You are not logged in.

Pages: 1

#1 2009-12-09 15:16:35

frojnd
Member
Registered: 2008-09-20
Posts: 125

smartctl reports errors. Is tehre a way to save disk?

I don't know why but I just made long smartctl test: 

smartctl -d ata -t long /dev/sda

and the output:

smartctl version 5.38 [x86_64-unknown-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Model Family:     Toshiba 2.5" HDD series (80 GB and above)
Device Model:     TOSHIBA MK1234GSX
Serial Number:    27KLTKHBT
Firmware Version: AH001D
User Capacity:    120,034,123,776 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   7
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Wed Dec  2 01:16:02 2009 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x80)    Offline data collection activity
                    was never started.
                    Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)    The previous self-test routine completed
                    without error or no self-test has ever 
                    been run.
Total time to complete Offline 
data collection:          ( 435) seconds.
Offline data collection
capabilities:              (0x5b) SMART execute Offline immediate.
                    Auto Offline data collection on/off support.
                    Suspend Offline collection upon new
                    command.
                    Offline surface scan supported.
                    Self-test supported.
                    No Conveyance Self-test supported.
                    Selective Self-test supported.
SMART capabilities:            (0x0003)    Saves SMART data before entering
                    power-saving mode.
                    Supports SMART auto save timer.
Error logging capability:        (0x01)    Error logging supported.
                    General Purpose Logging supported.
Short self-test routine 
recommended polling time:      (   2) minutes.
Extended self-test routine
recommended polling time:      (  86) minutes.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   100   100   050    Pre-fail  Always       -       0
  2 Throughput_Performance  0x0004   100   100   000    Old_age   Offline      -       0
  3 Spin_Up_Time            0x0027   100   100   001    Pre-fail  Always       -       1614
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       1288
  5 Reallocated_Sector_Ct   0x0033   100   100   050    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000a   100   100   000    Old_age   Always       -       0
  8 Seek_Time_Performance   0x0004   100   100   000    Old_age   Offline      -       0
  9 Power_On_Hours          0x0032   076   076   000    Old_age   Always       -       9985
 10 Spin_Retry_Count        0x0032   125   100   000    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       1263
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       58
193 Load_Cycle_Count        0x0032   079   079   000    Old_age   Always       -       217767
194 Temperature_Celsius     0x0022   100   100   000    Old_age   Always       -       47 (Lifetime Min/Max 10/69)
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
220 Disk_Shift              0x0002   100   100   000    Old_age   Always       -       119
222 Loaded_Hours            0x0032   078   078   000    Old_age   Always       -       8844
223 Load_Retry_Count        0x0032   100   100   000    Old_age   Always       -       0
224 Load_Friction           0x0022   100   100   000    Old_age   Always       -       0
226 Load-in_Time            0x0026   100   100   000    Old_age   Always       -       322
240 Head_Flying_Hours       0x0000   100   100   000    Old_age   Offline      -       0

SMART Error Log Version: 1
ATA Error Count: 10 (device log contains only the most recent five errors)
    CR = Command Register [HEX]
    FR = Features Register [HEX]
    SC = Sector Count Register [HEX]
    SN = Sector Number Register [HEX]
    CL = Cylinder Low Register [HEX]
    CH = Cylinder High Register [HEX]
    DH = Device/Head Register [HEX]
    DC = Device Command Register [HEX]
    ER = Error register [HEX]
    ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 10 occurred at disk power-on lifetime: 3506 hours (146 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 60 c1 97 e3  Error: UNC 8 sectors at LBA = 0x0397c160 = 60277088

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 08 60 c1 97 e3 00   1d+00:10:47.956  READ DMA
  27 00 00 00 00 00 e0 00   1d+00:10:47.956  READ NATIVE MAX ADDRESS EXT
  ec 00 00 00 00 00 a0 00   1d+00:10:47.935  IDENTIFY DEVICE
  ef 03 45 00 00 00 a0 00   1d+00:10:47.928  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00   1d+00:10:47.928  READ NATIVE MAX ADDRESS EXT

Error 9 occurred at disk power-on lifetime: 3506 hours (146 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 60 c1 97 e3  Error: UNC 8 sectors at LBA = 0x0397c160 = 60277088

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 08 60 c1 97 e3 00   1d+00:10:41.160  READ DMA
  27 00 00 00 00 00 e0 00   1d+00:10:41.160  READ NATIVE MAX ADDRESS EXT
  ec 00 00 00 00 00 a0 00   1d+00:10:41.153  IDENTIFY DEVICE
  ef 03 45 00 00 00 a0 00   1d+00:10:41.152  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00   1d+00:10:41.152  READ NATIVE MAX ADDRESS EXT

Error 8 occurred at disk power-on lifetime: 3506 hours (146 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 60 c1 97 e3  Error: UNC 8 sectors at LBA = 0x0397c160 = 60277088

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 08 60 c1 97 e3 00   1d+00:10:34.385  READ DMA
  27 00 00 00 00 00 e0 00   1d+00:10:34.385  READ NATIVE MAX ADDRESS EXT
  ec 00 00 00 00 00 a0 00   1d+00:10:34.376  IDENTIFY DEVICE
  ef 03 45 00 00 00 a0 00   1d+00:10:34.369  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00   1d+00:10:34.369  READ NATIVE MAX ADDRESS EXT

Error 7 occurred at disk power-on lifetime: 3506 hours (146 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 60 c1 97 e3  Error: UNC 8 sectors at LBA = 0x0397c160 = 60277088

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 08 60 c1 97 e3 00   1d+00:10:27.615  READ DMA
  c8 00 08 38 af 8d e3 00   1d+00:10:27.603  READ DMA
  c8 00 08 60 98 89 e3 00   1d+00:10:27.592  READ DMA
  c8 00 08 90 f5 92 e3 00   1d+00:10:27.587  READ DMA
  c8 00 08 a0 97 90 e3 00   1d+00:10:27.577  READ DMA

Error 6 occurred at disk power-on lifetime: 3506 hours (146 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 50 60 c1 97 e3  Error: UNC 80 sectors at LBA = 0x0397c160 = 60277088

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 00 b0 c0 97 e3 00   1d+00:10:12.260  READ DMA
  27 00 00 00 00 00 e0 00   1d+00:10:12.260  READ NATIVE MAX ADDRESS EXT
  ec 00 00 00 00 00 a0 00   1d+00:10:12.252  IDENTIFY DEVICE
  ef 03 45 00 00 00 a0 00   1d+00:10:12.244  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00   1d+00:10:12.244  READ NATIVE MAX ADDRESS EXT

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%      9984         -
# 2  Short offline       Completed without error       00%      6312         -
# 3  Short offline       Completed without error       00%      3642         -
# 4  Short offline       Completed without error       00%      3342         -
# 5  Short offline       Completed without error       00%        15         -
# 6  Short offline       Completed without error       00%         2         -
# 7  Short offline       Completed without error       00%         0         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

My questions is is there a way to save disk? And is the information that I have 3506 hours left any near correct?

Offline

#2 2009-12-13 21:10:46

frojnd
Member
Registered: 2008-09-20
Posts: 125

Re: smartctl reports errors. Is tehre a way to save disk?

Sorry to bump, but does anyone know if there is a way to save disk and if the info about 3506hours left is legit?

Offline

#3 2009-12-13 21:17:38

vacant
Member
From: downstairs
Registered: 2004-11-05
Posts: 816

Re: smartctl reports errors. Is tehre a way to save disk?

The errors occurred after 3506 hours of uptime. Your disk passed its health assessment and has no "when failed" entries.

Offline

#4 2009-12-13 21:28:33

frojnd
Member
Registered: 2008-09-20
Posts: 125

Re: smartctl reports errors. Is tehre a way to save disk?

Thank you vacant for your reply. That is great news! My disk will last on smile

Offline

Pages: 1

Board footer

Powered by FluxBB