You are not logged in.
- Topics: Active | Unanswered
#1 2007-12-01 19:35:56
- sjb933
- Member
- Registered: 2007-01-18
- Posts: 113
[solved] Synaptics touchpad scrolling not working...
I have the device set up as follows in xorg.conf
Load "synaptics"
...
Section "InputDevice"
Identifier "Touchpad"
Driver "synaptics"
Option "Device" "/dev/input/mouse0"
Option "Protocol" "auto-dev"
Option "LeftEdge" "1700"
Option "RightEdge" "5300"
Option "TopEdge" "1700"
Option "BottomEdge" "4200"
Option "FingerLow" "25"
Option "FingerHigh" "30"
Option "MaxTapTime" "180"
Option "MaxTapMove" "220"
Option "VertScrollDelta" "100"
Option "MinSpeed" "0.24"
Option "MaxSpeed" "0.48"
Option "AccelFactor" "0.0100"
Option "SHMConfig" "on"
EndSectionIt works well, but I get no scrolling on the sides. Any ideas? I'm using KDE if that's of any relevance.
Thanks,
Shane
Last edited by sjb933 (2007-12-03 18:24:39)
Offline
#2 2007-12-01 20:35:00
- thayer
- Fellow
- From: Vancouver, BC
- Registered: 2007-05-20
- Posts: 1,560
- Website
Re: [solved] Synaptics touchpad scrolling not working...
Hrmm, it looks good to me... are you sure that "synaptics" is listed in your Modules section, like this:
Section "Module"
Load "synaptics"
EndSectionAlso, I find it handy to enable horizontal scrolling with a two-finger drag (this goes into your InputDevice section with your other settings):
Option " VertTwoFingerScroll" "True" #Virtual scroll when two fingers dragged up/down
Option " HorizTwoFingerScroll" "True" #Virtual scroll when two fingers dragged left/rightthayer williams ~ cinderwick.ca
Offline
#3 2007-12-01 23:23:29
- ibendiben
- Member
- Registered: 2007-10-10
- Posts: 519
Re: [solved] Synaptics touchpad scrolling not working...
Maybe your machine uses different edges. Try changing those values, make 'm smaller.
Offline
#4 2007-12-02 20:17:32
- sjb933
- Member
- Registered: 2007-01-18
- Posts: 113
Re: [solved] Synaptics touchpad scrolling not working...
Yep, i'm positive it's loaded in the modules. 
Offline
#5 2007-12-02 20:33:34
- SiD
- Member
- From: Germany
- Registered: 2006-09-21
- Posts: 729
Re: [solved] Synaptics touchpad scrolling not working...
If you have something like
InputDevice "Touchpad" "AlwaysCore"In the ServerLayout Section, try to change it to
InputDevice "Touchpad" "SendCoreEvents"http://bbs.archlinux.org/viewtopic.php?id=39584
Since some Xorg update AlwaysCore does not work anymore.
EDIT:
Oh, I did not see that just the scrolling functions not working.
Have you any Errors / Warnings in the xorg logfile?
Last edited by SiD (2007-12-02 20:39:35)
Offline
#6 2007-12-03 17:39:08
- sjb933
- Member
- Registered: 2007-01-18
- Posts: 113
Re: [solved] Synaptics touchpad scrolling not working...
Hmm.. I see no errors.
Here is my Xorg.0.log file:
[shane@Shane-Arch ~]$ cat /var/log/Xorg.0.log
X.Org X Server 1.4.0
Release Date: 5 September 2007
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.24-rc1-ARCH i686
Current Operating System: Linux Shane-Arch 2.6.23-ARCH #1 SMP PREEMPT Sun Nov 18 07:43:05 UTC 2007 i686
Build Date: 07 November 2007 11:19:12AM
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Tue Dec 4 11:34:08 2007
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "X.org Configured"
(**) |-->Screen "Screen0" (0)
(**) | |-->Monitor "Monitor0"
(**) | |-->Device "Card0"
(**) |-->Input Device "Alps touchpad"
(**) |-->Input Device "Keyboard0"
(==) Automatically adding devices
(==) Automatically enabling devices
(==) Including the default font path /usr/share/fonts/misc,/usr/share/fonts/100dpi:unscaled,/usr/share/fonts/75dpi:unscaled,/usr/share/fonts/TTF,/usr/share/fonts/Type1.
(**) FontPath set to:
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/TTF,
/usr/share/fonts/Type1,
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/TTF,
/usr/share/fonts/Type1
(**) RgbPath set to "/usr/share/X11/rgb"
(**) ModulePath set to "/usr/lib/xorg/modules"
(II) No default mouse found, adding one
(**) |-->Input Device "<default pointer>"
(II) Open ACPI successful (/var/run/acpid.socket)
(II) Loader magic: 0x81d4540
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.3
X.Org Video Driver: 2.0
X.Org XInput driver : 2.0
X.Org Server Extension : 0.3
X.Org Font Renderer : 0.5
(II) Loader running on linux
(II) LoadModule: "pcidata"
(II) Loading /usr/lib/xorg/modules//libpcidata.so
(II) Module pcidata: vendor="X.Org Foundation"
compiled for 1.4.0, module version = 1.0.0
ABI class: X.Org Video Driver, version 2.0
(++) using VT number 7
(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 8086,3340 card 1028,0191 rev 03 class 06,00,00 hdr 00
(II) PCI: 00:01:0: chip 8086,3341 card 0000,0000 rev 03 class 06,04,00 hdr 01
(II) PCI: 00:1d:0: chip 8086,24c2 card 1028,0191 rev 01 class 0c,03,00 hdr 80
(II) PCI: 00:1d:1: chip 8086,24c4 card 1028,0191 rev 01 class 0c,03,00 hdr 00
(II) PCI: 00:1d:2: chip 8086,24c7 card 1028,0191 rev 01 class 0c,03,00 hdr 00
(II) PCI: 00:1d:7: chip 8086,24cd card 1028,0191 rev 01 class 0c,03,20 hdr 00
(II) PCI: 00:1e:0: chip 8086,2448 card 0000,0000 rev 81 class 06,04,00 hdr 01
(II) PCI: 00:1f:0: chip 8086,24cc card 0000,0000 rev 01 class 06,01,00 hdr 80
(II) PCI: 00:1f:1: chip 8086,24ca card 1028,0191 rev 01 class 01,01,8a hdr 00
(II) PCI: 00:1f:5: chip 8086,24c5 card 1028,0191 rev 01 class 04,01,00 hdr 00
(II) PCI: 00:1f:6: chip 8086,24c6 card 14f1,5422 rev 01 class 07,03,00 hdr 00
(II) PCI: 01:00:0: chip 1002,4e50 card 1028,2001 rev 00 class 03,00,00 hdr 00
(II) PCI: 02:00:0: chip 14e4,4401 card 1028,8127 rev 01 class 02,00,00 hdr 00
(II) PCI: 02:01:0: chip 104c,ac44 card d000,0000 rev 02 class 06,07,00 hdr 82
(II) PCI: 02:01:1: chip 104c,8029 card 1028,0191 rev 00 class 0c,00,10 hdr 80
(II) PCI: 02:03:0: chip 8086,1043 card 8086,2565 rev 04 class 02,80,00 hdr 00
(II) PCI: End of PCI scan
(II) Intel Bridge workaround enabled
(II) Host-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (0,0,3), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 0 I/O range:
[0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[b]
(II) Bus 0 non-prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
(II) Bus 0 prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
(II) PCI-to-PCI bridge:
(II) Bus 1: bridge is at (0:1:0), (0,1,1), BCTRL: 0x000c (VGA_EN is set)
(II) Bus 1 I/O range:
[0] -1 0 0x0000c000 - 0x0000c0ff (0x100) IX[b]
[1] -1 0 0x0000c400 - 0x0000c4ff (0x100) IX[b]
[2] -1 0 0x0000c800 - 0x0000c8ff (0x100) IX[b]
[3] -1 0 0x0000cc00 - 0x0000ccff (0x100) IX[b]
(II) Bus 1 non-prefetchable memory range:
[0] -1 0 0xfc000000 - 0xfdffffff (0x2000000) MX[b]
(II) Bus 1 prefetchable memory range:
[0] -1 0 0xd0000000 - 0xdfffffff (0x10000000) MX[b]
(II) Subtractive PCI-to-PCI bridge:
(II) Bus 2: bridge is at (0:30:0), (0,2,6), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 2 I/O range:
[0] -1 0 0x0000d000 - 0x0000d0ff (0x100) IX[b]
[1] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[b]
[2] -1 0 0x0000d800 - 0x0000d8ff (0x100) IX[b]
[3] -1 0 0x0000dc00 - 0x0000dcff (0x100) IX[b]
[4] -1 0 0x0000e000 - 0x0000e0ff (0x100) IX[b]
[5] -1 0 0x0000e400 - 0x0000e4ff (0x100) IX[b]
[6] -1 0 0x0000e800 - 0x0000e8ff (0x100) IX[b]
[7] -1 0 0x0000ec00 - 0x0000ecff (0x100) IX[b]
(II) Bus 2 non-prefetchable memory range:
[0] -1 0 0xf6000000 - 0xfbffffff (0x6000000) MX[b]
(II) Bus 2 prefetchable memory range:
[0] -1 0 0x40000000 - 0x43ffffff (0x4000000) MX[b]
(II) PCI-to-ISA bridge:
(II) Bus -1: bridge is at (0:31:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set)
(II) PCI-to-CardBus bridge:
(II) Bus 3: bridge is at (2:1:0), (2,3,6), BCTRL: 0x05c0 (VGA_EN is cleared)
(II) Bus 3 I/O range:
[0] -1 0 0x0000d000 - 0x0000d0ff (0x100) IX[b]
[1] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[b]
(II) Bus 3 prefetchable memory range:
[0] -1 0 0x40000000 - 0x43ffffff (0x4000000) MX[b]
(--) PCI:*(1:0:0) ATI Technologies Inc RV350 [Mobility Radeon 9600 M10] rev 0, Mem @ 0xd0000000/28, 0xfcff0000/16, I/O @ 0xc000/8, BIOS @ 0x80000000/17
(II) Addressable bus resource ranges are
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
[1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[b]
(II) OS-reported resource ranges:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
(II) PCI Memory resource overlap reduced 0xe0000000 from 0xe7ffffff to 0xdfffffff
(II) Active PCI resource ranges:
[0] -1 0 0xfaffc000 - 0xfaffcfff (0x1000) MX[b]
[1] -1 0 0xfaff8000 - 0xfaffbfff (0x4000) MX[b]
[2] -1 0 0xfaffd800 - 0xfaffdfff (0x800) MX[b]
[3] -1 0 0xfaffe000 - 0xfaffffff (0x2000) MX[b]
[4] -1 0 0xf4fff400 - 0xf4fff4ff (0x100) MX[b]
[5] -1 0 0xf4fff800 - 0xf4fff9ff (0x200) MX[b]
[6] -1 0 0x44000000 - 0x440003ff (0x400) MX[b]
[7] -1 0 0xf4fffc00 - 0xf4ffffff (0x400) MX[b]
[8] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
[9] -1 0 0xfc000000 - 0xfc01ffff (0x20000) MX[b](B)
[10] -1 0 0xfcff0000 - 0xfcffffff (0x10000) MX[b](B)
[11] -1 0 0xd0000000 - 0xdfffffff (0x10000000) MX[b](B)
[12] -1 0 0x0000b080 - 0x0000b0ff (0x80) IX[b]
[13] -1 0 0x0000b400 - 0x0000b4ff (0x100) IX[b]
[14] -1 0 0x0000bc40 - 0x0000bc7f (0x40) IX[b]
[15] -1 0 0x0000b800 - 0x0000b8ff (0x100) IX[b]
[16] -1 0 0x0000bfa0 - 0x0000bfaf (0x10) IX[b]
[17] -1 0 0x00000374 - 0x00000374 (0x1) IX[b]
[18] -1 0 0x00000170 - 0x00000177 (0x8) IX[b]
[19] -1 0 0x000003f4 - 0x000003f4 (0x1) IX[b]
[20] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[21] -1 0 0x0000bf20 - 0x0000bf3f (0x20) IX[b]
[22] -1 0 0x0000bf40 - 0x0000bf5f (0x20) IX[b]
[23] -1 0 0x0000bf80 - 0x0000bf9f (0x20) IX[b]
[24] -1 0 0x0000c000 - 0x0000c0ff (0x100) IX[b](B)
(II) Active PCI resource ranges after removing overlaps:
[0] -1 0 0xfaffc000 - 0xfaffcfff (0x1000) MX[b]
[1] -1 0 0xfaff8000 - 0xfaffbfff (0x4000) MX[b]
[2] -1 0 0xfaffd800 - 0xfaffdfff (0x800) MX[b]
[3] -1 0 0xfaffe000 - 0xfaffffff (0x2000) MX[b]
[4] -1 0 0xf4fff400 - 0xf4fff4ff (0x100) MX[b]
[5] -1 0 0xf4fff800 - 0xf4fff9ff (0x200) MX[b]
[6] -1 0 0x44000000 - 0x440003ff (0x400) MX[b]
[7] -1 0 0xf4fffc00 - 0xf4ffffff (0x400) MX[b]
[8] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
[9] -1 0 0xfc000000 - 0xfc01ffff (0x20000) MX[b](B)
[10] -1 0 0xfcff0000 - 0xfcffffff (0x10000) MX[b](B)
[11] -1 0 0xd0000000 - 0xdfffffff (0x10000000) MX[b](B)
[12] -1 0 0x0000b080 - 0x0000b0ff (0x80) IX[b]
[13] -1 0 0x0000b400 - 0x0000b4ff (0x100) IX[b]
[14] -1 0 0x0000bc40 - 0x0000bc7f (0x40) IX[b]
[15] -1 0 0x0000b800 - 0x0000b8ff (0x100) IX[b]
[16] -1 0 0x0000bfa0 - 0x0000bfaf (0x10) IX[b]
[17] -1 0 0x00000374 - 0x00000374 (0x1) IX[b]
[18] -1 0 0x00000170 - 0x00000177 (0x8) IX[b]
[19] -1 0 0x000003f4 - 0x000003f4 (0x1) IX[b]
[20] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[21] -1 0 0x0000bf20 - 0x0000bf3f (0x20) IX[b]
[22] -1 0 0x0000bf40 - 0x0000bf5f (0x20) IX[b]
[23] -1 0 0x0000bf80 - 0x0000bf9f (0x20) IX[b]
[24] -1 0 0x0000c000 - 0x0000c0ff (0x100) IX[b](B)
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
(II) All system resource ranges:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xfaffc000 - 0xfaffcfff (0x1000) MX[b]
[5] -1 0 0xfaff8000 - 0xfaffbfff (0x4000) MX[b]
[6] -1 0 0xfaffd800 - 0xfaffdfff (0x800) MX[b]
[7] -1 0 0xfaffe000 - 0xfaffffff (0x2000) MX[b]
[8] -1 0 0xf4fff400 - 0xf4fff4ff (0x100) MX[b]
[9] -1 0 0xf4fff800 - 0xf4fff9ff (0x200) MX[b]
[10] -1 0 0x44000000 - 0x440003ff (0x400) MX[b]
[11] -1 0 0xf4fffc00 - 0xf4ffffff (0x400) MX[b]
[12] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
[13] -1 0 0xfc000000 - 0xfc01ffff (0x20000) MX[b](B)
[14] -1 0 0xfcff0000 - 0xfcffffff (0x10000) MX[b](B)
[15] -1 0 0xd0000000 - 0xdfffffff (0x10000000) MX[b](B)
[16] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[17] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[18] -1 0 0x0000b080 - 0x0000b0ff (0x80) IX[b]
[19] -1 0 0x0000b400 - 0x0000b4ff (0x100) IX[b]
[20] -1 0 0x0000bc40 - 0x0000bc7f (0x40) IX[b]
[21] -1 0 0x0000b800 - 0x0000b8ff (0x100) IX[b]
[22] -1 0 0x0000bfa0 - 0x0000bfaf (0x10) IX[b]
[23] -1 0 0x00000374 - 0x00000374 (0x1) IX[b]
[24] -1 0 0x00000170 - 0x00000177 (0x8) IX[b]
[25] -1 0 0x000003f4 - 0x000003f4 (0x1) IX[b]
[26] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[27] -1 0 0x0000bf20 - 0x0000bf3f (0x20) IX[b]
[28] -1 0 0x0000bf40 - 0x0000bf5f (0x20) IX[b]
[29] -1 0 0x0000bf80 - 0x0000bf9f (0x20) IX[b]
[30] -1 0 0x0000c000 - 0x0000c0ff (0x100) IX[b](B)
(II) "extmod" will be loaded. This was enabled by default and also specified in the config file.
(II) "dbe" will be loaded. This was enabled by default and also specified in the config file.
(II) "glx" will be loaded by default.
(II) "freetype" will be loaded. This was enabled by default and also specified in the config file.
(II) "type1" will be loaded. This was enabled by default and also specified in the config file.
(II) "record" will be loaded. This was enabled by default and also specified in the config file.
(II) "dri" will be loaded. This was enabled by default and also specified in the config file.
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.4.0, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.4.0, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension RECORD
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.4.0, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension XFree86-DRI
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.4.0, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "xtrap"
(II) Loading /usr/lib/xorg/modules/extensions//libxtrap.so
(II) Module xtrap: vendor="X.Org Foundation"
compiled for 1.4.0, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension DEC-XTRAP
(II) LoadModule: "type1"
(II) Loading /usr/lib/xorg/modules/fonts//libtype1.so
(II) Module type1: vendor="X.Org Foundation"
compiled for 1.4.0, module version = 1.0.2
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.5
(II) Loading font Type1
(II) LoadModule: "freetype"
(II) Loading /usr/lib/xorg/modules/fonts//libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
compiled for 1.4.0, module version = 2.1.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.5
(II) Loading font FreeType
(II) LoadModule: "synaptics"
(II) Loading /usr/lib/xorg/modules/input//synaptics_drv.so
(II) Module synaptics: vendor="X.Org Foundation"
compiled for 4.3.99.902, module version = 1.0.0
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 2.0
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 1.4.0, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.3
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "ati"
(II) Loading /usr/lib/xorg/modules/drivers//ati_drv.so
(II) Module ati: vendor="X.Org Foundation"
compiled for 1.4.0, module version = 6.7.195
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 2.0
(II) LoadModule: "synaptics"
(II) Reloading /usr/lib/xorg/modules/input//synaptics_drv.so
(II) LoadModule: "kbd"
(II) Loading /usr/lib/xorg/modules/input//kbd_drv.so
(II) Module kbd: vendor="X.Org Foundation"
compiled for 1.4.0, module version = 1.2.2
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 2.0
(II) LoadModule: "mouse"
(II) Loading /usr/lib/xorg/modules/input//mouse_drv.so
(II) Module mouse: vendor="X.Org Foundation"
compiled for 1.4.0, module version = 1.2.3
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 2.0
(II) ATI: ATI driver wrapper (version 6.7.195) for chipsets: mach64, rage128, radeon
(II) Primary Device is: PCI 01:00:0
(II) Loading sub module "radeon"
(II) LoadModule: "radeon"
(II) Loading /usr/lib/xorg/modules/drivers//radeon_drv.so
(II) Module radeon: vendor="X.Org Foundation"
compiled for 1.4.0, module version = 4.3.0
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 2.0
(II) RADEON: Driver for ATI Radeon chipsets: ATI Radeon QD (AGP),
ATI Radeon QE (AGP), ATI Radeon QF (AGP), ATI Radeon QG (AGP),
ATI Radeon VE/7000 QY (AGP/PCI), ATI Radeon VE/7000 QZ (AGP/PCI),
ATI ES1000 515E (PCI), ATI ES1000 5969 (PCI),
ATI Radeon Mobility M7 LW (AGP),
ATI Mobility FireGL 7800 M7 LX (AGP),
ATI Radeon Mobility M6 LY (AGP), ATI Radeon Mobility M6 LZ (AGP),
ATI Radeon IGP320 (A3) 4136, ATI Radeon IGP320M (U1) 4336,
ATI Radeon IGP330/340/350 (A4) 4137,
ATI Radeon IGP330M/340M/350M (U2) 4337,
ATI Radeon 7000 IGP (A4+) 4237, ATI Radeon Mobility 7000 IGP 4437,
ATI FireGL 8700/8800 QH (AGP), ATI Radeon 8500 QL (AGP),
ATI Radeon 9100 QM (AGP), ATI Radeon 8500 AIW BB (AGP),
ATI Radeon 8500 AIW BC (AGP), ATI Radeon 7500 QW (AGP/PCI),
ATI Radeon 7500 QX (AGP/PCI), ATI Radeon 9000/PRO If (AGP/PCI),
ATI Radeon 9000 Ig (AGP/PCI), ATI FireGL Mobility 9000 (M9) Ld (AGP),
ATI Radeon Mobility 9000 (M9) Lf (AGP),
ATI Radeon Mobility 9000 (M9) Lg (AGP),
ATI Radeon 9100 IGP (A5) 5834,
ATI Radeon Mobility 9100 IGP (U3) 5835, ATI Radeon 9100 PRO IGP 7834,
ATI Radeon Mobility 9200 IGP 7835, ATI Radeon 9250 5960 (AGP),
ATI Radeon 9200 5961 (AGP), ATI Radeon 9200 5962 (AGP),
ATI Radeon 9200SE 5964 (AGP), ATI FireMV 2200 (PCI),
ATI Radeon Mobility 9200 (M9+) 5C61 (AGP),
ATI Radeon Mobility 9200 (M9+) 5C63 (AGP), ATI Radeon 9500 AD (AGP),
ATI Radeon 9500 AE (AGP), ATI Radeon 9600TX AF (AGP),
ATI FireGL Z1 AG (AGP), ATI Radeon 9700 Pro ND (AGP),
ATI Radeon 9700/9500Pro NE (AGP), ATI Radeon 9600TX NF (AGP),
ATI FireGL X1 NG (AGP), ATI Radeon 9600 AP (AGP),
ATI Radeon 9600SE AQ (AGP), ATI Radeon 9600XT AR (AGP),
ATI Radeon 9600 AS (AGP), ATI FireGL T2 AT (AGP),
ATI FireGL RV360 AV (AGP),
ATI Radeon Mobility 9600/9700 (M10/M11) NP (AGP),
ATI Radeon Mobility 9600 (M10) NQ (AGP),
ATI Radeon Mobility 9600 (M11) NR (AGP),
ATI Radeon Mobility 9600 (M10) NS (AGP),
ATI FireGL Mobility T2 (M10) NT (AGP),
ATI FireGL Mobility T2e (M11) NV (AGP), ATI Radeon 9650,
ATI Radeon 9800SE AH (AGP), ATI Radeon 9800 AI (AGP),
ATI Radeon 9800 AJ (AGP), ATI FireGL X2 AK (AGP),
ATI Radeon 9800PRO NH (AGP), ATI Radeon 9800 NI (AGP),
ATI FireGL X2 NK (AGP), ATI Radeon 9800XT NJ (AGP),
ATI Radeon X600 (RV380) 3E50 (PCIE),
ATI FireGL V3200 (RV380) 3E54 (PCIE),
ATI Radeon Mobility X600 (M24) 3150 (PCIE),
ATI Radeon Mobility X300 (M24) 3152 (PCIE),
ATI FireGL M24 GL 3154 (PCIE), ATI Radeon X300 (RV370) 5B60 (PCIE),
ATI Radeon X600 (RV370) 5B62 (PCIE),
ATI Radeon X550 (RV370) 5B63 (PCIE),
ATI FireGL V3100 (RV370) 5B64 (PCIE),
ATI FireMV 2200 PCIE (RV370) 5B65 (PCIE),
ATI Radeon Mobility X300 (M22) 5460 (PCIE),
ATI Radeon Mobility X600 SE (M24C) 5462 (PCIE),
ATI FireGL M22 GL 5464 (PCIE), ATI Radeon XPRESS 200 5A41 (PCIE),
ATI Radeon XPRESS 200M 5A42 (PCIE),
ATI Radeon XPRESS 200 5A61 (PCIE),
ATI Radeon XPRESS 200M 5A62 (PCIE),
ATI Radeon XPRESS 200 5954 (PCIE),
ATI Radeon XPRESS 200M 5955 (PCIE),
ATI Radeon XPRESS 200 5974 (PCIE),
ATI Radeon XPRESS 200M 5975 (PCIE), ATI FireGL V5000 (RV410) (PCIE),
ATI Mobility FireGL V5000 (M26) (PCIE),
ATI Mobility FireGL V5000 (M26) (PCIE),
ATI Mobility Radeon X700 XL (M26) (PCIE),
ATI Mobility Radeon X700 (M26) (PCIE),
ATI Mobility Radeon X700 (M26) (PCIE),
ATI Radeon X700 PRO (RV410) (PCIE),
ATI Radeon X700 XT (RV410) (PCIE), ATI Radeon X700 (RV410) (PCIE),
ATI Radeon X700 SE (RV410) (PCIE), ATI Radeon X700 SE (RV410) (PCIE),
ATI Radeon X800 (R420) JH (AGP), ATI Radeon X800PRO (R420) JI (AGP),
ATI Radeon X800SE (R420) JJ (AGP), ATI Radeon X800 (R420) JK (AGP),
ATI Radeon X800 (R420) JL (AGP), ATI FireGL X3 (R420) JM (AGP),
ATI Radeon Mobility 9800 (M18) JN (AGP),
ATI Radeon X800XT (R420) JP (AGP), ATI Radeon X800 SE (R420) (AGP),
ATI Radeon AIW X800 VE (R420) JT (AGP),
ATI Radeon X800 (R423) UH (PCIE),
ATI Radeon X800PRO (R423) UI (PCIE),
ATI Radeon X800LE (R423) UJ (PCIE),
ATI Radeon X800SE (R423) UK (PCIE),
ATI FireGL V5100 (R423) UQ (PCIE),
ATI FireGL unknown (R423) UR (PCIE),
ATI FireGL unknown (R423) UT (PCIE),
ATI Radeon X800XT (R423) 5D57 (PCIE), ATI FireGL V7100 (R423) (PCIE),
ATI Mobility FireGL V5100 (M28) (PCIE),
ATI Mobility Radeon X800 (M28) (PCIE),
ATI Mobility Radeon X800 XT (M28) (PCIE),
ATI Radeon X800 (R430) (PCIE), ATI Radeon X800 XL (R430) (PCIE),
ATI Radeon X800 SE (R430) (PCIE), ATI Radeon X800 XTP (R430) (PCIE),
ATI Radeon X850 5D4C (PCIE),
ATI unknown Radeon / FireGL (R480) 5D50 (PCIE),
ATI Radeon X850 SE (R480) (PCIE), ATI Radeon X850 PRO (R480) (PCIE),
ATI Radeon X850 XT (R480) (PCIE),
ATI Radeon X850 XT PE (R480) (PCIE),
ATI Radeon X850 PRO (R480) (AGP), ATI Radeon X850 SE (R480) (AGP),
ATI Radeon X850 XT (R480) (AGP), ATI Radeon X850 XT PE (R480) (AGP)
(--) Chipset ATI Radeon Mobility 9600/9700 (M10/M11) NP (AGP) found
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xfaffc000 - 0xfaffcfff (0x1000) MX[b]
[5] -1 0 0xfaff8000 - 0xfaffbfff (0x4000) MX[b]
[6] -1 0 0xfaffd800 - 0xfaffdfff (0x800) MX[b]
[7] -1 0 0xfaffe000 - 0xfaffffff (0x2000) MX[b]
[8] -1 0 0xf4fff400 - 0xf4fff4ff (0x100) MX[b]
[9] -1 0 0xf4fff800 - 0xf4fff9ff (0x200) MX[b]
[10] -1 0 0x44000000 - 0x440003ff (0x400) MX[b]
[11] -1 0 0xf4fffc00 - 0xf4ffffff (0x400) MX[b]
[12] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
[13] -1 0 0xfc000000 - 0xfc01ffff (0x20000) MX[b](B)
[14] -1 0 0xfcff0000 - 0xfcffffff (0x10000) MX[b](B)
[15] -1 0 0xd0000000 - 0xdfffffff (0x10000000) MX[b](B)
[16] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[17] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[18] -1 0 0x0000b080 - 0x0000b0ff (0x80) IX[b]
[19] -1 0 0x0000b400 - 0x0000b4ff (0x100) IX[b]
[20] -1 0 0x0000bc40 - 0x0000bc7f (0x40) IX[b]
[21] -1 0 0x0000b800 - 0x0000b8ff (0x100) IX[b]
[22] -1 0 0x0000bfa0 - 0x0000bfaf (0x10) IX[b]
[23] -1 0 0x00000374 - 0x00000374 (0x1) IX[b]
[24] -1 0 0x00000170 - 0x00000177 (0x8) IX[b]
[25] -1 0 0x000003f4 - 0x000003f4 (0x1) IX[b]
[26] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[27] -1 0 0x0000bf20 - 0x0000bf3f (0x20) IX[b]
[28] -1 0 0x0000bf40 - 0x0000bf5f (0x20) IX[b]
[29] -1 0 0x0000bf80 - 0x0000bf9f (0x20) IX[b]
[30] -1 0 0x0000c000 - 0x0000c0ff (0x100) IX[b](B)
(II) resource ranges after probing:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xfaffc000 - 0xfaffcfff (0x1000) MX[b]
[5] -1 0 0xfaff8000 - 0xfaffbfff (0x4000) MX[b]
[6] -1 0 0xfaffd800 - 0xfaffdfff (0x800) MX[b]
[7] -1 0 0xfaffe000 - 0xfaffffff (0x2000) MX[b]
[8] -1 0 0xf4fff400 - 0xf4fff4ff (0x100) MX[b]
[9] -1 0 0xf4fff800 - 0xf4fff9ff (0x200) MX[b]
[10] -1 0 0x44000000 - 0x440003ff (0x400) MX[b]
[11] -1 0 0xf4fffc00 - 0xf4ffffff (0x400) MX[b]
[12] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
[13] -1 0 0xfc000000 - 0xfc01ffff (0x20000) MX[b](B)
[14] -1 0 0xfcff0000 - 0xfcffffff (0x10000) MX[b](B)
[15] -1 0 0xd0000000 - 0xdfffffff (0x10000000) MX[b](B)
[16] 0 0 0x000a0000 - 0x000affff (0x10000) MS[b]
[17] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[b]
[18] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[b]
[19] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[20] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[21] -1 0 0x0000b080 - 0x0000b0ff (0x80) IX[b]
[22] -1 0 0x0000b400 - 0x0000b4ff (0x100) IX[b]
[23] -1 0 0x0000bc40 - 0x0000bc7f (0x40) IX[b]
[24] -1 0 0x0000b800 - 0x0000b8ff (0x100) IX[b]
[25] -1 0 0x0000bfa0 - 0x0000bfaf (0x10) IX[b]
[26] -1 0 0x00000374 - 0x00000374 (0x1) IX[b]
[27] -1 0 0x00000170 - 0x00000177 (0x8) IX[b]
[28] -1 0 0x000003f4 - 0x000003f4 (0x1) IX[b]
[29] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[30] -1 0 0x0000bf20 - 0x0000bf3f (0x20) IX[b]
[31] -1 0 0x0000bf40 - 0x0000bf5f (0x20) IX[b]
[32] -1 0 0x0000bf80 - 0x0000bf9f (0x20) IX[b]
[33] -1 0 0x0000c000 - 0x0000c0ff (0x100) IX[b](B)
[34] 0 0 0x000003b0 - 0x000003bb (0xc) IS[b]
[35] 0 0 0x000003c0 - 0x000003df (0x20) IS[b]
(II) Setting vga for screen 0.
(II) RADEON(0): MMIO registers at 0xfcff0000: size 64KB
(II) RADEON(0): PCI bus 1 card 0 func 0
(==) RADEON(0): Depth 24, (==) framebuffer bpp 32
(II) RADEON(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
(==) RADEON(0): Default visual is TrueColor
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/lib/xorg/modules//libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
compiled for 1.4.0, module version = 0.1.0
ABI class: X.Org Video Driver, version 2.0
(II) RADEON(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(==) RADEON(0): RGB weight 888
(II) RADEON(0): Using 8 bits per RGB (8 bit DAC)
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/lib/xorg/modules//libint10.so
(II) Module int10: vendor="X.Org Foundation"
compiled for 1.4.0, module version = 1.0.0
ABI class: X.Org Video Driver, version 2.0
(II) RADEON(0): initializing int10
(II) RADEON(0): Primary V_BIOS segment is: 0xc000
(--) RADEON(0): Chipset: "ATI Radeon Mobility 9600/9700 (M10/M11) NP (AGP)" (ChipID = 0x4e50)
(--) RADEON(0): Linear framebuffer at 0xd0000000
(--) RADEON(0): BIOS at 0x80000000
(II) RADEON(0): AGP card detected
(II) RADEON(0): Legacy BIOS detected
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is -1, (No such device or address)
drmOpenDevice: open result is -1, (No such device or address)
drmOpenDevice: Open failed
drmOpenByBusid: Searching for BusID pci:0000:01:00.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 9, (OK)
drmOpenByBusid: drmOpenMinor returns 9
drmOpenByBusid: drmGetBusid reports pci:0000:01:00.0
(II) RADEON(0): [dri] Found DRI library version 1.3.0 and kernel module version 1.28.0
(==) RADEON(0): Page Flipping disabled
(II) RADEON(0): Will try to use DMA for Xv image transfers
(II) RADEON(0): Generation 2 PCI interface, using max accessible memory
(II) RADEON(0): Detected total video RAM=131072K, accessible=262144K (PCI BAR=262144K)
(--) RADEON(0): Mapped VideoRAM: 131072 kByte (128 bit DDR SDRAM)
(II) RADEON(0): Color tiling enabled by default
(II) RADEON(0): Max desktop size set to 2560x1200
(II) RADEON(0): For a larger or smaller max desktop size, add a Virtual line to your xorg.conf
(II) RADEON(0): If you are having trouble with 3D, reduce the desktop size by adjusting the Virtual line to your xorg.conf
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"(II) Module "ddc" already built-in
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"(II) Module "i2c" already built-in
(II) RADEON(0): PLL parameters: rf=2700 rd=6 min=20000 max=35000; xclk=24300
(WW) RADEON(0): LCD DDC Info Table found!
(II) RADEON(0): Bios Connector table:
(II) RADEON(0): Port0: DDCType-3, DACType-0, TMDSType-0, ConnectorType-2
(II) RADEON(0): Port1: DDCType-2, DACType-0, TMDSType-1, ConnectorType-4
(II) RADEON(0): Port4: DDCType-6, DACType-2, TMDSType-2, ConnectorType-1
(II) RADEON(0): Port5: DDCType-0, DACType-1, TMDSType-2, ConnectorType-6
(II) RADEON(0): Output VGA-0 using monitor section Monitor0
(II) RADEON(0): I2C bus "VGA_DDC" initialized.
(II) RADEON(0): Output DVI-0 has no monitor section
(II) RADEON(0): I2C bus "DVI_DDC" initialized.
(II) RADEON(0): External TMDS Table revision: 2
(II) RADEON(0): I2C bus "DVO" initialized.
(II) RADEON(0): I2C device "DVO:RADEON DVO Controller" registered at address 0x70.
(II) RADEON(0): Output LVDS has no monitor section
(II) RADEON(0): I2C bus "GPIO_DDC" initialized.
(II) RADEON(0): Panel ID string: Y0316154X1
(II) RADEON(0): Panel Size from BIOS: 1280x800
(II) RADEON(0): BIOS provided dividers will be used.
(WW) RADEON(0): LVDS Info:
XRes: 1280, YRes: 800, DotClock: 71250
HBlank: 160, HOverPlus: 48, HSyncWidth: 32
VBlank: 23, VOverPlus: 2, VSyncWidth: 6
(II) RADEON(0): Using LVDS Native Mode
(II) RADEON(0): Output S-video has no monitor section
(II) RADEON(0): Default TV standard: NTSC
(II) RADEON(0): TV standards supported by chip: NTSC
(II) RADEON(0): Port0:
Monitor -- AUTO
Connector -- VGA
DAC Type -- Primary
TMDS Type -- None
DDC Type -- VGA_DDC
(II) RADEON(0): Port1:
Monitor -- AUTO
Connector -- DVI-D
DAC Type -- None
TMDS Type -- External
DDC Type -- DVI_DDC
(II) RADEON(0): Port2:
Monitor -- AUTO
Connector -- Proprietary/LVDS
DAC Type -- None
TMDS Type -- None
DDC Type -- GPIO_DDC
(II) RADEON(0): Port3:
Monitor -- AUTO
Connector -- STV
DAC Type -- TVDAC/ExtDAC
TMDS Type -- None
DDC Type -- None
(II) RADEON(0): I2C device "VGA_DDC:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "VGA_DDC:ddc2" removed.
(II) RADEON(0): I2C device "VGA_DDC:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "VGA_DDC:ddc2" removed.
(II) RADEON(0): I2C device "VGA_DDC:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "VGA_DDC:ddc2" removed.
(II) RADEON(0): DDC Type: 3, Detected Monitor Type: 0
finished output detect: 0
(II) RADEON(0): I2C device "DVI_DDC:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "DVI_DDC:ddc2" removed.
(II) RADEON(0): I2C device "DVI_DDC:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "DVI_DDC:ddc2" removed.
(II) RADEON(0): I2C device "DVI_DDC:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "DVI_DDC:ddc2" removed.
(II) RADEON(0): DDC Type: 2, Detected Monitor Type: 0
(II) RADEON(0): Detected Monitor Type: 0
finished output detect: 1
(II) RADEON(0): I2C device "GPIO_DDC:ddc2" registered at address 0xA0.
(II) RADEON(0): DDC Type: 6, Detected Monitor Type: 2
(II) RADEON(0): EDID data from the display on connector: Proprietary/LVDS ----------------------
(II) RADEON(0): Manufacturer: SEC Model: 3158 Serial#: 0
(II) RADEON(0): Year: 2003 Week: 0
(II) RADEON(0): EDID Version: 1.3
(II) RADEON(0): Digital Display Input
(II) RADEON(0): Max H-Image Size [cm]: horiz.: 33 vert.: 21
(II) RADEON(0): Gamma: 2.20
(II) RADEON(0): No DPMS capabilities specified; RGB/Color Display
(II) RADEON(0): First detailed timing is preferred mode
(II) RADEON(0): redX: 0.580 redY: 0.340 greenX: 0.310 greenY: 0.550
(II) RADEON(0): blueX: 0.155 blueY: 0.155 whiteX: 0.313 whiteY: 0.329
(II) RADEON(0): Manufacturer's mask: 0
(II) RADEON(0): Supported additional Video Mode:
(II) RADEON(0): clock: 71.2 MHz Image Size: 331 x 207 mm
(II) RADEON(0): h_active: 1280 h_sync: 1328 h_sync_end 1360 h_blank_end 1440 h_border: 0
(II) RADEON(0): v_active: 800 v_sync: 802 v_sync_end 808 v_blanking: 823 v_border: 0
(II) RADEON(0): Y0316154X1
(II) RADEON(0): ůr`@
(II) RADEON(0): EDID (in hex):
(II) RADEON(0): 00ffffffffffff004ca3583100000000
(II) RADEON(0): 000d0103802115780a87f594574f8c27
(II) RADEON(0): 27505400000001010101010101010101
(II) RADEON(0): 010101010101d51b00a0502017303020
(II) RADEON(0): 26004bcf100000190000000f00000000
(II) RADEON(0): 00000000002387026400000000fe0059
(II) RADEON(0): 303331360731353458310a20000000fe
(II) RADEON(0): 00c5af9e8e72604000010a2020200052
finished output detect: 2
finished output detect: 3
finished all detect
before xf86InitialConfiguration
(II) RADEON(0): I2C device "VGA_DDC:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "VGA_DDC:ddc2" removed.
(II) RADEON(0): I2C device "VGA_DDC:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "VGA_DDC:ddc2" removed.
(II) RADEON(0): I2C device "VGA_DDC:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "VGA_DDC:ddc2" removed.
(II) RADEON(0): DDC Type: 3, Detected Monitor Type: 0
(II) RADEON(0): I2C device "DVI_DDC:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "DVI_DDC:ddc2" removed.
(II) RADEON(0): I2C device "DVI_DDC:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "DVI_DDC:ddc2" removed.
(II) RADEON(0): I2C device "DVI_DDC:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "DVI_DDC:ddc2" removed.
(II) RADEON(0): DDC Type: 2, Detected Monitor Type: 0
(II) RADEON(0): Detected Monitor Type: 0
(II) RADEON(0): DDC Type: 6, Detected Monitor Type: 2
(II) RADEON(0): EDID data from the display on connector: Proprietary/LVDS ----------------------
(II) RADEON(0): Manufacturer: SEC Model: 3158 Serial#: 0
(II) RADEON(0): Year: 2003 Week: 0
(II) RADEON(0): EDID Version: 1.3
(II) RADEON(0): Digital Display Input
(II) RADEON(0): Max H-Image Size [cm]: horiz.: 33 vert.: 21
(II) RADEON(0): Gamma: 2.20
(II) RADEON(0): No DPMS capabilities specified; RGB/Color Display
(II) RADEON(0): First detailed timing is preferred mode
(II) RADEON(0): redX: 0.580 redY: 0.340 greenX: 0.310 greenY: 0.550
(II) RADEON(0): blueX: 0.155 blueY: 0.155 whiteX: 0.313 whiteY: 0.329
(II) RADEON(0): Manufacturer's mask: 0
(II) RADEON(0): Supported additional Video Mode:
(II) RADEON(0): clock: 71.2 MHz Image Size: 331 x 207 mm
(II) RADEON(0): h_active: 1280 h_sync: 1328 h_sync_end 1360 h_blank_end 1440 h_border: 0
(II) RADEON(0): v_active: 800 v_sync: 802 v_sync_end 808 v_blanking: 823 v_border: 0
(II) RADEON(0): Y0316154X1
(II) RADEON(0): ůr`@
(II) RADEON(0): EDID (in hex):
(II) RADEON(0): 00ffffffffffff004ca3583100000000
(II) RADEON(0): 000d0103802115780a87f594574f8c27
(II) RADEON(0): 27505400000001010101010101010101
(II) RADEON(0): 010101010101d51b00a0502017303020
(II) RADEON(0): 26004bcf100000190000000f00000000
(II) RADEON(0): 00000000002387026400000000fe0059
(II) RADEON(0): 303331360731353458310a20000000fe
(II) RADEON(0): 00c5af9e8e72604000010a2020200052
in RADEONProbeOutputModes
(II) RADEON(0): EDID vendor "SEC", prod id 12632
(II) RADEON(0): Output VGA-0 disconnected
(II) RADEON(0): Output DVI-0 disconnected
(II) RADEON(0): Output LVDS connected
(II) RADEON(0): Output S-video disconnected
(II) RADEON(0): Output LVDS using initial mode 1280x800
after xf86InitialConfiguration
(==) RADEON(0): DPI set to (96, 96)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.4.0, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.3
(==) RADEON(0): Using gamma correction (1.0, 1.0, 1.0)
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"(II) Module "ramdac" already built-in
(==) RADEON(0): Using XAA acceleration architecture
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/lib/xorg/modules//libxaa.so
(II) Module xaa: vendor="X.Org Foundation"
compiled for 1.4.0, module version = 1.2.0
ABI class: X.Org Video Driver, version 2.0
(==) RADEON(0): Assuming overlay scaler buffer width is 1920
(II) RADEON(0): No MM_TABLE found - assuming CARD is not TV-in capable.
(!!) RADEON(0): For information on using the multimedia capabilities
of this adapter, please see http://gatos.sf.net.
(!!) RADEON(0): MergedFB support has been removed and replaced with xrandr 1.2 support
(--) Depth 24 pixmap format is 32 bpp
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] 0 0 0xfcff0000 - 0xfcffffff (0x10000) MX[b]
[1] 0 0 0xd0000000 - 0xdfffffff (0x10000000) MX[b]
[2] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[3] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[4] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[5] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[6] -1 0 0xfaffc000 - 0xfaffcfff (0x1000) MX[b]
[7] -1 0 0xfaff8000 - 0xfaffbfff (0x4000) MX[b]
[8] -1 0 0xfaffd800 - 0xfaffdfff (0x800) MX[b]
[9] -1 0 0xfaffe000 - 0xfaffffff (0x2000) MX[b]
[10] -1 0 0xf4fff400 - 0xf4fff4ff (0x100) MX[b]
[11] -1 0 0xf4fff800 - 0xf4fff9ff (0x200) MX[b]
[12] -1 0 0x44000000 - 0x440003ff (0x400) MX[b]
[13] -1 0 0xf4fffc00 - 0xf4ffffff (0x400) MX[b]
[14] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
[15] -1 0 0xfc000000 - 0xfc01ffff (0x20000) MX[b](B)
[16] -1 0 0xfcff0000 - 0xfcffffff (0x10000) MX[b](B)
[17] -1 0 0xd0000000 - 0xdfffffff (0x10000000) MX[b](B)
[18] 0 0 0x000a0000 - 0x000affff (0x10000) MS[b](OprU)
[19] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[b](OprU)
[20] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[b](OprU)
[21] 0 0 0x0000c000 - 0x0000c0ff (0x100) IX[b]
[22] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[23] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[24] -1 0 0x0000b080 - 0x0000b0ff (0x80) IX[b]
[25] -1 0 0x0000b400 - 0x0000b4ff (0x100) IX[b]
[26] -1 0 0x0000bc40 - 0x0000bc7f (0x40) IX[b]
[27] -1 0 0x0000b800 - 0x0000b8ff (0x100) IX[b]
[28] -1 0 0x0000bfa0 - 0x0000bfaf (0x10) IX[b]
[29] -1 0 0x00000374 - 0x00000374 (0x1) IX[b]
[30] -1 0 0x00000170 - 0x00000177 (0x8) IX[b]
[31] -1 0 0x000003f4 - 0x000003f4 (0x1) IX[b]
[32] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[33] -1 0 0x0000bf20 - 0x0000bf3f (0x20) IX[b]
[34] -1 0 0x0000bf40 - 0x0000bf5f (0x20) IX[b]
[35] -1 0 0x0000bf80 - 0x0000bf9f (0x20) IX[b]
[36] -1 0 0x0000c000 - 0x0000c0ff (0x100) IX[b](B)
[37] 0 0 0x000003b0 - 0x000003bb (0xc) IS[b](OprU)
[38] 0 0 0x000003c0 - 0x000003df (0x20) IS[b](OprU)
(==) RADEON(0): Write-combining range (0xd0000000,0x8000000)
Entering TV Save
Save TV timing tables
saveTimingTables: reading timing tables
TV Save done
(II) RADEON(0): Dynamic Clock Scaling Disabled
(==) RADEON(0): Using 24 bit depth buffer
(II) RADEON(0): RADEONInitMemoryMap() :
(II) RADEON(0): mem_size : 0x08000000
(II) RADEON(0): MC_FB_LOCATION : 0xd7ffd000
(II) RADEON(0): MC_AGP_LOCATION : 0xffffffc0
(II) RADEON(0): Depth moves disabled by default
(II) RADEON(0): CP in BM mode
(II) RADEON(0): Using 8 MB GART aperture
(II) RADEON(0): Using 1 MB for the ring buffer
(II) RADEON(0): Using 2 MB for vertex/indirect buffers
(II) RADEON(0): Using 5 MB for GART textures
(II) RADEON(0): Memory manager initialized to (0,0) (1280,8191)
(II) RADEON(0): Reserved area from (0,1200) to (1280,1202)
(II) RADEON(0): Largest offscreen area available: 1280 x 6989
(II) RADEON(0): Will use front buffer at offset 0x0
(II) RADEON(0): Will use back buffer at offset 0x1838000
(II) RADEON(0): Will use depth buffer at offset 0x1e14000
(II) RADEON(0): Will use 94208 kb for textures at offset 0x23f0000
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 9, (OK)
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 9, (OK)
drmOpenByBusid: Searching for BusID pci:0000:01:00.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 9, (OK)
drmOpenByBusid: drmOpenMinor returns 9
drmOpenByBusid: drmGetBusid reports pci:0000:01:00.0
(II) [drm] DRM interface version 1.3
(II) [drm] DRM open master succeeded.
(II) RADEON(0): [drm] Using the DRM lock SAREA also for drawables.
(II) RADEON(0): [drm] framebuffer handle = 0xd0000000
(II) RADEON(0): [drm] added 1 reserved context for kernel
(II) RADEON(0): X context handle = 0x1
(II) RADEON(0): [drm] installed DRM signal handler
(==) RADEON(0): Using AGP 4x
(II) RADEON(0): [agp] Mode 0x1f000207 [AGP 0x8086/0x3340; Card 0x1002/0x4e50]
(II) RADEON(0): [agp] 8192 kB allocated with handle 0x00000001
(II) RADEON(0): [agp] ring handle = 0xe0000000
(II) RADEON(0): [agp] Ring mapped at 0xaf920000
(II) RADEON(0): [agp] ring read ptr handle = 0xe0101000
(II) RADEON(0): [agp] Ring read ptr mapped at 0xaf91f000
(II) RADEON(0): [agp] vertex/indirect buffers handle = 0xe0102000
(II) RADEON(0): [agp] Vertex/indirect buffers mapped at 0xaf71f000
(II) RADEON(0): [agp] GART texture map handle = 0xe0302000
(II) RADEON(0): [agp] GART Texture map mapped at 0xaf23f000
(II) RADEON(0): [drm] register handle = 0xfcff0000
(II) RADEON(0): [dri] Visual configs initialized
init memmap
init common
init crtc1
init pll1
restore memmap
(II) RADEON(0): RADEONRestoreMemMapRegisters() :
(II) RADEON(0): MC_FB_LOCATION : 0xd7ffd000
(II) RADEON(0): MC_AGP_LOCATION : 0xffffffc0
restore common
restore crtc1
restore pll1
restore LVDS
enable montype: 2
(WW) RADEON(0): No crtc mode list for crtc 1,continuing with desired mode
disable montype: 2
(==) RADEON(0): Backing store disabled
(II) RADEON(0): [DRI] installation complete
(II) RADEON(0): [drm] Added 32 65536 byte vertex/indirect buffers
(II) RADEON(0): [drm] Mapped 32 vertex/indirect buffers
(II) RADEON(0): [drm] dma control initialized, using IRQ 11
(II) RADEON(0): [drm] Initialized kernel GART heap manager, 5111808
(WW) RADEON(0): DRI init changed memory map, adjusting ...
(WW) RADEON(0): MC_FB_LOCATION was: 0xd7ffd000 is: 0xd7ffd000
(WW) RADEON(0): MC_AGP_LOCATION was: 0xffffffc0 is: 0xe07fe000
(II) RADEON(0): RADEONRestoreMemMapRegisters() :
(II) RADEON(0): MC_FB_LOCATION : 0xd7ffd000
(II) RADEON(0): MC_AGP_LOCATION : 0xe07fe000
(II) RADEON(0): Direct rendering enabled
(II) RADEON(0): Render acceleration unsupported on Radeon 9500/9700 and newer.
(II) RADEON(0): Render acceleration disabled
(II) RADEON(0): Using XFree86 Acceleration Architecture (XAA)
Screen to screen bit blits
Solid filled rectangles
8x8 mono pattern filled rectangles
Indirect CPU to Screen color expansion
Solid Lines
Scanline Image Writes
Offscreen Pixmaps
Setting up tile and stipple cache:
32 128x128 slots
32 256x256 slots
16 512x512 slots
(II) RADEON(0): Acceleration enabled
(==) RADEON(0): Silken mouse enabled
(II) RADEON(0): Using hardware cursor (scanline 1202)
(II) RADEON(0): Largest offscreen area available: 1280 x 6985
(II) RADEON(0): No video input capabilities detected and no information is provided - disabling multimedia i2c
(II) Loading sub module "theatre_detect"
(II) LoadModule: "theatre_detect"
(II) Loading /usr/lib/xorg/modules/multimedia//theatre_detect_drv.so
(II) Module theatre_detect: vendor="X.Org Foundation"
compiled for 1.4.0, module version = 1.0.0
ABI class: X.Org Video Driver, version 2.0
(II) RADEON(0): no multimedia table present, disabling Rage Theatre.
(II) RADEON(0): RandR 1.2 enabled, ignore the following RandR disabled message.
(--) RandR disabled
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension XAccessControlExtension
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension XFree86-Bigfont
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing built-in extension XEVIE
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 10, (OK)
drmOpenByBusid: Searching for BusID pci:0000:01:00.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 10, (OK)
drmOpenByBusid: drmOpenMinor returns 10
drmOpenByBusid: drmGetBusid reports pci:0000:01:00.0
(WW) AIGLX: 3D driver claims to not support visual 0x23
(WW) AIGLX: 3D driver claims to not support visual 0x24
(WW) AIGLX: 3D driver claims to not support visual 0x25
(WW) AIGLX: 3D driver claims to not support visual 0x26
(WW) AIGLX: 3D driver claims to not support visual 0x27
(WW) AIGLX: 3D driver claims to not support visual 0x28
(WW) AIGLX: 3D driver claims to not support visual 0x29
(WW) AIGLX: 3D driver claims to not support visual 0x2a
(WW) AIGLX: 3D driver claims to not support visual 0x2b
(WW) AIGLX: 3D driver claims to not support visual 0x2c
(WW) AIGLX: 3D driver claims to not support visual 0x2d
(WW) AIGLX: 3D driver claims to not support visual 0x2e
(WW) AIGLX: 3D driver claims to not support visual 0x2f
(WW) AIGLX: 3D driver claims to not support visual 0x30
(WW) AIGLX: 3D driver claims to not support visual 0x31
(WW) AIGLX: 3D driver claims to not support visual 0x32
(II) AIGLX: Loaded and initialized /usr/lib/xorg/modules/dri/r300_dri.so
(II) GLX: Initialized DRI GL provider for screen 0
(II) RADEON(0): Setting screen physical size to 331 x 207
(II) Synaptics touchpad driver version 0.14.6 (1406)
(--) Alps touchpad auto-dev sets device to /dev/input/event6
(**) Option "Device" "/dev/input/event6"
(**) Option "SHMConfig" "on"
(**) Option "LeftEdge" "1700"
(**) Option "RightEdge" "5300"
(**) Option "TopEdge" "1700"
(**) Option "BottomEdge" "4200"
(**) Option "VertScrollDelta" "100"
(**) Option "FingerLow" "25"
(**) Option "FingerHigh" "30"
(**) Option "MaxTapTime" "180"
(**) Option "MaxTapMove" "220"
(--) Alps touchpad touchpad found
(**) Option "CorePointer"
(**) Alps touchpad: always reports core events
(**) Option "CoreKeyboard"
(**) Keyboard0: always reports core events
(**) Option "Protocol" "standard"
(**) Keyboard0: Protocol: standard
(**) Option "AutoRepeat" "500 30"
(**) Option "XkbRules" "xorg"
(**) Keyboard0: XkbRules: "xorg"
(**) Option "XkbModel" "pc105"
(**) Keyboard0: XkbModel: "pc105"
(**) Option "XkbLayout" "us"
(**) Keyboard0: XkbLayout: "us"
(**) Option "CustomKeycodes" "off"
(**) Keyboard0: CustomKeycodes disabled
(WW) <default pointer>: No Device specified, looking for one...
(II) <default pointer>: Setting Device option to "/dev/input/mice"
(--) <default pointer>: Device: "/dev/input/mice"
(==) <default pointer>: Protocol: "Auto"
(**) Option "AlwaysCore"
(**) <default pointer>: doesn't report core events
(==) <default pointer>: Emulate3Buttons, Emulate3Timeout: 50
(**) <default pointer>: ZAxisMapping: buttons 4 and 5
(**) <default pointer>: Buttons: 9
(**) <default pointer>: Sensitivity: 1
(II) evaluating device (<default pointer>)
(II) XINPUT: Adding extended input device "<default pointer>" (type: MOUSE)
(II) evaluating device (Keyboard0)
(II) XINPUT: Adding extended input device "Keyboard0" (type: KEYBOARD)
(II) evaluating device (Alps touchpad)
(II) XINPUT: Adding extended input device "Alps touchpad" (type: MOUSE)
(--) <default pointer>: PnP-detected protocol: "ExplorerPS/2"
(II) <default pointer>: ps2EnableDataReporting: succeeded
(--) Alps touchpad auto-dev sets device to /dev/input/event6
(**) Option "Device" "/dev/input/event6"
(--) Alps touchpad touchpad foundand here's my entire Xorg.conf file. You will see that I have been playing with it some... with little/no success. Due to viewing the log I saw "Alps touchpad sets device to /dev/input/event6" so I tried changing my device to that with the same result, no scroll.
[shane@Shane-Arch ~]$ cat /etc/X11/xorg.conf
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Alps touchpad" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
RgbPath "/usr/share/X11/rgb"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/misc"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/75dpi:unscaled"
FontPath "/usr/share/fonts/TTF"
FontPath "/usr/share/fonts/Type1"
EndSection
Section "Module"
Load "dbe"
Load "record"
Load "dri"
Load "extmod"
Load "xtrap"
Load "type1"
Load "freetype"
Load "synaptics"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
EndSection
##
#MOUSE
##
Section "InputDevice"
Identifier "Generic Mouse"
Driver "mouse"
Option "Protocol" "Auto" # Auto detect
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5 6 7"
Option "Emulate3Buttons"
EndSection
Section "InputDevice"
Driver "synaptics"
Identifier "Alps touchpad"
Option "Device" "/dev/input/event6"
Option "Protocol" "auto-dev"
Option "Emulate3Buttons"
# synaptic driver specific options
Option "LeftEdge" "1700"
Option "RightEdge" "5300"
Option "TopEdge" "1700"
Option "BottomEdge" "4200"
Option "FingerLow" "25"
Option "FingerHigh" "30"
Option "MaxTapTime" "180"
Option "MaxTapMove" "220"
Option "VertScrollDelta" "100"
Option "MinSpeed" "0.24"
Option "MaxSpeed" "0.48"
Option "AccelFactor" "0.01"
Option "SHMConfig" "on"
EndSection
#Section "InputDevice"
# Identifier "Touchpad"
# Driver "synaptics"
# Option "Device" "/dev/input/mouse0"
# Option "Protocol" "auto-dev"
# Option "LeftEdge" "1700"
# Option "RightEdge" "5300"
# Option "TopEdge" "1700"
# Option "BottomEdge" "4200"
# Option "FingerLow" "25"
# Option "FingerHigh" "30"
# Option "MaxTapTime" "180"
# Option "MaxTapMove" "220"
# Option "VertScrollDelta" "100"
# Option "MinSpeed" "0.24"
# Option "MaxSpeed" "0.48"
# Option "AccelFactor" "0.0100"
# Option "SHMConfig" "on"
# Option "SendCoreEvents" "true"
#EndSection
#Section "InputDevice"
# Identifier "Mouse0"
# Driver "mouse"
# Option "Protocol" "auto"
# Option "Device" "/dev/input/mice"
# Option "ZAxisMapping" "4 5 6 7"
#EndSection
Section "Monitor"
#DisplaySize 330 210 # mm
Identifier "Monitor0"
VendorName "SEC"
ModelName "3158"
EndSection
Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
### [arg]: arg optional
#Option "NoAccel" # [<bool>]
#Option "SWcursor" # [<bool>]
#Option "Dac6Bit" # [<bool>]
#Option "Dac8Bit" # [<bool>]
#Option "BusType" # [<str>]
#Option "CPPIOMode" # [<bool>]
#Option "CPusecTimeout" # <i>
#Option "AGPMode" # <i>
#Option "AGPFastWrite" # [<bool>]
#Option "AGPSize" # <i>
#Option "GARTSize" # <i>
#Option "RingSize" # <i>
#Option "BufferSize" # <i>
#Option "EnableDepthMoves" # [<bool>]
#Option "EnablePageFlip" # [<bool>]
#Option "NoBackBuffer" # [<bool>]
#Option "DMAForXv" # [<bool>]
#Option "FBTexPercent" # <i>
#Option "DepthBits" # <i>
#Option "PCIAPERSize" # <i>
#Option "AccelDFS" # [<bool>]
#Option "DDCMode" # [<bool>]
#Option "IgnoreEDID" # [<bool>]
#Option "DisplayPriority" # [<str>]
#Option "PanelSize" # [<str>]
#Option "ForceMinDotClock" # <freq>
#Option "ColorTiling" # [<bool>]
#Option "VideoKey" # <i>
#Option "RageTheatreCrystal" # <i>
#Option "RageTheatreTunerPort" # <i>
#Option "RageTheatreCompositePort" # <i>
#Option "RageTheatreSVideoPort" # <i>
#Option "TunerType" # <i>
#Option "RageTheatreMicrocPath" # <str>
#Option "RageTheatreMicrocType" # <str>
#Option "ScalerWidth" # <i>
#Option "RenderAccel" # [<bool>]
#Option "SubPixelOrder" # [<str>]
#Option "ShowCache" # [<bool>]
#Option "DynamicClocks" # [<bool>]
#Option "VGAAccess" # [<bool>]
#Option "ReverseDDC" # [<bool>]
#Option "LVDSProbePLL" # [<bool>]
#Option "AccelMethod" # <str>
#Option "DRI" # [<bool>]
#Option "ConnectorTable" # <str>
#Option "DefaultConnectorTable" # [<bool>]
#Option "DefaultTMDSPLL" # [<bool>]
#Option "LVDSBiosNativeMode" # [<bool>]
Identifier "Card0"
Driver "ati"
VendorName "ATI Technologies Inc"
BoardName "RV350 [Mobility Radeon 9600 M10]"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
SubSection "Display"
Viewport 0 0
Depth 1
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 4
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 8
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 15
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSectionSee anything wrong?
Thanks again for all the help.
-Shane
Offline
#7 2007-12-03 18:02:49
- SiD
- Member
- From: Germany
- Registered: 2006-09-21
- Posts: 729
Re: [solved] Synaptics touchpad scrolling not working...
The config for ALPS Pads is different from the one for SYNAPTICS Pads.
Found in the German Wiki.
Section "InputDevice"
Identifier "Touchpad"
Driver "synaptics"
Option "Device" "/dev/input/mouse0"
Option "SendCoreEvents" "true"
Option "Protocol" "auto-dev"
Option "LeftEdge" "130"
Option "RightEdge" "840"
Option "TopEdge" "130"
Option "BottomEdge" "640"
Option "FingerLow" "7"
Option "FingerHigh" "8"
Option "MaxTapTime" "180"
Option "MaxTapMove" "110"
Option "EmulateMidButtonTime" "75"
Option "VertScrollDelta" "20"
Option "HorizScrollDelta" "20"
Option "MinSpeed" "0.60"
Option "MaxSpeed" "1.10"
Option "AccelFactor" "0.030"
Option "EdgeMotionMinSpeed" "200"
Option "EdgeMotionMaxSpeed" "200"
Option "UpDownScrolling" "1"
Option "CircularScrolling" "1"
Option "CircScrollDelta" "0.1"
Option "CircScrollTrigger" "2"
Option "SHMConfig" "on"
Option "Emulate3Buttons" "on"
EndSectionMaybe this helps ...
Last edited by SiD (2007-12-03 18:05:26)
Offline
#8 2007-12-03 18:11:27
- sjb933
- Member
- Registered: 2007-01-18
- Posts: 113
Re: [solved] Synaptics touchpad scrolling not working...
Woo! I got it 
I am also going to update the Synaptics wiki page with my config for an ALPS touchpad. Here is my new xorg.conf file:
[shane@Shane-Arch ~]$ cat /etc/X11/xorg.conf
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse" "CorePointer"
InputDevice "Touchpad" "SendCoreEvents"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
RgbPath "/usr/share/X11/rgb"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/misc"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/75dpi:unscaled"
FontPath "/usr/share/fonts/TTF"
FontPath "/usr/share/fonts/Type1"
EndSection
Section "Module"
Load "dbe"
Load "record"
Load "dri"
Load "extmod"
Load "xtrap"
Load "type1"
Load "freetype"
Load "synaptics"
EndSection
############
# Keyboard #
############
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
EndSection
##################
# Mouse/Touchpad #
##################
Section "InputDevice"
Identifier "Mouse"
Driver "mouse"
Option "Protocol" "Auto" # Auto detect
Option "Device" "/dev/input/mouse1"
Option "ZAxisMapping" "4 5 6 7"
Option "Emulate3Buttons"
EndSection
Section "InputDevice"
Driver "synaptics"
Identifier "Touchpad"
Option "Device" "/dev/input/mouse2"
Option "Protocol" "auto-dev"
Option "LeftEdge" "130"
Option "RightEdge" "840"
Option "TopEdge" "130"
Option "BottomEdge" "640"
Option "FingerLow" "7"
Option "FingerHigh" "8"
Option "MaxTapTime" "180"
Option "MaxTapMove" "110"
Option "EmulateMidButtonTime" "75"
Option "VertScrollDelta" "20"
Option "HorizScrollDelta" "20"
Option "MinSpeed" "0.25"
Option "MaxSpeed" "0.50"
Option "AccelFactor" "0.010"
Option "EdgeMotionMinSpeed" "200"
Option "EdgeMotionMaxSpeed" "200"
Option "UpDownScrolling" "1"
Option "CircularScrolling" "1"
Option "CircScrollDelta" "0.1"
Option "CircScrollTrigger" "2"
Option "SHMConfig" "on"
#always usefull
Option "Emulate3Buttons" "on"
EndSection
Section "Monitor"
#DisplaySize 330 210 # mm
Identifier "Monitor0"
VendorName "SEC"
ModelName "3158"
EndSection
Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
### [arg]: arg optional
#Option "NoAccel" # [<bool>]
#Option "SWcursor" # [<bool>]
#Option "Dac6Bit" # [<bool>]
#Option "Dac8Bit" # [<bool>]
#Option "BusType" # [<str>]
#Option "CPPIOMode" # [<bool>]
#Option "CPusecTimeout" # <i>
#Option "AGPMode" # <i>
#Option "AGPFastWrite" # [<bool>]
#Option "AGPSize" # <i>
#Option "GARTSize" # <i>
#Option "RingSize" # <i>
#Option "BufferSize" # <i>
#Option "EnableDepthMoves" # [<bool>]
#Option "EnablePageFlip" # [<bool>]
#Option "NoBackBuffer" # [<bool>]
#Option "DMAForXv" # [<bool>]
#Option "FBTexPercent" # <i>
#Option "DepthBits" # <i>
#Option "PCIAPERSize" # <i>
#Option "AccelDFS" # [<bool>]
#Option "DDCMode" # [<bool>]
#Option "IgnoreEDID" # [<bool>]
#Option "DisplayPriority" # [<str>]
#Option "PanelSize" # [<str>]
#Option "ForceMinDotClock" # <freq>
#Option "ColorTiling" # [<bool>]
#Option "VideoKey" # <i>
#Option "RageTheatreCrystal" # <i>
#Option "RageTheatreTunerPort" # <i>
#Option "RageTheatreCompositePort" # <i>
#Option "RageTheatreSVideoPort" # <i>
#Option "TunerType" # <i>
#Option "RageTheatreMicrocPath" # <str>
#Option "RageTheatreMicrocType" # <str>
#Option "ScalerWidth" # <i>
#Option "RenderAccel" # [<bool>]
#Option "SubPixelOrder" # [<str>]
#Option "ShowCache" # [<bool>]
#Option "DynamicClocks" # [<bool>]
#Option "VGAAccess" # [<bool>]
#Option "ReverseDDC" # [<bool>]
#Option "LVDSProbePLL" # [<bool>]
#Option "AccelMethod" # <str>
#Option "DRI" # [<bool>]
#Option "ConnectorTable" # <str>
#Option "DefaultConnectorTable" # [<bool>]
#Option "DefaultTMDSPLL" # [<bool>]
#Option "LVDSBiosNativeMode" # [<bool>]
Identifier "Card0"
Driver "ati"
VendorName "ATI Technologies Inc"
BoardName "RV350 [Mobility Radeon 9600 M10]"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
SubSection "Display"
Viewport 0 0
Depth 1
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 4
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 8
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 15
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSectionThanks for the help everyone.
-Shane
Offline
#9 2007-12-03 18:12:15
- sjb933
- Member
- Registered: 2007-01-18
- Posts: 113
Re: [solved] Synaptics touchpad scrolling not working...
SiD wrote:
The config for ALPS Pads is different from the one for SYNAPTICS Pads.
Found in the German Wiki.Section "InputDevice" Identifier "Touchpad" Driver "synaptics" Option "Device" "/dev/input/mouse0" Option "SendCoreEvents" "true" Option "Protocol" "auto-dev" Option "LeftEdge" "130" Option "RightEdge" "840" Option "TopEdge" "130" Option "BottomEdge" "640" Option "FingerLow" "7" Option "FingerHigh" "8" Option "MaxTapTime" "180" Option "MaxTapMove" "110" Option "EmulateMidButtonTime" "75" Option "VertScrollDelta" "20" Option "HorizScrollDelta" "20" Option "MinSpeed" "0.60" Option "MaxSpeed" "1.10" Option "AccelFactor" "0.030" Option "EdgeMotionMinSpeed" "200" Option "EdgeMotionMaxSpeed" "200" Option "UpDownScrolling" "1" Option "CircularScrolling" "1" Option "CircScrollDelta" "0.1" Option "CircScrollTrigger" "2" Option "SHMConfig" "on" Option "Emulate3Buttons" "on" EndSectionMaybe this helps ...
Yep 
I had just found these settings on a gentoo wiki page specifically for ALPS.
Offline
#10 2007-12-03 18:23:22
- sjb933
- Member
- Registered: 2007-01-18
- Posts: 113
Re: [solved] Synaptics touchpad scrolling not working...
Mmk. I've updated the wiki.
Offline