You are not logged in.
Hi to everybody!!!
I'm a newbie in using archlinux. I decided to use it after my curiosity in learning more about this OS!
I've installed archlinux 0.7.2 in base version and then I upgraded everything.
I've installed KDE, but in configuring my xorg.conf file, I'm having lots of problem.
I've got a notebook, an acer travelmate 611TXV with embedded intel video card (82815 CGC). Typing
lshwd | less
, the monitor shows:
VGA compatible controller: Intel Coorp. |82815 CGC [Chipset Graphics Controller] (vesa)
I should consider vesa driver or not?
When I set xorg.conf (generate with
hwd -xa
command, I create e new device to describe my video card, because there wasn't, like this:
Section "Device"
Identifier "Card0"
Driver "vesa"
VendorName "All"
BoardName "All"
EndSection
typing
startx
kde starts, but it uses a too low video resolution. It should use 1280x768, the lcd is 14.1"
I can't set the right one! how to?
what I have to do with that "Modeline...
that are reater my lcd capabilities? can I delete them?
Over win XP the lcd woks fine at 1280x768 with 60Hz.
Is there someone to help me? Please
Vincenzo
Offline
What do you have in your Section "Screen" ? There needs to be at least the following:
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1280x768@60"
EndSubSection
EndSection
Or equivalent with the correct names.
edit: you should post your entire xorg.conf instead of just sections at a time. It will be a lot easier 8)
Last edited by codemac (2007-03-11 19:03:08)
Offline
Hi!
thanks for your reply!
My xorg.conf is posted as follows. It's very very similar to the original obtained with standard installation steps.
Section "ServerLayout"
Identifier "Xorg Configured"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "PS/2 Mouse" "CorePointer"
# Serial Mouse not detected
# USB Mouse not detected
EndSection
Section "ServerFlags"
Option "AllowMouseOpenFail" "true"
EndSection
Section "Files"
RgbPath "/usr/share/X11/rgb"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/misc:unscaled"
FontPath "/usr/share/fonts/misc"
FontPath "/usr/share/fonts/75dpi:unscaled"
FontPath "/usr/share/fonts/75dpi"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/100dpi"
FontPath "/usr/share/fonts/PEX"
# Additional fonts: Locale, Gimp, TTF...
FontPath "/usr/share/fonts/cyrillic"
# FontPath "/usr/share/lib/X11/fonts/latin2/75dpi"
# FontPath "/usr/share/lib/X11/fonts/latin2/100dpi"
# True type and type1 fonts are also handled via xftlib, see /etc/X11/XftConfig!
FontPath "/usr/share/fonts/Type1"
FontPath "/usr/share/fonts/ttf/western"
FontPath "/usr/share/fonts/ttf/decoratives"
FontPath "/usr/share/fonts/truetype"
FontPath "/usr/share/fonts/truetype/openoffice"
FontPath "/usr/share/fonts/truetype/ttf-bitstream-vera"
FontPath "/usr/share/fonts/latex-ttf-fonts"
FontPath "/usr/share/fonts/defoma/CID"
FontPath "/usr/share/fonts/defoma/TrueType"
EndSection
Section "Module"
Load "ddc" # ddc probing of monitor
Load "dbe"
Load "dri"
Load "extmod"
Load "glx"
Load "bitmap" # bitmap-fonts
Load "type1"
Load "freetype"
Load "record"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "keyboard"
Option "CoreKeyboard"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "it, IT"
Option "XkbVariant" ""
EndSection
Section "InputDevice"
Identifier "Serial Mouse"
Driver "mouse"
Option "Protocol" "Microsoft"
Option "Device" "/dev/ttyS0"
Option "Emulate3Buttons" "true"
Option "Emulate3Timeout" "70"
Option "SendCoreEvents" "true"
EndSection
Section "InputDevice"
Identifier "PS/2 Mouse"
Driver "mouse"
Option "Protocol" "auto"
Option "ZAxisMapping" "4 5"
Option "Device" "/dev/psaux"
Option "Emulate3Buttons" "true"
Option "Emulate3Timeout" "70"
Option "SendCoreEvents" "true"
EndSection
Section "InputDevice"
Identifier "USB Mouse"
Driver "mouse"
Option "Device" "/dev/input/mice"
Option "SendCoreEvents" "true"
Option "Protocol" "IMPS/2"
Option "ZAxisMapping" "4 5"
Option "Buttons" "5"
EndSection
# Auto-generated by Archie mkxcfg
Section "Monitor"
Identifier "Monitor0"
Option "DPMS" "true"
# HorizSync 28.0 - 78.0 # Warning: This may fry very old Monitors
HorizSync 28.0 - 96.0 # Warning: This may fry old Monitors
VertRefresh 50.0 - 75.0 # Very conservative. May flicker.
# VertRefresh 50.0 - 62.0 # Extreme conservative. Will flicker. TFT default.
# Default modes distilled from
# "VESA and Industry Standards and Guide for Computer Display Monitor
# Timing", version 1.0, revision 0.8, adopted September 17, 1998.
# $XFree86: xc/programs/Xserver/hw/xfree86/etc/vesamodes,v 1.4 1999/11/18 16:52:17 tsi Exp $
# 1024x768 @ 60Hz (VESA) hsync: 48.4kHz
ModeLine "1024x768" 65.0 1024 1048 1184 1344 768 771 777 806 -hsync -vsync
# Additional modelines
ModeLine "1800x1440" 230 1800 1896 2088 2392 1440 1441 1444 1490 +HSync +VSync
ModeLine "1800x1440" 250 1800 1896 2088 2392 1440 1441 1444 1490 +HSync +VSync
# Extended modelines with GTF timings
# 640x480 @ 100.00 Hz (GTF) hsync: 50.90 kHz; pclk: 43.16 MHz
ModeLine "640x480" 43.16 640 680 744 848 480 481 484 509 -HSync +Vsync
# 768x576 @ 60.00 Hz (GTF) hsync: 35.82 kHz; pclk: 34.96 MHz
ModeLine "768x576" 34.96 768 792 872 976 576 577 580 597 -HSync +Vsync
# 768x576 @ 72.00 Hz (GTF) hsync: 43.27 kHz; pclk: 42.93 MHz
ModeLine "768x576" 42.93 768 800 880 992 576 577 580 601 -HSync +Vsync
# 768x576 @ 75.00 Hz (GTF) hsync: 45.15 kHz; pclk: 45.51 MHz
ModeLine "768x576" 45.51 768 808 888 1008 576 577 580 602 -HSync +Vsync
# 768x576 @ 85.00 Hz (GTF) hsync: 51.42 kHz; pclk: 51.84 MHz
ModeLine "768x576" 51.84 768 808 888 1008 576 577 580 605 -HSync +Vsync
# 768x576 @ 100.00 Hz (GTF) hsync: 61.10 kHz; pclk: 62.57 MHz
ModeLine "768x576" 62.57 768 816 896 1024 576 577 580 611 -HSync +Vsync
# 800x600 @ 100.00 Hz (GTF) hsync: 63.60 kHz; pclk: 68.18 MHz
ModeLine "800x600" 68.18 800 848 936 1072 600 601 604 636 -HSync +Vsync
# 1024x768 @ 100.00 Hz (GTF) hsync: 81.40 kHz; pclk: 113.31 MHz
ModeLine "1024x768" 113.31 1024 1096 1208 1392 768 769 772 814 -HSync +Vsync
EndSection
# Auto-generated by Archie mkxcfg
Section "Device"
Identifier "Card0"
Driver "vesa"
VendorName "All"
BoardName "All"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultColorDepth 16
Subsection "Display"
Depth 16
Modes "1024x768@60"
EndSubSection
EndSection
Section "DRI"
Mode 0666
EndSection
I don't know why if I change the default color depth to 24, my resolution becomes 640x480!
Please help me!
Thanks for all
Vincenzo
Offline
If you know your video chip and monitor requirements, you may have more luck running xorgconfig. I suspect vesa is not the best driver for your card, and you may have to change the monitor frequencies (in the Monitor section).
larch: http://larch.berlios.de
Offline
hwd never worked great for me, Xorg's inbuilt detection works far better now.
Use:
Xorg -configure
Give that config a shot.
James
Offline
also, get rid of any and all modelines you have that aren't necessary. It will be easier to read through, not to mention you wont be giving X the wrong idea about your monitor.
Offline