xorg-server 1.6 flgrx->xf86-video-ati

mmre · 2009-04-19 11:14:06

Hello,

I used fglrx with no problems over months but no I have to switch (because of xorg-server 1.6.). My graphic card is ATI Mobility X700, my configuration is that I have a laptop monitor (1280x800) and a other monitor (22" widescreen 1680x1050). My old configuration was that the big monitor is left-of the LVDS and Xinerama was active, I could pull windows from LVDS to the big screen. I would prefer the same configuration with the free driver, but I can't configure the xorg.conf that it works. It would be awesome if somebody can create or help me with the xorg.conf. No xorg.conf is also not a good way, because I got the wrong resolution and just one screen is active.

Btw. what is different between xf86-video-ati in the repos and xf86-video-ati-git in the AUR?

Thanks a lot

signor_rossi · 2009-04-19 16:00:14

xf86-video-ati-git most important of all gives you basic support for power saving, especially needed for a X700 Mobility(Rxxx?). I have a X600 and did the switch a few days back and must say that everything works better now with radeon from git! Power saving support is still rudimentary for my X600 (RV380) and doesn't save as much power as PowerPlay of fglrx did (saves 3W atm on battery), but I can enable power saving with two monitors attached now and video playback is still smooth and even Goggle Earth works better than ever before.
Just install radeoon from GIT, load the new module and create a new xorg.conf with 'X -configure'. Copy the xorg.conf to '/etc/X11' and uncomment the 'ForceLowPowerMode' option and also add a 'Virtual 2960 1050' line to your Display subsection in your xorg.conf. Then 'startx' and configure your monitors with 'xrandr'. Something like this:
xrandr --output LVDS --mode 1680x1050 &
xrandr --output DVI-0 --mode 1280x1024 &
xrandr --output DVI-0 --pos 1680x0 &

See if you can get it going and I will help you refine things later...

SignorRossi.

mmre · 2009-04-19 18:09:40

What to do mean with "load the new module"?

Thanks

signor_rossi · 2009-04-19 18:16:52

mmre wrote:

What to do mean with "load the new module"?
Thanks

To not forget that when you deinstall xf86-video-ati and install xf86-video-ati-git that you need to unload the old radeon module and load the new one unless you reboot...

mmre · 2009-04-19 19:00:09

Ok, I load the module "ati" at rc.conf or is better at xorg.conf?
The LVDS-screen is black and my VGA-0 is not started with the best resolution. I execute: xrandr --output VGA-0 --mode 1680x1050 and this enable a better resolution. But when I try to execute: xrandr --output LVDS --mode 1280x800 --right-of VGA-0
xrandr: screen cannot be larger than 1680x1680 (desired size 2960x1050)

Although Virtual with 2960 1050 is a subsection of Screen. Where is the mistake?

Thanks

My xorg.conf:

Section "ServerLayout"
    Identifier     "X.org Configured"
    Screen      0  "Screen0" 0 0
    InputDevice    "Mouse0" "CorePointer"
    InputDevice    "Keyboard0" "CoreKeyboard"
#    Option        "Xinerama" "true" 
EndSection

Section "Files"
    ModulePath   "/usr/lib/xorg/modules"
    FontPath     "/usr/share/fonts/misc"
    FontPath     "/usr/share/fonts/100dpi:unscaled"
    FontPath     "/usr/share/fonts/75dpi:unscaled"
    FontPath     "/usr/share/fonts/TTF"
    FontPath     "/usr/share/fonts/Type1"
EndSection

Section "Module"
    Load  "record"
    Load  "dbe"
    Load  "glx"
    Load  "dri2"
    Load  "dri"
    Load  "extmod"
EndSection

Section "InputDevice"
    Identifier  "Keyboard0"
    Driver      "kbd"
EndSection

Section "InputDevice"
    Identifier  "Mouse0"
    Driver      "mouse"
    Option        "Protocol" "auto"
    Option        "Device" "/dev/input/mice"
    Option        "ZAxisMapping" "4 5 6 7"
EndSection

Section "Monitor"
    #DisplaySize      330   210    # mm
    Identifier   "Monitor0"
    VendorName   "QDS"
    ModelName    "1c"
EndSection

Section "Device"
        ### Available Driver options are:-
        ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
        ### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
        ### [arg]: arg optional
        #Option     "NoAccel"                # [<bool>]
        #Option     "SWcursor"               # [<bool>]
        #Option     "Dac6Bit"                # [<bool>]
        #Option     "Dac8Bit"                # [<bool>]
        #Option     "BusType"                # [<str>]
        #Option     "CPPIOMode"              # [<bool>]
        #Option     "CPusecTimeout"          # <i>
        #Option     "AGPMode"                # <i>
        #Option     "AGPFastWrite"           # [<bool>]
        #Option     "AGPSize"                # <i>
        #Option     "GARTSize"               # <i>
        #Option     "RingSize"               # <i>
        #Option     "BufferSize"             # <i>
        #Option     "EnableDepthMoves"       # [<bool>]
        #Option     "EnablePageFlip"         # [<bool>]
        #Option     "NoBackBuffer"           # [<bool>]
        #Option     "DMAForXv"               # [<bool>]
        #Option     "FBTexPercent"           # <i>
        #Option     "DepthBits"              # <i>
        #Option     "PCIAPERSize"            # <i>
        #Option     "AccelDFS"               # [<bool>]
        #Option     "IgnoreEDID"             # [<bool>]
        #Option     "DisplayPriority"        # [<str>]
        #Option     "PanelSize"              # [<str>]
        #Option     "ForceMinDotClock"       # <freq>
        #Option     "ColorTiling"            # [<bool>]
        #Option     "VideoKey"               # <i>
        #Option     "RageTheatreCrystal"     # <i>
        #Option     "RageTheatreTunerPort"     # <i>
        #Option     "RageTheatreCompositePort"     # <i>
        #Option     "RageTheatreSVideoPort"     # <i>
        #Option     "TunerType"              # <i>
        #Option     "RageTheatreMicrocPath"     # <str>
        #Option     "RageTheatreMicrocType"     # <str>
        #Option     "ScalerWidth"            # <i>
        #Option     "RenderAccel"            # [<bool>]
        #Option     "SubPixelOrder"          # [<str>]
        #Option     "ShowCache"              # [<bool>]
        #Option     "ClockGating"            # [<bool>]
        #Option     "VGAAccess"              # [<bool>]
        #Option     "ReverseDDC"             # [<bool>]
        #Option     "LVDSProbePLL"           # [<bool>]
        #Option     "AccelMethod"            # <str>
        #Option     "DRI"                    # [<bool>]
        #Option     "ConnectorTable"         # <str>
        #Option     "DefaultConnectorTable"     # [<bool>]
        #Option     "DefaultTMDSPLL"         # [<bool>]
        #Option     "TVDACLoadDetect"        # [<bool>]
        #Option     "ForceTVOut"             # [<bool>]
        #Option     "TVStandard"             # <str>
        #Option     "IgnoreLidStatus"        # [<bool>]
        #Option     "DefaultTVDACAdj"        # [<bool>]
        #Option     "Int10"                  # [<bool>]
        #Option     "EXAVSync"               # [<bool>]
        #Option     "ATOMTVOut"              # [<bool>]
        #Option     "R4xxATOM"               # [<bool>]
        Option     "ForceLowPowerMode"      # [<bool>]
        #Option     "DynamicPM"              # [<bool>]
    Identifier  "Card0"
    Driver      "radeon"
    VendorName  "ATI Technologies Inc"
    BoardName   "Radeon Mobility X700 (PCIE)"
    BusID       "PCI:1:0:0"
EndSection

Section "Screen"
    Identifier "Screen0"
    Device     "Card0"
    Monitor    "Monitor0"
    SubSection "Display"
        Virtual 2960 1050
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     1
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     4
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     8
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     15
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     16
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     24
    EndSubSection
EndSection

signor_rossi · 2009-04-19 19:19:14

I guess 'Virtual' has to go here and in all other subsections for the color depths you use.

SubSection "Display"
Viewport 0 0
Depth 24
Virtual 2960 1050
EndSubSection

And the module is named radeon, but I guess it gets already automatically loaded. Besides that you load it via the Modules section in rc.conf.
About X starting with the right setup without calling xrandr manually, it depends on how you start X how to do it. Am I right that you use gdm or kdm?

EDIT: And the option to enable power saving goes like this:
Option "ForceLowPowerMode" "true"

Keep in mind that this sets the card in permanent power saving mode. And sorry that I wasn't more precise in my first post, but I was in a hurry.

Last edited by signor_rossi (2009-04-19 19:24:05)

mmre · 2009-04-19 19:44:07

Yes, I'm using KDM.

Ok,Virtual works, but not correctly. After xrandr --output VGA-0 --mode 1680x1050 the resolution of VGA-0 is high. Here is perhaps a useful output:

xrandr -q
Screen 0: minimum 320 x 200, current 1680 x 1050, maximum 2960 x 1050
VGA-0 connected 1680x1050+0+0 (normal left inverted right x axis y axis) 473mm x 297mm
   1680x1050      59.9*+   60.0
   1280x1024      75.0     60.0
   1440x900       75.0     59.9
   1280x960       60.0
   1280x800       59.8
   1152x864       75.0
   1152x720       60.0
   1024x768       75.0     60.0
   832x624        74.6
   800x600        75.0     60.3
   640x480        75.0     59.9
   720x400        70.1
LVDS connected 1280x800+0+0 (normal left inverted right x axis y axis) 331mm x 207mm
   1280x800       60.0*+
   1280x720       59.9
   1152x768       59.8
   1024x768       59.9
   800x600        59.9
   640x480        59.4
DVI-0 disconnected (normal left inverted right x axis y axis)

But xrandr --output LVDS --mode 1280x800 does not work. There is no error message but the laptop screen is still black, there's nothing to see. Positioning with --right of VGA-0 has also no effect. I don't know what to do. Anyway xrandr never saves the new better resolution, but I think that is normal. First get it to work with xrandr, than writing it down to the xorg.conf

ForceLowPowerMode is now true.

signor_rossi · 2009-04-19 20:22:51

It is strange that the laptop screen is black because xrandr marks the active modes with an asterisk and those marked are the right ones and LVDS is also enabled. Since you use kdm you probably also use kde, right? I ask because I myself had to start with a clean kde config (by renaming .kde4) to make it work, otherwise plasma would crash and not run at all. It was also the same for Xfce4. Even before when I changed some commands that set the right resolution, position on X startup I messed things up and had to start with a clean config again. Sstrangely setting resolution of the first and second monitor and x,y position of the second monitor makes kde start right, ut also calling also 'xrandr --output DVI-0 --left-of LVDS' screwes things up. This is done in '/usr/share/config/kdm/Xsetup' like this, so you don't have to do it manually.
xrandr --output LVDS --mode 1680x1050 &
xrandr --output DVI-0 --mode 1280x1024 &
xrandr --output DVI-0 --pos 1680x0 &

The KDE systemsettings module for xrandr never worked for me.

signor_rossi · 2009-04-19 20:30:09

Found something. In your xrandr output you see that both screens start at the same coordinates, at x=0, y=0. Did you issue the command 'xrandr --output VGA-0 --pos 1280x0' correctly (this is the command when your external monitor sits right of your laptop monitor)? I had to use the pos command because otherwise my two monitors would overlap. Please post the exact commands you issue.

veek · 2009-04-20 07:14:09

I stumbled on this thread while trying to get multi head working on a very similar setup (laptop, X.org 1.6.1, radeon driver, external monitor).

Ultimately two minor things were sufficient to get it working for me (did not need xinerama, twinview (nvidia), or MergedFB (ati)).

*Added the "Virtual" directives to the Display sub section in the Screen section of xorg.conf; as you've already done.

*Used xrandr to activate the second display. signor_rossi's method should definitely work (I suspect the observations in his last post are correct), but I also found an alternative one-liner in the wiki that also works. In your case it would be:

xrandr --output VGA-0 --right-of LVDS

I was able to issue the command in a terminal after starting X...and there it was, display number 2 ( and not a clone of disp. 1). I'm impressed by how little effort it required. Took some doing to find out what was necessary, but in the end, very easy.

I'm mainly posting this to confirm that the method does work, and furthermore it works with xmonad under the latest X server.

For anyone curious about xmonad and multiple displays:

At first using a multi head setup in xmonad is a bit mind bending, but after getting oriented it's really nice. One danger is you might get it working without even realizing it started working properly. A status bar with the workspace information is really helpful in understanding how workspaces (equivalent to virtual desktops in other WMs) function in xmonad when there are multiple displays.

One unique (I think) behavior is that the new display area is not used by stretching a single workspace onto the extra displays. Instead, each extra display shows a separate workspace, and all displays can be controlled independentally.

For example, by default there are 9 workspaces in xmonad. With a laptop and an external monitor, the laptop could be displaying workspace 3, with the external monitor showing workspace 5. Subsequently the laptop could be switched to workspace 2 with the monitor remaining on workspace 5.

Quite cool, and if I'm not mistaken, fundamentally different from other window managers in a multi display environment.

final note: The xmonad FAQ describes the default multi head workspace swapping behavior and shows how to change it (felt unintuitive to me).

Last edited by veek (2009-04-20 07:15:40)

signor_rossi · 2009-04-20 08:52:10

@veek
'xrandr --output VGA-0 --right-of LVDS'
is almost the same command (only that my second display is connected via DVI and therefore called DVI-0) I issued when i set up things manually besides 'xrandr --output LVDS --mode 1680x1050'. 'xrandr --output DVI-0 --pos 1680x0' is the command I had to use additionally in my setup to not make the two monitors overlap, without it I would see part of the output of DVI-0 on LVDS. to add to the confusion, 'xrandr --output DVI-0 --right-of LVDS' executed via the automatic kdm method would screw things up and give me only the same output on both my displays.
Just to make things clearer to anyone interested.

mmre · 2009-04-20 14:46:41

'xrandr --output VGA-0 --right-of LVDS' does NOT work. LVDS is still black and on the big screen I can't see any icons or the taskbar. I can just see the konsole that I used to execute the code and the background is the default blue KDE theme with bubbels..

After xrandr --output LVDS --mode 1280x800 & xrandr --output VGA-0 --right-of LVDS (just one command let LVDS also black) I got:

xrandr -q
Screen 0: minimum 320 x 200, current 2960 x 1050, maximum 2960 x 1050
VGA-0 connected 1680x1050+1280+0 (normal left inverted right x axis y axis) 473mm x 297mm
   1680x1050      59.9*+   60.0
   1280x1024      75.0     60.0
   1440x900       75.0     59.9
   1280x960       60.0
   1280x800       59.8
   1152x864       75.0
   1152x720       60.0
   1024x768       75.0     60.0
   832x624        74.6
   800x600        75.0     60.3
   640x480        75.0     59.9
   720x400        70.1
LVDS connected 1280x800+0+0 (normal left inverted right x axis y axis) 331mm x 207mm
   1280x800       60.0*+
   1280x720       59.9
   1152x768       59.8
   1024x768       59.9
   800x600        59.9
   640x480        59.4

signor_rossi · 2009-04-20 15:05:34

mmre wrote:

'xrandr --output VGA-0 --right-of LVDS' does NOT work. LVDS is still black and on the big screen I can't see any icons or the taskbar. I can just see the konsole that I used to execute the code and the background is the default blue KDE theme with bubbels..
After xrandr --output LVDS --mode 1280x800 & xrandr --output VGA-0 --right-of LVDS (just one command let LVDS also black) I got:
xrandr -q
Screen 0: minimum 320 x 200, current 2960 x 1050, maximum 2960 x 1050
VGA-0 connected 1680x1050+1280+0 (normal left inverted right x axis y axis) 473mm x 297mm
   1680x1050      59.9*+   60.0
   1280x1024      75.0     60.0
   1440x900       75.0     59.9
   1280x960       60.0
   1280x800       59.8
   1152x864       75.0
   1152x720       60.0
   1024x768       75.0     60.0
   832x624        74.6
   800x600        75.0     60.3
   640x480        75.0     59.9
   720x400        70.1
LVDS connected 1280x800+0+0 (normal left inverted right x axis y axis) 331mm x 207mm
   1280x800       60.0*+
   1280x720       59.9
   1152x768       59.8
   1024x768       59.9
   800x600        59.9
   640x480        59.4

Output seems right.
But did you already try with a clean kde config or start a twm session only? Like I mentioned before KDE would not run properly with my existing kde config.

mmre · 2009-04-20 16:47:26

Removed .kde4 and restart and tried 'xrandr --output VGA-0 --mode 1680x1050 & xrandr --output LVDS --mode 1280x800 & xrandr --output VGA-0 --right-of LVDS'.
The same (just wallpaper) and now without the shell where I execute the command. The LVDS-screen is still black. Seems too be very strange. Any output useful? Xorg, dmesg?

anakin · 2009-04-21 10:38:21

I'm having the EXACT same problem as mmre. All the xrandr commands are issued correctly and the output seems right, BUT LVDS (the laptop LCD) goes black as soon as VGA-0 is enabled. It seems like they can't be both working at the same time for some odd reason. This is not a hardware issue since my setup works correctly under XP and also on Ubuntu.

Any news?

PS:

I'm still using xf86-video-ati from the extra repo, not the git version from AUR and I've noticed this fatal error in Xorg.0.log when using Option "RightOf" "LVDS" in Xorg.conf:

(EE) RADEON(0): Acceleration required for rotation

If I remove this option Xorg starts but only VGA-0 works, LVDS goes blank.

Last edited by anakin (2009-04-21 11:12:07)

carlocci · 2009-04-21 12:23:56

It seems xrandr is somewhat broken.
I had a similar problem, I was able to solve it turning off a monitor, wait, set the other, wait, set the first one left-of/right-of

xrandr --output VGA-0 --off
sleep 5
xrandr --output DVI-0 whatever
sleep 5
xrandr --output VGA-0 --mode 1024x768 --left-of DVI-0

anakin · 2009-04-21 17:35:32

OK, confirmed!

As soon as I've relaced xf86-video-ati with xf86-video-ati-git from the AUR xrandr started working perfectly, no more blank LVDS! Thus I assume there's something wrong with the driver on the extra repo.

mmre are you running the git version? If not, that might be your problem.

mmre · 2009-04-22 19:59:00

@carlocci
Still doesn't work. It seems like there is a screen at LVDS (I can go there with the mouse) but LVDS is black, nothing to see.
What's your graphic card? I use ATI Mobility X700.

yaourt -Ss xf86-video-ati-git:

aur/xf86-video-ati-git 20090419-1 [installed] (42)
    X.org ati video driver

Perhaps intresting output in Xorg.log file:

@(WW) RADEON(0): LVDS Info:
XRes: 1280, YRes: 800, DotClock: 68900
HBlank: 128, HOverPlus: 21, HSyncWidth: 32
VBlank: 16, VOverPlus: 4, VSyncWidth: 4

(WW) RADEON(0): Unknown vendor-specific block f

(WW) RADEON(0): DRI init changed memory map, adjusting ...
(WW) RADEON(0):   MC_FB_LOCATION  was: 0xd7ffd000 is: 0xd7ffd000
(WW) RADEON(0):   MC_AGP_LOCATION was: 0xffffffc0 is: 0xffffffc0

mmre · 2009-04-26 19:50:43

Any new idea? The KDEMod system setting doesn't work too. If I use identify, both (VGA-0 & LVDS) are the same screen. Is there another tool than xrandr?

signor_rossi · 2009-04-26 20:20:02

systemsettings never worked for me either, 'Display Settings' is borked in regard to dual monitors...
Haven't a clue anymore, but maybe at the phoronix forums someone can help you (radeon driver devs can be found there)...
http://www.phoronix.com/forums/forumdisplay.php?f=43

banshee28 · 2009-04-27 00:14:38

Anyone using this for x64? I cant seem to download and install the git driver. It gets almost to the end then errors out:

error: package "./xf86-video-ati-git-20090419-1-x86_64.pkg.tar.gz" not found
error: package "./xf86-video-ati-git-20090419-1-x86_64.pkg.tar.gz" not found
==>  Continue installing xf86-video-ati-git? [Y/n]
==>  [v]iew package contents [c]heck package with namcap
==>   ----------------------------------------------
==>y

loading package data...
error: './xf86-video-ati-git-20090419-1-x86_64.pkg.tar.gz': cannot open package file
==> WARNING: Your package is saved in /tmp/yaourt-tmp-root/xf86-video-ati-git-20090419-1-x86_64.pkg.tar.gz
cp: cannot stat `./xf86-video-ati-git-20090419-1-x86_64.pkg.tar.gz': No such file or directory
==> WARNING: Unable to copy xf86-video-ati-git-1-x86_64.pkg.tar.gz to /tmp/yaourt-tmp-root/ directory
If you like this package, please install aurvote
and vote for its inclusion/keeping in [community]

bash-3.2#

EDIT: I think this has to do with my AUR config and not this ati-git driver as its giving the same error installing another aur pkg!

Last edited by banshee28 (2009-04-27 01:55:56)

signor_rossi · 2009-04-27 06:19:07

banshee28 wrote:

Anyone using this for x64? I cant seem to download and install the git driver. It gets almost to the end then errors out:

error: package "./xf86-video-ati-git-20090419-1-x86_64.pkg.tar.gz" not found
error: package "./xf86-video-ati-git-20090419-1-x86_64.pkg.tar.gz" not found
==>  Continue installing xf86-video-ati-git? [Y/n]
==>  [v]iew package contents [c]heck package with namcap
==>   ----------------------------------------------
==>y

loading package data...
error: './xf86-video-ati-git-20090419-1-x86_64.pkg.tar.gz': cannot open package file
==> WARNING: Your package is saved in /tmp/yaourt-tmp-root/xf86-video-ati-git-20090419-1-x86_64.pkg.tar.gz
cp: cannot stat `./xf86-video-ati-git-20090419-1-x86_64.pkg.tar.gz': No such file or directory
==> WARNING: Unable to copy xf86-video-ati-git-1-x86_64.pkg.tar.gz to /tmp/yaourt-tmp-root/ directory
If you like this package, please install aurvote
and vote for its inclusion/keeping in [community]

bash-3.2#

EDIT: I think this has to do with my AUR config and not this ati-git driver as its giving the same error installing another aur pkg!

Are you using yaourt (I don't)? If yes, have you tried already to do the installation manually?

flamelab · 2009-04-27 11:04:43

banshee28 wrote:

Anyone using this for x64? I cant seem to download and install the git driver. It gets almost to the end then errors out:

error: package "./xf86-video-ati-git-20090419-1-x86_64.pkg.tar.gz" not found
error: package "./xf86-video-ati-git-20090419-1-x86_64.pkg.tar.gz" not found
==>  Continue installing xf86-video-ati-git? [Y/n]
==>  [v]iew package contents [c]heck package with namcap
==>   ----------------------------------------------
==>y

loading package data...
error: './xf86-video-ati-git-20090419-1-x86_64.pkg.tar.gz': cannot open package file
==> WARNING: Your package is saved in /tmp/yaourt-tmp-root/xf86-video-ati-git-20090419-1-x86_64.pkg.tar.gz
cp: cannot stat `./xf86-video-ati-git-20090419-1-x86_64.pkg.tar.gz': No such file or directory
==> WARNING: Unable to copy xf86-video-ati-git-1-x86_64.pkg.tar.gz to /tmp/yaourt-tmp-root/ directory
If you like this package, please install aurvote
and vote for its inclusion/keeping in [community]

bash-3.2#

EDIT: I think this has to do with my AUR config and not this ati-git driver as its giving the same error installing another aur pkg!

Download it locally and run "makepkg". Yaourt has problems, and, as I can see, it didn't change the GIT version to the latest date.

banshee28 · 2009-04-28 02:00:28

Thanks for all the reply's. I was finally able to get it working with yaourt. For some strange reason it would not install as root, but only as a normal user then entering the root pw when needed.

I have it installed and now trying to get both screens configured and acting like 2 separate X screens.

mmre · 2009-04-28 15:09:10

Somewhere must be the error...
I attached the xrandr --verbose output after executing the command "xrandr --output VGA-0 --pos 0x0 --mode 1680x1050 --output LVDS --pos 1680x0 --mode 1280x800"

Screen 0: minimum 320 x 200, current 2960 x 1050, maximum 2960 x 1050
VGA-0 connected 1680x1050+0+0 (0x4f) normal (normal left inverted right x axis y axis) 473mm x 297mm
    Identifier: 0x4c
    Timestamp:  23211
    Subpixel:   no subpixels
    Clones:     DVI-0
    CRTC:       1
    CRTCs:      0 1
    Transform:  1.000000 0.000000 0.000000
                0.000000 1.000000 0.000000
                0.000000 0.000000 1.000000
               filter: 
    EDID_DATA:
        00ffffffffffff0009d10d7845540000
        2a1201030e2f1e782ec4f6a3574a9c23
        114f54a56b80710081009500950f8180
        8140b30001017c2e90a0601a1e403020
        3600d92911000018000000ff00464138
        30313232335a4c300a20000000fd0037
        4c1f5311000a202020202020000000fc
        0042656e51204732323030570a200036
    load_detection: 1 (0x00000001)    range:  (0,1)
  1680x1050 (0x4f)  119.0MHz -HSync -VSync *current +preferred
        h: width  1680 start 1728 end 1760 total 1840 skew    0 clock   64.7KHz
        v: height 1050 start 1053 end 1059 total 1080           clock   59.9Hz
  1680x1050 (0x50)  146.2MHz -HSync +VSync
        h: width  1680 start 1784 end 1960 total 2240 skew    0 clock   65.3KHz
        v: height 1050 start 1053 end 1059 total 1089           clock   60.0Hz
  1280x1024 (0x51)  135.0MHz +HSync +VSync
        h: width  1280 start 1296 end 1440 total 1688 skew    0 clock   80.0KHz
        v: height 1024 start 1025 end 1028 total 1066           clock   75.0Hz
  1280x1024 (0x52)  108.0MHz +HSync +VSync
        h: width  1280 start 1328 end 1440 total 1688 skew    0 clock   64.0KHz
        v: height 1024 start 1025 end 1028 total 1066           clock   60.0Hz
  1440x900 (0x53)  136.8MHz -HSync +VSync
        h: width  1440 start 1536 end 1688 total 1936 skew    0 clock   70.6KHz
        v: height  900 start  903 end  909 total  942           clock   75.0Hz
  1440x900 (0x54)  106.5MHz -HSync +VSync
        h: width  1440 start 1520 end 1672 total 1904 skew    0 clock   55.9KHz
        v: height  900 start  903 end  909 total  934           clock   59.9Hz
  1280x960 (0x55)  108.0MHz +HSync +VSync
        h: width  1280 start 1376 end 1488 total 1800 skew    0 clock   60.0KHz
        v: height  960 start  961 end  964 total 1000           clock   60.0Hz
  1280x800 (0x56)   83.5MHz -HSync +VSync
        h: width  1280 start 1352 end 1480 total 1680 skew    0 clock   49.7KHz
        v: height  800 start  803 end  809 total  831           clock   59.8Hz
  1152x864 (0x57)  108.0MHz +HSync +VSync
        h: width  1152 start 1216 end 1344 total 1600 skew    0 clock   67.5KHz
        v: height  864 start  865 end  868 total  900           clock   75.0Hz
  1152x720 (0x58)   67.3MHz -HSync +VSync
        h: width  1152 start 1208 end 1328 total 1504 skew    0 clock   44.8KHz
        v: height  720 start  721 end  724 total  746           clock   60.0Hz
  1024x768 (0x59)   78.8MHz +HSync +VSync
        h: width  1024 start 1040 end 1136 total 1312 skew    0 clock   60.0KHz
        v: height  768 start  769 end  772 total  800           clock   75.0Hz
  1024x768 (0x5a)   65.0MHz -HSync -VSync
        h: width  1024 start 1048 end 1184 total 1344 skew    0 clock   48.4KHz
        v: height  768 start  771 end  777 total  806           clock   60.0Hz
  832x624 (0x5b)   57.3MHz -HSync -VSync
        h: width   832 start  864 end  928 total 1152 skew    0 clock   49.7KHz
        v: height  624 start  625 end  628 total  667           clock   74.6Hz
  800x600 (0x5c)   49.5MHz +HSync +VSync
        h: width   800 start  816 end  896 total 1056 skew    0 clock   46.9KHz
        v: height  600 start  601 end  604 total  625           clock   75.0Hz
  800x600 (0x5d)   40.0MHz +HSync +VSync
        h: width   800 start  840 end  968 total 1056 skew    0 clock   37.9KHz
        v: height  600 start  601 end  605 total  628           clock   60.3Hz
  640x480 (0x5e)   31.5MHz -HSync -VSync
        h: width   640 start  656 end  720 total  840 skew    0 clock   37.5KHz
        v: height  480 start  481 end  484 total  500           clock   75.0Hz
  640x480 (0x5f)   25.2MHz -HSync -VSync
        h: width   640 start  656 end  752 total  800 skew    0 clock   31.5KHz
        v: height  480 start  490 end  492 total  525           clock   59.9Hz
  720x400 (0x60)   28.3MHz -HSync +VSync
        h: width   720 start  738 end  846 total  900 skew    0 clock   31.5KHz
        v: height  400 start  412 end  414 total  449           clock   70.1Hz
LVDS connected 1280x800+1680+0 (0x61) normal (normal left inverted right x axis y axis) 331mm x 207mm
    Identifier: 0x4d
    Timestamp:  23211
    Subpixel:   horizontal rgb
    Clones:    
    CRTC:       0
    CRTCs:      0
    Transform:  1.000000 0.000000 0.000000
                0.000000 1.000000 0.000000
                0.000000 0.000000 1.000000
               filter: 
    EDID_DATA:
        00ffffffffffff0044931c0000000000
        000f0103802115780a4dc0935c518827
        21505400000001010101010101010101
        010101010101ea1a0080502010301520
        44004bcf100000180000000f0008002a
        0001000400324a041401000000fe0051
        55414e5441444953504c4159000000fe
        0051443135544c3032310a20202000b9
    scaler: full
  1280x800 (0x61)   68.9MHz -HSync -VSync *current +preferred
        h: width  1280 start 1301 end 1333 total 1408 skew    0 clock   48.9KHz
        v: height  800 start  804 end  808 total  816           clock   60.0Hz
  1280x720 (0x62)   74.5MHz -HSync +VSync
        h: width  1280 start 1344 end 1472 total 1664 skew    0 clock   44.8KHz
        v: height  720 start  723 end  728 total  748           clock   59.9Hz
  1152x768 (0x63)   71.8MHz -HSync +VSync
        h: width  1152 start 1216 end 1328 total 1504 skew    0 clock   47.7KHz
        v: height  768 start  771 end  781 total  798           clock   59.8Hz
  1024x768 (0x64)   63.5MHz -HSync +VSync
        h: width  1024 start 1072 end 1176 total 1328 skew    0 clock   47.8KHz
        v: height  768 start  771 end  775 total  798           clock   59.9Hz
  800x600 (0x65)   38.2MHz -HSync +VSync
        h: width   800 start  832 end  912 total 1024 skew    0 clock   37.4KHz
        v: height  600 start  603 end  607 total  624           clock   59.9Hz
  640x480 (0x66)   23.8MHz -HSync +VSync
        h: width   640 start  664 end  720 total  800 skew    0 clock   29.7KHz
        v: height  480 start  483 end  487 total  500           clock   59.4Hz
DVI-0 disconnected (normal left inverted right x axis y axis)
    Identifier: 0x4e
    Timestamp:  23211
    Subpixel:   no subpixels
    Clones:     VGA-0
    CRTCs:      0 1
    Transform:  1.000000 0.000000 0.000000
                0.000000 1.000000 0.000000
                0.000000 0.000000 1.000000
               filter: 
    scaler: off
    tmds_pll: bios

Arch Linux

#1 2009-04-19 11:14:06

xorg-server 1.6 flgrx->xf86-video-ati

#2 2009-04-19 16:00:14

Re: xorg-server 1.6 flgrx->xf86-video-ati

#3 2009-04-19 18:09:40

Re: xorg-server 1.6 flgrx->xf86-video-ati

#4 2009-04-19 18:16:52

Re: xorg-server 1.6 flgrx->xf86-video-ati

#5 2009-04-19 19:00:09

Re: xorg-server 1.6 flgrx->xf86-video-ati

#6 2009-04-19 19:19:14

Re: xorg-server 1.6 flgrx->xf86-video-ati

#7 2009-04-19 19:44:07

Re: xorg-server 1.6 flgrx->xf86-video-ati

#8 2009-04-19 20:22:51

Re: xorg-server 1.6 flgrx->xf86-video-ati

#9 2009-04-19 20:30:09

Re: xorg-server 1.6 flgrx->xf86-video-ati

#10 2009-04-20 07:14:09

Re: xorg-server 1.6 flgrx->xf86-video-ati

#11 2009-04-20 08:52:10

Re: xorg-server 1.6 flgrx->xf86-video-ati

#12 2009-04-20 14:46:41

Re: xorg-server 1.6 flgrx->xf86-video-ati

#13 2009-04-20 15:05:34

Re: xorg-server 1.6 flgrx->xf86-video-ati

#14 2009-04-20 16:47:26

Re: xorg-server 1.6 flgrx->xf86-video-ati

#15 2009-04-21 10:38:21

Re: xorg-server 1.6 flgrx->xf86-video-ati

#16 2009-04-21 12:23:56

Re: xorg-server 1.6 flgrx->xf86-video-ati

#17 2009-04-21 17:35:32

Re: xorg-server 1.6 flgrx->xf86-video-ati

#18 2009-04-22 19:59:00

Re: xorg-server 1.6 flgrx->xf86-video-ati

#19 2009-04-26 19:50:43

Re: xorg-server 1.6 flgrx->xf86-video-ati

#20 2009-04-26 20:20:02

Re: xorg-server 1.6 flgrx->xf86-video-ati

#21 2009-04-27 00:14:38

Re: xorg-server 1.6 flgrx->xf86-video-ati

#22 2009-04-27 06:19:07

Re: xorg-server 1.6 flgrx->xf86-video-ati

#23 2009-04-27 11:04:43

Re: xorg-server 1.6 flgrx->xf86-video-ati

#24 2009-04-28 02:00:28

Re: xorg-server 1.6 flgrx->xf86-video-ati

#25 2009-04-28 15:09:10

Re: xorg-server 1.6 flgrx->xf86-video-ati

Board footer