You are not logged in.
Using sony dru-530a, k3b in dvd iso setting, installed dvd+rw-tool.
Using memorex dvd+rw media.
Receive the following at start burn:k3b
System
-----------------------
K3b Version:0.11.10
KDE Version: 3.2.2
QT Version: 3.3.2
growisofs
-----------------------
Executing 'builtin_dd if=/root/knoppix-34-dvd-by-iso-top.info.iso of=/dev/ide/host0/bus1/target0/lun0/cd obs=32k seek=0'
:-( Failed to change write speed: 0->5540
growisofs comand:
-----------------------
/usr/bin/growisofs -Z /dev/ide/host0/bus1/target0/lun0/cd=/root/knoppix-34-dvd-by-iso-top.info.iso -use-the-force-luke=notray -use-the-force-luke=tty -speed=4
The following is fstab:
#
# /etc/fstab: static file system information
#
# <file system> <dir> <type> <options> <dump> <pass>
#/dev/#EXT2FS_BOOT# /boot ext2 defaults 0 1
#/dev/#REISERFS_ROOT# / reiserfs defaults 0 0
#/dev/#EXT2FS_ROOT# / ext2 defaults 0 1
#/dev/#SWAP# swap swap defaults 0 0
#/dev/#REISERFS_HOME# /home reiserfs defaults 0 0
#/dev/#EXT2FS_HOME# /home ext2 defaults 0 2
/dev/cdroms/cdrom1 /mnt/cd iso9660 ro,user,noauto,unhide 0 0
/dev/cdroms/cdrom0 /mnt/dvd udf rw,user,noauto,unhide 0 0
/dev/floppy/0 /mnt/fl vfat user,noauto,unhide 0 0
none /dev/pts devpts defaults 0 0
none /proc proc defaults 0 0
none /dev/shm tmpfs defaults 0 0
tmpfs /tmp tmpfs size=2G,nr_inodes=10k 0 0
/dev/discs/disc0/part3 / ext3 rw,users,exec 0 0
/dev/discs/disc0/part1 /boot ext2 defaults 0 1
/dev/discs/disc0/part2 swap swap defaults 0 0
/dev/discs/disc1/part3 /mnt/drive ext3 rw,users,exec 0 0
/dev/discs/disc1/part1 /mnt/fat1 vfat defaults 0 0
Just learning the ropes on DVD burning so am not familiar with the setups and not much in the forums .
Any help is appreciated.
Prediction...This year will be a very odd year!
Hard work does not kill people but why risk it: Charlie Mccarthy
A man is not complete until he is married..then..he is finished.
When ALL is lost, what can be found? Even bytes get lonely for a little bit! X-ray confirms Iam spineless!
Offline
http://fy.chalmers.se/~appro/linux/DVD+RW/
this will give you probably more than you need to know.
also i notice you have udf as the filetype for your dvd burner. i don't think that is necessary unless you have udf enabled in your kernel i usually just use the iso one that is used for the cdrom.
AKA uknowme
I am not your friend
Offline
Pleased to hear from you on this subject, and received the reference material which is quite extensive.
Be advised that I tried iso9660 first and the Dvd drive would not eject. It ejects in udf but I am sure now that udf is not enabled in the kernel. It seems it requires changes in addition to being enabled.
Don't have any idea why it won't eject in iso9660....
Prediction...This year will be a very odd year!
Hard work does not kill people but why risk it: Charlie Mccarthy
A man is not complete until he is married..then..he is finished.
When ALL is lost, what can be found? Even bytes get lonely for a little bit! X-ray confirms Iam spineless!
Offline
Problem has been solved, however weirdly!
I re-installed the DVD unit as an iso9660 and also used IGNORE in the write speed selection in k3b. It produced the 2.1 GB iso source very nicely on a dvd+rw disc.
It also booted the system into knoppix 3.4 (Kernel 2.4.25, cebit version).
I also copied the Knoppix LiveCD of 687MB (not the iso image) onto another dvd+rw so as to use the optional 2.6 kernel in that boot-up. I had to use IGNORE there also.
It boots OK as well.
Prediction...This year will be a very odd year!
Hard work does not kill people but why risk it: Charlie Mccarthy
A man is not complete until he is married..then..he is finished.
When ALL is lost, what can be found? Even bytes get lonely for a little bit! X-ray confirms Iam spineless!
Offline
great! good job. i hope that reference i posted helps you out in the future. i use dvd+rw-tools via the commandline but using k3b is just fine but at least youwill have a better understanding of options it uses should problems arise in the future.
good work on finding the solution!
AKA uknowme
I am not your friend
Offline