Arch Linux

riverscn

Member

From: Chongqing, China

Registered: 2008-08-05

Posts: 20

Website

portmap start fail

I got error message at system startup

:: Starting Portmap                                                      [FAIL]

How to solve this problem?
my /etc/rc.conf

#
# /etc/rc.conf - Main Configuration for Arch Linux
#

# -----------------------------------------------------------------------
# LOCALIZATION
# -----------------------------------------------------------------------
#
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# USEDIRECTISA: use direct I/O requests instead of /dev/rtc for hwclock
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
#
LOCALE="en_US.UTF8"
HARDWARECLOCK="localtime"
USEDIRECTISA="no"
TIMEZONE="Asia/Chongqing"
KEYMAP="us"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"

# -----------------------------------------------------------------------
# HARDWARE
# -----------------------------------------------------------------------
#
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
#
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
#
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
MODULES=(acpi-cpufreq cpufreq_ondemand cpufreq_powersave sky2 iwl3945 snd-mixer-oss snd-pcm-oss snd-hwdep snd-page-alloc snd-pcm snd-timer snd snd-hda-intel soundcore vboxdrv)

# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"

# -----------------------------------------------------------------------
# NETWORKING
# -----------------------------------------------------------------------
#
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
#
HOSTNAME="RVSC-LINUX"

# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
#
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
#   - prefix an entry in INTERFACES with a ! to disable it
#   - no hyphens in your interface names - Bash doesn't like it
# 
# DHCP:     Set your interface to "dhcp" (eth0="dhcp")
# Wireless: See network profiles below
#
eth0="dhcp"
INTERFACES=(eth0)

# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
#   - prefix an entry in ROUTES with a ! to disable it
#
gateway="default gw 192.168.1.1"
ROUTES=(!gateway)
 
# Enable these network profiles at boot-up.  These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
#   - set to 'menu' to present a menu during boot-up (dialog package required)
#   - prefix an entry with a ! to disable it
#
# Network profiles are found in /etc/network.d
#
# This now requires the netcfg package
#
#NETWORKS=(main)

# -----------------------------------------------------------------------
# DAEMONS
# -----------------------------------------------------------------------
#
# Daemons to start at boot-up (in this order)
#   - prefix a daemon with a ! to disable it
#   - prefix a daemon with a @ to start it up in the background
#
DAEMONS=(syslog-ng network hal fam netfs crond portmap laptop-mode gdm alsa bluetooth networkmanager cpufreq acpid dhcdbd)

Last edited by riverscn (2008-08-05 10:12:42)

tomk

Forum Fellow

From: Ireland

Registered: 2004-07-21

Posts: 9,839

Re: portmap start fail

If an initscript fails, you need to identify the actual start command from the script, run it as root in a terminal and check the output for errors.

kanim

Member

Registered: 2007-05-14

Posts: 104

Re: portmap start fail

portmap needs to be started before fam else it will fail
try to put it before fam than everything should be fine.

and you should disable network if you use network manager so just put an ! right befor network in you daemons like (... !network ...)

Last edited by kanim (2008-08-06 13:04:48)