You are not logged in.
- Topics: Active | Unanswered
#1 2009-02-06 04:34:19
- interskh
- Member
- From: pittsburgh
- Registered: 2008-10-23
- Posts: 45
Any one help me with dual screen?
I am trying to get my LCD monitor work, which is plugged in VGA.
However, when i using "xrandr --output VGA --auto" to set it up, i get this failure "xrandr: cannot find crtc for output VGA"
i am using intel graphic card, and the result of "xrandr -q --verbose" is as follows,
Screen 0: minimum 320 x 200, current 1440 x 900, maximum 2960 x 1024
VGA connected (normal left inverted right x axis y axis)
Identifier: 0x3b
Timestamp: 1278799
Subpixel: unknown
Clones:
CRTCs: 0 1
1360x768 (0x41) 84.8MHz -HSync +VSync
h: width 1360 start 1432 end 1568 total 1776 skew 0 clock 47.7KHz
v: height 768 start 771 end 781 total 798 clock 59.8Hz
1152x864 (0x48) 81.6MHz -HSync +VSync
h: width 1152 start 1216 end 1336 total 1520 skew 0 clock 53.7KHz
v: height 864 start 865 end 868 total 895 clock 60.0Hz
1024x768 (0x4c) 65.0MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1344 skew 0 clock 48.4KHz
v: height 768 start 771 end 777 total 806 clock 60.0Hz
800x600 (0x51) 40.0MHz +HSync +VSync
h: width 800 start 840 end 968 total 1056 skew 0 clock 37.9KHz
v: height 600 start 601 end 605 total 628 clock 60.3Hz
640x480 (0x56) 25.2MHz -HSync -VSync
h: width 640 start 656 end 752 total 800 skew 0 clock 31.5KHz
v: height 480 start 490 end 492 total 525 clock 59.9Hz
1440x900 (0x3f) 101.6MHz
h: width 1440 start 1488 end 1520 total 1824 skew 0 clock 55.7KHz
v: height 900 start 903 end 909 total 926 clock 60.2Hz
LVDS connected 1440x900+0+0 (0x3f) normal (normal left inverted right x axis y axis) 0mm x 0mm
Identifier: 0x3c
Timestamp: 1278799
Subpixel: horizontal rgb
Clones:
CRTC: 1
CRTCs: 1
PANEL_FITTING: full
supported: center full_aspect full
BACKLIGHT_CONTROL: kernel
supported: native legacy combination kernel
BACKLIGHT: 15 (0x0000000f) range: (0,15)
1440x900 (0x3f) 101.6MHz *current +preferred
h: width 1440 start 1488 end 1520 total 1824 skew 0 clock 55.7KHz
v: height 900 start 903 end 909 total 926 clock 60.2Hz
1440x900 (0x40) 106.5MHz -HSync +VSync
h: width 1440 start 1520 end 1672 total 1904 skew 0 clock 55.9KHz
v: height 900 start 903 end 909 total 934 clock 59.9Hz
1360x768 (0x41) 84.8MHz -HSync +VSync
h: width 1360 start 1432 end 1568 total 1776 skew 0 clock 47.7KHz
v: height 768 start 771 end 781 total 798 clock 59.8Hz
1152x864 (0x42) 143.5MHz -HSync +VSync
h: width 1152 start 1232 end 1360 total 1568 skew 0 clock 91.5KHz
v: height 864 start 865 end 868 total 915 clock 100.0Hz
1152x864 (0x43) 121.5MHz +HSync -VSync
h: width 1152 start 1216 end 1344 total 1568 skew 0 clock 77.5KHz
v: height 864 start 865 end 868 total 911 clock 85.1Hz
1152x864 (0x44) 119.7MHz -HSync +VSync
h: width 1152 start 1224 end 1352 total 1552 skew 0 clock 77.1KHz
v: height 864 start 865 end 868 total 907 clock 85.0Hz
1152x864 (0x45) 108.0MHz +HSync +VSync
h: width 1152 start 1216 end 1344 total 1600 skew 0 clock 67.5KHz
v: height 864 start 865 end 868 total 900 clock 75.0Hz
1152x864 (0x46) 105.0MHz -HSync +VSync
h: width 1152 start 1224 end 1352 total 1552 skew 0 clock 67.6KHz
v: height 864 start 865 end 868 total 902 clock 75.0Hz
1152x864 (0x47) 96.8MHz -HSync +VSync
h: width 1152 start 1224 end 1344 total 1536 skew 0 clock 63.0KHz
v: height 864 start 865 end 868 total 900 clock 70.0Hz
1152x864 (0x48) 81.6MHz -HSync +VSync
h: width 1152 start 1216 end 1336 total 1520 skew 0 clock 53.7KHz
v: height 864 start 865 end 868 total 895 clock 60.0Hz
1024x768 (0x49) 94.5MHz +HSync +VSync
h: width 1024 start 1072 end 1168 total 1376 skew 0 clock 68.7KHz
v: height 768 start 769 end 772 total 808 clock 85.0Hz
1024x768 (0x4a) 78.8MHz +HSync +VSync
h: width 1024 start 1040 end 1136 total 1312 skew 0 clock 60.0KHz
v: height 768 start 769 end 772 total 800 clock 75.0Hz
1024x768 (0x4b) 75.0MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1328 skew 0 clock 56.5KHz
v: height 768 start 771 end 777 total 806 clock 70.1Hz
1024x768 (0x4c) 65.0MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1344 skew 0 clock 48.4KHz
v: height 768 start 771 end 777 total 806 clock 60.0Hz
832x624 (0x4d) 57.3MHz -HSync -VSync
h: width 832 start 864 end 928 total 1152 skew 0 clock 49.7KHz
v: height 624 start 625 end 628 total 667 clock 74.6Hz
800x600 (0x4e) 56.3MHz +HSync +VSync
h: width 800 start 832 end 896 total 1048 skew 0 clock 53.7KHz
v: height 600 start 601 end 604 total 631 clock 85.1Hz
800x600 (0x4f) 50.0MHz +HSync +VSync
h: width 800 start 856 end 976 total 1040 skew 0 clock 48.1KHz
v: height 600 start 637 end 643 total 666 clock 72.2Hz
800x600 (0x50) 49.5MHz +HSync +VSync
h: width 800 start 816 end 896 total 1056 skew 0 clock 46.9KHz
v: height 600 start 601 end 604 total 625 clock 75.0Hz
800x600 (0x51) 40.0MHz +HSync +VSync
h: width 800 start 840 end 968 total 1056 skew 0 clock 37.9KHz
v: height 600 start 601 end 605 total 628 clock 60.3Hz
800x600 (0x52) 36.0MHz +HSync +VSync
h: width 800 start 824 end 896 total 1024 skew 0 clock 35.2KHz
v: height 600 start 601 end 603 total 625 clock 56.2Hz
640x480 (0x53) 36.0MHz -HSync -VSync
h: width 640 start 696 end 752 total 832 skew 0 clock 43.3KHz
v: height 480 start 481 end 484 total 509 clock 85.0Hz
640x480 (0x54) 31.5MHz -HSync -VSync
h: width 640 start 664 end 704 total 832 skew 0 clock 37.9KHz
v: height 480 start 489 end 492 total 520 clock 72.8Hz
640x480 (0x55) 31.5MHz -HSync -VSync
h: width 640 start 656 end 720 total 840 skew 0 clock 37.5KHz
v: height 480 start 481 end 484 total 500 clock 75.0Hz
640x480 (0x56) 25.2MHz -HSync -VSync
h: width 640 start 656 end 752 total 800 skew 0 clock 31.5KHz
v: height 480 start 490 end 492 total 525 clock 59.9Hz
720x400 (0x57) 35.5MHz -HSync +VSync
h: width 720 start 756 end 828 total 936 skew 0 clock 37.9KHz
v: height 400 start 401 end 404 total 446 clock 85.0Hz
640x400 (0x58) 31.5MHz -HSync +VSync
h: width 640 start 672 end 736 total 832 skew 0 clock 37.9KHz
v: height 400 start 401 end 404 total 445 clock 85.1Hz
640x350 (0x59) 31.5MHz +HSync -VSync
h: width 640 start 672 end 736 total 832 skew 0 clock 37.9KHz
v: height 350 start 382 end 385 total 445 clock 85.1Hz
HDMI-1 connected 1360x768+0+0 (0x41) normal (normal left inverted right x axis y axis) 0mm x 0mm
Identifier: 0x3d
Timestamp: 1278799
Subpixel: unknown
Clones: HDMI-2
CRTC: 0
CRTCs: 0 1
1360x768 (0x41) 84.8MHz -HSync +VSync *current
h: width 1360 start 1432 end 1568 total 1776 skew 0 clock 47.7KHz
v: height 768 start 771 end 781 total 798 clock 59.8Hz
1152x864 (0x48) 81.6MHz -HSync +VSync
h: width 1152 start 1216 end 1336 total 1520 skew 0 clock 53.7KHz
v: height 864 start 865 end 868 total 895 clock 60.0Hz
1024x768 (0x4c) 65.0MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1344 skew 0 clock 48.4KHz
v: height 768 start 771 end 777 total 806 clock 60.0Hz
800x600 (0x51) 40.0MHz +HSync +VSync
h: width 800 start 840 end 968 total 1056 skew 0 clock 37.9KHz
v: height 600 start 601 end 605 total 628 clock 60.3Hz
640x480 (0x56) 25.2MHz -HSync -VSync
h: width 640 start 656 end 752 total 800 skew 0 clock 31.5KHz
v: height 480 start 490 end 492 total 525 clock 59.9Hz
HDMI-2 disconnected (normal left inverted right x axis y axis)
Identifier: 0x3e
Timestamp: 1278799
Subpixel: unknown
Clones: HDMI-1
CRTCs: 0 1xorg.conf is here
Section "ServerFlags"
Option "AutoAddDevices" "false"
EndSection
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Touchpad" "SendCoreEvents"
Option "AIGLX" "true"
EndSection
Section "Files"
# RgbPath "/usr/share/X11/rgb"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/misc"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/75dpi:unscaled"
FontPath "/usr/share/fonts/TTF"
FontPath "/usr/share/fonts/Type1"
EndSection
Section "Module"
Load "GLcore"
Load "xtrap"
Load "extmod"
Load "glx"
Load "dri"
# Load "record"
Load "dbe"
Load "freetype"
Load "synaptics"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbRules" "xorg"
Option "XkbModel" "thinkpad60"
Option "XkbLayout" "us"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "InputDevice"
Identifier "Touchpad"
Driver "synaptics"
Option "SendCoreEvents" "true"
Option "VertEdgeScroll" "true"
Option "HorizEdgeScroll" "true"
Option "Device" "/dev/psaux" #/dev/input/mouse0
Option "Protocol" "auto-dev"
# Option "TouchpadOff" "1" #Uncomment if you just want to disable the touchpad and use only the trackpoint
# Option "HorizScrollDelta" "0" #Why is this in here by default. By Gods, it kill horizontal scrolling!
Option "RightEdge" "5500" #This is a little bigger than the default narrowing the scroll region
Option "BottomEdge" "4500" #This is a little bigger than the default narrowing the scroll region
Option "RTCornerButton" "0" #disable Right Top corner "button"
Option "RBCornerButton" "0" #disable Right Bottom corner "button"
Option "SHMConfig" "on" #this allows configuration of the touchpad using qsynaptics, synclient, or what have you.
EndSection
Section "Monitor"
DisplaySize 304.8 190.5 # 120 dpi @1440x900
Identifier "Monitor0"
Option "DPMS"
EndSection
Section "Device"
Option "NoDDC" "true" # [<bool>]
Identifier "Card0"
Driver "intel"
VendorName "Intel Corporation"
BoardName "Mobile Integrated Graphics Controller"
BusID "PCI:0:2:0"
Option "AccelMethod" "xaa"
Option "XAANoOffscreenPixmaps" "true"
Option "DRI" "true"
Option "FramebufferCompression" "false"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1440x900" "1280x800" "1024x768" "800x600"
Virtual 2960 1024
EndSubSection
EndSection
Section "DRI"
Group "video"
Mode 0666
EndSection
Section "Extensions"
Option "Composite" "Enable"
EndSectionand now i am using awesome wm. any ideas? Thank you!!
o.O
Offline
#2 2009-02-06 07:57:04
- damjan
- Member
- Registered: 2006-05-30
- Posts: 452
Re: Any one help me with dual screen?
you already have LVDS and HDMI-1 connected... I don't think you can have 3 outputs with any intel chips.
Offline
#3 2009-02-06 13:57:35
- interskh
- Member
- From: pittsburgh
- Registered: 2008-10-23
- Posts: 45
Re: Any one help me with dual screen?
damjan wrote:
you already have LVDS and HDMI-1 connected... I don't think you can have 3 outputs with any intel chips.
do you mean I should get HDMI-1 off?
like using "xrandr --output HDMI-1 off"
i dunno where this HDMI-1 comes from.. i dont think my laptop has a HDMI-1 plug... wierd...
o.O
Offline
#4 2009-02-06 16:58:34
- konni
- Member
- From: berlin
- Registered: 2008-09-25
- Posts: 99
Re: Any one help me with dual screen?
how many monitors do you want to plugin? three? like damjan said, not sure if that works at all.
or are the hdmi outputs idle and you're just trying to plug in a second screen?
whats the exact problem? no output on that screen at all? or mirroring the internal one? in that case, try
xrandr --output VGA --right-of LVDS(or left-of...)
can you plug that monitor in with hdmi? (adapter/etc) you might try that as well, maybe just the vga fails.
Offline
#5 2009-02-06 22:07:38
- interskh
- Member
- From: pittsburgh
- Registered: 2008-10-23
- Posts: 45
Re: Any one help me with dual screen?
konni wrote:
how many monitors do you want to plugin? three? like damjan said, not sure if that works at all.
or are the hdmi outputs idle and you're just trying to plug in a second screen?
whats the exact problem? no output on that screen at all? or mirroring the internal one? in that case, tryxrandr --output VGA --right-of LVDS(or left-of...)
can you plug that monitor in with hdmi? (adapter/etc) you might try that as well, maybe just the vga fails.
wow.. thank you konni... and thank damjan
i turned off HDMI-1, then I could get VGA work!
now i have dual screens, pretty cool.
o.O
Offline