You are not logged in.

Pages: 1

#1 2008-01-18 20:12:13

k3rn31
Member
Registered: 2008-01-09
Posts: 145

My Archie boot is very slow on my laptop

Hi guys. I have a serious problem cause my boot time is about 3 minutes. I think that something happened with ata02 but I am not sure. What I must do to check where is the problem and to fix it?

My demesg is:

Linux version 2.6.23-ARCH (root@T-POWA-LX) (gcc version 4.2.2) #1 SMP PREEMPT Tue Jan 15 06:34:36 UTC 2008
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001fef0000 (usable)
 BIOS-e820: 000000001fef0000 - 000000001feff000 (ACPI data)
 BIOS-e820: 000000001feff000 - 000000001ff00000 (ACPI NVS)
 BIOS-e820: 000000001ff00000 - 0000000020000000 (reserved)
 BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
510MB LOWMEM available.
Entering add_active_range(0, 0, 130800) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   130800
  HighMem    130800 ->   130800
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->   130800
On node 0 totalpages: 130800
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 989 pages used for memmap
  Normal zone: 125715 pages, LIFO batch:31
  HighMem zone: 0 pages used for memmap
  Movable zone: 0 pages used for memmap
DMI present.
ACPI: RSDP 000F6EB0, 0014 (r0 PTLTD )
ACPI: RSDT 1FEF5E29, 002C (r1 PTLTD  EGRSDT    2330000  LTP        0)
ACPI: FACP 1FEFEF64, 0074 (r1 ALI    EG533     2330000 PTL     F4240)
ACPI: DSDT 1FEF5E55, 910F (r1    ALI    EG533  2330000 MSFT  100000D)
ACPI: FACS 1FEFFFC0, 0040
ACPI: BOOT 1FEFEFD8, 0028 (r1 PTLTD  EGBFTBL$  2330000  LTP        1)
ACPI: PM-Timer IO Port: 0x8008
Allocating PCI resources starting at 30000000 (gap: 20000000:dffc0000)
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e0000
swsusp: Registered nosave memory region: 00000000000e0000 - 0000000000100000
Built 1 zonelists in Zone order.  Total pages: 129779
Kernel command line: root=/dev/sda4 ro
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffb000 (0140e000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 1599.995 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 512340k/523200k available (2444k kernel code, 10332k reserved, 818k data, 296k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xfff80000 - 0xfffff000   ( 508 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xe0800000 - 0xff7fe000   ( 495 MB)
    lowmem  : 0xc0000000 - 0xdfef0000   ( 510 MB)
      .init : 0xc0435000 - 0xc047f000   ( 296 kB)
      .data : 0xc03630c9 - 0xc042f99c   ( 818 kB)
      .text : 0xc0100000 - 0xc03630c9   (2444 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Calibrating delay using timer specific routine.. 3204.39 BogoMIPS (lpj=5338229)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 3febf9ff 00000000 00000000 00000000 00000000 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Hyper-Threading is disabled
CPU: After all inits, caps: 3febf9ff 00000000 00000000 0000b080 00000000 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 11k freed
Early unpacking initramfs... done
ACPI: Core revision 20070126
ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
ACPI: setting ELCR to 0200 (from 0400)
CPU0: Intel(R) Pentium(R) 4 Mobile CPU 1.60GHz stepping 04
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd88b, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: EC: GPE = 0x18, I/O: command/status = 0x66, data = 0x62
ACPI: EC: acpi_ec_wait timeout, status = 10, expect_event = 2
ACPI: EC: write_cmd timeout, command = 128
ACPI Exception (evregion-0420): AE_TIME, Returned by Handler for [EmbeddedControl] [20070126]
ACPI Exception (dswexec-0462): AE_TIME, While resolving operands for [OpcodeName unavailable] [20070126]
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.ISA_.EC0_.MBAY] (Node c17c9d50), AE_TIME
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._INI] (Node c17c2690), AE_TIME
ACPI: EC: acpi_ec_wait timeout, status = 10, expect_event = 2
ACPI: EC: input buffer is not empty, aborting transaction
ACPI Exception (evregion-0420): AE_TIME, Returned by Handler for [EmbeddedControl] [20070126]
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.ISA_.SIO_.FDC_._INI] (Node c17c6a80), AE_TIME
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using PIC for interrupt routing
ACPI: EC: GPE = 0x18, I/O: command/status = 0x66, data = 0x62
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI quirk: region 8000-803f claimed by ali7101 ACPI
PCI quirk: region 8040-805f claimed by ali7101 SMB
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 11 12) *10
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *10 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 10 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 6 7 10 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 11 12) *7
ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 6 7 *10 12)
ACPI: Power Resource [PFNL] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
ACPI: RTC can wake from S4
Time: tsc clocksource has been installed.
pnp: 00:07: ioport range 0x3810-0x381f has been reserved
pnp: 00:07: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:07: ioport range 0x8000-0x805f could not be reserved
pnp: 00:07: ioport range 0x4d6-0x4d6 has been reserved
pnp: 00:07: iomem range 0xfffc0000-0xffffffff could not be reserved
pnp: 00:07: iomem range 0xfec00000-0xfec00fff has been reserved
PCI: Bridge: 0000:00:01.0
  IO window: 9000-9fff
  MEM window: e0100000-e01fffff
  PREFETCH window: e8000000-efffffff
PCI: Bus 2, cardbus bridge: 0000:00:0a.0
  IO window: 00001c00-00001cff
  IO window: 00002000-000020ff
  PREFETCH window: 30000000-33ffffff
  MEM window: 34000000-37ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 6, 262144 bytes)
TCP bind hash table entries: 16384 (order: 5, 196608 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 1767k freed
Simple Boot Flag at 0x38 set to 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Activating ISA DMA hang workarounds.
Boot video device is 0000:01:00.0
isapnp: Scanning for PnP cards...
Switched to high resolution mode on CPU 0
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input0
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
Freeing unused kernel memory: 296k freed
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [LNKU] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKU] -> GSI 10 (level, low) -> IRQ 10
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 10, io mem 0xe0000000
libata version 2.21 loaded.
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: Unable to derive IRQ for device 0000:00:0f.0
ACPI: PCI Interrupt 0000:00:0f.0[A]: no GSI
scsi0 : pata_ali
scsi1 : pata_ali
ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00011810 irq 14
ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x00011818 irq 15
ata1.00: ATA-5: TOSHIBA MK3018GAP, M2.01 A, max UDMA/100
ata1.00: 58605120 sectors, multi 16: LBA 
ata1.00: limited to UDMA/33 due to 40-wire cable
ata1.00: configured for UDMA/33
usb 1-1: new low speed USB device using ohci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
ata2.00: ATAPI: MATSHITADVD-ROM SR-8176, M136, max UDMA/33
ata2.00: configured for UDMA/33
scsi 0:0:0:0: Direct-Access     ATA      TOSHIBA MK3018GA M2.0 PQ: 0 ANSI: 5
usbcore: registered new interface driver hiddev
input: Microsoft Microsoft 5-Button Mouse with IntelliEye(TM) as /devices/pci0000:00/0000:00:02.0/usb1/1-1/1-1:1.0/input/input2
input: USB HID v1.10 Mouse [Microsoft Microsoft 5-Button Mouse with IntelliEye(TM)] on usb-0000:00:02.0-1
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata2.00: cmd a0/01:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x12 data 96 in
         res 40/00:02:00:24:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata2: soft resetting port
ata2.00: configured for UDMA/33
ata2: EH complete
ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata2.00: cmd a0/01:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x12 data 96 in
         res 40/00:02:00:24:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata2: soft resetting port
ata2.00: configured for UDMA/33
ata2: EH complete
ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata2.00: cmd a0/01:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x12 data 96 in
         res 40/00:02:00:24:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata2: soft resetting port
ata2.00: configured for UDMA/33
ata2: EH complete
ata2.00: limiting speed to UDMA/25:PIO4
ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata2.00: cmd a0/01:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x12 data 96 in
         res 40/00:02:00:24:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata2: soft resetting port
ata2.00: configured for UDMA/25
ata2: EH complete
scsi scan: 96 byte inquiry failed.  Consider BLIST_INQUIRY_36 for this device
scsi 1:0:0:0: CD-ROM            MATSHITA DVD-ROM SR-8176  M136 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 58605120 512-byte hardware sectors (30006 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 58605120 512-byte hardware sectors (30006 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata2.00: cmd a0/01:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x5a data 128 in
         res 40/00:03:00:00:20/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata2: soft resetting port
ata2.00: configured for UDMA/25
ata2: EH complete
ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata2.00: cmd a0/01:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x5a data 128 in
         res 40/00:03:00:00:20/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata2: soft resetting port
ata2.00: configured for UDMA/25
ata2: EH complete
ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata2.00: cmd a0/01:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x5a data 128 in
         res 40/00:03:00:00:20/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata2: soft resetting port
ata2.00: configured for UDMA/25
ata2: EH complete
ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata2.00: cmd a0/01:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x5a data 128 in
         res 40/00:03:00:00:20/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata2: soft resetting port
ata2.00: configured for UDMA/25
ata2: EH complete
sr0: scsi-1 drive
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
8139cp 0000:00:08.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
8139cp 0000:00:08.0: Try the "8139too" driver instead.
8139too Fast Ethernet driver 0.9.28
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
eth0: RealTek RTL8139 at 0xe0822000, 00:c0:9f:0b:2e:07, IRQ 10
eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
Loaded prism54 driver, version 1.2
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
AC'97 1 does not respond - RESET
AC'97 1 access is not valid [0xffffffff], removing mixer.
ali mixer 1 creating error.
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Battery Slot [BAT2] (battery absent)
input: Power Button (FF) as /devices/virtual/input/input3
ACPI: Power Button (FF) [PWRF]
input: Sleep Button (CM) as /devices/virtual/input/input4
ACPI: Sleep Button (CM) [SLPB]
input: Power Button (CM) as /devices/virtual/input/input5
ACPI: Power Button (CM) [PWRB]
input: Lid Switch as /devices/virtual/input/input6
ACPI: Lid Switch [LID]
ACPI: Transitioning device [FAN2] to D3
ACPI: Transitioning device [FAN2] to D3
ACPI: Fan [FAN2] (off)
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Thermal Zone [THRM] (40 C)
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5
Linux agpgart interface v0.102
agpgart: Detected ALi M1671 chipset
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
agpgart: AGP aperture is 128M @ 0xf0000000
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Yenta: CardBus bridge found at 0000:00:0a.0 [103c:0027]
Yenta: adjusting diagnostic: 41 -> 61
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:0a.0, mfunc 0x015c1d22, devctl 0x66
Yenta: ISA IRQ mask 0x00b8, PCI irq 11
Socket status: 30000020
ali15x3_smbus 0000:00:06.0: ALI15X3_smb region uninitialized - upgrade BIOS or use force_addr=0xaddr
ali15x3_smbus 0000:00:06.0: ALI15X3 not detected, module not inserted.
Synaptics Touchpad, model: 1, fw: 5.8, id: 0x9b48b1, caps: 0x88479b/0x0
serio: Synaptics pass-through port at isa0060/serio1/input0
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input7
pccard: CardBus card inserted into slot 0
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k
input: PC Speaker as /devices/platform/pcspkr/input/input8
PPP generic driver version 2.4.2
input: PS/2 Generic Mouse as /devices/platform/i8042/serio1/serio2/input/input9
parport_pc 00:08: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
input: Video Bus as /devices/virtual/input/input10
ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
lp0: using parport0 (interrupt-driven).
cs: IO port probe 0x100-0x3af: excluding 0x200-0x207 0x220-0x22f 0x330-0x337 0x388-0x38f
cs: IO port probe 0x3e0-0x4ff: excluding 0x408-0x40f 0x480-0x48f
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
ppdev: user-space parallel port driver
Adding 1951888k swap on /dev/sda3.  Priority:-1 extents:1 across:1951888k
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
eth1: resetting device...
eth1: uploading firmware...
eth1: firmware version: 1.0.4.3
eth1: firmware upload complete
eth1: interface reset complete
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
[drm] Initialized radeon 1.28.0 20060524 on minor 0
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[drm] Setting GART location based on new memory map
[drm] writeback test succeeded in 1 usecs
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
eth0: no IPv6 routers present
eth1: no IPv6 routers present

My mkinitcpio.conf modules/hooks:

MODULES="piix ide_disk reiserfs"
HOOKS="base udev autodetect pata scsi sata usb usbinput keymap filesystems"

My Modules setting is not the normal, I have changed and I forgot the previous setting and I decided to enter the
default one but I think that is not correct for my system.

Also I tried in Modules these: 

MODULES="ata_generic ata_piix"

But the boot time is still too big.

My Laptop is a HP Omnibook.

Thanks smile

Last edited by k3rn31 (2008-01-19 09:30:02)

~k3rn31

Offline

#2 2008-01-20 09:35:29

k3rn31
Member
Registered: 2008-01-09
Posts: 145

Re: My Archie boot is very slow on my laptop

fixed with this method:
http://bbs.archlinux.org/viewtopic.php?pid=319710

~k3rn31

Offline

Pages: 1

Board footer

Powered by FluxBB