Arch Linux

benoitb

Member

Registered: 2007-06-28

Posts: 9

K3B doesn't want to burn my dvds anymore !

I made a video (animated gif) of the problem, it's really strange and I did not have this problem before.
I'm using a USB DVD burner and it is automatically recognized when I plug it in and insert a DVD. But when k3b starts, it disapears and I can't bring it back unless I disconnect and reconnect it.

edit: k3b 1.0.3 on KDEmod 3.5.7, updated daily

Last edited by benoitb (2007-09-09 16:14:12)

benoitb

Member

Registered: 2007-06-28

Posts: 9

Re: K3B doesn't want to burn my dvds anymore !

Here is the relevant part of dmesg:

usb 4-3: new high speed USB device using ehci_hcd and address 2
Device driver usbdev4.2_ep00 lacks bus and class support for being resumed.
usb 4-3: configuration #1 chosen from 1 choice
Device driver usbdev4.2_ep81 lacks bus and class support for being resumed.
Device driver usbdev4.2_ep02 lacks bus and class support for being resumed.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
Device driver host2 lacks bus and class support for being resumed.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
Device driver target2:0:0 lacks bus and class support for being resumed.
scsi 2:0:0:0: CD-ROM            HL-DT-ST DVD-RW GWA-4040N 1.04 PQ: 0 ANSI: 0
Device driver target2:0:1 lacks bus and class support for being resumed.
Device driver target2:0:2 lacks bus and class support for being resumed.
Device driver target2:0:3 lacks bus and class support for being resumed.
Device driver target2:0:4 lacks bus and class support for being resumed.
Device driver target2:0:5 lacks bus and class support for being resumed.
Device driver target2:0:6 lacks bus and class support for being resumed.
Device driver target2:0:7 lacks bus and class support for being resumed.
usb-storage: device scan complete
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 2:0:0:0: Attached scsi CD-ROM sr0
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 2:0:0:0: Attached scsi generic sg1 type 5
cdrom: This disc doesn't have any tracks I recognize!
usb 4-3: USB disconnect, address 2
scsi 2:0:0:0: scsi: Device offlined - not ready after error recovery
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device

benoitb

Member

Registered: 2007-06-28

Posts: 9

Re: K3B doesn't want to burn my dvds anymore !

I investigated more and when I plug in the DVD drive with a CD or DVD I can read it correctly.
When I launch k3b with a CD or with no media, everything seems fine, the DVD burner is not disconnected.
However, as soon as I launch k3B with a DVD in the burner or insert a DVD inside the burner when k3b is launched, the DVD devie disapears with the above log.