPI: \_SB_.PC00.CNVW.WRST: New power resource
lug 03 14:26:45 lyoko kernel: ACPI: \_TZ_.FN00: New power resource
lug 03 14:26:45 lyoko kernel: ACPI: \_TZ_.FN01: New power resource
lug 03 14:26:45 lyoko kernel: ACPI: \_TZ_.FN02: New power resource
lug 03 14:26:45 lyoko kernel: ACPI: \_TZ_.FN03: New power resource
lug 03 14:26:45 lyoko kernel: ACPI: \_TZ_.FN04: New power resource
lug 03 14:26:45 lyoko kernel: ACPI: \PIN_: New power resource
lug 03 14:26:45 lyoko kernel: ACPI: PCI Root Bridge [PC00] (domain 0000 [bus 00-fe])
lug 03 14:26:45 lyoko kernel: acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI EDR HPX-Type3]
lug 03 14:26:45 lyoko kernel: acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug SHPCHotplug PME AER PCIeCapability LTR DPC]
lug 03 14:26:45 lyoko kernel: acpi PNP0A08:00: FADT indicates ASPM is unsupported, using BIOS configuration
lug 03 14:26:45 lyoko kernel: PCI host bridge to bus 0000:00
lug 03 14:26:45 lyoko kernel: pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window]
lug 03 14:26:45 lyoko kernel: pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
lug 03 14:26:45 lyoko kernel: pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
lug 03 14:26:45 lyoko kernel: pci_bus 0000:00: root bus resource [mem 0x80000000-0xbfffffff window]
lug 03 14:26:45 lyoko kernel: pci_bus 0000:00: root bus resource [mem 0x4000000000-0x7fffffffff window]
lug 03 14:26:45 lyoko kernel: pci_bus 0000:00: root bus resource [bus 00-fe]
lug 03 14:26:45 lyoko kernel: pci 0000:00:00.0: [8086:4630] type 00 class 0x060000 conventional PCI endpoint
lug 03 14:26:45 lyoko kernel: pci 0000:00:01.0: [8086:460d] type 01 class 0x060400 PCIe Root Port
lug 03 14:26:45 lyoko kernel: pci 0000:00:01.0: PCI bridge to [bus 01]
lug 03 14:26:45 lyoko kernel: pci 0000:00:01.0: bridge window [io 0x3000-0x3fff]
lug 03 14:26:45 lyoko kernel: pci 0000:00:01.0: bridge window [mem 0x80000000-0x810fffff]
lug 03 14:26:45 lyoko kernel: pci 0000:00:01.0: bridge window [mem 0x4000000000-0x40120fffff 64bit pref]
lug 03 14:26:45 lyoko kernel: pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
lug 03 14:26:45 lyoko kernel: pci 0000:00:01.0: PTM enabled (root), 4ns granularity
lug 03 14:26:45 lyoko kernel: pci 0000:00:08.0: [8086:464f] type 00 class 0x088000 conventional PCI endpoint
lug 03 14:26:45 lyoko kernel: pci 0000:00:08.0: BAR 0 [mem 0x401222b000-0x401222bfff 64bit]
lug 03 14:26:45 lyoko kernel: pci 0000:00:0a.0: [8086:467d] type 00 class 0x118000 PCIe Root Complex Integrated Endpoint
lug 03 14:26:45 lyoko kernel: pci 0000:00:0a.0: BAR 0 [mem 0x4012210000-0x4012217fff 64bit]
lug 03 14:26:45 lyoko kernel: pci 0000:00:0a.0: enabling Extended Tags
lug 03 14:26:45 lyoko kernel: pci 0000:00:14.0: [8086:7ae0] type 00 class 0x0c0330 conventional PCI endpoint
lug 03 14:26:45 lyoko kernel: pci 0000:00:14.0: BAR 0 [mem 0x4012200000-0x401220ffff 64bit]
lug 03 14:26:45 lyoko kernel: pci 0000:00:14.0: PME# supported from D3hot D3cold
lug 03 14:26:45 lyoko kernel: pci 0000:00:14.2: [8086:7aa7] type 00 class 0x050000 conventional PCI endpoint
lug 03 14:26:45 lyoko kernel: pci 0000:00:14.2: BAR 0 [mem 0x4012224000-0x4012227fff 64bit]
lug 03 14:26:45 lyoko kernel: pci 0000:00:14.2: BAR 2 [mem 0x401222a000-0x401222afff 64bit]
lug 03 14:26:45 lyoko kernel: pci 0000:00:16.0: [8086:7ae8] type 00 class 0x078000 conventional PCI endpoint
lug 03 14:26:45 lyoko kernel: pci 0000:00:16.0: BAR 0 [mem 0x4012229000-0x4012229fff 64bit]
lug 03 14:26:45 lyoko kernel: pci 0000:00:16.0: PME# supported from D3hot
lug 03 14:26:45 lyoko kernel: pci 0000:00:17.0: [8086:7ae2] type 00 class 0x010601 conventional PCI endpoint
lug 03 14:26:45 lyoko kernel: pci 0000:00:17.0: BAR 0 [mem 0x81220000-0x81221fff]
lug 03 14:26:45 lyoko kernel: pci 0000:00:17.0: BAR 1 [mem 0x81223000-0x812230ff]
lug 03 14:26:45 lyoko kernel: pci 0000:00:17.0: BAR 2 [io 0x4050-0x4057]
lug 03 14:26:45 lyoko kernel: pci 0000:00:17.0: BAR 3 [io 0x4040-0x4043]
lug 03 14:26:45 lyoko kernel: pci 0000:00:17.0: BAR 4 [io 0x4020-0x403f]
lug 03 14:26:45 lyoko kernel: pci 0000:00:17.0: BAR 5 [mem 0x81222000-0x812227ff]
lug 03 14:26:45 lyoko kernel: pci 0000:00:17.0: PME# supported from D3hot
lug 03 14:26:45 lyoko kernel: pci 0000:00:1c.0: [8086:7ab8] type 01 class 0x060400 PCIe Root Port
lug 03 14:26:45 lyoko kernel: pci 0000:00:1c.0: PCI bridge to [bus 02]
lug 03 14:26:45 lyoko kernel: pci 0000:00:1c.0: bridge window [mem 0x81100000-0x811fffff]
lug 03 14:26:45 lyoko kernel: pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
lug 03 14:26:45 lyoko kernel: pci 0000:00:1c.0: PTM enabled (root), 4ns granularity
lug 03 14:26:45 lyoko kernel: pci 0000:00:1f.0: [8086:7a87] type 00 class 0x060100 conventional PCI endpoint
lug 03 14:26:45 lyoko kernel: pci 0000:00:1f.3: [8086:7ad0] type 00 class 0x040300 conventional PCI endpoint
lug 03 14:26:45 lyoko kernel: pci 0000:00:1f.3: BAR 0 [mem 0x4012220000-0x4012223fff 64bit]
lug 03 14:26:45 lyoko kernel: pci 0000:00:1f.3: BAR 4 [mem 0x4012100000-0x40121fffff 64bit]
lug 03 14:26:45 lyoko kernel: pci 0000:00:1f.3: PME# supported from D3hot D3cold
lug 03 14:26:45 lyoko kernel: pci 0000:00:1f.4: [8086:7aa3] type 00 class 0x0c0500 conventional PCI endpoint
lug 03 14:26:45 lyoko kernel: pci 0000:00:1f.4: BAR 0 [mem 0x4012228000-0x40122280ff 64bit]
lug 03 14:26:45 lyoko kernel: pci 0000:00:1f.4: BAR 4 [io 0xefa0-0xefbf]
lug 03 14:26:45 lyoko kernel: pci 0000:00:1f.5: [8086:7aa4] type 00 class 0x0c8000 conventional PCI endpoint
lug 03 14:26:45 lyoko kernel: pci 0000:00:1f.5: BAR 0 [mem 0xfe010000-0xfe010fff]
lug 03 14:26:45 lyoko kernel: pci 0000:00:1f.6: [8086:1a1d] type 00 class 0x020000 conventional PCI endpoint
lug 03 14:26:45 lyoko kernel: pci 0000:00:1f.6: BAR 0 [mem 0x81200000-0x8121ffff]
lug 03 14:26:45 lyoko kernel: pci 0000:00:1f.6: PME# supported from D0 D3hot D3cold
lug 03 14:26:45 lyoko kernel: pci 0000:01:00.0: [10de:1f08] type 00 class 0x030000 PCIe Legacy Endpoint
lug 03 14:26:45 lyoko kernel: pci 0000:01:00.0: BAR 0 [mem 0x80000000-0x80ffffff]
lug 03 14:26:45 lyoko kernel: pci 0000:01:00.0: BAR 1 [mem 0x4000000000-0x400fffffff 64bit pref]
lug 03 14:26:45 lyoko kernel: pci 0000:01:00.0: BAR 3 [mem 0x4010000000-0x4011ffffff 64bit pref]
lug 03 14:26:45 lyoko kernel: pci 0000:01:00.0: BAR 5 [io 0x3000-0x307f]
lug 03 14:26:45 lyoko kernel: pci 0000:01:00.0: ROM [mem 0x81000000-0x8107ffff pref]
lug 03 14:26:45 lyoko kernel: pci 0000:01:00.0: PME# supported from D0 D3hot
lug 03 14:26:45 lyoko kernel: pci 0000:01:00.0: 32.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x16 link at 0000:00:01.0 (capable of 126.016 Gb/s with 8.0 GT/s PCIe x16 link)
lug 03 14:26:45 lyoko kernel: pci 0000:01:00.1: [10de:10f9] type 00 class 0x040300 PCIe Endpoint
lug 03 14:26:45 lyoko kernel: pci 0000:01:00.1: BAR 0 [mem 0x81080000-0x81083fff]
lug 03 14:26:45 lyoko kernel: pci 0000:01:00.2: [10de:1ada] type 00 class 0x0c0330 PCIe Endpoint
lug 03 14:26:45 lyoko kernel: pci 0000:01:00.2: BAR 0 [mem 0x4012000000-0x401203ffff 64bit pref]
lug 03 14:26:45 lyoko kernel: pci 0000:01:00.2: BAR 3 [mem 0x4012040000-0x401204ffff 64bit pref]
lug 03 14:26:45 lyoko kernel: pci 0000:01:00.2: PME# supported from D0 D3hot
lug 03 14:26:45 lyoko kernel: pci 0000:01:00.3: [10de:1adb] type 00 class 0x0c8000 PCIe Endpoint
lug 03 14:26:45 lyoko kernel: pci 0000:01:00.3: BAR 0 [mem 0x81084000-0x81084fff]
lug 03 14:26:45 lyoko kernel: pci 0000:01:00.3: PME# supported from D0 D3hot
lug 03 14:26:45 lyoko kernel: pci 0000:00:01.0: PCI bridge to [bus 01]
lug 03 14:26:45 lyoko kernel: pci 0000:02:00.0: [2646:5017] type 00 class 0x010802 PCIe Endpoint
lug 03 14:26:45 lyoko kernel: pci 0000:02:00.0: BAR 0 [mem 0x81100000-0x81103fff 64bit]
lug 03 14:26:45 lyoko kernel: pci 0000:02:00.0: 31.504 Gb/s available PCIe bandwidth, limited by 8.0 GT/s PCIe x4 link at 0000:00:1c.0 (capable of 63.012 Gb/s with 16.0 GT/s PCIe x4 link)
lug 03 14:26:45 lyoko kernel: pci 0000:00:1c.0: PCI bridge to [bus 02]
lug 03 14:26:45 lyoko kernel: ACPI: PCI: Interrupt link LNKA configured for IRQ 0
lug 03 14:26:45 lyoko kernel: ACPI: PCI: Interrupt link LNKB configured for IRQ 1
lug 03 14:26:45 lyoko kernel: ACPI: PCI: Interrupt link LNKC configured for IRQ 0
lug 03 14:26:45 lyoko kernel: ACPI: PCI: Interrupt link LNKD configured for IRQ 0
lug 03 14:26:45 lyoko kernel: ACPI: PCI: Interrupt link LNKE configured for IRQ 0
lug 03 14:26:45 lyoko kernel: ACPI: PCI: Interrupt link LNKF configured for IRQ 0
lug 03 14:26:45 lyoko kernel: ACPI: PCI: Interrupt link LNKG configured for IRQ 0
lug 03 14:26:45 lyoko kernel: ACPI: PCI: Interrupt link LNKH configured for IRQ 0
lug 03 14:26:45 lyoko kernel: iommu: Default domain type: Translated
lug 03 14:26:45 lyoko kernel: iommu: DMA domain TLB invalidation policy: lazy mode
lug 03 14:26:45 lyoko kernel: SCSI subsystem initialized
lug 03 14:26:45 lyoko kernel: libata version 3.00 loaded.
lug 03 14:26:45 lyoko kernel: ACPI: bus type USB registered
lug 03 14:26:45 lyoko kernel: usbcore: registered new interface driver usbfs
lug 03 14:26:45 lyoko kernel: usbcore: registered new interface driver hub
lug 03 14:26:45 lyoko kernel: usbcore: registered new device driver usb
lug 03 14:26:45 lyoko kernel: EDAC MC: Ver: 3.0.0
lug 03 14:26:45 lyoko kernel: efivars: Registered efivars operations
lug 03 14:26:45 lyoko kernel: NetLabel: Initializing
lug 03 14:26:45 lyoko kernel: NetLabel: domain hash size = 128
lug 03 14:26:45 lyoko kernel: NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
lug 03 14:26:45 lyoko kernel: NetLabel: unlabeled traffic allowed by default
lug 03 14:26:45 lyoko kernel: mctp: management component transport protocol core
lug 03 14:26:45 lyoko kernel: NET: Registered PF_MCTP protocol family
lug 03 14:26:45 lyoko kernel: PCI: Using ACPI for IRQ routing
lug 03 14:26:45 lyoko kernel: PCI: pci_cache_line_size set to 64 bytes
lug 03 14:26:45 lyoko kernel: pci 0000:00:1f.5: BAR 0 [mem 0xfe010000-0xfe010fff]: can't claim; no compatible bridge window
lug 03 14:26:45 lyoko kernel: e820: reserve RAM buffer [mem 0x0009e000-0x0009ffff]
lug 03 14:26:45 lyoko kernel: e820: reserve RAM buffer [mem 0x6cbff000-0x6fffffff]
lug 03 14:26:45 lyoko kernel: e820: reserve RAM buffer [mem 0x6e5d0000-0x6fffffff]
lug 03 14:26:45 lyoko kernel: e820: reserve RAM buffer [mem 0x73008000-0x73ffffff]
lug 03 14:26:45 lyoko kernel: e820: reserve RAM buffer [mem 0x79c00000-0x7bffffff]
lug 03 14:26:45 lyoko kernel: pci 0000:01:00.0: vgaarb: setting as boot VGA device
lug 03 14:26:45 lyoko kernel: pci 0000:01:00.0: vgaarb: bridge control possible
lug 03 14:26:45 lyoko kernel: pci 0000:01:00.0: vgaarb: VGA device added: decodes=io+mem,owns=none,locks=none
lug 03 14:26:45 lyoko kernel: vgaarb: loaded
lug 03 14:26:45 lyoko kernel: hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
lug 03 14:26:45 lyoko kernel: hpet0: 8 comparators, 64-bit 19.200000 MHz counter
lug 03 14:26:45 lyoko kernel: clocksource: Switched to clocksource tsc-early
lug 03 14:26:45 lyoko kernel: VFS: Disk quotas dquot_6.6.0
lug 03 14:26:45 lyoko kernel: VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
lug 03 14:26:45 lyoko kernel: pnp: PnP ACPI init
lug 03 14:26:45 lyoko kernel: system 00:00: [io 0x0a00-0x0a0f] has been reserved
lug 03 14:26:45 lyoko kernel: system 00:00: [io 0x0a10-0x0a1f] has been reserved
lug 03 14:26:45 lyoko kernel: system 00:00: [io 0x0a20-0x0a2f] has been reserved
lug 03 14:26:45 lyoko kernel: pnp 00:01: [dma 0 disabled]
lug 03 14:26:45 lyoko kernel: system 00:02: [io 0x0680-0x069f] has been reserved
lug 03 14:26:45 lyoko kernel: system 00:02: [io 0x164e-0x164f] has been reserved
lug 03 14:26:45 lyoko kernel: system 00:03: [mem 0xfedc0000-0xfedc7fff] has been reserved
lug 03 14:26:45 lyoko kernel: system 00:03: [mem 0xfeda0000-0xfeda0fff] has been reserved
lug 03 14:26:45 lyoko kernel: system 00:03: [mem 0xfeda1000-0xfeda1fff] has been reserved
lug 03 14:26:45 lyoko kernel: system 00:03: [mem 0xc0000000-0xcfffffff] has been reserved
lug 03 14:26:45 lyoko kernel: system 00:03: [mem 0xfed20000-0xfed7ffff] could not be reserved
lug 03 14:26:45 lyoko kernel: system 00:03: [mem 0xfed90000-0xfed93fff] could not be reserved
lug 03 14:26:45 lyoko kernel: system 00:03: [mem 0xfed45000-0xfed8ffff] could not be reserved
lug 03 14:26:45 lyoko kernel: system 00:03: [mem 0xfee00000-0xfeefffff] could not be reserved
lug 03 14:26:45 lyoko kernel: system 00:04: [io 0x2000-0x20fe] has been reserved
lug 03 14:26:45 lyoko kernel: pnp: PnP ACPI: found 6 devices
lug 03 14:26:45 lyoko kernel: clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
lug 03 14:26:45 lyoko kernel: NET: Registered PF_INET protocol family
lug 03 14:26:45 lyoko kernel: IP idents hash table entries: 262144 (order: 9, 2097152 bytes, linear)
lug 03 14:26:45 lyoko kernel: tcp_listen_portaddr_hash hash table entries: 8192 (order: 5, 131072 bytes, linear)
lug 03 14:26:45 lyoko kernel: Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
lug 03 14:26:45 lyoko kernel: TCP established hash table entries: 131072 (order: 8, 1048576 bytes, linear)
lug 03 14:26:45 lyoko kernel: TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear)
lug 03 14:26:45 lyoko kernel: TCP: Hash tables configured (established 131072 bind 65536)
lug 03 14:26:45 lyoko kernel: MPTCP token hash table entries: 16384 (order: 6, 393216 bytes, linear)
lug 03 14:26:45 lyoko kernel: UDP hash table entries: 8192 (order: 7, 524288 bytes, linear)
lug 03 14:26:45 lyoko kernel: UDP-Lite hash table entries: 8192 (order: 7, 524288 bytes, linear)
lug 03 14:26:45 lyoko kernel: NET: Registered PF_UNIX/PF_LOCAL protocol family
lug 03 14:26:45 lyoko kernel: NET: Registered PF_XDP protocol family
lug 03 14:26:45 lyoko kernel: pci 0000:00:1f.5: BAR 0 [mem 0x81224000-0x81224fff]: assigned
lug 03 14:26:45 lyoko kernel: pci 0000:00:01.0: PCI bridge to [bus 01]
lug 03 14:26:45 lyoko kernel: pci 0000:00:01.0: bridge window [io 0x3000-0x3fff]
lug 03 14:26:45 lyoko kernel: pci 0000:00:01.0: bridge window [mem 0x80000000-0x810fffff]
lug 03 14:26:45 lyoko kernel: pci 0000:00:01.0: bridge window [mem 0x4000000000-0x40120fffff 64bit pref]
lug 03 14:26:45 lyoko kernel: pci 0000:00:1c.0: PCI bridge to [bus 02]
lug 03 14:26:45 lyoko kernel: pci 0000:00:1c.0: bridge window [mem 0x81100000-0x811fffff]
lug 03 14:26:45 lyoko kernel: pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window]
lug 03 14:26:45 lyoko kernel: pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window]
lug 03 14:26:45 lyoko kernel: pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
lug 03 14:26:45 lyoko kernel: pci_bus 0000:00: resource 7 [mem 0x80000000-0xbfffffff window]
lug 03 14:26:45 lyoko kernel: pci_bus 0000:00: resource 8 [mem 0x4000000000-0x7fffffffff window]
lug 03 14:26:45 lyoko kernel: pci_bus 0000:01: resource 0 [io 0x3000-0x3fff]
lug 03 14:26:45 lyoko kernel: pci_bus 0000:01: resource 1 [mem 0x80000000-0x810fffff]
lug 03 14:26:45 lyoko kernel: pci_bus 0000:01: resource 2 [mem 0x4000000000-0x40120fffff 64bit pref]
lug 03 14:26:45 lyoko kernel: pci_bus 0000:02: resource 1 [mem 0x81100000-0x811fffff]
lug 03 14:26:45 lyoko kernel: pci 0000:01:00.1: extending delay after power-on from D3hot to 20 msec
lug 03 14:26:45 lyoko kernel: pci 0000:01:00.1: D0 power state depends on 0000:01:00.0
lug 03 14:26:45 lyoko kernel: pci 0000:01:00.2: D0 power state depends on 0000:01:00.0
lug 03 14:26:45 lyoko kernel: pci 0000:01:00.3: D0 power state depends on 0000:01:00.0
lug 03 14:26:45 lyoko kernel: PCI: CLS 64 bytes, default 64
lug 03 14:26:45 lyoko kernel: PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
lug 03 14:26:45 lyoko kernel: software IO TLB: mapped [mem 0x00000000584c7000-0x000000005c4c7000] (64MB)
lug 03 14:26:45 lyoko kernel: clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2f9a2767029, max_idle_ns: 440795219692 ns
lug 03 14:26:45 lyoko kernel: clocksource: Switched to clocksource tsc
lug 03 14:26:45 lyoko kernel: platform rtc_cmos: registered platform RTC device (no PNP device found)
lug 03 14:26:45 lyoko kernel: Trying to unpack rootfs image as initramfs...
lug 03 14:26:45 lyoko kernel: Initialise system trusted keyrings
lug 03 14:26:45 lyoko kernel: Key type blacklist registered
lug 03 14:26:45 lyoko kernel: workingset: timestamp_bits=36 max_order=22 bucket_order=0
lug 03 14:26:45 lyoko kernel: fuse: init (API version 7.43)
lug 03 14:26:45 lyoko kernel: integrity: Platform Keyring initialized
lug 03 14:26:45 lyoko kernel: integrity: Machine keyring initialized
lug 03 14:26:45 lyoko kernel: xor: automatically using best checksumming function avx
lug 03 14:26:45 lyoko kernel: Key type asymmetric registered
lug 03 14:26:45 lyoko kernel: Asymmetric key parser 'x509' registered
lug 03 14:26:45 lyoko kernel: Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
lug 03 14:26:45 lyoko kernel: io scheduler mq-deadline registered
lug 03 14:26:45 lyoko kernel: io scheduler kyber registered
lug 03 14:26:45 lyoko kernel: io scheduler bfq registered
lug 03 14:26:45 lyoko kernel: ledtrig-cpu: registered to indicate activity on CPUs
lug 03 14:26:45 lyoko kernel: pcieport 0000:00:01.0: PME: Signaling with IRQ 120
lug 03 14:26:45 lyoko kernel: pcieport 0000:00:1c.0: PME: Signaling with IRQ 121
lug 03 14:26:45 lyoko kernel: input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
lug 03 14:26:45 lyoko kernel: ACPI: button: Sleep Button [SLPB]
lug 03 14:26:45 lyoko kernel: input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
lug 03 14:26:45 lyoko kernel: ACPI: button: Power Button [PWRB]
lug 03 14:26:45 lyoko kernel: input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
lug 03 14:26:45 lyoko kernel: ACPI: button: Power Button [PWRF]
lug 03 14:26:45 lyoko kernel: thermal LNXTHERM:00: registered as thermal_zone0
lug 03 14:26:45 lyoko kernel: ACPI: thermal: Thermal Zone [TZ00] (28 C)
lug 03 14:26:45 lyoko kernel: Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
lug 03 14:26:45 lyoko kernel: 00:01: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
lug 03 14:26:45 lyoko kernel: Non-volatile memory driver v1.3
lug 03 14:26:45 lyoko kernel: Linux agpgart interface v0.103
lug 03 14:26:45 lyoko kernel: Freeing initrd memory: 50208K
lug 03 14:26:45 lyoko kernel: ACPI: bus type drm_connector registered
lug 03 14:26:45 lyoko kernel: ahci 0000:00:17.0: version 3.0
lug 03 14:26:45 lyoko kernel: ahci 0000:00:17.0: AHCI vers 0001.0301, 32 command slots, 6 Gbps, SATA mode
lug 03 14:26:45 lyoko kernel: ahci 0000:00:17.0: 4/4 ports implemented (port mask 0xf0)
lug 03 14:26:45 lyoko kernel: ahci 0000:00:17.0: flags: 64bit ncq sntf led clo only pio slum part ems deso sadm sds
lug 03 14:26:45 lyoko kernel: scsi host0: ahci
lug 03 14:26:45 lyoko kernel: scsi host1: ahci
lug 03 14:26:45 lyoko kernel: scsi host2: ahci
lug 03 14:26:45 lyoko kernel: scsi host3: ahci
lug 03 14:26:45 lyoko kernel: scsi host4: ahci
lug 03 14:26:45 lyoko kernel: scsi host5: ahci
lug 03 14:26:45 lyoko kernel: scsi host6: ahci
lug 03 14:26:45 lyoko kernel: scsi host7: ahci
lug 03 14:26:45 lyoko kernel: ata1: DUMMY
lug 03 14:26:45 lyoko kernel: ata2: DUMMY
lug 03 14:26:45 lyoko kernel: ata3: DUMMY
lug 03 14:26:45 lyoko kernel: ata4: DUMMY
lug 03 14:26:45 lyoko kernel: ata5: SATA max UDMA/133 abar m2048@0x81222000 port 0x81222300 irq 122 lpm-pol 3
lug 03 14:26:45 lyoko kernel: ata6: SATA max UDMA/133 abar m2048@0x81222000 port 0x81222380 irq 122 lpm-pol 3
lug 03 14:26:45 lyoko kernel: ata7: SATA max UDMA/133 abar m2048@0x81222000 port 0x81222400 irq 122 lpm-pol 3
lug 03 14:26:45 lyoko kernel: ata8: SATA max UDMA/133 abar m2048@0x81222000 port 0x81222480 irq 122 lpm-pol 3
lug 03 14:26:45 lyoko kernel: xhci_hcd 0000:00:14.0: xHCI Host Controller
lug 03 14:26:45 lyoko kernel: xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
lug 03 14:26:45 lyoko kernel: xhci_hcd 0000:00:14.0: hcc params 0x20007fc1 hci version 0x120 quirks 0x0000000200009810
lug 03 14:26:45 lyoko kernel: xhci_hcd 0000:00:14.0: xHCI Host Controller
lug 03 14:26:45 lyoko kernel: xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
lug 03 14:26:45 lyoko kernel: xhci_hcd 0000:00:14.0: Host supports USB 3.2 Enhanced SuperSpeed
lug 03 14:26:45 lyoko kernel: usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.15
lug 03 14:26:45 lyoko kernel: usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
lug 03 14:26:45 lyoko kernel: usb usb1: Product: xHCI Host Controller
lug 03 14:26:45 lyoko kernel: usb usb1: Manufacturer: Linux 6.15.4-arch2-1 xhci-hcd
lug 03 14:26:45 lyoko kernel: usb usb1: SerialNumber: 0000:00:14.0
lug 03 14:26:45 lyoko kernel: hub 1-0:1.0: USB hub found
lug 03 14:26:45 lyoko kernel: hub 1-0:1.0: 16 ports detected
lug 03 14:26:45 lyoko kernel: usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.15
lug 03 14:26:45 lyoko kernel: usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
lug 03 14:26:45 lyoko kernel: usb usb2: Product: xHCI Host Controller
lug 03 14:26:45 lyoko kernel: usb usb2: Manufacturer: Linux 6.15.4-arch2-1 xhci-hcd
lug 03 14:26:45 lyoko kernel: usb usb2: SerialNumber: 0000:00:14.0
lug 03 14:26:45 lyoko kernel: hub 2-0:1.0: USB hub found
lug 03 14:26:45 lyoko kernel: hub 2-0:1.0: 4 ports detected
lug 03 14:26:45 lyoko kernel: xhci_hcd 0000:01:00.2: xHCI Host Controller
lug 03 14:26:45 lyoko kernel: xhci_hcd 0000:01:00.2: new USB bus registered, assigned bus number 3
lug 03 14:26:45 lyoko kernel: xhci_hcd 0000:01:00.2: hcc params 0x0180ff05 hci version 0x110 quirks 0x0000000000000010
lug 03 14:26:45 lyoko kernel: xhci_hcd 0000:01:00.2: xHCI Host Controller
lug 03 14:26:45 lyoko kernel: xhci_hcd 0000:01:00.2: new USB bus registered, assigned bus number 4
lug 03 14:26:45 lyoko kernel: xhci_hcd 0000:01:00.2: Host supports USB 3.1 Enhanced SuperSpeed
lug 03 14:26:45 lyoko kernel: usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.15
lug 03 14:26:45 lyoko kernel: usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
lug 03 14:26:45 lyoko kernel: usb usb3: Product: xHCI Host Controller
lug 03 14:26:45 lyoko kernel: usb usb3: Manufacturer: Linux 6.15.4-arch2-1 xhci-hcd
lug 03 14:26:45 lyoko kernel: usb usb3: SerialNumber: 0000:01:00.2
lug 03 14:26:45 lyoko kernel: hub 3-0:1.0: USB hub found
lug 03 14:26:45 lyoko kernel: hub 3-0:1.0: 2 ports detected
lug 03 14:26:45 lyoko kernel: usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
lug 03 14:26:45 lyoko kernel: usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.15
lug 03 14:26:45 lyoko kernel: usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
lug 03 14:26:45 lyoko kernel: usb usb4: Product: xHCI Host Controller
lug 03 14:26:45 lyoko kernel: usb usb4: Manufacturer: Linux 6.15.4-arch2-1 xhci-hcd
lug 03 14:26:45 lyoko kernel: usb usb4: SerialNumber: 0000:01:00.2
lug 03 14:26:45 lyoko kernel: hub 4-0:1.0: USB hub found
lug 03 14:26:45 lyoko kernel: hub 4-0:1.0: 4 ports detected
lug 03 14:26:45 lyoko kernel: usbcore: registered new interface driver usbserial_generic
lug 03 14:26:45 lyoko kernel: usbserial: USB Serial support registered for generic
lug 03 14:26:45 lyoko kernel: i8042: PNP: No PS/2 controller found.
lug 03 14:26:45 lyoko kernel: rtc_cmos rtc_cmos: RTC can wake from S4
lug 03 14:26:45 lyoko kernel: rtc_cmos rtc_cmos: registered as rtc0
lug 03 14:26:45 lyoko kernel: rtc_cmos rtc_cmos: setting system clock to 2025-07-03T12:26:44 UTC (1751545604)
lug 03 14:26:45 lyoko kernel: rtc_cmos rtc_cmos: alarms up to one month, y3k, 114 bytes nvram
lug 03 14:26:45 lyoko kernel: intel_pstate: Intel P-state driver initializing
lug 03 14:26:45 lyoko kernel: intel_pstate: HWP enabled
lug 03 14:26:45 lyoko kernel: simple-framebuffer simple-framebuffer.0: [drm] Registered 1 planes with drm panic
lug 03 14:26:45 lyoko kernel: [drm] Initialized simpledrm 1.0.0 for simple-framebuffer.0 on minor 0
lug 03 14:26:45 lyoko kernel: fbcon: Deferring console take-over
lug 03 14:26:45 lyoko kernel: simple-framebuffer simple-framebuffer.0: [drm] fb0: simpledrmdrmfb frame buffer device
lug 03 14:26:45 lyoko kernel: hid: raw HID events driver (C) Jiri Kosina
lug 03 14:26:45 lyoko kernel: usbcore: registered new interface driver usbhid
lug 03 14:26:45 lyoko kernel: usbhid: USB HID core driver
lug 03 14:26:45 lyoko kernel: drop_monitor: Initializing network drop monitor service
lug 03 14:26:45 lyoko kernel: NET: Registered PF_INET6 protocol family
lug 03 14:26:45 lyoko kernel: Segment Routing with IPv6
lug 03 14:26:45 lyoko kernel: RPL Segment Routing with IPv6
lug 03 14:26:45 lyoko kernel: In-situ OAM (IOAM) with IPv6
lug 03 14:26:45 lyoko kernel: NET: Registered PF_PACKET protocol family
lug 03 14:26:45 lyoko kernel: microcode: Current revision: 0x0000003a
lug 03 14:26:45 lyoko kernel: IPI shorthand broadcast: enabled
lug 03 14:26:45 lyoko kernel: sched_clock: Marking stable (376000759, 4528902)->(398285057, -17755396)
lug 03 14:26:45 lyoko kernel: registered taskstats version 1
lug 03 14:26:45 lyoko kernel: Loading compiled-in X.509 certificates
lug 03 14:26:45 lyoko kernel: Loaded X.509 cert 'Build time autogenerated kernel key: 1263cc237f7edc3f3e8acdd3ae1809e6a89d0f66'
lug 03 14:26:45 lyoko kernel: zswap: loaded using pool zstd/zsmalloc
lug 03 14:26:45 lyoko kernel: Demotion targets for Node 0: null
lug 03 14:26:45 lyoko kernel: Key type .fscrypt registered
lug 03 14:26:45 lyoko kernel: Key type fscrypt-provisioning registered
lug 03 14:26:45 lyoko kernel: Btrfs loaded, zoned=yes, fsverity=yes
lug 03 14:26:45 lyoko kernel: Key type big_key registered
lug 03 14:26:45 lyoko kernel: integrity: Loading X.509 certificate: UEFI:db
lug 03 14:26:45 lyoko kernel: integrity: Loaded X.509 cert 'Microsoft Corporation UEFI CA 2011: 13adbf4309bd82709c8cd54f316ed522988a1bd4'
lug 03 14:26:45 lyoko kernel: integrity: Loading X.509 certificate: UEFI:db
lug 03 14:26:45 lyoko kernel: integrity: Loaded X.509 cert 'Microsoft Windows Production PCA 2011: a92902398e16c49778cd90f99e4f9ae17c55af53'
lug 03 14:26:45 lyoko kernel: integrity: Loading X.509 certificate: UEFI:db
lug 03 14:26:45 lyoko kernel: integrity: Loaded X.509 cert 'Microsoft Corporation: Windows UEFI CA 2023: aefc5fbbbe055d8f8daa585473499417ab5a5272'
lug 03 14:26:45 lyoko kernel: integrity: Loading X.509 certificate: UEFI:db
lug 03 14:26:45 lyoko kernel: integrity: Loaded X.509 cert 'Microsoft UEFI CA 2023: 81aa6b3244c935bce0d6628af39827421e32497d'
lug 03 14:26:45 lyoko kernel: integrity: Loading X.509 certificate: UEFI:db
lug 03 14:26:45 lyoko kernel: integrity: Loaded X.509 cert 'MSI SHIP DB: ebc30d5be5f35f8041c1c2d9e613eee2'
lug 03 14:26:45 lyoko kernel: PM: Magic number: 1:876:429
lug 03 14:26:45 lyoko kernel: acpi ACPI0007:3a: hash matches
lug 03 14:26:45 lyoko kernel: RAS: Correctable Errors collector initialized.
lug 03 14:26:45 lyoko kernel: clk: Disabling unused clocks
lug 03 14:26:45 lyoko kernel: PM: genpd: Disabling unused power domains
lug 03 14:26:45 lyoko kernel: usb 1-7: new low-speed USB device number 2 using xhci_hcd
lug 03 14:26:45 lyoko kernel: ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
lug 03 14:26:45 lyoko kernel: ata8: SATA link down (SStatus 4 SControl 300)
lug 03 14:26:45 lyoko kernel: ata6: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
lug 03 14:26:45 lyoko kernel: ata7: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
lug 03 14:26:45 lyoko kernel: ata7.00: ATA-11: KINGSTON SA400S37240G, SBFKB1D1, max UDMA/133
lug 03 14:26:45 lyoko kernel: ata7.00: 468862128 sectors, multi 16: LBA48 NCQ (depth 32), AA
lug 03 14:26:45 lyoko kernel: ata6.00: ATA-8: ST1000DM003-9YN162, CC4B, max UDMA/133
lug 03 14:26:45 lyoko kernel: ata6.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 32), AA
lug 03 14:26:45 lyoko kernel: ata6.00: configured for UDMA/133
lug 03 14:26:45 lyoko kernel: ata7.00: configured for UDMA/133
lug 03 14:26:45 lyoko kernel: ata5.00: ATA-8: WDC WD3200BEVT-22ZCT0, 11.01A11, max UDMA/133
lug 03 14:26:45 lyoko kernel: ata5.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 32), AA
lug 03 14:26:45 lyoko kernel: ata5.00: configured for UDMA/133
lug 03 14:26:45 lyoko kernel: scsi 4:0:0:0: Direct-Access ATA WDC WD3200BEVT-2 1A11 PQ: 0 ANSI: 5
lug 03 14:26:45 lyoko kernel: sd 4:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
lug 03 14:26:45 lyoko kernel: sd 4:0:0:0: [sda] Write Protect is off
lug 03 14:26:45 lyoko kernel: sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00
lug 03 14:26:45 lyoko kernel: sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
lug 03 14:26:45 lyoko kernel: sd 4:0:0:0: [sda] Preferred minimum I/O size 512 bytes
lug 03 14:26:45 lyoko kernel: scsi 5:0:0:0: Direct-Access ATA ST1000DM003-9YN1 CC4B PQ: 0 ANSI: 5
lug 03 14:26:45 lyoko kernel: sd 5:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
lug 03 14:26:45 lyoko kernel: sd 5:0:0:0: [sdb] 4096-byte physical blocks
lug 03 14:26:45 lyoko kernel: sd 5:0:0:0: [sdb] Write Protect is off
lug 03 14:26:45 lyoko kernel: sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
lug 03 14:26:45 lyoko kernel: sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
lug 03 14:26:45 lyoko kernel: sd 5:0:0:0: [sdb] Preferred minimum I/O size 4096 bytes
lug 03 14:26:45 lyoko kernel: scsi 6:0:0:0: Direct-Access ATA KINGSTON SA400S3 B1D1 PQ: 0 ANSI: 5
lug 03 14:26:45 lyoko kernel: sd 6:0:0:0: [sdc] 468862128 512-byte logical blocks: (240 GB/224 GiB)
lug 03 14:26:45 lyoko kernel: sd 6:0:0:0: [sdc] Write Protect is off
lug 03 14:26:45 lyoko kernel: sd 6:0:0:0: [sdc] Mode Sense: 00 3a 00 00
lug 03 14:26:45 lyoko kernel: sd 6:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
lug 03 14:26:45 lyoko kernel: sd 6:0:0:0: [sdc] Preferred minimum I/O size 512 bytes
lug 03 14:26:45 lyoko kernel: sdc: sdc1 sdc2 sdc3
lug 03 14:26:45 lyoko kernel: sd 6:0:0:0: [sdc] Attached SCSI disk
lug 03 14:26:45 lyoko kernel: usb 1-7: New USB device found, idVendor=258a, idProduct=0001, bcdDevice= 1.00
lug 03 14:26:45 lyoko kernel: usb 1-7: New USB device strings: Mfr=1, Product=2, SerialNumber=0
lug 03 14:26:45 lyoko kernel: usb 1-7: Product: USB KEYBOARD
lug 03 14:26:45 lyoko kernel: usb 1-7: Manufacturer: SINO WEALTH
lug 03 14:26:45 lyoko kernel: input: SINO WEALTH USB KEYBOARD as /devices/pci0000:00/0000:00:14.0/usb1/1-7/1-7:1.0/0003:258A:0001.0001/input/input3
lug 03 14:26:45 lyoko kernel: sdb: sdb1
lug 03 14:26:45 lyoko kernel: sda: sda1 sda2
lug 03 14:26:45 lyoko kernel: sd 5:0:0:0: [sdb] Attached SCSI disk
lug 03 14:26:45 lyoko kernel: sd 4:0:0:0: [sda] Attached SCSI disk
lug 03 14:26:45 lyoko kernel: Freeing unused decrypted memory: 2028K
lug 03 14:26:45 lyoko kernel: Freeing unused kernel image (initmem) memory: 4632K
lug 03 14:26:45 lyoko kernel: Write protecting the kernel read-only data: 38912k
lug 03 14:26:45 lyoko kernel: Freeing unused kernel image (text/rodata gap) memory: 784K
lug 03 14:26:45 lyoko kernel: Freeing unused kernel image (rodata/data gap) memory: 1912K
lug 03 14:26:45 lyoko kernel: x86/mm: Checked W+X mappings: passed, no W+X pages found.
lug 03 14:26:45 lyoko kernel: rodata_test: all tests were successful
lug 03 14:26:45 lyoko kernel: Run /init as init process
lug 03 14:26:45 lyoko kernel: with arguments:
lug 03 14:26:45 lyoko kernel: /init
lug 03 14:26:45 lyoko kernel: with environment:
lug 03 14:26:45 lyoko kernel: HOME=/
lug 03 14:26:45 lyoko kernel: TERM=linux
lug 03 14:26:45 lyoko kernel: BOOT_IMAGE=/boot/vmlinuz-linux
lug 03 14:26:45 lyoko kernel: hid-generic 0003:258A:0001.0001: input,hidraw0: USB HID v1.10 Keyboard [SINO WEALTH USB KEYBOARD] on usb-0000:00:14.0-7/input0
lug 03 14:26:45 lyoko kernel: input: SINO WEALTH USB KEYBOARD System Control as /devices/pci0000:00/0000:00:14.0/usb1/1-7/1-7:1.1/0003:258A:0001.0002/input/input4
lug 03 14:26:45 lyoko kernel: Key type psk registered
lug 03 14:26:45 lyoko kernel: nvme nvme0: pci function 0000:02:00.0
lug 03 14:26:45 lyoko kernel: input: SINO WEALTH USB KEYBOARD Consumer Control as /devices/pci0000:00/0000:00:14.0/usb1/1-7/1-7:1.1/0003:258A:0001.0002/input/input5
lug 03 14:26:45 lyoko kernel: hid-generic 0003:258A:0001.0002: input,hiddev96,hidraw1: USB HID v1.10 Device [SINO WEALTH USB KEYBOARD] on usb-0000:00:14.0-7/input1
lug 03 14:26:45 lyoko kernel: nvme nvme0: allocated 64 MiB host memory buffer (16 segments).
lug 03 14:26:45 lyoko kernel: nvme nvme0: 8/0/0 default/read/poll queues
lug 03 14:26:45 lyoko kernel: nvme0n1: p1 p2 p3 p4 p5 p6 p7
lug 03 14:26:45 lyoko kernel: usb 1-8: new full-speed USB device number 3 using xhci_hcd
lug 03 14:26:45 lyoko kernel: usb 1-8: New USB device found, idVendor=046d, idProduct=c332, bcdDevice= 3.02
lug 03 14:26:45 lyoko kernel: usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=3
lug 03 14:26:45 lyoko kernel: usb 1-8: Product: Gaming Mouse G502
lug 03 14:26:45 lyoko kernel: usb 1-8: Manufacturer: Logitech
lug 03 14:26:45 lyoko kernel: usb 1-8: SerialNumber: 158938563532
lug 03 14:26:45 lyoko kernel: input: Logitech Gaming Mouse G502 as /devices/pci0000:00/0000:00:14.0/usb1/1-8/1-8:1.0/0003:046D:C332.0003/input/input6
lug 03 14:26:45 lyoko kernel: hid-generic 0003:046D:C332.0003: input,hidraw2: USB HID v1.11 Mouse [Logitech Gaming Mouse G502] on usb-0000:00:14.0-8/input0
lug 03 14:26:45 lyoko kernel: input: Logitech Gaming Mouse G502 Keyboard as /devices/pci0000:00/0000:00:14.0/usb1/1-8/1-8:1.1/0003:046D:C332.0004/input/input7
lug 03 14:26:45 lyoko kernel: hid-generic 0003:046D:C332.0004: input,hiddev97,hidraw3: USB HID v1.11 Keyboard [Logitech Gaming Mouse G502] on usb-0000:00:14.0-8/input1
lug 03 14:26:45 lyoko kernel: usb 1-9: new high-speed USB device number 4 using xhci_hcd
lug 03 14:26:45 lyoko kernel: usb 1-9: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=60.90
lug 03 14:26:45 lyoko kernel: usb 1-9: New USB device strings: Mfr=0, Product=1, SerialNumber=0
lug 03 14:26:45 lyoko kernel: usb 1-9: Product: USB2.0 Hub
lug 03 14:26:45 lyoko kernel: hub 1-9:1.0: USB hub found
lug 03 14:26:45 lyoko kernel: hub 1-9:1.0: 4 ports detected
lug 03 14:26:45 lyoko kernel: usb: port power management may be unreliable
lug 03 14:26:45 lyoko kernel: fbcon: Taking over console
lug 03 14:26:45 lyoko kernel: Console: switching to colour frame buffer device 240x67
lug 03 14:26:45 lyoko kernel: EXT4-fs (nvme0n1p6): mounted filesystem 1d61a5b2-8700-4954-8d30-c4288198c34c r/w with ordered data mode. Quota mode: none.
lug 03 14:26:45 lyoko systemd[1]: systemd 257.7-1-arch running in system mode (+PAM +AUDIT -SELINUX -APPARMOR -IMA +IPE +SMACK +SECCOMP +GCRYPT +GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBCRYPTSETUP_PLUGINS +LIBFDISK +PCRE2 +PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD +BPF_FRAMEWORK +BTF +XKBCOMMON +UTMP -SYSVINIT +LIBARCHIVE)
lug 03 14:26:45 lyoko systemd[1]: Detected architecture x86-64.
lug 03 14:26:45 lyoko systemd[1]: Hostname set to <lyoko>.
lug 03 14:26:45 lyoko kernel: usb 1-9.1: new full-speed USB device number 5 using xhci_hcd
lug 03 14:26:45 lyoko systemd[1]: bpf-restrict-fs: LSM BPF program attached
lug 03 14:26:45 lyoko systemd[1]: Queued start job for default target Graphical Interface.
lug 03 14:26:45 lyoko systemd[1]: Created slice Slice /system/dirmngr.
lug 03 14:26:45 lyoko systemd[1]: Created slice Slice /system/getty.
lug 03 14:26:45 lyoko systemd[1]: Created slice Slice /system/gpg-agent.
lug 03 14:26:45 lyoko systemd[1]: Created slice Slice /system/gpg-agent-browser.
lug 03 14:26:45 lyoko systemd[1]: Created slice Slice /system/gpg-agent-extra.
lug 03 14:26:45 lyoko systemd[1]: Created slice Slice /system/gpg-agent-ssh.
lug 03 14:26:45 lyoko systemd[1]: Created slice Slice /system/keyboxd.
lug 03 14:26:45 lyoko systemd[1]: Created slice Slice /system/modprobe.
lug 03 14:26:45 lyoko systemd[1]: Created slice User and Session Slice.
lug 03 14:26:45 lyoko systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
lug 03 14:26:45 lyoko systemd[1]: Started Forward Password Requests to Wall Directory Watch.
lug 03 14:26:45 lyoko systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
lug 03 14:26:45 lyoko systemd[1]: Expecting device /dev/nvme0n1p4...
lug 03 14:26:45 lyoko systemd[1]: Expecting device /dev/nvme0n1p5...
lug 03 14:26:45 lyoko systemd[1]: Reached target Local Encrypted Volumes.
lug 03 14:26:45 lyoko systemd[1]: Reached target Login Prompts.
lug 03 14:26:45 lyoko systemd[1]: Reached target Local Integrity Protected Volumes.
lug 03 14:26:45 lyoko systemd[1]: Reached target Path Units.
lug 03 14:26:45 lyoko systemd[1]: Reached target Remote File Systems.
lug 03 14:26:45 lyoko systemd[1]: Reached target Slice Units.
lug 03 14:26:45 lyoko systemd[1]: Reached target Local Verity Protected Volumes.
lug 03 14:26:45 lyoko systemd[1]: Listening on Device-mapper event daemon FIFOs.
lug 03 14:26:45 lyoko systemd[1]: Listening on Process Core Dump Socket.
lug 03 14:26:45 lyoko systemd[1]: Listening on Credential Encryption/Decryption.
lug 03 14:26:45 lyoko systemd[1]: Listening on Journal Socket (/dev/log).
lug 03 14:26:45 lyoko systemd[1]: Listening on Journal Sockets.
lug 03 14:26:45 lyoko systemd[1]: TPM PCR Measurements was skipped because of an unmet condition check (ConditionSecurity=measured-uki).
lug 03 14:26:45 lyoko systemd[1]: Make TPM PCR Policy was skipped because of an unmet condition check (ConditionSecurity=measured-uki).
lug 03 14:26:45 lyoko systemd[1]: Listening on udev Control Socket.
lug 03 14:26:45 lyoko systemd[1]: Listening on udev Kernel Socket.
lug 03 14:26:45 lyoko systemd[1]: Listening on User Database Manager Socket.
lug 03 14:26:45 lyoko systemd[1]: Mounting Huge Pages File System...
lug 03 14:26:45 lyoko systemd[1]: Mounting POSIX Message Queue File System...
lug 03 14:26:45 lyoko systemd[1]: Mounting Kernel Debug File System...
lug 03 14:26:45 lyoko systemd[1]: Mounting Kernel Trace File System...
lug 03 14:26:45 lyoko systemd[1]: Starting Create List of Static Device Nodes...
lug 03 14:26:45 lyoko systemd[1]: Starting Load Kernel Module configfs...
lug 03 14:26:45 lyoko systemd[1]: Starting Load Kernel Module dm_mod...
lug 03 14:26:45 lyoko systemd[1]: Starting Load Kernel Module drm...
lug 03 14:26:45 lyoko systemd[1]: Starting Load Kernel Module fuse...
lug 03 14:26:45 lyoko systemd[1]: Starting Load Kernel Module loop...
lug 03 14:26:45 lyoko systemd[1]: File System Check on Root Device was skipped because of an unmet condition check (ConditionPathIsReadWrite=!/).
lug 03 14:26:45 lyoko systemd[1]: Clear Stale Hibernate Storage Info was skipped because of an unmet condition check (ConditionPathExists=/sys/firmware/efi/efivars/HibernateLocation-8cf2644b-4b0b-428f-9387-6d876050dc67).
lug 03 14:26:45 lyoko systemd[1]: Starting Journal Service...
lug 03 14:26:45 lyoko systemd[1]: Starting Load Kernel Modules...
lug 03 14:26:45 lyoko systemd[1]: TPM PCR Machine ID Measurement was skipped because of an unmet condition check (ConditionSecurity=measured-uki).
lug 03 14:26:45 lyoko systemd[1]: Starting Remount Root and Kernel File Systems...
lug 03 14:26:45 lyoko systemd[1]: Early TPM SRK Setup was skipped because of an unmet condition check (ConditionSecurity=measured-uki).
lug 03 14:26:45 lyoko systemd[1]: Starting Load udev Rules from Credentials...
lug 03 14:26:45 lyoko systemd[1]: Starting Coldplug All udev Devices...
lug 03 14:26:45 lyoko systemd[1]: Mounted Huge Pages File System.
lug 03 14:26:45 lyoko systemd[1]: Mounted POSIX Message Queue File System.
lug 03 14:26:45 lyoko systemd[1]: Mounted Kernel Debug File System.
lug 03 14:26:45 lyoko systemd[1]: Mounted Kernel Trace File System.
lug 03 14:26:45 lyoko systemd[1]: Finished Create List of Static Device Nodes.
lug 03 14:26:45 lyoko systemd[1]: modprobe@configfs.service: Deactivated successfully.
lug 03 14:26:45 lyoko systemd[1]: Finished Load Kernel Module configfs.
lug 03 14:26:45 lyoko systemd[1]: modprobe@drm.service: Deactivated successfully.
lug 03 14:26:45 lyoko systemd[1]: Finished Load Kernel Module drm.
lug 03 14:26:45 lyoko systemd[1]: modprobe@fuse.service: Deactivated successfully.
lug 03 14:26:45 lyoko systemd[1]: Finished Load Kernel Module fuse.
lug 03 14:26:45 lyoko systemd[1]: Mounting FUSE Control File System...
lug 03 14:26:45 lyoko systemd[1]: Mounting Kernel Configuration File System...
lug 03 14:26:45 lyoko systemd[1]: Starting Create Static Device Nodes in /dev gracefully...
lug 03 14:26:45 lyoko kernel: loop: module loaded
lug 03 14:26:45 lyoko systemd[1]: modprobe@loop.service: Deactivated successfully.
lug 03 14:26:45 lyoko systemd[1]: Finished Load Kernel Module loop.
lug 03 14:26:45 lyoko systemd[1]: Mounted FUSE Control File System.
lug 03 14:26:45 lyoko systemd[1]: Finished Load udev Rules from Credentials.
lug 03 14:26:45 lyoko systemd[1]: Mounted Kernel Configuration File System.
lug 03 14:26:45 lyoko kernel: EXT4-fs (nvme0n1p6): re-mounted 1d61a5b2-8700-4954-8d30-c4288198c34c.
lug 03 14:26:45 lyoko kernel: device-mapper: uevent: version 1.0.3
lug 03 14:26:45 lyoko kernel: device-mapper: ioctl: 4.49.0-ioctl (2025-01-17) initialised: dm-devel@lists.linux.dev
lug 03 14:26:45 lyoko systemd[1]: Finished Remount Root and Kernel File Systems.
lug 03 14:26:45 lyoko systemd-journald[316]: Collecting audit messages is disabled.
lug 03 14:26:45 lyoko systemd[1]: Rebuild Hardware Database was skipped because of an unmet condition check (ConditionNeedsUpdate=/etc).
lug 03 14:26:45 lyoko systemd[1]: Starting Load/Save OS Random Seed...
lug 03 14:26:45 lyoko systemd[1]: TPM SRK Setup was skipped because of an unmet condition check (ConditionSecurity=measured-uki).
lug 03 14:26:45 lyoko systemd[1]: modprobe@dm_mod.service: Deactivated successfully.
lug 03 14:26:45 lyoko systemd[1]: Finished Load Kernel Module dm_mod.
lug 03 14:26:45 lyoko systemd[1]: Repartition Root Disk was skipped because no trigger condition checks were met.
lug 03 14:26:45 lyoko kernel: i2c_dev: i2c /dev entries driver
lug 03 14:26:45 lyoko systemd[1]: Starting User Database Manager...
lug 03 14:26:45 lyoko systemd[1]: Finished Load/Save OS Random Seed.
lug 03 14:26:45 lyoko systemd[1]: Started User Database Manager.
lug 03 14:26:45 lyoko systemd-journald[316]: Journal started
lug 03 14:26:45 lyoko systemd-journald[316]: Runtime Journal (/run/log/journal/c112474763e341e0b3f353ca9536c241) is 8M, max 788.3M, 780.3M free.
lug 03 14:26:45 lyoko systemd-modules-load[317]: Inserted module 'crypto_user'
lug 03 14:26:45 lyoko systemd-modules-load[317]: Inserted module 'i2c_dev'
lug 03 14:26:45 lyoko systemd[1]: Starting Flush Journal to Persistent Storage...
lug 03 14:26:45 lyoko systemd[1]: Started Journal Service.
lug 03 14:26:45 lyoko systemd[1]: Finished Create Static Device Nodes in /dev gracefully.
lug 03 14:26:45 lyoko systemd-journald[316]: Time spent on flushing to /var/log/journal/c112474763e341e0b3f353ca9536c241 is 137.932ms for 858 entries.
lug 03 14:26:45 lyoko systemd-journald[316]: System Journal (/var/log/journal/c112474763e341e0b3f353ca9536c241) is 40M, max 4G, 3.9G free.
lug 03 14:26:46 lyoko systemd-journald[316]: Received client request to flush runtime journal.
lug 03 14:26:46 lyoko kernel: usb 1-9.1: New USB device found, idVendor=1b3f, idProduct=0329, bcdDevice= 1.00
lug 03 14:26:46 lyoko kernel: usb 1-9.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
lug 03 14:26:46 lyoko kernel: usb 1-9.1: Product: Nor-Tec streaming mic
lug 03 14:26:46 lyoko kernel: usb 1-9.1: Manufacturer: MUSIC-BOOST
lug 03 14:26:46 lyoko kernel: usb 1-9.1: SerialNumber: ES329
lug 03 14:26:46 lyoko kernel: input: MUSIC-BOOST Nor-Tec streaming mic as /devices/pci0000:00/0000:00:14.0/usb1/1-9/1-9.1/1-9.1:1.3/0003:1B3F:0329.0005/input/input10
lug 03 14:26:46 lyoko kernel: hid-generic 0003:1B3F:0329.0005: input,hidraw4: USB HID v2.01 Device [MUSIC-BOOST Nor-Tec streaming mic] on usb-0000:00:14.0-9.1/input3
lug 03 14:26:46 lyoko kernel: mousedev: PS/2 mouse device common for all mice
lug 03 14:26:45 lyoko systemd[1]: Create System Users was skipped because no trigger condition checks were met.
lug 03 14:26:45 lyoko systemd[1]: Starting Create Static Device Nodes in /dev...
lug 03 14:26:46 lyoko systemd[1]: Finished Create Static Device Nodes in /dev.
lug 03 14:26:46 lyoko systemd[1]: Reached target Preparation for Local File Systems.
lug 03 14:26:46 lyoko systemd[1]: Starting Rule-based Manager for Device Events and Files...
lug 03 14:26:46 lyoko systemd[1]: Finished Coldplug All udev Devices.
lug 03 14:26:46 lyoko systemd-udevd[356]: Using default interface naming scheme 'v257'.
lug 03 14:26:46 lyoko systemd[1]: Started Rule-based Manager for Device Events and Files.
lug 03 14:26:46 lyoko systemd[1]: Reached target Trusted Platform Module.
lug 03 14:26:46 lyoko systemd[1]: Finished Flush Journal to Persistent Storage.
lug 03 14:26:46 lyoko systemd[1]: Found device KINGSTON SNV2S1000G 5.
lug 03 14:26:46 lyoko kernel: nvidia-gpu 0000:01:00.3: enabling device (0000 -> 0002)
lug 03 14:26:46 lyoko kernel: intel_pmc_core INT33A1:00: initialized
lug 03 14:26:46 lyoko kernel: EDAC ie31200: No ECC support
lug 03 14:26:46 lyoko kernel: EDAC ie31200: No ECC support
lug 03 14:26:46 lyoko kernel: mei_me 0000:00:16.0: enabling device (0000 -> 0002)
lug 03 14:26:46 lyoko kernel: pps_core: LinuxPPS API ver. 1 registered
lug 03 14:26:46 lyoko kernel: pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
lug 03 14:26:46 lyoko kernel: input: PC Speaker as /devices/platform/pcspkr/input/input11
lug 03 14:26:46 lyoko systemd[1]: Found device KINGSTON SNV2S1000G 4.
lug 03 14:26:46 lyoko kernel: PTP clock support registered
lug 03 14:26:46 lyoko kernel: spi-nor spi0.0: supply vcc not found, using dummy regulator
lug 03 14:26:46 lyoko kernel: i801_smbus 0000:00:1f.4: SPD Write Disable is set
lug 03 14:26:46 lyoko kernel: i801_smbus 0000:00:1f.4: SMBus using PCI interrupt
lug 03 14:26:46 lyoko kernel: RAPL PMU: API unit is 2^-32 Joules, 2 fixed counters, 655360 ms ovfl timer
lug 03 14:26:46 lyoko kernel: RAPL PMU: hw unit of domain pp0-core 2^-14 Joules
lug 03 14:26:46 lyoko kernel: RAPL PMU: hw unit of domain package 2^-14 Joules
lug 03 14:26:46 lyoko kernel: Creating 1 MTD partitions on "0000:00:1f.5":
lug 03 14:26:46 lyoko kernel: 0x000000000000-0x000002000000 : "BIOS"
lug 03 14:26:46 lyoko systemd[1]: Activating swap /dev/nvme0n1p4...
lug 03 14:26:46 lyoko systemd[1]: Starting Virtual Console Setup...
lug 03 14:26:46 lyoko kernel: i2c i2c-1: Successfully instantiated SPD at 0x50
lug 03 14:26:46 lyoko kernel: e1000e: Intel(R) PRO/1000 Network Driver
lug 03 14:26:46 lyoko kernel: e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
lug 03 14:26:46 lyoko kernel: e1000e 0000:00:1f.6: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
lug 03 14:26:46 lyoko kernel: Adding 10485756k swap on /dev/nvme0n1p4. Priority:-2 extents:1 across:10485756k SS
lug 03 14:26:46 lyoko systemd[1]: Activated swap /dev/nvme0n1p4.
lug 03 14:26:46 lyoko systemd[1]: Reached target Swaps.
lug 03 14:26:46 lyoko systemd[1]: Finished Virtual Console Setup.
lug 03 14:26:46 lyoko kernel: iTCO_vendor_support: vendor-support=0
lug 03 14:26:46 lyoko kernel: cryptd: max_cpu_qlen set to 1000
lug 03 14:26:46 lyoko kernel: ee1004 1-0050: 512 byte EE1004-compliant SPD EEPROM, read-only
lug 03 14:26:46 lyoko kernel: iTCO_wdt iTCO_wdt: Found a Intel PCH TCO device (Version=6, TCOBASE=0x0400)
lug 03 14:26:46 lyoko kernel: iTCO_wdt iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
lug 03 14:26:46 lyoko kernel: usb 1-9.2: new high-speed USB device number 6 using xhci_hcd
lug 03 14:26:46 lyoko kernel: snd_hda_intel 0000:00:1f.3: enabling device (0000 -> 0002)
lug 03 14:26:46 lyoko kernel: snd_hda_intel 0000:01:00.1: enabling device (0000 -> 0002)
lug 03 14:26:46 lyoko kernel: snd_hda_intel 0000:01:00.1: Disabling MSI
lug 03 14:26:46 lyoko kernel: snd_hda_intel 0000:01:00.1: Handle vga_switcheroo audio client
lug 03 14:26:46 lyoko kernel: input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input12
lug 03 14:26:46 lyoko kernel: input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input13
lug 03 14:26:46 lyoko kernel: input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input14
lug 03 14:26:46 lyoko kernel: input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input15
lug 03 14:26:46 lyoko systemd[1]: Reached target Sound Card.
lug 03 14:26:46 lyoko kernel: snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC897: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line
lug 03 14:26:46 lyoko kernel: snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
lug 03 14:26:46 lyoko kernel: snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
lug 03 14:26:46 lyoko kernel: snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0
lug 03 14:26:46 lyoko kernel: snd_hda_codec_realtek hdaudioC0D0: inputs:
lug 03 14:26:46 lyoko kernel: snd_hda_codec_realtek hdaudioC0D0: Rear Mic=0x18
lug 03 14:26:46 lyoko kernel: snd_hda_codec_realtek hdaudioC0D0: Front Mic=0x19
lug 03 14:26:46 lyoko kernel: snd_hda_codec_realtek hdaudioC0D0: Line=0x1a
lug 03 14:26:46 lyoko kernel: input: HDA Intel PCH Rear Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input16
lug 03 14:26:46 lyoko kernel: input: HDA Intel PCH Front Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input17
lug 03 14:26:46 lyoko kernel: input: HDA Intel PCH Line as /devices/pci0000:00/0000:00:1f.3/sound/card0/input18
lug 03 14:26:46 lyoko kernel: input: HDA Intel PCH Line Out as /devices/pci0000:00/0000:00:1f.3/sound/card0/input19
lug 03 14:26:46 lyoko kernel: input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1f.3/sound/card0/input20
lug 03 14:26:46 lyoko kernel: usb 1-9.2: New USB device found, idVendor=04e8, idProduct=6864, bcdDevice= c.00
lug 03 14:26:46 lyoko kernel: usb 1-9.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
lug 03 14:26:46 lyoko kernel: usb 1-9.2: Product: SAMSUNG_Android
lug 03 14:26:46 lyoko kernel: usb 1-9.2: Manufacturer: SAMSUNG
lug 03 14:26:46 lyoko kernel: usb 1-9.2: SerialNumber: RFCN20ABSPX
lug 03 14:26:46 lyoko kernel: intel_tcc_cooling: Programmable TCC Offset detected
lug 03 14:26:46 lyoko kernel: mc: Linux media interface: v0.10
lug 03 14:26:46 lyoko kernel: intel_rapl_msr: PL4 support detected.
lug 03 14:26:46 lyoko kernel: intel_rapl_common: Found RAPL domain package
lug 03 14:26:46 lyoko kernel: intel_rapl_common: Found RAPL domain core
lug 03 14:26:46 lyoko kernel: usbcore: registered new interface driver cdc_ether
lug 03 14:26:46 lyoko kernel: rndis_host 1-9.2:1.0 usb0: register 'rndis_host' at usb-0000:00:14.0-9.2, RNDIS device, 02:3a:07:01:1d:62
lug 03 14:26:46 lyoko kernel: usbcore: registered new interface driver rndis_host
lug 03 14:26:46 lyoko kernel: rndis_host 1-9.2:1.0 enp0s20f0u9u2: renamed from usb0
lug 03 14:26:46 lyoko kernel: usbcore: registered new interface driver snd-usb-audio
lug 03 14:26:46 lyoko kernel: e1000e 0000:00:1f.6: The NVM Checksum Is Not Valid
lug 03 14:26:46 lyoko kernel: e1000e 0000:00:1f.6: probe with driver e1000e failed with error -5
lug 03 14:26:46 lyoko kernel: nvidia: loading out-of-tree module taints kernel.
lug 03 14:26:46 lyoko kernel: nvidia: module license 'NVIDIA' taints kernel.
lug 03 14:26:46 lyoko kernel: Disabling lock debugging due to kernel taint
lug 03 14:26:46 lyoko kernel: nvidia: module verification failed: signature and/or required key missing - tainting kernel
lug 03 14:26:46 lyoko kernel: nvidia: module license taints kernel.
lug 03 14:26:46 lyoko kernel: nvidia-nvlink: Nvlink Core is being initialized, major device number 234
lug 03 14:26:46 lyoko kernel:
lug 03 14:26:46 lyoko kernel: nvidia 0000:01:00.0: vgaarb: VGA decodes changed: olddecodes=io+mem,decodes=none:owns=none
lug 03 14:26:46 lyoko kernel: NVRM: loading NVIDIA UNIX x86_64 Kernel Module 575.64.03 Wed Jun 25 18:40:52 UTC 2025
lug 03 14:26:46 lyoko kernel: nvidia-modeset: Loading NVIDIA Kernel Mode Setting Driver for UNIX platforms 575.64.03 Wed Jun 25 18:07:15 UTC 2025
lug 03 14:26:46 lyoko kernel: nvidia_uvm: module uses symbols nvUvmInterfaceDisableAccessCntr from proprietary module nvidia, inheriting taint.
lug 03 14:26:46 lyoko kernel: [drm] [nvidia-drm] [GPU ID 0x00000100] Loading driver
lug 03 14:26:46 lyoko systemd[1]: Mounting /boot/efi...
lug 03 14:26:46 lyoko systemd[1]: Mounting Temporary Directory /tmp...
lug 03 14:26:46 lyoko systemd[1]: Virtual Machine and Container Storage (Compatibility) was skipped because of an unmet condition check (ConditionPathExists=/var/lib/machines.raw).
lug 03 14:26:46 lyoko systemd[1]: Listening on Disk Image Download Service Socket.
lug 03 14:26:47 lyoko kernel: nvidia-gpu 0000:01:00.3: i2c timeout error e0000000
lug 03 14:26:47 lyoko kernel: ucsi_ccg 0-0008: i2c_transfer failed -110
lug 03 14:26:47 lyoko kernel: ucsi_ccg 0-0008: ucsi_ccg_init failed - -110
lug 03 14:26:47 lyoko kernel: ucsi_ccg 0-0008: probe with driver ucsi_ccg failed with error -110
lug 03 14:26:47 lyoko systemd[1]: Mounted Temporary Directory /tmp.
lug 03 14:26:47 lyoko systemd-modules-load[317]: Inserted module 'nvidia_uvm'
lug 03 14:26:47 lyoko systemd[1]: Finished Load Kernel Modules.
lug 03 14:26:47 lyoko systemd[1]: Starting Apply Kernel Variables...
lug 03 14:26:47 lyoko kernel: FAT-fs (nvme0n1p5): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
lug 03 14:26:47 lyoko systemd[1]: Mounted /boot/efi.
lug 03 14:26:47 lyoko systemd[1]: Reached target Local File Systems.
lug 03 14:26:47 lyoko systemd[1]: Listening on Boot Entries Service Socket.
lug 03 14:26:47 lyoko systemd[1]: Listening on System Extension Image Management.
lug 03 14:26:47 lyoko systemd[1]: Set Up Additional Binary Formats was skipped because no trigger condition checks were met.
lug 03 14:26:47 lyoko systemd[1]: Update Boot Loader Random Seed was skipped because no trigger condition checks were met.
lug 03 14:26:47 lyoko systemd[1]: Starting Create System Files and Directories...
lug 03 14:26:47 lyoko systemd[1]: Finished Apply Kernel Variables.
lug 03 14:26:47 lyoko systemd[1]: Finished Create System Files and Directories.
lug 03 14:26:47 lyoko systemd[1]: Rebuild Dynamic Linker Cache was skipped because no trigger condition checks were met.
lug 03 14:26:47 lyoko systemd[1]: First Boot Wizard was skipped because of an unmet condition check (ConditionFirstBoot=yes).
lug 03 14:26:47 lyoko systemd[1]: First Boot Complete was skipped because of an unmet condition check (ConditionFirstBoot=yes).
lug 03 14:26:47 lyoko systemd[1]: Rebuild Journal Catalog was skipped because of an unmet condition check (ConditionNeedsUpdate=/var).
lug 03 14:26:47 lyoko systemd[1]: Save Transient machine-id to Disk was skipped because of an unmet condition check (ConditionPathIsMountPoint=/etc/machine-id).
lug 03 14:26:47 lyoko systemd[1]: Update is Completed was skipped because no trigger condition checks were met.
lug 03 14:26:47 lyoko systemd[1]: Starting Record System Boot/Shutdown in UTMP...
lug 03 14:26:47 lyoko systemd[1]: Finished Record System Boot/Shutdown in UTMP.
lug 03 14:26:47 lyoko systemd[1]: Reached target System Initialization.
lug 03 14:26:47 lyoko systemd[1]: Started Refresh existing PGP keys of archlinux-keyring regularly.
lug 03 14:26:47 lyoko systemd[1]: Started Daily verification of password and group files.
lug 03 14:26:47 lyoko systemd[1]: Started Daily Cleanup of Temporary Directories.
lug 03 14:26:47 lyoko systemd[1]: Reached target Timer Units.
lug 03 14:26:47 lyoko systemd[1]: Listening on D-Bus System Message Bus Socket.
lug 03 14:26:47 lyoko systemd[1]: Listening on GnuPG network certificate management daemon for /etc/pacman.d/gnupg.
lug 03 14:26:47 lyoko systemd[1]: Listening on GnuPG cryptographic agent and passphrase cache (access for web browsers) for /etc/pacman.d/gnupg.
lug 03 14:26:47 lyoko systemd[1]: Listening on GnuPG cryptographic agent and passphrase cache (restricted) for /etc/pacman.d/gnupg.
lug 03 14:26:47 lyoko systemd[1]: Listening on GnuPG cryptographic agent (ssh-agent emulation) for /etc/pacman.d/gnupg.
lug 03 14:26:47 lyoko systemd[1]: Listening on GnuPG cryptographic agent and passphrase cache for /etc/pacman.d/gnupg.
lug 03 14:26:47 lyoko systemd[1]: Listening on GnuPG public key management service for /etc/pacman.d/gnupg.
lug 03 14:26:47 lyoko systemd[1]: Listening on OpenSSH Server Socket (systemd-ssh-generator, AF_UNIX Local).
lug 03 14:26:47 lyoko systemd[1]: Listening on Hostname Service Socket.
lug 03 14:26:47 lyoko systemd[1]: Reached target Socket Units.
lug 03 14:26:47 lyoko systemd[1]: Starting D-Bus System Message Bus...
lug 03 14:26:47 lyoko systemd[1]: TPM PCR Barrier (Initialization) was skipped because of an unmet condition check (ConditionSecurity=measured-uki).
lug 03 14:26:47 lyoko systemd[1]: Started D-Bus System Message Bus.
lug 03 14:26:47 lyoko systemd[1]: Reached target Basic System.
lug 03 14:26:47 lyoko systemd[1]: Starting Network Manager...
lug 03 14:26:47 lyoko systemd[1]: Starting User Login Management...
lug 03 14:26:47 lyoko systemd[1]: TPM PCR Barrier (User) was skipped because of an unmet condition check (ConditionSecurity=measured-uki).
lug 03 14:26:47 lyoko dbus-broker-launch[475]: Ready
lug 03 14:26:47 lyoko systemd-logind[478]: Watching system buttons on /dev/input/event2 (Power Button)
lug 03 14:26:47 lyoko systemd-logind[478]: Watching system buttons on /dev/input/event1 (Power Button)
lug 03 14:26:47 lyoko systemd-logind[478]: Watching system buttons on /dev/input/event0 (Sleep Button)
lug 03 14:26:47 lyoko systemd-logind[478]: Watching system buttons on /dev/input/event3 (SINO WEALTH USB KEYBOARD)
lug 03 14:26:47 lyoko systemd-logind[478]: Watching system buttons on /dev/input/event4 (SINO WEALTH USB KEYBOARD System Control)
lug 03 14:26:47 lyoko systemd-logind[478]: Watching system buttons on /dev/input/event7 (Logitech Gaming Mouse G502 Keyboard)
lug 03 14:26:47 lyoko systemd-logind[478]: New seat seat0.
lug 03 14:26:47 lyoko systemd[1]: Started User Login Management.
lug 03 14:26:47 lyoko kernel: [drm] Initialized nvidia-drm 0.0.0 for 0000:01:00.0 on minor 1
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.8850] NetworkManager (version 1.52.0-1) is starting... (boot:ca29eb89-ab85-4582-a677-fb4fad12b5a5)
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.8851] Read config: /etc/NetworkManager/NetworkManager.conf, /usr/lib/NetworkManager/conf.d/20-connectivity.conf
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.8892] manager[0x557357ba68a0]: monitoring kernel firmware directory '/lib/firmware'.
lug 03 14:26:47 lyoko systemd[1]: Starting Hostname Service...
lug 03 14:26:47 lyoko kernel: Console: switching to colour dummy device 80x25
lug 03 14:26:47 lyoko kernel: nvidia 0000:01:00.0: vgaarb: deactivate vga console
lug 03 14:26:47 lyoko systemd[1]: Started Hostname Service.
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9332] hostname: hostname: using hostnamed
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9332] hostname: static hostname changed from (none) to "lyoko"
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9335] dns-mgr: init: dns=default,systemd-resolved rc-manager=symlink
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9370] manager[0x557357ba68a0]: rfkill: Wi-Fi hardware radio set enabled
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9370] manager[0x557357ba68a0]: rfkill: WWAN hardware radio set enabled
lug 03 14:26:47 lyoko systemd[1]: Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9464] Loaded device plugin: NMWwanFactory (/usr/lib/NetworkManager/1.52.0-1/libnm-device-plugin-wwan.so)
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9467] Loaded device plugin: NMAtmManager (/usr/lib/NetworkManager/1.52.0-1/libnm-device-plugin-adsl.so)
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9472] Loaded device plugin: NMBluezManager (/usr/lib/NetworkManager/1.52.0-1/libnm-device-plugin-bluetooth.so)
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9480] Loaded device plugin: NMOvsFactory (/usr/lib/NetworkManager/1.52.0-1/libnm-device-plugin-ovs.so)
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9687] Loaded device plugin: NMTeamFactory (/usr/lib/NetworkManager/1.52.0-1/libnm-device-plugin-team.so)
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9695] Loaded device plugin: NMWifiFactory (/usr/lib/NetworkManager/1.52.0-1/libnm-device-plugin-wifi.so)
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9696] manager: rfkill: Wi-Fi enabled by radio killswitch; enabled by state file
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9697] manager: rfkill: WWAN enabled by radio killswitch; enabled by state file
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9697] manager: Networking is enabled by state file
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9702] settings: Loaded settings plugin: keyfile (internal)
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9710] dhcp: init: Using DHCP client 'internal'
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9711] manager: (lo): new Loopback device (/org/freedesktop/NetworkManager/Devices/1)
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9720] device (lo): state change: unmanaged -> unavailable (reason 'connection-assumed', managed-type: 'external')
lug 03 14:26:47 lyoko systemd[1]: Starting Network Manager Script Dispatcher Service...
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9725] device (lo): state change: unavailable -> disconnected (reason 'connection-assumed', managed-type: 'external')
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9728] device (lo): Activation: starting connection 'lo' (a95c933f-5a4c-4145-b73f-8ff889187c3d)
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9731] manager: (enp0s20f0u9u2): new Ethernet device (/org/freedesktop/NetworkManager/Devices/2)
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9738] settings: (enp0s20f0u9u2): created default wired connection 'Connessione via cavo 1'
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9738] device (enp0s20f0u9u2): state change: unmanaged -> unavailable (reason 'managed', managed-type: 'external')
lug 03 14:26:47 lyoko systemd[1]: Started Network Manager.
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9746] bus-manager: acquired D-Bus service "org.freedesktop.NetworkManager"
lug 03 14:26:47 lyoko systemd[1]: Reached target Network.
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9754] ovsdb: disconnected from ovsdb
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9754] device (lo): state change: disconnected -> prepare (reason 'none', managed-type: 'external')
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9755] device (lo): state change: prepare -> config (reason 'none', managed-type: 'external')
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9756] device (lo): state change: config -> ip-config (reason 'none', managed-type: 'external')
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9757] device (enp0s20f0u9u2): carrier: link connected
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9758] device (lo): state change: ip-config -> ip-check (reason 'none', managed-type: 'external')
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9760] device (enp0s20f0u9u2): state change: unavailable -> disconnected (reason 'carrier-changed', managed-type: 'full')
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9761] policy: auto-activating connection 'Connessione via cavo 1' (06bcf234-9e4e-3c8c-a6c6-3edcfc19c1e7)
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9763] device (enp0s20f0u9u2): Activation: starting connection 'Connessione via cavo 1' (06bcf234-9e4e-3c8c-a6c6-3edcfc19c1e7)
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9763] device (enp0s20f0u9u2): state change: disconnected -> prepare (reason 'none', managed-type: 'full')
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9764] manager: NetworkManager state is now CONNECTING
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9764] device (enp0s20f0u9u2): state change: prepare -> config (reason 'none', managed-type: 'full')
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9766] device (enp0s20f0u9u2): state change: config -> ip-config (reason 'none', managed-type: 'full')
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9767] dhcp4 (enp0s20f0u9u2): activation: beginning transaction (timeout in 45 seconds)
lug 03 14:26:47 lyoko systemd[1]: Starting Permit User Sessions...
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9841] dhcp4 (enp0s20f0u9u2): state changed new lease, address=192.168.150.195, acd pending
lug 03 14:26:47 lyoko systemd[1]: Finished Permit User Sessions.
lug 03 14:26:47 lyoko systemd[1]: Reached target Multi-User System.
lug 03 14:26:47 lyoko systemd[1]: Started Greeter daemon.
lug 03 14:26:47 lyoko systemd[1]: Reached target Graphical Interface.
lug 03 14:26:47 lyoko systemd[1]: Started Network Manager Script Dispatcher Service.
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9876] device (lo): state change: ip-check -> secondaries (reason 'none', managed-type: 'external')
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9877] device (lo): state change: secondaries -> activated (reason 'none', managed-type: 'external')
lug 03 14:26:47 lyoko NetworkManager[477]: <info> [1751545607.9878] device (lo): Activation: successful, device activated.
lug 03 14:26:47 lyoko systemd[1]: Startup finished in 7.550s (firmware) + 3.183s (loader) + 1.572s (kernel) + 2.287s (userspace) = 14.594s.
lug 03 14:26:47 lyoko greetd[519]: config: Config { file: ConfigFile { terminal: ConfigTerminal { vt: Specific(1), switch: true }, general: ConfigGeneral { source_profile: true, runfile: "/run/greetd.run", service: "greetd" }, default_session: ConfigSession { command: "agreety --cmd /bin/sh", user: "greeter", service: "greetd-greeter" }, initial_session: Some(ConfigSession { command: "Hyprland", user: "indra", service: "greetd" }) }, internal: ConfigInternal { session_worker: 0 } }
lug 03 14:26:47 lyoko greetd[521]: config: Config { file: ConfigFile { terminal: ConfigTerminal { vt: None, switch: false }, general: ConfigGeneral { source_profile: true, runfile: "/run/greetd.run", service: "greetd" }, default_session: ConfigSession { command: "", user: "", service: "" }, initial_session: None }, internal: ConfigInternal { session_worker: 11 } }
lug 03 14:26:48 lyoko dbus-broker-launch[475]: Activation request for 'org.freedesktop.home1' failed: The systemd unit 'dbus-org.freedesktop.home1.service' could not be found.
lug 03 14:26:48 lyoko greetd[521]: pam_unix(greetd:session): session opened for user indra(uid=1000) by indra(uid=0)
lug 03 14:26:48 lyoko systemd-logind[478]: New session 1 of user indra.
lug 03 14:26:48 lyoko systemd[1]: Created slice User Slice of UID 1000.
lug 03 14:26:48 lyoko systemd[1]: Starting User Runtime Directory /run/user/1000...
lug 03 14:26:48 lyoko kernel: fbcon: nvidia-drmdrmfb (fb0) is primary device
lug 03 14:26:48 lyoko systemd[1]: Finished User Runtime Directory /run/user/1000.
lug 03 14:26:48 lyoko systemd[1]: Starting User Manager for UID 1000...
lug 03 14:26:48 lyoko kernel: Console: switching to colour frame buffer device 240x67
lug 03 14:26:48 lyoko kernel: nvidia 0000:01:00.0: [drm] fb0: nvidia-drmdrmfb frame buffer device
lug 03 14:26:48 lyoko NetworkManager[477]: <info> [1751545608.1395] dhcp4 (enp0s20f0u9u2): state changed new lease, address=192.168.150.195
lug 03 14:26:48 lyoko NetworkManager[477]: <info> [1751545608.1401] policy: set 'Connessione via cavo 1' (enp0s20f0u9u2) as default for IPv4 routing and DNS
lug 03 14:26:48 lyoko dbus-broker-launch[475]: Activation request for 'org.freedesktop.resolve1' failed: The systemd unit 'dbus-org.freedesktop.resolve1.service' could not be found.
lug 03 14:26:48 lyoko NetworkManager[477]: <info> [1751545608.1439] device (enp0s20f0u9u2): state change: ip-config -> ip-check (reason 'none', managed-type: 'full')
lug 03 14:26:48 lyoko NetworkManager[477]: <info> [1751545608.1455] device (enp0s20f0u9u2): state change: ip-check -> secondaries (reason 'none', managed-type: 'full')
lug 03 14:26:48 lyoko NetworkManager[477]: <info> [1751545608.1457] device (enp0s20f0u9u2): state change: secondaries -> activated (reason 'none', managed-type: 'full')
lug 03 14:26:48 lyoko NetworkManager[477]: <info> [1751545608.1460] manager: NetworkManager state is now CONNECTED_SITE
lug 03 14:26:48 lyoko NetworkManager[477]: <info> [1751545608.1462] device (enp0s20f0u9u2): Activation: successful, device activated.
lug 03 14:26:48 lyoko NetworkManager[477]: <info> [1751545608.1471] manager: startup complete
lug 03 14:26:48 lyoko (systemd)[526]: pam_warn(systemd-user:setcred): function=[pam_sm_setcred] flags=0x8002 service=[systemd-user] terminal=[] user=[indra] ruser=[<unknown>] rhost=[<unknown>]
lug 03 14:26:48 lyoko (systemd)[526]: pam_unix(systemd-user:session): session opened for user indra(uid=1000) by indra(uid=0)
lug 03 14:26:48 lyoko systemd-logind[478]: New session 2 of user indra.
lug 03 14:26:48 lyoko NetworkManager[477]: <info> [1751545608.2409] manager: NetworkManager state is now CONNECTED_GLOBAL
lug 03 14:26:48 lyoko systemd[526]: Queued start job for default target Main User Target.
lug 03 14:26:48 lyoko systemd[526]: Created slice User Application Slice.
lug 03 14:26:48 lyoko systemd[526]: Reached target Paths.
lug 03 14:26:48 lyoko systemd[526]: Reached target Timers.
lug 03 14:26:48 lyoko systemd[526]: Starting D-Bus User Message Bus Socket...
lug 03 14:26:48 lyoko systemd[526]: Listening on GnuPG network certificate management daemon.
lug 03 14:26:48 lyoko systemd[526]: Listening on GnuPG cryptographic agent and passphrase cache (access for web browsers).
lug 03 14:26:48 lyoko systemd[526]: Listening on GnuPG cryptographic agent and passphrase cache (restricted).
lug 03 14:26:48 lyoko systemd[526]: Listening on GnuPG cryptographic agent (ssh-agent emulation).
lug 03 14:26:48 lyoko systemd[526]: Listening on GnuPG cryptographic agent and passphrase cache.
lug 03 14:26:48 lyoko systemd[526]: Listening on GnuPG public key management service.
lug 03 14:26:48 lyoko systemd[526]: Listening on p11-kit server.
lug 03 14:26:48 lyoko systemd[526]: Listening on PipeWire PulseAudio.
lug 03 14:26:48 lyoko systemd[526]: Listening on PipeWire Multimedia System Sockets.
lug 03 14:26:48 lyoko systemd[526]: Listening on D-Bus User Message Bus Socket.
lug 03 14:26:48 lyoko systemd[526]: Reached target Sockets.
lug 03 14:26:48 lyoko systemd[526]: Reached target Basic System.
lug 03 14:26:48 lyoko systemd[526]: Reached target Main User Target.
lug 03 14:26:48 lyoko systemd[526]: Startup finished in 145ms.
lug 03 14:26:48 lyoko systemd[1]: Started User Manager for UID 1000.
lug 03 14:26:48 lyoko systemd[1]: Started Session 1 of User indra.
lug 03 14:26:49 lyoko systemd[526]: Created slice User Core Session Slice.
lug 03 14:26:49 lyoko systemd[526]: Starting D-Bus User Message Bus...
lug 03 14:26:49 lyoko dbus-broker-launch[574]: Service file '/usr/share/dbus-1/services/org.erikreider.swaync.service' is not named after the D-Bus name 'org.freedesktop.Notifications'.
lug 03 14:26:49 lyoko dbus-broker-launch[574]: Service file '/usr/share/dbus-1/services/org.xfce.Thunar.FileManager1.service' is not named after the D-Bus name 'org.freedesktop.FileManager1'.
lug 03 14:26:49 lyoko dbus-broker-launch[574]: Policy to allow eavesdropping in /usr/share/dbus-1/session.conf +31: Eavesdropping is deprecated and ignored
lug 03 14:26:49 lyoko dbus-broker-launch[574]: Policy to allow eavesdropping in /usr/share/dbus-1/session.conf +33: Eavesdropping is deprecated and ignored
lug 03 14:26:49 lyoko systemd[526]: Started D-Bus User Message Bus.
lug 03 14:26:49 lyoko dbus-broker-launch[574]: Ready
lug 03 14:26:49 lyoko systemd[526]: Starting User preferences database...
lug 03 14:26:49 lyoko systemd[526]: Started User preferences database.
lug 03 14:26:49 lyoko systemd[526]: Starting Accessibility services bus...
lug 03 14:26:49 lyoko systemd[526]: Started Accessibility services bus.
lug 03 14:26:49 lyoko dbus-broker-launch[607]: Ready
lug 03 14:26:49 lyoko systemd[526]: Starting Portal service...
lug 03 14:26:49 lyoko systemd[526]: Starting sandboxed app permission store...
lug 03 14:26:49 lyoko systemd[526]: Started sandboxed app permission store.
lug 03 14:26:49 lyoko systemd[526]: Starting flatpak document portal service...
lug 03 14:26:49 lyoko systemd[526]: Started flatpak document portal service.
lug 03 14:26:49 lyoko systemd[1]: Starting RealtimeKit Scheduling Policy Service...
lug 03 14:26:49 lyoko rtkit-daemon[653]: Successfully called chroot.
lug 03 14:26:49 lyoko rtkit-daemon[653]: Successfully dropped privileges.
lug 03 14:26:49 lyoko systemd[1]: Started RealtimeKit Scheduling Policy Service.
lug 03 14:26:49 lyoko rtkit-daemon[653]: Successfully limited resources.
lug 03 14:26:49 lyoko rtkit-daemon[653]: Running.
lug 03 14:26:49 lyoko rtkit-daemon[653]: Watchdog thread running.
lug 03 14:26:49 lyoko rtkit-daemon[653]: Canary thread running.
lug 03 14:26:49 lyoko rtkit-daemon[653]: Supervising 0 threads of 0 processes of 0 users.
lug 03 14:26:49 lyoko rtkit-daemon[653]: Supervising 0 threads of 0 processes of 0 users.
lug 03 14:26:49 lyoko rtkit-daemon[653]: Supervising 0 threads of 0 processes of 0 users.
lug 03 14:26:49 lyoko systemd[526]: Starting Portal service (Hyprland implementation)...
lug 03 14:26:50 lyoko systemd[526]: Started Portal service (Hyprland implementation).
lug 03 14:26:50 lyoko rtkit-daemon[653]: Supervising 0 threads of 0 processes of 0 users.
lug 03 14:26:50 lyoko rtkit-daemon[653]: Supervising 0 threads of 0 processes of 0 users.
lug 03 14:26:50 lyoko rtkit-daemon[653]: Supervising 0 threads of 0 processes of 0 users.
lug 03 14:26:50 lyoko systemd[526]: Started PipeWire Multimedia Service.
lug 03 14:26:50 lyoko systemd[526]: Started Multimedia Service Session Manager.
lug 03 14:26:50 lyoko systemd[526]: Started Portal service.
lug 03 14:26:50 lyoko systemd[526]: Created slice Slice /app/dbus-:1.9-org.a11y.atspi.Registry.
lug 03 14:26:50 lyoko systemd[526]: Started dbus-:1.9-org.a11y.atspi.Registry@0.service.
lug 03 14:26:50 lyoko xdg-desktop-por[621]: Realtime error: Could not get pidns for pid 658: Could not fstatat ns/pid: Non è una directory
lug 03 14:26:50 lyoko xdg-desktop-por[621]: Realtime error: Could not get pidns for pid 658: Could not fstatat ns/pid: Non è una directory
lug 03 14:26:50 lyoko at-spi2-registryd[666]: SpiRegistry daemon is running with well-known name - org.a11y.atspi.Registry
lug 03 14:26:50 lyoko xdg-desktop-por[621]: Realtime error: Could not get pidns for pid 659: Could not fstatat ns/pid: Non è una directory
lug 03 14:26:50 lyoko systemd[526]: Started PipeWire PulseAudio.
lug 03 14:26:50 lyoko xdg-desktop-por[621]: Realtime error: Could not get pidns for pid 659: Could not fstatat ns/pid: Non è una directory
lug 03 14:26:50 lyoko kernel: cfg80211: Loading compiled-in X.509 certificates for regulatory database
lug 03 14:26:50 lyoko kernel: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
lug 03 14:26:50 lyoko kernel: Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600'
lug 03 14:26:50 lyoko kernel: platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
lug 03 14:26:50 lyoko kernel: cfg80211: failed to load regulatory.db
lug 03 14:26:50 lyoko xdg-desktop-por[621]: Realtime error: Could not get pidns for pid 683: Could not fstatat ns/pid: Non è una directory
lug 03 14:26:50 lyoko xdg-desktop-por[621]: Realtime error: Could not get pidns for pid 683: Could not fstatat ns/pid: Non è una directory
lug 03 14:26:50 lyoko wireplumber[659]: default: Failed to get percentage from UPower: org.freedesktop.DBus.Error.NameHasNoOwner
lug 03 14:26:50 lyoko wireplumber[659]: spa.bluez5: BlueZ system service is not available
lug 03 14:26:50 lyoko wireplumber[659]: wp-device: SPA handle 'api.libcamera.enum.manager' could not be loaded; is it installed?
lug 03 14:26:50 lyoko wireplumber[659]: s-monitors-libcamera: PipeWire's libcamera SPA plugin is missing or broken. Some camera types may not be supported.
lug 03 14:26:50 lyoko wireplumber[659]: wp-event-dispatcher: <WpAsyncEventHook:0x562e23bb8080> failed: failed to activate item: Object activation aborted: proxy destroyed
lug 03 14:26:54 lyoko systemd[526]: Starting Swaync notification daemon...
lug 03 14:26:54 lyoko systemd[526]: Started kitty child process: 802 launched by: 796.
lug 03 14:26:54 lyoko swaync[801]: configModel.vala:297: Loading Config: "/etc/xdg/swaync/config.json"
lug 03 14:26:54 lyoko swaync[801]: functions.vala:98: Loading CSS: "/etc/xdg/swaync/style.css"
lug 03 14:26:54 lyoko swaync[801]: functions.vala:112: Loading CSS: "/etc/xdg/swaync/style.css"
lug 03 14:26:54 lyoko swaync[801]: factory.vala:44: Loading widget: inhibitors
lug 03 14:26:54 lyoko swaync[801]: factory.vala:44: Loading widget: title
lug 03 14:26:54 lyoko swaync[801]: factory.vala:44: Loading widget: dnd
lug 03 14:26:54 lyoko systemd[526]: Started Swaync notification daemon.
lug 03 14:26:57 lyoko kernel: platform INT3515:01: deferred probe pending: Serial bus multi instantiate pseudo device driver: Error creating i2c-client, idx 0
lug 03 14:26:57 lyoko sudo[831]: indra : TTY=pts/0 ; PWD=/home/indra ; USER=root ; COMMAND=/usr/bin/journalctl -b
lug 03 14:26:57 lyoko sudo[831]: pam_unix(sudo:session): session opened for user root(uid=0) by indra(uid=1000)Offline
#8 2025-07-03 16:28:55
- seth
- Member
- From: Don't DM me only for attention
- Registered: 2012-09-03
- Posts: 71,628
Re: [SOLVED] Problems with Network on a fresh install.
0x0.st works here, too - no need to copy around the internet 
lug 03 14:26:45 lyoko kernel: pci 0000:00:1f.6: [8086:1a1d] type 00 class 0x020000 conventional PCI endpoint
lug 03 14:26:45 lyoko kernel: pci 0000:00:1f.6: BAR 0 [mem 0x81200000-0x8121ffff]
lug 03 14:26:45 lyoko kernel: pci 0000:00:1f.6: PME# supported from D0 D3hot D3cold
lug 03 14:26:46 lyoko kernel: e1000e 0000:00:1f.6: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
lug 03 14:26:46 lyoko kernel: e1000e 0000:00:1f.6: The NVM Checksum Is Not Valid
lug 03 14:26:46 lyoko kernel: e1000e 0000:00:1f.6: probe with driver e1000e failed with error -5Add "e1000e.debug=16" to the https://wiki.archlinux.org/title/Kernel_parameters - did you at any point boot w/ e1000e.WriteProtectNVM disabled? (do NOT just do that!)
Online
#9 2025-07-03 17:20:29
- Energy0120
- Member
- Registered: 2025-07-02
- Posts: 8
Re: [SOLVED] Problems with Network on a fresh install.
Hi seth, thank you for trying to help me.
I tried adding that line as a parameter to grub but it didn't resolve the issue. Just in case i remade the journalctl at https://0x0.st/80Vg.txt
This is my grub configuration, sorry for the bad quality:
To be honest yesterday night i tried going through this solution, which i think could be it, but when i tried to recompile e1000e i would just get some errors from the source code.
*** The target kernel has CONFIG_MODULE_SIG_ALL enabled, but
*** the signing key cannot be found. Module signing has been
*** disabled for this build.
make[1]: ingresso nella directory «/usr/lib/modules/6.15.4-arch2-1/build»
make[2]: ingresso nella directory «/home/indra/Download/e1000e-3.8.7/src»
CC [M] netdev.o
netdev.c: In function ‘e1000e_down’:
netdev.c:4828:9: error: implicit declaration of function ‘del_timer_sync’; did you mean ‘dev_mc_sync’? [-Wimplicit-function-declaration]
4828 | del_timer_sync(&adapter->watchdog_timer);
| ^~~~~~~~~~~~~~
| dev_mc_sync
In file included from /usr/lib/modules/6.15.4-arch2-1/build/include/linux/string.h:392,
from /usr/lib/modules/6.15.4-arch2-1/build/include/linux/bitmap.h:13,
from /usr/lib/modules/6.15.4-arch2-1/build/include/linux/cpumask.h:12,
from /usr/lib/modules/6.15.4-arch2-1/build/arch/x86/include/asm/paravirt.h:21,
from /usr/lib/modules/6.15.4-arch2-1/build/arch/x86/include/asm/cpuid/api.h:57,
from /usr/lib/modules/6.15.4-arch2-1/build/arch/x86/include/asm/cpuid.h:6,
from /usr/lib/modules/6.15.4-arch2-1/build/arch/x86/include/asm/processor.h:19,
from /usr/lib/modules/6.15.4-arch2-1/build/arch/x86/include/asm/timex.h:5,
from /usr/lib/modules/6.15.4-arch2-1/build/include/linux/timex.h:67,
from /usr/lib/modules/6.15.4-arch2-1/build/include/linux/time32.h:13,
from /usr/lib/modules/6.15.4-arch2-1/build/include/linux/time.h:60,
from /usr/lib/modules/6.15.4-arch2-1/build/include/linux/stat.h:19,
from /usr/lib/modules/6.15.4-arch2-1/build/include/linux/module.h:13,
from netdev.c:6:
netdev.c: In function ‘e1000_set_mac’:
netdev.c:5381:22: warning: passing argument 1 of ‘__builtin_memcpy’ discards ‘const’ qualifier from pointer target type [-Wdiscarded-qualifiers]
5381 | memcpy(netdev->dev_addr, addr->sa_data, netdev->addr_len);
| ~~~~~~^~~~~~~~~~
/usr/lib/modules/6.15.4-arch2-1/build/include/linux/fortify-string.h:645:27: note: in definition of macro ‘__fortify_memcpy_chk’
645 | __underlying_##op(p, q, __copy_size); \
| ^
netdev.c:5381:9: note: in expansion of macro ‘memcpy’
5381 | memcpy(netdev->dev_addr, addr->sa_data, netdev->addr_len);
| ^~~~~~
netdev.c:5381:22: note: expected ‘void *’ but argument is of type ‘const unsigned char *’
5381 | memcpy(netdev->dev_addr, addr->sa_data, netdev->addr_len);
| ~~~~~~^~~~~~~~~~
/usr/lib/modules/6.15.4-arch2-1/build/include/linux/fortify-string.h:645:27: note: in definition of macro ‘__fortify_memcpy_chk’
645 | __underlying_##op(p, q, __copy_size); \
| ^
netdev.c:5381:9: note: in expansion of macro ‘memcpy’
5381 | memcpy(netdev->dev_addr, addr->sa_data, netdev->addr_len);
| ^~~~~~
netdev.c: In function ‘e1000_ioctl’:
netdev.c:7043:24: error: implicit declaration of function ‘e1000e_hwtstamp_get’ [-Wimplicit-function-declaration]
7043 | return e1000e_hwtstamp_get(netdev, ifr);
| ^~~~~~~~~~~~~~~~~~~
netdev.c: In function ‘e1000_print_device_info’:
netdev.c:8172:17: error: implicit declaration of function ‘strlcpy’; did you mean ‘strncpy’? [-Wimplicit-function-declaration]
8172 | strlcpy((char *)pba_str, "Unknown", sizeof(pba_str));
| ^~~~~~~
| strncpy
netdev.c: In function ‘e1000_probe’:
netdev.c:8378:9: error: implicit declaration of function ‘pci_enable_pcie_error_reporting’ [-Wimplicit-function-declaration]
8378 | pci_enable_pcie_error_reporting(pdev);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
netdev.c:8485:9: error: too many arguments to function ‘netif_napi_add’; expected 3, have 4
8485 | netif_napi_add(netdev, &adapter->napi, e1000e_poll, 64);
| ^~~~~~~~~~~~~~ ~~
In file included from netdev.c:13:
/usr/lib/modules/6.15.4-arch2-1/build/include/linux/netdevice.h:2802:1: note: declared here
2802 | netif_napi_add(struct net_device *dev, struct napi_struct *napi,
| ^~~~~~~~~~~~~~
netdev.c:8639:22: warning: passing argument 1 of ‘__builtin_memcpy’ discards ‘const’ qualifier from pointer target type [-Wdiscarded-qualifiers]
8639 | memcpy(netdev->dev_addr, adapter->hw.mac.addr, netdev->addr_len);
| ~~~~~~^~~~~~~~~~
/usr/lib/modules/6.15.4-arch2-1/build/include/linux/fortify-string.h:645:27: note: in definition of macro ‘__fortify_memcpy_chk’
645 | __underlying_##op(p, q, __copy_size); \
| ^
netdev.c:8639:9: note: in expansion of macro ‘memcpy’
8639 | memcpy(netdev->dev_addr, adapter->hw.mac.addr, netdev->addr_len);
| ^~~~~~
netdev.c:8639:22: note: expected ‘void *’ but argument is of type ‘const unsigned char *’
8639 | memcpy(netdev->dev_addr, adapter->hw.mac.addr, netdev->addr_len);
| ~~~~~~^~~~~~~~~~
/usr/lib/modules/6.15.4-arch2-1/build/include/linux/fortify-string.h:645:27: note: in definition of macro ‘__fortify_memcpy_chk’
645 | __underlying_##op(p, q, __copy_size); \
| ^
netdev.c:8639:9: note: in expansion of macro ‘memcpy’
8639 | memcpy(netdev->dev_addr, adapter->hw.mac.addr, netdev->addr_len);
| ^~~~~~
netdev.c: In function ‘e1000_remove’:
netdev.c:8864:9: error: implicit declaration of function ‘pci_disable_pcie_error_reporting’ [-Wimplicit-function-declaration]
8864 | pci_disable_pcie_error_reporting(pdev);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
netdev.c: In function ‘e1000e_set_interrupt_capability’:
netdev.c:2315:35: warning: this statement may fall through [-Wimplicit-fallthrough=]
2315 | adapter->int_mode = E1000E_INT_MODE_MSI;
netdev.c:2317:9: note: here
2317 | case E1000E_INT_MODE_MSI:
| ^~~~
netdev.c: In function ‘e1000e_reset’:
netdev.c:4543:20: warning: this statement may fall through [-Wimplicit-fallthrough=]
4543 | if (adapter->netdev->mtu > ETH_DATA_LEN) {
| ^
netdev.c:4551:9: note: here
4551 | default:
| ^~~~~~~
netdev.c: In function ‘e1000_setup_rctl’:
netdev.c:3566:32: warning: this statement may fall through [-Wimplicit-fallthrough=]
3566 | psrctl |= PAGE_SIZE << E1000_PSRCTL_BSIZE3_SHIFT;
netdev.c:3568:17: note: here
3568 | case 2:
| ^~~~
netdev.c:3569:32: warning: this statement may fall through [-Wimplicit-fallthrough=]
3569 | psrctl |= PAGE_SIZE << E1000_PSRCTL_BSIZE2_SHIFT;
netdev.c:3571:17: note: here
3571 | case 1:
| ^~~~
netdev.c: In function ‘__e1000e_disable_aspm’:
netdev.c:7576:31: warning: this statement may fall through [-Wimplicit-fallthrough=]
7576 | aspm_dis_mask |= PCI_EXP_LNKCTL_ASPM_L0S;
netdev.c:7578:9: note: here
7578 | case PCIE_LINK_STATE_L1:
| ^~~~
make[4]: *** [/usr/lib/modules/6.15.4-arch2-1/build/scripts/Makefile.build:203: netdev.o] Error 1
make[3]: *** [/usr/lib/modules/6.15.4-arch2-1/build/Makefile:2003: .] Error 2
make[2]: *** [/usr/lib/modules/6.15.4-arch2-1/build/Makefile:248: __sub-make] Error 2
make[2]: uscita dalla directory «/home/indra/Download/e1000e-3.8.7/src»
make[1]: *** [Makefile:248: __sub-make] Error 2
make[1]: uscita dalla directory «/usr/lib/modules/6.15.4-arch2-1/build»
make: *** [Makefile:73: default] Error 2Maybe if i use an older version of the code it might compile and let me apply the patch to avoid the nvc checksum?
Offline
#10 2025-07-03 20:30:09
- seth
- Member
- From: Don't DM me only for attention
- Registered: 2012-09-03
- Posts: 71,628
Re: [SOLVED] Problems with Network on a fresh install.
It's not supposed to fix anything, but I hoped to get some debug data from the module and more insight about what's wrong, but nada.
You could test the LTS kernel, but the invalid checksum will rather not go away.
Do you get this when booting some live distro (including the arch install iso)?
Online
#11 2025-07-03 22:15:47
- Energy0120
- Member
- Registered: 2025-07-02
- Posts: 8
Re: [SOLVED] Problems with Network on a fresh install.
Yeah i remember i had no network during installation, so i assume it's not going to fix on a fresh install.
Sorry i forgot to link the solution i was talking about in my last post:
https://superuser.com/a/1106641
Last edited by Energy0120 (2025-07-03 22:28:17)
Offline
#12 2025-07-03 22:26:19
- seth
- Member
- From: Don't DM me only for attention
- Registered: 2012-09-03
- Posts: 71,628
Re: [SOLVED] Problems with Network on a fresh install.
No, and I don't have high hopes for the LTS kernel either (you can still test that, no re-installation required, if you meant that)
This yells that windows is still controlling the NIC and that the driver there has altered its state.
Can you mount the windows ntfs partition from linux w/o getting an error about the FS still being opened?
Online
#13 2025-07-03 22:36:10
- Energy0120
- Member
- Registered: 2025-07-02
- Posts: 8
Re: [SOLVED] Problems with Network on a fresh install.
Yeah i mounted the windows partition already with no issues, even copied files from it, although it was read only.
Sorry i forgot to write a link in my previous posts, i edited it.
Offline
#14 2025-07-04 07:16:34
- seth
- Member
- From: Don't DM me only for attention
- Registered: 2012-09-03
- Posts: 71,628
Re: [SOLVED] Problems with Network on a fresh install.
Have you already tried https://superuser.com/questions/1104537 … 20#1188020 ?
Writing the NVM can completely brick your NIC, so be very careful w/ that.
Online
#15 2025-07-04 17:36:05
- Energy0120
- Member
- Registered: 2025-07-02
- Posts: 8
Re: [SOLVED] Problems with Network on a fresh install.
Hey Seth, i'm not really sure what happened.
I already saw that post and tried it, i think i followed what he said too and enabled only ipv4 but it didnt work.
This time i went back and disabled Network Stack, saved, and now the NIC finally works.
To be honest i did some other things (like the NVM update tool, although i got an error from it) so i'm not 100% sure if it is that but i'm quite confident it was.
I tried going back to the bios and re enabling it and the card works again so i guess all that happened was a refresh in the NVM.
I think all i had to do was play a bit with the Network stack option, enabling, disabling etc to trigger something.
Thank you for the help, let me know i should add more details or if i should post something.
Offline
#16 2025-07-04 18:30:38
- seth
- Member
- From: Don't DM me only for attention
- Registered: 2012-09-03
- Posts: 71,628
Re: [SOLVED] Problems with Network on a fresh install.
let me know i should add more details or if i should post something
Not unless the situation changes.
Please always remember to mark resolved threads by editing your initial posts subject - so others will know that there's no task left, but maybe a solution to find.
Thanks.
nb. that I'm willing to bet your right arm that the situation was initially caused by windows fast start or any other condition that lead to booting a system while another one was in hibernation.
Windows has a habit of re-activating the feature w/ updates, so keep an eye on that.
Online