You are not logged in.
Pages: 1
hi...
i got a new phone - Sony Ericsson k660i.
here is teh output when i'm trying mount his memory stick card.
bash-3.2# fdisk -l
Disk /dev/sda: 80.0 GB, 80026361856 bytes
255 heads, 63 sectors/track, 9729 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x00042b77
Device Boot Start End Blocks Id System
/dev/sda1 1 3657 29366820 7 HPFS/NTFS
/dev/sda2 3657 3779 979965 83 Linux
/dev/sda3 * 3779 9729 47801376 83 Linux
Disk /dev/sdb: 33 MB, 33475072 bytes
1 heads, 11 sectors/track, 5943 cylinders
Units = cylinders of 11 * 512 = 5632 bytes
Disk identifier: 0x00000000
Device Boot Start End Blocks Id System
/dev/sdb1 * 1 5936 32640+ 4 FAT16 <32M
Disk /dev/sdc: 491 MB, 491782144 bytes
32 heads, 32 sectors/track, 938 cylinders
Units = cylinders of 1024 * 512 = 524288 bytes
Disk identifier: 0x00000000
Device Boot Start End Blocks Id System
/dev/sdc1 * 1 937 479499+ 6 FAT16
bash-3.2# mount -t vfat /dev/sdc /media/mp3
mount: wrong fs type, bad option, bad superblock on /dev/sdc,
missing codepage or other error
In some cases useful info is found in syslog - try
dmesg | tail or so
bash-3.2# dmesg | tail
sd 6:0:0:1: [sdc] Test WP failed, assume Write Enabled
sd 6:0:0:1: [sdc] Assuming drive cache: write through
sdc: sdc1
sd 6:0:0:1: [sdc] Attached SCSI removable disk
sd 6:0:0:1: Attached scsi generic sg3 type 0
usb-storage: device scan complete
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev sdb.
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev sdc.
Help?
Last edited by SmarterChild (2008-08-31 21:08:38)
Offline
You should mount a partition (sdc1), not a disk (sdc).
Offline
Thanks dude, but i have another problem...
when i m mounting the part the partition [sdc1]...
or another mp3 player, i can't delete/edit files...
the permissions are for root only.
i need asolution... it's anoying to konqueror in root mode.
Offline
man mount, the whole first part and the filesystem specifics for fat and vfat. Mandatory reading.
1000
Offline
the problem isn't solved.
someone can tell me how can i mount a memory stick with normal permissions?
Thanks.
Offline
Doesn't HAL take care of mounting for you?
mount -t vfat -o gid=users,umask=0002 /dev/sdc1 /media/mp3
Last edited by lucke (2008-09-01 10:19:28)
Offline
Big Thanks Dude!
Offline
I have a similar problem trying to mount my Sony Ericsson k750i. I used to plug it in using its usb cable and it was auto mounted.
Now I get the following message from dmesg:
usb 5-2: new full speed USB device using uhci_hcd and address 7
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 8
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 9
usb 5-2: device not accepting address 9, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 10
usb 5-2: device not accepting address 10, error -71
hub 5-0:1.0: unable to enumerate USB device on port 2
I tried rmmod uhci_hcd && modprobe uhci_hcd which I 've found in google but with no result.
I think it has to do with the kernel upgrade.. Any ideas how to solve it?
Offline
I tried rmmod uhci_hcd && modprobe uhci_hcd which I 've found in google but with no result.
I was dealing with a similar issue just yesterday... the trick I found was to rmmod ehci_hcd, but don't reload it afterwards--just leave it unloaded. Then reinsert the thumb drive and see if it gets detected properly. The downside to this is that it will only operate at USB 1.0 speeds. I do think it's a regression within the kernel and from what I've seen plenty of people are complaining about it.
thayer williams ~ cinderwick.ca
Offline
axel wrote:I tried rmmod uhci_hcd && modprobe uhci_hcd which I 've found in google but with no result.
I was dealing with a similar issue just yesterday... the trick I found was to rmmod ehci_hcd, but don't reload it afterwards--just leave it unloaded. Then reinsert the thumb drive and see if it gets detected properly. The downside to this is that it will only operate at USB 1.0 speeds. I do think it's a regression within the kernel and from what I've seen plenty of people are complaining about it.
I tried rmmod ehci_hcd but again I get the same error message.
usb 5-2: new full speed USB device using uhci_hcd and address 3
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 4
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 5
usb 5-2: device not accepting address 5, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 6
usb 5-2: device not accepting address 6, error -71
hub 5-0:1.0: unable to enumerate USB device on port 2
It must have been a month ago when I last connected my phone to the usb port and at that time it was working fine. If not the kernel something else broke it.
Offline
Pages: 1