You are not logged in.
Pages: 1
First of all my problem is that my kernel has some ACPI errors which should be fixed somehow but I don't know exactly. I've already patched my kernel to fix the broken dsdt table but I think the patch wasn't proceeding to 100% so this could be a mistake. Finally I hope somebody could help me with this issue but thats not all.
I will post my kernel config and hope that somebody can say me some things I will definitly not need to build into my kernel or build as a module. I ask because in some config points I'm not quite sure If I need it or not so this kernel is bloated and eventually some things I would need (e.g. card reader) aren't build in. So first of all I'll give you my lspci to look at:
00:00.0 Host bridge: Intel Corp.: Unknown device 3340 (rev 03)
00:01.0 PCI bridge: Intel Corp.: Unknown device 3341 (rev 03)
00:1d.0 USB Controller: Intel Corp. 82801DB USB (Hub #1) (rev 01)
00:1d.1 USB Controller: Intel Corp. 82801DB USB (Hub #2) (rev 01)
00:1d.2 USB Controller: Intel Corp. 82801DB USB (Hub #3) (rev 01)
00:1d.7 USB Controller: Intel Corp. 82801DB USB EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev 81)
00:1f.0 ISA bridge: Intel Corp.: Unknown device 24cc (rev 01)
00:1f.1 IDE interface: Intel Corp.: Unknown device 24ca (rev 01)
00:1f.3 SMBus: Intel Corp. 82801DB SMBus (rev 01)
00:1f.5 Multimedia audio controller: Intel Corp. 82801DB AC'97 Audio (rev 01)
00:1f.6 Modem: Intel Corp. 82801DB AC'97 Modem (rev 01)
01:00.0 VGA compatible controller: nVidia Corporation: Unknown device 0328 (reva1)
02:03.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev ac)
02:03.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev ac)
02:03.2 FireWire (IEEE 1394): Ricoh Co Ltd R5C552 IEEE 1394 Controller (rev 04)
02:05.0 Ethernet controller: Broadcom Corporation BCM4401 100Base-T (rev 01)
02:07.0 Network controller: Intel Corp.: Unknown device 4220 (rev 05)Here comes my dmesg:
Linux version 2.6.9 (root@Golgotha) (gcc version 3.4.2) #5 Sat Nov 6 19:23:15 CET 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d0000 - 00000000000d4000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ff70000 (usable)
BIOS-e820: 000000001ff70000 - 000000001ff7c000 (ACPI data)
BIOS-e820: 000000001ff7c000 - 000000001ff80000 (ACPI NVS)
BIOS-e820: 000000001ff80000 - 0000000020000000 (reserved)
BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fffff000 - 0000000100000000 (reserved)
511MB LOWMEM available.
On node 0 totalpages: 130928
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126832 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI present.
ACPI: RSDP (v000 SENSX ) @ 0x000f7530
ACPI: RSDT (v001 SENSX AQUILA 0x06040000 SENS 0x00000000) @ 0x1ff77ded
ACPI: FADT (v001 SENSX SENSX10 0x06040000 SENS 0x00000050) @ 0x1ff7bf64
ACPI: BOOT (v001 SENSX $SBFTBL$ 0x06040000 SENS 0x00000001) @ 0x1ff7bfd8
ACPI: SSDT (v001 INTEL EISTRef 0x00002000 INTL 0x20020725) @ 0x1ff77e1d
ACPI: DSDT (v001 SENSX AQUILA 0x06040000 MSFT 0x0100000e) @ 0x00000000
Built 1 zonelists
Kernel command line: root=/dev/discs/disc0/part7 ro
No local APIC present or hardware disabled
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1595.820 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 513544k/523712k available (3316k kernel code, 9628k reserved, 956k data, 160k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3153.92 BogoMIPS (lpj=1576960)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: afe9f9bf 00000000 00000000 00000000
CPU: After vendor identify, caps: afe9f9bf 00000000 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9f9bf 00000000 00000000 00000040
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel(R) Pentium(R) M processor 1.60GHz stepping 06
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: IRQ9 SCI: Edge set to Level Trigger.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd9d1, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040816
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs *10)
ACPI: PCI Interrupt Link [LNKD] (IRQs *10)
ACPI: PCI Interrupt Link [LNKE] (IRQs *5)
ACPI: PCI Interrupt Link [LNKF] (IRQs 5) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 10) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs *5)
ACPI: Embedded Controller [H_EC] (gpe 28)
ACPI-0405: *** Error: Handler for [EmbeddedControl] returned AE_BAD_PARAMETER
ACPI-1133: *** Error: Method execution failed [_SB_.PCI0.LPCB.H_EC._REG] (Node c14e25a0), AE_BAD_PARAMETER
ACPI: Power Resource [PFAN] (on)
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:1d.1[b] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 5
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1f.3[b] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:00:1f.5[b] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:00:1f.6[b] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:02:03.1[b] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:02:03.2[C] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 5
ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 5 (level, low) -> IRQ 5
Simple Boot Flag at 0x36 set to 0x1
Machine check exception polling timer started.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
SGI XFS with ACLs, security attributes, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
vesafb: probe of vesafb0 failed with error -6
ACPI-0405: *** Error: Handler for [EmbeddedControl] returned AE_BAD_PARAMETER
ACPI-1133: *** Error: Method execution failed [_SB_.ADP1._PSR] (Node dff5fac0), AE_BAD_PARAMETER
ACPI-0405: *** Error: Handler for [EmbeddedControl] returned AE_BAD_PARAMETER
ACPI-1133: *** Error: Method execution failed [_SB_.BAT1._STA] (Node dff5f980), AE_AML_NO_RETURN_VALUE
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID0]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Fan [FAN0] (on)
ACPI: Processor [CPU0] (supports C1 C2 C3, 4 throttling states)
ACPI-0405: *** Error: Handler for [EmbeddedControl] returned AE_BAD_PARAMETER
ACPI-1133: *** Error: Method execution failed [_TZ_.THRM._TMP] (Node dff5fd40), AE_BAD_PARAMETER
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 10 (level, low) -> IRQ 10
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1860-0x1867, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x1868-0x186f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: FUJITSU MHT2060AT, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: MATSHITADVD-RAM UJ-812, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
ide2: Wait for ready failed before probe !
Probing IDE interface ide3...
ide3: Wait for ready failed before probe !
Probing IDE interface ide4...
ide4: Wait for ready failed before probe !
Probing IDE interface ide5...
ide5: Wait for ready failed before probe !
hda: max request size: 128KiB
hda: 117210240 sectors (60011 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 < p5 p6 p7 >
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
Synaptics Touchpad, model: 1
Firmware: 5.9
180 degree mounted touchpad
Sensor: 46
new absolute packet format
Touchpad has extended capability bits
-> middle button
-> multifinger detection
-> palm detection
input: SynPS/2 Synaptics TouchPad on isa0060/serio4
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
ACPI: (supports S0 S3 S4 S5)
ACPI wakeup devices:
PWRB LANC MODM
ReiserFS: hda7: found reiserfs format "3.6" with standard journal
ReiserFS: hda7: using ordered data mode
ReiserFS: hda7: journal params: device hda7, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda7: checking transaction log (hda7)
ReiserFS: hda7: replayed 3 transactions in 0 seconds
ReiserFS: hda7: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 160k freed
Adding 2096440k swap on /dev/discs/disc0/part6. Priority:-1 extents:1
ReiserFS: hda7: Removing [57894 164228 0x0 SD]..done
ReiserFS: hda7: There were 1 uncompleted unlinks/truncates. Completed
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 855PM Chipset.
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 256M @ 0xe0000000
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.0: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 11, io base 00001800
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1[b] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:1d.1: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 10, io base 00001820
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:1d.2: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 10, io base 00001840
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 5 (level, low) -> IRQ 5
ehci_hcd 0000:00:1d.7: Intel Corp. 82801DB/DBM (ICH4/ICH4-M) USB 2.0 EHCI Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 5, pci mem e0a28000
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
ACPI: PCI interrupt 0000:00:1f.5[b] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 49437 usecs
intel8x0: clocking to 48000
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ACPI: PCI interrupt 0000:00:1f.6[b] -> GSI 11 (level, low) -> IRQ 11
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-6111 Tue Jul 27 07:55:38 PDT 2004
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:02:03.0 [144d:c00f]
Yenta: ISA IRQ mask 0x0018, PCI irq 11
Socket status: 30000006
PCI: Enabling device 0000:02:03.1 (0000 -> 0002)
ACPI: PCI interrupt 0000:02:03.1[b] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:02:03.1 [144d:c00f]
Yenta: ISA IRQ mask 0x0098, PCI irq 11
Socket status: 30000006
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
ACPI: PCI interrupt 0000:02:03.2[C] -> GSI 10 (level, low) -> IRQ 10
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10] MMIO=[d0003000-d00037ff] Max Packet=[2048]
b44.c:v0.94 (May 4, 2004)
ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 10 (level, low) -> IRQ 10
eth0: Broadcom 4400 10/100BaseT Ethernet 00:00:f0:72:2a:e0
ieee80211_crypt: registered algorithm 'NULL'
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 0.12
ipw2200: Copyright(c) 2003-2004 Intel Corporation
ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 5 (level, low) -> IRQ 5
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0000f041080223a1]
eth1394: $Rev: 1224 $ Ben Collins <bcollins@debian.org>
eth1394: eth2: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
b44: eth0: Link is down.
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is on for TX and on for RX.
ieee80211_crypt: registered algorithm 'WEP'
NVRM: not using NVAGP, AGPGART is loaded!!
NVRM: not using NVAGP, AGPGART is loaded!!
ACPI-0405: *** Error: Handler for [EmbeddedControl] returned AE_BAD_PARAMETER
ACPI-1133: *** Error: Method execution failed [_SB_.LID0._LID] (Node c14e06a0), AE_AML_NO_RETURN_VALUEAnd finally my kernel config: http://members.chello.at/ezechiel/config-2.6.9-r2
I hope anybody can give me some advice or performance tip.
thx!
Offline
Pages: 1